Samsung SIR-4150 User`s manual

High Resolution Day & Night IR Camera SIR-4150 User’s Manual
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
SALES NETWORK
•
SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, 462-120, Korea
TEL : +82-31-740-8151~8158 FAX : +82-31-740-8145
•
SAMSUNG OPTO-ELECTRONICS UK, LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey KT16 OPS
TEL : +44-1932-45-5308 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungcctv.com
P/No. : Z6806-0820-01C
VAN 08. 03
ENGLISH
Before operating the camera, confirm the camera model and proper input
power voltage. In order to that you can understand this manual thoroughly,
we'll introduce our model description.
■ SIR-4150 SERIES
• NTSC MODELS
SIR-4150N
• PAL MODELS
SIR-4150P
■ MODEL DESCRIPTION
• SIR-4150 _X
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
SIGNAL SYSTEM
• SIGNAL SYSTEM
N --> NTSC MODEL
P --> PAL MODEL
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
INFORMATION -This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Contents
6
Features
7
Warnings & cautions
21
22
11
• WHITE BALANCE control
22
11
12
13
• BACKLIGHT (Backlight Compensation)
24
• AGC (Auto Gain Control)
25
• SSNR (Samsung Super Noise Reduction)
26
• SENS UP (Low illuminance)
27
• SPECIAL
28
• EXIT
34
Overview
■ Front
Adjust to lens
14
■ Ajust to Lens’s ZOOM and Focus
14
Connection
15
■ Connecting to a monitor
15
16
17
■ Connecting to power
■ RS-485 Communication control
COLOR IR CAMERA
4
User’s Manual
18
19
■ Settings
• SHUTTER (condition and speed control)
10
■ Back
18
• LENS (Adjusting to the brightness level)
Components and Accessories
■ Bottom
Operating Your Camera
■ Menu
Troubleshooting
35
Specifications
36
COLOR IR CAMERA
5
User’s Manual
Features
Ultra High Sensitivity
Outdoor Visibility range 30M
The built-in high sensitivity COLOR CCD
enables a clear image even in 0Lux(B/W,
IR-LED ON)or lower illumination.
If B/W mode, IR-LED is lighted, 0 Luxes'
Outdoor visibility range 30 M guarantees is
available.
IRMODE Function
High Resolution
Featuring 520TV line horizontal resolution
in color mode and 570TV line horizontal
resolution in BW moe. The camera features
Sony’s 410,000 pixel CCD and capture
clean, noiseless high-quality image
This function that prevent short distance
saturation in case of IR LED is lighted,
discrimination of subject does possibility
within 3 M
RS-485 Function
Use RS485 communication and OSD menu
control does possibility to remote.
DAY&NIGHT(ICR)
This camera has a function that automatically
selects the mode that is appropriate for
daytime or night-time conditions.
The COLOR mode operates in daytime
conditions to provide optimum colors, and
BW mode operates in night-time conditions
to enhance the definition of the image.
IP65 Approved/Dust and Rain
Resistant
With dust and rain resistant design,the camera
can be installed outside under building eaves
or places that
are exposed to the dust and rain.
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to
provide customers with more environment-friendly products.The Eco mark
represents Samsung Techwin s will to create environment-friendly products,
and indicates that the product satisfies the EU RoHS Directive.
Warnings & Cautions
This information is provided to ensure your safety and to prevent any losses,
financial or otherwise. Please read it carefully and use the product accordingly.
* For product inquiries, please contact the retail shop where you bought the camera. The use of
equipment such as an aerial ladder while providing after-sales service shall be at your expense.
Notes
• SIR-4150 does not need special Housing because it is Housing built-in type. Please
remove front glass certainly in case of installation on outdoors style Housing inside.
Warning/Attention/Special Mark Messages
Ignoring this information may result
in material loss and/or serious
personal injuries including death.
Indicates “Never Allowed.”
Indicates “No Disassembling.”
Indicates Must Observe.
PRIVACY Masking Function
SSNR (Samsung Super Noise
Reduction)
By using built-in SSNR Chip manufactured
by SAMSUNG TECHWIN, the amount of
low illuminance noise has been significantly
reduced, and the signal-to-noise ratio (S/N)
as well as horizontal resolution have been
improved, resulting in a clear and sharp
image display even in the dark.
COLOR IR CAMERA
6
The PRIVACY masking function conceals
the areas you do not wish to appear on the
screen.
Additional Function
SENS-UP, MIRROR, SHARPNESS, MOTION
DET. functions are also available.
User’s Manual
COLOR IR CAMERA
7
User’s Manual
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Use only under temperature conditions
between -10˚C and +50˚C. Provide good
ventilation when using in high temperature
conditions.
Do not install under unstable
lighting conditions.
May lower image quality.
Do not drop the camera or
subject it to physical shock.
May cause a product malfunction.
Never keep the camera face to
strong light directly.
May damage the CCD.
Do not expose the camera to
radioactivity.
Avoid touching the camera lens.
Radioactivity exposure may damage the
CCD.
Notes
Severe lighting changes or flickering may
hinder normal camera operation.
COLOR IR CAMERA
8
The lens is the most important component
of the camera. Be careful not to smear it
with fingerprints.
User’s Manual
• Exposure to a spotlight or an object emitting strong light may cause smear or
blooming.
• Ensure that the power source complies with normal specifications before supplying
it to the camera.
• In case of IR LED has been lighted, do not lighten directly eye.
COLOR IR CAMERA
9
User’s Manual
Overview
Components and Accessories
FRONT
1. High Resolution Day&Night IR Camera
SIR-4150
2. CAMERA HOOD
3. HOOD ADAPTOR(2EA)
4. USER’S MANUAL
Hood
Hood adaptor
Fixing the hood onto the camera
Focus lever
Set focus of lens by turn the focus lever
Zoom lever
Set zoom magnification of lens by turn the zoom lever
Front cover fixing screw
5. DC 12V/4A ADAPTOR
Notes
6. POWER CABLE
• Adjust to the zoom & focus lever, and then use after fixate turning lever to clockwise.
• When you adjust to the ZOOM&FOCUS of the lens, Please loosen the Front cover
fixing screw and separate Front cover from the camera.
COLOR IR CAMERA
10 User’s Manual
COLOR IR CAMERA
11 User’s Manual
Overview
BACK
BOTTOM
L
Mounting bracket screw hole
Please use the screw hole when fixing the
camera onto the mounting bracket.
Please use the clamp screw as specified below.
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
Power input terminal
*The mounting bracket can be separated and attached to
the top of the camera.
In this instance please do not tighten the screw to a
depth of more than 4mm, otherwise serious damage can
occur to the inside of the camera.
Video output terminal
RS-485 control terminal
Note
• This camera package does not include the mounting bracket. Please refer to the
user's manual for installation of the mounting bracket.
COLOR IR CAMERA
12 User’s Manual
COLOR IR CAMERA
13 User’s Manual
Adjust to Lens
Connection
Adjust to the lens's zoom and focus.
Connecting to Monitor
1. Please loosen a front cover fixing screw with picture and separate cover
2. Please unlock the Zoom or Focus lever to release it.
3. Adjust the zoom or focus lever by moving it to WIDE(NEAR)or TELE(FAR)
position.
4. After adjustment, tighten the zoom or focus lever, taking care that the
adjusted position does not change.
5. Please close cover and tighten the front cover fixing screw.
Please connect the video output terminal located on the back of the camera to
the monitor.
Monitor
CCD Camera
• The connection method varies depending on the type of monitor and accessories.
Please refer to the user's manual for each instrument.
• Please turn off the power when connecting.
• Please select Hi-Z on the 75Ω/Hi-Z switch for the intermediate video TV set
and select 75Ω for the Intermediate device as shown in the picture below.
Front cover fixing screw
Focus lever
CCD Camera
ZOOM lever
Intermediate
Note
• If front cover fixing screw do not pinch, it is not waterproof.
COLOR IR CAMERA
14 User’s Manual
COLOR IR CAMERA
15 User’s Manual
End monitor
Connecting to Power
RS-485 communication control
The recommended adaptor specification for SIR-4150N/P is DC 12V/4A.
Please check the standard power requirement before connecting to power.
Connecting to RS-485 CONTROL TERMINAL
CONTROL TERMINAL SPEC
WHITE (TRX+)
RS-485+
BLACK (TRX-)
RS-485-
When the resistance value of copper wire is at [20°C(68°F)]
Copper wire size(AWG)
#24(0.22mm2)
#22(0.33mm2)
#20(0.52mm2)
#18(0.83mm2)
Resistance value(Ω/m)
0.078
0.050
0.030
0.018
Voltage drop(V/m)
0.028
0.018
0.011
0.006
• As shown in the table above, voltage decreases as the wire gets longer.
Therefore use of an excessively long adaptor output line for connection to
the camera may affect the performance of the camera.
Standard voltage for camera operation : DC 12V±10%
There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
Note
• Please must be used adaptor that meets the standard requirement.
• Please connect the power after installation.
COLOR IR CAMERA
16 User’s Manual
Using a RS-485 communication, it will be able to control the OSD menu at the
SAMSUNG TECHWIN System Controller or DVR.
(1) The case which it controls from the PC
Using a RS-485 converter, It connects to RS-485 CONTROL TERMINAL outside
camera and serial cable
EX) SERIAL PORT OF THE PC(COM1) — SERIAL CABLE -- RS-485 CONVERTER
-- RS-485 CONTROL TERMINAL
(2)The case which it controls from the DVR or System Controller
It connects the RS-485 CONTROL TERMINAL in the connection terminal of 485
control boards which are connected with the DVR or System Controller.
485 CONTROL BOARD CONNECTION TERMINAL
(+)CONNECTION TERMINAL
(-)CONNECTION TERMINAL
RS-485 CONTROL TERMINAL
WHITE (TRX+)
BLACK (TRX-)
Notes
• When you construct external control systems for a camera control, please use to
the PELCO-D PROTOCOL.
• When you connecting to RS-485 CONTROL TERMINAL, please peel off the outer
skin inside the RS-485 CONTROL TERMINAL.
COLOR IR CAMERA
17 User’s Manual
Operating Your Camera
Menu
Settings
Settings can be made using the RS-485 communication.
Please refer 14 pages (RS-485 communication control) and connect to the RS485 control terminal(TRX+, TRX-)
SETUP menu
LENS
• DC
SHUTTER
(condition and speed control)
•- - - -
• FLK
WHITE BALANCE control
• ATW
• AWC
• MANUAL
BACKLIGHT
(Backlight compensation)
• OFF
• HIGH
• LOW
• MIDDLE
AGC (Auto Gain control)
• OFF
• NORMAL
• HIGH
SSNR
(Samsung super noise reduction)
• OFF
• HIGH
• LOW
• MIDDLE
SENS-UP (Low illuminance)
• OFF
• AUTO
SPECIAL
• CAMERA ID
• MOTION DET
• COMM ADJ
• IRMODE
• RETURN
• DAYNIGHT
• PRIVACY
• IMAGE ADJ
• RESET
1. When use SCC-3100A PELCO-D Protocol setting method
< SETUP SYSTEM MENU >
PTZ selection : PTZ SETUP2 selection
1)MODEL:PTZ ID, PELCO-D
Protocol selection.
CONTROLLER selection : SERIAL selection 1. BAUD, 2. DATA, 3. STOP
BIT, 4. PARITY setting
* OSD button : Display OSD menu on the monitor or there is a sub-menu which
can be selected by pressing OSD button.
* JOYSTICK : It can move menu cursor by upside, downward, the left side and
the right side . Joystick do Up/Down/Right/Left button functions
according to 4 directions that move.
LEFT BUTTON
UP BUTTON
RIGHT BUTTON
DOWN BUTTON
OSD SETUP BUTTON
Notes
• Please set RS-485 communication setting of controller and camera equally.
EXIT
COLOR IR CAMERA
18 User’s Manual
COLOR IR CAMERA
19 User’s Manual
Operating Your Camera
1. Please press the SETUP button.
• Settings can now be made. The SETUP menu is displayed on the monitor.
SETUP
1.LENS
2.SHUTTER
3.WHITE BAL.
4.BACKLIGHT
5.AGC
6.SSNR
7.SENS-UP
8.SPECIAL
9.EXIT
DC
--ATW
OFF
NORMAL
LOW
OFF
LENS (Adjusting to the brightness level)
This function is used to adjust the brightness of the screen.
1. When the SETUP menu is displayed on the screen, please position the arrow
to point to 'LENS' by using the UP and DOWN buttons.
2. Using the SETUP button, you can control the brightness of the screen.
2. Please select any function you wish to activate by using the UP and DOWN
buttons.
• The arrow can be moved up or down by using the UP and DOWN buttons.
Please position the arrow to point to the function you wish to operate.
Select any function you
wish to operate by
using the UP and
DOWN buttons.
SETUP
1.LENS
2.SHUTTER
3.WHITE BAL.
4.BACKLIGHT
5.AGC
6.SSNR
7.SENS-UP
8.SPECIAL
9.EXIT
DC
--ATW
OFF
NORMAL
LOW
OFF
Modes can be
changed using the
LEFT and RIGHT
buttons.
3. Please press the LEFT or RIGHT button if you wish to change mode.
• When the LEFT or RIGHT button is pressed, available values and modes
are displayed in order. Please keep pressing the button until you get to the
mode you wish to operate.
4. Please select 'EXIT' and then press the SETUP button to finish the setting.
COLOR IR CAMERA
20 User’s Manual
Note
• If appears at the mode you wish to operate, it means that there is a sub-menu
which can be selected by pressing the SETUP button.
appears at the mode item, it means that there is no mode available to be
• If
selected.
SETUP
1.LENS
2.SHUTTER
3.WHITE BAL.
4.BACKLIGHT
5.AGC
6.SSNR
7.SENS-UP
8.SPECIAL
9.EXIT
DC
--ATW
OFF
NORMAL
LOW
OFF
3. Please press the SETUP button if you wish to
return to the previous menu.
COLOR IR CAMERA
21 User’s Manual
Operating Your Camera
SHUTTER (condition and speed control)
Because SIR-4150 uses built-in dc lens, shutter speed is fixed at 1/60 basically.
SETUP
1.LENS
2.SHUTTER
3.WHITE BAL.
4.BACKLIGHT
5.AGC
6.SSNR
DC
--ATW
OFF
NORMAL
LOW
- - - - : Shutter speed is fixed at 1/60(1/50)
FLK : Please select 'FLK' mode when flickering occurs on the screen, due to
an imbalance between illumination and frequency.
NTSC Model : 1/100, PAL MODEL : 1/120
WHITE BALANCE control
The screen color can be adjusted by using the WHITE BALANCE function.
1. Please position the arrow to point to 'WHITE BAL' on the SETUP menu by
using the UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
SETUP
1.LENS
2.SHUTTER
3.WHITE BAL.
4.BACKLIGHT
5.AGC
6.SSNR
COLOR IR CAMERA
Please select one of the 3 modes below.
ATW(Auto Tracking White Balance) : This mode can be used within the color
temperature range 1,800˚K ~ 10,500˚K (Ex. fluorescent light, outdoor, sodium
vapor lamp or inside tunnels)
AWC(Auto White Balance Control) : Please press the SETUP button while the
camera is directed at a piece of white paper to obtain the optimum state under
current illumination. If the environment including the light source is changed, you
have to adjust the white balance again.
MANUAL: The manual adjustment mode enables finer adjustment. Please select
ATW or AWC first. Please change to manual adjustment mode and press the SETUP
button. Please set the appropriate color temperature, and then increase or decrease
the red and blue color values while monitoring the color changes on the object.
Note
• Under the following conditions the WHITE BALANCE function may not operate
properly. In such cases, please select the AWC mode.
1. When the object’s surroundings have a very high color temperature.
(Ex. a clear sky and sunset)
2. When the object’s surroundings are dark.
3. If the camera directly faces a fluorescent light or is installed in a place where
there are considerable changes in illumination, the WHITE BALANCE function
may become unstable.
DC
--ATW
OFF
NORMAL
LOW
22 User’s Manual
COLOR IR CAMERA
23 User’s Manual
Operating Your Camera
BACKLIGHT (Backlight Compensation)
AGC (Auto Gain Control)
When there is a strong backlight behind the object, clear images of the background
as well as the object can still be obtained by using the BACKLIGHT function.
1. Please position the arrow to point to 'BACKLIGHT' on the SETUP menu by
using the UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
SETUP
1.LENS
2.SHUTTER
3.WHITE BAL.
4.BACKLIGHT
5.AGC
DC
--ATW
OFF
NORMAL
HIGH/MIDDLE/LOW :
You can adjust the sensitivity of BLC and
BLC window’s size and position. So that, It can
achieve BLC function efficiently regardless of
position of subject.
OFF : BLC function doesn’t operate.
1. Please position the arrow to point to 'AGC' on the SETUP menu by using the
UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT
button. As the level of gain increases, the screen gets brighter and the level
of noise also increases.
HIGH
: The gain increases or decreases within the range of 6dB ~ 34dB.
NORMAL : The gain increases or decreases within the range of 6dB ~ 30dB.
OFF
: The gain is fixed at 6dB.
SETUP
1.LENS
2.SHUTTER
3.WHITE BAL.
4.BACKLIGHT
5.AGC
6.SSNR
7.SENS-UP
8.SPECIAL
9.EXIT
DC
--ATW
OFF
NORMAL
LOW
OFF
3. Please press the SETUP button. The BRIGHTNESS can be adjusted within the
range of 1~70.
BACKLIGHT ON
BACKLIGHT OFF
Note
• When BW mode at night-time, BLC does not operate.
COLOR IR CAMERA
24 User’s Manual
4. Please press the SETUP button when all the settings are complete.
COLOR IR CAMERA
25 User’s Manual
Operating Your Camera
SSNR (Samsung Super Noise reduction)
The background noise in the low light level decreases automatically as the level
of gain changes.
1. Please position the arrow to point to 'SSNR' on the SETUP menu by using the
UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
SETUP
1.LENS
2.SHUTTER
3.WHITE BAL.
4.BACKLIGHT
5.AGC
6.SSNR
7.SENS-UP
8.SPECIAL
9.EXIT
DC
--ATW
OFF
NORMAL
LOW
OFF
: There is no reduction in noise level.
: There is a small reduction in noise level with almost no ghost
image.
MIDDLE : The most effective mode. There is a sufficient reduction in noise
levels without causing much ghost imaging.
HIGH : The level of noise is reduced greatly, however there is an increase
in ghost imaging.
SENS UP (Low illuminance)
SENS UP helps maintain a bright, clear screen image by automatically detecting
changes in the level of light in low light level conditions.
1. Please position the arrow to point to 'SENS UP' on the SETUP menu by using the
UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
AUTO : Low light level auto mode
OFF : The function does not operate.
Note
• When SHUTTER is in the manual mode, SENS UP does not operate.
• When AGC is turned off, SENS UP does not operate.
SETUP
1.LENS
2.SHUTTER
3.WHITE BAL.
4.BACKLIGHT
5.AGC
6.SSNR
7.SENS-UP
OFF
LOW
Note
• When AGC is turned off, SSNR does not operate.
COLOR IR CAMERA
26 User’s Manual
DC
--ATW
OFF
NORMAL
LOW
OFF
3. Please press the SETUP button when all the settings are complete.
Note
• The maximum storage magnification in low light level can be adjusted by pressing
the SETUP button in 'AUTO' mode.(X2~X128)
• As the magnification increases, the screen gets brighter; moving object gets more
afterimage.
• If storage magnification is increased while SENS UP is operating, it may cause
noise, and spots may appear; however this is normal.
COLOR IR CAMERA
27 User’s Manual
Operating Your Camera
3) Please press the SETUP button.
SPECIAL
1. Please position the arrow to point to 'SPECIAL' on the SETUP menu by using
the UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the UP or DOWN button.
SPECIAL
10.CAMERA ID
11.DAYNIGHT
12.MOTION DET
13.PRIVACY
14.COMM ADJ
15.IMAGE ADJ
16.IRMODE
17.RESET
18.RETURN
OFF
AUTO
OFF
OFF
4) Up to 15 letters can be used for the ID.
Please move the cursor to the letter you wish to choose by using the UP and
DOWN button.
CAMERA ID : If the ID is input, the camera ID appears on the monitor.
1) Please position the arrow to point to 'CAMERA ID' by using the UP or DOWN
button.
2) Please select 'ON' by pressing the LEFT or RIGHT button.
Note
• If 'OFF' is selected, the ID does not appear
on the monitor even if it has been input.
COLOR IR CAMERA
SPECIAL
10.CAMERA ID
11.DAYNIGHT
12.MOTION DET
13.PRIVACY
14.COMM ADJ
15.IMAGE ADJ
16.IRMODE
17.RESET
18.RETURN
28 User’s Manual
OFF
AUTO
OFF
OFF
Select an ID from A,B~Y,Z, a,b~y,z, 0,1~8,9 by using the UP, DOWN, LEFT
and RIGHT buttons.
Please lock in the letters by using the SETUP button.
• When the letter is locked in, the cursor moves to the next space.
Please repeat the above to input the ID.
Note
• If the wrong name has been input.....
If you press the SETUP button after moving the cursor to CLR, all the letters
will be erased. If you want to correct a letter, please move the cursor to the
arrow at the bottom left of the screen and press 'SET'.
Please position the cursor above the letter you wish to correct, and then move
the cursor onto the letter you wish to choose and press the SETUP button.
COLOR IR CAMERA
29 User’s Manual
Operating Your Camera
5) When a name has been chosen, please select a position for the name display.
Please move the cursor onto 'POS' and then press the SETUP button.
DAY&NIGHT (ICR TYPE) : Select from COLOR, B/W or AUTO modes.
•AUTO: According to the input luminance level, IR Cut Filter is automatically
switched to the appropriate mode for daytime or night-time. The COLOR
mode is operated for daytime, and it converts to BW mode for night-time
The name will appear at the top left hand corner.
•COLOR : COLOR mode
•B/W : BW mode. Please press SETUP button to turn on or off the burst signal on
BW mode.
FRONT DOOR
to Locate, then SET
Please find the position you wish to display the name by using the 4
directional buttons, and then press the SETUP button.
FRONT DOOR
to Locate, then SET
6) Please select 'END' and then press the SETUP button to complete ID input.
COLOR IR CAMERA
30 User’s Manual
Note
• If AGC is OFF, you can't select AUTO mode and B/W mode.
When DayNight mode is set to Auto under the condition which the strong IR light
is flickering periodically, a malfunction of IR-Cut filter may occur.
MOTION DETECTION :
This product has a feature that allows you to observe movements of objects in 4
different areas on the screen, and the words 'MOTION DETECTED' appear on the
screen when movement is detected; hence a single individual can conduct
supervision efficiently. The camera detects an object's movement by sensing
disparity of outline, and level of brightness and color.
• Please press the SETUP button.
- OFF : MOTION DETECTION mode is cancelled.
- ON : Any motion in the selected areas is observed.
• Please select the area you wish to observe from the 3 areas in AREA SEL mode.
• Please select ON mode for the chosen area.
COLOR IR CAMERA
31 User’s Manual
Operating Your Camera
• Please adjust the size of the area to be observed by using the UP, DOWN, LEFT
or RIGHT button.
COM ADJ :
When wish to control CAMERA by external communication control device, it is
function that set up CAMERA's communication states and protocol.
• Please press the SETUP button to save the changes and complete the setting.
• CAM ID
Note
• There is no ‘MD’ output signal. ‘MD’ is on screen display only words.
PRIVACY : Mask privacy area you do not wish to appear on the screen.
- OFF : Cancels the PRIVACY mode.
- ON : Operates the PRIVACY mode.
• Please press the SETUP button.
• Please select the area you do not wish to appear from the 4 areas in AREA SEL
mode.
• Please select ON mode for the chosen area.
• Please adjust the size of the area to be concealed by using the UP, DOWN,
LEFT or RIGHT button.
: Assign ID number to the camera. It is restricted available to set
ID from 1~255
• DISP CAMID : Displays CAM ID on the top left of the screen.
• BAUD RATE : Configure baud rate from 9600bps, 19200bps, 38400bps,
57600bps.
• UART MODE: Configure parity bit to NONE,EVEN, or ODD. Data bit is set to 8bit
and stop bit to 1bit.
• END
Note
• Please set CAM ID of CAMERA and external communication control device equally.
IMAGE ADJ : Includes image quality or special function factors.
• MIRROR : Sets a horizontal image inversionj.
MIRROR ON
COLOR IR CAMERA
32 User’s Manual
COLOR IR CAMERA
MIRROR OFF
33 User’s Manual
Operating Your Camera
• SHARPNESS : The outline of the video image becomes cleaner and more
distinctive as the level of SHARPNESS increases. If the level
goes up excessively, however, it may affect the video image and
generate noise.
IRMODE : If IR LED turned on at night, this function prevents phenomenon that
screen center is saturated according to size of window that set. So the
identification of the subject is possible within short distance 3M
RESET : Returns to the level which was set by the manufacturer for shipment.
RETURN : Returns to the SETUP menu.
EXIT
Saves all the setting menus and then exits.
COLOR IR CAMERA
34 User’s Manual
Troubleshooting
If there are problems in operation, please refer to the items below. If the
problem persists, please contact the agent you purchased this product from.
Problem
Solution
Nothing appears on the screen.
• Please check the power connection.
• Please check the video signal line connection.
The video image is not clear.
• Please check if the lens is clean.
Please clean the lens with a clean cloth or brush.
• Please adjust the contrast feature of the monitor.
• Please make sure that the screen is not exposed directly to
a bright light. Please move the camera if necessary.
The screen is dark.
• Please adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75Ω/ Hi-z
properly, and check the terminals.
There is a problem with the
camera operation. The camera
surface is too hot and black
stripes appear on the screen.
• Please check if an appropriate power source to the
camera complies with the manufacturer's standard
requirement, or if the voltage keeps changing.
Color are not quite right
• Please check the ‘WHITE BAL’ setting
DAY&NIGHT(AUTO, B/W)
mode doesn’t Operate.
• Please check if the AGC menu is set to the OFF position.
SENS-UP function doesn’t
operate.
• Please check if the AGC menu is set to the OFF position.
IR-LED isn’t lighted.
• Isn’t DAYNIGHT function setting up the color mode?
• Please change the AUTO or B/W mode.
OSD control doesn’t operate.
• Please confirm whether communication setting method
and RS485 control terminal connection fit.
COLOR IR CAMERA
35 User’s Manual
DECLARATION OF CONFORMITY
Specifications
SIR-4150N
C
C
D
S
y
n
c.
E
L
E
C
T
R
I
C
A
L
POWER
Sensor
Total Pixels
Effective Pixels
Scanning System
Synchronization
Frequancy
Resolution
Video Output
S/N (Y signal)
Min.
LED ON
Illumination LED OFF
Visibility Range
(IR LED ON)
Water Resistance
Day & Night(ICR)
Gain Control
White Balance
Electronic shutter speed
Back Light Compensation
SSNR
Sens-Up
O.S.D
Camera Title
Camera ID
Motion Detection
Communication
Mirror
Privacy
Sharpness
LENS
Operating
Temperature/Humidity
Dimension
Weight
SIR-4150P
DC12V±10%, 460mA/ 5 .5W(LED ON)
1/3 inch, Sony Super HAD CCD
811(H) x 508(V)
795(H) x 596(V)
768(H) x 494(V)
752(H) x 582(V)
2:1 Interlace
Internal Fixed
H:15.734 KHz, V :59.94 Hz
H: 15.625 KHz, V: 50.00 Hz
520 Lines(Color) / 570 Lines(B/W)
CVBS : 1.0Vp-p/75Ω
50 dB (AGC Off/Weight ON)
0 Lux
0.3 Lux(Color), 0.002(Sens-up)/ @F1.2
Indoor - Outdoor : 30m (IR LED number: 24EA)
IP65
AUTO/ COLOR / B/W
NORMAL/HIGH/OFF Selectable
ATW(1800˚K ~ 10,500˚K)/AWC/Manual
1/60 Fixed / Flickerless
1/50 Fixed / Flickerless
LOW/MIDDLE/HIGH/OFF Selectable
LOW/MIDDLE/HIGH/OFF Selectable
AUTO/OFF (selectable limit X2 _X128)
RS485 Control
OFF/ON (Displayed 15 characters)
255 ID Selectable
ON/OFF (4 Programmable Zone)
RS-485(9600, 19200, 38400 and 57600bps is selectable)
Pelco-D Protocol is available
ON/OFF
ON/OFF (4 Programmable Zone)
ON/OFF (Level Adjustable)
X2.5 Vari-Focal Lens (F1.2, f= 3.8mm ~ 9.5 mm)
COLOR IR CAMERA
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name
SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment
CCTV Camera
Model Name
SIR-4150P
Beginning Serial NO.
S7090001
Year of Manufacture
2007. 09. 01
Conformance to
EN 50081-1:1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4:1996
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Manufacturer
SAMSUNG TECHWIN CO., LTD
Legal Representative in Europe
HAN SEUG KIM
Full Name
Signature
Full Name
Signature
-10˚C to +50˚C / 30% to 80%
Position
QUALITY CONTROL MANAGER
Position
74(W) x 74(H) x 134.5(D)mm
585g
Place
CHANGWON, KOREA
Place
Date
2007. 9. 1
Date
36 User’s Manual