Automate AM1.5 Installation guide

AM1 Security System
installation guide
© 2005 Directed Electronics, Inc. Vista, CA N427A 01-05
NOTE: This product is intended for installation by a professional installer only! Any
attempt to install this product by any person other than a trained professional may
result in severe damage to a vehicle’s electrical system and components.
trademarks and copyrights
Bitwriter®, Clifford®, Code-Hopping®, Directed®, Doubleguard®, ESP®, FailSafe®, Ghost Switch®, Learn Routine™,
Nite-Lite®, Nuisance Prevention®, NPC®, Revenger®, Silent Mode™, Soft Chirp®, Stealth Coding™, Stinger®,
Valet®, Vehicle Recovery System™, VRS™, and Warn Away® are all Trademarks or Registered Trademarks of
Directed Electronics, Inc.
contents
what is included . . . . . . . . . . . . . . . .3
control module . . . . . . . . . . . . . . . .3
installation points to remember . . .3
before beginning the installation: 4
after the install: . . . . . . . . . . . . . .4
tools required . . . . . . . . . . . . . . . . .4
deciding on component location . .5
control module . . . . . . . . . . . . . .5
integrated LED/Valet® switch . . . .6
starter kill relay . . . . . . . . . . . . . .6
connecting your wires . . . . . . . . . . .6
obtaining constant 12V . . . . . . . .6
finding the 12V switched . . . . . . .
ignition wire . . . . . . . . . . . . . . . .7
finding the door pin switch circuit 9
main harness wire
..............
connection guide . . . . . . . . . . . . . .10
main harness wiring diagram . . .10
main harness wiring guide . . . . .10
auxiliary harness wire . . . . . . . . . . . .
connection guide . . . . . . . . . . . . . .15
auxiliary harness wiring diagram 15
auxiliary harness wiring guide . .15
keyless entry systems . . . . . . . . . . .
—three types . . . . . . . . . . . . . . .17
door lock harness wire . . . . . . . . . . .
connection guide . . . . . . . . . . . . . .20
plug-in harnesses . . . . . . . . . . . . . .20
integrated LED/Valet® switch . . .20
data port—Bitwriter® . . . . . . . . .20
© 2005 directed electronics, inc.
four-pin optional sensor harness .21
RED wire . . . . . . . . . . . . . . . . . .21
BLACK wire . . . . . . . . . . . . . . . .21
BLUE, GREEN wires . . . . . . . . . .21
dealer master control loop . . . . . .21
door lock learn routine . . . . . . . . .21
to learn lock: . . . . . . . . . . . . . . .22
to learn unlock: . . . . . . . . . . . . .22
to exit the learn routine: . . . . . .23
on-board dual stage shock sensor 23
internal programming jumper . . .24
zones . . . . . . . . . . . . . . . . . . . . . . . .24
long term event history . . . . . . . .25
rapid resume logic . . . . . . . . . . . . .25
feature programming . . . . . . . . . .26
to enter feature programming . . .
routine . . . . . . . . . . . . . . . . . . . .26
once a feature is programmed . .27
accessing another feature . . . . .27
accessing another menu . . . . . .27
exiting feature programming . . .27
Bitwriter® ONLY features . . . . . .28
features #1 menu . . . . . . . . . . .29
features #2 menu . . . . . . . . . . .30
master dealer remotes . . . . . . . . .31
master dealer remote learn . . . . . .
routine . . . . . . . . . . . . . . . . . . . .31
troubleshooting . . . . . . . . . . . . . . .33
wiring quick reference guide . . . .37
i
ii
© 2005 directed electronics, inc.
what is included
z
Control module
z
4-pin sensor harness
z
12-pin main harness
z
Integrated LED/Valet switch
z
7-pin door monitor/Aux harness
z
3-pin door lock harness
control module
OPTIONAL
RECEIVER
(NOT USED)
DEALER
MASTER
CONTROL
LOOP
BITWRITER®
SHOCK SENSOR
ADJUSTMENT
7-PIN DOOR MONITOR/
AUX HARNESS
DOOR LOCK
10-AMP
FUSE/JUMPER
ACCESS
LED (INTEGRATED LED/
VALET® SWITCH)
VALET®
(INTEGRATED
LED/VALET
SWITCH)
12-PIN
MAIN
HARNESS
OPTIONAL
SENSOR
INPUT
(506T OR 504D)
installation points to remember
This product represents many years of research and development. It is very sophisticated and should be installed by experienced security installers only. Please do not
attempt installation of this product without reading this guide. The system has been designed to provide the ultimate in security, coupled with limitless convenience and expansion options.
This product is not intended for consumer installation and will have NO WARRANTY
unless it is installed by an authorized dealer.
© 2005 directed electronics, inc.
3
Do not disconnect the battery if the vehicle has an anti-theft coded radio. If equipped
with an airbag, avoid disconnecting the battery if possible.
IMPORTANT! Please read this entire installation guide before beginning the installation. The installation of this security system requires interfacing with many of the vehicle’s systems. Many new vehicles use low-voltage or multiplexed systems which can
be damaged by low resistance testing devices, such as test lights or logic probes. Test
all circuits with a high-quality digital multi-meter before making the connections.
MPORTANT! Many airbag systems will display a diagnostic code through their warnIM
ing light after they lose power. Disconnecting the battery requires this code to be
erased, a procedure that can require a trip to the dealer.
before beginning the installation:
z
Check with the customer to determine the integrated LED/Valet switch location.
z
Remove the domelight fuse. This prevents accidentally draining the battery.
z
Roll down a window to avoid being locked out of the car.
after the install:
z
Test all functions. The “Using Your System” section of the Owner’s Guide is very
helpful when testing.
z
When testing, don’t forget that this system is equipped with Nuisance Prevention® Circuitry.
NPC™ can bypass both sensor zones, making them seem to stop working.
z
Carefully reassemble the under-dash trim panels.
z
Inspect the engine compartment for tools that may have been left behind.
tools required
This is a general list of tools required to complete the installation of this security system in most vehicles. Some vehicles may require additional tools.
z
Digital multi-meter
z
Nutdriver and/or socket set
z
Wire cutters/strippers
z
Panel removal tool
4
© 2005 directed electronics, inc.
z
Solderless terminal crimpers
z
Drill bit set
z
Cordless power drill
z
Phillips head screwdriver
z
Torx driver set
z
Work light
deciding on component location
control module
Never put the control module in the engine compartment!
The first step in hot-wiring a vehicle is removing the driver's side underdash panel to
access the starter and ignition wires. If the control module is placed just behind the
driver's side dash it can easily be disconnected.
When locating the control module, try to find a secure location that will not require
you to extend the harnesses’ wires (they are 1.5 meters long). Keep it away from the
heater core (or any other heat sources) and any obvious leaks.
Some good control module locations: Above the glove box, inside the center console,
above the underdash fuse box, above the radio, etc.
© 2005 directed electronics, inc.
5
integrated LED/Valet® switch
Things to remember when positioning the integrated LED/Valet® switch:
•
It should be visible from both sides and the
rear of the vehicle, if possible.
•
It needs at least 1-1/2" clearance to the rear.
•
It is easiest to use a small removable panel,
such as a switch blank or a dash bezel.
Remove it before drilling your 5/16" hole.
IMPORTANT! Do NOT use a step drill bit (unibit) for drilling the 5/16” hole. It is recommended to use a 5/16” drill bit. Use care to ensure the hole is drilled straight.
Drilling at an angle can cause product malfunction.
starter kill relay
If the Starter Kill Relay or it’s connections are immediately visible upon removal of the
underdash panel, they can easily be bypassed. Always make the relay and its connections difficult to discern from the factory wiring! Exposed yellow butt connectors do
not look like factory parts, and will not fool anyone! For this reason, routing the starter
kill wires away from the steering column is recommended.
connecting your wires
Now that you have decided where each component will be located, you’re going to
find the wires in the car that the security system will be connected to.
IMPORTANT! Do not use a 12V test light to find these wires! All testing described in
this manual is described using a digital multimeter.
obtaining constant 12V
We recommend two possible sources for 12V constant: The (+) terminal of the battery,
or the constant supply to the ignition switch. Always install a fuse within 12 inches of
this connection.
6
© 2005 directed electronics, inc.
IMPORTANT! Do not remove the fuse holder on the red (H1/11) wire. It ensures that
the control module has it’s own fuse, of the proper value, regardless of how many
accessories are added to the main power feed.
finding the 12V switched ignition wire
The ignition wire is powered when the key is in the run or start position. This is
because the ignition wire powers the ignition system (spark plugs, coil) as well as the
fuel delivery system (fuel pump, fuel injection computer). Accessory wires, on the other
hand, lose power when the key is in the start position to make more current available
to the starter motor. Use the following procedure to find (+)12V with your multimeter.
1.
Set to DCV or DC voltage (12V or 20V is fine).
2.
Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the ignition wire.
The steering column harness or ignition switch harness is
an excellent place to find this wire.
4. Turn the ignition key switch to the run position. If your
meter reads (+)12V, go to the next step. If it doesn’t, probe
another wire.
5. Now turn the key to the start position. The meter display should stay steady, not dropping by more than a few
tenths of a volt. If it drops close to or all the way to zero,
go back to step 3. If it stays steady at (+)12V, you have
found an ignition wire.
© 2005 directed electronics, inc.
7
finding a parking light wire
The parking light wire is often found near the switch. Many cars have the switch built
into the turn signal lever, and in these cars the parking light wire can be found in the
steering column. The same wire is often available in the kick panel or running board.
(+) parking light wire
Use the following procedure to find (+) parking light wire with your multimeter.
1.
Set to DCV or DC voltage (12V or 20V
is fine).
2.
Attach the (-) probe of the meter to
chassis ground.
3.
Probe the wire you suspect of being the
parking light wire. Usually, the area
near the headlight/parking light switch
is an excellent area to start, as is the
kick panel.
4.
Turn on the parking lights. If your meter shows (+)12V, turn off the parking lights
and make sure it goes back to zero.
5.
If it does return to zero, turn the parking lights back on and, using the dash light
dimmer control, turn the brightness of the dash lights up and down. If the meter
changes more than a volt when using the dimmer, look for another wire. If it
stays relatively close to (+)12V, you have found your parking light wire.
(-) parking light wire
Use the following procedure to find (-) parking light wire with your multimeter.
1.
Set to DCV or DC voltage (12V or 20V
is fine).
2.
Attach the (+) probe of the meter to
+12V.
3.
Probe the wire you suspect of being the
parking light wire. Usually, the area
near the headlight/parking light switch
is an excellent area to start, as is the
kick panel.
8
© 2005 directed electronics, inc.
4.
Turn on the parking lights. If your meter shows (+)12V, turn off the parking lights
and make sure it goes back to zero.
5.
If it does return to zero, turn the parking lights back on and, using the dash light
dimmer control, turn the brightness of the dash lights up and down. If the meter
changes more than a volt when using the dimmer, look for another wire. If it
stays relatively close to (+)12V, you have found your parking light wire.
finding the door pin switch circuit
The best places to find the door switch wire are:
At the pin switch: When testing at the pin switch, check the wire to ensure that it “sees”
all the doors. Often, the passenger switch will cover all the doors even if the driver’s
switch will not.
At the dome light: This may not be your best choice if the vehicle has delayed domelight
supervision, but it will work in vehicles with completely diode-isolated pin switches.
Often the door switch wires, described above, can also be found in the windshield pillars, running boards or kick plates.
Use the following procedure to find the door pin switch wire with your multimeter.
1.
Set to DCV or DC voltage (12V or 20V is fine).
2.
In most cars, fasten the (+) probe of your meter to (+)12V constant.
3.
Probe the wire you suspect of being the door trigger wire. If the meter reads
(+)12V when any door is opened and the meter goes to 0 with the door closed,
you have found a trigger wire.
NOTE: Make sure the wire you use “sees” all the doors! Some newer vehicles lack
standard-type pinswitches. The dome light in these vehicles is turned on when the door
handle is lifted. These usually have a wire coming out of the door into the kick panel
which will provide a (-) trigger for all doors.
© 2005 directed electronics, inc.
9
main harness wire connection guide
main harness wiring diagram
H1/1
___ ORANGE
H1/2
___ WHITE
H1/3
___ WHITE/BLUE
H1/4
___ BLACK/WHITE
H1/5
___ GREEN
H1/6
___ BLUE
H1/7
___ VIOLET
H1/8
___ BLACK
H1/9
___ YELLOW
(+) Ignition Input
H1/10
___ BROWN
(+) Siren Output
H1/11
___ RED
H1/12
___ RED/WHITE (-) 200mA Auxiliary Channel/Delayed Accessory Output
(-) 500mA Ground When Armed
(+)/(-) Light Flash Output
No Function
(-) 200mA Domelight Supervision Output
(-) Door Trigger Input
(-) Instant Trigger (Hood and Trunk Pin)
(+) Door Trigger Input
(-) Chassis Ground Input
(+) 12V Constant Power Input
main harness wiring guide
H1/1 ORANGE (-) 500 mA ground-when-armed output: This wire supplies a (-)
ground as long as the system is armed. This output ceases as soon as the system is
disarmed. This wire controls operation of the pre-wired starter kill relay and can be
used to control other optional accessories.
NOTE: If connecting the orange wire to control another module, such as a 529T or
530T window controller, a 1 amp diode (type 1N4004) will be required. Insert the
diode as shown below.
10
© 2005 directed electronics, inc.
IMPORTANT! Never interrupt any wire other than the starter wire.
H1/2 WHITE light flash output: As shipped, this wire should be connected to the (+)
parking light wire. It will supply a (+) 10A output. If the light flash polarity fuse jumper
inside the unit is moved to the opposite position (see Internal Jumpers), this wire supplies a (-) 10A output. This is suitable for driving (-)parking light wires.
LIGHT BULB
(+) 12V
WHITE H1/2
(-) LIGHT FLASH OUTPUT
PARKING LIGHT
RELAY OR SWITCH
© 2005 directed electronics, inc.
11
H1/3 WHITE/BLUE no function.
H1/4 BLACK/WHITE (-) 200 mA domelight-supervision output: Connect this wire to
the optional domelight supervision relay.
IMPORTANT! This output is only intended to drive a relay. It cannot be connected
directly to the domelight circuit, as the output cannot support the current draw of one
or more bulbs.
H1/5 GREEN (-) door trigger input: Most vehicles use negative door trigger circuits.
Connect the green wire to a wire which shows ground when any door is opened. In
vehicles with factory delays on the domelight circuit, there is usually a wire that is
unaffected by the delay circuitry.
12
© 2005 directed electronics, inc.
H1/6 BLUE (-) instant trigger: This input will respond to a negative input with an
instant trigger. It is ideal for hood and trunk pins and will report on zone one.
H1/7 VIOLET (+) door trigger input: This wire is used in vehicles that have a positive
(+) switched dome light circuit . Connect the violet wire to a wire that shows (+)12V
when any door is opened, and ground when the door is closed.
H1/8 BLACK (-) chassis ground connection: Connect this wire to bare metal,
preferably with a factory bolt rather than your own screw. Screws tend to either
strip or loosen with time. All components, should be grounded to the same point
in the vehicle if possible.
H1/9 YELLOW (+) ignition input: Connect this wire to the (+)12V ignition wire. This
wire must show (+)12V with the key in Run position and during cranking. Take care
to insure that this wire cannot be shorted to the vehicle chassis at any point.
© 2005 directed electronics, inc.
13
H1/10 BROWN (+) siren output: This output can be used if an optional siren is
installed. Connect this to the RED wire of the siren. Connect the BLACK wire of the
siren to (-) chassis ground, preferably at the same point as the control module’s BLACK
ground wire.
H1/11 RED (+)12V constant power input: Before connecting this wire, remove the
supplied fuse. Connect to the battery positive terminal or the constant 12V supply to
the ignition switch.
NOTE: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not
use the 15A fuse in the harness for this purpose. This fuse protects the module itself.
H1/12 RED/WHITE (-) 200mA auxiliary channel/delayed accessory output: If programmed for an auxiliary output, this wire will provide a (-) pulse when the lock button on the factory transmitter is pressed twice within three seconds. This output can be
used to control optional accessories. If programmed for delayed accessory output, this
wire will provide (-) ground when the ignition is turned off and will continue to output
(-) ground until a door is opened then closed. This can be used to energize the accessory circuit in the vehicle to keep the radio and other accessories on after the ignition
is turned off.
IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!
This transistorized output can only supply (-) 200 mA, and connecting directly to a solenoid, motor, or other high-current device will cause the module to fail.
NOTE: Sensors and other triggers can be bypassed if this output is used to open the
vehicle trunk while the alarm is armed. See H2/5 Gray zone shunting for programming and connection descriptions.
14
© 2005 directed electronics, inc.
auxiliary harness wire connection guide
auxiliary harness wiring diagram
H2/1
___ BROWN
(-) Horn Honk Output
H2/2
___ GREEN
Arm Input
H2/3
___ RED
H2/4
___ BLUE
Disarm Input
H2/5
___ GRAY
(+) Trunk Release/Sensor Shunt Input
H2/6
___ VIOLET/BLACK
H2/7
___ YELLOW/BLACK
Disarm Defeat Input
No Function
Light Flash Monitor Input
auxiliary harness wiring guide
H2/1 BROWN (-) horn honk output: This wire supplies a 200 mA (-) output that can
be used to honk the vehicle’s horn. It provides a pulsed output when the security system is armed/disarmed and in the triggered sequence or in panic mode. In most vehicle’s with (-) horn circuits this wire can control the vehicle’s horn without adding a
relay. If the vehicle has a (+) horn circuit, an optional relay must be used to interface
with the vehicle’s horn circuit.
IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!
This transistorized output can only supply (-) 200 mA, and connecting directly to a solenoid, motor, or other high-current device will cause the module to fail.
H2/2 GREEN for arm input: Connect this GREEN wire to a wire that changes state when
the doors are locked using the factory keyless entry transmitter. This wire can accept a
positive (+) or negative (-) input. The vehicle’s power door lock motor wire is ideal.
H2/3 RED disarm defeat input: This wire is used to prevent the interior door lock
switches from disarming the system. To determine the best location to interface this
wire, first test the operation of the remote keyless entry system. When unlocking the
doors with the factory remote transmitter, does the driver’s door unlock first? Most
© 2005 directed electronics, inc.
15
vehicles operate this way. If this is the case connect the RED wire to the passenger
unlock motor wire. When testing this wire be sure that it shows 12V (+) ONLY when
the unlock button on the factory transmitter is pressed the second time to unlock the
passenger doors. If the factory keyless entry system unlocks all of the doors at the
same time, it is recommended that the H2/7 YELLOW/BLACK wire be used for disarm defeat input.
NOTE: The H2/3 wire connection is not required if using H2/7 YELLOW/BLACK as a
disarm defeat wire.
H2/4 BLUE disarm input: Connect the BLUE wire to a wire that changes state when the
doors are unlocked using the factory keyless entry transmitter. If the factory transmitter
unlocks the driver’s door first, the BLUE wire must be connected to the wire that changes
state when the driver’s door is unlocked by itself. In this case, find the driver’s door
unlock motor wire. In most vehicle’s this wire can be found in the driver’s kick panel.
NOTE: Some vehicles (some models of the Honda, GM and Ford) have long door
lock pulses. These long pulses may interfere with the disarm function of this system
when unlocking all doors using the factory OEM remote. Use the supplied door unlock
pulse adapter for these vehicles. Refer to the diagram below.
DOOR UNLOCK
PULSE ADAPTER
DIODE
0.47 mF
POLARIZED
CAP 25V
OR
HIGHER
+
CONTROL MODULE
-
UNLOCK MOTOR
WIRE
BLUE/WHITE
BLUE - DISARM WIRE
6.2 MΩ
RESISTOR
(BLUE-REDGREEN-SILVER
OR GOLD)
WHITE/BLUE
BLACK/WHITE
H2/5 GRAY trunk release/sensor shunt input: This input is used to bypass the sensor
inputs when the trunk is opened using the factory keyless entry system or trunk release
relay while armed. When the system receives a (+) input on this wire, zones 1, 2 and
4 are bypassed for 3-seconds. If during that 3-seconds, ground is applied to the H1/6
16
© 2005 directed electronics, inc.
BLUE wire then the alarm zones are bypassed (See Feature menu 1/8) and will
remain bypassed until the ground input is removed. This means that when the trunk is
open with the factory transmitter the only triggers that remain active while the trunk is
open are the doors and ignition. 3-seconds after the trunk is closed the bypassed
zones again become active.
H2/6 VIOLET/BLACK no function.
H2/7 YELLOW/BLACK light flash monitor input: This input monitors the factory system light flash output and can be used as a disarm defeat wire. Connect this wire to
the light flash wire that flashes when the factory transmitter is used. This may be a status LED, parking lights, reverse lights, etc., depending on the vehicle type and manufacturer. This wire can accept a (+) positive or (-) negative input.
keyless entry systems—three types
There are three main types of keyless entry systems. Systems that unlock the driver’s
door first and have internal relays, systems that unlock the driver’s door first but have
external relays, and systems without driver’s priority door unlock.
factory remote—driver’s door unlock
© 2005 directed electronics, inc.
17
external relays—driver’s door unlock
This system is used in many four-door GM sedans. To test for this type of system, probe
the unlock wire from the interior switch (black or white). Unlock the driver’s door, by
itself, using the factory remote. If the switch wire shows (+) 12V, then use the following diagram:
NOTE: It is often easy to access the passenger unlock wire going to the rear door
motor on the driver’s side.
18
© 2005 directed electronics, inc.
no priority—driver’s door unlock
This type of keyless entry system is common in import vehicles as well as many Jeep
vehicles. When unlocking the doors with the transmitter all doors unlock at the same
time. It is recommended to use H2/7 YELLOW/BLACK wire for Disarm Defeat instead
of the H2/3 RED wire. This input wire monitors the factory system light flash output.
Connect this wire to the light flash wire that flashes when the factory transmitter is
used. This may be a status LED, parking lights, reverse lights, etc., depending on the
vehicle type and manufacturer. Do NOT connect this wire to the domelight. This wire
can accept a (+) positive or (-) negative input.
For installation, please refer to the diagram below.
PARKING LIGHT BULB
PARKING LIGHT RELAY
OR SWITCH
H2/7 YEL/BLK
(NOT USED)
© 2005 directed electronics, inc.
19
door lock harness wire connection guide
These door lock outputs are for Passive arming control of the factory door locks.
They can also be used to control the door locks with the ignition switch for vehicle
that do not have this feature in the factory RKE system.
H3/A
___ GREEN
H3/B
___
H3/C
___ BLUE
(-) Lock, (+) Unlock Output
Not Used
(-) Unlock, (+) Lock Output
The control module can control 2 common power door lock types without any additional parts. With certain vehicles, or if an actuator is to be installed, either a 451M Door
Lock Relay Satellite or two relays will be required. Refer to TechTips document 1041.
plug-in harnesses
integrated LED/Valet® switch
The integrated LED/Valet® switch should be accessible from the driver’s seat. The
Valet® part of the integrated LED/Valet® switch plugs into the blue port on the side of
the unit. Check for rear clearance before drilling a 5/16-inch hole and mounting the
switch. The LED part of the integrated LED/Valet® switch operates at 2V DC and plugs
into the white port on the side of the unit. Make sure the LED wires are not shorted to
ground as the LED will be damaged.
data port—Bitwriter®
The black three-pin port can be used for programming the unit using the Directed
Bitwriter, a hand held programming tool. The Bitwriter also allows programming of
features that are not available in the feature menus.
20
© 2005 directed electronics, inc.
four-pin optional sensor harness
RED wire
The red wire supplies constant power to the optional sensor.
BLACK wire
The black wire supplies ground to the optional sensor.
BLUE, GREEN wires
The blue and green wires are multiplex inputs. They are both tied to the same zone.
If an input of less than 0.8 seconds is supplied to either wire the Warn-Away®
response will occur. An input longer than 0.8 seconds to either wire will initiate the
triggered sequence and report zone 4. This port can be used for optional sensors such
as: the 506T—glass breakage sensor, or the 504D—field disturbance sensor.
dealer master control loop
This 2-pin black connector when removed in disarmed state from the control module will
reset the system back to allow the full set of customer settings and remove the dealer remote
from memory.
NOTE: For programming of dealer master remotes (Directed p/n 465D), the dealer master control loop MUST be plugged into the module.
door lock learn routine
Before the unit will respond to the factory remote keyless system, it must learn the
polarity of the door lock wires. To learn the lock polarity:
NOTE: It is important that all the INPUT signals to the control module are in the rest status state (no activity) before entering the learn routine.
© 2005 directed electronics, inc.
21
to learn lock:
NOTE: Make sure the doors, hood and trunk are closed so the factory RKE system operates as it would when the user is using it.
1. With all the doors, hood and trunk closed: Press and HOLD the integrated
LED/Valet® switch.
2. Within 5-seconds: Turn the ignition On and then Off (leave for less than 2-seconds
in the on position).
3. Within 5-seconds: Release the integrated LED/Valet® switch.
4. Within 5-seconds: Press and release the integrated LED/Valet® switch once.
5. Within 5-seconds: Press and HOLD the integrated LED/Valet® switch. The LED will
flash to indicate that the lock routine is ready to be learned.
6. Press lock button: Press the lock button on the factory transmitter. Wait for the LED
to illuminate to indicate the the lock learn was successful. If the learn was unsuccessful the LED would continue to flash.
7. Release the integrated LED/Valet® switch. Now advance to the learn Unlock routine.
to learn unlock:
1. Within 5-seconds of the learn lock routine (step 7), press and release the integrated LED/Valet® switch once.
2. Within 5-seconds: Press and HOLD the integrated LED/Valet® switch. The LED will
flash in groups of two flashes to indicate that the unlock routine is ready to be learned.
3. Press unlock button: Press the unlock button on the factory transmitter. The LED will
illuminate for a maximum of 5-seconds to indicate that the unlock learn was successful. If the learn was unsuccessful the LED would continue to flash in groups of two.
4. Release the integrated LED/Valet® switch.
22
© 2005 directed electronics, inc.
NOTE: If the Unlock learn was unsuccessful, the Unlock procedure can be repeated
by using the LOCK learn procedure, except that at step 4 press and release the integrated LED/Valet® switch TWICE. (The LED will flash in groups of two flashes.)
to exit the learn routine:
Do one of the following:
z
Turn the ignition on.
z
No activity for longer than 15 seconds.
z
Press the integrated LED/Valet® switch too many times.
on-board dual stage shock sensor
Less Sensitive
More Sensitive
There is a dual-stage shock sensor inside the control module. Adjustments are made via
the rotary control as indicated above. Since the shock sensor does not work well when
mounted firmly to metal, we recommend against screwing down the control module. The
full trigger of the onboard shock sensor reports zone 2. See Table of Zones.
NOTE: When adjusting the sensor, it must be in the same mounting location that it will
be after the install is completed. Adjusting the sensor and then relocating the module
requires readjustment.
© 2005 directed electronics, inc.
23
internal programming jumper
A 10A fuse is used as both a fuse and a program jumper. This jumper determines the
light flash output polarity. In the (+) position, the on-board relay is enabled and the
unit will output (+)12V on the WHITE wire, H1/2. In the (-) position, the on-board
relay is enabled for (-) output on the WHITE wire, H1/2. To access the jumper, remove
the sliding door from on top of the control module, as shown below.
FUSE/JUMPER
(-) POSITION
FUSE/JUMPER
(+) POSITION
zones
Zone
Trigger Type
Number
Input Description
1
Instant trigger
Hood and/or trunk pin switches.
2
Multiplexed input
Heavy impact from on-board
Doublegurard® shock sensor.
3
Two-stage, progresses from warning Door switch circuit.
to full alarm
4
Multiplexed
Optional sensor, Inputs shorter than
0.8 seconds will trigger Warn Away®
response, while inputs longer than
0.8 seconds will instantly trigger full
alarm.
5
Two-stage (similar to zone 3)
Ignition input.
NOTE: The Warn Away® response does not report on the LED.
24
© 2005 directed electronics, inc.
long term event history
The control module will store the last 2 triggers in memory that are not erased when
the ignition is turned on. This can be helpful for trouble shooting false alarm reports.
To access the event history use the following procedure.
1. Turn the ignition switch off and press and hold the integrated LED/Valet® switch.
2. While holding the integrated LED/Valet® switch turn the ignition On.
3. Release the integrated LED/Valet® switch.
4. Within 5-seconds, press and release the integrated LED/Valet® switch.
The LED will flash in groups indicating the last two zones reported triggered. For
example, if zone 2 and 3 were the last two zones to be triggered, the LED will flash
two times followed by a pause and then flash three times followed by a pause.
NOTE: The Warn Away® response does not report on the LED.
The Long Term Event History will exit if the ignition is turned off or there is no activity
for 60-seconds.
rapid resume logic
The current state of the alarm will be stored in non-volatile memory. If power is lost
and then reconnected, the system will recall the stored state from memory (arm, disarm, and Valet® mode).
© 2005 directed electronics, inc.
25
feature programming
The feature programming routine is used to access and change any of the feature settings in the two menus below. The feature settings can be accessed and changed by
using one of the following:
z
The integrated LED/Valet® switch to enter the feature programming routine.
z
Use of the Directed Electronics Bitwriter® is recommended. Expanded programming options are only available when using the Directed Electronics Bitwriter®.
NOTE: If Feature Programming Lockout is set to ON, all features will be locked and
can ONLY be accessed by using a Bitwriter®.
to enter feature programming routine
1. Open a door.
2. Turn the ignition on and then off.
3. Close the door.
4. Within 5-seconds, press and HOLD the integrated LED/Valet® switch. After 3-seconds the horn will sound once to indicate entry into the first features menu. To select
the second features menu, continue to hold the integrated LED/Valet® switch until the
horn sounds twice. Once the desired menu is selected, release the integrated
LED/Valet® switch.
5. Within 5-seconds, press and release the integrated LED/Valet® switch the number
of times corresponding to the desired feature listed below. Then press the integrated
LED/Valet® switch one more time and hold. The horn will sound the number of times
equal to the feature number selected.
6. While holding the integrated LED/Valet® switch, assign the selected feature to a factory button by either pressing Lock for 1 short horn honk setting or pressing Unlock
for 2 short horn honk setting.
26
© 2005 directed electronics, inc.
once a feature is programmed
z
Another feature(s) can be programmed.
z
The other feature menu can be selected.
z
The Learn Routine can be exited.
accessing another feature
z
Release, then press and release the integrated LED/Valet® switch the number of
times to advance from the feature just programmed to the next feature desired.
z
Press and hold the integrated LED/Valet® switch once more.
z
The horn will chirp to confirm the feature selected.
accessing another menu
z
Release, then press and release hold the integrated LED/Valet® switch.
z
After 3-seconds, the unit will advance to the next menu and the horn will sound
2 times to indicate feature menu 2 has been entered.
exiting feature programming
z
Open the door.
z
Turn the ignition On.
z
No activity for 15-seconds.
z
Press and release the integrated LED/Valet® switch too many times.
© 2005 directed electronics, inc.
27
Bitwriter® ONLY features
Due to memory limitations for this system, the following features can only be programmed using Directed’s Bitwriter® programmer. Factory default settings are shown
in bold.
28
B-1
Forced passive arming ON
Forced passive arming OFF
B-2
NPC ON
NPC OFF
B-3
Panic with ignition ON
Panic with ignition OFF
B-4
Dealer security features ON
Dealer security features OFF
B-5
Transmitter programming UNLOCKED Transmitter programming LOCKED
B-6
Feature programming UNLOCKED
B-7
Siren duration — 0 to 180 seconds programmable
Feature programming LOCKED
© 2005 directed electronics, inc.
features #1 menu
Factory default settings are shown in bold.
Feature
Lock Button (one chirp)
Step
Unlock Button (two chirps)
1
Active arming
Passive arming
2
Chirps ON
Chirps OFF
3
Door Trigger Error Chirp ON
Door Trigger Error Chirp OFF
4
Ignition-Controlled Domelight ON Ignition-Controlled Domelight OFF
5
Panic Enabled (OEM upgrade)
Auxiliary Output Enabled (OEM upgrade)
6
Auxiliary Output
Delayed Accessory Output
7
Delayed Door Trigger
Instant Door Trigger
8
Sensor shunt zones 1, 2 & 4
All zones
9
Siren Duration–30 seconds
Siren Duration–60 seconds
10
Valet® switch input: 1-pulse
Valet® switch input: 2-5 pulses
11
Horn pulse honk duration 0.020
seconds (does not affect full trig- 0.030, 0.040, 0.050 seconds
ger pulse duration)
Feature steps 5 and 6 are related. Only if Auxiliary Output Enabled is selected in feature 5 can either Auxiliary Output or Delayed Accessory Output be selected in feature step 6. Examples of this are where Auxiliary Output is used to provide a momentary 800mSec pulse on the RED/WHITE wire of the main harness (can be used for
opening the trunk). The delayed accessory output is used to allow selected vehicle
accessories to remain on (such as radio) when the ignition is turned off. This output
will remain active for 1 hour until a door is opened and closed, or the system is armed
using the factory remote transmitter.
© 2005 directed electronics, inc.
29
features #2 menu
Factory default settings are shown in bold.
NOTE: Feature step number 6 and 7 are not applicable to the this model.
Feature
Lock Button (one chirp)
Step
30
Unlock Button (two chirps)
1
Ignition-Controlled Locking ON
Ignition-Controlled Locking OFF
2
Ignition-Controlled UnLocking ON Ignition-Controlled Unlocking OFF
3
Active Locking
4
Door Lock Pulse Duration–0.8 sec. Door Lock Pulse Duration–3.5 sec.
5
Single Unlock Pulse
Double Unlock Pulse
6
Channel 3: Validity
Channel 3: Second Unlock
7
Code Hopping ON
Code Hopping OFF
Passive Locking
© 2005 directed electronics, inc.
master dealer remotes
A master dealer remote can be programmed into the system for demonstration purposes. Generally, each salesman would carry a remote that would operate all the cars
on the lot equipped with this system. The dealer remotes are binary transmitters that
are detuned slightly in order to limit transmitting range. The dealer remote can be
taught to the system by the following Transmitter Learn Routine.
master dealer remote learn routine
Since the OEM UPGRADE SECURITY SYSTEM does not ship with a receiver, programming
of the Master Dealer Remote (Directed P/N: 465D) requires the following conditions:
z
Receiver (Directed P/N: 543R and 543B) must be plugged into the 4-pin
receiver port.
z
2-pin Dealer Master Loop (Included) must be plugged into the BLACK 2-pin
Loop port.
NOTE: Refer to Wiring Quick Reference Guide at the back of this guide for port locations.
To program the Master Dealer Remote to the OEM UPGRADE SECURITY SYSTEM:
1. Open a door.
2. Key. Turn the ignition on.
3. Choose. Within 5-seconds, press and release the integrated LED/Valet® switch the
number of times corresponding to the desired channel listed below. Once you have
selected the channel, press the switch once more and HOLD it. The LED will flash and
the horn will honk (if connected) to confirm the selected channel. Do not release the
integrated LED/Valet® switch.
4. Transmit. While holding the integrated LED/Valet® switch, press the button from the
transmitter that you wish to assign to the selected channel. The unit will chirp indicating successful programming. It is not possible to teach a transmitter button to the system more than once.
© 2005 directed electronics, inc.
31
5. Release. Once the transmitter is learned, the integrated LED/Valet® switch can be released.
Channel Number
Function
Wire Color
1
Auto learn standard configuration
N/A
2-8
No Function for Dealer Master Remote
N/A
9
Delete all transmitters
N/A
When installing the system, it is possible to preset all of the operation settings using
the master dealer remote. However, when the system is operated using the master
dealer remote, a special set of dealer default settings are followed. The dealer default
settings are used to ensure that every vehicle equipped with this system is protected at
all times. All system features can be programmed to meet the installation needs but
only the settings listed below will be affected in master dealer mode.
z
Passive arming On
z
Confirmation honks off
z
Ignition lock and unlock on (if installed)
z
Passive locking (if programmed on) (“Default setting ON for Dealer
Master Mode” for passive locking.)
z
Ignition domelight on
z
Security features off (Programmable with Bitwriter)
z
Valet® mode disabled
These features will be set as listed and will remain so (Except Security Features) until
the master dealer mode is exited. Once the vehicle is delivered to the end user, the
dealer master loop harness should be removed. The system will then operate according to how the operating settings have been preset. It is also possible to reprogram
the operating settings by following the feature programming section of this guide.
32
© 2005 directed electronics, inc.
troubleshooting
starter kill does not work:
z
Is the correct starter wire being interrupted? If the car starts when the starter kill relay
is completely disconnected, the wrong starter wire has been cut and interrupted.
•
Is the yellow wire connected to “true” ignition? Make sure this wire is connected
to a wire that has power in the run and start positions.
the Valet® switch does not work.
•
Is it plugged into the correct socket? See the integrated LED/Valet® Switch section.
•
Is the H1/9 YELLOW wire properly connected? See Primary Harness (H1) Wire
Connection Guide section of this guide.
•
Was the correct hole size drilled (5/16”). See Integrated LED/Valet® switch section of this guide.
status LED does not work.
•
Is the LED plugged into the small white port on the side of the control unit? See
integrated LED/Valet® Switch section. See Integrated LED/Valet® switch section
of this guide.
Passive or Ignition controlled door locks operate backwards.
•
This unit has easily-reversed lock/unlock outputs. Recheck Harness 3, (+/-) Door
Lock Outputs section to see if you have reversed these.
the horn honks when the unit enters panic mode, but the confirmation honks do not work when locking and unlocking.
•
Are the confirmation honks turned on in programming? See Operating Settings
Learn Routine and Feature Descriptions sections.
•
Is the unit in Valet mode.
© 2005 directed electronics, inc.
33
I can get into programming and change the feature settings,
but when I use the remote the settings seem to change.
•
Are you using a binary, master dealer remote? Remember, you can program the
settings using a master dealer remote. However, the unit will follow the dealer
default settings when using a binary remote to operate the system.
Door Lock Learn Routine does not learn door locks.
•
Check connections to be sure everything is properly connected. Refer to the Keyless
Entry Systems—Three Types section of this guide for correct wire connections.
•
Check the Door Lock Learn Routine section of this guide to ensure the correct procedure is being used.
Door Lock Learn Routine does not work, the unit enters the
learn routine then chirps horn and exits.
•
Some cars do not flash the parking lights with the door open. For these vehicles,
to program the unit correctly the door needs to be closed (so that the parking lights
will flash with the factory keyless system).
Unit does not learn Dealer Master Remote.
•
Please refer to the Master Dealer Remotes section of this guide. The following two
conditions must be met in order to learn a master remote:
•
A receiver (not included (543B and 543R)) MUST be connected to the
system.
•
The Dealer Master Loop (included with the system) MUST be plugged in.
Unit goes into Programming every time the ignition is turned off.
•
34
The LED/Valet® switch is probably stuck in the down position. If the hole for the
switch is too tight, the travel of the switch can be impaired and the switch may stick
in the down position. To allow the button to travel freely, the mounting hole must
not be too tight.
© 2005 directed electronics, inc.
Feature Programming routine does not work, the unit enters the
learn routine then chirps and exits.
•
Check the Door Input connections. If the dome light is used for door trigger input,
then the dome light must turn off in step 3.
© 2005 directed electronics, inc.
35
36
© 2005 directed electronics, inc.
Integrated
LED/Valet®
Switch
© 2005 directed electronics, inc.
BLUE Plug
Valet® Switch
BLACK (-) Chassis ground connection
YELLOW (+) Ignition input
BROWN (+) Siren output (optional)
RED (+) 12V Constant power
RED/WHITE (-) 200mA Auxiliary Channel/
Delayed Accessory Output
To WHITE
Plug (LED)
Receiver
(not used)
BLACK
Dealer
Master
Loop
Optional Sensor Input
RED (+) 12V
BLACK common
BLUE Mux zone 4
GREEN Mux zone 4
WHITE
Plug (LED)
To Integrated
LED/VALET Switch
YELLOW/BLACK Light flash monitor input
VIOLET/BLACK No function
GRAY (+) Trunk release/sensor input
BLUE Disarm input
RED Disarm defeat input
GREEN Arm input
BROWN (-) Horn honk output
GREEN (-) Lock, (+) Unlock
Empty
BLUE (-) Unlock, (+) Lock
VIOLET (+) Door trigger input
BLUE (-) Instant trigger
WHITE (+/-) Light flash output
WHITE/BLUE No function
BLACK/WHITE (-) 200mA Dome light supervision output
GREEN (-) Door trigger input
ORANGE (-) Ground-when-armed output
Optional
Bitwriter
wiring quick reference guide
37