Alpine DVA-5205P Owner`s manual

R
DVA-5205P
DVD/VIDEO CD/
CD PLAYER
• OWNER’S MANUAL (Page 2-71)
Please read this manual to maximize your
enjoyment of the outstanding performance and
feature capabilities of the equipment, then retain
the manual for future reference.
• MODE D’EMPLOI (Page 72-141)
Veuillez lire ce mode d’emploi pour tirer
pleinement profit des excellentes performances et
fonctions de cet appareil, et conservez-le pour
toute référence future.
• MANUAL DE OPERACION (Página 142-211)
Lea este manual, por favor, para disfrutar al
máximo de las excepcionales prestaciones y
posibilidades funcionales que ofrece el equipo,
luego guarde el manual para usarlo como
referencia en el futuro.
DIGITAL VIDEO
Precautions
Warning
This symbol means important instructions.
Failure to heed them can result in serious injury or death.
DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or
electric shock.
KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF THE REACH OF
CHILDREN. Swallowing them may result in serious injury. If swallowed, consult
a physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure
to do so may result in fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your
dealer if you are not sure.) Failure to do so may result in fire, etc.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY
FROM SAFELY DRIVING YOUR VEHICLE. Any function that requires your
prolonged attention should only be performed after coming to a complete stop.
Always stop the vehicle in a safe location before performing these functions.
Failure to do so may result in an accident.
DO NOT WATCH VIDEO WHILE DRIVING. Watching the video may distract the
driver from looking ahead of the vehicle and cause an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE
NOISE WHILE DRIVING. Failure to do so may result in an accident.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than
its designed application may result in fire, electric shock or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN INSERTION
SLOTS OR GAPS. Doing so may result in personal injury or damage to the
product.
DO NOT BLOCK VENTS OR RADIATOR PANELS. Doing so may cause heat to
build up inside and may result in fire.
2
Precautions
Caution
This symbol means important instructions.
Failure to heed them can result in injury or property damage.
DO NOT MIX NEW BATTERIES WITH OLD BATTERIES. INSERT WITH THE
CORRECT BATTERY POLARITY. When inserting the batteries, be sure to
observe proper polarity (+ and –) as instructed. Rupture or chemical leakage
from the battery may cause fire or personal injury.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may
cause personal injury or damage to the product. Return it to your authorized
Alpine dealer or the nearest Alpine Service Center for repairing.
3
Precautions
Temperature
Be sure the temperature inside the vehicle is between +60°C (+140°F) and –10°C
(+14°F) before turning your unit on.
Moisture Condensation
You may notice the CD playback sound wavering due to condensation. If this happens,
remove the disc from the player and wait about an hour for the moisture to evaporate.
Damaged Disc
Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc could
severely damage the playback mechanism.
Maintenance
If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine
dealer or the nearest Alpine Service Station for servicing.
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into the player by the
automatic reloading mechanism.
Do not attempt to insert a disc into the unit when the unit power is off.
Inserting Discs
Your player accepts only one disc at a time for playback. Do not attempt to load more
than one disc.
Make sure the label side is facing up when you insert the disc. Your player will automatically eject any disc that is inserted incorrectly.
Playing a disc while driving on a very bumpy road may result in skips, but this will not
scratch the disc or damage the player.
Irregular Shaped Discs
Make sure the discs you use in this unit do not have any irregularities. The outer and
inner edges should be round and smooth. Use of irregularly shaped discs may cause
damage to the mechanism.
New Discs
As a protective measure to prevent the CD from jamming, the CD player will automatically eject discs with irregular surfaces or inserted incorrectly. When a new disc is
inserted into the player and ejected after initial loading, using your finger, feel around
the inside of the centre hole and outside edge of the disc. If you feel any small bumps
or irregularities, this could inhibit proper loading of the disc. To remove the bumps, rub
the inside edge of the hole and outside edge of the disc with a ball-point pen or other
such instrument, then insert the disc again.
Installation Location
Make sure the DVA-5205P will not be installed in a location subjected to:
•
•
•
•
4
Direct sun and heat
High humidity and water
Excessive dust
Excessive vibrations
CONTENTS
Precautions
Warnings and Cautions ............................... 2
Contents ...................................................... 5
Custom setting –
Changing the Closed Caption setting .................... 35
Custom setting – Changing the Ai-NET settings .... 36
Custom setting –
Changing the H.U. Control settings ........................ 38
Quick Guide
About DVDs ................................................. 6
Discs playable on this DVD player ............... 7
When using remote control ......................... 8
Loading and unloading discs ....................... 9
Turning the power on and off ..................... 10
Switching between NTSC and
PAL configuration ....................................... 11
Adjusting the volume ................................. 11
Playing discs .............................................. 12
Stopping playback ..................................... 13
Fast-forwarding/fast-reversing ................... 14
Finding the beginnings of chapters or tracks .... 14
Playing still frames (pausing) ..................... 15
Frame-by-frame playback .......................... 15
Slow motion playback ................................ 15
Convenient Functions
Searching by title number .......................... 16
Searching directly by chapter or track number .. 17
Searching by elapsed time ........................ 18
Chapter/track/title repeat playback ............ 19
Switching the audio language ................... 19
Switching the angle ................................... 20
Switching the subtitles (subtitle language) ...... 20
Displaying the subtitles .............................. 21
Displaying the disc status .......................... 21
Video output ON/OFF ................................ 23
SET UP
Changing the Default Settings
Changing the default settings (setup) ........
Changing the language settings ................
Changing the TV screen settings ..............
Changing the country code setting ............
Setting the rating level (parental lock) .......
Changing the downsampling setting ..........
Changing the digital output setting ............
Changing the LED indicator setting ...........
24
24
26
27
28
30
32
34
Digital Audio Processor (Optional)
Operating the digital audio processor (optional) .... 40
Adjusting the parametric equalizer ............ 41
Adjusting the surround settings ................. 42
Storing the surround settings .................... 43
Recalling the surround settings ................. 44
Adjusting the time compensation .............. 45
Using the Pro Logic mode ......................... 45
ADJUST – Setting the speaker mode ........ 46
ADJUST – Adjusting the acoustic image ... 47
ADJUST – Mixing the rear audio channels ....... 48
ADJUST – Center speaker time compensation ..... 49
ADJUST – Rear speaker time compensation ... 50
ADJUST – Achieving powerful sound at low volumes .. 51
ADJUST – Adjusting the speaker level ...... 52
MODE – Adjusting the volume, fader and balance ..... 53
MODE – Adjusting the subwoofer ............. 54
MODE – Turning the defeat function on and off ..... 55
Operating from the Head Unit
(CDA-7865R)
Operating from the head unit ..................... 56
Operating from the head unit’s remote control unit ..... 58
Others
Terminology ...............................................
List of language codes ..............................
List of country codes .................................
In case of difficulty .....................................
Specifications ............................................
Functions of remote control unit buttons ...
60
61
63
66
67
68
5
About DVDs
About DVDs
Music CDs and DVDs have grooves (tracks) in
which the digital data is recorded. The data is
represented as microscopic pits recorded into
the track – these pits are read by a laser beam
to play the disc. On DVDs, the density of the
tracks and pits is twice that of CDs, so DVDs
can contain more data in less space.
• Multi angle function* (page 20)
When the DVD contains a movie shot from
multiple angles, the desired angle can be
selected from the remote control unit.
1.2 mm
DVDs
Minimum bit
length 0.9 µm
• Multiple audio* (page 19)
Movies can be recorded in up to eight
languages. The desired language can be
selected from the remote control unit.
• Subtitles function* (page 20)
Movies can include subtitles in up to 32
languages. The desired subtitle language
can be selected from the remote control unit.
CD-ROMs
Minimum bit
length 0.9 µm
Moreover, DVDs offer a variety of functions.
0.6 mm
0.6 mm
Track pitch • Multi story function*
1.6 µm
With this function, a single movie includes
various story lines. You can select different
story lines to view various versions of the
same movie.
Operation differs from disc to disc. Story line
selection screens including instructions
appear during the movie. Just follow the
instructions.
Track pitch 0.74 µm
Note: * The functions audio languages, subtitle
languages, angles, etc., differ from disc to
disc. For details, refer to the disc’s
instructions.
A 12 cm disc can contain one movie or about
four hours of music.
In addition, DVDs provide sharp picture quality
with vivid colors thanks to a horizontal resolution of over 500 lines (compared to less than
300 for VHS tape). With the addition of an
optional, digital audio processor (PXA-H510),
you can recreate the power and presence of a
movie theater with Dolby Digital 5.1-channel
Surround.
6
Discs playable on this DVD player
Discs playable on this DVD player
• Playable discs
The discs listed below can be played on this
DVD player. Other discs cannot be played.
Mark (logo)
Recorded
Max.
Disc size
playing time
content
One-sided
• DVD region number (playable region
number)
This DVD player will playback any disc whose
region number is 2 (or All). DVDs on which
you do not find a region number “2” or mark
“ALL” listed below, cannot be played on this
DVD player.
2
ALL
disc
Approx.
4 hours
12 cm*
Two-sided
disc
Approx.
Audio
8 hours
+
Video
DVD
(Moving
Video
One-sided
pictures)
disc
Approx.
80 Minutes
8 cm
Two-sided
disc
Approx.
160 Minutes
Audio
12 cm
+
Video
DIGITAL VIDEO
CD
(Moving
pictures)
8 cm
Audio
8 cm
(CD single)
*
Approx.
20 Minutes
12 cm
CD
74 Minutes
Video
VIDEO CD
Music
Approx.
Approx.
74 Minutes
Approx.
20 Minutes
Two-layer DVD disc compatible
• Discs that cannot not be played
DVD-ROMs, DVD-R/DVD-RAMs, CD-ROMs,
CD-R/CD-RWs, photo CDs, etc.
• Video CDs
This DVD player is compatible with playback
control (PBC) compatible video CDs (version
2.0).
“PBC” is a function by which you can use
menu screens recorded on the disc to find
the scene you want to watch and view
various types of information in dialog style.
• Disc terminology
Title
If titles are programmed for the DVD, these
are the largest unit of division of the information recorded on the disc.
Chapter
Each Title may also be divided into smaller
divisions called Chapters. These can be
specific scenes or musical selections.
* This product incorporates copyright
protection technology that is protected
by method claims of certain U.S. patents
and other intellectual property rights
owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be
authorized by Macrovision Corporation,
and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
* Manufactured under license from
Dolby Laboratories. “Dolby”, “Pro
Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
* “DTS” and “DTS Digital Out” are
trademarks of Digital Theater Systems, inc.
7
When using remote control
When using remote control
• Mode Switch
To operate the DVD Player, make sure
the mode switch is on “DVD”. DVD
operations are shown as the blue
characters on the remote control unit.
Replacing the batteries
Opening the battery cover
Push on the cover and slide it as
indicated by the arrows then the cover will
be removed.
DVD / AUDIO
Replacing the battery
Switching to “AUDIO” mode, makes it
possible to operate Alpine audio
products as well. Audio operations are
shown as the white characters on the
remote control unit.
• Point the remote control at the remote
sensor within about 2 meter.
• It may not be possible to operate the
remote control unit if the remote control
sensor is exposed to direct sunlight.
• The remote control is a small, light
weight precision device. To avoid
damage, short battery life, operational
errors and poor button response,
observe the following.
- Do not apply any shock.
- Do not put in a trouser pocket.
- Keep away from food, moisture and
dirt.
- Do not place in direct sunshine.
Remove the old batteries. Insert new
ones matching the (+) and (–) polarities
as shown in the diagram inside the
remote control.
-
+
+
Closing the cover
Push the cover in the arrow direction until
a click is heard.
Note: Use two AA size batteries.
Warning
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY
FROM SAFELY DRIVING YOUR VEHICLE. Any function that requires your
prolonged attention should only be performed after coming to a complete stop.
Always stop the vehicle in a safe location before performing these functions.
Failure to do so may result in an accident.
8
Loading and unloading discs
Loading and unloading discs
DVD Video CD
CD
Turn on the power before loading and unloading discs.
(Refer to page 10 “Turning the power on and off”.)
Loading discs
Press the door in gently then
slide it downwards.
POW
Close the door.
Be sure to close the door to prevent dust
from getting inside.
ER
OPEN
POW
ER
DVD
OPEN
DVD
Insert the disc with the side
containing words or diagrams
facing upwards.
Once the disc is partially inserted, it is
drawn in automatically. Playback starts.
Unloading discs
Press the door in gently then
slide it downwards. The disc is
automatically ejected part way.
DVD
If the disc is not removed, it is automatically drawn back into the player after a
while.
POW
ER
OPEN
Notes:
• If the ignition key is on ACC or ON, a disc can be
inserted even when the power is OFF. The power
then goes ON automatically.
• For two-sided DVDs, play one side of the disc to
the end, then unload the disc, turn it over and
reload it to play the other side.
Refer to the indications on the disc (“Side 1”/”Side
2”).
• Never insert map discs for navigation purposes
as they could damage the equipment.
• If wrong disc, upside-down discs or dirty discs
have been inserted, “DISC ERROR” is displayed.
Open the door and remove the disc.
DVD
Notes:
• If the ignition key is on ACC or ON, a disc can be
removed even when the power is OFF. After
removing the disc, the power goes OFF again
automatically.
• Even if you open the door, the disc will not be
ejected in the ACC OFF mode or in the disc
loading mode (“LOADING” is displayed).
close the door while the disc
Caution Never
is being unloaded. Doing so could
scratch the disc or damage the
player.
9
Turning the power on and off
N
LD
VO
Turning the power on
and off
VO
LU
P
Press “POWER”.
The power turns on.
POWER
NTSC/PAL
connected with an Alpine
Caution When
head unit
If the DVA-5205P is connected to
anything other than the CVA-1005R/IVAM700R/IVA-C800R (for ex.: CVA-1000R),
the default DVD setting must be
changed. See page 36, “Custom setting
– Changing the Ai-NET settings” to
change the SETUP to CD mode and see
page 38, “Custom setting – Changing
the H.U. CONTROL settings” to change
the SETUP to ON mode before using it.
POWER
To turn the power off, press
“POWER” again.
NTSC/PAL
Play Position Memory Function
• Even if you turn power off or switch the
Ignition Key to OFF during playback or
change the video source, playback will
continue from the point where playback
stopped when the power is turned ON
again.
The play position memory is released if
the disc is removed or the Reset switch
is pressed.
Notes:
• With this unit connected to an Ai-NET compatible
head unit, there will be about a 3 second delay during
power-up from the remote control. This is caused by
the systems communications being carried out by the
various components and is not a defect.
• When connected with an Ai-NET compatible head
unit, the power cannot be turned off from the remote
control unit. Turn off the DVA-5205P’s power by
switching the head unit’s source. For details, refer to
“Operating from the head unit” (page 56).
• Reading this manual
Tips
Stopping playback
Stopping
playback
These indicate the discs for which
the function can be used.
DVD Video CD
CD
Press the stop button during playback to stop
playback. That position is stored in the memory.
Press “ L ” during playback.
Tips
CHG
...DVDs
Video CD
...Video CDs
CD
...Music CDs
• Using the PRE-STOP function (DVD,
Video CD only)
When the PRE-STOP function is used, the
position at which playback is stopped is stored in
the memory, and playback resumes from that
position.
Press “ L ” once during playback.
“PRE-STOP” is displayed.
CHG
Press “ : ” in the PRE-STOP mode.
Playback starts from the position at which it
was stopped.
10
DVD
This indicates supplementary
explanation of operation of this
system.
Switching between NTSC and PAL configuration
Adjusting the volume
Switching between
NTSC and PAL
configuration
Adjusting the volume
Adjust the volume for connecting only
with the Digital Audio Processor (PXAH510).
Switch the video output configuration to
NTSC or PAL according to the type of
television and the disc recording method.
Press “NTSC/PAL” for
at least 5 seconds.
Move the rotary encoder to the
right or left.
Turn to the right to increase the volume.
Turn to the left to decrease the volume.
POWER
DN
VOL
NTSC/PAL
Notes:
• PAL is the standard and there is no need to
change the setting. The system is set to PAL at
time of shipment from the factory.
• The image output configuration must be correct.
Otherwise the following message appears and
playback does not start: “VIDEO SIGNAL
SYSTEM IS NOT CORRECT”.
VOL U
P
Note:If an Ai-NET product (head unit) has been
connected in addition to the Digital Audio
Processor (PXA-H510), or if this equipment is
connected singly to a TV monitor, adjust the
volume on the connected equipment.
DVD Video CD
• Using the Number Keys.
This describes use of the Number
Tips Keys, particularly the “+10” key.
CD
To input 10: Press the “+10” key once
and then press the “0” key.
To input 16: Press the “+10” key once
and then press the “6” key.
To input 23: Press the “+10” key twice
and then press the “3” key.
* Each time the “+10” key is pressed,
the number increases by 10.
11
Playing discs
Playing discs
DVD Video CD
CD
• With some DVDs, certain operations
Caution are disabled. Such operations are
ENT
DISP
MENU
SET
LIST
GO TO
TITLE
SOURCE
SLOW
CHG
not possible on such DVDs.
• The DVD functions described in this
manual are not supported by all
DVDs. See the individual DVDs
instructions for details on the
features supported.
• Fingerprints on a disc may
adversely affect playback. If a
problem occurs, remove the disc
and check for fingerprints on the
playback side. Clean the disc if
necessary.
• When using the remote control, be
careful to press one button at time.
Pressing multiple buttons at the
same time may cause erroneous
operation.
• Even if you switch the power or the
Ignition Key to OFF during playback
or change the video source,
playback will continue from the point
where it stopped when the power is
turned ON again.
If the disc is removed or the Reset
switch is pressed, the play position
memory is released.
Press “ : ”.
Playback starts.
SOURCE
SLOW
DVD Video CD
0 ∼ 9 、
UP
+10
• If a menu screen appears
On DVDs and video CDs with playback control
(PBC), menu screens may appear automatically. If this happens, perform the operation
described below to start playback.
Note: For many discs, the menu screen can also
be displayed by pressing “MENU” or “TITLE”
(for at least 2 seconds).
12
Stopping playback
DVD menu
Use the “Joystick” or the number keys (“0” to “9”
and “+10”) to select the desired item, then
press “ENT” or “ : ”.
1
2
4
ENT
5
6
8
0
or
Press “ L ” during playback.
9
OP/
CL
ENT
CD
Press the stop button during playback to stop
playback. That position is stored in the memory.
ANGLE
7
DVD Video CD
3
SUB T. ON/OFF. AUDIO
or
Stopping
playback
CHG
UP
+10
SOURCE
SLOW
Tips
• Using the PRE-STOP function (DVD,
Video CD only)
When the PRE-STOP function is used, the
position at which playback is stopped is stored in
the memory, and playback resumes from that
position.
Press “ L ” once during playback.
Note: For some discs it is not possible to select
items from the menu screen using the
number keys (“0” to “9” and ”+10”).
“PRE-STOP” is displayed.
CHG
Video CD menu
Use the number keys (“0” to “9” and ”+10”) to
select the desired number, then press “ENT” or
“ : ”.
1
2
Press “ : ” in the PRE-STOP mode.
Playback starts from the position at which it
was stopped.
3
SUB T. ON/OFF. AUDIO
4
5
SOURCE
SLOW
6
ANGLE
7
8
OP/
CL
0
9
UP
+10
•
Canceling the PRE-STOP function
Either press “ L ” again in the PRE-STOP mode
or eject the disc and turn the power or the ignition
key off to clear the memory.
ENT
or
SOURCE
SLOW
Notes:
• For some discs, the position at which playback
was stopped may not be accurate.
• Playback starts at the beginning of the disc
whenever ignition is turned off or another Ai-NET
source is selected.
Note: The menu screen does not appear when the
PBC function is turned off. If this is the
case, press “MENU” to turn on the PBC
function.
13
Fast-forwarding/fast-reversing
Finding the beginnings of chapters or tracks
Fast-forwarding/
fast-reversing
c
During playback,
press “ ” (fastreverse) or “ ”
(fast-forward) for
at least 2 seconds.
f
DVD Video CD
CD
A.PROC
DEFEAT
SOUR
CE
or
SLO
W
A. PROC
MUTE
RPT
DEFEAT
Press “ : ” to return to
normal playback.
SOURCE
SLOW
Notes:
• No sound or subtitles are played during fastforwarding/fast-reversing.
• For DVDs and video CDs with playback control
(PBC), the menu screen may reappear during
fast-forwarding/fast-reversing.
DVD
Finding the beginnings of chapters or tracks
c f
The chapter/track switches
During playback,
press“ ” or “
”.
each time the button is
pressed, and playback of
the selected chapter/track
starts.
Video CD
CD
A.PROC
DEFEAT
or
RPT
f: Press this to start playback from the
beginning of the following chapter or
track.
: Press this to start playback from the
beginning of the current chapter or
track.
c
14
Playing still frames (pausing)
Frame-by-frame playback
Slow motion playback
Frame-by-frame
playback
Note: Some DVDs do not have chapters.
Supplementary explanation
“Chapters” are divisions of movies or
musical selections on DVDs.
“Tracks” are divisions of movies or musical
selections on video and music CDs.
In the pause mode,
press “
”.
During playback,
press “
” once.
Press “ : ” to resume
playback.
Video CD
CD
MUTE
MUTE
The picture advances by
one frame each time the
button is pressed.
Press “ : ” to resume
normal playback.
DVD
Playing still
frames (pausing)
DVD
Video CD
SOURCE
SLOW
Note: No sound is played during frame-by-frame
playback.
Slow motion
playback
DVD
Video CD
During playback,
press “SLOW” for
at least 2 seconds.
SOURCE
SLOW
Press “ : ” to resume
normal playback.
SOURCE
SLOW
SOURCE
SLOW
Notes:
• No sound is played during the still frame mode.
• When a playback starts after about 5 minutes of
temporary still (pause), a picture or sound may
stop for an instant period, but this is not a failure.
Notes:
• During the slow motion playback, the playback
speed may change or the playback may skip to
the next picture depending on the disc, but this is
not a failure.
• No sound is played during slow motion playback.
• Slow playback is not available when playing back
a slide show.
15
Searching by title number
Searching by title
number
DVD
Use this function to easily find positions
on the DVD using the DVD’s title menu.
ENT
LIST
GO TO
TITLE
DISP
MENU
SET
During playback, press
“GO TO”.
LIST
GO TO
TITLE
The mode switches each
time the button is pressed.
Select “TITLE”.
BAND
RTN
T
U
V.O
TITLE
CHAPT
TIME
Normal playback
Input the number of the
title you want to play
using the number keys
(“0” to “9”).
1
2
3
SUB T. ON/OFF. AUDIO
4
5
6
ANGLE
7
8
9
OP/
CL
0
DN
CLR
(When title number 1 is input)
0
16
∼
9
Notes:
• This function cannot be used on discs on which
no title numbers are recorded.
• To input the title number, the “+10” key is not
used. Use the number keys “0” to “9”.
• Press “CLR” to delete the last digit in the title
number. Press “CLR” for at least 2 seconds to
clear all title numbers.
• Press “RTN” to cancel the title search mode and
resume normal playback.
Searching directly by chapter or track number
Press “ENT”.
Playback starts from the
selected title number.
ENT
DVD
Searching
directly by chapter
or track number
Video CD
CD
Notes:
• This function cannot be used on discs on which
no chapter numbers are recorded.
• To input the chapter or track number, the “+10”
key is not used. Use the number keys “0” to “9”.
• Press “CLR” to delete the last digit in the chapter/
track number. Press “CLR” for at least 2 seconds
to clear “Chapter” and “Track” numbers.
• Press “RTN” to cancel the chapter/track search
mode and resume normal playback.
• With video discs containing playback control
(PBC), function of “searching directly by track
number” is not available under the PBC ON
status. Press “MENU” to turn the PBC function off.
Press “ENT”.
Playback starts from the
selected chapter or track.
ENT
Use this function to easily move to the
beginnings of the chapters or tracks on the
disc.
During playback, press “GO TO”.
The mode switches each time the button
is pressed. Select “CHAPT” or “TRACK”.
LIST
GO TO
TITLE
DVD Video
TITLE
CHAPT
TIME
Normal playback
Video-CD/CD
TRACK
TIME
Normal playback
Input the number of the
chapter or track you
want to play using the
number keys (“0” to
“9”).
1
2
3
SUB T. ON/OFF. AUDIO
4
5
6
ANGLE
7
8
9
OP/
CL
0
(When chapter number 12 is input)
17
Searching by elapsed time
Searching by
elapsed time
DVD Video CD
CD
Use this function to search by specifying
the elapsed time.
During playback, press “GO TO”.
ENT
LIST
GO TO
TITLE
DISP
MENU
SET
BAND
The mode switches each time the button
is pressed. Select “TIME”.
LIST
GO TO
TITLE
RTN
T
U
V.O
DVD Video
RPT
DISC
TITLE
CHAPT
TIME
Normal playback
Video-CD/CD
TRACK
TIME
Normal playback
Input the elapsed time
from which you want to
start playback using the
number keys (“0” to
“9”).
1
2
3
SUB T. ON/OFF. AUDIO
4
5
6
ANGLE
7
8
9
OP/
CL
0
3
AUDIO
DN
CLR
(When 1 hour, 30 minutes is input as the
elapsed time)
0
18
∼
9
Notes:
• Input the hours first, followed by the minutes, then
the seconds.
• To input the elapsed time, the “+10” key is not
used. Use the number keys “0” to “9”.
• Press “CLR” to delete the last digit in the elapsed
time. Press “CLR” for at least 2 seconds to erase
all the set times.
• Press “RTN” to cancel the elapsed time search
mode and resume normal playback.
• With DVDs, the precision of the elapsed time
search function differs from disc to disc.
• With video discs containing playback control
(PBC), function of “searching by elapsed time” is
not available under the PBC ON status. Press
“MENU” to turn the PBC function off.
Chapter/track/title repeat playback
Switching the audio language
Press “ENT”.
Playback starts from the
specified elapsed time.
ENT
Switching the
audio language
DVD
Video CD
On DVDs including multiple audio modes or
multiple audio languages, the audio
language can be switched during playback.
During playback,
press “AUDIO” for
at least 2 seconds.
3
The sound switches
between the different
audio modes recorded on the
disc each time the button is
pressed.
Chapter/track/
title repeat
playback
DVD Video CD
CD
Use this function to play the disc’s titles,
chapters or tracks repeatedly.
During playback, press
“RPT”.
Notes:
• The language selected with the default settings is
set when the power is turned on or the disc is
replaced. If the disc does not include that
language, the disc’s default language is set.
• For some discs it is not possible to switch the
audio language during playback.
• Some time may be required for the audio
language to change.
RPT
DISC
The repeat mode switches
each time the button is
pressed.
DVD
Video CD
AUDIO
Chapter
The chapter is
played repeatedly.
Title
The title is
played repeatedly.
Repeat off
The mode returns
to normal playback.
(setting at factory
shipping)
• Video CDs with multiplex audio
During playback,
press “AUDIO” for
at least 2 seconds.
3
AUDIO
The combination of the
left and right channels
changes each time the button is
pressed.
LL
RR
LR
CD
Track
The track is
played repeatedly.
Disc
The entire disc is
played repeatedly.
Repeat off
(setting at factory
shipping)
Note: The track/disc repeat modes cannot be
used on video CDs with playback control
(PBC). Press “MENU” to turn the PBC
function off.
19
Switching the angle
Switching the subtitles (subtitle language)
Switching the angle
DVD
With DVDs on which images photographed from multiple angles are
recorded, the angle can be switched
during playback.
ENT
DISP
MENU
SET
LIST
GO TO
TITLE
SOURCE
SLOW
During playback, press
5
“ANGLE” for at least 2
seconds.
ANGLE
The angle switches between
the angles recorded on the disc
each time the button is pressed.
Notes:
• Some time may be required for the angle to
change.
• Depending on the disc, the angle may switch in
one of two ways.
- Seamless
: The angle switches smoothly.
- Non-seamless : When the angle is switched, a
still picture is displayed first,
after which the angle switches.
DISP.
TUNER
2
ON/OFF
1
Switching the
subtitles (subtitle
language)
DVD
With DVDs on which multiple subtitle
languages are recorded, the subtitle
language can be switched during playback.
SUB T.
5
ANGLE
During playback,
press “SUB T.” for
at least 2 seconds.
UP
0 ∼ 9 、 +10
1
SUB T.
The subtitle language
switches between the languages
recorded on the disc each time
the button is pressed.
Notes:
• Some time may be required for the subtitle
language to change.
• The language selected with the default settings is
set when the power is turned on or the disc is
replaced. If the disc does not include that
language, the disc’s default language is set.
20
Displaying the subtitles
Displaying the disc status
Displaying the
subtitles
DVD
Displaying the
disc status
DVD
With DVDs on which subtitles are recorded,
you can select whether to display the subtitles
or not during playback.
Use the procedure described below to display
the status (title number, chapter number, etc.) of
the currently playing DVD on the screen.
During playback,
press “– ON/OFF” for at 2
least 2 seconds.
ON/OFF
During playback, press DISP.
TUNER
“DISP.”.
The currently displayed
subtitles are turned on and off
each time the button is pressed.
Note: For some discs, the subtitles will be
displayed even when this is set to off.
The playback status is
displayed.
TV system (NTSC or PAL)
Operating mode
Current title
number
Current subtitle language
Current angle
number
•
Tips
Switching from the menu
For some discs, the audio language, angle and
subtitles can be switched from the disc menu.
Press “MENU” or “TITLE” (for at least
2 seconds), select the item, then
press “ENT”.
DISP
MENU
SET
or
LIST
GO TO
TITLE
ENT
Use the “Joystick” or the number
keys (“0” to “9” and “+10”) to select
the language or angle, then press
“ENT” or “:”.
1
2
Current chapter
number
Current audio
language
Repeat setting
(Only during repeat
playback)
Audio recording system
Press “DISP.” once
more to turn the
display off.
DISP.
TUNER
3
SUB T. ON/OFF. AUDIO
4
5
6
ANGLE
7
ENT
ENT
or
or
8
OP/
CL
0
9
UP
+10
SOURCE
SLOW
21
Displaying the disc status
Displaying the
disc status
Video CD
CD
Use the procedure described below to display
the status (track number, etc.) of the currently
playing video CD or music CD on the screen.
During playback, press DISP.
TUNER
“DISP.”.
The playback status is
displayed.
BAND
RTN
Playback control (PBC)
ON/OFF (For video CDs only)
UT
V.O
DISP.
TUNER
TV system (NTSC or PAL)
Playback disc
Current track
(CD: Music CD
VCD: Video CD)
Operating mode
number
Track playback
time
Repeat setting (Default setting-disc repeat)
Note: For music CDs, the playing status is
displayed even when “DISP.” is not pressed.
Press “DISP.” once
more to turn the
display off.
22
DISP.
TUNER
Video output ON/OFF
Video output ON/OFF
(Only when CVA-1005R/IVA-M700R/
IVA-C800R is connected)
Note: This output is at a fixed level and requires a
preamp with a volume control to adjust
listening levels.
When this unit is used with the CVA1005R/IVA-M700R/IVA-C800R + the
TME-M750 (Extra Monitor for Rear Seat),
the DVD video can be viewed independently of what’s being viewed on the CVA1005R/IVA-M700R/IVA-C800R.
For example, DVD video can be monitored on the Rear Monitor, while a
Navigation map is displayed on the CVA1005R/IVA-M700R/IVA-C800R. If an
audio source is selected, the main audio
system will be used to listen to the CVA1005R/IVA-M700R/IVA-C800R. Use the
RCA connectors at the rear of the DVA5205P to feed audio to your Rear monitor.
Set AUX OUT of “Selecting Rear
Monitor” on the CVA-1005R/IVAM700R/IVA-C800R side to AUX 1.
Change the source on the CVA1005R/IVA-M700R/IVA-C800R
side to MD, CD, radio, etc.
Use the “Playing 2 Sources
Simultaneously” function on the
CVA-1005R/IVA-M700R/IVAC800R side to select DVD with
the V.SEL button.
Press “V.OUT” on the
remote control unit for
this equipment at least
2 seconds.
BAND
RTN
T
U
V.O
To release, press “V.OUT” for
at least 2 seconds.
Note: Refer to the Instruction Manual of the CVA1005R/IVA-M700R/IVA-C800R for operation
on the CVA-1005R/IVA-M700R/IVA-C800R
side.
23
Changing the default settings (setup)
SET UP Changing the language settings
Changing the default
settings (setup)
The factory default settings can be
changed to suit your personal preferences and usage.
ENT
In the stop mode, press
“SET” for at least 2
seconds.
DISP
MENU
SET
BAND
RTN
DISP
MENU
SET
The default setting menu
appears.
UT
V.O
Note: This operation cannot be performed in the
PRE-STOP mode.
Use the “Joystick” to
make the selection,
then press “ENT”.
For the procedure after
ENT
selecting the setting item,
refer to the pages
indicated on the table below.
or
ENT
Item
Description
See
page
LANGUAGES Set the audio language, subtitle →P24
language and menu language.
Note: When the settings are changed, the old
settings are overwritten. Make a note of the
current settings before making changes.
The settings are not cleared even when the
vehicle’s battery is disconnected.
TV SCREEN Set the screen size according to
→P26
the type of TV monitor being used.
COUNTRY
CODE
Set the country code when
setting the rating level.
→P27
RATING
LEVEL
Set the rating level (parental
lock).
→P28
DOWN
SAMPLING
Takes DVD digital sound and →P30
converts it into 48 kHz/16 bit
sampling digital sound.
DIGITAL OUT Set the digital output.
24
→P32
LED
INDICATOR
Set whether the front panel’s →P34
LED indicators are on or off.
CUSTOM
SETUP
Set the Closed Caption and
Ai-NET setting.
→P35
Changing the
language settings
The audio language, subtitle language and
menu language can be set according to your
preferences.
Select “LANGUAGES” under
“Changing the default settings
(SET UP)” on page 24.
SET UP
Changing the language settings
ORIGINAL
The disc is played with the audio
language set as the priority language for
the disc. (AUDIO only)
Use the “Joystick” to
make the selection, then
press “ENT”.
ENT
ENT
AUDIO
Set the audio language produced from
the speakers.
SUBTITLE
Set the language of the subtitles displayed on the screen.
MENU LANGUAGE
Set the language used for the menus (title
menu, etc.).
The setup screen for the selected
language is displayed.
AUTO
The disc is played with the subtitle
language set as the priority language for
the disc. (SUBTITLE/MENU LANGUAGE
only)
OTHERS
Set this to play the disc with a language
other than one of the languages displayed. Use the keys “0” to “9” to input
the 4-digit language code, then press
“ENT”. For the language codes, refer to
“List of language codes” (page 61).
Use the “Joystick” to select the
desired language, then press
“ENT”.
ENT
ENT
Displays the setting contents.
SET UP
AUDIO
(audio languages)
SUBTITLE
(subtitle languages)
MENU
LANGUAGE
(menu languages)
Notes:
• If the disc does not include the selected
language, the disc’s default language is set.
• Languages set upon shipment from the factory:
Audio language : ORIGINAL
Subtitle language : AUTO
Menu language : AUTO
• Press “RTN” to return to the previous screen.
Press “SET” for at least
2 seconds.
The settings are stored and
the set up mode is canceled.
DISP
MENU
SET
25
SET UP Changing the TV screen settings
Changing the TV
screen settings
Use the procedure described below to set
the output screen according to the type of
TV monitor being used.
ENT
Select “TV SCREEN” under
“Changing the default settings
(SET UP)” on page 24.
DISP
MENU
SET
BAND
RTN
UT
V.O
Use the “Joystick” to
make the selection,
then press “ENT”.
ENT
ENT
4 : 3 LETTERBOX
Select this when connected to a conventional
4:3 size (normal TV aspect ratio) monitor.
There may be black stripes visible at the top
and bottom of the screen. The width of these
stripes will depend upon the original aspect
ratio of the theatrical release of the movie.
DN
CLR
0
∼
9
4 : 3 PAN-SCAN
Select this when connected to a conventional
4:3 size monitor. The picture will fill the entire
TV screen. However, due to the mismatch in
aspect ratio, parts of the movie at the extreme
left and right sides will not be visible.
26
Changing the country code setting
16 : 9 WIDE
Select this when connected to a wide screen
TV. This is selected upon shipment from the
factory.
Press “ENT” to reset the
country code.
SET UP
ENT
Use keys “0” to “9” to input the
4-digit country code, then press
“ENT”.
Displays the setting contents.
1
2
3
SUB T. ON/OFF. AUDIO
4
5
6
ANGLE
7
8
9
OP/
CL
0
Notes:
• For some discs, the picture may not be set to the
selected screen size. (For details, refer to the
explanation on the disc’s jacket.)
• Press “RTN” to return to the previous screen.
Press “SET” for at least
2 seconds.
The settings are stored
and the set up mode is
canceled.
DISP
MENU
SET
Changing the country
code setting
Set the country code when setting the
rating level (Parental lock).
Select “COUNTRY CODE” under
“Changing the default settings
(SET UP)” on page 24.
Displays the setting contents.
ENT
SET UP
Notes:
• For the country codes, refer to “List of country
codes” (Page 63).
• Can be erased one digit at a time each time
“CLR” is pressed.
• Press “RTN” to return to the previous screen.
Press “SET” for at least
2 seconds.
The settings are stored
and the set up mode is
canceled.
DISP
MENU
SET
27
SET UP Setting the rating level (parental lock)
Setting the rating
level (parental lock)
Use this function to restrict the viewing
of movies to children of appropriate
age levels only.
ENT
Select “RATING LEVEL” under
“Changing the default settings
(SET UP)” on page 24.
DISP
MENU
SET
BAND
RTN
UT
V.O
Press “ENT”.
The password input mode is set.
ENT
Use keys “0” to “9” to input the 4digit password.
The default password is 1111 upon
shipment from the factory.
1
2
3
SUB T. ON/OFF. AUDIO
4
5
6
ANGLE
7
8
OP/
CL
0
Input numbers are
displayed “ ”.
0
∼
9
Press “ENT”.
ENT
28
9
Setting the rating level (parental lock)
Use the “Joystick” to select the
rating level, then press “ENT”.
Select “OFF” to cancel the parental lock
or if you do not want to set a rating level.
The higher the number, the higher the
rating level.
SET UP
• Changing the rating level temporarily
Tips
Some discs may request that you change the
rating level set in the default settings during
playback. In this case, the following message
appears on the screen:
Still picture
ENT
Still Picture
ENT
When this appears, if you do not input the correct
password either playback does not continue or a
picture for a different rating level is played.
Displays the setting contents.
Note: Press “RTN” to return to the previous
screen.
Press “SET” for at least
2 seconds.
The settings are stored
and the set up mode is
canceled.
DISP
MENU
SET
SET UP
Notes:
• If you want to change the password, select
“CHANGE PASSWORD”, then input the new
password (4 digits).
• Write down the password on a piece of paper and
store the piece of paper somewhere in case you
forget it.
• On unrated DVDs, playback will not be restricted
even if the rating level is set.
• Once set, this rating level remains in memory
until changed. To enable the play of discs of
higher rating levels or to cancel the parental lock,
the setting must be changed.
• Not all DVDs provide a Parental Lock feature. If
you are unsure about a DVD, play it first to
confirm. Do not leave DVDs accessible to young
children for whom you deem them inappropriate.
.
29
SET UP Changing the down sampling setting
Changing the down
sampling setting
Converts linear PCM (LPCM) voice
signals recorded on the DVD disc to
downsampling 48 kHz/16 bit digital
signals and outputs them from the optical
cable.
ENT
DISP
MENU
SET
BAND
RTN
Select “DOWN SAMPLING” under
“Changing the default settings
(SET UP)” on page 24.
UT
V.O
Move the “Joystick” up and
down to choose “ON” or “OFF”
and, then press “ENT”.
ENT
ENT
ON
The digital signals recorded on the DVD
disc with 96 kHz/24bit, 48 kHz/24bit, 48
kHz/20bit sampling are converted into
digital signals with 48 kHz/16bits
sampling for output from the optical cable.
Set to ON at time of shipment from
factory.
OFF
The digital signals recorded on the DVD
disc with 96 kHz/24bit, 48 kHz/24bit, 48
kHz/20bit sampling are not converted into
digital signals with 48 kHz/16bits
sampling. They are not output from the
optical cable.
30
Changing the down sampling setting
SET UP
Displays the setting contents.
Note: Press “RTN” to return to the previous
screen.
Press “SET” for at least
2 seconds.
The settings are stored
and the set up mode is
canceled.
DISP
MENU
SET
SET UP
31
SET UP Changing the digital output setting
Changing the digital
output setting
Use the following procedure to set the
audio signal output from the DVA-5205P.
Select “DIGITAL OUT” under
“Changing the default settings
(SET UP)” on page 24.
ENT
DISP
MENU
SET
BAND
RTN
UT
V.O
Use the “Joystick” to make the
selection, then press “ENT”.
ENT
ENT
AUTO
The digital output is switched automatically
according to the type of audio signals being
played.
Be sure to select “AUTO” when you want to
connect a digital audio processor and play
Dolby Digital audio. “AUTO” is selected upon
shipment from the factory.
LPCM
The audio signals recorded on the disc are
converted into 48 kHz/16 bit (for DVDs) or 44.1
kHz (for video CDs and CDs) linear PCM audio
signals for output.
32
Changing the digital output setting
Displays the setting contents.
Press “SET” for at least
2 seconds.
The set up are stored and
the set up mode is canceled.
SET UP
DISP
MENU
SET
Note: Press “RTN” to return to the previous
screen.
• Audio output/Optical digital audio output
Disc
Audio recording
format
Digital output
setting
DVD
DTS
AUTO
LPCM
Dolby Digital
AUTO
LPCM
Linear PCM
AUTO
(48 kHz)
LPCM
Linear PCM
AUTO
(96 kHz)
LPCM
Down sampling
setting
Optical digital audio Analog audio
output (when a
output (Ai-NET,
digital audio
RCA output)
processor is
connected)
ON
DTS
X
OFF
DTS
X
ON
X
X
OFF
X
X
ON
Dolby Digital
O
OFF
Dolby Digital
O
ON
LPCM (48kHz/16 bit)
O
OFF
X
O
ON
LPCM (48kHz/16 bit)
O
OFF
X
O
ON
LPCM (48kHz/16 bit)
O
OFF
X
O
ON
LPCM (48kHz/16 bit)
O
OFF
X
O
ON
LPCM (48kHz/16 bit)
O
OFF
X
O
Video CD
MPEG
AUTO or LPCM
ON or OFF
LPCM (44.1kHz)
O
CD
Linear PCM
AUTO or LPCM
ON or OFF
LPCM (44.1kHz)
O
SET UP
33
SET UP Changing the LED indicator setting
Changing the LED
indicator setting
Use the following procedure to set whether or
not the product’s LED indicators are on or off.
ENT
Select “LED INDICATOR” under
“Changing the default settings
(SET UP)” on page 24.
DISP
MENU
SET
BAND
RTN
Use the “Joystick” to select the
“ON” or “OFF”, then press
“ENT”.
UT
V.O
ENT
ENT
ON
The LED indicators are lit, indicating the
product’s operating status. “ON” is selected
upon shipment from the factory.
OFF
The LED indicators are turned off.
When “OFF” is set, the indicators do not light
even when the power is on.
34
Custom setting – Changing the Closed Caption setting
Displays the setting contents.
SET UP
Move the “Joystick” up and
down to select “ON” or “OFF”,
then press “ENT”.
ENT
ENT
Note: Press “RTN” to return to the previous
screen.
Press “SET” for at
least 2 seconds.
DISP
MENU
SET
The settings are stored
and the set up mode is
canceled.
Custom setting –
Changing the Closed
Caption setting
DVD includes so-called “closed captions”
which describe the scene to persons with
impaired hearing. It is possible to turn the
closed captions ON and OFF.
ON
Displays the closed captions.
OFF
Does not display the closed captions.
Set to OFF at time of shipment from
factory.
Displays the setting contents.
SET UP
Select “CUSTOM SETUP” under
“Changing the default settings
(SET UP)” on page 24.
Move the “Joystick” up and
down to select “CLOSED CAPTION”, then press “ENT”.
ENT
Notes:
• Please be aware that closed captions are
different from titles.
• Press “RTN” to return to the previous screen.
ENT
Press “SET” for at
least 2 seconds.
The settings are stored
and the set up mode is
canceled.
DISP
MENU
SET
35
SET UP Custom setting – Changing the Ai-NET settings
Custom setting –
Changing the Ai-NET
settings
The Ai-NET settings are used to output the
sound of connected Ai-NET products.
ENT
Select “CUSTOM SETUP” under
“Changing the default settings
(SET UP)” on page 24.
DISP
MENU
SET
BAND
RTN
UT
V.O
Use the “Joystick” to select “AiNET SETUP”, then press “ENT”.
ENT
ENT
Use the “Joystick” to select
“DVD” or “CD”, then press
“ENT”.
ENT
ENT
36
Custom setting – Changing the Ai-NET settings
DVD
Set to “DVD” when connected to the CVA1005R/IVA-M700R/IVA-C800R.
Operations can be performed using the CVA1005R/IVA-M700R/IVA-C800R’s main menu
screen.
For details, refer to the operating instructions of
the CVA-1005R/IVA-M700R/IVA-C800R.
“DVD” is selected upon shipment from the
factory.
CD
Set to “CD” when connected to an Ai-NET
product (head unit) other than the CVA-1005R/
IVA-M700R/IVA-C800R (for ex.: CVA-1000R).
Operations can be performed from the head
unit.
For details, refer to “Operating from the head
unit” (page 56).
Displays the setting contents.
Notes:
• Press “RTN” to return to the previous screen.
• If the Ai-NET setting is “CD” when used with the
CVA-1005R/IVA-M700R/IVA-C800R, operation
from the main menu screen is not possible.
• If the Ai-NET setting is “DVD” when used with any
Ai-NET compatible head unit other than the CVA1005R/IVA-M700R/IVA-C800R, volume is the
only operation possible from the head unit.
• To call the DVD video by using the CVA-1000R,
switch the mode to “AUX” with the V. SEL button
on the CVA-1000R.
• When the Ai-NET setting is “CD”, the operable
functions and displays may differ depending on
the Ai-NET compatible head unit connected.
Press “SET” for at least
2 seconds.
The settings are stored
and the set up mode is
canceled.
SET UP
DISP
MENU
SET
Turn off the vehicle’s ignition, then turn
it on again.
Notes:
Cases in which DVDs cannot be played on the
CVA-1005R/IVA-M700R/IVA-C800R side
– When “DVD” is not displayed on the CVA-1005R/
IVA-M700R/IVA-C800R side menu screen
– When DVDs cannot be played even when AUX1
is selected
This is because the DVA-5205P’s Ai-NET setting is
set to “CD”.
Use the procedure described below to change the
setting.
1. Remove the disc from the DVA-5205P.
2. Turn on the power of the DVA-5205P and CVA1005R/IVA-M700R/IVA-C800R.
Also start up the CVA-1005R/IVA-M700R/IVAC800R monitor.
3. Press the CVA-1005R/IVA-M700R/IVA-C800R
SOURCE switch and select “CD” from the menu.
4. Press the SOURCE switch, then select “V.SEL”
from the menu.
5. In the V.SEL mode, select “AUX1”. This displays
the DVA-5205P screen.
6. On the DVA-5205P, set the Ai-NET setting to
“DVD”. Refer to “Changing the Ai-NET settings”
(pages 36 and 37).
7. Turn the car’s ignition switch off, then turn it back
on.
SET UP
37
SET UP Custom setting – Changing the H.U. CONTROL settings
Custom setting –
Changing the H.U.
CONTROL settings
When connecting this equipment with an
Ai-NET compatible head unit or an AiNET compatible AV head unit (CVA1005R/IVA-M700R/IVA-C800R), set the
equipment so that it is possible to control
from the head unit.
ENT
DISP
MENU
SET
BAND
RTN
UT
V.O
Select “CUSTOM SETUP” under
“Changing the default settings
(SET UP)” on page 24.
Move the “Joystick” up and
down to select “H.U. CONTROL”,
then press “ENT”.
ENT
ENT
Move the “Joystick” up and
down to select “ON” or “OFF”,
then press “ENT”.
ENT
ENT
38
Custom setting – Changing the H.U. CONTROL settings
SET UP
ON
Possible to operate from an Ai-NET
compatible head unit or an Ai-NET
compatible AV head unit (CVA-1005R/
IVA-M700R/IVA-C800R).
OFF
Not possible to operate from an Ai-NET
compatible head unit or an Ai-NET
compatible AV head unit (CVA-1005R/
IVA-M700R/IVA-C800R). Set to OFF at
time of shipment from factory.
Displays the setting contents.
Note: Press “RTN” to return to the previous
screen.
Press “SET” for at
least 2 seconds.
The settings are stored
and the set up mode is
canceled.
DISP
MENU
SET
SET UP
39
Operating the digital audio processor (optional)
Operating the DVD VideoCDCD
digital audio
processor (optional)
When used with a digital audio processor (PXAH510), operation is possible from the remote
control unit included with the DVA-5205P. Also
refer to the PXA-H510’s operating instructions.
ENT
BAND
RTN
UT
V.O
During playback,
press “A.PROC”.
V. SEL
The setting menu appears.
A. PROC
BAND
Use the “Joystick” to
make the selection, then
press “ENT”.
A. PROC
BAND
For the procedure after
making a selection, refer
to the pages indicated on
the table below.
ENT
ENT
Item
Description
PARAMETRIC- Adjust the parametric equalizer’s band frequency,
EQ
band width and level.
→P41
SURROUND
Select one of six surround modes according to the →P42
music source using DSP (digital signal processing).
PRIVATEMEMORY
Store and recall up to six parametric equalizer
adjustments and settings.
TIMEEliminate time delays resulting from the distance
CORRECTION between the listening position and the speakers.
40
See
page
→P43
→P45
DOLBY
SURROUND
MODE
Switch between the Dolby Digital input and the Pro →P45
Logic input.
ADJUST
Adjust the speaker mode, speaker level, etc.
→P46
MODE
Adjust the volume, fader, balance, etc.
→P53
Adjusting the parametric equalizer
Adjusting the
parametric equalizer
Select “PARAMETRIC-EQ” under
“Operating the digital audio
processor (optional)” on page 40.
Use the “Joystick” to select the
band to be set, then press “ENT”.
The band whose frequency is indicated in
yellow can be adjusted. The parametric
equalizer’s setting screen consists of two
pages. Press “BAND” for at least 2
seconds to switch between pages 1 and
2.
ENT
ENT
Use the “Joystick” to select the
band width (Q-FACT), then press
“ENT”.
ENT
ENT
Use the “Joystick” to adjust the
band width, then press “ENT”.
ENT
ENT
Use the “Joystick” to select the
level (LV), then press “ENT”.
ENT
ENT
Use the “Joystick” to adjust the
level, then press “ENT”.
V. SEL
A. PROC
BAND
ENT
ENT
Note: Press “RTN” to return to the previous
screen.
Use the “Joystick” to adjust the
frequency, then press “ENT”.
ENT
ENT
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
A. PROC
BAND
41
Adjusting the surround settings
Adjusting the
surround settings
This adjustment is not possible when Dolby
Digital or Pro Logic is turned on for the DVA5205P’s audio output.
ENT
Select “SURROUND” under
“Operating the digital audio
processor (optional)” on page 40.
BAND
RTN
UT
V.O
Use the “Joystick” to select the
surround mode, then press “ENT”.
There are six surround modes.
ENT
ENT
A. PROC
BAND
Press “ENT”.
The level (LV) value turns
yellow.
ENT
Use the “Joystick” to adjust the
level (LV), then press “ENT”.
ENT
42
ENT
Storing the surround settings
Use the “Joystick” to select the
time (echo time), then press
“ENT”.
ENT
Use the “Joystick” to select
“WRITE”, then press “ENT”.
ENT
ENT
ENT
Use the “Joystick” to adjust the
time, then press “ENT”.
ENT
ENT
Use the “Joystick” to select the
memory location at which you
want to store the settings (“PRIVATE-MEMORY 1” to “PRIVATEMEMORY 6”), then press “ENT”.
Note: Press “RTN” to return to the previous
screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
A. PROC
ENT
BAND
DVD
Storing the
surround settings
Video CD
ENT
Note: Press “RTN” to return to the previous
screen.
CD
Select “PRIVATE-MEMORY” under
“Operating the digital audio
processor (optional)” on page 40.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
A. PROC
BAND
43
Recalling the surround settings
DVD
Recalling the
surround settings
Video CD
Select “PRIVATE-MEMORY” under
“Operating the digital audio
processor (optional)” on page 40.
ENT
BAND
RTN
UT
V.O
Use the “Joystick” to select the
memory location you want to
recall (“PRIVATE-MEMORY 1” to
“PRIVATE-MEMORY 6”), then
press “ENT”.
ENT
ENT
A. PROC
BAND
Note: Press “RTN” to return to the previous
screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
44
CD
A. PROC
BAND
Adjusting the time compensation
Using the Pro Logic mode
DVD
Adjusting the
time compensation
Video CD
CD
Using the Pro
Logic mode
DVD Video CD
CD
Select “TIME-CORRECTION”
under “Operating the digital audio
processor (optional)” on page 40.
Select “DOLBY SURROUND
MODE” under “Operating the
digital audio processor (optional)”
on page 40.
Use the “Joystick” to select the
speaker to be adjusted, then
press “ENT”.
Use the “Joystick” to make the
selection, then press “ENT”.
ENT
ENT
Use the “Joystick” to adjust the
time, then press “ENT”.
ENT
ENT
ENT
DOLBY DIGITAL
“DOLBY DIGITAL” is set automatically
when the disc is Dolby Digital compatible
and the DVD video player’s audio output
setting is set to “AUTO”.
DOLBY PRO LOGIC
Note: Press “RTN” to return to the previous
screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
ENT
“DOLBY PRO LOGIC” or “OFF” can be
selected when the disc is Dolby Pro Logic
compatible and the DVD video player’s
audio output setting is set to “LPCM”.
When “OFF” is selected, the surround
settings cannot be adjusted.
Note: Press “RTN” to return to the previous
screen.
A. PROC
BAND
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
A. PROC
BAND
45
ADJUST – Setting the speaker mode
ADJUST –
Setting the
speaker mode
DVD Video CD
CD
This adjustment cannot be made when
Dolby Pro Logic is set to “OFF”.
ENT
Select “ADJUST” under “Operating the digital audio processor
(optional)” on page 40.
BAND
RTN
UT
V.O
Use the “Joystick” to select the
speaker to be set (“FRONT”,
“CENTER” or “REAR”), then press
“ENT”.
ENT
ENT
A. PROC
BAND
Use the “Joystick” to switch the
mode.
ENT
FRONT
LARGE/SMALL
CENTER
OFF/LARGE/SMALL
REAR
OFF/LARGE/SMALL
Note: Press “RTN” to return to the previous
screen.
46
ADJUST – Adjusting the acoustic image
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
ADJUST –
Adjusting the
acoustic image
Use the “Joystick” to select the
level item, then press “ENT”.
A. PROC
BAND
ENT
ENT
DVD Video CD
CD
Use the “Joystick” to
adjust the level, then press “ENT”.
This adjustment cannot be made when
Dolby Pro Logic is set to “OFF”.
Select “ADJUST” under “Operating the digital audio processor
(optional)” on page 40.
Use the “Joystick” to select “BIPHANTOM”, then press “ENT”.
ENT
ENT
ENT
ENT
Note: Press “RTN” to return to the previous
screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
A. PROC
BAND
Use the “Joystick” to select the
mode (“ON” or “OFF”), then press
“ENT”.
ENT
ENT
Note: The “BI-PHANTOM” setting is automatically
set to “OFF” when the center speaker is set
to “OFF”.
47
ADJUST – Mixing the rear audio channels
ADJUST –
Mixing the rear
audio channels
DVD Video CD
CD
Use this function to mix the audio signals
for the front to those output from the rear
speakers.
ENT
BAND
RTN
Select “ADJUST” under “Operating the digital audio processor
(optional)” on page 40.
UT
V.O
Use the “Joystick” to
select “REAR MIX”, then press
“ENT”.
ENT
ENT
A. PROC
BAND
Use the “Joystick” to select the
mode (“ON” or “OFF”), then press
“ENT”.
ENT
ENT
Note: The “REAR MIX” setting is automatically set
to “OFF” when the rear speaker is set to
“OFF”.
Use the “Joystick” to select the
level item, then press “ENT”.
ENT
48
ENT
ADJUST – Center speaker time compensation
Use the “Joystick” to adjust the
level, then press “ENT”.
ENT
ENT
Note: Press “RTN” to return to the previous
screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
ADJUST –
DVD Video CD
CD
Center speaker
time compensation
Compensation is not possible when the
center speaker is set to “OFF”.
Select “ADJUST” under “Operating the digital audio processor
(optional)” on page 40.
Use the “Joystick” to select
“CENTER DELAY”, then press
“ENT”.
ENT
A. PROC
BAND
ENT
Use the “Joystick” to adjust the
level, then press “ENT”.
ENT
ENT
Note: Press “RTN” to return to the previous
screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
A. PROC
BAND
49
ADJUST – Rear speaker time compensation
ADJUST –
DVD Video CD
CD
Rear speaker time
compensation
Compensation is not possible when the
rear speakers are set to “OFF”.
ENT
Select “ADJUST” under “Operating the digital audio processor
(optional)” on page 40.
BAND
RTN
UT
V.O
Use the “Joystick” to select
“REAR DELAY”, then press
“ENT”.
ENT
ENT
A. PROC
BAND
Use the “Joystick” to adjust the
level, then press “ENT”.
ENT
ENT
Note: Press “RTN” to return to the previous
screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
50
A. PROC
BAND
ADJUST – Achieving powerful sound at low volumes
ADJUST –
DVD Video CD
Achieving powerful
sound at low volumes
CD
This setting is only possible with Dolby
Digital outputs.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
A. PROC
BAND
Select “ADJUST” under “Operating the digital audio processor
(optional)” on page 40.
Use the “Joystick” to select
“LISTENING”, then press “ENT”.
ENT
ENT
Use the “Joystick” to select the
mode.
ENT
L-NIGHT
For powerful sound at low volumes (to
compensate for high levels of background
noise such as road noise)
STANDARD
For more powerful sound at regular
volumes
MAXIMUM
For the regular sound
Note: Press “RTN” to return to the previous
screen.
51
ADJUST – Adjusting the speaker level
ADJUST –
Adjusting the
speaker level
DVD Video CD
CD
Select “ADJUST” under “Operating the digital audio processor
(optional)” on page 40.
ENT
BAND
RTN
UT
V.O
Press “BAND” for at least 2
seconds to switch the “ADJUST”
screen.
V. SEL
A. PROC
BAND
A. PROC
BAND
Use the “Joystick” to select
“TEST TONE”, then press “ENT”.
ENT
ENT
Use the “Joystick” to select “ON”,
then press “ENT”.
Test tones are produced for two seconds
from each speaker.
ENT
ENT
Note: Test tones are not produced from the center
and rear speakers when these speakers are
set to “OFF”.
52
MODE – Adjusting the volume, fader and balance
Use the “Joystick” to select the
speaker, then press “ENT”.
Adjust so that the volume level from the
different speakers is the same.
MODE –
DVD Video CD
Adjusting the volume,
fader and balance
CD
When a head unit is connected using Ai-NET
connections, adjust the volume, fader and
balance from the head unit.
ENT
ENT
Use the “Joystick” to adjust the
level, then press “ENT”.
ENT
ENT
Select “MODE” under “Operating
the digital audio processor
(optional)” on page 40.
Use the “Joystick” to select the
item to be adjusted, then press
“ENT”.
ENT
ENT
Note: Press “RTN” to return to the previous
screen.
Once the levels of
V. SEL
all the speakers
have been
adjusted, either
set “TEST TONE” to
“OFF” or press “A.PROC” to close
the digital audio processor screen
and return to the playback screen.
A. PROC
BAND
Use the “Joystick” to adjust.
ENT
Note: Press “RTN” to return to the previous
screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
A. PROC
BAND
53
MODE – Adjusting the subwoofer
MODE –
Adjusting the
subwoofer
DVD Video CD
CD
Select “MODE” under “Operating
the digital audio processor
(optional)” on page 40.
ENT
BAND
RTN
UT
V.O
Use the “Joystick” to select “SUBW”, then press “ENT”.
ENT
ENT
A. PROC
BAND
Use the “Joystick” to select the
mode (“ON” or “OFF”), then press
“ENT”.
ENT
ENT
Note: The subwoofer cannot be adjusted when set
to “OFF”.
Use the “Joystick” to select the
level item, then press “ENT”.
ENT
54
ENT
MODE – Turning the defeat function on and off
Use the “Joystick” to adjust the
level, then press “ENT”.
ENT
ENT
Note: Press “RTN” to return to the previous
screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
MODE –
DVD Video CD
CD
Turning the defeat
function on and off
Select “MODE” under “Operating
the digital audio processor
(optional)” on page 40.
Use the “Joystick” to select
“DEFEAT”, then press “ENT”.
ENT
ENT
A. PROC
BAND
Use the “Joystick” to select the
mode (“ON” or “OFF”), then press
“ENT”.
ON :
OFF :
The response is flat.
Off
ENT
ENT
Notes:
• When “DEFEAT” is set to “ON”, the “PARAMETRIC-EQ”, “SURROUND”, “PRIVATE-MEMORY”
and “TIME-CORRECTION” settings cannot be
adjusted.
• Press “RTN” to return to the previous screen.
Press “A.PROC”
V. SEL
to close the
digital audio
processor screen
and return to the playback screen.
A. PROC
BAND
55
Operating from the head unit
CDA-7865R
(head unit)
DVA-5205P
(player)
Operating from the head unit
The DVA-5205P can also be operated from the head unit.
This section describes operations from the CDA-7865R (the recommended head unit).
Note that some of the functions cannot be operated from the DVA-5205P.
Playing DVDs, video CDs and CDs
Press “SOURCE” and select the
CD (DVA-5205P) mode.
The mode switches each time the button
is pressed.
TUNER
CD (Built-in)
CD(DVA-5205P)
CHANGER *
( * only when a changer is connected.)
The DVA-5205P’s power is on when the
CD mode is selected, off when other
modes are selected.
To set the pause mode, press
”.
“
Press “
” again to resume playback.
Note: Playback starts at the beginning of the disc whenever ignition is turned off or another Ai-NET source
is selected.
56
Operating from the head unit
Displaying the CD title
Press “TITLE” to display the CD title, etc., on the head unit’s display.
Press “TITLE” on the head unit.
The display pattern changes each time
the button is pressed.
Operation display
(CDA-7865R) TRACK NO./TIME*1
Clock display mode
Clock display
Text display mode
Disc Name display*2
Text display mode
Track Name display*2
Title display mode
Title display*3
Notes:
*1In the TRACK NO./TIME display mode the time display shows 0:00 and does not move.
*2Displayed during playback of a text compatible CD (when using an optional text compatible). “NO TEXT” will
be displayed when the CD is not text compatible.
*3“--------” will be displayed when the title has not been inputted.
<Functions operable from the CDA-7865R>
Switch
Operation
SOURCE
Turns the power on and off.
When pressed again, the source switches.
The DVD player’s power is on when the CD mode is selected, off when other modes
are selected.
TITLE
Switches the display pattern. / Sets the title input mode.
RPT
DVD: Chapter repeat
f
c
:/j
Video CD/CD: Switches between track repeat and disc repeat
Rotary Encoder
Starts playback from the beginning of the following chapter/track.
When pressed and held in, fast-forwards the disc.
Starts playback from the beginning of the current chapter/track.
When pressed and held in, fast-reverses the disc.
Switches between play and pause.
Adjust the volume.
Notes:
• The functions and operations may differ when using with a head unit other than the CDA-7865R.
• For video CDs with playback control (PBC), turn PBC off.
• Titles can be input for video CDs and CDs. For details, refer to the operating instructions of the connected
head unit.
57
Operating from the head unit’s remote control unit
Operating from the head unit’s remote control
unit
The DVA-5205P can be operated from the remote control unit included with the head unit.
Remote control operations
Operation
•
58
Remote Control
unit
RUE-4185
RUE-4160
RUE-4167
P10
Power on/off
O
O
O
P14
Fast-forward/fast-reverse
O
O
O
P15
Still picture (pause)
O
O
O
P14
Chapter/track search
O
O
O
There may be restrictions to some of the functions and displays depending on the
Ai-NET compatible product (head unit/remote control unit) being used.
Operating from the head unit’s remote control unit
ENT
ENT
ENT
A.SEL
SOURCE
AUDIO
SEL
RUE-4185
RUE-4160
MENU
RUE-4165
RUE-4167
Operating DVDs, video CDs and CDs
First see “Remote control operations” (page 58).
1
Press “SOURCE” , “AUDIO SEL” or “A. SEL”to set the CD (DVA-5205P)
mode.
The DVA-5205P’s power is on when the CD mode is selected, off when other modes are
selected.
2
To set the pause mode, press “
3
Press and hold “ ” or “ ” continuously to make FF or RW operation.
(RUE-4185, RUE-4160)
Tilt and hold the joystick in left or right direction to make FF or RW operation. (RUE-4167)
4
Press “ ” or “ ” to make a track or chapter skip. (RUE-4185, RUE-4160)
Tilt the joystick in left or right direction to make a track or chapter skip.
(RUE-4167)
Press “
” or “ENT”.
” or “ENT” again to resume playback.
c
c
f
f
Notes:
• For adjusting the volume and other basic operations, refer to the head unit’s operating instructions.
• For video CDs with playback control (PBC), turn PBC off.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY
Warning FROM SAFELY DRIVING YOUR VEHICLE. Any function that requires your
prolonged attention should only be performed after coming to a complete stop.
Always stop the vehicle in a safe location before performing these functions.
Failure to do so may result in an accident.
59
Terminology
Terminology
Dolby Digital
DTS
Dolby Digital is a digital audio compression technology developed by Dolby
Laboratories. It is compatible with not
only stereo (2-channel) sound, but also
5.1-channel surround sound. The signals
for the different channels are completely
independent, so large quantities of audio
data can be recorded efficiently on discs,
and since the sound is digital there is little
loss of sound quality.
This is a home-use digital sound format of
the DTS Sound System. This is a high
quality sound system, developed by
Digital Theater Systems Corp for use in
movie theaters.
DTS has six independent sound tracks.
The theater presentation is fully realized
in the home and other settings. DTS is
the abbreviation for Digital Theater
System.
* To enjoy DTS surround sound you need
the separately sold DTS digital audio
processor. The DVD video software
must also have a DTS sound track.
* The separately sold digital audio
processor (PXA-H510) is required to
enjoy Dolby Digital sound.
Dolby Pro Logic
Center
speaker
Front
speakers
Rear
speakers
Subwoofer
Speaker layout for enjoying
Dolby Digital sound/dts sound
60
Dolby Pro Logic is a Dolby Surround
format encoded onto two channels.
Proper decoding reproduces four channels (front left/right, center and rear
surround (monaural)) upon playback.
* The separately sold digital audio
processor (PXA-H510) is required to
enjoy Dolby Pro Logic sound.
Linear PCM audio (LPCM)
LPCM is a signal recording format used
for music CDs. Whereas music CDs are
recorded at 44.1 kHz/16 bits, DVDs are
recorded at 48 kHz/16 bits to 95 kHz/24
bits, thereby achieving higher sound
quality than music CDs.
Rating levels (parental lock)
This is a function of the DVD for restricting
the viewing age as stipulated by laws in
different countries. The way in which
viewing is restricted differs from DVD to
DVD. Sometimes the DVD cannot be
played at all, other times certain scenes
are skipped, and other times certain
scenes are replaced with other scenes.
List of language codes
List of language codes
(For details, see page 25.)
Abbreviation
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DE
DZ
EL
EN
EO
ES
ET
EU
FA
FI
FJ
FO
FR
FY
GA
GD
GL
GN
GU
HA
HI
HR
HU
Code
6565
6566
6570
6577
6582
6583
6589
6590
6665
6669
6671
6672
6673
6678
6679
6682
6765
6779
6783
6789
6865
6869
6890
6976
6978
6979
6983
6984
6985
7065
7073
7074
7079
7082
7089
7165
7168
7176
7178
7185
7265
7273
7282
7285
Language
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Abbreviation
HY
IA
IE
IK
IN
IS
IT
IW
JA
JI
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NL
NO
OC
OM
OR
PA
PL
Code
7289
7365
7369
7375
7378
7383
7384
7387
7465
7473
7487
7565
7575
7576
7577
7578
7579
7583
7585
7589
7665
7678
7679
7684
7686
7771
7773
7775
7776
7778
7779
7782
7783
7784
7789
7865
7869
7876
7879
7967
7977
7982
8065
8076
Language
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Punjabi
Polish
61
List of language codes
List of language codes (Continued)
(For details, see page 25.)
Abbreviation
PS
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
62
Code
8083
8084
8185
8277
8278
8279
8285
8287
8365
8368
8371
8372
8373
8375
8376
8377
8378
8379
8381
8382
8383
8384
8385
8386
Language
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Abbreviation
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZH
ZU
Code
8387
8465
8469
8471
8472
8473
8475
8476
8478
8479
8482
8483
8484
8487
8575
8582
8590
8673
8679
8779
8872
8979
9072
9085
Language
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Chinese
Zulu
List of country codes
List of country codes
(For details, see page 27.)
Abbreviation
AD
AE
AF
AG
AI
AL
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
BJ
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CD
Code
6568
6569
6570
6571
6573
6576
6577
6578
6579
6581
6582
6583
6584
6585
6587
6590
6665
6666
6668
6669
6670
6671
6672
6673
6674
6677
6678
6679
6682
6683
6684
6686
6687
6689
6690
6765
6767
6768
CF
CG
CH
CI
CK
6770
6771
6772
6773
6775
Country
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaijan
Bosnia and Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Congo, the Democratic
Republic of the
Central African Republic
Congo
Switzerland
Cote d’lvoire
Cook Islands
Abbreviation
CL
CM
CN
CO
CR
CU
CV
CX
CY
CZ
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
ER
ES
ET
FI
FJ
FK
FM
Code
6776
6777
6778
6779
6782
6785
6786
6788
6789
6790
6869
6874
6875
6877
6879
6890
6967
6969
6971
6972
6982
6983
6984
7073
7074
7075
7077
FO
FR
GA
GB
GD
GE
GF
GH
GI
GL
GM
GN
GP
GQ
GR
7079
7082
7165
7166
7168
7169
7170
7172
7173
7176
7177
7178
7180
7181
7182
Country
Chile
Cameroon
China
Colombia
Costa Rica
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Rempublic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
Eritrea
Spain
Ethiopia
Finland
Fiji
Falkland Islands
Micronesia, Federated
States of
Faroe Islands
France
Gabon
United Kingdom
Grenada
Georgia
French Guiana
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe
Equatorial Guinea
Greece
63
List of country codes
List of country codes (Continued)
(For details, see page 27.)
64
Abbreviation
GS
Code
7183
GT
GU
GW
GY
HK
HM
7184
7185
7187
7189
7275
7277
HN
HR
HT
HU
ID
IE
IL
IN
IO
7278
7282
7284
7285
7368
7369
7376
7378
7379
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
KM
KN
KP
7381
7382
7383
7384
7477
7479
7480
7569
7571
7572
7573
7577
7578
7580
KR
KW
KY
KZ
LA
7582
7587
7589
7590
7665
LB
LC
LI
LK
LR
7666
7667
7673
7675
7682
Country
South Georgia and the
South Sandwich Islands
Guatemala
Guam
Guinea-Bissau
Guyana
Hong Kong
Heard Island and
McDonald Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean
Territory
Iraq
Iran, Islamic Republic of
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia
Kiribati
Comoros
Saint Kitts and Nevis
Korea, Democratic
People’s Republic of
Korea, Republic of
Kuwait
Cayman Islands
Kazakstan
Lao People’s Democratic
Republic
Lebanon
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Abbreviation
LS
LT
LU
LV
LY
MA
MC
MD
MG
MH
MK
Code
7683
7684
7685
7686
7689
7765
7767
7768
7771
7772
7775
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
7776
7777
7778
7779
7780
7781
7782
7783
7784
7785
7786
7787
7788
7789
7790
7865
7867
7869
7870
7871
7873
7876
7879
7880
7882
7885
7890
7977
8065
8069
8070
8071
Country
Lesotho
Lithuania
Luxembourg
Latvia
Libyan Arab Jamahiriya
Morocco
Monaco
Moldova, Republic of
Madagascar
Marshall Islands
Macedonia, The former
Yugoslav Republic of
Mali
Myanmar
Mongolia
Macau
Northern Mariana Islands
Martinique
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
French Polynesia
Papua New Guinea
List of country codes
List of country codes (Continued)
(For details, see page 27.)
Abbreviation
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
SA
SB
SC
SD
SE
SG
SH
SI
SJ
SK
SL
SM
SN
SO
SR
ST
SV
SY
SZ
TC
TD
TF
TG
TH
Code
8072
8075
8076
8077
8078
8082
8084
8087
8089
8165
8269
8279
8285
8287
8365
8366
8367
8368
8369
8371
8372
8373
8374
8375
8376
8377
8378
8379
8382
8384
8386
8389
8390
8467
8468
8470
8471
8472
Country
Abbreviation
Philippines
TJ
Pakistan
TK
Poland
TM
Saint Pierre and Miquelon
TN
Pitcairn
TO
Puerto Rico
TP
Portugal
TR
Palau
TT
Paraguay
TV
Qatar
TW
Reunion
TZ
Romania
UA
Russian Federation
UG
Rwanda
UM
Saudi Arabia
Solomon Islands
US
Seychelles
UY
Sudan
UZ
Sweden
VA
Singapore
Saint Helena
VC
Slovenia
VE
Svalbard and Jan Mayen
VG
Slovakia
VI
Sierra Leone
VN
San Marino
VU
Senegal
WF
Somalia
WS
Suriname
YE
Sao Tome and Principe
YT
El Salvador
YU
Syrian Arab Republic
ZA
Swaziland
ZM
Turks and Caicos Islands
ZW
Chad
French Southern Territories
Togo
Thailand
Code
8474
8475
8477
8478
8479
8480
8482
8484
8486
8487
8490
8565
8571
8577
8583
8589
8590
8665
8667
8669
8671
8673
8678
8685
8770
8783
8969
8984
8985
9065
9077
9087
Country
Tajikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan, Province of China
Tanzania, United Republic
of
Ukraine
Uganda
United States Minor
Outlying Islands
United States
Uruguay
Uzbekistan
Holy See (Vatican City
State)
Saint Vincent and the
Grenadines
Venezuela
Virgin Island, British
Virgin Islands, U.S
Viet Nam
Vanuatu
Wallis and Futuna
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zimbabwe
65
In case of difficulty
• If operation freezes, the screen goes black or the unit should otherwise not function properly, try turning
the power off then back on. Alternatively, try the following methods in the order listed until the DVA-5205P
returns to normal playbak mode:
1) Change the source from DVD to another source then return to DVD mode.
2) Turn the car’s ignition OFF and back ON again.
3) Press the RESET button on the face of the DVA-5205P.
• This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your
system is properly connected or consult your authorized Alpine dealer.
Symptom
Unit does not
operate.
Cause
Fuse is blown.
Remedy
Replace with a fuse of the specified capacity. (See
installation instructions.)
Monitor’s power is not turned on. Turn on the monitor’s power.
Operation is
unstable.
No picture is
produced.
Condensation.
Wait a while (about 1 hour) for the condensation to
dry.
Remote control unit’s batteries
are worn.
Replace the remote control unit’s batteries with new
ones.
Remote control sensor or
transmitter is dirty.
Clean the sensor or transmitter.
Monitor’s mode is not switched
to the mode you want to see.
Switch to the mode you want to see.
Monitor’s parking brake cord is
not connected.
Connect the monitor’s parking brake cord and set the
parking brake.
(For details, refer to the monitor’s instructions.)
Monitor’s parking brake is not
set.
Playback does not
start.
Disc is loaded upside-down.
Check the disc and load it with the labeled side facing
upward.
Disc is dirty.
Clean the disc.
A disc not able to playback with
this unit is loaded.
Check if the disc is able to be played back.
Parental lock is set.
Cancel the parental lock or change the rating level.
Setup menu is displayed.
Press “SET” to turn the menu off.
Disc is being fast-forwarded or
fast-reversed.
The picture may be slightly disturbed, but this is
normal.
Vehicle’s battery power is weak.
Check the battery power and wiring.
(The unit may malfunction if the battery power is
under 11 volts with a load applied.)
Monitor’s fluorescent tube is
worn.
Replace the monitor’s fluorescent tube.
Image stops
sometimes.
Disc is scratched.
Replaced with a non-scratched disc.
NO DISC
No disc is loaded.
Load a disc.
Disc is dirty.
Clean the disc.
NOT VALID
Remote control operation is not
possible.
For some discs or playing modes, certain operations
are not possible. This is not a malfunction.
REGIONAL CODE
VIOLATION
Disc does not match regional
code number.
Load a disc that matches the regional code number.
VIDEO SIGNAL
SYSTEM IS NOT
CORRECT
NTSC disc is loaded.
Load a PAL disc.
HI-TEMP
Protective circuit is activated to
high temperature.
Turn the power (main unit power when not connected)
OFF on the connected head unit and then turn the
power ON again. If the display still does not
disappear, leave the power OFF until the temperature
decreases and then turn the power ON again.
Picture is unclear
or noisy.
66
Specifications
Signal system .................................... NTSC/PAL
Horizontal resolution ......................... 500 lines or greater
Video output level .............................. 1Vp-p (75 ohms)
Video S/N ratio .................................. DVD: 60 dB
Audio S/N ratio .................................. DVD: 95 dB
CD: 93 dB
Frequency response ......................... DVD: 5 Hz to 22 kHz (±1 dB) (48 kHz sampling)
DVD: 5 Hz to 44 kHz (±1 dB) (96 kHz sampling)
CD: 5 Hz to 20 kHz (±1 dB)
Dynamic range .................................. DVD: 90 dB or greater
CD: 93 dB or greater
Wow & flutter ..................................... Below measurable limit
Channel separation ........................... 80 dB
Harmonic distortion ........................... 0.03%
Audio output ...................................... 800 mV
Power supply .................................... DC 14.4V (operating range: 11 to 16V)
Operating temperature range ............ –10° to +60°C
Weight ............................................... 1.6 kg (3 lbs. 8 oz)
External dimensions (W x H x D) ...... 178 x 50 x 185 mm (7” x 2” x 7-1/4”)
• For improvement purposes, specifications and design are subject to change without
notice.
• The illustrations in this manual may appear different from the actual product due to
printing conditions.
67
Functions of remote control unit buttons
Operating the DVA-5205P DVD Video Player
When operating the DVA-5205P set the DVD/AUDIO switch to the “DVD” side.
1
VOL
UP
L DN
VO
2
q
ENT
3
4
DISP
MENU
SET
5
SOURCE
LIST
GO TO
TITLE
BAND
RTN
SLOW
V.OUT
A. PROC DEFEAT
r
DISP.
TUNER
RPT
DISC
;
68
y
V. SEL
POWER
A. PROC
BAND
NTSC/PAL
o
CHG
t
8
9
p
u
i
e
MUTE
6
7
w
1
2
3
a
SUB T. ON/OFF AUDIO
4
5
6
ANGLE
7
DN
CLR
8
OP/
CL
0
9
UP
+10
s
1 Joy Stick (→ P13, 21, 24, 25, 26, 29,
30, 32, 34, 35, 36, 38, 40, 41, 42, 43,
44, 45, 46, 47, 48, 49, 50, 51, 52, 53,
54, 55)
Selects the items displayed on the
screen.
2 ENT button (→ P13, 17, 19, 21, 24,
25, 26, 27, 28, 29, 30, 32, 34, 35, 36,
38, 40, 41, 42, 43, 44, 45, 46, 47, 48,
49, 50, 51, 52, 53, 54, 55)
Determines the selected item.
3 Rotary Encoder (→ P11)
Adjusts the volume when only the
Digital Audio Processor is connected.
4 MENU button (→ P12, 13, 17, 18, 19,
21)
Displays the DVD menu.
SET button (→ P24, 25, 27, 29, 31,
33, 35, 37, 39)
Press and hold for 2 seconds to
summon the SET UP (initial setting)
screen.
5 : Button (→ P12, 13, 14, 15, 21)
Playback.
SLOW Button (→ P15)
Press and hold for 2 seconds for slow
motion playback.
.;;
Button (→ P14)
6
Seeks the start for video and audio
data.
Press and hold for 2 seconds for
Rewind of video and audio data.
7 ::. Button (→ P14)
Seeks the start for video and audio
data.
Press and hold for 2 seconds for Fast
Forward of video and audio data.
8 DISP. Button (→ P21, 22)
Displays the playback state on the
screen.
Functions of remote control unit buttons
9 RPT Button (→ P19)
Repeat playback.
p POWER Button (→ P10)
Turns the power ON and OFF.
NTSC/PAL Button (→ P11)
Press and hold for 5 seconds to
change between NTSC and PAL.
q DVD/AUDIO Switch (→ P8)
Used to switch between DVD and
Audio operation.
w GO TO Button (→ P16, 17, 18)
Used to go directly to start of selection.
TITLE Button (→ P12, 21)
Press and hold for 2 seconds to
display the Title Menu.
e RTN Button (→ P16, 17, 18, 25, 27,
29, 31, 33, 35, 37, 39, 41, 43, 44, 45,
46, 47, 49, 50, 51, 53, 55)
Used to return the selection screen
just prior to the present screen.
V.OUT Button (→ P23)
Used to switch between Video and
Audio output to the rear monitor.
r .. / ..: Button (→ P15)
Used for Pause and Frame-by-Frame
playback.
t ■ Button (→ P13)
Used to stop playback.
y A.PROC Button (→ P40, 41, 43, 44,
45, 47, 49, 50, 51, 53, 55)
Used to summon the processor
control screen when connected with
the Digital Audio Processor.
BAND Button (→ P41, 52)
Press and hold for 2 seconds to switch
the menu screen when controlling the
Digital Audio Processor.
u SUB T. Button (→ P20)
Press and hold for 2 seconds to
change the subtitles.
i –ON/OFF Button (→ P21)
Press and hold for 2 seconds to turn
the subtitles ON and OFF.
ANGLE
Button (→ P20)
o
Press and hold for 2 seconds to
change the angle.
; CLR Button (→ P16, 17, 18, 27)
Remove numbers (one character at a
time) that have been selected and
input.
Press and hold for 2 seconds. All the
characters which were selected and
input are erased.
a AUDIO Button (→ P19)
Press and hold for 2 seconds to
change the audio output.
10-Key
Pad (→ P11, 13, 16, 17, 18,
s
21, 25, 27, 28)
Used to input numbers.
Note: Operation may not be accepted depending
on the type of disc and the playback
conditions. At such a time the following
mark is displayed on the screen:
69
Functions of remote control unit buttons
Operating audio for the Alpine Ai-NET
When operating audio for the Alpine Ai-NET, set the DVD/AUDIO switch to the “AUDIO” side.
1
VOL
UP
L DN
VO
2
q
ENT
3
4
DISP
MENU
SET
5
SOURCE
LIST
GO TO
TITLE
BAND
RTN
SLOW
V.OUT
A. PROC DEFEAT
e
MUTE
6
7
w
r
DISP.
TUNER
RPT
DISC
CHG
t
8
9
p
y
V. SEL
POWER
NTSC/PAL
A. PROC
BAND
1 Joy Stick
Music Sensor/Fast Forward/Rewind/
Disc Change/Preset Selection/SEEK
2 ENT Button
Play/Pause
3 Rotary Encoder
Volume adjustment
4 DISP Button
Spectrum Analyzer display ON/OFF
5 SOURCE Button
Source switching
6 A.PROC Button
Audio Processor Switch
7 DEFEAT Button
Defeat Mode ON/OFF.
8 TUNER Button
Switches to Radio Mode.
9 DISC Button
Slave CD/MD mode switching.
p Power Button
Power ON/OFF switching.
q DVD/AUDIO Switch
Switching between DVD and Audio
operation.
w LIST Button
Changes the title list display.
Press and hold for 2 seconds to switch
to title input screen.
e BAND Button
Radio Band switching
r MUTE Button
Mute
t CHG Button
Switches to CHANGE Mode.
y V.SEL Button
V.SEL Switching
Note: Some controls may not be possible
depending on the audio device being used.
70
Memo
71
R
SERIAL NUMBER/NUMERO DE SERIE/NUMERO DE SERIE:
INSTALLATION DATE/DATE D’INSTALLATION/FECHA DE INSTALACION:
INSTALLATION TECHNICIAN/INSTALLATEUR/INSTALADOR:
PLACE OF PURCHASELIEU D’ACHAT/LUGAR DE ADQUISICION:
Alpine Electronics, Inc.
Tokyo office: 1-1-8 Nishi Gotanda,
Shinagawa-ku, Tokyo 141-8501, Japan
Tel.: (03) 3494-1101
Alpine Electronics of America, Inc.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Tel.: 1-800-ALPINE-1 (1-800-257-4631)
Alpine Electronics of Canada, Inc.
Suite 203, 7300 Warden Ave. Markham,
Ontario L3R 9Z6, Canada
Tel.: 1-800-ALPINE-1 (1-800-257-4631)
Alpine Electronics of Australia Pty. Ltd.
6-8 Fiveways Boulevarde Keysborough,
Victoria 3173, Australia
Tel.: (03) 9769-0000
Alpine Electronics GmbH
Kreuzerkamp 7-11 40878 Ratingen,
Germany
Tel.: 02102-45 50
Alpine Italia S.p.A.
Via C. Colombo 8, 20090 Trezzano Sul
Naviglio MI, Italy
Tel.: 02-48 47 81
Alpine Electronics France S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue De La Belle Etoile, Z.I. Paris Nord II
B.P. 50016 F-95945, Roissy,
Charles de Gaulle Cedex, France
Tel.: 01-48 63 89 89
Alpine Electronics of U. K., Ltd.
13 Tanners Drive, Blakelands,
Milton Keynes MK14 5BU, U.K.
Tel.: 01908-61 15 56
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal De Gamarra 36, Pabellón 32
01013 Vitoria (Alava) - Apdo. 133, Spain
Tel.: 34-45-283588
Sankei Kikaku Co., Ltd.
1-13-38, Hinodai,
Hino, Tokyo, Japan
Designed by ALPINE Japan
Printed in Japan (S)
68P30540Y28-O