Blaupunkt New Orleans MP58 Technical data

www.blaupunkt.com
Radio CD USB MP3 WMA
New Orleans MP58
7 648 009 310
Bedienungs- und Einbauanleitung
Operating and installation instructions
Mode d’emploi et de montage
Istruzioni d’uso e di installazione
Gebruiksaanwijzing en inbouwhandleiding
Bruks- och monteringsanvisning
Instrucciones de manejo e instalación
Instruções de serviço e de montagem
Betjenings- og monteringsvejledning
Instrukcja obsługi i montażowa
Návod k obsluze a k montáži
Návod na obsluhu a inštaláciu
Инструкция по эксплуатации и установке
01_NewOrleansMP58_de.indd 1
07.12.2007 14:56:47 Uhr
1
2
3
4
13 12
14
5
6
7
8
9
10
11
15
2
01_NewOrleansMP58_de.indd 2
07.12.2007 14:56:47 Uhr
Controls
1
button
to open the detachable control panel
(flip-release panel).
2 SRC button
Source selection between radio and CD
and (if connected or switched on) CD
changer, USB data carrier and AUX.
3 TRAF button
Short press: Switches traffic information standby on/off.
Long press: Switches convenient RDS
function on/off.
4 Arrow buttons
5 MENU•OK button
Short press: Calls up the menus for basic settings and confirms settings.
Ending the scan function.
Long press: Starts the Scan function.
; ESCAPE button
to exit the menus.
< BND button
Short press: Selects the FM memory
banks and the MW and LW wavebands.
Long press: Starts the Travelstore function.
= AUD button
Calls up the Audio menu: adjusts bass,
treble, centre, subout, balance and
fader.
Switching X-BASS on/off and adjusting it.
Selects an equalizer presetting.
>
button (eject)
to eject the CD from the device
? CD tray
6 On/Off button
Short press: Switches the device on. In
operation: Mutes the device.
Long press: Switches the device off.
7 Volume control
8 Display
9 Keys 1 - 6
: DIS button
Shows/hides time.
In MP3/WMA mode: Calls up the MP3
browse mode
46
02_NewOrleansMP58_gb.indd 46
07.12.2007 14:57:20 Uhr
About these instructions .................. 49
Symbols used................................ 49
Use as directed.............................. 49
Declaration of conformity................ 49
For your safety ................................ 50
If you are installing device yourself ..... 50
Observe the following! .................... 50
Cleaning instructions...................... 50
Disposal of old unit ........................ 50
Scope of delivery ............................. 51
Optional equipment
(not part of the scope of delivery) .... 51
Warranty......................................... 52
Service ........................................ 52
Detachable control panel ................. 52
Theft protection............................. 52
Detaching the control panel ............. 52
Attaching the control panel.............. 53
Switch-off time (OFF TIMER) ........... 53
Timeout function ........................... 53
Switching on/off .............................. 54
Switching on/off with the
On/Off button ............................... 54
Switching on/off using the vehicle
ignition......................................... 54
Switching off with detachable
control panel ................................. 54
Changing the welcome text.............. 54
Adjusting the volume ....................... 55
Setting the power-on volume ........... 55
Quickly reducing the volume (Mute).. 55
Telephone Audio/Navigation Audio ... 56
Switching the confirmation beep
on/off .......................................... 56
Automatic Sound ........................... 57
Radio mode ..................................... 58
Adjusting the tuner......................... 58
Switching to radio mode ................. 58
Convenient RDS functions (AF, REG) ....58
Selecting the waveband/
memory bank ................................ 59
Tuning into a station ....................... 59
Setting the sensitivity of station
seek tuning ................................... 60
Storing stations ............................. 60
Storing stations automatically
(Travelstore) ................................. 61
Listening to stored stations ............. 61
Scanning receivable stations (SCAN) ...61
Setting the scanning time ................ 61
Programme type (PTY) .................. 62
Traffic information........................... 63
Switching traffic information
priority on/off ............................... 63
Setting the volume for traffic
announcements............................. 64
CD mode ......................................... 64
Starting the CD mode ..................... 64
Selecting tracks ............................. 65
Fast searching (audible).................. 65
Random track play (MIX) ................. 65
Scanning tracks (SCAN).................. 65
Repeating tracks (REPEAT) ............. 66
Interrupting playback (PAUSE)......... 66
Displaying the time ........................ 66
Traffic announcements in CD mode.... 66
Ejecting a CD................................. 66
MP3/WMA mode ............................. 67
Preparing an MP3 data carrier ......... 67
Switching to MP3 mode .................. 68
Configuring the display ................... 69
Selecting a directory ...................... 69
Selecting tracks/files ...................... 70
Selecting directories and track in
MP3 browse mode ......................... 70
ENGLISH
Contents
47
02_NewOrleansMP58_gb.indd 47
07.12.2007 14:57:21 Uhr
Contents
Fast searching ............................... 71
Random track play (MIX) ................. 71
Scanning tracks (SCAN).................. 71
Repeating individual tracks or
whole directories (REPEAT) ............. 71
Interrupting playback (PAUSE)......... 72
CD-changer mode ............................ 72
Switching to CD changer mode ........ 72
Selecting CDs................................ 72
Selecting tracks ............................. 72
Fast searching (audible).................. 73
Repeating individual tracks or
whole CDs (REPEAT) ...................... 73
Random track play (MIX) ................. 73
Scanning all tracks on all CDs (SCAN)...73
Interrupting playback (PAUSE)......... 74
Displaying the time ........................ 74
Clock – Time.................................... 74
Adjusting the time .......................... 74
Selecting 12/24-hour clock mode .... 74
Displaying the time continuously
when the device is off and the
ignition is on ................................. 75
Sound ............................................. 75
Adjusting the bass (BASS) .............. 76
Adjusting the treble (TREBLE) ......... 76
Setting the left/right volume
distribution (BALANCE) .................. 77
Adjusting the front/rear volume
distribution (FADER) ...................... 77
Adjusting equalizer bass (E-BASS) ... 77
Adjusting equalizer middle
(E-MIDDLE) .................................. 78
Adjusting equalizer treble
(E-TREBLE) ................................... 78
Preamplifier output
(Preamp-Out/Sub-Out) .................... 79
Adjusting Sub-Out level and
Sub-Out cut-off frequency ............... 79
X-BASS ........................................... 80
Adjusting X-BASS boost (X-BASS) .... 80
Adjusting equalizer X-BASS (E-BASS)...80
Equalizer presettings (PRESETS) ...... 81
Adjusting the display settings ........... 81
Adjusting the display brightness....... 81
Setting the display illumination
colour .......................................... 81
Adjusting the display viewing angle ... 83
External audio sources ..................... 83
Adjusting the rear AUX input mode..... 84
Connecting other external audio
sources ........................................ 84
Bluetooth ..................................... 86
Restoring factory settings
(NORMSET) ..................................... 87
Technical data ................................. 88
Amplifier ...................................... 88
Tuner ........................................... 88
CD ............................................... 88
Pre-amp out .................................. 88
Input sensitivity ............................. 88
Installation instructions ................. 563
48
02_NewOrleansMP58_gb.indd 48
07.12.2007 14:57:21 Uhr
About these instructions
Use as directed
These instructions contain important information to easily and safely install and operate the device.
• Read these instructions carefully and
completely before using the device.
• Keep the instructions at a location so
that they are always accessible to all
users.
• Always pass on the device to third parties together with these instructions.
In addition, observe the instructions of the
devices used in conjunction with this device.
This device is intended for installation and
operation in a vehicle with 12 V vehicle system voltage and must be installed in a DIN
slot. Observe the performance limits in the
technical data. Repairs and installation, if
necessary, should be performed by a specialist.
ENGLISH
About these instructions
Declaration of conformity
The Blaupunkt GmbH declares that the device New Orleans MP58 complies with the
basic requirements and the other relevant
regulations of the directive 89/336/EWG.
Symbols used
These instructions employ the following
symbols:
CAUTION!
Warns about laser beam
CAUTION!
Warns about damaging the CD
drive
The CE mark confirms the compliance with EU directives.
쏅 Identifies a sequencing step
• Identifies a listing
49
02_NewOrleansMP58_gb.indd 49
07.12.2007 14:57:21 Uhr
For your safety
For your safety
The device was manufactured according to
the state of the art and established safety
guidelines. Even so, dangers may occur if
you do not observe the safety notes in these
instructions.
If you are installing device
yourself
You may only install the device yourself
if you are experienced in installing car
sound systems and are very familiar with
the electrical system of the vehicle. For this
purpose, observe the installation instructions at the end of these instructions.
Observe the following!
CAUTION
The device contains a Class 1 laser
that can cause injuries to your eyes.
Do not open the device and do not perform
any modifications.
In operation
• Operate the device only if traffic situation permits it! Stop at a suitable location to perform more extensive operations.
• Remove or attach the control panel only
while the vehicle is standing an.
• To protect your hearing, always listen
at a moderate volume. During mute
phases (e.g. when changing the audio source or CD in the CD changer),
changing the volume is not audible.
Do not increase the volume during this
mute phase.
•
Always listen at a moderate volume so
that you can always hear acoustic warning signals (e.g. police).
After operation
• The device is worthless to a thief without the control panel. Always remove
the control panel whenever you leave
the vehicle.
• Transport the control panel so that it is
protected against impacts and the contacts cannot become dirty.
Cleaning instructions
Solvents, cleaning and scouring agents as
well as dashboard spray and plastics care
product may contain ingredients that will
damage the surface of the device.
Use only a dry or slightly moistened cloth
for cleaning the device.
Disposal of old unit
Do not dispose of your old unit in
the household trash!
Use the return and collection systems available to dispose of the old device.
50
02_NewOrleansMP58_gb.indd 50
07.12.2007 14:57:21 Uhr
Bluetooth/USB interface
For Bluetooth applications, such as wireless
hands-free calling and Bluetooth streaming,
you can connect a Bluetooth interface. The
Bluetooth/USB interface provides an additional USB connection.
The Bluetooth/USB interface is also available in a C‘n‘C-capable version or can be
rendered C‘n‘C-capable with a software
update.
Information about the Bluetooth/USB interface is available at your Blaupunkt specialised dealer or on the Internet under
www.blaupunkt.com.
Scope of delivery
The scope of delivery includes:
1 Car sound system
1 Case for the control panel
1 Support frame
2 Disassembly tools
1 Guide pin
1 USB connecting cable
1 Operating instructions
Optional equipment
(not part of the scope of delivery)
Use only accessories approved
Blaupunkt.
by
Command and Control (C‘n‘C)
This device supports the command-andcontrol interface (C‘n‘C) of Blaupunkt. The
C‘n‘C interface allows an even more convenient control of devices and data carriers
that are connected via a C‘n‘C-capable interface with the car sound system (see also
Bluetooth/USB interface and iPod/USB interface).
Remote control
The steering wheel and/or handheld remote
control allows you to access the basic functions of your car sound system safely and
conveniently.
You cannot switch the device on/off using
the remote control!
You can find out from your Blaupunkt dealer
or on the Internet at www.blaupunkt.com
which remote controls can be used with
your car sound system.
ENGLISH
Scope of delivery
iPod/USB interface
With the iPod interface or the iPod/USB
interface, you can connect an iPod to the
radio device and conveniently control the
playback via the radio device. The iPod/
USB interface provides an additional USB
connection.
The iPod/USB interface is also available in
a C‘n‘C-capable version or can be rendered
C‘n‘C-capable with a software update.
Information about the iPod/USB interface is available at your Blaupunkt specialised dealer or on the Internet under
www.blaupunkt.com.
Amplifier
You can use all Blaupunkt and Velocity amplifiers.
CD changers
You can connect the following Blaupunkt
CD changers:
CDC A 03, CDC A 08 and IDC A 09.
51
02_NewOrleansMP58_gb.indd 51
07.12.2007 14:57:21 Uhr
Warranty
Warranty
We provide a manufacturer's warranty
for products bought within the European
Union. For devices purchased outside the
European Union, the warranty terms issued
by our respective responsible domestic
agency are valid.
The warranty terms can be called up under
www.blaupunkt.com or requested directly
from:
Blaupunkt GmbH
Hotline
Robert-Bosch-Str. 200
D-31139 Hildesheim, Germany
Service
In some countries, Blaupunkt offers a repair
and pick-up service.
Information about the availability of this
service in your country can be found at
www.blaupunkt.com.
If you want to take advantage of this service, you may request a pick-up service for
your device via the Internet.
Detachable control panel
Detachable control panel
Theft protection
The device is equipped with a detachable
control panel (flip-release panel) as a way
of protecting your equipment against theft.
The device is worthless to a thief without
this control panel.
Protect your device against theft by taking
the control panel with you whenever you
leave your vehicle. Do not leave the control
panel inside your vehicle - not even in a hiding place.
Notes:
• Never drop the control panel.
• Do not expose the control panel to direct sunlight or another heat source.
• Avoid direct skin contact with the
control panel’s electrical contacts. If
necessary, clean the contacts with a
lint-free cloth moistened with cleaning alcohol.
Detaching the control panel
쏅 Press the button 1.
The control panel opens to the bottom.
쏅 Hold the control panel by its right side
and then pull it straight out of the
bracket.
52
02_NewOrleansMP58_gb.indd 52
07.12.2007 14:57:22 Uhr
Detachable control panel
Attaching the control panel
2.
1.
쏅 Hold the control panel approximately
at a right angle to the device. (see figure, 1.)
쏅 Push the control panel into the guides
at the bottom edge of the device.
쏅 Push the control panel carefully into the
bracket until it clicks into place.
쏅 Fold the control panel up into the slot
and press it gently into place until it
clicks. (see figure, 2.)
Switch-off time (OFF TIMER)
After opening the control panel, the device
is switched off after an adjustable time. You
can set this time from 15 to 30 seconds.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VARIOUS MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until the display shows "OFF TIMER".
button 4 to open the
쏅 Press the
menu.
쏅 Set the time with the or button
4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
ENGLISH
Notes:
• The device is switched off after a time
preset by you. For further details,
please read the section "Switch-off
time (OFF TIMER)" in this chapter.
• The device remembers the audio
source played last for the next switchon.
• Any CD already inserted in the device
remains there.
Timeout function
The device features a time-out function
(time window).
For example, if you press the MENU•OK
button 5 and select a menu item, the device switches back after approx. 8 seconds
after the last button activation. The settings
performed are saved.
53
02_NewOrleansMP58_gb.indd 53
07.12.2007 14:57:22 Uhr
Switching on/off
Switching on/off
Changing the welcome text
There are various ways of switching the
device on/off:
When you switch on the device, an animation appears, followed by a welcome
text. The welcome text is factory set to
"BLAUPUNKT".
You can enter your own welcome text of up
to 9 characters.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VARIOUS MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
"ON MESSAGE" appears on the display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 to enter
the character at the current position.
쏅 Press the button 4 to change to the
next position.
쏅 Press the MENU•OK button 5 to
store the name.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Switching on/off with the On/Off
button
쏅 For switch-on, press the On/Off button
6.
The device switches on.
쏅 To switch off the device, press and hold
down the On/Off button 6 for longer
than 2 seconds.
The device switches off.
Note:
To protect the vehicle battery, the device will switch off automatically after
one hour if the ignition is off.
Switching on/off using the
vehicle ignition
The device will switch on/off simultaneously with the ignition if the device is correctly connected to the vehicle’s ignition as
shown in the installation instructions and
you did not switch the device off by pressing the On/Off button 6.
Switching off with detachable
control panel
쏅 Detach the control panel.
The devices switches off after the time set in
the "OFF TIMER" menu. For further details,
please read the section "Switch-off time
(OFF TIMER)" in the chapter "Detachable
control panel".
54
02_NewOrleansMP58_gb.indd 54
07.12.2007 14:57:22 Uhr
Adjusting the volume
You can adjust the volume in steps from 0
(off) to 50 (maximum).
To increase the volume,
쏅 turn the volume control 7 clockwise.
To decrease the volume,
쏅 turn the volume control 7 counterclockwise.
Setting the power-on volume
You can set the power-on volume.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VOLUME MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
"ON VOLUME" appears on the display.
button 4 to open the
쏅 Press the
menu.
쏅 Set a specific power-on volume with
the or button 4.
Or:
쏅 Press the button 4 to select the
"LAST VOLUME" setting.
To help you adjust the setting more easily,
the device will increase or decrease the
volume as you make your changes.
If you change the setting to "LAST VOLUME",
the volume when the device switches on will
be the same as the volume level that was set
the last time you switched the device off.
Note:
To protect your hearing, the power-on
volume is limited to the value "38" for
the setting "Last Volume". If the volume
was higher before switch-off, the value
is automatically set to "38" at switchon. This prevents an unintentionally
and unexpectedly high volume when
switching on the device.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
ENGLISH
Volume
Quickly reducing the volume
(Mute)
You can quickly reduce the volume to a
preset level.
쏅 Briefly press the On/Off button 6.
"MUTE" appears on the display.
Cancelling mute
To return to your previously set volume
level,
쏅 briefly press the On/Off button 6
again.
Adjusting the mute level
You can adjust the mute level.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VOLUME MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
55
02_NewOrleansMP58_gb.indd 55
07.12.2007 14:57:22 Uhr
Volume
쏅 Press the or button 4 repeatedly
until "MUTE LEVEL" appears on the display.
button 4 to open the
쏅 Press the
menu.
쏅 Set the mute level with the or button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Telephone Audio/Navigation
Audio
Muting during telephone/navigation
mode
If your car sound system is connected with
a cell phone or navigation system, the car
sound system is muted when a call is incoming or during a voice output of the navigation. The call or the voice output is played
back via the loudspeakers of the card sound
system. In order for this feature to work, the
mobile telephone or navigation system must
be connected to the car sound system as
described in the installation instructions.
You can find out from your Blaupunkt dealer
which navigation systems can be used with
your car sound system.
If a call is incoming or a navigation announcement takes place, the display shows
"TELEPHONE".
Adjusting the volume for telephone
audio/navigation audio
During a telephone call or a voice output of
the navigation, no traffic announcements
are switched through.
You can set the volume level at which the
telephone calls or navigation announcements are mixed in.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VOLUME MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "TEL VOLUME" appears on the display.
button 4 to open the
쏅 Press the
menu.
쏅 Set the desired volume with the or
button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Note:
You can use the volume control 7 to
adjust the volume of telephone calls
and navigation announcements whilst
you are listening to them.
Switching the confirmation beep
on/off
The system will output a confirmation beep
for some functions if you keep a button
pressed down for longer than 2 seconds,
for instance, when assigning a radio station
to a station preset button. You can switch
the beep on or off.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VOLUME MENU" appears on the
display.
56
02_NewOrleansMP58_gb.indd 56
07.12.2007 14:57:22 Uhr
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "BEEP ON" or "BEEP OFF" appears
on the display.
쏅 Switch the BEEP ON or OFF with the
button or 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Automatic Sound
쏅 Set the volume adjustment OFF or 1 - 5
with the or button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Note:
The optimum setting for the speeddependent volume adjustment feature
depends on how noise levels develop in
your particular vehicle. Determine the
perfect value for your vehicle using trial
and error.
ENGLISH
Volume
This function automatically adjusts the volume of the car sound system to the speed
driven and the associated driving noises.
For example, at an increased speed, the
volume is automatically increased to compensate for the increased driving noise
(e.g. due to airstream).
For this purpose, your vehicle must provide
the tachometer signal and the car sound
system must be connected as described in
the installation instructions.
You can adjust the automatic volume increase in 6 increments (OFF, 1-5).
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VOLUME MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly until "AUTO SOUND" appears on
the display.
button 4 to open the
쏅 Press the
menu.
57
02_NewOrleansMP58_gb.indd 57
07.12.2007 14:57:22 Uhr
Radio mode
Radio mode
This device is equipped with an RDS radio
receiver. Many of the receivable FM stations
broadcast a signal that not only carries the
programme but also additional information
such as the station name and programme
type (PTY).
The station name appears on the display as
soon as the tuner receives it.
Adjusting the tuner
To ensure proper functioning of the tuner,
the device must be set for the region in
which it is being operated. You can select
between Europe (EUROPE), America (USA)
and Thailand (THAI). The tuner is factory
set to the region in which it was sold. If you
experience problems with your radio reception, please check this setting.
Note:
The radio functions described in these
operating instructions refer to the tuner setting EUROPE.
쏅 Switch off the device by pressing the
On/Off button 6.
쏅 Hold the buttons 1 9 and DIS :
pressed at the same time and switch
on the device again with the On/Off
button 6.
The current setting (EUROPE, USA or THAI)
is displayed.
쏅 Select your tuner region with the or
button 4.
To save the setting,
쏅 press the MENU-OK button 5. The radio starts with the setting selected last
(radio, CD, CD changer, USB or AUX).
Switching to radio mode
If you are in CD, CD changer, USB or AUX
mode,
쏅 press the BND button <
OR
쏅 press the SRC button 2 repeatedly
until "TUNER" appears on the display.
Convenient RDS functions
(AF, REG)
The convenient RDS functions AF
(Alternative Frequency) and REGIONAL extend your radio’s range of functions.
• AF: If the RDS function is activated, the
radio automatically tunes into the best
receivable frequency for the station
that is currently set.
• REGIONAL: At certain times, some radio stations divide their programme
into regional programmes providing
different content. You can use the REG
function to prevent the car radio from
switching to alternative frequencies
that are transmitting different programme content.
Note:
REGIONAL must be activated/deactivated separately in the menu.
58
02_NewOrleansMP58_gb.indd 58
07.12.2007 14:57:23 Uhr
Radio mode
Note:
This setting is only possible in radio
mode.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "TUNER MENU" appears on
the display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "REG" appears on the display.
"OFF" or "ON" is displayed alongside
"REG".
To switch REGIONAL on/off,
쏅 press the or button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Switching the convenient RDS function
on/off
To switch the RDS functions AF and
REGIONAL on or off,
쏅 press and hold down the TRAF button
3 for longer than 2 seconds.
The display briefly shows the selected setting "RDS ON" or "RDS OFF".
Selecting the waveband/memory
bank
This device can receive programmes broadcast over the FM frequency range as well as
the MW and LW (AM) wavebands. There are
three memory banks available for the FM
waveband (FM1, FM2 and FMT) and one
for each of the MW and LW wavebands.
Six stations can be stored in each memory
bank.
To switch between the FM memory banks
(FM1, FM2 and FMT) and the MW and LW
wavebands,
쏅 press the BND button <.
ENGLISH
Switching REGIONAL on/off
Tuning into a station
There are various ways of tuning into a
station.
Automatic station seek tuning
쏅 Press the or button 4.
The radio tunes into the next receivable
station.
Note:
If the priority for traffic information is
active (the display shows the traffic
jam symbol), the next traffic information station is set.
Tuning into stations manually
You can also tune into stations manually.
Note:
You can only tune into stations manually if the convenient RDS function and
PTY are deactivated.
59
02_NewOrleansMP58_gb.indd 59
07.12.2007 14:57:23 Uhr
Radio mode
To change the set frequency in small increments,
쏅 briefly press the or button 4.
To change the set frequency quickly,
쏅 press and hold down the or button
4 for a longer period of time.
Browsing through broadcasting
networks (FM only)
If a radio station provides several programmes, you have the option of browsing
through its so-called "broadcasting network".
Note:
The convenient RDS function and PTY
must be activated before you can use
this feature.
쏅 Press the or button 4 to switch
to the next station on the broadcasting
network.
Note:
When using this feature, you will only
be able to switch to stations that you
have received once before already. To
receive the stations, use the Scan or
Travelstore function.
Setting the sensitivity of station
seek tuning
You can choose whether the radio should
only tune into stations providing good reception or whether it can also tune into
those with a weak reception.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "TUNER MENU" appears on
the display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "SENSITIVITY" appears on the display.
button 4 to open the
쏅 Press the
menu.
The display shows the currently set sensitivity level. "SENS HI6" indicates the highest sensitivity, "SENS LO1" the lowest.
쏅 Set the desired sensitivity with the
or button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Notes:
• This setting is only possible in radio
mode.
• The device stores the sensitivity value
set in the respective FM and AM waveband.
Storing stations
Storing stations manually
쏅 Select the desired memory bank (FM1,
FM2, FMT) or one of the wavebands
(MW or LW).
쏅 Tune into the desired station.
쏅 Press and hold down one of the station
buttons 1 - 6 9 for longer than 2 seconds to assign the station to that button.
60
02_NewOrleansMP58_gb.indd 60
07.12.2007 14:57:23 Uhr
Storing stations automatically
(Travelstore)
You can automatically store the six stations
offering the strongest reception in the region (FM only). The stations are stored in
the FMT memory bank.
Note:
Any stations that were previously
stored in this memory bank are deleted
in the process.
쏅 Press and hold down the BND button
< for longer than 2 seconds.
The storing procedure begins. "FM
TRAVELSTORE" appears on the display.
After the process has completed, the radio
will play the station that is stored in memory
location 1 of the FMT memory bank.
Note:
If the priority for traffic information is
active (the display shows the traffic
jam symbol), only traffic information
stations are stored.
Listening to stored stations
쏅 Select the memory bank or waveband.
쏅 Press one of the station buttons 1 - 6
9.
The stored station is played if it can be received.
Scanning receivable stations
(SCAN)
You can use the scan function to play all
the receivable stations briefly. You can set
the scanning time in the menu to between
5 and 30 seconds.
Starting SCAN
쏅 Press and hold down the MENU•OK
button 5 for longer than 2 seconds.
The radio scans the next receivable station.
"SCAN" and the current frequency or the
station name appear on the display.
Cancelling the SCAN and continuing to
listen to a station
쏅 Press the MENU•OK button 5.
Scanning stops and the radio continues
playing the station that it tuned into last.
ENGLISH
Radio mode
Setting the scanning time
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VARIOUS MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly until "SCAN TIME" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Set the desired scan time with the or
button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Note:
The defined scanning time is also applied by the system to scanning carried
out in CD and MP3 mode.
61
02_NewOrleansMP58_gb.indd 61
07.12.2007 14:57:23 Uhr
Radio mode
Programme type (PTY)
Besides transmitting the station name,
some FM stations also provide information on the type of programme that they are
broadcasting. Your car radio can receive
and display this information.
For example, the programme types can be:
CULTURE
TRAVEL
JAZZ
SPORT
SERVICE
POP
ROCK
SCIENCE
CHILDREN
You can use the PTY function to select stations of a particular programme type.
PTY-EON
If you specify the programme type and start
seek tuning, the radio will switch from the
current station to a station of the selected
programme type.
Notes:
• If the tuner does not find a station
that corresponds to the selected programme type, you will hear a beep and
"NOT AVAILABLE" appears briefly in
the display. The radio will then retune
to the station that it received last.
• If the tuned radio station or another
station on the broadcasting network
broadcasts your selected programme
type at a later point in time, the radio
will automatically switch from the currently tuned station or from CD, CDchanger, USB or AUX mode to the station whose programme type matches
the one you selected.
• If you do not want this PTY EON
switching, disable PTY. First, switch
to radio mode using the SRC button
2 or BND button <. In CD, CD
changer, USB or AUX mode, the Tuner
menu with the "PTY ON/ OFF" menu
item is not available.
Switching PTY on/off
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "TUNER MENU" appears on
the display.
button 4 to open the
쏅 Press the
menu.
"PTY" and the current setting appear in the
display.
쏅 Press the or button 4 to switch
PTY ON or OFF.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Selecting the PTY language
You can select the language for the display
of the programme types. Options include
DEUTSCH, ENGLISH and FRANÇAIS.
Note:
This setting is only possible in radio
mode.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "TUNER MENU" appears on
the display.
62
02_NewOrleansMP58_gb.indd 62
07.12.2007 14:57:23 Uhr
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "PTY LANGUAGE" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Set the desired language with the or
button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Selecting a programme type and
starting seek tuning
The current program type appears only
briefly on the display.
쏅 Press the or button 4.
쏅 During the display time, press the or
button 4 to change to a different
program type.
쏅 Press the or button 4 to start
seek tuning.
The radio will then tune into the next station
that it finds that corresponds to your selected programme type.
02_NewOrleansMP58_gb.indd 63
Traffic information
Traffic information
Your device is equipped with an RDS EON
receiving unit. EON (Enhanced Other
Network) ensures that whenever a traffic
announcement (TA) is broadcast, the system switches automatically from a station
that does not provide traffic reports to the
appropriate traffic information station within the broadcasting network that does.
Once the traffic announcement has been
played, the system will switch back to the
programme that you were listening to before.
ENGLISH
Radio mode
Switching traffic information
priority on/off
쏅 Press the TRAF button 3.
The priority for traffic announcements is activated if the display shows the traffic jam
symbol.
Notes:
You will hear a warning beep,
• if you leave the reception area of a
traffic information station that you
are currently listening to.
• If you leave the reception area of a
traffic information station that the
system is tuned into while you are
in the CD, CD changer, USB or AUX
mode, and the subsequent automatic
seek tuning cannot find a new traffic
information station.
• If you retune the radio from a traffic
information station to a station that
does not broadcast traffic information.
If you hear the warning beep, you can either switch off traffic information priority
or tune into a station that broadcasts traffic
information.
63
07.12.2007 14:57:23 Uhr
Traffic information
Setting the volume for traffic
announcements
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VOLUME MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly until "TA VOLUME" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Set the volume with the or button
4.
To help you adjust the setting more easily,
the device will increase or decrease the volume as you make your changes.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Note:
Using the volume control 7, you can
also adjust the volume during a traffic
announcement for the duration of that
announcement.
CD mode
CD mode
You can use this device to play standard
audio CDs, CD-Rs and CD-RWs with a diameter of 8 (mini CD) or 12 cm. To avoid
problems when playing self-burned CDs,
you should not burn CDs at speeds greater
than 16-speed.
Risk of severe damage to the
CD drive!
Non-circular shaped CDs may not be used.
We accept no responsibility for any damage
to the CD drive that may occur as a result
of the use of unsuitable CDs.
To ensure proper functioning, use only CDs
with the Compact-Disc logo. CDs with copyprotection may cause playback problems.
Blaupunkt cannot guarantee the proper
functioning of copy-protected CDs!
Besides being able to play audio CDs on this
device, you can also play CDs containing
MP3/WMA music files. For further information, please read the chapter entitled "MP3/
WMA mode".
Starting the CD mode
If no CD is in the drive, start the CD mode by
inserting a CD.
Note:
To insert a CD, you must open the control panel. With opened control panel,
the device is automatically switched off
64
02_NewOrleansMP58_gb.indd 64
07.12.2007 14:57:24 Uhr
after a preset switch-off time. Please
observe the following notes for this
purpose:
• If the device switches off before you
insert the CD in the drive tray, it is not
automatically drawn in. In this case,
remove the CD, close the control
panel, and switch the device on again
with the On/Off button 6 before you
attempt to reinsert the CD.
• If the CD has already been drawn in
and the device switches off before
you close the control panel, switch on
the device again with closed control
panel with the On/Off button 6.
• If necessary, increase the switchoff time to prevent the device from
switching off too fast. For further details, please read the section "Switchoff time (OFF TIMER)" in the chapter
"Detachable control panel".
To insert a CD,
쏅 press the button 1.
The control panel opens.
쏅 Gently insert the CD with its printed
side uppermost into the drive until you
feel some resistance.
The drive draws in the CD automatically.
You must not hinder or assist the drive as it
draws in the CD.
쏅 Gently close the control panel whilst
exerting a little pressure until you feel
it click into place.
The CD playback starts and "CD" is shown
on the display.
If a CD is already inserted in the drive,
쏅 press the SRC button 2 repeatedly
until "CD" appears on the display.
The playback starts at the position where it
was interrupted.
Selecting tracks
쏅 Press the or button 4 to select
the next or previous track.
If you press the button 4 once, the current track will be played again from the beginning.
ENGLISH
CD mode
Fast searching (audible)
To fast search backwards or forwards,
쏅 press and hold down the or button
4 until fast searching backwards/forwards begins.
Random track play (MIX)
쏅 Press the 5 MIX button 9.
"MIX ALL" appears briefly on the display and
the MIX symbol is displayed. The next randomly selected track will then be played.
Cancelling MIX
쏅 Press the 5 MIX button 9 again.
"MIX OFF" appears briefly on the display
and the MIX symbol disappears.
Scanning tracks (SCAN)
You can scan (briefly play) all the tracks on
the CD.
쏅 Press and hold down the MENU•OK
button 5 for longer than 2 seconds.
65
02_NewOrleansMP58_gb.indd 65
07.12.2007 14:57:24 Uhr
CD mode
The next track will then be scanned. "SCAN"
and the current track number are shown on
the display.
Note:
You can set the scan time. For further
information, please read the section
entitled "Setting the scanning time" in
the "Radio mode" chapter.
Cancelling Scan and continuing listening
to a track
To exit the scan process,
쏅 press the MENU•OK button 5.
The currently scanned track continues playing.
Repeating tracks (REPEAT)
If you want to repeat a track,
쏅 press the 4 RPT button 9.
"RPT TRK" appears briefly on the display,
and the REPEAT symbol is shown. The track
is repeated continuously until you deactivate Repeat.
Cancelling Repeat
If you want to cancel the repeat function,
쏅 press the 4 RPT button 9 again.
"RPT OFF" appears briefly on the display
and the REPEAT symbol disappears. Normal
playback is then resumed.
Interrupting playback (PAUSE)
쏅 Press the 3 button 9.
"PAUSE" appears on the display.
Cancelling pause
쏅 During the pause, press the button 3
9.
Playback is continued.
Displaying the time
To show or hide the time,
쏅 press the DIS button :.
Traffic announcements
in CD mode
If you wish to receive traffic announcements
in CD mode,
쏅 press the TRAF button 3.
The priority for traffic announcements is
activated if the display shows the traffic
jam symbol. For further details, please read
the chapter entitled "Traffic information".
Ejecting a CD
쏅 Press the button 1.
The control panel opens to the bottom.
쏅 Press the button > next to the CD
compartment.
The CD is ejected.
쏅 Remove the CD and close the control
panel.
Notes:
• If a CD is ejected, the drive will automatically draw it back in again after
approx. 10 seconds.
• You can also eject CDs whilst the device is switched off or whilst another
audio source is activated.
66
02_NewOrleansMP58_gb.indd 66
07.12.2007 14:57:24 Uhr
MP3/WMA mode
You can also use this car sound system to
play CD-Rs and CD-RWs as well as USB
data carriers that contain MP3 music files.
You can also play WMA files. This chapters
deals only with playing MP3 files since
the operation for MP3 and WMA files is
identical.
Notes:
• WMA files with Digital Rights
Management (DRM) from online music shops cannot be played with this
device.
• WMA files can only be played back
safely if they were created with
Windows Media Player version 8 or
later.
Preparing an MP3 data carrier
Preparing an MP3 CD
The various combinations of CD burners,
CD burning software and CD blanks may
lead to problems arising with the device’s
ability to play certain CDs. If problems occur with your own burned CDs, you should
try another brand of CD blank or choose another colour of CD blank.
The format of the CD must be ISO 9660
Level 1/Level 2 or Joliet. Other formats cannot be played reliably.
When creating (coding) MP3/WMA files
from audio files, you should use bit rates
from 32 to 320 kbit/s for MP3 files or 32 to
192 kbps for WMA files.
This device supports up to 999 tracks in
99 directories. The directories and tracks
on the CD can be selected individually.
ENGLISH
MP3/WMA mode
D01
A
D02
D03
T001
T002
T003
T004
T005
T001
T002
T003
T004
T005
T006
D04
T001
T002
T003
T004
T005
T006
T007
T008
T009
T010
T011
B
A Directories
B Tracks · Files
You can name each directory using a PC.
The device is capable of displaying the directory name. Name the directories and
tracks/files using your CD burner software.
The software’s instruction manual will provide details on how to do this.
Notes:
• When naming files (directories and
tracks) you should avoid using accents and special characters.
67
02_NewOrleansMP58_gb.indd 67
07.12.2007 14:57:24 Uhr
MP3/WMA mode
• If you use file names with more than
16 characters (including ".MP3" or
".WMA"), the maximum number of
tracks and directories is reduced.
If you like your files to be in the specific order, save the files on the data carrier in the
desired sequence in which you want to play
them later. The devices plays back the files
in the order in which they were physically
stored on the data carrier.
To play back files in this device, the MP3 files
must have the file extension ".MP3" and the
WMA files the file extension ".WMA".
Notes:
To ensure uninterrupted playback,
• do not try changing the file extension
to ".MP3" of any files other than MP3
files and then attempt to play them!
The device will ignore these invalid
files during playback.
• Do not use "mixed" CDs containing
both non-MP3 data and MP3 tracks
(the device only reads MP3 files during MP3 playback).
• do not use mix-mode CDs containing
both CD-audio tracks and MP3 tracks.
If you attempt to play a Mix Mode CD,
only the CD audio tracks are played.
Preparing a USB data carrier
For the device to recognise a USB data carrier, it must be specified as mass storage
device and formatted using the FAT16 or
FAT32 file system and contain MP3 or WMA
files.
You can created up to 1,500 files on a USB
data carrier (directories and tracks). The
directories and tracks can be selected individually with this device. If you use file
names with more than 24 characters (including ".MP3" or ".WMA"), this maximum
number of files is reduced.
Blaupunkt cannot guarantee the proper
functioning of all USB data carriers available on the market.
MP3 ID3 tags
MP3 tracks can contain additional information such as the artist, album and track
name (ID3 tags). This device can display
ID3 tags of version 1 and 2.
Switching to MP3 mode
Activating the MP3 mode of CD
For an MP3 CD, the MP3 mode is activated
in the same way as the normal CD mode.
For further information, please read the
section entitled "Starting the CD mode" in
the "CD mode" chapter.
Connect USB data carrier and start MP3
mode
To be able to connect a USB data carrier
(e.g. a USB stick or USB hard disk), the
supplied USB cable must be connected to
the rear side of the device as described in
the installation instructions. This cable can
be routed, for example, to the glove compartment or a suitable place of the center
console.
68
02_NewOrleansMP58_gb.indd 68
07.12.2007 14:57:24 Uhr
MP3/WMA mode
Configuring the display
Displaying the time
쏅 Press the DIS button : repeatedly
until the time appears.
Displaying artist and album name
You can display the artist and album name
of the current track.
To show or hide the artist and album name,
쏅 press the MENU•OK button 5.
The display shows "MENU".
쏅 Press the or button 4 repeatedly
until "VARIOUS MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly until "MP3-INFO ON" or "MP3-INFO
OFF" appears on the display.
쏅 Press the or button 4 to toggle
between "MP3-INFO ON" and "MP3INFO OFF".
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Note:
Artist and album name are a component of the MP3 ID3 tag of version 1
and version 2 and can only be displayed
if they were stored with the MP3 files.
For further details, please read the
instructions of your PC MP3 software
or burner software.
ENGLISH
Note
Always switch off the device before
connecting or disconnecting the USB
data carrier so that the data carrier is
correctly registered and unregistered.
쏅 Connect the USB data carrier with the
USB cable.
As soon as a USB data carrier is connected,
it can be selected with the SRC button 2.
The display shows "USB".
Selecting a directory
To move up or down to another directory,
쏅 press the or 4 button once or
several times.
Notes:
• The device will automatically skip any
directories that do not contain MP3
files.
• The device treats all directories and
subdirectories as if they were located
on one level. Repeatedly pressing the
or button 4 will also bring you
to all subdirectories.
69
02_NewOrleansMP58_gb.indd 69
07.12.2007 14:57:24 Uhr
MP3/WMA mode
Selecting tracks/files
To move up or down to another track/file in
the current directory,
쏅 press the or 4 button once or
several times.
button 4 once, the
If you press the
current track will be played again from the
beginning.
Selecting directories and track
in MP3 browse mode
In MP3 browse mode, the tracks and directories of the MP3 data carrier are displayed
as they are physically stored on the data carrier in directories and subdirectories. For
this purpose, a three-line display is shown
in MP3 browse mode. This display shows all
the tracks and subdirectories of the current
directory as a list. You can select and play a
track in this list or select and open a subdirectory. In addition, you can change to the
higher level directory if you are currently in
a subdirectory.
Selecting and exiting MP3 browse mode
To change from standard display to MP3
browse mode,
쏅 press the DIS button : repeatedly
until the three-line display of the MP3
browse mode appears.
The three-line display shows a list of the
subdirectories and the name of the current
directory. The current track is identified in
the list by a right arrow in front of the track
name.
To exit MP3 browse mode again,
쏅 press the DIS button :.
The standard display appears.
Note
In MP3 browse mode, fast searching
and the functions MIX, REPEAT and
SCAN are not available.
Selecting a track or subdirectory
To move up or down in the list to the desired
track or subdirectory,
쏅 press the or button 4 once or
several times.
The selected track is displayed in inverted
mode.
Notes:
• If the list contains more than 3 tracks
and subdirectories, the list is automatically scrolled up or down while
you are navigating in the list. You
reached the beginning or end of the
list if the up or down arrow on the
right edge of the list is no longer being displayed.
or
• Press and hold down the
button 4 to quickly scroll through
the list.
To play the selected track or open the
selected subdirectory,
쏅 press the button 4.
The playback of the selected track starts
or the contents of the selected subdirectory
is displayed.
70
02_NewOrleansMP58_gb.indd 70
07.12.2007 14:57:24 Uhr
MP3/WMA mode
Note:
If no additional higher level directory is
displayed after pressing the button
4, you have reached the top level of
the data carrier.
Fast searching
To fast search backwards or forwards,
쏅 press and hold down the or button
4 until fast searching backwards/forwards begins.
Random track play (MIX)
To play the tracks in the current directory in
random order,
쏅 press the 5 MIX button 9 once or several times until "MIX DIR" is displayed.
The display shows the MIX symbol.
To play the tracks contained in all the directories on the MP3 data carrier in random
order,
쏅 press the 5 MIX button 9 once or several times until "MIX ALL" is displayed.
The display shows the MIX symbol.
Cancelling MIX
To cancel MIX,
쏅 press the 5 MIX button 9 once or several times until "MIX OFF" is displayed.
The MIX symbol disappears from the display.
Scanning tracks (SCAN)
You can scan (briefly play) all the tracks on
the MP3 data carrier.
쏅 Press and hold down the MENU•OK
button 5 for longer than 2 seconds.
The next track will then be scanned. "SCAN"
and the current track name are shown on
the display.
ENGLISH
Changing to the higher level directory
To change from the current to the higher
level directory,
쏅 press the button 4.
Note:
You can set the scan time. For further
information, please read the section
entitled "Setting the scanning time" in
the "Radio mode" chapter.
Cancelling Scan and continuing listening
to a track
쏅 Briefly press the MENU•OK button
5.
The currently scanned track continues playing.
Repeating individual tracks or
whole directories (REPEAT)
To play the current track repeatedly,
쏅 press the 4 RPT button 9 once or several times until "RPT TRK" is displayed.
The display shows the REPEAT symbol.
To repeatedly play the entire directory,
쏅 press the 4 RPT button 9 once or several times until "RPT DIR" is displayed.
The display shows the REPEAT symbol.
71
02_NewOrleansMP58_gb.indd 71
07.12.2007 14:57:25 Uhr
MP3/WMA mode
Cancelling Repeat
To stop the current track or current directory from being repeated,
쏅 press the 4 RPT button 9 once or several times until "RPT OFF" is displayed.
The REPEAT symbol disappears from the
display.
Interrupting playback (PAUSE)
To stop the playback,
쏅 press the 3 button 9.
"PAUSE" appears on the display.
Cancelling pause
쏅 During the pause, press the button 3
9.
Playback is continued.
CD changer mode
CD-changer mode
Notes:
• Before connecting a CD changer,
check the mode of the AUX input on
the rear side and, if necessary, select the setting "CDC ON". For further details, please read the section
"Adjusting the rear AUX input mode"
in the chapter "External audio sources".
• Information on handling CDs, inserting CDs and operating the CD changer
can be found in the operating instructions supplied with your CD changer.
Switching to CD changer mode
쏅 Press the SRC button 2 repeatedly
until the display shows "CDC / AUX".
The device starts playing the first CD that
the CD changer detects.
Selecting CDs
To move up or down to another CD,
쏅 press the or 4 button once or
several times.
Note:
The device will ignore empty CD slots in
the changer and slots containing invalid
CDs.
Selecting tracks
To move up or down to another track on the
current CD,
쏅 press the or 4 button once or
several times.
72
02_NewOrleansMP58_gb.indd 72
07.12.2007 14:57:25 Uhr
Fast searching (audible)
Random track play (MIX)
To fast search backwards or forwards,
쏅 press and hold down the or button
4 until fast searching backwards/forwards begins.
To play the tracks on the current CD in random order,
쏅 press the 5 MIX button 9 once or several times until "MIX CD" is displayed.
The display shows the MIX symbol.
To play the tracks on all inserted CDs in
random order,
쏅 press the 5 MIX button 9 once or several times until "MIX ALL" is displayed.
The display shows the MIX symbol.
Repeating individual tracks or
whole CDs (REPEAT)
To repeat the current track,
쏅 press the 4 RPT button 9 once or
several times until "RPT TRACK" is displayed.
The display shows the REPEAT symbol.
To repeat the current CD,
쏅 press the 4 RPT button 9 once or
several times until "RPT DISC" is displayed.
The display shows the REPEAT symbol.
Cancelling Repeat
To stop the current track or current CD from
being repeated,
쏅 press the 4 RPT button 9 once or several times until "RPT OFF" is displayed.
The REPEAT symbol disappears from the
display.
ENGLISH
CD-changer mode
Cancelling MIX
쏅 Press the 5 MIX button 9 once or several times until "MIX OFF" is displayed.
The MIX symbol disappears from the display.
Scanning all tracks on all CDs
(SCAN)
To scan all the tracks of all inserted CDs in
ascending order for approx. 10 seconds
each,
쏅 press and hold down the MENU•OK
button 5 for longer than 2 seconds.
The next track will then be scanned. "SCAN"
and the current track number are shown on
the display.
Stopping Scan
To stop scanning,
쏅 briefly press the MENU•OK button
5.
The currently played track will then continue to be played normally.
73
02_NewOrleansMP58_gb.indd 73
07.12.2007 14:57:25 Uhr
CD changer mode
Clock – Time
Interrupting playback (PAUSE)
Clock – Time
쏅 Press the 3 button 9.
"PAUSE" appears on the display.
Adjusting the time
Cancelling pause
쏅 During the pause, press the button 3
9.
Playback is continued.
Displaying the time
To show or hide the time,
쏅 press the DIS button :.
To set the time,
쏅 press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "CLOCK MENU" appears on
the display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly until "CLOCK SET" appears on the
display.
쏅 Press the
button 4 to open the
menu.
The time appears on the display. The hours
and minutes can be adjusted.
쏅 Set the time with the or button
4.
To switch between hours and minutes,
쏅 press the or button 4.
쏅 Press the MENU•OK button 5 to confirm the adjusted time.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Selecting 12/24-hour clock
mode
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "CLOCK MENU" appears on
the display.
74
02_NewOrleansMP58_gb.indd 74
07.12.2007 14:57:25 Uhr
Clock – Time
Displaying the time continuously
when the device is off and the
ignition is on
To display the time when the device is off
and the vehicle ignition is on,
쏅 press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "CLOCK MENU" appears on
the display.
button 4 to open the
쏅 Press the
menu.
"CLOCK" and the current setting appear on
the display.
쏅 Press the or button 4 to switch
the display between CLOCK ON and
CLOCK OFF.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Sound
You can adjust the sound settings (bass,
middle and treble) separately for each
source (radio, CD, CD changer, USB and
AUX). The volume distribution (balance and
fader) and X-BASS settings apply to all the
audio sources.
This device features a digital 3-band equalizer. This equalizer allows for selecting one
frequency each for bass, treble and middle
and to adjust the level for the selected frequency between -7 and +7. In addition, you
can adjust the quality factor for bass and
middle.
ENGLISH
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly until "24HR MODE" or "12HR MODE"
appears on the display.
쏅 Press the or button 4 to switch
between the modes.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Sound
Note
The quality factor determines the filter
quality of the equalizer, i.e. the edge
steepness and filter bandwidth, dependent upon the characteristic frequency.
A low quality factor means a low edge
steepness and a high filter bandwidth;
a high quality factor means a high edge
steepness and a low filter bandwidth.
The following table shows an overview of
the setting options:
BASS
TREBLE
MIDDLE
GAIN
x
x
x
Frequency
(FREQ)
x
x
x
Quality
factor
(QUALITY)
x
–
x
75
02_NewOrleansMP58_gb.indd 75
07.12.2007 14:57:25 Uhr
Sound
To adjust the bass and treble levels quickly
and conveniently for a simple sound adjustment, these settings are located directly in
the AUDIO menu. You can adjust the level in
the submenus BASS and TREBLE:
Adjusting the bass (BASS)
AUDIO
Level
Frequency
Quality
factor
BASS
TREBLE
x
x
FREQ
FREQ
FREQ
QUALITY
–
QUALITY
GAIN
To adjust the bass and treble levels,
please read the chapters "Adjusting the
bass (BASS)" and "Adjusting the treble
(TREBLE)".
To fully utilise the equalizer functions, all other settings can be made in the ENHANCED
MENU submenu of the AUDIO menu. In
the submenus E-BASS (equalizer bass),
E-TREBLE (equalizer treble) and E-MIDDLE
(equalizer middle), you can perform the settings FREQ (frequency) and QUALITY (quality factor, for bass and middle only) as well
as GAIN (level, for middle only):
AUDIO
BASS
Level
Frequency
Quality
factor
To set the additional equalizer functions,
please read the chapters "Adjusting equalizer bass (E-BASS)", "Adjusting equalizer
middle (E-MIDDLE)" and "Adjusting equalizer treble (E-TREBLE)".
TREBLE
x
x
GAIN
FREQ
FREQ
FREQ
QUALITY
–
QUALITY
E-BASS
E-TREBLE
E-MIDDLE
쏅 Press the AUD button =.
"BASS" appears on the display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 to adjust
the level between -7 and +7.
To exit the menu,
쏅 press the ESCAPE button ;.
Adjusting the treble (TREBLE)
쏅 Press the AUD button =.
"BASS" appears on the display.
쏅 Press the or button 4 repeatedly
until "TREBLE" appears on the display.
쏅 Press the
button 4 to open the
menu.
쏅 Press the or button 4 to adjust
the level between -7 and +7.
To exit the menu,
쏅 press the ESCAPE button ;.
ENHANCED MENU
AUDIO
76
02_NewOrleansMP58_gb.indd 76
07.12.2007 14:57:25 Uhr
Setting the left/right volume
distribution (BALANCE)
Adjusting equalizer bass
(E-BASS)
To adjust the left/right volume distribution,
쏅 press the AUD button =.
"BASS" appears on the display.
or button 4 repeat쏅 Press the
edly until "BALANCE" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 to adjust
the balance (right/left).
To exit the menu,
쏅 press the ESCAPE button ;.
You can select 1 of 4 bass frequencies
(60 Hz, 80 Hz, 100 Hz, 200 Hz) and set the
quality factor between 1.0 and 2.0.
Adjusting the front/rear volume
distribution (FADER)
To adjust the front/rear volume distribution,
쏅 press the AUD button =.
"BASS" appears on the display.
쏅 Press the or button 4 repeatedly
until "FADER" appears on the display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 to adjust
the fader (front/rear).
To exit the menu,
쏅 press the ESCAPE button ;.
Note:
For further information on setting the
bass level, please read the section entitled "Adjusting the bass (BASS)" in this
chapter.
ENGLISH
Sound
Adjusting bass frequency and quality
factor
쏅 Press the AUD button =.
"BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "ENHANCED MENU" appears
on the display.
쏅 press the button 4.
"E-BASS" appears on the display.
button 4 to open the
쏅 Press the
E-Bass menu.
"FREQ" appears on the display.
쏅 Press the or button 4 to change
between the setting options "FREQ"
(bass frequency) and "QUALITY" (quality factor).
button 4 to open the
쏅 Press the
menu.
쏅 Set the bass frequency and quality factor each with the or button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
77
02_NewOrleansMP58_gb.indd 77
07.12.2007 14:57:26 Uhr
Sound
Adjusting equalizer middle
(E-MIDDLE)
Adjusting equalizer treble
(E-TREBLE)
You can select one of 4 middle frequencies
(500 Hz, 1,000 Hz, 1,500 Hz, 2,500 Hz)
and set the level for the selected frequency
between -7 and +7. You can also set the
quality factor between 0.5 and 1.25.
You can select 1 of 4 treble frequencies
(10 kHz, 12.5 kHz, 15 kHz, 17.5 kHz).
Adjusting middle frequency, level and
quality factor
쏅 Press the AUD button =.
"BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "ENHANCED MENU" appears
on the display.
쏅 Press the button 4.
"E-BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "E-MIDDLE" appears on the
display.
button 4 to open the
쏅 Press the
E-Middle menu.
"GAIN" appears on the display.
쏅 Press the or button 4 to switch
between "GAIN" (level), "FREQ" (middle frequency) and "QUALITY" (quality
factor).
button 4 to open the
쏅 Press the
menu.
쏅 Set the level, middle frequency and
or
quality factor each with the
button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Note:
For further information on setting the
treble level, please read the section entitled "Adjusting the treble (TREBLE)"
in this chapter.
Adjusting the treble frequency
쏅 Press the AUD button =.
"BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "ENHANCED MENU" appears
on the display.
쏅 press the button 4.
"E-BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "E-TREBLE" appears on the
display.
button 4 to open the
쏅 Press the
E-Treble menu.
"FREQ" appears on the display.
button 4 to open the
쏅 Press the
menu.
쏅 Set the treble frequency with the or
button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
78
02_NewOrleansMP58_gb.indd 78
07.12.2007 14:57:26 Uhr
Preamplifier output
(Preamp-Out/Sub-Out)
You can use the preamplifier outputs
(Preamp-Out) of the car sound system to
connect external amplifiers. In addition,
you can connect an amplifier for operating
a subwoofer to the integrated dynamic lowpass filter of the device (level and cut-off
frequency can be adjusted).
For this purpose, the amplifiers must be
connected as described in the installation
instructions.
쏅 Press the or button 4 to switch
between the setting options "GAIN"
(level) and "FREQ" (cut-off frequency).
button 4 to open the
쏅 Press the
menu.
쏅 Set the level and cut-off frequency with
the or button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
ENGLISH
Preamplifier output
Adjusting Sub-Out level and SubOut cut-off frequency
The sub-out level can be adjusted in 8 increments (0 to +7). You can also select 1 of 3
cut-off frequencies: 80 Hz, 120 Hz, Hz and
160 Hz.
쏅 Press the AUD button =.
"BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "ENHANCED MENU" appears
on the display.
쏅 press the button 4.
"E-BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "SUBOUT" appears on the
display.
쏅 Press the button 4 to open the SubOut menu.
"GAIN" appears on the display.
79
02_NewOrleansMP58_gb.indd 79
07.12.2007 14:57:26 Uhr
X-BASS
X-BASS
X-Bass allows you to increase the bass at
low volume.
The selected X-Bass setting is effective for
all audio sources (radio, CD, CD changer,
USB or AUX).
For X-BASS, either the basic function
X-BASS boost or the equalizer X-BASS
(E-XBASS) is available. The basic function
allows you to adjust the X-BASS boost. The
equalizer X-BASS also allows you to select
an X-BASS frequency.
Adjusting X-BASS boost
(X-BASS)
The X-BASS increase can be set in increments of 0 to 3.
"0" means that the X-BASS function is
switched off.
쏅 Press the AUD button =.
"BASS" appears on the display.
쏅 Press the or button 4 repeatedly
until "X-BASS" appears on the display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 to adjust
the X-BASS boost.
To exit the menu,
쏅 press the ESCAPE button ;.
Adjusting equalizer X-BASS
(E-BASS)
You can adjust an increase between 0
(X-Bass function off) and 3 for X-Bass. You
can select whether the increase should affect the entire X-BASS frequency range
(setting "FLAT") or purposefully only one
of three X-BASS frequencies (400 Hz,
800 Hz, 2400 Hz).
쏅 Press the AUD button =.
"BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "ENHANCED MENU" appears
on the display.
쏅 press the button 4.
"E-BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "E-XBASS" appears on the
display.
button 4 to open the
쏅 Press the
E-XBASS menu.
"GAIN" appears on the display.
쏅 Press the or button 4 to switch
between the setting options "GAIN"
(boost) and "FREQ" (X-BASS frequency).
button 4 to open the
쏅 Press the
menu.
쏅 Set the boost and the X-BASS frequency each with the or button 4.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
80
02_NewOrleansMP58_gb.indd 80
07.12.2007 14:57:26 Uhr
Equalizer presettings
(PRESETS)
This device features an equaliser in which
the settings for the music genres "ROCK",
"POP" and "CLASSIC" are already programmed.
To select an equaliser setting,
쏅 press the AUD button =.
"BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "ENHANCED MENU" appears
on the display.
쏅 press the button 4.
"E-BASS" appears on the display.
쏅 Press the or button 4 repeatedly until "PRESETS" appears on the
display.
button 4 to open the
쏅 Press the
presets menu.
쏅 Press the or button 4 to select
one of the presettings "ROCK", "POP",
"CLASSIC" or select "P-EQ OFF" to deactivate the presetting.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Adjusting the display settings
Adjusting the display
settings
Adjusting the display brightness
If your car sound system is installed as described in the installation instructions and
your vehicle features the corresponding
connection, the display brightness for day
and night is switched by switching the vehicle lighting on or off. You can adjust the
display brightness separately for night and
day in steps ranging from 1 - 16.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "DISPLAY MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "DIM DAY" or "DIM NIGHT" appears
on the display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 to switch
between the brightness levels.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
ENGLISH
Equalizer presettings
Setting the display illumination
colour
For the display illumination, you can select a colour from the RGB spectrum (redgreen-blue) or mix using the colours red
and green, select a colour during the colour scan or switch on a constant colour
change.
81
02_NewOrleansMP58_gb.indd 81
07.12.2007 14:57:26 Uhr
Adjusting the display settings
Mixing a colour for the display
illumination
To customise the display illumination to suit
your tastes you can mix a colour yourself
using the three primary colours red, green
and blue (RGB).
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "DISPLAY MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "USER COLOUR" appears.
쏅 Press the button 4 to open the RGB
menu.
"R", "G", and "B" are displayed with the current values. The setting for "R" is activated.
You can adjust a value from 0 to 16 each for
every colour component.
쏅 Press the or button 4 to adjust
the value of a colour component.
쏅 Press the or button 4 to switch
between the colour components.
When you have finished making your changes,
쏅 press the MENU•OK button 5.
쏅 Press the ESCAPE button ; to exit
the menu.
Selecting a display illumination during a
colour scan
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "DISPLAY MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "COLOUR SCAN" appears.
쏅 Press the button 4 to start the colour seek.
The device starts changing the display illumination colour.
To select the currently set colour,
쏅 press the MENU•OK button 5.
With the button 4, you can start the
colour seek again and select a different colour.
If you found and selected the desired colour,
쏅 press the ESCAPE button ;.
Switching the constant colour change
for the display illumination on/off
(SCAN)
You can select a constant colour change as
the colour of the display illumination. If the
colour change is activated, the display colour changes constantly. The colour change
is switched on or off in the menu.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "DISPLAY MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
82
02_NewOrleansMP58_gb.indd 82
07.12.2007 14:57:27 Uhr
쏅 Press the or button 4 repeatedly
until "CONTSCAN ON" or "CONTSCAN
OFF" appears on the display.
쏅 Press the or button 4 to toggle
between ON (colour change on) and
OFF (colour change off).
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Adjusting the display viewing
angle
The angle at which you, the driver, looks at
the display is dependent upon, among other things, the installation position of the device and your seating position and physical
size. You can increase or decrease the display contrast to perfectly read the display
from your viewing angle.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "DISPLAY MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly until "ANGLE ADJ" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 to adjust
the display contrast between -6 and
+6.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
External audio sources
External audio sources
You can connect different external audio
sources to the device via the rear AUX input:
• C‘n‘C-capable devices from the
Blaupunkt accessories programme
(e.g. a C‘n‘C-capable Bluetooth/USB or
iPod/USB interface).
• CD changer
• Other external audio sources, such as
portable CD players, MiniDisc players,
MP3 players or a non-C‘n‘C-capable
Blaupunkt interface.
The C‘n‘C interface from Blaupunkt (C‘n‘C
= Command and Control) allows an even
more convenient control of devices and
data carriers that are connected to the car
sound system via a C‘n‘C-capable Blaupunkt
interface.
This device is factory set for the connection of C‘n‘C-capable Blaupunkt accessory
devices. If you want to connect a non-C‘n‘Ccapable device, such as a CD changer or
another external audio source, please perform the settings described in the following
sections.
ENGLISH
Adjusting the display settings
Note:
You can also connect several C‘n‘C-capable Blaupunkt interface to the device. For the device to be able to differentiate the different interfaces, you can
assign individual device numbers to the
interfaces in the "VARIOUS" submenu
under the "C‘N‘C" menu item.
Explanations about the functions of
this menu item can be found in the operating instructions of the Blaupunkt
interface.
83
02_NewOrleansMP58_gb.indd 83
07.12.2007 14:57:27 Uhr
External audio sources
Adjusting the rear AUX input
mode
You can select between these settings for
the rear AUX input:
• CDC OFF:
C‘n‘C mode for C‘n‘C-capable Blaupunkt
interfaces.
• CDC ON:
Mode for non-C‘n‘C-capable Blaupunkt
interfaces, CD changers and other external audio sources.
The C‘n‘C mode is activated by default.
To toggle between "CDC OFF" and "CDC
ON",
쏅 press the MENU•OK button 5.
The display shows "MENU".
쏅 Press the or button 4 repeatedly
until "VARIOUS MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly until "CDC OFF" or " CDC ON" is
displayed.
쏅 Press the or button 4 to toggle
between "CDC OFF" and "CDC ON".
If you change the setting, the device briefly
switches off and back on again with the selected setting (Reset).
Connecting other external audio
sources
If no C‘n‘C-capable Blaupunkt accessory
device and no CD changer is connected to
the device, you can connect other external
audio sources via the rear AUX input, such
as portable CD players, MiniDisc players or
MP3 players.
Note:
An adapter cable is needed to connect
an external audio source via the rear
AUX input. You can obtain this cable
(Blaupunkt no.: 7 607 897 093) from
your Blaupunkt dealer.
If you want to connect such an external audio source, proceed as follows:
1. Check the mode of the rear AUX input
and, if necessary, select the setting
"CDC ON". For further details, please
read the section "Adjusting the rear
AUX input mode" in this chapter.
2. Connect the external audio source to
the rear AUX input while the device is
switched off.
3. In the menu of the device, switch on the
external audio source. For further details, please read the following section,
"Switching the external audio source
on/off and selecting it".
4. If necessary, make additional settings
for the external audio source. For further details, please read the additional
sections in this chapter.
Switching the external audio source
on/off and selecting it
If you connected an external audio source
to the rear AUX input, you must activate the
AUX input in the menu. Afterwards, you can
select the external audio source with the
SRC button 2.
84
02_NewOrleansMP58_gb.indd 84
07.12.2007 14:57:27 Uhr
Notes:
• This setting can be performed only
if no CD changer is connected to the
device and if the device is not in AUX
mode.
• As long as the rear AUX input is
switched on, it can be selected with
the SRC button 2, even if no external audio source is connected.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "AUX MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
"AUX ON" or "AUX OFF" appears on the display.
쏅 Press the or button 4 to toggle
between "AUX ON" and "AUX OFF".
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Adjusting the level of the external audio
source
The volume at which an external audio
source is played can differ from the volume
of the device-specific audio sources (radio,
CD, MP3/WMA). To compensate for this
difference, you can adjust the level of the
external audio sources.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "AUX MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "AUX LEVEL" appears.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 to adjust
the level between 0 and 8.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
ENGLISH
External audio sources
Naming the external audio source
For the rear AUX input, you can enter a separate name that is shown on the display if
you select the connected audio source.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly until "AUX MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "AUX NAME EDIT" appears.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 to enter
the character at the current position.
쏅 Press the or button 4 to change
to a different position.
쏅 Press the MENU•OK button 5 to
store the name.
When you have finished making your changes,
쏅 press the ESCAPE button ;.
85
02_NewOrleansMP58_gb.indd 85
07.12.2007 14:57:27 Uhr
External audio sources
Mixing an external audio source with
another audio source (MIX AUX)
You can play back an external audio source
together with any other audio source at
the same time. The simultaneous playback
must be activated in the menu.
With the "MIXAUXON" setting, the audio
source connected via the rear AUX input is
played back together with the currently selected audio source (e.g. radio or CD). With
the "MIXAUXOFF" setting, only the currently
selected audio source is played back.
쏅 Press the MENU•OK button 5.
The display shows "MENU".
쏅 Press the or button 4 repeatedly
until "VARIOUS MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly until "MIXAUXON" or "MIXAUXOFF"
appears.
쏅 Press the or button 4 to toggle
between "MIXAUXON" and "MIXAUXOFF".
When you have finished making your changes,
쏅 press the ESCAPE button ;.
Bluetooth
For wireless hands-free calling, you can
connect a Bluetooth cell phone to the device via the Blaupunkt Bluetooth/USB interface. Hence, you can control the most
important functions of the Bluetooth cell
phone from the device (e.g. making and
ending calls as well as answering or rejecting calls). Furthermore, you can use the
cell phone as additional audio source via
Bluetooth streaming (if the cell phone supports this function).
If you want to connect a Bluetooth cell
phone via the Bluetooth/USB interface to
the device and use it, you can perform the
necessary settings in the "BLUETOOTH"
submenu in the menu of the device. As long
as no Bluetooth/USB interface is connected
to the device, the "BLUETOOTH" submenu
is without function.
Explanations about the functions of this
menu can be found in the operating instructions of the Bluetooth/USB interface.
86
02_NewOrleansMP58_gb.indd 86
07.12.2007 14:57:28 Uhr
Restoring factory settings
You can restore the original factory settings
of the device.
쏅 Press the MENU•OK button 5.
쏅 Press the or button 4 repeatedly
until "VARIOUS MENU" appears on the
display.
button 4 to open the
쏅 Press the
menu.
쏅 Press the or button 4 repeatedly
until "NORMSET" appears.
button 4 to open the
쏅 Press the
menu.
쏅 Press the button 4 repeatedly until "NORMSET ON" appears on the display.
The device switches off and immediately
on again. All settings are returned to the
factory settings.
Note:
If you do not press and hold the button 4 long enough, "NORMSET OFF"
appears on the display. In this case,
your individual settings remain intact
and the device remains switched on.
You can exit the menu with the ESCAPE
button ;.
Factory settings:
Volume of traffic
announcements
(TA VOLUME)
30
Power-on volume
(On Volume)
20
Volume of muting
(MUTE LEVEL)
0
Volume of telephone/
navigation announcement (TEL VOLUME)
25
Seek tuning sensitivity
(SENSITIVITY)
HI6
Scan time (SCAN TIME)
10
Programme type (PTY)
OFF
PTY language
(PTY LANGUAGE)
ENGLISH
Time display (CLOCK)
OFF
Time (CLOCK SET)
0:00
Time display mode
(CLOCK MODE)
24HR
Confirmation beep
(BEEP)
ON
Mode of rear AUX input
(CDC)
OFF
External audio source
(AUX)
OFF
Regional function (REG)
OFF
Display brightness
DIM DAY 15,
DIM NIGHT
12
RDS
ON
ENGLISH
Restoring factory settings
(NORMSET)
87
02_NewOrleansMP58_gb.indd 87
07.12.2007 14:57:28 Uhr
Technical data
Technical data
Amplifier
Output power:
4 x 18 watts sine at
14.4 V and
1% distortion factor
at 4 ohms.
4 x 26 watts sine
in accordance with
DIN 45324 at
14.4 V at 4 ohms.
4 x 50 watts
max. power
Tuner
Wavebands (Europe):
FM :
87.5 - 108 MHz
MW :
531 - 1 602 kHz
LW :
153 - 279 kHz
FM frequency response:
35 - 16,000 Hz
CD
Frequency response:
20 - 20,000 Hz
Pre-amp out
4 channels:
3V
Input sensitivity
AUX input:
Tel./Navi input:
2 V / 6 kΩ
10 V / 1 kΩ
Weight
approx. 1.36 kg
Subject to changes
88
02_NewOrleansMP58_gb.indd 88
07.12.2007 14:57:28 Uhr
Einbauanleitung • Installation instructions • Notice de montage • Istruzioni di installazione •
Inbowhandleiding • Monteringsanvisning • Instrucciones de instalación • Instruções de montagem • Monteringsvejledning • Instrukcja montażowa • Návod k montáži • Montážny návod •
Инструкция по установке
Einbauanleitung
Sicherheitshinweise
Für die Dauer der Montage und
des Anschlusses beachten Sie bitte folgende Sicherheitshinweise.
• Minuspol der Batterie abklemmen!
Dabei die Sicherheitshinweise des
Kfz- Herstellers beachten.
• Beim Bohren von Löchern darauf
achten, dass keine Fahrzeugteile beschädigt werden.
• Der Querschnitt des Plus- und Minuskabels darf 1,5 mm2 nicht unterschreiten.
• Fahrzeugseitige Stecker nicht an
das Radio anschließen!
Die für Ihren Fahrzeugtyp erforderlichen Adapterkabel erhalten Sie im
BLAUPUNKT-Fachhandel.
• Je nach Bauart kann Ihr Fahrzeug
von dieser Beschreibung abweichen. Für Schäden durch Einbauoder Anschlussfehler und für Folgeschäden übernehmen wir keine
Haftung.
Sollten die hier aufgeführten Hinweise für Ihren Einbau nicht passen, so wenden Sie sich bitte an
Ihren Blaupunkt-Fachhändler, Ihren
Fahrzeughersteller oder unsere
Telefon-Hotline.
Bei Einbau eines Amplifier oder
Changers müssen unbedingt erst die
Gerätemassen angeschlossen werden,
bevor die Stecker für die Line-In- oder
Line-Out-Buchse kontaktiert werden.
Fremdgerätemassen dürfen nicht an
der Autoradiomasse (Gehäuse) angeschlossen werden.
Installation instructions
Safety instructions
When carrying out installation
work and making connections please
observe the following safety instructions:
• Disconnect the negative terminal of
the battery! When doing so, please
observe the vehicle manufacturer’s
safety instructions.
• Make sure you do not damage vehicle components when drilling any
holes.
• The cross sections of the positive
and negative cables must not be less
than 1.5 mm2.
• Do not connect the vehicle’s plug
connectors to the radio!
You can obtain the adapter cable required for your vehicle type from any
BLAUPUNKT dealer.
• Depending on the model, your vehicle may differ from the description
provided here. We accept no responsibility for any damages due to incorrect installation or connection or for
any consequential damages.
563
14_EA_NewOrleansMP58.indd 563
07.12.2007 15:23:00 Uhr
If the information provided here is
not suitable for your specific installation requirements, please contact
your Blaupunkt dealer, your vehicle
manufacturer or our telephone hotline.
When installing an amplifier or changer,
you must first connect the device earth
connections before connecting the
plugs for the line-in or line-out jacks.
Earth connection of external devices
may not be connected to earth of car
sound system (housing).
Notice de montage
Consignes de sécurité
Respecter les consignes de sécurité suivantes pendant la durée du
montage et du branchement.
• Débrancher le pôle (-) de la batterie !
Respecter les consignes de sécurité
du constructeur automobile !
• Veiller à n’endommager aucune pièce du véhicule en perçant des trous.
• La section du câble (+) et (-) ne doit
pas dépasser 1,5 mm2.
• Ne pas brancher les connecteurs
du véhicule sur la radio !
Les câbles d’adaptation nécessaires pour le type de véhicule sont
disponibles auprès des revendeurs
BLAUPUNKT.
• En fonction du modèle, votre véhicule peut différer de cette description. Nous déclinerons toute responsabilité en cas de dommages causés
par des erreurs de montage ou de
connexion et en cas de dommages
consécutifs.
Si les indications décrites ici ne s’appliquent au montage que vous voulez
effectuer, adressez-vous à votre revendeur Blaupunkt, votre constructeur automobile ou notre service
d’assistance téléphonique.
Pour le montage d’un amplificateur ou
changeur, les masses d’appareil doivent être d’abord connectées avant de
connecter les fiches pour les connecteurs Line In ou Line Out.
Les masses des appareils externes ne
doivent pas être raccordées à la masse de l'autoradio (boîtier).
Istruzioni di
installazione
Note di sicurezza
Durante il montaggio e l’allacciamento osservate per favore le seguenti
istruzioni sulla sicurezza.
• Staccate il polo negativo della batteria! Nel fare ciò osservate le istruzioni
di sicurezza del fabbricante d’auto.
• Quando praticate dei fori, fate attenzione a non danneggiare nessuna
parte dell’autovettura.
• La sezione dei cavi positivi e negativi non deve essere mai inferiore
a 1,5 mm2.
• Non collegate alla radio le spine
in dotazione di autovettura!
Richiedete ad un negoziante specializzato in articoli BLAUPUNKT il cavo
564
14_EA_NewOrleansMP58.indd 564
07.12.2007 15:23:01 Uhr
di adattamento richiesto per il vostro
modello di autovettura.
• A seconda del modello il Suo veicolo
può differire da questa descrizione.
Non forniamo garanzia per danni
derivanti da errori di montaggio o
di collegamento e per danni conseguenti.
Se le indicazioni qui elencate non
sono adatte al Suo montaggio, La preghiamo di rivolgersi al Suo rivenditore Blaupunkt, al fabbricante dell’auto
o alla nostra hotline telefonica.
Quando vengono montati un amplificatore o un multilettore CD, bisogna
innanzi tutto allacciare le masse degli
apparecchi prima di eseguire la connessione delle spine con le prese line-in e
line-out.
Le masse di altri apparecchi non devono essere collegate alla massa dell'autoradio (involucro).
Inbowhandleiding
Adviezen voor de
veiligheid
Wilt u dedurende het monteren en aansluiten de volgende veiligheidsadviezen
in acht nemen.
• De minpool van de batterij afklemmen! De veiligheidsadviezen van de
fabrikant in acht nemen.
• Bij het gaten boren erop letten dat
geen voertuigonderdelen worden
beschadigd.
• De dwarsdoorsnede van de plusen minkabel mag niet minder dan
1,5 mm2 zijn.
• Stekker aan de voertuigkant niet
aan de radio aansluiten!
De voor uw voertuig vereiste adapterkabel is bij de BLAUPUNKT-vakhandel verkrijgbaar!
• Afhankelijk van de uitvoering kan uw
auto afwijken van deze beschrijving.
Voor schade door fouten in montage
of aansluiting en schade als gevolg
daarvan aanvaarden wij geen aansprakelijkheid.
Mochten de hier vermelde aanwijzingen voor de montage voor u niet van
toepassing zijn, dan kunt u contact
opnemen met uw Blaupunkt-vakhandel, uw autofabrikant of onze telefoon-hotline.
Bij inbouw van een versterker of cd-wisselaar moeten eerst de massacontacten
van de apparaten worden verbonden
voordat de stekkers voor de line-in- of
line-out-bussen worden aangesloten.
De massa van andere apparaten mag
niet aan de massa van de autoradio
(huis) worden aangesloten.
Monteringsanvisning
Skyddsanvisningar
Vänligen beakta följande skyddsanvisningar under pågående montage
och anslutning.
• Lossa polskon från batteriets minuspol! Följ därvid fordonstillverkarens
skyddsanvisningar.
565
14_EA_NewOrleansMP58.indd 565
07.12.2007 15:23:01 Uhr
• Se till att inga av fordonets komponenter skadas i samband med borrning av hål.
• Plus- och minuskabelns ledningsarea måste vara minst 1,5 mm2.
• Fordonets stickkontakt får inte
anslutas till radion!
Din BLAUPUNKT fackhandel tillhandahåller för resp fordonstyp erforderlig adapterkabel.
• Beroende på konstruktionstyp kan
fordonet avvika från denna beskrivning. Vi frånsäger oss allt ansvar för
skada eller följdskada pga. felaktig
montering eller anslutning.
Om här givna monteringsanvisningar ej stämmer överens med faktiska
förhållanden, vänligen kontakta
Blaupunkt fackhandel, representant
för fordonets tillverkare eller vår telefonkundtjänst.
Vid montering av förstärkare eller cdväxlare måste först apparatstommen
jordas, innan stickpropparna ansluts till
in- eller utgångarna (hylstag line-in resp
line-out).
Jord från andra apparater får inte
anslutas till bilradions jord (höljet).
Instrucciones de
instalación
Normas de seguridad
Durante el montaje y la conexión
es imprescindible observar las siguientes normas de seguridad.
• Desemborne el polo negativo de la
batería. Observe las normas de seguridad dadas por el fabricante del
vehículo.
• Al perforar agujeros, asegúrese de
no dañar ninguna pieza del vehículo.
• La sección transversal del cable positivo y del cable negativo no debe
ser menor de 1,5 mm2.
• ¡No conecte a la radio los conectores ubicados en el vehículo!
Los cables adaptadores necesarios
para su vehículo los encontrará en el
comercio especializado en artículos
de la marca BLAUPUNKT.
• Dependiendo del modelo, es posible
que su vehículo varíe un poco con
respecto a la descripción aquí dada.
Tenga en cuenta que no asumimos
ninguna responsabilidad por los daños debidos a un montaje o conexión
incorrectos ni por los daños resultantes.
Si las instrucciones aquí dadas no
son aptas para el montaje en su vehículo, póngase en contacto con su
proveedor de artículos Blaupunkt o
con el fabricante del vehículo, o llame a nuestro teléfono de atención al
cliente.
En caso de montar un amplificador o un
cambiadiscos, es necesario conectar la
puesta a tierra de las unidades antes de
establecer el contacto de los conectores
para las hembrillas Line-In y Line-Out.
No deben conectarse masas de otros
equipos a la masa de la radio (carcasa).
566
14_EA_NewOrleansMP58.indd 566
07.12.2007 15:23:01 Uhr
Instruções de
montagem
Instruçõesdesegurança
Durante a montagem e a ligação
do aparelho, queira respeitar as seguintes instruções de segurança.
• Separar o pólo negativo da bateria!
Respeitar ao mesmo tempo as instruções de segurança do fabricante
do automóvel.
• Quando se procede à furagem de
buracos, prestar atenção para não
serem danificadas quaisquer partes
do veículo.
• As secções transversais dos cabos
positivo e negativo não devem ser
inferiores a 1,5 mm2.
• Não ligar as fichas existentes do
lado do automóvel ao auto-rádio!
Os cabos adaptadores necessários
para o seu automóvel podem ser
adquiridos nos revendedores da
BLAUPUNKT.
• O seu veículo pode divergir desta
descrição em função do modelo.
Não assumimos qualquer responsabilidade por erros de montagem ou
de ligação nem por danos daí decorrentes.
Caso as presentes instruções não sejam adequadas para a montagem no
seu veículo, dirija-se ao revendedor
da Blaupunkt, ao fabricante do seu
veículo ou à nossa linha verde.
No caso de montagem de um amplificador ou leitor multi-CD, é imprescindível
ligar primeiro os aparelhos à terra antes
de se conectar as fichas às tomadas Line
In ou Line Out.
A massa de aparelhos externos não
deve ser ligada à massa do auto-rádio
(caixa).
Monteringsvejledning
Sikkerhedshenvisninger
Under monteringen og tilslutningen skal følgende sikkerhedshenvisninger iagttages.
• Batteriets negative pol skal afbrydes! Herved skal bilfabrikantens sikkerhedshenvisninger iagttages.
• Vær opmærksom på, at ingen bildele
ødelægges under boringen af huller.
• Tværsnittet af plus- og minuskablet
må ikke underskride 1,5 mm2.
• Bilens stik må ikke tilsluttes radioen!
De nødvendige adapterkabler til din
biltype kan købes hos BLAUPUNKTspecialforretningen.
• Alt efter konstruktion kan bilen afvige fra denne beskrivelse. For skader
på grund af monterings- eller tilslutningsfejl og for følgeskader overtager vi intet ansvar.
Hvis de her anførte henvisninger
til monteringen ikke skulle passe,
kontakt din Blaupunkt-specialforretning, bilfabrikanten eller vor telefonhotline.
Ved montering af en forstærker eller et
Multi CD-apparat skal apparaternes stel
567
14_EA_NewOrleansMP58.indd 567
07.12.2007 15:23:02 Uhr
først tilsluttes, før stikkene for tilslutningerne Line-In eller Line-Out sættes i.
Eksterne enheders stelforbindelse
må ikke sluttes til bilradioens stelforbindelse (kabinet).
Instrukcja montażowa
Wskazówki bezpieczeństwa
Podczas montażu i podłączania należy
przestrzegać poniższych wskazówek
bezpieczeństwa.
• Odłączyć biegun ujemny akumulatora! Przestrzegać wskazówek bezpieczeństwa producenta pojazdu.
• Przy wierceniu otworów uważać, aby
nie uszkodzić któregoś z urządzeń
pokładowych pojazdu.
• Przekrój kabla plusowego i minusowego nie może być mniejszy niż
1,5 mm2.
• Nie podłączać wtyczek samochodu do radia!
Odpowiedni dla danego typu pojazdu przewód-adapter można nabyć
u autoryzowanego sprzedawcy produktów BLAUPUNKT.
• Zależnie od marki i modelu, konstrukcja Państwa pojazdu może niekiedy
odbiegać od podanego tu opisu. Firma
Blaupunkt wyklucza wszelką odpowiedzialność za szkody spowodowane
błędnym montażem i instalacją urządzenia.
W przypadku, gdy podane tu wskazówki nie znajdują zastosowania w
Państwa pojeździe, prosimy skon-
taktować się z autoryzowanym sprzedawcą produktów Blaupunkt, producentem pojazdu lub zadzwonić do
naszej infolinii.
Przy montażu wzmacniacza lub zmieniarki należy koniecznie najpierw podłączyć masy urządzeń, zanim połączona
zostanie wtyczka do gniazda Line-In lub
Line-Out.
Do masy radioodtwarzacza (obudowa) nie wolno podłączać masy obcych
urządzeń.
Návod k montáži
Bezpečnostní pokyny
Během montáže a připojení
dodržujte prosím následující bezpečnostní pokyny.
• Odpojte záporný pól akumulátoru! Přitom dodržujte bezpečnostní
pokyny výrobce vozidla.
• Při vrtání otvorů dbejte na to, abyste
nepoškodili žádné díly vozidla.
• Průřez kabelu plus a minus pólu
musí být minimálně 1,5 mm2.
• Konektory od vozidla nepřipojujte
k rádiu!
Adaptérový kabel potřebný pro vaše
vozidlo obdržíte ve specializované
prodejně BLAUPUNKT.
• V závislosti na konstrukci se může
postup u vašeho vozidla od zde
popsaného postupu lišit. Za škody
způsobené montáží nebo připojením
nepřebíráme žádné ručení.
568
14_EA_NewOrleansMP58.indd 568
07.12.2007 15:23:02 Uhr
Pokud zde uvedené pokyny pro
montáž neodpovídají vašemu vozidla, obraťte se na specializovaného
prodejce Blaupunkt, výrobce vozidla
nebo naši horkou linku.
Při montáži zesilovače nebo měničů,
předtím než budou konektory zapojeny
do zdířek Line-in nebo Line-out, musí
být nejprve bezpodmínečně připojeny
kostry přístrojů.
Kostry jiných přístrojů nesmí být připojeny na kostru autorádia (kryt přístroje).
Montážny návod
borným pripojením nepreberáme
záruku.
Ak by tu uvedené pokyny na montáž
nezodpovedali vášmu vozidlu, obráťte sa prosím na špecializovaného
predajcu fy Blaupunkt, výrobcu vášho vozidla alebo na našu zákaznícku
linku.
Pri montáži zosilňovača alebo meniča
je bezpodmienečne nutné najprv zapojiť kostru prístroja, než sa nakontaktujú
zástrčky do zásuvky Line-In alebo LineOut.
Kostry cudzích prístrojov sa nesmú
napojiť na kostru (schránku) autorádia.
Bezpečnostné pokyny
Počas montáže a zapojenia rešpektujte následné bezpečnostné pokyny.
• Odpojte záporný pól akumulátora!
Rešpektujte pri tom bezpečnostné
pokyny výrobcu vozidla.
• Pri vŕtaní otvorov dávajte pozor na
to, aby sa nepoškodili žiadne diely
vozidla.
• Prierez kábla kladného a záporného
pólu nesmie byť menší ako 1,5 mm2.
• Koncovky elektroinštalácie vozidla sa do rádia nesmú zapojiť!
Potrebný kábel s adaptérom pre vaše
vozidlo obdržíte v špecializovaných
predajniach BLAUPUNKT.
• V závislosti od konštrukcie sa môže
postup pri vašom vozidle od tu popísaného postupu líšiť. Za škody
spôsobené montážou alebo neod-
Инструкция по
установке
Указания по технике
безопасности
Во время монтажа и подсоединения
соблюдайте, пожалуйста, следующие
указания по технике безопасности.
• Отсоедините минусовую клемму
аккумулятора! Соблюдайте при
этом правила техники безопасности завода-изготовителя Вашего автомобиля.
• При сверлении отверстий следите
за тем, чтобы не повредить компоненты автомобиля.
• Сечение плюсового/минусового
кабелей должен быть не меньше
1,5 мм2.
569
14_EA_NewOrleansMP58.indd 569
07.12.2007 15:23:02 Uhr
• Не включайте в аудиосистему автомобильные штекеры!
Необходимые для Вашего типа автомобиля адаптерные кабели Вы можете приобрести в авторизованном
сервисном центре Blaupunkt.
• Ваш автомобиль может - в зависимости от конструкции - отклоняться
от данного описания. Завод-изготовитель аудиосистемы не несет
ответственности за повреждения
и-за ошибок при монтаже или подключении, а также за косвенный
ущерб.
Если перечисленные здесь указания для Ваших условий монтажа не
подходят, то обратитесь, пожалуйста, в авторизованный сервисный
центр Blaupunkt или продавцу
Вашего автомобиля.
При установке усилителя или чейнджера перед соединением штекеров
гнезд линейного входа и выхода сначала нужно в обязательном порядке
подключить массы устройств.
Запрещается подключение масс
посторонних устройств к массе аудиосистемы (корпусу).
570
14_EA_NewOrleansMP58.indd 570
07.12.2007 15:23:02 Uhr
Mitgelieferte Montage- und
Anschlussteile
Supplied Mounting Hardware
Materiel de montage fourni
Componenti di fissaggio comprese
nella fornitura
Meegeleverde montagematerialen
Medföljande monteringsdetaljer
Ferretería de montaje suministrada
Elementos de fixação fornecidos
Medleverede monterings- og
tilslutningsdele
Dołączone części montażowe i
połączeniowe
Přiložené montážní díly a přípojné
svorky
Dodávané montážne a pripojovacie
dielce
Поставляемые в комплекте
компоненты для установки и
подсоединения
Als Sonderzubehör erhältlich
Available as an optional accessory
Disponible en option
Reperibili come accessori extra
Als speciale accessoire verkrijgbaar
Tillval
De venta como accesorios especiales
Disponíveis como acessórios
opcionais
Fås som specialtilbehør
Dostępne jako wyposażenie
dodatkowe
Jako zvláštní příslušenství můžete
obdržet
Ako osobitné príslušenstvo
dostanete
Поставляется как дополнительная
принадлежность
Preamp./Sub./Center - out cable
A
B
A
7 607 001 512
7 607 621 . . .
571
14_EA_NewOrleansMP58.indd 571
07.12.2007 15:23:02 Uhr
Einbausätze
Installation kits
Kits de montage
Set di montaggio
Inbouwsets
Monteringssatser
Juegos de montaje
Kits de montagem
Indbygningssæt
Zestawy montażowe
Montážní soupravy
Montážne súpravy
Установочные комплекты
1.
12V
2.
ca. 10 mm
7 608 . . . . . .
3.
0°- 30°
+/– 10°
+/– 10°
572
14_EA_NewOrleansMP58.indd 572
07.12.2007 15:23:02 Uhr
4.
6. Ausbau / Removal / Démontage /
Smontaggio / Demontage /
Urmontering / Desmontaje /
Desmontagem / Udbygning /
Demontaż / Demontáž / Demontáž /
Демонтаж
USB connection
antenna connection
1.
USB cable
5.
182
2.
165
53
2.
B
1-20
8 613 150 002
A
3.
7.
12V
573
14_EA_NewOrleansMP58.indd 573
07.12.2007 15:23:03 Uhr
8.
C-1
10
C-3
Aut. antenna
*
13 16 19
9 12
8 11
15 18
14 17 20
C
6
3
4
3
5
7
2
4
6
8
1
3
5
7
2
4
6
8
B
10 Ampere
A
A
B
1
2
3
4
5
6
7
Gala
Radio Mute
Sub-Out
Permanent +12V
Aut. antenna *
Illumination
Kl.15/Ignition
1
2
3
4
5
6
7
Speaker out RR+
Speaker out RR–
Speaker out RF+
Speaker out RF–
Speaker out LF+
Speaker out LF–
Speaker out LR+
8
Masse/GND
8
Speaker out LR–
1
2
3
4
5
Line Out LR
Line Out RR
Line Out / Ground
Line Out LF
Line Out RF
SW Supply +12V
Amp. *
C1
6
FB +12V / RC +12V
+12V Amplifier
Summe
Sum
Somme
Somma
Som
Summa
Suma
Soma
Celkem
Súčet
Сумма
8
5
1
5
6
3
2
1
D
C-2
7 10
4
2
7
9
1
C2
150 mA
C3
7
8
9
10
11
Telefon NF in +
Telefon NF in –
Radio Mute
SW Supply - RC +12V *
Remote Control
13
14
15
16
17
CDC-Data In
CDC-Data Out
Permanent +12V
SW Supply +12V *
Bus - Masse/GND
12
RC - GND
18
CDC/AUX1 Audio IN-GND
19
CDC/AUX1 Audio IN-L
20
CDC/AUX1 Audio IN-R
CD-Changer / AUX IN
Amplifier
Optional
(Remote Control Eye)
574
14_EA_NewOrleansMP58.indd 574
09.07.2008 15:03:52 Uhr
9.
Preamp./Sub./Center - out cable
7 607 001 512
Relais
+12V Amplifier
A
+12V
7
1 35
Kl. 15 +12V
8
24 6
Sub Out
Radio Mute
LR
F LF
RR R
+
+
+
+
-
4 Ohm
4 Ohm
4 Ohm
4 Ohm
+12V
12V
Änderungen vorbehalten!
Subject to changes!
Sous réserve de modifications!
Modifiche riservate!
Wijzigingen voorbehouden!
Ändringar förbehålles!
Modificaciones reservadas!
Sob reserva de alterações!
Ret til ændringer forbeholdes!
Zmiany techniczne zastrzeżone!
Změny vyhrazeny!
Zmeny vyhradené!
Завод-изготовитель оставляет за собой право на внесение изменений!
575
14_EA_NewOrleansMP58.indd 575
07.12.2007 15:23:03 Uhr
© 2007 All rights reserved by Blaupunkt. This material may be reproduced, copied or distributed for personal
use only.
This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology
outside of this product is prohibited without a license from Microsoft.
576
14_EA_NewOrleansMP58.indd 576
07.12.2007 15:23:03 Uhr
Bitte den ausgefüllten Gerätepass sicher aufbewahren!
Please keep the filled-in radio pass in a safe place!
Prière de conserver soigneusement la carte d’autoradio remplie !
Tenete per favore il libretto di apparecchio, debitamente riempito, in un
posto sicuro!
Bewaar de ingevulde apparaatpas op een veilige plaats!
Vänligen förvara ifyllt apparatpass på säker plats!
¡Favor guardar el documento del aparato debidamente llenado en un lugar
seguro!
Por favor, guardar o cartão preenchido do aparelho num lugar seguro!
Det udfyldte apparatpas opbevares et sikkert sted!
Prosimy przechowywać metrykę radia w bezpiecznym miejscu!
Vyplněný dokument o přístroji prosím bezpečně uschovejte!
Vyplnený dokument o prístroji prosím bezpečne uschovajte!
Пожалуйста, храните заполненный паспорт устройства в надежном месте!
577
14_EA_NewOrleansMP58.indd 577
07.12.2007 15:23:03 Uhr
Germany
Austria
Belgium
Denmark
Finland
France
Great Britain
Greece
Ireland
Italy
Luxembourg
Netherlands
Norway
Portugal
Spain
Sweden
Switzerland
Czech. Rep.
Hungary
Poland
Turkey
USA
Brasil
(Mercosur)
Malaysia
(Asia Pacific)
Phone:
Fax:
(D)
(A)
(B)
(DK)
(FIN)
(F)
(GB)
(GR)
(IRL)
(I)
(L)
(NL)
(N)
(P)
(E)
(S)
(CH)
(CZ)
(H)
(PL)
(TR)
(USA)
0180-5000225
01-610 39 0
02-525 5444
44 898 360
09-435 991
01-4010 7007
01-89583 8880
210 94 27 337
01-46 66 700
02-369 62331
40 4078
00 31 24 35 91 338
+47 64 87 89 60
2185 00144
902 52 77 70
08-7501850
01-8471644
02-6130 0446
76 889 704
0800-118922
0212-335 07 23
800-950-2528
05121-49 4002
http://www.blaupunkt.com
01-610 39 391
02-525 5263
44-898 644
09-435 99236
01-4010 7320
01-89583 8394
210 94 12 711
01-46 66 706
02-369 62464
40 2085
00 31 24 35 91 336
+47 64 87 89 02
2185 00165
91 410 4078
08-7501810
01-8471650
02-6130 0514
–
022-8771260
0212-346 00 40
708-6817188
(BR)
0800 7045446
+55-19 3745 2773
(MAL) +604-6382 474
WWW:
+604-6413 640
07/08 - CM-AS/SCS1 (dt, gb, fr, it, nl, sw, es, pt, dk, pl, cz, sk, ru)
Country:
Name:
New Orleans MP58
.....................................................................
Typ:
7....................................................................
648 009 310
Serien-Nr:
BP ................................................................
8622405681
Gerätepass
Blaupunkt GmbH, Robert-Bosch-Straße 200, D-31139 Hildesheim
578
14_EA_NewOrleansMP58.indd 578
09.07.2008 16:35:37 Uhr