User's Manual
Rev: 1.0, December 2010
Website: http://www.jwele.com
Mini-ITX Motherboard
MINIXTM 7025-UC3
Disclaimer
The intellectual property of this manual belongs to our company. The ownership of all of the
products, including accessories and software etc. belong to our company. No one is permitted to
copy, change, or translate without our written permission.
We compiled this manual based on our careful attitude, but we can not guarantee the accuracy of
the contents. This manual is purely technical documentation, without any hint or other meanings,
and we won't commit users' misunderstanding of the typesetting error.
Our products are in continuous improvement and updating, Therefore, we retain the right that we
won't give notice to the users in future.
Copyright
All of the trademark in this manual belong to their own registered company.
All of the products name is only for identification, its title belongs to its manufacturer or brand
owner.
Table of Contents
Chapter 1 Introduction............................................................................................. 4
1.1
1.2
1.3
1.4
Package Checklist.................................................................................................................4
Specifications.......................................................................................................................5
Mainboard Layout.................................................................................................................6
Connecting Rear Panel I/O Devices........................................................................................7
Chapter 2 Hardware Setup........................................................................................ 8
2.1 Choosing a Computer Chassis................................................................................................8
2.2 Installing Mainboard.............................................................................................................8
2.3 Installing CPU and CPU Cooler...............................................................................................9
2.4 Installation of Memory Modules........................................................................................... 10
2.5 Connecting Peripheral Devices............................................................................................. 11
2.5.1 Serial ATA Connectors................................................................................................... 11
2.5.2 PCIE slot...................................................................................................................... 11
Chapter 3 Jumpers & Headers Setup........................................................................12
Chapter 4 BIOS Setup Utility....................................................................................17
4.1 About BIOS Setup............................................................................................................... 17
4.2 To Run BIOS Setup............................................................................................................. 17
4.3 About CMOS....................................................................................................................... 17
4.4 The POST (Power On Self Test)........................................................................................... 17
4.5 BIOS Setup — CMOS Setup Utility........................................................................................ 18
4.5.1 CMOS Setup Utility........................................................................................................ 18
4.5.2 Control Keys................................................................................................................. 19
4.5.3 Main Menu................................................................................................................... 20
4.5.4 Advanced Setting.......................................................................................................... 22
4.5.5 Boot Setting................................................................................................................. 29
4.5.6 Security Setting............................................................................................................ 31
4.5.7 Power Setting............................................................................................................... 32
4.5.8 JUSTw00T!................................................................................................................... 35
4.5.9 Exit Setting.................................................................................................................. 39
Chapter 5 Driver Installation....................................................................................42
MINIX 7025-UC3
User's Manual
Chapter 1 Introduction
1.1 Package Checklist
Thank you for choosing our product.
Please check the following packing and accessories, if there is any broken or part missing,
please contact with your franchiser.
•
•
•
•
•
Rear I/O Panel X 1
User's Manual X 1
Driver/Utility CD X 1
Serial ATA Signal Cable X 2
Serial ATA Power Cable X 2
The items listed above are for reference only, and are subject to change without notice.
--
MINIX 7025-UC3
User's Manual
1.2 Specifications
CPU
Main Chipset
- Support AMD(R) Socket AM3 processors
- AMD Phenom™ II x4/ Phenom™ II x3/ Phenom™ II x2/ Athlon™ II x4/
Athlon™II x3/Athlon™ II x2/ Sempron™ 1xx processors
- Integrated GeForce® 7025 & nForce® 630a MCP
Support 2x1.5V DDR3 DIMM socket supporting up to 8GB of system memory
Support for DDR3 1066/1333/1600(OC)MHz memory modules
AMI BIOS, supports Plug&Play
BIOS
Supports Advanced Power Management ACPI,STR
CPU temperature, Fan speed, System Voltage monitoring
1 x PS/2 Keyboard port
1 x PS/2 Mouse port
1 x VGA port
1 x COM port
Rear Panel I/O
1 x RJ45 port
4 x USB 2.0 ports
- 3 x Audio jacks (Line In / Line Out / MIC In)
- 1 x 20-pin ATX main power connector
- 1 x 4-pin ATX 12V power connector
- 4 x SATA 3Gb/s connectors
- 2 x System fan headers
Internal I/O
- 1 x CPU FAN header
- 1 x Front panel header
Connectors
- 1 x Front panel audio header
- 1 x SPDIF_OUT header
- 1 x SPEAK header
- 2 x USB 2.0 headers for additional 4 USB 2.0 ports (by cables)
- Onboard 6-channel HD Audio Codec
Sound
- Front Panel Jumper, provides stereo MIC port on front panel
Onboard LAN
- Onboard 10/100/1000Mbps compatible LAN (Optional)
Expansion Slots - 1 x PCIE slot
Form Factor
Mini ITX (170mm*170mm)
Main Memory
-
--
MINIX 7025-UC3
User's Manual
1.3 Mainboard Layout
JC61D3ITX01 V1 . 0
170 * 170
CFAN
PS 2
COM1
SFAN1
FUSB2
JLPC
FUSB1
3
VGA
FPANEL
PWR12V
USB
B T1
SFAN2
USB _ LAN1
SPEAK
AUDIO
F _ AUDIO
JSPDIF
SATA2
SATA1
SATA4
SATA3
JBAT
PCIE1
(This picture is only for reference)
--
MINIX 7025-UC3
User's Manual
1.4 Connecting Rear Panel I/O Devices
The rear I/O part of these mainboard provides the following I/O ports:
PS 2 Mouse
PS 2 Keyboard
(This picture is only for reference)
• PS/2 Mouse: Connects to a PS/2 mouse.
• PS/2 Keyboard: Connects to a PS/2 keyboard.
• VGA: Connects to a monitor's VGA input.
• COM: Connect to external modem.mouse or other devices that support this communication
portocol.
• USB: The USB ports are used to connect USB 2.0/1.1 devices such as scanner, speakers,
keyboard, mouse, hub, digital camera, joystick, etc.
• LAN: The LAN port allows the motherboard to connect to a local area network by means of
a network hub.
• AUDIO(Rear Panel Audio):
Line-in (Light Blue): This jack is used to connect to the line out from any external audio
sources such as MP3 player, CD player, AM/FM radio tuner, etc.
Line-out (Front Left/Right Jack, Lime): This jack is used to connect to the front left and
right channel speakers of the audio system.
Mic-in (Pink): This jack is used to connect an external microphone.
--
MINIX 7025-UC3
User's Manual
Chapter 2 Hardware Setup
2.1 Choosing a Computer Chassis
• Choose a chassis big enough to install this mainboard.
• As some features for this mainboard are implemented by cabling connectors on the mainboard
to indicators and switches or buttons on the chassis, make sure your chassis supports all the
features required.
• If there is possibility of adopting some more hard drives, make sure your chassis has sufficient
power and space for them.
• Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O shield
of the chassis matches the I/O port configuration of this mainboard. You can find an I/O shield
specifically designed for this mainboard in its package.
2.2 Installing Mainboard
Most computer chassis have a base with many mounting holes to allow the mainboard to be
securely attached, and at the same time, prevent
the system from short circuits. There are two ways
to attach the mainboard to the chassis base:
(1)with studs, or (2) with spacers.
Basically, the best way to attach the board is with
studs. Only if you are unable to do this should you
attach the board with spacers. Line up the holes on
the board with the mounting holes on the chassis.
If the holes line up and there are screw holes, you
can attach the board with studs. If the holes line
up and there are only slots, you can only attach with
spacers. Take the tip of the spacers and insert them into the slots. After doing this to all the slots,
you can slide the board into position aligned with slots. After the board has been positioned,
check to make sure everything is OK before putting the chassis back on.
To install this mainboard:
1. Locate all the screw holes on the mainboard and the chassis base.
2. Place all the studs or spacers needed on the chassis base and have them tightened.
3. Face the mainboard’s I/O ports toward the chassis’s rear panel.
4. Line up all the mainboard’s screw holes with those studs or spacers on the chassis.
5. Install the mainboard with screws and have them tightened.
--
MINIX 7025-UC3
User's Manual
2.3 Installation of the CPU and CPU Cooler
Before installing the CPU, please comply with the following conditions:
1. Please make sure that the mainboard supports the CPU.
2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong
direction, the CPU will not insert properly. If this occurs, please change the insert direction of
the CPU.
3. Please add an even layer of heat sink paste between the CPU and CPU cooler.
4. Please make sure the CPU cooler is installed on the CPU prior to system use, otherwise
overheating and permanent damage of the CPU may occur.
5. Please set the CPU host frequency in accordance with the processor specifications. It is not
recommended that the system bus frequency be set beyond hardware specifications since it
does not meet the required standards for the peripherals. If you wish to set the frequency
beyond the proper specifications, please do so according to your hardware specifications
including the CPU, graphics card, memory, hard drive, etc.
2.3.1 Installation of the CPU
1. Unlock the socket by pressing the
o
lever sideways, then lift it up to a 90 .
2. Position the CPU above the socket such that
the CPU corner with the gold triangle matches
the socket corner with a small triangle.
3. Carefully insert the CPU into the socket until it
fits place.
Figure 2
Figure 1
4. When the CPU is in
place, push down the
socket lever to secure
the CPU.
The lever clicks on the
side tab to indicate that
it is locked.
Figure 3
--
MINIX 7025-UC3
User's Manual
2.3.2 Installation of the CPU Cooler
For proper installation, please kindly refer to the instruction manuals of your CPU Cooler.
2.4 Installation of Memory Modules
This mainboard provides two 1.5v DDR3 DIMM slots, which supports dual channel memory
technology. To activate the dual channel configuration, you need to install two identical
(same brand, speed, size and chip-type) memory modules into these DIMM slots. Otherwise
the memory will only operate at single channel mode.
For dual channel DDR3 installation:
Populate two DDR3 DIMM modules of the same type and size into slots [DIMM1] + [DIMM2].
Static electricity can damage the electronic components of the computer or optional boards.
Before starting these procedures, ensure that you are discharged of static electricity by
touching a grounded metal object briefly.
To install system memory:
1. Power off the computer and unplug the
AC power cord before installing or
removing memory modules.
2. Locate the DIMM slot on the board.
3. Hold two edges of the DIMM module
carefully, keep away from touching its
connectors.
4. Align the notch key on the module with
the rib on the slot.
5. Firmly press the module into the slots until the ejector tabs at both sides of the slot
automatically snap into the mounting notch. Do not force the DIMM module in with extra
force as the DIMM module only fits in one direction.
6. To remove the DIMM modules, push the two ejector tabs on the slot outward
simultaneously, and then pull out the DIMM module.
- 10 -
MINIX 7025-UC3
User's Manual
2.5 Connecting Peripheral Devices
2.5.1 Serial ATA Connectors
Each SATA connector serves as one single channel to connect one SATA device by SATA cable.
JC61D3ITX01 V1 . 0
170 * 170
CFAN
PS 2
COM1
SFAN1
FUSB2
JLPC
FUSB1
3
VGA
FPANEL
PWR12V
USB
B T1
SFAN2
USB _ LAN1
SPEAK
F _ AUDIO
JSPDIF
SATA2
SATA1
AUDIO
SATA4
SATA3
JBAT
PCIE1
2.5.2 PCIE slot
Install PCIE card into slot “PCIE1” .
- 11 -
MINIX 7025-UC3
User's Manual
Chapter 3 Jumpers & Headers Setup
Quick Components Guide
11
JC61D3ITX01 V1 . 0
170 * 170
CFAN
PS 2
10
COM1
SFAN1
9
8
FUSB2
VGA
FPANEL
PWR12V
FUSB1
3
7
JLPC
12
USB
B T1
6
SFAN2
USB _ LAN1
SPEAK
SATA2
SATA1
SATA4
SATA3
JSPDIF
AUDIO
JBAT
F _ AUDIO
PCIE1
NO.
1
2
3
4
5
6
7
1 23
Layout
F_AUDIO
SFAN2
JSPDIF
JBAT
SPEAK
ATXPWR
FUSB1/FUSB2
4
Page NO.
No.
13
13
1
1
1
1
1
8
9
10
11
12
- 12 -
5
Layout
FPANEL
SFAN1
CFAN
PWR12V
JLPC
Page NO.
1
13
1
1
1
MINIX 7025-UC3
User's Manual
Checking Jumper Settings
• For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the
jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position.
• For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in.
How to identify the PIN1 jumpers?
Please check the mainboard carefully, the PIN1 is marked by "1" or white thick line.
1-F_AUDIO(Front Panel Audio Connection Header)
Pin No.
Header
1
2
3
4
5
6
7
8
9
10
PORT1L
AGND
PORT1R
PRESENCE#
PORT2R
SENSE1_RETURN
SENSE_SEND
No Pin
PORT2L
SENSE2_RETURN
HD Audio Definition
Microphone_Left
Ground
Microphone_Right
-ACZ_DET
Line2_Right
AuD_R_Return
FAUDIO_JD
N/A
Line2_Left
AuD_L_Return
AC97 Audio Definition
Microphone
Ground
MIC Power
N/A
Line out (R)
N/A
N/A
N/A
Line Out(L)
N/A
2/9-SFAN1/SFAN2(Fan Power Connectors Header)
SFAN1:System fan connectors
Pin No.
1
Definition
GND
2
+12V
3
RPM
These fan connectors are not jumpers.
DO NOT place jumper caps on these
connectors.
- 13 -
1 2
10 9
F _ AUDIO
MINIX 7025-UC3
User's Manual
GND
3-S/PDIF Output Connection Header
S/PDIF (Sony/Philips Digital Interface) is a standard audio transfer file format.
It is usually found on digital audio equipment such as a DAT (Digital Audio
Tape) machine or audio processing device. It allows the transfer of audio from
one file to another without the conversion to and from an analog format, which
could degrade the signal quality.
1
GND
OUT
OUT
NC
VCC
VCC
4-JBAT(CMOS Memory Clearing Header)
The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b)
you forgot the supervisor or user password preset in the BIOS menu, (c) you are unable to
boot-up the system because the CPU ratio/clock was incorrectly set in the BIOS menu, or (d)
whenever there is modification on the CPU or memory modules.
This header uses a jumper cap to clear the CMOS
memory and have it reconfigured to the default values
stored in BIOS.
• Pins 1 and 2 shorted (Default): Normal operation.
• Pins 2 and 3 shorted: Clear CMOS memory.
5/8-SPEAK/FPANEL(Speaker Headers & Front Panel Switches)
- 14 -
RST
+HD _ LED-
+
PWR _ LED
-
PWR _ ON
HD_LED (Red): Hard Driver LED connector
SPEAK:
This connector connects to the case-mounted
HD LED cable, and the LED will light when the
Pin No.
Definition
hard drive(s) is/are being accessed.
1
SPK +
2
NC
RST (Blue): Reset Switch
3
NC
This connector connects to the case-mounted
4
SPK reset switch which allows you to reboot without
having to power-off the system and thus prolonging the life of the power supply or system.
PWR_ON (Black): Power Switch
Depending on the setting in the BIOS setup, this switch serves two functions which will allow
you to power-on/off the system or to enter the suspend mode.
PWR_LED (Green): Power/Standby LED
When the system's power is on, this LED will light. When the system is in the S1 (POS - Power
on Suspend) or S3 (STR - Suspend to RAM, optional) state, it will blink every second.
SPEAKER (Yellow or Black): Speaker Connector
This 4-pin connector connects to the case-mounted speaker.
MINIX 7025-UC3
User's Manual
6/11- ATX Power Input Connectors
ATXPWR (ATX Power) connector
We recommend to use our motherboard with a power supply that complies with the ATX12V
Power Supply Design Guide Version 1.1. Every ATX12V power supply unit has a standard
24-pin ATX main power connector that must be plugged into this connector. If you would like
to use an old power supply with only a 20-pin ATX main power connector, then please plug
the 20-pin ATX main power connector along with pin 1 and pin 13.
PWR12V (+12V Power) connector
Your power supply unit may come with a 4-pin or 8-pin +12V power connector. The +12V
power enables the delivery of more +12VDC current to the CPU's Voltage Regulator Module
(VRM). Please connect the 4-pin power
to this connector.
10 20
+12V
+5VSB
PWRGD
GND
+5V
GND
+5V
GND
+ 3 . 3V
+ 3 . 3V
+5V
+5V
N/ C
GND
GND
GND
PS - ON
GND
-12V
+ 3 . 3V
3
+12V
GND
4
1 2
+12V
GND
PWR12V
1 13
ATXPWR
7-FUSB1/FUSB2(Additional USB Port Headers)
Pin No.
Definition
Pin No.
Definition
1
3
VCC
Data 0-
2
4
VCC
Data 1-
5
Data 0+
6
Data 1+
7
Ground
8
10
Ground
NC
- 15 -
MINIX 7025-UC3
User's Manual
10-CFAN(CPU Fan Power Connectors Header)
CFAN:CPU fan connectors
Pin No.
1
2
3
4
Definition
GND
+12V
RPM
Control
These fan connectors are not jumpers.
DO NOT place jumper caps on these
connectors.
12-JLPC
This set of headers are reserved for internal debug purpose.
- 16 -
MINIX 7025-UC3
User's Manual
Chapter 4 BIOS Setup Utility
BIOS stands for Basic Input and Output System. It was once called ROM BIOS when it was stored
in a Read-Only Memory (ROM) chip. Now manufacturers would like to store BIOS in EEPROM which
means Electrically Erasable Programmable Memory. BIOS used in this series of mainboard is stored
in EEPROM, and is the first program to run when you turn on your computer.
BIOS performs the following functions:
1. Initializing and testing hardware in your computer (a process called "POST", for Power On Self
Test).
2. Loading and running your operating system.
3. Helping your operating system and application programs manage your PC hardware by means of
a set of routines called BIOS Run-Time Service.
4.1 About BIOS Setup
BIOS Setup is an interactive BIOS program that you need to run when:
1. Changing the hardware of your system. (For example: installing a new Hard Disk etc.)
2. Modifying the behavior of your computer. (For example: changing the system time or date, or
turning special features on or off etc.)
3. Enhancing your computer's behavior. (For example: speeding up performance by turning on
shadowing or cache)
4.2 To Run BIOS Setup
First access BIOS setup menu by pressing <F1> key after “POST” is complete (before OS is
loaded). After the first BIOS be setupped(or loaded default values) and save, the <DEL> key will
be pressed if you will enter BIOS setup menu.
4.3 About CMOS
CMOS is the memory maintained by a battery. CMOS is used to store the BIOS settings you have
selected in BIOS Setup. CMOS also maintains the internal clock. Every time you turn on your
computer, the BIOS Looks into CMOS for the settings you have selected and configures your
computer accordingly. If the battery runs out of power, the CMOS data will be lost and POST will
issue a “CMOS invalid” or “CMOS checksum invalid” message. If this happens, you have to replace
the battery and check and configure the BIOS Setup for the new start.
4.4 The POST (Power On Self Test)
POST is an acronym for Power On Self Test. This program will test all things the BIOS does
- 17 -
MINIX 7025-UC3
User's Manual
before the operating system is started. Each of POST routines is assigned a POST code, a unique
number which is sent to I/O port 080h before the routine is executed.
4.5 BIOS Setup — CMOS Setup Utility
• In order to increase system stability and performance, our engineering staff is constantly
improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual
are for your reference only, and may not completely match with what you see on your screen.
• Do not change the BIOS parameters unless you fully understand its function.
4.5.1 CMOS Setup Utility
After powering up the system, the BIOS message appears on the screen,when the first time or
when CMOS setting wrong, there is following message appears on the screen , but if the first
first BIOS be setuped(or loaded default values) and save, the <DEL> key will be pressed if you
will enter BIOS setup menu.
Press F1 to Run SETUP
If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt>+
<Del> keys, or by pressing the reset button on computer chassis. Only when these two methods
should be fail that you restart the system by powering it off and then back on.
After pressing <F1> or <Del> key, the main menu appears.
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power
JUSTW00t!
Exit
► System Information
System Time
System Date
Power On Beep
►
►
►
►
SATA
SATA
SATA
SATA
Port
Port
Port
Port
1
2
3
4
► CPU TDP Verify
[20:50:32]
[Tue 09/03/2009]
[Enabled]
←↓
[ST380215AS]
↑
[Not Detected] Enter
[Not Detected] F1
[Not Detected] F10
ESC
[Disabled]
:
:
:
:
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 18 -
MINIX 7025-UC3
User's Manual
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration.
Advanced
For changing the advanced system settings.
Boot
For changing the system boot configuration.
Security
For changing the system security setttings.
Power
For changing the advanced power management(APM) configuration.
Exit
For selecting the exit options and loading default settings.
4.5.2 Control Keys
Press F1 to pop up a small help window that describes the appropriate keys to use and the
possible selections for the highlighted item.
Please check the following table for the function description of each control key.
Control Key(s)
Function Description
← →
Move cursor left or right to select Screens
Move cursor up or down to select items
To Change option for the selected items
To bring up the selected screen
Main Menu - Quit and not save changes into CMOS Status Page
Setup Menu and Option Page Setup Menu - Exit current page and
return to Main Menu
General help
Change Colors
Discard Changes
Load Failsafe Defaults
Load Optimal Defaults
Save configuration changes and exit setup
/
↑/↓
+/ <Enter>
<ESC>
<F1>
<F2/F3>
<F7>
<F8>
<F9>
<F10>
- 19 -
MINIX 7025-UC3
User's Manual
4.5.3 Main Menu
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power
JUSTW00t!
Exit
► System Information
System Time
System Date
Power On Beep
►
►
►
►
SATA
SATA
SATA
SATA
Port
Port
Port
Port
1
2
3
4
► CPU TDP Verify
[20:50:32]
[Tue 09/03/2009]
[Enabled]
←↓
[ST380215AS]
↑
[Not Detected] Enter
[Not Detected] F1
[Not Detected] F10
ESC
[Disabled]
:
:
:
:
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
► System Information
Please Enter this submenu, this will be display BIOS verison, build date, ID number, also will
display CPU type, Speed, count, and Memory Size and so on.
BIOS SETUP UTILITY
Main
System Overview
AMIBIOS
Version
:08.00.15
Build Date:07/19/10
ID
:C61130F0
Processor
AMD Athlon(tm)II X2 240 Processor
Speed
:2800MHz
Count
:2
System Memory
Size
:2008MB
←
↑
↓
F1
F10
ESC
Select Screen
Select Item
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 20 -
MINIX 7025-UC3
User's Manual
• System time
This item sets the time you specify(usually the current time)in the format of [Hour],[Minute]and
[Second].
• System date
This item sets the date you specify(usually the current date in the format of [Month],[Date],and
[Year].
• Power on Beep
A beep on post.Options: Disabled,Enabled.
► SATA Port 1/2/3/4
This item sets the status of auto detection of SATA/IDE devices while enterting setup, and BIOS
will auto detects the presence of SATA/IDE devices. Press "Enter" Key to enter the submenu.
BIOS SETUP UTILITY
Main
SATA Port1
Disabled: Disables LBA
Mode.
Auto: Enables LBA
Mode if the device
supports it and the
device is not already
formatted with LBA
Mode disabled.
Device
:Hard Disk
Vendor
:ST380215AS
Size
:80.0GB
LBA Mode :Supported
Block Mode:16Sectors
PIO Mode :4
Async DMA :MultiWord DMA-2
Ultra DMA :Ultra DMA-6
S.M.A.R.T.:Supported
LBA/Large Mode
Block (Multi-Sector Transfer)
PIO Mode
DMA Mode
S.M.A.R.T
32Bit Data Transfer
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
←
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
• LBA/Large Mode
Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the device supports
this mode, and if the device was not previously formatted with LBA mode disabled.
• Block (Multi-Sector Transfer)
Enables or disables data multi-sectors transfers. When set to [Auto] , the data transfer from and
to the device occurs multiple sectors at a time if the device supports multi-sector transfer frature.
When set to [Disabled] , the data transfer from and to the device occurs one sector at a time.
- 21 -
MINIX 7025-UC3
User's Manual
• PIO Mode
Allows you to select the data transfer mode.
• DMA Mode
Selects the DMA mode.
• S.M.A.R.T
Set the Smart Monitoring, Analysis, and Reporting Technology.
• 32Bit Data Transfer
Enables or disables 32-bit data transfer.
• Back to Main Setup Menu
• CPU TDP Verify
Options: Disabled,Enabled.
4.5.4 Advanced Setting
BIOS SETUP UTILITY
Main
Advanced
Boot
Security
Advanced Settings
►
►
►
►
Power
JUSTW00t!
Exit
Configure CPU.
Select Screen
←
↑
↓
Select Item
Enter Go to Sub Screen
F1
General Help
F10
Save and Exit
ESC
Exit
CPU Configuration
Chipset
Onboard Device
PCIPnP
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
This submenu including these configurations, such as CPU, Northbridge, Southbridge, Onboard
Device, only CPU Configuration submenu dispay diallog box as follwoing.
► CPU Configuration
Click <Enter> key to enter its submenu, it will be display configureted CPU information,
including Module Version, Manufacturer , CPU type, Frequency, FSB Speed, Cache L1 , Cache
L2 and so on.
- 22 -
MINIX 7025-UC3
User's Manual
BIOS SETUP UTILITY
Advanced
CPU Configuration
Moudule Version: 14.16
AGESA Version: 3.7.0.0
Physical Count : 1
Logical Count : 2
AMD Athlon(tm) II X2 240 Processor
Revision: C2
Cache L1: 384KB
Cache L2: 1536KB
Speed
: 2727MHz,
NB Clk: 1800MHz
Able to Change Freq. : Yes
uCode Patch Level
: 0x1000083
GART Error Reporting
Microcode Update
Secure Virtual Machine Mode
Cool 'N 'Quiet
ACPI SRAT Table
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
This option should
remain disabled for
the normal operation.
The driver developer
may enable it for
testing purpose.
←
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
• GART Error Reporting
This option should remain disabled for the normal operation.The Driver developer may enable it
for testing purpose.
• Microcode Update.
Options:Disabled,Enabled.
• Secure Virtual Machine Mode
Enable/Disable Secure Virtual Machine Mode(SVM).
• Cool'n'Quiet
Enable/disable the generation of ACPI_PPC,_PSS,and_PCI objects.
• ACPI SRAT Table
Enable or Disable the building of ACPI SRAT Table.
• Turbo Core
Disable/Enable Turbo core funcion of 6 cores cpu. Options:Disabled,Enabled.
• Back to Advanced Setup Menu
- 23 -
MINIX 7025-UC3
► Chipset Configuration
Click <Enter> key to enter its submenu, it will be display chipset configuration.
User's Manual
BIOS SETUP UTILITY
Advanced
Advanced Chipset Setting
WARNING: Setting wrong values in below sections
may cause system to malfunction.
NUMM ROM Version: 4.082.10
Primary Graphics Adapter
OnChip and PCIe VGA selection
iGPU Frame Buffer Detect
OnChip VGA Frame Buffer Size
Options
PCI Express->PCI->
IGP->PCI->PCI
Express
[PCI Express->PCI]
[Disable Onchip]
[Auto]
[32MB]
IDE Configuration
Serial-ATA 0
[Enable]
Hard Disk Write Protect
[Disable]
IDE Detect Time Out(Sec)
[35]
ATA(PI) 80Pin Cable Detection [Host]
RAID Setup
nVidia RAID Function
[Disabled]
←↑↓
Select Screen
Select Item
Enter Go to Sub
Screen
F1
General Help
F10
Save and Exit
ESC
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
• Primary Graphics Adapter
Options:PCI Express ->PCI->IGP,IGP->PCI->PCI Express
• OnChip and PCIe VGA selection
Select OnChip or PCIe VGA to diaplay
• iGPU Frame Buffer Detect
iGPU Frame Buffer Size Auto Detect
- 24 -
MINIX 7025-UC3
User's Manual
• OnChip VGA Frame Buffer Size
iGPU Frame Buffer size.
• Onboard IDE Controller
Allows BIOS to Enable or Disable IDE Controller
• Serial-ATA 0
Options:Enabled,Disabled.
• Hard disk write protect
Disable/enable device write protection.this will be effictive only if device is accessed through
BIOS.
• IDE Detect Time Out
Select the time out value for detecting ATA/ATAPI device(s)
• ATA(PI) 80Pin Cable Detection
Select the mechanism for detecting 88pin ATA(PI) Cable.
• nVidia RAID Function
Options:Enabled,Disabled.
• Back to Advanced Setup Menu
► Onboard Device
Click <Enter> key to enter its submenu.
BIOS SETUP UTILITY
Advanced
Onboard Devices Setting
► USB Device
AZALIAIDE AUDIO
Lan Controller
Saming/BootROM control
Serial Port1 Address
Configure the USB support.
[Disabled]
[35]
[Host & Device]
[3F8/IRQ4]
←
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 25 -
MINIX 7025-UC3
User's Manual
► USB Device
The items in this menu allows you to change the USB-related features.
BIOS SETUP UTILITY
Main
USB Configuration
Module Version -2.24.3-13.4
USB Devices Enabled :
None
Legacy USB Support
USB 2.0 Controller Mode
BIOS EHCI Hand-Off
USB1 1.1 Controller
USB1 2.0 Controller
[Enabled]
[HiSpeed]
[Enabled]
[Enabled]
[Enabled]
Enables support for
legacy USB. AUTO
option disables
legacy support if
no USB devices are
connected.
←↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
• Legacy USB Support
Enabled or Disabled Legacy USB option, and Auto option disables legacy support if no USB
devices are connected.
• USB 2.0 Controller Mode
Allow you to selects the HiSpeed(480Mbps) or FullSpeed(12Mbps).
• BIOS EHCI Hand-Off
This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change
should claim by EHCI driver.
・Press <Esc> key to return to "Onboard Device Configuration" menu.
• AZALIA AUDIO
Options:Auto,Disabled
• Lan Controller
Options:Auto,Disabled
• Saming/BootRom Control
MAC LAN rom boot Set
• Serial Port1 Address
Allows BIOS to Select Serial Port1 base Addresses.
- 26 -
MINIX 7025-UC3
► PCIPnP
Click <Enter> key to enter its submenu.
User's Manual
BIOS SETUP UTILITY
Advanced
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Clear NVRAM
Plug & Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster
OffBoard PCI/ISA IDE Card
[No]
[No]
[64]
[Yes]
[Disabled]
[Enabled]
[Auto]
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ11
IRQ14
IRQ15
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
DMA
DMA
DMA
DMA
DMA
DMA
Channel
Channel
Channel
Channel
Channel
Channel
0
1
3
5
6
7
Reserved Memory Size
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
Clear NVRAM during
System Boot.
←
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
[Disabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 27 -
MINIX 7025-UC3
User's Manual
• Clear NVRAM
This item for clearing NVRAM during system boot.
Optional:Yes,No
• Plug & Play O/S
This item lets the BIOS configure all the devices in the system or lets the operating system
configure plug and play (PnP) devices not required for boot if your system has a Plug and Play
operating system.
Optional:Yes,No
• PCI Latency Timer
This item sets value in units of PCI clocks for PCI device latency timer register.
Optional:32,64,96,128,160,192,224,248
• Allocate IRQ to PCI VGA
This item assigns IRQ to PCI VGA card if card requests IRQ or doesn't assign IRQ to PCI VGA
card even if card requests an IRQ.
Optional:Yes,No
• Palette Snooping
This item informs the PCI devices that an ISA graphics device is installed in the system so the
card will function correctly.
Optional:Disabled,Enabled
• PCI IDE BusMaster
This item uses PCI busmastering for BIOS reading / writing to IDE derives.
Optional:Disabled,Enabled
• OffBoard PCI/ISA IDE Card
This item works for most PCI IDE cards, some PCI IDE cards may require this to be set to the
PCI slot number that is holding the card.
Optional:Auto,PCI Slot1~6
• Reserved Memory Size
Size of memory block to reserve for legacy ISA devices.
• Engineer mode
Engineer mode control.
- 28 -
MINIX 7025-UC3
User's Manual
4.5.5 Boot Setting
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power PC&Health
Boot Settings
Exit
Configure Settings
during System Boot.
► Boot Settings Configuration
←
► Boot Device Priority
► Hard Disk Drives
► Removable Drives
↑
↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
► Boot Settings Configuration
Click <Enter> key to enter its submenu.
BIOS SETUP UTILITY
Boot
Boot Settings Configuration
Quick Boot
Full Screen Logo
Bootup Num-Lock
Halt On
Wait For 'F1' If Error
Hit 'Del' Message Display
Interrupt 19 Capture
[Enabled]
[Disabled]
[On]
[No Errors]
[Enabled]
[Enabled]
[Enabled]
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
←
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
• Quick Boot
This item allows you to speed up Power On Self Test (POST) after you power on the computer. If
this is set to [Enabled], BIOS will shorten or skip some check items during POST.
• Full screen Logo
This allows you to enable or disable the full screen logo display feature.
• Bootup Num-Lock
Allows you to select the power-on state for the NumLock.
- 29 -
MINIX 7025-UC3
User's Manual
• Halt On
Options:All Errors,No Errors,All But Keyboard.
• Wait For 'F1' If Error
When set to Enabled,the system waits for the F1 key t be pressed when error occurs.
• Hit 'Del' Message Display
When set to Enabled,the system displays the message "Press DEL to run Setup" durning POST.
• Interrupt 19 Capture
When set to Enabled, this function allows the option ROMs to trap Interrupt 19.
• Back to Boot Setup Menu
► Boot Device Priority
Click <Enter> key to enter submenu, it will be display specifies the boot sequence from the
available devices.
► Hard Disk Drives
Click <Enter> key to enter submenu, it will be display specifies the boot device priority sequence
from available hard disk drives.
► Removable Drives
Click <Enter> key to enter submenu, it will be display specifies the boot device priority sequence
from available removable drives.
- 30 -
MINIX 7025-UC3
User's Manual
4.5.6 Security Setting
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power PC&Health
Security Settings
Supervisor Password : Not Installed
User Password
: Not Installed
Change Supervisor Password
User Access Level
Change User Password
Clear User Password
Password Check
Boot Sector Virus Protection
Flash Write Protection
Exit
Install or Change the
password.
←
[Full Access]
[Setup]
↑
↓
Enter
F1
F10
ESC
Select Screen
Select Item
Change
General Help
Save and Exit
Exit
[Disabled]
[Enabled]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
This item allows you to Chage Supervisor/User Password, Type the password, up to eight
characters, and press <Enter>. The password typed now will clear any previously entered
password from CMOS memory. You will be asked toconfirm the password. Type the password
again and press <Enter>.
Note: Don’t forget your password. If you forget the password, you will have to open the
computer case and clear all information in the CMOS before you can start up the system.
But by doing this, you will have to reset all previously set options.
• Boot Sector Virus Protection
Enabled/Disable Boot Sector Virus Protection
• Flash Write Protection
Options:Enabled,Disabled.
- 31 -
MINIX 7025-UC3
User's Manual
4.5.7 Power Setting
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power
Power Settings
JUSTw00T!
Exit
Section for Advanced
ACPI Configuration.
► ACPI Configuration
► APM Configuration
► PC Health
←↑↓
Select Screen
Select Item
Enter Go to Sub Screen
F1
General Help
F10
Save and Exit
ESC
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
► ACPI Configuration
Click <Enter> key to enter its submenu.
BIOS SETUP UTILITY
Power
ACPI Configuration
ACPI Aware O/S
Suspend mode
ACPI Version Festures
ACPI APCI support
[Yes]
[S1 (POS)]
[ACPI V1.0]
[Enabled]
Select the ACPI
state used for
System Suspend.
←
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 32 -
MINIX 7025-UC3
User's Manual
• ACPI Aware O/S
Enable/Disable ACPI support for Operating system
• Suspend Mode
Allows you to select the Advanced Configuration and Power Interface (ACPI) state to be used
for system suspend.
・ACPI Version Features
Enable RSDP pointers to 64-bit Fixed system Description tables
• ACPI APCI support
Include ACPI APCI table Pointer to RADT pointer list.
・Press <Esc> key to return to "Power" menu.
► APM Configuration
Click <Enter> key to enter its submenu, APM Configuration Template Manager allows
you to manage Power Managerment default or custom configuration templates.
BIOS SETUP UTILITY
Power
APM Configuration
EuP Function
Power Button Mode
[Disabled]
[On/Off]
EuP Function,Super IO
power SAVING function.
Disabled
Enabled
APM Resume Event Confoguration
Resume On PME#
Resume On PCIE Wake#
Resume On USB
Resume By RTC Alarm
Resume By PS2 Mouse
Resume By PS2 Keyboard
Restore on AC Power Loss
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Power Off]
←
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 33 -
MINIX 7025-UC3
User's Manual
► PC Health
Click <Enter> key to enter its submenu, it will be display hardware health configuration,
including System temperature, CPU temperature, FAN speed and all kinds of voltages.
BIOS SETUP UTILITY
Power
PC Health
H/W Health Function
[Enabled]
System Temperature
CPU Temperature
:23oC/73oF
:29oC/84oF
Fan configuration
mode setting
CPUFAN Speed
SYSFAN1 Speed
CPU Voltage
CPU HT Voltage
Dram Voltage
+5V Voltage
+12V Voltage
VCC
VBAT
CPUFAN Mode Setting
Manual Duty Cycle Setting
←
:1.384 V
:1.193 V
:1.542 V
:4.992 V
:12.104 V
:3.248 V
:2.960 V
[Manual Mode
[100]
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
• CPUFAN Mode Setting
Available options: Manual Mode,Thermal Cruise Mode,Speed Cruise Mode
• Manual Duty Cycle Setting
Set Fan at fixed Duty-Cycle Min=0 Max=100 Please input Dec number;
- 34 -
MINIX 7025-UC3
User's Manual
4.5.8 JUSTw00t! Setting(OverClock Settings)
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power
OverClock Settings
► AMD Overclocking Configuration
► DRAM Timing ConFiguration
► Memory Configuration
Memory 2T Mode
[2T Mode]
Memory CLK
CAS Latency(Tcl)
RAS/CAS Delay(Trcd)
Row Precharge Time(Trp)
Min Active RAS(Tras)
RAS/RAS Delay(trrd)
Row Cycle (Trc)
Write Recover Time(Twr)
CPU/LTD Spread Spectrum
PCIE Spread Spectrum
SATA Spread Spectrum
JUSTw00T!
Exit
ConFigur CPU
frequency and
voltage
:N/A,667MHZ
:N/A,9 CLK
:N/A,9 CLK
:N/A,9 CLK
:N/A,24 CLK
:N/A,4 CLK
:N/A,33 CLK
:N/A,6 CLK
[200.0]
[Enabled]
[Enabled]
GPU Over control
[Auto]
CPU Frequency,MHZ
[200.0]
MCP PCI-Express Frequency,MHZ [100]
←
Select Screen
Select Item
Enter Go to Sub Screen
F1
General Help
F10
Save and Exit
ESC
Exit
↑
↓
CPU Voltage Control
[Auto]
CPU Voltage
:1.264v
K10 CPUNB Voltage Control
[Auto]
DRAM Voltage Control
[Auto]
DRAM Voltage
:1.936 v
Chipset Voltage Control
[Auto]
Chip Voltage
:1.272v
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 35 -
MINIX 7025-UC3
► AMD Overclocking Configuration
Click <Enter> key to enter its submenu.
User's Manual
BIOS SETUP UTILITY
JUSTw00T!
AMD Overclocking Configuration
Speed:2727MHZ,
NB Clk:2000MHZ
Maximum FSB Multiplier :13.5x
Processor Frequency Multiplier
Processor Voltage
Processor NB Frequency(NBFID)
Processor NB Voltage(NBVID)
SB to K8(CPU) Freq Auto
SB to K8(CPU) LinkWidth
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[16 ↓ 16↑]
Configure CPU
frequency and
voltage
←
Select Screen
Select Item
Enter Go to Sub Screen
F1
General Help
F10
Save and Exit
ESC
Exit
↑
↓
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
• Processor Frequency Multiplier
options:Auto,X4.0 800 MHZ,X4.5 900MHZ,X5.0 1000MHZ,X5.5 1100MHZ,X6.0 1200MHZ,X6.5
1300MHZ, X7.0 1400MHZ ,X7.5 1500MHZ
• Processor Voltage
Options:Auto,1.425V,1.412V,1.400V,1.387V,1.375V,1.362V,1.350V,1.337V
• Processor NB Frequency (NBFID)
Options:Auto,X4 800MHZ,X5 1000MHZ,X6 1200MHZ,X7 1400MHZ,X8 1600MHZ,X9 1800MHZ,
X10 2000MHZ,X11 2200MHZ.
• Processor NB Voltage(NBVID)
Options:Auto,1.425V,1.412V,1.400V,1.387V,1.375V,1.362V,1.350V,1.337V
• SB to K8(CPU) Freq Auto
SB to K8(CPU) frequency selection by CPU capability.
• SB to K8(CPU)LinkWidth
SB to K8(CPU) LinkWidth selection
- 36 -
MINIX 7025-UC3
User's Manual
・Press <Esc> key to return to "JUSTw00T!" menu.
► DRAM Timing Configuration
BIOS SETUP UTILITY
JUSTw00T!
DRAM Timing Configuration
Options
Memory Clock Mode
DRAM Timing Mode
[Auto]
[Auto]
Memory 2T Mode
[2T Mode]
Auto
Limit
Manual
←
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
• Memory Clock Mode
This item is to select the memory clock mode.
• DRAM Timing Mode
This item is to select the DRAM Timing mode.
• Memory 2T Mode
Options:Auto, 1T Mode,2T Mode.
・Press <Esc> key to return to "JUSTw00T!" menu.
- 37 -
MINIX 7025-UC3
► Memory Configuration
Click <Enter> key to enter its submenu.
User's Manual
BIOS SETUP UTILITY
JUSTw00T!
Memory Configuration
Bank Interleavin
Channel Inter leaving
Enable Clock to All DIMMs
MemClk Tristate C3/ATLVID
Memory Hole Remapping
DCT Unganged Mode
Power Down Enable
Page Smashing
[Auto]
[Auto]
[Disabled]
[Disabled]
[Enabled]
[Always]
[Enabled]
[Disabled]
Enable Bank Memory
Interleaving
←
↑
↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
• Bank Interleaving
Sets the bank interleaving feature.
• Channel Interleaving
Enable Channel Memory Interleaving.
• Enable Clock to All DIMMs
This item is to enable or disable the unused clocks to DIMMs even the memory slots are not
populated.
• MemClk Tristate C3/ATLVID
Enables or disables the MemClk Tri-Stating during C3 and Alt VID.
• Memory Hole Remapping
Enables or disables the memory remapping around the memory hole.
• DCT Unganged Mode
This item allows the selection of the unganged DRAM mode (64-bit width).
• Power Down Enable
This item is to enable or disable the DDR power down mode.
• Page Smashing
S/W Control of Page Smashing Mechanism.
- 38 -
MINIX 7025-UC3
User's Manual
4.5.9 Exit Setting
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power
Exit Options
JUSTw00t!
Exit
Exit system setup
after saving the
changes.
Save Changes and Exit
Discard Changes and Exit
Discard Changes
←
Select Screen
Select Item
Enter Go to Sub Screen
F1
General Help
F10
Save and Exit
ESC
Exit
↑
↓
Load Optimal Defaults
Load Failsafe Defaults
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Highlight this item and select <Ok>,then press <Enter> to save the changes that you have
made in the Setup Utility and exit the Setup Utility. Or press <Cancel> to return to the main
menu.
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power
Exit Options
JUSTw00t!
Exit
Exit system setup
after saving the
changes.
Save Changes and Exit
Discard Changes and Exit
Discard Changes
F10 key can be used
for this operation.
Load Optimal Defaults
Load Failsafe Defaults
Save configuration changes and exit ←setup?Select Screen
↑
↓
Select Item
Enter Go to Sub Screen
F1
General Help
[Ok]
[Cancel] F10
Save and Exit
ESC
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 39 -
MINIX 7025-UC3
User's Manual
Highlight this item and select <Ok>,then press <Enter> to discard any changes that you have
made in the Setup Utility and exit the Setup Utility. Or press <Cancel> to return to the main
menu.
Main
Advanced
BIOS SETUP UTILITY
Security
Power
Boot
Exit Options
JUSTw00t!
Exit
Exit system setup
without saving any
changes.
Save Changes and Exit
Discard Changes and Exit
Discard Changes
ESC key can be used
for this operation.
Load Optimal Defaults
Load Failsafe Defaults
←
Discard changes and exit setup?
↑
↓
Enter
F1
[Ok]
[Cancel] F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Sleect <Ok>and press <Enter> to discard changes and exit, or press <Cancel> to return to the
main menu.
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power
JUSTw00t!
Exit Options
Save Changes and Exit
Discard Changes and Exit
Discard Changes
Load Optimal Defaults
Load Failsafe Defaults
Exit
Discards changes
done so far to any of
the setup questions.
Discard changes?
[Ok] [Cancel]
←
Select Screen
Select Item
Enter Go to Sub Screen
F1
General Help
F10
Save and Exit
ESC
Exit
↑
↓
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 40 -
MINIX 7025-UC3
User's Manual
This option opens a dialog box that let you install optimized defaults for all appropriate items in
the Setup Utility. Select <OK> and then <Enter> to install the defaults. select <Cancel> and
then <Enter> to not install the defaults. The optimized defaults place demand on the system
that may be greater than the performance level of the components, such as the CPU and the
memory. You can cause fatal errors or instability if you install the optimized defaults when your
hardware does not support them. If you only want to install setup defaults for a specific option,
select and display that option, and then press <F9>.
BIOS SETUP UTILITY
Main
Advanced
Boot
Security Power JUSTw00t! Exit
Exit Options
Save Changes and Exit
Discard Changes and Exit
Discard Changes
Load Optimal Defaults
Load Failsafe Defaults
Load Optimal Default
values for all the
setup questions.
Load Optimal Defaults?
F9 key can be used
for this operation.
[Ok] [Cancel]
This option opens a dialog box that lets you install fail-safe defaults for all appropriate items in
the Setup Utility: Select <Ok> and the <Enter> to install the defaults. Select <Canel> and then
<Enter> to not install the defaults. The fail-safe defaults place no great demand on the system
and are generally stable. If your system is not functioning correctly, try installing the fail-safe
defaults as a first step in getting your system working properly again.If you only want to install
fail-safe defaults for a specific option, select and display that option, and then press <F8>.
Main
Advanced
Boot
BIOS SETUP UTILITY
Security
Power
JUSTw00t!
Exit Options
Save Changes and Exit
Discard Changes and Exit
Discard Changes
Load Failsafe Defaults?
Load Optimal Defaults
Load Failsafe Defaults
[Ok]
Exit
Load Failsafe Default
values for all the
setup questions.
F8 key can be used
for this operation.
[Cancel]
v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
- 41 -
MINIX 7025-UC3
User's Manual
Chapter 5 Driver Installation
Check your package and there is Driver CD included. This CD consists of all drivers you need. In
addition, this CD also include an auto detect software which can tell you which hardware is installed,
and which drivers needed so that your system can function properly.
Insert CD into your CD-ROM drive and the menu should appear as below. If the menu does not
appear, double-click My Computer / double-click CD-ROM drive or click Start / click Run / type X:\
Setup.EXE (assuming X is your CD-ROM drive).
+ Mainboard Driver Installation Utility
+ Userful Software Utility
> Browse CD
Exit
(This picture is only for reference)
From the Main MENU you may make 4 selections:
1. +Mainboard Driver Installation Utility: Click to enter the driver installation menu.
2. +Useful Software Utility: Click to enter the utilities installation menu.
3. >Browse CD: Click to browse the contents of this “Driver & Utility CD”.
4. Exit: Click to exit this installation menu.
- 42 -
MINIX 7025-UC3
User's Manual
When you choose Mainboard Driver installation Utility, the drivers menu should appear as
below:
Back <-
nForce Chipset Installation Utility
Nvidia VGA Graphics Driver
Onboard LAN Driver
Realtek HD Audio Driver
Exit
(This picture is only for reference)
From
1.
2.
3.
4.
5.
the Drivers MENU you may make 4 selections:
nForce Chipset Installation Utility
Nvidia VGA Graphics Driver
Onboard LAN Driver
Realtek HD Audio Driver
Exit: Click to exit this installation menu.
- 43 -