Blomberg Dishwasher Installation manual

Dishwasher
Installation Manual
FOR MODELS
DWT 14210 NBL00
DWT 14220 NBL00
DWT 14240 NBL00
DWT 15210 NBL00
DWT 15220 NBL00
DWT 15240 NBL00
DWT 15211 NBL00
DWT 35220 NBL00
DWT 35240 NBL00
DWT 35200 NBL00
DWT 36210 NBL00
DWT 36220 NBL00
DWT 36240 NBL00
DWT 36211 NBL00
DWT 15221 NBL00
DWT 15241 NBL00
DWT 34210 NBL00
DWT 34220 NBL00
DWT 34240 NBL00
DWT 34200 NBL00
DWT 35210 NBL00
USA
DWT 36221 NBL00
DWT 36241 NBL00
DWT 36200 NBL00
DWT 36201 NBL00
DWT 37210 NBL00
DWT 37220 NBL00
DWT 37240 NBL00
DWT 37200 NBL00
Installation Manual
For Dishwasher Models
DWT 14210 NBL00
DWT 14220 NBL00
DWT 14240 NBL00
DWT 34210 NBL00
DWT 34220 NBL00
DWT 34240 NBL00
DWT 34200 NBL00
DWT 35210 NBL00
DWT 15210 NBL00
DWT 15220 NBL00
DWT 15240 NBL00
DWT 35220 NBL00
DWT 35240 NBL00
DWT 35200 NBL00
DWT 36210 NBL00
DWT 36220 NBL00
DWT 15211 NBL00
DWT 15221 NBL00
DWT 15241 NBL00
DWT 36240 NBL00
DWT 36211 NBL00
DWT 36221 NBL00
DWT 36241 NBL00
DWT 36200 NBL00
DWT 36201 NBL00
DWT 37210 NBL00
DWT 37220 NBL00
DWT 37240 NBL00
DWT 37200 NBL00
To prevent accidents, which could cause serious injury or death, as well as
machine damage read these instructions before installation and / or use.
Contents
1.
IMPORTANT SAFETY INSTRUCTIONS..........................................................................................1
1.1
INSPECT THE DISHWASHER.........................................................................................2
1.2
HOW TO CONTACT US ...................................................................................................2
2.
TOOLS WHICH MAY BE NEEDED...................................................................................................3
3.
MATERIALS WHICH MAY BE NEEDED
(Additional materials may be needed) ...............................................................................................3
4.
MATERIALS SUPPLIED
(If parts are missing contact your dealer or our customer service department) ................................4
4.1
PARTS SUPPLIED ...........................................................................................................4
4.2
MANUAL BAG ..................................................................................................................4
4.3
DISHWASHER PARTS BAG 1 .........................................................................................4
4.4
DISHWASHER PARTS BAG 2 .........................................................................................4
4.5
PARTS ATTACHED TO THE REAR OF THE DISHWASHER..........................................4
5.
DISHWASHER SPECIFICATIONS ...................................................................................................5
5.1
TECHNICAL FEATURES .................................................................................................5
6.
ENCLOSURE PREPARATION .........................................................................................................5
6.1
ELECTRICAL PREPARATION .........................................................................................5
6.2
PREPARATION / INSTALLING MOUNTING BRACKETS................................................6
6.3
ADJUSTING HEIGHT.......................................................................................................7
6.3.1 INSTALLING THE FOOT SUPPORTS .............................................................................7
6.4
INSTALLING THE SIDE TRIM STRIPS ...........................................................................7
6.5
PREPARING THE WATER CONNECTION (A) ................................................................8
6.5.1 INSTALLING THE 90° ELBOW FITTING (B) ...................................................................8
6.5.2 JUNCTION BOX PREPARATION (C)...............................................................................8
6.6
DRAIN PREPARATION ....................................................................................................9
6.6.1 UNDER THE SINK DRAIN ...............................................................................................9
6.6.2 INSTALLING AN AIR GAP................................................................................................9
6.6.3 DISPOSAL........................................................................................................................9
7.
PLACEMENT OF DISHWASHER INTO THE OPENING................................................................10
7.1
DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS ....10
7.1.1 DRAIN HOSE CONNECTION ........................................................................................10
7.1.2 PREPERATION OF WATER SUPPLY & ELECTRICAL CONNECTIONS......................11
7.1.3 WATER SUPPLY CONNECTION ..................................................................................13
7.1.4 ELECTRICAL CONNECTION ........................................................................................13
7.1.5 GROUDING INSTRUCTIONS ........................................................................................13
7.1.6 FASTEN JUNCTION BOX ..............................................................................................15
7.2
READJUSTING FOOT LEVELS.....................................................................................15
7.3
ADJUSTING THE MOVABLE TOE KICK .......................................................................16
7.4
INSTALLING THE OUTER DOOR .................................................................................17
8.
INSTALLER CHECKLIST ...............................................................................................................23
9.
FINAL INSTRUCTIONS ..................................................................................................................23
10.
SELF HELP HINTS .........................................................................................................................23
INTRODUCTION
Please read this installation manual and particularly
the safety instructions completely and carefully.
They will save you time and effort and help to
ensure optimum dishwasher performance.
Be sure to observe all listed warnings and cautions.
Look particularly for the icons with exclamation
marks inside. The information icon also will provide
important references.
WARNING
Ý
CAUTION
Notice
WARNING:Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTION:Indicates a potentially hazardous
situation which, if not avoided, may result
in injury. It may also be used to alert
against unsafe practices.
Notice:
Indicates a potentially hazardous
situation which, if not avoided, may result
in damage to the dishwasher, the tableware, the equipment or the environment.
1. IMPORTANT SAFETY
INSTRUCTIONS
=
The dishwasher installation must be performed in
accordance with this installation manual. If you did
not receive an installation manual, order it by calling
1-800-459-9848 or you may also download it from
our web site at www.Blombergappliances.com
=
Installation and repair should be performed by a
qualified installer. Work by unqualified persons
could be dangerous and may void the warranty.
=
Do not operate the appliance if damaged,
malfunctioning, partially disassembled or if it has
missing or broken parts.
=
Also follow the safety instructions of the user manual.
=
To reduce the risk of electric shock, fire, or injury
to persons, the installer must ensure that the
dishwasher is completely enclosed at the time of
installation.
=
Only connect the dishwasher to the power supply
when all installation and plumbing work is complete.
=
If the dishwasher is installed in a location that
experiences freezing temperatures (e.g. in a vacation
home, cabin, etc.), you must drain all the water
from the dishwasher’s interior. Water system
ruptures that occur as a result of freezing are not
covered by warranty.
=
Dishwasher must be secured to adjacent cabinetry
using the brackets provided. Failure to do this may
cause damage to property or bodily injury.
=
Connect to a properly rated, protected and sized
power supply circuit to avoid electrical overload.
The dishwasher is designed for an electrical supply
of 120 V (volts), 60 Hz (hertz), AC, connected to a
dishwasher-dedicated, properly grounded electrical
circuit with a fuse or breakers rated for 15 amperes.
Electrical supply conductors shall be a minimum of
# 14 AWG copper wire rated at 75 °C (167 °F) or
higher. These requirements must be met to prevent
injury and machine damage. Consult a qualified
electrician if in doubt.
=
Do not use any extension cord or portable outlet
device to connect the dishwasher to a power supply.
=
Ensure that any plastic wrappings, bags, small
pieces etc. are disposed of safely and kept out of
the reach of children. Danger of suffocation!
=
Remove the door to the washing compartment
when removing an old dishwasher from service or
discarding it. Ensure that the appliance presents
no danger to children while being stored for disposal.
=
Old appliances may contain materials that can be
recycled. Please contact your local recycling
authority about the possibility of recycling these
materials.
In addition to these instructions, the dishwasher shall
be installed:
=
In accordance with all local codes or, in absence
of a local code,
=
In the United States, with the National Electric
Code,
=
In Canada, with the Canadian Electric Code
C22.1-latest edition/Provincial and Municipal
codes and/or local codes.
Ý Notice :
Read these installation instructions completely before
installing and follow them carefully. Save these
installation instructions and pass them on to any
future user.
WARNING
When installing the dishwasher, follow basic
precautions, including the following:
1
Ý Notice :
=
=
=
=
The dishwasher drain hose must be installed with
a drain loop at least 28" (710 mm) off the cabinet
floor; otherwise the dishwasher may not drain
properly.
This dishwasher is intended for residential use
only, and should not be used in commercial
establishments.
New installation - If the dishwasher is a new
installation, most of the work must be done before
the dishwasher is moved into place.
Replacement - If the dishwasher is replacing
another dishwasher, check the existing dishwasher
connections for compatibility with the new
dishwasher, and replace parts as necessary.
1.1 INSPECT THE DISHWASHER
After unpacking the dishwasher and prior to
installation, thoroughly inspect the dishwasher for
possible freight or cosmetic damage. Report any
damage immediately.
Ý Notice :
=
Cosmetic defects must be reported within 10 days
of installation.
=
Do not discard any bags or items that come with
the original package until after the entire installation
has been completed.
HOW TO CONTACT US :
You may either call our Toll Free Number at
1-800-459-9848 or contact us via the web site at
www.Blombergappliances.com or Contact the
Blomberg Distributor for your State or Province as
listed on the Distributor Contact List provided.
2
2. TOOLS WHICH MAY BE NEEDED
Pipe Wrench
Wire Cutter
Drill
Hole Saw
Hammer
Wire Stripper
(T20)
Tape Measure
Torx Screwdriver
Phillips Screwdriver
Adjustable Wrench
Scot Screwdriver
Scissors
Level
Brush
Pencil
3. MATERIALS WHICH MAY BE NEEDED
(Additional materials may be required to comply with local codes)
Hot Water Supply Line - Minimum 3/8" O.D. copper tubing or metal braided dishwasher
supply line.
Electrical Supply Cable - Minimum #14AWG, 2 conductors, 1 ground, insulated copper
conductors.
90° elbow with 3/8" N.P.T. male threads on one leg, and sized to fit your water supply
line
(copper tubing/compression fitting, or braided hose) on the other leg.
UL listed conduit connector or strain relief.
Teflon tape or other pipe thread compound to seal plumbing connections.
Shut-off valve and fittings appropriate for hot water supply line (copper tubing/compression
fitting, or braided hose).
Slicone
Glue
3
a.
x1
b.
x1
c.
x1
d.
x6
e.
x1
f.
x1
g.
x1
h.
x1
i.
x4
j.
x1
k.
x1
l.
x1
m.
x3
n.
x4
o.
x1
p.
x1
r.
x2
s.
x2
t.
x2
u.
7 3/4”(196,5mm)
x1
v.
x8
y.
x4
4. MATERIALS SUPPLIED
4.1 PARTS SUPPLIED
Parts for your dishwasher will come in several plastic bags.
Check your parts bags shown to make sure you have all
the parts as listed to the left.
4.2 MANUAL BAG
The dishwasher comes with a manual bag containing:
= User manual,
= Installation manual and
= Quick reference guide.
4.3 DISHWASHER PARTS BAG 1
This dishwasher bag comes with the following parts:
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
k.
l.
m.
n.
o.
p.
r.
s.
t.
Side Trim Strips (Left)
Side Trim Strips (Right)
Adjusting Wrench
Screws Ø 1/8" x 5/8" (Ø 3.5 mm x 14 mm)
Mounting Bracket Left
Mounting Bracket Right
Spring Clamp
Screw Clamp
Short Leg Supports
Rubber Connector
Toe Kick Bracket - Left
Toe Kick Bracket - Right
Wire Nuts
Clips
Toe Kick (toe kick without slots)
Toe Kick
Screws Ø 1/8" x 3/8" (Ø 3.9 mm x 9 mm)
Plastic Caps
Screws Ø 1/8" x 5/8" (Ø 3.5 mm x 14 mm)
4.4 DISHWASHER PARTS BAG 2
In addition to the manual bag and the dishwasher parts
bag 1 DWT 34, DWT 35 and DWT 36, DWT 37 (dishwasher
models which can accept a wooden kitchen door) also come
with a door panel installation kit which contains:
u. Template
v. Screws Ø 1/8" x 5/8” (Ø 3.5 mm x 14 mm)
y. Screws Ø 3/16" x 13/4” (Ø 4 mm x 43 mm)
4.5 PARTS ATTACHED TO THE REAR OF THE
DISHWASHER
a.
b.
o.
p.
Side Trim Strips (Left)
Side Trim Strips (Right)
Toe Kick (toe kick without slots)
Toe Kick
4
34” - 361/4”
(864mm - 920mm)
5. DISHWASHER SPECIFICATIONS
33 7/8- 35 7/8”
(861mm - 911mm)
239
(598 /16”
mm
)
24”m)
0m
1
(6
2
(61 4”
0m
m)
5.1 TECHNICAL FEATURES
Load capacity
axax)
” mm
4
2 m
0m
61
(
12 place settings
Permissible water pressure 4.35 - 145 psi (0.3 - 10 bars)
Electrical connection
120 V (volts), 12 A (amps), 60 Hz (hertz)
Total power
1200 W (watts)
Heater power
1000 W (watts)
Because we continually strive to improve our products, we
may change our specifications and design without prior
notice. This device corresponds to the following directives:
UL 749 Household Dishwasher directive.
6. ENCLOSURE PREPARATION
Ý Notice :
=
For proper dishwasher operation and appearance ensure
that the enclosure has the minimum dimensions shown
in the figure above.
6.1 ELECTRICAL PREPARATION
WARNING
(
”)
30
To avoid electrical shock and/or a fire hazard, make
sure electrical work is properly installed. Only qualified
electricians should perform electrical work.
Before installation disconnect the power supply to the
work area by unplugging the unit, "tripping" the circuit
breaker or removing the fuse.
The installer has the responsibility of ensuring that the
dishwasher electrical installation is in compliance with
all national and local electrical codes and ordinances.
The dishwasher is designed for an electrical supply of
120 V, 60 Hz, AC, connected to a dishwasher-dedicated,
properly grounded electrical circuit with a fuse or breaker
rated for 15 amperes.
WARNING
Figure A
Electrical supply cords must be a minimum #14AWG
copper wire.
Position the cable extending approximately 30" (760 mm)
from the enclosure's back (Figure A).
5
Position the cable extending at the bottom edge
(Figure B).
Figure B
Remove 2 15/16" - 3 15/16" (75mm-100mm) of the cable's
outer casing, and then remove 3/8"-1/2" (9-13mm) of
insulation from each wire. (Figure C)
Figure C
6.2 PREPARATION FOR INSTALLING
MOUNTING BRACKETS
WARNING
Dishwasher must be secured to adjacent cabinetry using
the mounting brackets provided. Failure to do this may
cause damage to property or bodily injury.
A
B
A
B
Place the two mounting brackets into the top corners of the
dishwasher.
Fix the mounting brackets (A) to the top corners of the
dishwasher, with the screws supplied.
Bend sides of mounting brackets (B) in order to fix from
sides (if necessary)
6
(861mm - 911mm)
6.3. ADJUSTING HEIGHT
33 7/8- 35 7/8”
Insert the short leg supports into the legs of the dishwasher.
11/8”
(50mm)
Supplied (4)
11/8”
(50mm)
Adjust the front foot level with the adjusting wrench to balance
and raise the dishwasher to the enclosure height.
Adjust the rear foot level with a screwdriver to balance and
raise the dishwasher to the enclosure height.
Ý Notice :
=
Make sure the dishwasher is plumb and notice dishwasher
can be placed with a small clearance under the counter
top.
Turning the screwdriver in the direction of the black arrows
will bring the dishwasher back feet up.
= Turning the screwdriver in the direction of the white arrows
will take the dishwasher rear feet down.
=
T20
6.4 INSTALLING THE SIDE TRIM STRIPS
1. Remove the adhesive tape (Figure A).
Place the trim strips on the front edge of the side walls
(Figure B).
Figure A
Figure B
7
6.5 PREPARING THE WATER CONNECTION (A)
Install an easily accessible shut-off valve (not supplied) in
the water supply line. All solder connections must be made
before the water line is connected to the dishwasher’s water
inlet valve. Water can also be supplied to the dishwasher
by using a flexible braided hose line.
Check with your plumbing supply sources for the proper
hose and 90° elbow and necessary fittings for the water
supply line. This material is not supplied, and must be
purchased separately.
WARNING
Installation should be performed by a qualified installer.
Work by unqualified persons could be dangerous and
may void the warranty.
If the dishwasher is installed in a location that
experiences freezing temperatures (e.g. in a vacation
home, cabin etc.), you must drain all the water from the
dishwasher's interior. Water system ruptures that occur
as a result of freezing are not covered by warranty.
6.5.1 INSTALLING THE 90° ELBOW FITTING (B)
B
CAUTION
Do not over tighten the 90° elbow. Doing so may damage
the water inlet valve and cause a water leak.
A
If the water supply line is to be copper tubing, make certain
that the elbow has a compression fitting. Apply Teflon tape
or other pipe sealant when required. Orient the water supply
connection on the left side as shown in the figure so the
water line can be easily pulled underneath or on the side of
the dishwasher.
6.5.2 JUNCTION BOX PREPARATION (C)
Remove the junction box cover by removing the screw as
shown in the figure. They will be reinstalled later.
C
8
6.6 DRAIN PREPARATION
The dishwasher drain hose may be connected to the drain
plumbing in one of three ways (Figure A, B, C).
Ý Notice :
Either one of the above methods must be used or the
dishwasher will not operate properly.
= A hose that attaches to a sink spray can burst if it is
installed on the same water line as the dishwasher. If
your sink has one, it is recommended that the hose be
disconnected and the hole plugged.
= The total length of the drain hose is 76 3/4” (1950mm.)
If a hose extension is required, a drainage hose of equal
quality must be used.
The maximum length must not exceed 157 1/2” (4000mm)
Otherwise, the cleaning process is negatively influenced.
=
6.6.1 UNDER THE SINK DRAIN
Install a Y-branch tail pipe. (Figure A)
Ý Notice :
=
Figure A
You must add a loop at least 28" (710 mm) above the
floor of the cabinet and above the drain connection in
the drain hose to prevent waste water from not draining
properly, and causing either poor washing results or a
bad odor.
6.6.2 INSTALLING AN AIR GAP
If the local ordinance requires an air gap (Figure B).
Ý Notice :
=
Check with local ordinance for type of air gap required.
Figure B
6.6.3 DISPOSAL
Remove the drain connection plug before attaching the
drain hose from the dishwasher.
Every disposal has a hook up for a dishwasher; consult
your disposer manual for correct connection. (Figure C)
Figure C
9
7 PLACEMENT OF DISHWASHER INTO THE
OPENING
Now place the dishwasher into the opening and get ready
to connect all hoses and electrical connections.
CAUTION
Make sure all hoses and electrical wire are pulled through
the side opening of the cabinet, no hoses are kinked
and all slack is taken out as shown in the above figure.
7.1
DRAIN HOSE CONNECTION, WATER
SUPPLY & ELECTRICAL CONNECTIONS
7.1.1 DRAIN HOSE CONNECTION
Connect the drain hose to the drain plumbing.
1. Use the supplied rubber connection hose and drain hose
clamps to connect the dishwasher drain hose to the
plumbing drain connection.
2. Use the spring clamp to secure the rubber connection
hose to the dishwasher drain hose. Use the screw clamp
to secure the rubber connection hose to the plumbing
drain connection.
Note that the marks on the
rubber connection hose
should be on the drain
hose side
10
7.1.2 PREPERATION OF WATER SUPPLY & ELECTRICAL CONNECTIONS
Left side water
supply connection
Right side electrical
supply connection
Figure A
Figure A
Figure B
Figure B
Figure C
Figure C
Figure D
Figure D
11
Before pushing the dishwasher in to the
cabinet you must place the electrical
cables and water supply hoses into the
channels of the dishwasher (Figure A)
Place the supplied clips into the channels
(Figure B) so that you can move these
clips along the channels (Figure C) and
fix by pressing on (Figure D) so that you
can keep the electrical cable and water
supply hose in the channels.
Figure E
After installing one clip for each side
push the dishwasher into the
cabinet (Figure E).
Figure F
Figure F
Figure G
Figure G
12
Note that while pushing the
dishwasher into the cabinet,
electrical cable and water supply
hose must move in the channels to
the front (Figure F).
Fix the second clip for both sides
(Figure G).
7.1.3 WATER SUPPLY CONNECTION
Water supply may be connected to the dishwasher in one
of two ways:
= With metal braided hose.
= With copper tubing.
After connections are made turn on the water supply to
check for leaks.
CAUTION
=
Hot water supply line: Use minimum 3/8” O.D. copper
tubing or metal braided dishwasher supply line.
=
Temperatures required for soldering and sweating
will damage the dishwasher’s water inlet valve so
if any such operation is needed, keep the heat
source min. 7 7 / 8 ” (200 mm) away from the
dishwasher’s water inlet valve.
=
There should not be any sharp bends in the water
line that may restrict the water flow.
=
Teflon tape or pipe tread compound must be used
for sealing the connection. Before connecting the
copper water supply line to the dishwasher, flush
it with hot water to clear any foreign material.
Ý Notice :
After connections are made turn on the water supply to
check for leaks.
7.1.4. ELECTRICAL CONNECTION
WARNING
=
Make sure the voltage and frequency listed on the
data plate correspond with the household electrical
supply. This data must correspond to prevent injury
and machine damage. Consult a qualified electrician
if in doubt.
=
Only connect the dishwasher to the mains when
all installation and plumbing work is complete.
=
Do not use any extension cord or portable outlet
device to connect the dishwasher to a power supply.
7.1.5. Grounding Instructions
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for
electric current. This appliance must be installed and
grounded in accordance with all local codes and ordinances.
13
WARNING
=
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded.
Install a strain relief (not supplied) into the opening on
the kick plate. (Figure A)
Figure A
Pass the electrical supply cable through the strain relief;
make sure the strain relief clamps the insulated outer
casing of your electrical supply cord and not the wires
themselves. Leave 215/16" " to 315/16" " (75 mm / 100 mm)
of insulated wire extending through the strain relief
(Figure B). Tighten the strain relief screws. (Make sure
you can not pull the electrical cord out) of the strain relief.
Figure B
Do not pre-twist the wires before connecting them with
wire nuts.
Using the supplied wire nuts, connect the electrical supply
wires to the dishwasher’s wires, black to black, white to
white, and green or bare to green or bare. Make certain
that the insulated wires show no bare wire from the
bottoms of the wire nuts. Gently tug the wires to make
certain they are securely connected.
(Figure C)
Figure C
14
7.1.6. FASTEN JUNCTION BOX
1. Pull the wires into the junction box. Be sure that the
wire nuts do not loosen.
2. Replace the cover on the junction box.
3. Secure the cover with the screws (Figure D).
Figure D
7.2 READJUSTING FOOT LEVELS
Now that the dishwasher is in the cabinet you must
readjust the feet to bring the dishwasher up to the
required height and attach it underneath the countertop.
1. Readjust the front foot levels with adjusting wrench
to balance the dishwasher and raise it up under the
countertop, make sure the unit is level.
Ø 1/8" (3,5mm)
Ø 1/8" (3,5mm)
2. Readjust the rear foot levels with a screwdriver to
balance the dishwasher and raise it to the required
height using the brackets supplied.
3. Attach the dishwasher underneath the countertop
with the four screws supplied (Ø 1/8" x 5/8" - Ø 3.5 mm
x 14 mm). Make sure you do not go through the top
of the countertop or damage granite.
15
7.3 ADJUSTING THE MOVABLE TOE KICK
Now that you have successfully installed the dishwasher,
you need to attach the toe kick to the dishwasher. The two
piece toe kick can be adjusted to the height and depth
needed for your kitchen. Be sure to use the slotted toe kick
in the front and the other behind it. They slide into each
other.
A
1. Insert the movable toe kick brackets into the channel
( A).
2. Make sure that the plastic tab to the left of the “L” opening
on the dishwasher has not closed the channel you will
push the bracket through.
Ý Notice :
B
Be sure to notice there is a left and a right bracket.
Adjust the toe kick brackets forward or backwards so that
they will align with the kitchen toe kick (B).
Lock the toe kick brackets as shown with the plastic tab in
the figure C by pushing the plastic tab on the dishwasher
into the teeth of the bracket (C).
3. Now attach the toe kick to the bracket with the two
(Ø 1/8" x 5/8” - Ø 3.5 mm x 14 mm) screws and the caps
provided as follows.
C
If the enclosure height is below 341/14” (870 mm) use only
“o” labelled toe kick (toe kick without slots). Installation
should be done following the steps illustrated in the Figures
A, B and C respectively.
A
1. Bend tabs on toe kick (o) inwards (A).
2. Secure toe kick to brackets with screws (t) as shown in
the supply bags (B).
3. Attach caps (s) as shown in the supply bags (C).
o
B
t
s
C
16
If the enclosure height is above 341/14” (870 mm) use “o”
and “p” labelled toe kicks together. Make sure the slotted
toe kick “p” is on the outside so you can adjust height of the
toe kick. Installation should be done following the steps
illustrated in the figures A, B and C respectively.
A
p
o
1. Align the toe kick (o) and (p) (A).
B
2. Secure toe kicks to brackets with screws (t) after adjusting
the height of the slotted toe kick (p) (B).
t
s
3. Attach caps (s) as shown in the supply bags (C).
C
7.4 INSTALLING THE OUTER DOOR
(DWT 34200, DWT 35200, DWT 36200, DWT 37200)
Measure the height and width of the enclosure (Figure A)
and the toe kick. Determine how big the wooden door can
be. For example if the height is 34’’ (864 mm) and if the toe
kick is 315/16’’ (100 mm) the door can not be taller than
30” (762 mm).
?
1. Prepare the wooden door with the mounting brackets.
Height
: Height of the wooden door 30” (762 mm)
Width
: 23 ¼” to 23 ½” (592 mm - 595 mm)
Thickness : ¾ “ (19 mm)
?
Figure A
2. Remove the plastic mounting brackets from the
dishwasher (Figure B).
Figure B
17
3. Lay the schematic over the door from the bottom up and
mark holes on the wooden door as shown in the drawing
(Figure A).
” )
m
8 ,2m
1
(22
6
11 / 1
A
A
A
A
6” )
11 / 1 m
8 ,2m
1
(22
11 / 1
”
6
8 1,2m
2
(2
m
)
4. Place the plastic mounting brackets over the marked
holes and the side tabs must be flush with the edge of
the wooden door (Figure B).
Side Tab
B
5. Attach the two mounting brackets to the wooden door
with eight screws (Ø 1/8" x 5/8" (Ø 3.5 mm x 14 mm)
(Figure C).
v
Ø 1/8" (3,5mm)
C
18
X8
6. Cut the small tabs on the mounting brackets off
(Figure A).
7. Cut the side tabs on the plastic mounting brackets off.
A
8. Mount the wooden door onto the dishwasher with the
plastic mounting brackets which you have attached
(Figure B).
B
9. Open the door and remove the two caps and two screws
inside the door at position 1 and 3 (Figure C).
C
19
10. Using the four screws Ø 3/16"x 111/16" (Ø 4 mm x 43
mm) provided, attach the wooden door to the
dishwasher at position 1 and 3 (Figure A).
Ø 3/16" (4mm)
x4
y
A
11. Check the position of the wooden door and make sure
it is aligned properly (Figure B).
B
12. Tighten the screws in position 1 and 3 completely after
the final alignment (Figure C).
Ø 3/16" (4mm)
x4
y
C
20
1 3 . Check whether the bottom of the door hits the toe kick
of the kitchen cabinet (A).
13.1 If the door hits the toe kick cut the necessary section
out of the toe kick (B).
13.2 Apply silicon or sealant to the cut edge of the kitchen
cabinet toe kick or paint so it does not absorb moisture.
B
A
ADJUSTING DOOR TENSION WITH CUSTOM
WOODEN DOOR
(DWT 34200, DWT 35200, DWT 36200, DWT 37200)
C
Check the door tension of the dishwasher: If the door closes
too quickly or if the door falls open, the spring tension needs
to be adjusted.
The adjustment screws can be found on the front of the
dishwasher after you open the door (see drawing).
Adjust the spring tension by turning the screw to the right
for more weight and to the left for less weight (Figure C).
0 kg
21
Ý Notice :
If you have a European kitchen or want to install a wooden toe kick to match your kitchen, please refer to one
of the two drawings given below. Follow the same instructions on the brackets as for the removable toe kick.
Installation should be done following the steps illustrated in the figures A, B, C, D respectively.
See also pages 15 - 16
B
C
t Ø 1/8" (3,5mm)
A
”
7 / 16 m)
21 44m
(5
3/8” (10mm)
19
/
16
D
”4
0m
m
See also page 21
B
A
C
22
Ý Notice :
Ý Notice :
The installer is responsible for the dishwasher
installation. Incorrect installation is not covered by
the warranty.
8. INSTALLER CHECKLIST
Your installer must have completed and checked
the following:
=
The dishwasher is square and level.
=
The dishwasher is fastened securely to the
cabinetry.
=
The dishwasher door opens and closes freely.
The dishwasher door must close without hitting
any cabinetry or counter top.
=
The inlet water supply is turned on and checked
for leaks.
=
The drain hose has been connected and checked
for leaks. There must be no kinks or obstructions
in the drain hose.
=
The drain hose must be installed with a 28" (710
mm) high drain loop for drain hook-ups without
any air removed.
=
If the dishwasher drain is hooked up to a garbage
disposal, the drain hopper plug must be removed.
=
The spray arms are free and rotate freely.
=
The rinse cycle has been run.
=
The water level will be below the filter screen
after the end of the wash program. It is normal
to find some water in the drain filter area.
=
Set the water softener to the correct water
hardness for your area. If the dishwasher drain
is connected to a garbage disposal, make sure
that the drain/hopper plug has been removed.
If the dishwasher does not operate properly, refer to the
self help hints.
10. SELF HELP HINTS:
The power indicator light doesn’t come on:
Check to make sure the breaker to the dishwasher
is in the on position.
= Check all the wire connections in the junction box
are tight and not loose.
=
No Water is coming into the dishwasher:
=
Check to make sure the hot water shut-off is in the
ON position.
Water does not drain:
Make sure drain hose is not kinked or comes out of
air gap next to the sink.
= Remove drain hose from disposal making sure plug
is removed.
=
Ý Notice :
=
If your dishwasher is not operating properly after
following these steps: Contact your dealer to
schedule an authorized service agent to inspect
your new dishwasher for any function related failure.
=
The manufacturer warranty does not cover
installation or customer education service visits.
DWT xxxxx xxxxx
You will find the model and serial number information
on the label located on the right-hand side of the inner
door of your dishwasher, as shown above.
9. FINAL INSTRUCTIONS
1. Press the On/Off button to turn the dishwasher
on.
2. Power indicator light comes on.
Ý Notice :
Please make a copy of your invoice and keep it with this
manual and register your dishwasher on-line.
3. Use the Cycle Select button to choose a washing
program.
4. Start the program with the Start/Pause button.
5. Run the dishwasher through one complete cycle.
When the progress indicator light “End” lights
up, the wash cycle is completed. Use the On/Off
button to turn the dishwasher off.
Installation Manual-USA
23
17 1156 01 00-00 USA