U.S. Range PS-4-20 Technical data

Operating manual
PacDriveTM
PS-4 and PD-8
ELAU On the best machines
PD_OperaManPS-4_us
Article number: 17130094-001
Edition: 08.2003
Impressum
Imprint
No part of this documentation and the related software and firmware may be reproduced, rewritten, stored on a retrieval system,
transmitted or translated into any other language or computer language without the express written consent of ELAU AG.
All possible measures were taken to ensure the that this product
documentation is complete and correct. However, since hardware
and software are continuously improved, ELAU makes no representations or warranties with respect to the contents of this product
documentation.
Trademarks
PacDrive is a registered trademark of ELAU AG.
Korrekturausdruck
© All rights reserved to ELAU AG, also in case of patent right
applications.
page 2
ELAU AG
Dillberg 12
D-97828 Marktheidenfeld
ELAU Inc.
165 E. Commerce Drive
Schaumburg, IL 60173 - USA
Phone:
Fax:
09391/606-0
09391/606-300
Phone:
Fax:
+1 847 490 4270
+1 847 490 4206
eMail:
Internet:
info@elau.de
www.elau.de
e-mail:
Internet:
info@elau.com
www.elau.com
PacDrive PS-4 / PD-8
ELAU AG
PD_OpManPS-4_00_us.FM
All other trademarks mentioned are the exclusive property of their
manufacturers.
Contents
PD_OperaManPS-4_usIVZ.fm
Korrekturausdruck
Contents
1
On this manual
1.1
1.2
Introduction ............................................................................................ 5
Symbols, Signs and Forms of Depiction ................................................ 6
2
General Safety Notes
2.1
2.2
2.3
2.4
2.5
2.5.1
2.5.2
2.5.3
2.5.4
Basics .................................................................................................... 7
Depiction of Safety Notes ...................................................................... 8
Use as Directed ..................................................................................... 9
Selection and Qualification of Staff ...................................................... 10
Residual Risks ..................................................................................... 10
Installation and Handling ..................................................................... 11
Protection against Touching Electrical Parts ....................................... 12
"Safely Separated Low Voltages" ........................................................ 13
Potentially Dangerous Movements ...................................................... 14
3
System Overview
15
3.1
3.2
3.3
3.4
Drive Concepts for Packaging Machines .............................................
Structure of the PacDrive™ Automation System .................................
Structure ..............................................................................................
Components ........................................................................................
15
17
18
19
4
Transportation, Storage, Unpacking
21
4.1
4.2
4.3
Transportation ...................................................................................... 21
Storage ................................................................................................ 21
Unpacking ............................................................................................ 21
5
Maintenance
25
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.7.1
5.8
5.8.1
5.8.2
Spare Parts, Components ...................................................................
Repair ..................................................................................................
Service Addresses ...............................................................................
Exchanging units .................................................................................
Cleaning ...............................................................................................
EMC Rules ...........................................................................................
Commissioning ....................................................................................
Slaves in the SERCOS ring .................................................................
Configuration / Programming / Diagnosis ............................................
Diagnosis LEDs ...................................................................................
Combination of PacDrive SCL and PacDrive PS-4 .............................
25
26
26
27
29
30
31
35
35
36
37
ELAU AG
5
PacDrive PS-4 / PD-8
7
page 3
5.9
5.9.1
5.9.2
Order numbers ..................................................................................... 38
PacDrive PS-4 ...................................................................................... 38
Cables .................................................................................................. 39
6
Project definition
6.1
6.2
6.2.1
6.2.2
6.3
Creation of a PacDrive PS-4/PD-8, SCL055 application ...................... 41
PacDrive PS-4 ...................................................................................... 41
Mains Connection of PacDrive PS-4 .................................................... 41
Transformer dimensioning .................................................................... 44
Electricity Supply via Slip Ring ............................................................. 46
7
Technical Data
7.1
7.1.1
7.1.2
7.1.3
7.2
7.2.1
7.2.2
7.2.3
7.3
7.4
PacDrive PS-4 ...................................................................................... 47
General ................................................................................................. 47
Electrical connections ........................................................................... 48
Dimensions ........................................................................................... 51
PacDrive PD-8 ...................................................................................... 52
General ................................................................................................. 52
Electrical connections ........................................................................... 53
Dimensions ........................................................................................... 54
Declaration by the manufacturer .......................................................... 57
Modifications ........................................................................................ 58
8
APPENDIX
8.1
8.2
8.3
8.4
8.5
Contact ................................................................................................. 59
Further Literature .................................................................................. 60
Product Training ................................................................................... 62
Index ..................................................................................................... 63
Form for Error Report ........................................................................... 65
41
47
Korrekturausdruck
Contents
PD_OperaManPS-4_usIVZ.fm
59
page 4
PacDrive PS-4 / PD-8
ELAU AG
Korrekturausdruck
1.1 Introduction
1
On this manual
1.1
Introduction
Before using ELAU components for the first time, you should
familiarize yourself with this operating manual.
In particular, observe the safety notes described in chapter 2.
Only persons who meet the criteria for "Selection and Qualification
of Staff" (see chapter 2.4) are allowed to work on ELAU
components.
One copy of this manual has to be available for staff working on the
components with access at any time.
This manual is to help you use the component safely and expertly
and to use it as directed.
Observe this manual. This will help to avoid risks, reduce repair
costs and down times and increase the lifetime and reliability of the
products.
PDM_VerwendStd_us.FM
You also need to observe the valid rules for the prevention of
accidents and for environmental protection in the country and place
where the device is used.
ELAU AG
PacDrive EPAS-4
page 5
1 On this manual
1.2
Symbols, Signs and Forms of Depiction
Depiction
Meaning
„
First level enumeration sign.
–
Second level enumeration sign.
Action symbol: The text following this symbol includes an instruction for action. Execute the instruction
actions in the given order, from top to bottom.
9
Result symbol: The text following this symbol contains the result of an action.
Italics
Serif font
Korrekturausdruck
The following symbols and signs are used in this document:
If the describing text contains special terms (e.g.
parameters) these are written in italics.
If the manual contains program code, this is marked
by Serif font.
Information symbol: This symbol marks notes and
useful tips for using the product.
Warning sign: Safety notes can be found in the relevant places. They are marked by this symbol.
After this symbol, information about contents of the
chapter follows as guideline assistance.
PDM_VerwendStd_us.FM
Table 1-1: Symbols, signs and forms of depiction
page 6
PacDrive EPAS-4
ELAU AG
2.1 Basics
Korrekturausdruck
2
General Safety Notes
This chapter contains general requirements for working safely.
Every person using ELAU components or working on ELAU
components has to read and observe these general safety notes.
If activities involve a residual risk, you will find a clear note in the
respective places. The note describes the risk that may occur and
preventive measures to avoid that risk.
2.1
Basics
The ELAU components are built according to the state of
technology and generally accepted safety rules. Nevertheless, their
use may cause a risk to life and limb or material damage if:
„ you do not use the components as directed
„ work on the components is not done by experts or instructed
staff
„ you inexpertly alter or modify a component
„ you fail to test the protective measures in place after installation,
commissioning or servicing
„ you do not observe the safety notes and regulations.
Only operate the components in perfect technical condition, as
directed, with regard to safety and risks and observe this manual.
The flawless and safe operation of the components requires
appropriate transport, storage, mounting and installation as well as
careful maintenance.
In case of any circumstances that impair the safety and cause
changes in the operating behavior, immediately put the
component(s) to a stop and inform the service staff in charge.
PDM_SicherhMax_us_neu.fm
In addition to this manual, observe
„ the prohibiting, warning and mandatory signs on the component,
the connected components and in the switching cabinet
„ the relevant laws and regulations
„ the operating manuals of the other components
„ the universally valid local and national rules for safety and the
prevention of accidents.
ELAU AG
PacDrive
page 7
2 General Safety Notes
2.2
Depiction of Safety Notes
The safety notes in this manual are grouped into different risk
categories. The table below shows which risk and possible
consequences the symbol (pictograph) and the signal words
indicate.
Pictograph
Signal word
Definition
DANGER!
Indicates an immediately dangerous
situation that will result in death or very
serious injuries if the safety rules are
not observed.
WARNING!
Indicates a possibly dangerous
situation that can result in serious
injuries or major material damage if the
safety rules are not observed.
CAUTION!
Indicates a possibly dangerous
situation that might result in material
damage if the safety rules are not
observed.
Korrekturausdruck
Risk categories
PDM_SicherhMax_us_neu.fm
Table 2-1: Risk categories
page 8
PacDrive
ELAU AG
2.3 Use as Directed
Korrekturausdruck
2.3
Use as Directed
The ELAU components are designed for installation in a machine/
plant or for combination with other components to form a machine/
plant. The components may only be used under the installation and
operating conditions described in this documentation. You must use
the accessories and ancillary parts (components, cables, etc.)
mentioned in the documentation. You must not use any foreign
objects or components that are not explicitly approved by ELAU.
"Use as directed" also means that you
„ observe the Operating Manuals and other documentations (see
appendix),
„ observe the instructions for inspection and maintenance.
Use other
than directed
The operating conditions at the place where the device is used
must be checked on the basis of the given technical data
(performance information and ambient conditions) and observed.
The device must not be put into operation until it is guaranteed that
the useable machine or the plant in which the motor is installed
meets in its entirety EC directive 98/37/EC (machine directive).
PDM_SicherhMax_us_neu.fm
In addition, observe the following norms, directives and regulations:
„ DIN EN 60204 Safety of machines:
Electrical equipment of machines.
„ DIN EN 292 part 1 and part 2 Safety of machines:
Basics, general design guidelines.
„ DIN EN 50178 Equipment of high-voltage plants with electronic
operating means.
„ EMC directive 89/336/EEC
ELAU AG
PacDrive
page 9
2 General Safety Notes
2.4
Selection and Qualification of Staff
Only qualified staff can recognize the significance of safety notes
and implement them accordingly.
This manual is aimed in particular at design and application
engineers in the fields of mechanical and electrical engineering, at
programmers, service and commissioning engineers.
Working on
electrical
equipment
Work on electrical equipment must only be done by qualified
electricians or by instructed staff supervised by an electrician
according to the electrotechnical rules.
An electrician is a person who, due to his vocational training, knowhow and experience as well as knowledge of the valid regulations,
is able to:
„ evaluate the work he is supposed to do
„ identify potential risks
„ implement suitable safety measures.
2.5
Korrekturausdruck
This manual is aimed exclusively at technically qualified staff with
detailed knowledge in the field of automation technology.
Residual Risks
PDM_SicherhMax_us_neu.fm
We minimized the health risk for people by means of appropriate
construction and safety technology. Nevertheless, there is a
residual risk, since the components work with electrical current and
voltage.
page 10
PacDrive
ELAU AG
2.5 Residual Risks
2.5.1
Installation and Handling
Korrekturausdruck
WARNING!
PDM_SicherhMax_us_neu.fm
Risk of injury while handling the unit!
Risk of injury due to squeezing, cutting or hitting!
„ Observe the universally valid construction and safety rules for
handling and installation.
„ Use suitable installation and transport facilities and use them
professionally. If necessary, use special tools.
„ Take precautions against squeezing.
„ If necessary, use suitable protective clothing (e.g. safety
glasses, safety shoes, protective gloves).
„ Do not stay under pending loads.
„ Remove any leaking liquids from the floor immediately to avoid
skidding.
ELAU AG
PacDrive
page 11
2 General Safety Notes
Protection against Touching Electrical Parts
Touching parts carrying a voltage of 50 Volts or higher can be
dangerous. When electric appliances are operated, certain parts of
these appliances inevitably carry a dangerous voltage.
DANGER!
High voltage!
Life hazard!
„ Observe the universally valid construction and safety rules for
working on high-voltage units.
„ After installation, check the fixed connection of the earth
conductor on all electric appliances according to the connection
plan.
„ Operation, even for short-term measuring and test purposes, is
only permitted with an earth conductor firmly connected to all
electric components.
„ Before accessing electrical parts with voltages exceeding 50
Volts, disconnect the unit from mains or power supply and lock it
out. After switching off, wait for at lest 5 minutes before touching
any components.
„ Do not touch electrical connections of the components while the
unit is on.
„ Before switching on the unit, cover all voltage carrying parts to
prevent accidental contact.
„ Provide for protection against indirect touching (EN 50178 /
1998 section 5.3.2).
Korrekturausdruck
2.5.2
DANGER!
PDM_SicherhMax_us_neu.fm
High leak current!
Life hazard!
„ The leak current is greater than 3.5 mA. Therefore the units
must have a firm connection to the power grid (according to DIN
EN 50178 / 1998 - equipment of high-voltage systems).
page 12
PacDrive
ELAU AG
2.5 Residual Risks
"Safely Separated Low Voltages"
PELV
Protective-ExtraLow-Voltage
Signal voltage and control voltage of the PacDrive units are <33 V.
In this range the specification as PELV system according to IEC
364-4-41 includes a protective measure against directly and
directly touching dangerous voltages by means of a "safe
separation" from the primary to the secondary side in the plant/
machine. ELAU urgently recommends to execute the plant/
machine with safe separation.
Korrekturausdruck
2.5.3
DANGER!
High voltage due to wrong connection!
Life hazard or risk of serious injury!
„ Only units, electric components or cables with a sufficient safe
separation of the connected power supplies according to EN
50178 / 1998 (equipment of high-voltage systems with electronic
operating means) may be connected to the signal voltage
connections of these components.
„ Make sure that the existing safe separation is retained
throughout the entire current circuit.
When using ELAU components in systems that do not include a
safe separation as a means of protection against directly or
indirectly touching dangerous voltages, all connections and
contacts (e.g. MAx-4, Sub-D connector, serial inerface) that do not
comply with protection class IP2X must be permanently covered.
The cover or device connection must be such that it can only be
removed with the help of a tool. The protective measure must be
observed on all connected devices.
PDM_SicherhMax_us_neu.fm
FELV
FunctionalExtra-LowVoltage
ELAU AG
PacDrive
page 13
2 General Safety Notes
Potentially Dangerous Movements
There can be different causes for potentially dangerous
movements:
„ mistakes in wiring or cable connection
„ software errors
„ faulty components
„ errors in measuring value and signal encoders
„ operating mistakes
The protection of people must be insured by superior means or
monitoring on the plant side. You must not rely on the internal
monitoring in the drive components alone. Monitoring or measures
are to be provided according to a risk and error analysis by the
plant builder according to the specific conditions of the plant. The
valid safety rules for the plant are to be included in this process.
Korrekturausdruck
2.5.4
DANGER!
PDM_SicherhMax_us_neu.fm
Potentially dangerous movements!
Life hazard, serious injury or material damage!
„ No persons are allowed within the motion range of the machine.
This is to be ensured by means of devices like protective fences,
grids, covers or photoelectric barriers.
„ The fences and covers must be sufficiently strong to withstand
the maximum possible motion energy.
„ The emergency stop switch must be located very close to the
operator. Check the operation of the emergency stop before
starting up the plant.
„ Secure against unintentional start by enabling the mains
contactor of the drives via an emergency off circuit or by means
of the function 'safe stop'.
„ Before accessing the danger zone, bring the drives to a safe
stop.
„ To work on the plant, power must be turned off and locked out.
„ Avoid operating high-frequency, remote-control and radio
devices in the vicinity of the plant's electronics and connecting
wires. If the use of those devices is inevitable, check system and
plant for possible malfunctions before first operation. In some
cases a special EMT check may be necessary.
page 14
PacDrive
ELAU AG
Hard-copy for correction
3.1 Drive Concepts for Packaging Machines
3
System Overview
3.1
Drive Concepts for Packaging Machines
Modern machine concepts in the packaging industry are
characterized by the need for high dynamism, flexibility, modularity
and efficiency. Packaging machines were traditionally equipped
with a main drive and a mechanical main shaft, which coupled all
other motion organs in the machine usually with mechanical
components with complicated motion functions. Designing such
packaging machines flexibly for different products is a highly
complex task. Even minor changes in the packaging process,
particularly in case of a product change, require major
modifications and down time.
Packaging machines with electronic vertical shafts, by contrast,
permit full flexibility. Electronic servo drive systems replace cam
and coupling gears, and a virtual electronic main shaft ensures that
the motion axes are synchronous. Any pulse and angle
synchronous movements are determined by a central controller.
PD_SysUebersSCL_us.fm
Unplanned machine states, such as stop or emergency off
situations and initialization movements, can be realized anglesynchronously. Dynamic changes of the goods to be packed or the
packaging material in the plant (like slippage of the products to be
packed or expansion of the packaging material) can be detected by
sensors while the machine is running and eliminated by modifying
the corresponding drive movements. This development
substantially changes and highly simplifies the classical mechanical
machine concept. The structure of the packaging machine can be
broken down into modules that are easy apply and standardize.
ELAU AG
PacDrive
page 15
PD_SysUebersSCL_us.fm
3 System Overview
Fig. 3-1: Sketch of a packaging machine
page 16
PacDrive
ELAU AG
3.2 Structure of the PacDrive™ Automation System
3.2
Structure of the PacDrive™ Automation System
Hard-copy for correction
The PackDrive™ automation system offers a technically and
economically ideal solution for electronic packaging machines.
PacDrive™ consists of an efficient PC-based control, the PacDrive
Controller and the digital motor controllers, which include the mains
connection unit, the end-stage power and the servo regulator of the
individual axes(Fig. 3-2).
The PacDrive controller is the intelligent head of the system, and is
based on an industrial PC. The PacDrive controller synchronizes
and coordinates the motion functions of the packaging machine.
Using an IEC 61131-3 soft-PLC, the PacDrive Controller ventures
into applications previously reserved to classical PLCs. The
individual PLC or positioning tasks can be broken down into several
parallel tasks, which are implemented with the EPAS-4
programming environment according to IEC 61131-3 standard.
The ring-shaped digital real-time bus SERCOS ensures safe data
exchange with the motor controllers. Even in applications on rotary
tables etc., the distributed motor controllers are reliably supplied
with new set values. All internal states of the axes can be checked
via the real-time bus and processed by the PacDrive controller.
In addition to digital and analog inputs and outputs, the PacDrive
Controller has two serial interfaces and one Ethernet interface. A
variety of process visualization and control systems can be
connected to PacDrive™ via the integrated OPC interface. Further
peripheral components can be connected via field bus interface
modules. The PacDrive Controller can act as field bus master or
slave. The built-in interfaces enable remote diagnosis via telephone
modem or Internet.
Particularly in the beverage sector (bottle cappers, bottle labeling
machines) it is necessary to install servo motors on a rotary table.
The small dimensions of the rotary table require innovative
solutions, as the switching cabinet with the standard products
PacDrive Controller and PacDrive MC-4 can usually not be
mounted on the rotary table. To keep additional wiring to the rotary
table down to a minimum, ELAU developed the PacDrive SCL-055
for such applications - a compact servo motor with integrated motor
controller that is suitable for aseptic closing/sealing machines. The
PacDrive SCL-055 Aseptic has a special surface coating that
makes it resistant against many cleaners and disinfectants.
PD_SysUebersSCL_us.fm
To keep the size of the SCL drives down to a minimum, the power
supply is arranged centrally via the external power supply unit
PacDrive PS-4 in combination with PacDrive PD-8.
ELAU AG
PacDrive
page 17
3 System Overview
Structure
PD_SysUebersSCL_us.fm
3.3
Fig. 3-2: System overview of the PackDrive™ Automation System
page 18
PacDrive
ELAU AG
3.4 Components
Hard-copy for correction
3.4
Components
Automation Toolkit EPAS-4
EPAS-4 has extensive and proven functions and tools. A key
advantage of EPAS-4 is that all components are tuned to each
other.
For you as a user, this means:
Libraries
Quick familiarization, easy handling, all tools integrated.
Extensive libraries, tailored to the target group, help to save costs
and improve the quality of user programs.
Highlights
„ Runs under Windows (Windows XP Professional
recommended)
„ IEC 61131-3 programming languages
„ SCOPE tool (oscilloscope functions)
„ Diagnosing tool
„ Very good debugging features
„ Serial or TCP/IP connection to the PacDrive controller
PacDrive Controller
The PacDrive controller, a Pentium-based control hardware with
the real-time operating system VxWorks, centrally realizes the PLC
and motion functions.
A PacDrive controller synchronizes, coordinates and generates the
positioning functions for the drives of a food and packaging
machine.
PD_SysUebersSCL_us.fm
A variety of standard HMIs are used for HMI tasks. Whether lowcost clear text or IPC - no problem for the flexible PacDrive
Controller.
Highlights
„ Pentium controller hardware
„ Real-time operating system VxWorks
„ IEC 61131 PLC and Motion Control
„ Scalable performance
„ Standard interfaces to low-cost operating units or PC-based HMI
„ Compact book-size form
„ Ethernet interface
„ Standard field buses
„ VarioCam® Motion Control
„ SERCOS drive bus
ELAU AG
PacDrive
page 19
3 System Overview
PacDrive SCL
Motor with The compact size of the PacDrive SCL combines motor and power
integrated electronics in the smallest space. The innovative SCL has the
MotorController motor, the power output level and the digital servo controller for an
axis in one casing, which saves space. Thanks to the compact size
with integrated controller, it is perfectly suited for distributed
installation. It is available with single- or multi-turn encoder and
configures itself with the help of the electronic type plate inside the
SCL.
Highlights
„ Compact size
„ 3.5-fold peak torque
„ Integrated SERCOS interface
„ High-resolution single- or multi-turn encoders
„ IP65 / IP67 protection means
„ Easy wiring
„ High failure proofness
„ Trapezoid shape
„ Aseptic variant IP67 (with positive pressure option)
PacDrive PS-4
Centralized The power supply unit PS-4 is characterized by a compact and
supply autonomous structure for switching cabinet installation plus highly
modern technology. All PacDrive SCLs are served on just one line
via the PacDrive PS-4, which is quick to install. PS-4 thus fits
smoothly into the extremely flexible modular drive concept.
Highlights
„ 1- or 3-phase power supply
„ Integrated mains filter and bleeder
„ 5 kW permanent power / 10 kW peak power
„ DC-circuit power for up to 32 SCL-055s (depending on the
application)
„ Integrated SERCOS interface
„ Full diagnosis facilities thanks to integrated controller
„ Easy installation
Information on further components is available in the operating
manual PacDrive PS-4 and PacDrive PD-8. Information on further
components is available in the Project Manual.
page 20
PacDrive
ELAU AG
PD_SysUebersSCL_us.fm
PacDrive PD-8
Flexible The PacDrive PD-8 power distribution box is the link between PS-4
distributor and SCL. One "distributor" to which 1 to 8 SCL hybrid cables can
be connected, depending on the number of drives. If more than 8
drives are operated, simply extend the system by one or several
PD-8 distributors. Like the SCL, the PacDrive PD-8 is available in
standard and aseptic variants.
Hard-copy for correction
4.1 Transportation
4
Transportation, Storage, Unpacking
4.1
Transportation
Avoid shocks.
Check units for transport damage and immediately inform your
transport company, if necessary.
4.2
Storage
Store the units in a clean, dry place.
Storage conditions:
„
„
4.3
Air temperature between -25°C and +70°C
Temperature fluctuations max. 30 K per hour.
Unpacking
Check whether the consignment is complete.
Check all units for transport damage.
PS-4 type plate
The type plates contain all necessary data:
logistic type plate
!
• ACHTUNG! • ATTENTION! •
• HOCHSPANNUNG!
• ERHÖHTER ABLEITSTROM!
• HOHE TEMPERATUR!
• INSTALLATION!
Vor Arbeiten am Gerät, Netzanschluß trennen. Entladezeit > 2min.
Betrieb nur mit angeschlossenem Schutzleiter.
Oberfläche des Gerätes im Betriebszustand nicht berühren.
Bei Inbetriebnahme, Installationshinweise in der Bedienungsanleitung beachten.
• HIGH VOLTAGE!
• HIGH LEAKAGE CURRENT!
• HIGH TEMPERATURE!
• INSTALLATION!
Disconnect from mains supply, before working on this equipment, Electric discharge> 2min.
Operation only with connected safety ground.
Do not touch this surface under operation conditions.
Read installation instruction before installing.
• HAUTE TENSION!
• COURANT DE FUITE ELEVEE!
• TEMPERATURE ELEVEE!
• INSTALLATION!
Coupez l´alimentation avant de manipuler l´appareil. Temps de décharge > 2min.
Fonctionnement uniquement avec conducteur de protection raccordé.
ne touchez pas la surface de l´appareil en marche.
Respectez le manuel d´instruction lors de la mise en marche.
• ALTA TENSIONE!
• ALTA DISPERSIONE DI CORRENTE!
• ALTA TEMPERATURA!
• INSTALLATIONE!
Disconetttere l`alimentazione prima di lavorare all`apparecchio. Tempo di scarica > 2min.
Operare solo con il conduttore di scarico a terra collegato.
Non toccare la superficie dell`apparecchio in funcione.
Prima della messa in funzione dell`apparecchio consultare il manuale di istruzione
• ALTO VOLTAJE!
• ALTA TENSION!
• ALTA TEMPERATURA!
• INSTALACION!
Desconecten de la red antes de trabajar con este equipo, descarga electrica > 2min.
Operen solo con una conexion a tierra segura.
No toquen esta superficie durante la operacion.
Lean las instrucciones de montaje antes de instalar.
PS-4/10/16/230/00 POWER SUPPLY
Input 1:
Input 2:
1AC / 3AC 220V - 240V 20A 50/60Hz
DC 24V 13A
PD_OpManPS-4_04_us.FM
Output 1: DC 325V 10A / 18A
Output 2: DC 24V 13A
technical type plate
PD_Typenschild_auf_PS4_us.FH8
Fig. 4-1: Type plate on PacDrive PS-4
ELAU AG
PacDrive PS-4 / PD-8
page 21
PS-4/10/16/230/00 POWER SUPPLY
13130258
001000.0010
HW: C00000
SW: 00.14.00
W37
Fig. 4-2: Logistic type plate of a PacDrive PS-4
Article name
PS-4/10/16/230/00 POWER SUPPLY
Input 1:
Input 2:
1AC / 3AC 220V - 240V 20A 50/60Hz
DC 24V 13A
Output 1: DC 325V 10A / 18A
Output 2: DC 24V 13A
Fig. 4-3: Technical type plate of a PacDrive PS-4
PD-8 type plate
sercos out
power out
SCL055 7
SCL055 8
SCL055 5
SCL055 6
Vor Inbetriebnahme, Installationshinweise in der Bedienungsanleitung beachten.
Read installation instruction, before installing.
Respectez le manuel d´instruction lors de la mise en marche.
Prima della messa in funzione del´apparecchio consultare il manuale di istruzione.
Lean las instrucciones de montaje antes de instalar.
SCL055 3
INSTALLATION!
INSTALLATION!
INSTALLATION!
INSTALLATIONE!
INSTALACION!
SCL055 4
SCL055 1
SCL055 2
Made in Germany
PD-8
sercos in
Vor Arbeiten am Gerät, Netzanschluß trennen. Entladezeit > 2min.
Disconnect from mains supply, before working on this equipment. Electric discharge > 2min.
Coupez l´alimentation avant de manipuler l´appareil. Temps de décharge > 2min.
Disconetttere l´alimentatione prima di lavorare all´apparechio. Tempo di sacarica > 2min.
Desconecten de la red antes de trabajar con este equipo. Descarga electrica > 2min.
DC 325V 5A
DC 24V 1A
HOCHSPANNUNG!
HIGH VOLTAGE!
HAUTE TENSION!
ALTA TENSIONE!
ALTO VOLTAJE!
DC 325V 16A
DC 24V 13A
HW: 000
Input 1 / Output 1:
Input 2 / Output 2:
13130259-001
001001.0010 W37
Output SCL:
PD-8/10 POWER DISTRIBUTION STD.
!
power in
technical type plate
PD-8/10 POWER DISTRIBUTION STD.
PacDrive
logistic type plate
Hard-copy for correction
Article name
Made in Germany
4 Transportation, Storage, Unpacking
PD-8_Typenschild_auf_PD8_us.FH8
Article name
PD-8/10 POWER DISTRIBUTION STD.
13130259-001
001001.0010 W37
HW: 000
Made in Germany
Fig. 4-4: Type plate on PD-8
Article name
PD-8/10 POWER DISTRIBUTION STD.
Input 1 / Output 1:
Input 2 / Output 2:
DC 325V 16A
DC 24V 13A
Output SCL:
DC 325V 5A
DC 24V 1A
Fig. 4-6: Technical type plate of a PacDrive PD-8
page 22
PacDrive PS-4 / PD-8
ELAU AG
PD_OpManPS-4_04_us.FM
Fig. 4-5: Logistic type plate of a PacDrive PD-8
4.3 Unpacking
Type plate PD-8 / PD-4 board version
PD-8 POWER DISTRIBUTOR-UNIT
11130166
591078.0030
HW: 200
Y13
Made in Germany
Hard-copy for correction
logistic type plate
PD_Typenschild_PD8_PL_de.FH8
PD_OpManPS-4_04_us.FM
Fig. 4-7: Logistic type plate on the board version of PacDrive PD-8/4
ELAU AG
PacDrive PS-4 / PD-8
page 23
PD_OpManPS-4_04_us.FM
Hard-copy for correction
4 Transportation, Storage, Unpacking
page 24
PacDrive PS-4 / PD-8
ELAU AG
5.1 Spare Parts,
Hard-copy for correction
5
Maintenance
Recognizing and clearing an error quickly helps to keep the related
production loss down to a minimum.
The diagnosis messages of the PacDrive™ system, which can be
checked using the Automation Toolkit EPAS-4, make it possible to
look for errors deliberately and effectively.
In case of an error, defective components can easily be
exchanged. This ensures that the problem can be solved quickly
and operation can be resumed soon. This work must be done by
qualified service staff only.
When returning a defective unit to the ELAU customer service,
please complete the attached error report form.
5.1
Spare Parts, Components
Stock keeping of spare parts:
Keeping a stock of the essential components is a key prerequisite
for the permanent functionality of the equipment.
NOTE
Only devices with identical hardware configuration and software
version may be exchanged. This ensures that the plant will work
correctly after the component change.
When ordering spare parts, please give the following data:
„
„
Article name: e.g. PS-4/10/16/230/00
Article number: e.g. 13 13 02 59-001
NOTE
PD_OpManPS-4_05_us.fm
You can find this information on the type plate of the equipment (see
Fig. 4-1)or in the configuration of the PacDrive™ system.
ELAU AG
PacDrive PS-4 / PD-8
page 25
5 Maintenance
Repair
By all means complete the attached error report form when
returning defective components.
You can also make a photocopy of the error report form and use it
as a fax message.
CAUTION!
Electro static discharge!
Components may be damaged!
„ Return electronic components in original or equivalent
packaging only.
„ Always use ESD packaging/foil.
5.3
Service Addresses
Hard-copy for correction
5.2
For ordering spare parts
ELAU AG
Postfach 1255
D-97821 Marktheidenfeld
Phone:
Fax:
+49 (0) 93 91 / 606 - 0
+49 (0) 93 91 / 606 - 300
Repairs and customer service
Please send the components to be repaired or checked, along with
the error report, to this address:
ELAU AG
Abt. Kundendienst
Postfach 1255
D-97821 Marktheidenfeld
Phone:
Fax:
street address:
Dillberg 12
D-97828 Marktheidenfeld
+49 (0) 93 91 / 606 - 142
+49 (0) 93 91 / 606 - 340
Service team
Should you need to talk to a member of our service team or require
on-site service, please contact:
Phone:
Fax:
page 26
PD_OpManPS-4_05_us.fm
ELAU AG
Abt. Applikation
Postfach 1255
D-97821 Marktheidenfeld
+49 (0) 93 91 / 606 -0
+49 (0) 93 91 / 606 -300
PacDrive PS-4 / PD-8
ELAU AG
5.4 Exchanging units
5.4
Exchanging units
Hard-copy for correction
In addition to the notes below, please observe the information of
the machine producer when exchanging the PacDrive PS-4.
DANGER!
High voltage!
Life hazard!
High voltage possible with servo motors in generator operation!
„ Before working on electrical units, disconnect from mains supply
and lock out.
„ Make sure that the drives are standing still.
„ Do not disconnect connector plugs while they are carrying
voltage.
„ Before working on the unit, discharge the DC-circuit and use a
voltmeter to check that there is no voltage.
CAUTION!
PD_OpManPS-4_05_us.fm
Electro static discharge!
Components may be damaged!
„ Only touch the boards on the edges.
Do not touch any connections or components.
„ Existing static charges can be discharged by touching a
grounded metallic surface, e.g. a grounded equipment casing.
„ Prevent the formation of electrostatic charge by using suitable
clothing, carpets or furniture and by moving the boards as little
as possible.
ELAU AG
PacDrive PS-4 / PD-8
page 27
5 Maintenance
Open main switch.
Lock out main switch.
DANGER!
High voltage!
Life hazard!
„ Disconnect and connect power supply only when the plant is
voltage-free!
CAUTION!
Hot surfaces on the PS-4 casing!
Risk of burns!
„ Wear protective gloves or wait until the surface temperature
permits touching without risk!
Hard-copy for correction
Exchanging the PacDrive PS-4
Disconnect PS-4 from power supply.
Open screws on the top and bottom of the casing.
Remove PacDrive PS-4
Install new PS-4 and tighten the screws.
Connect PS-4 according to the machine wiring diagram.
Restart the plant.
Exchange PacDrive PD-8
Open main switch.
Lock out main switch.
DANGER!
Open the clamp and remove the power in/out cable.
Open the SERCOS in/out connection and remove the cable.
Open the SCL connections and remove the cable.
Exchange the PC-8.
Insert the power in/out cable in the corresponding cable duct, fix
the clamp and fix the strain relief on the cable duct while the
cable is relieved.
page 28
PacDrive PS-4 / PD-8
ELAU AG
PD_OpManPS-4_05_us.fm
High voltage!
Life hazard!
„ Disconnect and connect power supply only when the plant is
voltage-free!
5.5 Cleaning
Hard-copy for correction
Insert the SERCOS in/out cable in the corresponding cable duct,
snap the connector into the outlet and fix the strain relief on the
cable duct while the cable is relieved.
Insert the SCL connections in the corresponding cable duct,
snap the connector into the outlet and fix the strain relief on the
cable duct while the cable is relieved.
Exchanging cables
Open main switch.
Lock out main switch.
DANGER!
High voltage!
Life hazard!
„ Disconnect and connect power supply only when the plant is
voltage-free!
„ Do not insert the connectors unless both sides are dry and
clean!
„ If no ready made ELAU cables are used, make sure the
assignment of the new cables matches the wiring diagram of the
machine manufacturer!
Remove cables from the PS-4 / fix them back (see Exchanging
PacDrive PS-4).
Remove cables from the PD-8 / fix them back (see Exchanging
PacDrive PD-8).
When exchanging cables, also observe the instructions of the
machine manufacturer.
5.5
Cleaning
If installed as directed, the units are to a large extent maintenancefree.
PD_OpManPS-4_05_us.fm
To remove dust and foreign objects brought in by the cooling air
flow, disconnect the units from the power supply, remove them and
use dry compressed air (max. 1 bar) to blow away the pollution.
ELAU AG
PacDrive PS-4 / PD-8
page 29
5 Maintenance
EMC Rules
To control and regulate motors, the mains voltage is stored in the
DC-circuit of the PS-4 by means of rectification. This DC-circuit
voltage supplies all connected SCL-055s. In the SCL-055, this
stored energy is fed to the motor by deliberately activating and
deactivating six semiconductor switches. The steep rise and fall of
the voltage puts high demands on the insulation strength of the
motor winding. Another essential aspect to be considered is Electro
Magnetic Compatibility (EMC) with other system components. The
flank steepness of the clocked voltage generates harmonic
oscillation of great intensity, up into the high-frequency range.
Therefore observe the following EMC rules:
„
„
„
„
„
„
PD_OpManPS-4_05_us.fm
„
Choose the grounding option with the lowest possible ohm rate
for the PS-4 (e.g. unpainted mounting board of switching
cabinet) for installation.
Contact the largest possible surface (skin effect). If necessary,
remove existing paint to achieve large-surface contact.
From the Central Earthing Point, lay the grounding wires to the
respective connections in a star structure. Earthing loops are not
allowed and can cause unnecessary distortions.
Use shielded cables only.
Only large-surface shield transitions are allowed.
By all means observe the switching proposals.
Do not lay any cable loops inside the switching cabinet.
Hard-copy for correction
5.6
page 30
PacDrive PS-4 / PD-8
ELAU AG
5.7 Commissioning
CAUTION!
Hard-copy for correction
Electromagnetic fields!
Disturbances or failure of the system possible!
The rules described below must be observed for installation, in
order to rule out the consequences of excessive disturbance effects
as far as possible.
„ In correlation with electronic controls, no inductive loads must be
switched without suitable interference elimination.
„ For DC operation, suitable interference elimination can be
achieved by arranging recovery diodes. For AC operation,
commercially available erasing elements matching the
connector type can be used.
„ Only the interference elimination element mounted immediately
at the point of inductivity serves its purpose. Otherwise, the
switching pulse may even emit increased interference via the
interference elimination elements. It is much easier to avoid
sources of interference in the first place, than to eliminate the
effects of existing interference.
„ In no case must the contacts switching unerased inductive loads
be arranged in the same room as the PacDrive™ components.
The same goes for cables carrying unerased, switched
inductivity and cables running parallel to them. The controller
must be separated from such "disturbers" by a Faraday cage
(own section in the switching cabinet).
5.7
Commissioning
We urgently recommend that you use ELAU staff for
commissioning.
You should do so not only for warranty reasons. At the same time
„ the equipment is checked,
„ the optimum configuration is determined,
„ and the operating staff are instructed.
DANGER!
PD_OpManPS-4_05_us.fm
High leakage current!
Life hazard!
„ The leakage current is greater than 3.5 mA. Therefore the units
must have a firm connection to the power grid (according to DIN
EN 50178 - equipment of high-voltage systems).
ELAU AG
PacDrive PS-4 / PD-8
page 31
Commissioning procedure:
Unpacking and Remove packaging.
checking
Make sure the units are not damaged. Only undamaged units
should be put into operation.
Check if the consignment is complete.
Check the data with the help of the type plate.
See also "Unpacking" on page 21.
See also "Exchanging units" on page 27.
Setting the Set the intended SERCOS address (0-99) with a suitable tool.
SERCOS
address
NOTE
Make sure no address is used twice in a SERCOS ring! Each
SERCOS slave needs its own, unambiguous SERCOS address.
Installation
Observe the requirements for the place in which the equipment
may be used.
Observe the requirements for protection and EMC rules.
Hard-copy for correction
5 Maintenance
CAUTION!
PacDrive PS-4 has a rated connection voltage of 230 V!
Incorrect connection voltage may result in the destruction of the
device!
„ When using the devi8ce in rotary current networks (3 AC 380...480
V), use an autotransformer to avoid a destruction of the PS-4.
Mount the device.
PS-4 Front
power supply
connection, 3 phase
X1
Q2
! 230V !
K1
autotransformer optional;
required, if UNetz = 230 V
0V
PE
DC+
DC-
3
4
5
1
5/6
X3
2
7/8
3
1
4
2
5
1
1
S1
9
23
S2
SERCOS
address switch
tens digit
units digit
X5
LWL in
X6
LWL out
2
3
4
X4
24V
0V
PE
DC+
DC-
23
6
DC+
DC+
DCDC-
connecting cable PS-4/PD-8
24V
2
0
5
1
456
4
X2
1
2
X8
SERCOS
3
4
5
PD_Inb_PS-4_1_us.fh8
Fig. 5-1: Assignment for connections to PS-4
page 32
PacDrive PS-4 / PD-8
ELAU AG
PD_OpManPS-4_05_us.fm
3
+24V
0V
PE
L1
L2
L3
8
0
2
4
1
1
6
7
9
Q1
RDY+
RDY NC
NC
5
2
3
456
3~
24V=
1
78
HW enable
0V
ZK dis
0V
78
L1 L2 L3 PE
5.7 Commissioning
Hard-copy for correction
Electrical
connections of
PS-4
Make connections for X1 and X2 according to the wiring
diagram. (Wiring examples: See also "Electrical connections" on
page 53.)
Connect the prefabricated cable (PS-4/PD-8) with X4.
Insert the prefabricated SERCOS cable into X8 and snap it on.
PD-8
SERCOS in
Power in
SERCOS out
SCL 1 SCL 2
DC+ DC- PE
SCL 3 SCL 4 SCL 5 SCL 6
SCL 7 SCL 8
24V 0V
24V 0V
connecting cable PS-4/PD-8
0V
0V
24V
24V
PE
DC-
7/8
5/6
2
1
Power out
DC+ DC- PE
to next PD-8
DC+
all shields
PD_Inb_PD-8_1_us.fh8
Fig. 5-2: Assignment for connections to PD-8
Electrical
connections of
PD-8
Remove the blind plugs ("power in" and SECOS in) from the
cable ducts on the PD-8.
SERCOS in SCL055 (1) SCL055 (3)
Power in SCL055 (2) SCL055 (4)
SCL055 (5) SCL055 (7) SERCOS out
SCL055 (6) SCL055 (8) Power out
PD-8_Ansch.fh8
Fig. 5-3: PD-8 cable ducts
PD_OpManPS-4_05_us.fm
Insert the PS-4/PD-8 connection cables in the "power in"
opening.
Insert the SECOS cable in the opening "SERCOS in".
ELAU AG
PacDrive PS-4 / PD-8
page 33
5 Maintenance
jumper for termination
fuse
SERCOS cable
cap nut
cable duct
SERCOS connection (SCL)
dummy plug
SCL_Ansch_us.fh8
Hard-copy for correction
power supply connection
Fig. 5-4: Wire the PS-4/
connection cable PS-4/PD-8 and fix the strain relief on the cable
duct while the cable is relieved.
Insert the prefabricated SERCOS cable into the outlet and snap
it on. Fix the strain relief on the cable duct while the cable is
relieved.
If more PD-8s are connected, connect prefabricated "PD-8/PD8" connection cable with the power in/out connections and the
next SERCOS cable with SERCOS in/out as described above.
CAUTION!
Penetrating liquid due to inexpert installation of cable ducts or
missing blind plugs!
Damage to electrical parts!
„ Check if the cable ducts are tight.
„ Immediately replace missing or defective blind plugs on unused
cable ducts. Do not run the PD-8 without having fixed the blind
plugs and checked if they are tight.
„ Do not run the PD-8 while the cover is open. Before starting the
plant, close the cover and check if it is tight.
PD_OpManPS-4_05_us.fm
See also "Technical Data" on page 47.
page 34
PacDrive PS-4 / PD-8
ELAU AG
5.8 Configuration /
Hard-copy for correction
NOTE
The two jumpers must be placed in "closed" position over the
SERCOS connector only at the connection of the last PacDrive
SCL-055, even if several PD-8s are used. This closes the SERCOS
ring.
The physical order of the SERCOS slaves is different from the
numbers on the PD-8 cable ducts.
Check safety functions such as the EMERGENCY OFF switch.
Continue the plant according to the operating manual of the packaging
commissioning.
machine producer.
Information on the connection of the PacDrive SCL to the PacDrive
PD-8 is available in the "PacDrive SCL" operating manual. Further
information on the slaves in the SERCOS ring and system solutions
with air barriers can also be found in the "PacDrive SCL" operating
manual.
5.7.1
Slaves in the SERCOS ring
Removing a single PacDrive SCL from the SERCOS ring
For test purposes, single PacDrive SCLs can be removed from the
SERCOS ring during commissioning or when exchanging units.
Proceed as follows:
Remove the connector of the corresponding SCL.
Insert a SERCOS jumper (Art. no. 53150032) in the free place.
9 The SCL in the SERCOS ring has now been substituted.
Fig. 5-5: SERCOS jumper as SCL substitute
5.8
Configuration / Programming / Diagnosis
The PacDrive PS-4 is matched by ELAU. The customer needs not
match them.
PD_OpManPS-4_05_us.fm
Error diagnosis and monitoring of operating states are done in the
PacDrive controllers. For information, consult the corresponding
manuals.
In addition, diagnosis is possible by means of the LEDs on the
PacDrive PS-4.
ELAU AG
PacDrive PS-4 / PD-8
page 35
5 Maintenance
C
US
LISTED
i/o
!
X1
Instructions see cover side!
(INDUSTRIAL
CONTROL
EQUIPMENT)
72KL
reset
24V/in
pow
err
S1
ac-power
S2
buserr
X2
dc-bus
+
+
X3 -
reset
reset button
control voltage indicator
pow
err
S1
S2
address adjustment
SERCOS
S1 tens digit
S2 units digit
buserr
X6
S3
SERCOS - bus error indicator
sercos
X7
SCL-servodrive
error indicator
X5
diag
230 Volt !
Hard-copy for correction
Diagnosis LEDs
PS-4
5.8.1
X8
X4
Made in Germany
PD_Diagnose_PS-4_LED_us.fh8
Fig. 5-6: Diagnosis LEDs of the PacDrive PS-4
reset
pow
Button to reset the PacDrive PS-4. Only the PacDrive PS-4 is
restarted.
Green control voltage indicator
Off: Control voltage (24 V) missing or too low
On: Normal operation; control voltage in normal range
Red error LED (indicated by the PacDrive system)
PD_OpManPS-4_05_us.fm
err
page 36
PacDrive PS-4 / PD-8
ELAU AG
5.8 Configuration /
Hard-copy for correction
The error indicator signals the operating state of the PacDrive PS-4
based on the following states:
LED permanent off: no error
n
f
t in sec
LED fast flash: general error
n
f
0
0.26
0.51
1.02
2.05
t in sec
1.02
2.05
t in sec
LED slow flash: SERCOS error
n
f
0
LED permanent on: fatal system error
n
f
Diagnose LED PS4 us fh8
t in sec
Fig. 5-7: Display state of diagnosis LED "err"
S1/S2
address setting rotary switch
The double-digit SERCOS (00 - 99) must be unabmiguous for each
SERCOS slave.
S1: Tens digit of the SERCOS address
S2: Ones digit of the SERCOS address
buserr
SERCOS bus error indicator (signalled from SERCOS bus)
Display that shows errors of the SERCOS bus. It is on, if a bus
error occurs. This state can also occur for a short time and cannot
be quitted.
5.8.2
Combination of PacDrive SCL and PacDrive PS-4
SCL signals in the m PS-4
PD_OpManPS-4_05_us.fm
All Ready signals of the individual PacDrive SCLs come together in
the PS-4, where they are evaluated. The Ready contact on the PS4 is not set until all SCLs and the PS-4 supply a Ready signal.
ELAU AG
PacDrive PS-4 / PD-8
page 37
5 Maintenance
There is no HardwareEnable input on the SCL. However, the input
HardwareEnable, the signal PowerSupplyEnable and error
messages of the PS-4 have to lead to reactions in the SCL.
Therefore the following signals are sent from the PacDrive PS-4 to
the MAx-4:
„ PS-4 is active
„ Class 1 error message from PS-4
„ Error message with error reaction A from PS-4.
The ramping-down of the motor (error reaction B) is initiated in the
SCL if the PS-4 is reported to be inactive or an error message with
error reaction B is reported from the PS-4.
In case of error messages with error reaction A from the PS-4, the
final stages of the corresponding SCL are switched off immediately.
The motor coasts to a stop. The SCL behaves like an MC-4 on
which CoastEnable is set and HardwareEnable is deactivated. No
error message is triggered.
Hard-copy for correction
Influence of the PS-4 signals on the SCL
NOTE
The function "InverterEnable" is not integrated in the PacDrive PS-4.
A safety connection has to be implemented by means of a RDY
contact.
5.9
Order numbers
5.9.1
PacDrive PS-4
type key
PS-4 / 10 / 16 / 230 / 00
series
10
power range
16 A
mains voltage
230 V
options
00 = none
Order number
13 13 02 58
Article name
Explanations
PacDrive PS-4
Table 5-1: Order numbers for PacDrive PS-4
page 38
PacDrive PS-4 / PD-8
ELAU AG
PD_OpManPS-4_05_us.fm
Fig. 5-8: Type key legend of the PacDrive PS-4
5.9 Order numbers
PacDrive PD-8
Hard-copy for correction
Order number
Article name
Explanations
13 13 02 59 - 001
PacDrive PD-8
Plastic (standard)
13 13 02 59 - 002
PacDrive PD-8
Stainless steel
11 13 01 66
PD-8 unit
Curcuit board version
11 13 01 67
PD-4 power distributor
Curcuit board version
Table 5-2: Order numbers for PacDrive PD-8 / PD-4
5.9.2
Cables
Connection cables
Order number
Article name
Explanations
15 15 45 02 - XXX E-MO 102
Connection cable PS-4/PD-8
max. 20 m total length from PS-4
to last PD-8
15 15 45 04 - XXX E-MO 104
Connection cable PD-8/PD-8
max. 20 m total length from PS-4
to last PD-8
15 15 45 11-XXX
E-MO 109
Connection cable PS-4/PD-8,
aseptic
max. 20 m total length from PS-4
to last PD-8
15 15 45 12-XXX
E-MO 110
Connection cable PD-8/PD-8,
aseptic
max. 20 m total length from PS-4
to last PD-8
*) cable lengths up to 2 m in steps of 10 cm
cable lengths up to 10 m in steps of 50 cm
Fig. 5-9: Order numbers for connection cables
CAUTION!
Bending radius for ELAU hybrid cables:
„ for fixed installation, 3 x cable diameter!
„ for permanent motion, 10 x cable diameter!
Cables may be damaged!
„ Observe the defined bending radius.
SERCOS cables
PD_OpManPS-4_05_us.fm
Order number
Article name
Explanations
KA 99 037 - 005
Patch cable category 7
RJ45 patch cable (Cat 7 / 0.5 m)
KA 99 037 - 010
Patch cable category 7
RJ45 patch cable (Cat 7 / 1 m)
KA 99 037 - 020
Patch cable category 7
RJ45 patch cable (Cat 7 / 2m)
Table 5-3: Order numbers for SERCOS cables
ELAU AG
PacDrive PS-4 / PD-8
page 39
PD_OpManPS-4_05_us.fm
Hard-copy for correction
5 Maintenance
page 40
PacDrive PS-4 / PD-8
ELAU AG
Hard-copy for correction
6.1 Creation of a PacDrive PS-4/PD-8, SCL055 application
6
Project definition
6.1
Creation of a PacDrive PS-4/PD-8, SCL055 application
In addition to their use in normal industrial environments, the units
PacDrive PD-8 and PacDrive SCL-055 are also designed for
aseptic applications. Aseptic applications have special
requirements regarding the surface quality of devices and cables.
The figure below shows a PacDrive PS-4, PD-8, SCL-055
combination with an outline of possible fields of application.
Range of
applications
3)
PacDrive
PS-4
2)
collector ring
(optional)
Exp.
1), 2) E-MO-102
3) E-MO-109
PacDrive
PD-8
PacDrive
SCL
Exp.
1) E-MO-101
2), 3) E-MO-105
1), 2), 3) KA 99 037-XXX
Exp. 1), 2) E-MO-104
3) E-MO-110
1) Standard environment
2) SCL in aseptic environment
3) SCL and PD-8 in aseptic environmnet
1), 2), 3) KA 99 037-XXX
to further PD-8
PD_Inb_Schalt_Übersicht.fh8
Fig. 6-1: Overview of applications
6.2
PacDrive PS-4
6.2.1
Mains Connection of PacDrive PS-4
Switching on
When the mains voltage is switched on, the DC-circuit capacitors in
the PacDrive PS-4 are "gently" charged via the built-in bleeder
resistor. The minimum time between to precharge procedures is 15 s.
Grounding conditions of the mains network
Grounded PacDrive PS-4s can be operated without potential separation on
rotary rotary current networks with grounded star point.
current
networks
PD_OpManPS-4_06_us.fm
ungrounded
rotary current
networks
ELAU AG
In ungrounded networks (IT networks) or networks that are not
grounded in the star point, there is an increased risk of
impermissible excess voltages between the outer conductors and
the casing of the PacDrive servo amplifier.
For operations in such networks, we therefore prescribe a
separating transformer with a grounded star point on the output
side and a grounded PE connection of the PacDrive PS-4.
PacDrive PS-4 / PD-8
page 41
6 Project definition
If the mains voltage is outside the range indicated in the technical
data, a transformer is required to adjust it to the power intake of the
plant.
In star point grounded networks, the voltage is adjusted by means
of an autotransformer.
In all other networks, a separating transformer is required.
CAUTION!
PacDrive PS-4 has a rated connection voltage of 230 V!
Incorrect connection voltage may result in the destruction of the
device!
„ For wiring and installation, make sure that the DC-bus of
PacDrive MC-4 units with a rated connection voltage of 400 V is
not coupled with a PacDrive PS-4 unit with a rated voltage of
230 V.
„ When using the unit in rotary current networks (3 AC 380...480
V), use a transformer to prevent the destruction of the
PS-4.
Hard-copy for correction
Adjustment of the Mains Voltage
Wiring examples
The PacDrive PS-4 can be directly connected to grounded rotary
current networks with 3 x AC 230 V, +/- 10%. For lower
requirements, a single-phase power connection 1 x AC 230 V is
possible.
PS-4 Front
L2'
L3
L3'
PE PE'
5
Q1
4
1
23
9
1
3
S1
S2
23
0
L2
4
2
456
L1'
1
0
L1
X2
456
2
+24V
0V
PE
L1
L2
L3
9
1
78
L1 L2 L3 PE
78
direct 3 phase power connection (230 V)
X5
5
6
K1
power choke
PS-4 Front
N'
5
Q1
K1
4
5
1
23
9
1
3
S1
S2
23
0
N
PE PE'
4
2
456
L'
1
0
L
+24V
0V
PE
L1
L2
L3
456
2
9
1
X2
78
L N PE
78
direct 1 phase power connection (230 V)
X5
6
power choke
PD_OpManPS-4_06_us.fm
PD_Inb_Schalt_2.fh8
Fig. 6-2: Wiring examples for direct mains connection
page 42
PacDrive PS-4 / PD-8
ELAU AG
3 phase power connection with autotransformer (e.g. 3AC 400V)
PS-4 Front
L1 L2 L3 PE
X2
Q1
4
1
23
9
23
1
3
S1
S2
9
2
0
5
1
456
4
+24V
0V
PE
L1
L2
L3
78
3
0
2
78
1
3~
24V=
456
X5
5
6
K1
1 phase power connection with (UNetz ¹ 230 V)
3
K1
Q2
3
4
23
1
S1
S2
23
0
5
6
2
456
4
1
9
24V=
X2
+24V
0V
PE
L1
L2
L3
0
2
1
1
9
Q1
~
PS-4 Front
78
L N PE
78
Q2
456
Hard-copy for correction
6.2 PacDrive PS-4
X5
5
6
PD_Inb_Schalt_1.fh8
Fig. 6-3: Wiring examples for connection via autotransformer
Protection circuit
24 V
X1
5
6
7
8
RDY+
RDY NC
NC
5
K1
X1
1
6
2
7
8
3
4
1
S1
ON
2
ZK dis
0V
3
4
1
2
Power
K1
3
4
HW enable
0V
ZK dis
0V
PS-4 Front
X1
1
5
2
6
3
7
4
8
RDY+
RDY NC
NC
L0
optional: is used, if a active discharge of the intermediate
circuit is wanted after disconnecting
can also be wired up on 24 V or be
integrated in the emergency stop chain
PD_Inb_Schalt_3.fh8
PD_OpManPS-4_06_us.fm
Fig. 6-4: Wiring examples for mains contactor connection
ELAU AG
PacDrive PS-4 / PD-8
page 43
6 Project definition
Transformer dimensioning
The following formula can be used for the power of the DC-circuit:
2⋅π
P ZK = M eff ⋅ n Mittel ⋅ ---------- ⋅ k ⋅ a ⋅ g
60
PDC = DC-circuit power in W
MEFF = effective torque in Nm
naverage = average torque in min-1
k = factor for motor and controller efficiency = 1.25
a = number of PacDrive SCL’s
g = percentage of PacDrive SCL’s simultaneously in
control (min 0.2 ...1)
The transformer connection power is calculated as follows:
Hard-copy for correction
6.2.2
S AT = P ZK ⋅ F
SAT = transformer connection power in W
PDC = DC-circuit power in W
F = factor for connection power = 2
Calculation of phase currents on the mains side:
Single-phase connection:
S AT
I TS = ------------230V
Three-phase connection:
S AT
I TS = ------------------------230V ⋅ 3
ITS = transformer secondary phase current in A
SAT = transformer connection power in VA
If motion developments and mechanical ambient conditions can only
be determined insufficiently or not at all, the transformer or choke
should be dimensioned for the permanent current of the PacDrive
PS-4. A measurement on the machine can supply the actual mains
burden and thus the necessary performance sizes.
page 44
PacDrive PS-4 / PD-8
ELAU AG
PD_OpManPS-4_06_us.fm
With the detected current value, an autotransformer can be selected
from the table below.
6.2 PacDrive PS-4
Hard-copy for correction
In addition, you can use the tool ECAM-4 version V2.3 or higher for
the calculation. This makes it possible to take almost any possible
combination into account.
Selection table for autotransformers by Block (third-party products)
Type
DSP 400/1,5 DSP 400/3
Output current
3 x 1.5 A
DSP 400/6 DSP 400/9 DSP 400/15
3x3A
3x6A
3x9A
3 x 15 A
Table 6-1: Selection table for autotransformers
If no transformer is used, you have to select and used a mains
choke from the following table:
Order number
Article name
Permanent
current
FI 078 80
NKD 10 / 2.93
10 A
FI 078 74
NKD 25 / 1.17
25 A
PD_OpManPS-4_06_us.fm
Table 6-2: Selection table for mains chokes
ELAU AG
PacDrive PS-4 / PD-8
page 45
6 Project definition
Electricity Supply via Slip Ring
For applications where the PacDrive PD-8 and PacDrive SCL-055
are installed on a turning machine rack (rotary), it is possible to use
a slip ring to supply electricity to the components on the rotary rack.
The following connection proposal shows the connection plan for
the power cable and data cable.
Power cable KA90017
DC+
DCPE
1
DC+
1
DC+
2
DC-
2
DC-
PE
PE
24V
5
24V
6
24V
7
0V
8
0V
24V
5
24V
6
0V
0V
7
0V
8
shield
slip ring
500V/20A
Data cable
Tx+
ws
Tx+
ws
Tx+
Tx-
or
Tx-
or
Tx-
Rx+
ws
Rx+
ws
Rx+
Rx-
gn
Rx-
gn
Rx-
Hard-copy for correction
6.3
shield
shield
Cat.7 patch cable with RJ-45
slip ring
30V/1A
Cat.7 patch cable with RJ-45
NOTE:
Not needed wires stay open!
Between the power connection (DC+ / DC-) and all the other cables, a
"safe disconnection" according to EN50178 must be observed.
PD_Inb_Schleifring_de.fh8
Fig. 6-5: Connection proposal for slip ring transmission
The colors above can be different in practice, as they are not
standardized.
For the Tx and Rx lines, use the respective pairs of leads in the
Cat7 cable.
PD_OpManPS-4_06_us.fm
Pairs that belong together can be identified by their twisting and
common shielding.
page 46
PacDrive PS-4 / PD-8
ELAU AG
Hard-copy for correction
7.1 PacDrive PS-4
7
Technical Data
7.1
PacDrive PS-4
7.1.1
General
PacDrive PS-4/10/16/230
Parameter
Article name
PS-4 / 10 / 16 / 230
Order number
13 13 02 58
Supply
- rated connected voltage
- mains frequency
- control voltage/current
rotary current
3 AC / 1 AC 220V (-10%) to 240V (+10%)
48 .. 62 Hz
DC 24 V (-15%..+25%) / max 13 A
own consumption max. 1 A
DC-circuit
- DC-circuit voltage
- capacity
- UBleeder ON
- UBleeder OFF
- excess voltage
- bleeder resistance
- bleeder - permanent power
- bleeder - peak power
Motor connection
- DC-circuit voltage
- DC-circuit permanent current
DC 270 V to 370 V
660 µF (SCL cap.)
DC 410 V
DC 400 V
DC 430 V
21.5 Ohm
100 W
7 kW
- DC-circuit peak current (1s)
- control voltage
- permanent current
- peak current (1s)
DC 270 V to 370 V
16 A (for supply with 3 AC...)
10 A (for supply with 1 AC...)
32 A
DC 24V (like input voltage)
13 A
25 A
Stray power
- electronic supply
- bleeder (internal)
- power part
approx. 12 W
0 ... 100 W (depending on the application)
approx. 4 W / A
Inputs
- input voltage/current
- input filter:
DC 20..30V / 5 mA
5 ms
Outputs
- relay outputs
DC 20..30 V / 2 A
Weight
3.5 kg
Ventilation
internal fan
Ambient conditions
- protection means
- ambient temperature during
operation
- for storage and transport
- insulation
PD_OpManPS-4_07_us.fm
Value
- excess voltage category
- excess voltage resistance
- degree of radio interference
Approvals
IP20
+5 .. +45 °C (+55 °C with reduced power 2% per K at INC and ISC)
-25 .. +70 °C
degree of pollution 2 ..., no dewing allowed
K III, T2 (DIN VDE 0110)
class 1 (DIN VDE 0160)
class A EN 55011 / EN 61800 - 3
in preparation
Table 7-1: Technical data PacDrive PS-4 /10/16/230
ELAU AG
PacDrive PS-4 / PD-8
page 47
7 Technical Data
In case of ambient temperatures >45 °C, ensure additional
circulation of the cooling air in the switching cabinet (external fan).
C
US
LISTED
X1
Instructions see cover side!
(INDUSTRIAL
CONTROL
EQUIPMENT)
72KL
!
i/o
control signals X1
PS-4
Electrical connections
PacDrive
7.1.2
Hard-copy for correction
NOTE
24V/in
mains connection X2
ac-power
reset
control voltage X2
pow
err
S1
S2
buserr
X2
PD-8/SCL connection X4
X6
S3
X5 LWL IN *)
SERCOS
X6 LWL OUT *)
X7
X7 diagnosis
X8 SERCOS connection
diag
dc-bus
+
+
X3 -
SCL-servodrive
intermediate circuit X3
X5
sercos
230 Volt !
X8
X4
Made in Germany
shield connection
*) stud torque
max. 0,8 Nm
PD_Anschlussübersicht_PS-4_us.fh8
PD_OpManPS-4_07_us.fm
Fig. 7-1: Overview of the connections of the PacDrive PS-4
page 48
PacDrive PS-4 / PD-8
ELAU AG
7.1 PacDrive PS-4
Hard-copy for correction
X1 - Control signals
1
5
Pin Designation
4
8
Meaning
Hardware enable
Range
DC24V (pursuant to
IEC61131-2 type I)
max. cross
section
1.5 mm2
1
HW enable
2
0V
3
DC dis
4
0V
5 *)
RDY +
Ready contact (opens DC 20...30 V / 2 A
in case of an error)
1.5 mm2
6 *)
RDY -
Ready contact
1.5 mm2
7
NC
not connected
1.5 mm2
8
NC
not connected
1.5 mm2
1.5 mm2
DC-circuit discharge
DC24V (pursuant to
IEC61131-2 type I)
1.5 mm2
1.5 mm2
DC 20...30 V / 2 A
*) The Ready contact indicates that the PS-4 and the connected components are
ready for operation. If the Ready contact is closed, the system is ready for
mains connection. In case of an error, the Ready contact opens.
The ready contact has to be included in the mains contactor control, so that the
mains is switched off in case of an error.
Table 7-2: Connection X1 - control signals
X2 - Control Voltage and Mains Connection
+24V
0V
Pin Designation
Meaning
Range
max.
cross
section
PE
1
24 V
24 V control voltage
L1
2
0V
0 V control voltage
4 mm2
L2
3
PE
Protective conductor
connection
4 mm2
4
L1
Phase L1
3AC/1AC 220..240 V 4 mm2
5
L2
Phase L2
3AC/1AC 220..240 V 4 mm2
6
L3
Phase L3
3AC/1AC 220..240 V 4 mm2
L3
-15%..+25%
4 mm2
PD_OpManPS-4_07_us.fm
Table 7-3: Connection X2 - control voltage and mains connection
ELAU AG
PacDrive PS-4 / PD-8
page 49
7 Technical Data
DC+
DC+
DCDC-
Pin
Designation
Meaning
Range
max. cross
section
1
DC+
DC-circuit +
DC 270..370 V 4 mm2
2
DC +
DC-circuit +
DC 270..370 V 4 mm2
3
DC -
DC-circuit -
DC 270..370 V 4 mm2
4
DC -
DC-circuit -
DC 270..370 V 4 mm2
Table 7-4: Connection X3 - DC-circuit
CAUTION!
PacDrive PS-4 has a rated connection voltage of 230 V!
Wrong connection voltage can destroy the unit!
For wiring and installation, make sure that the DC-bus of PacDrive
MC-4 units with a rated connection voltage of 400 V is not coupled
with a PacDrive PS-4 unit with a rated voltage of 230 V.
Hard-copy for correction
X3 - DC-Circuit
X4 PD-8 / SCL Connection
24V
Pin
Designation
Meaning
Range
0V
PE
DC+
4 mm2
1
24 V
24 V control voltage
2
0V
0 V control voltage
4 mm2
3
PE
Protective conductor
connection
4 mm2
4
DC +
DC-circuit +
DC 270..370 V 4 mm2
5
DC -
DC-circuit -
DC 270..370 V 4 mm2
DC-
-15%..+25%
max. cross
section
Table 7-5: Connection X4 PD-8 / SCL connection
X7 - Diagnosis
Designation
Meaning
Range
max. cross
section
0.25 mm2
1
PRO_SEL
2
RxD
receive data
0.25 mm2
3
TxD
transmit data
0.25 mm2
4
GND
signal ground
0.25 mm2
5
RS232_SEL
0.25 mm2
6
VCC
0.25 mm2
Table 7-6: Connection X7 - diagnosis
page 50
PacDrive PS-4 / PD-8
ELAU AG
PD_OpManPS-4_07_us.fm
Pin
7.1 PacDrive PS-4
X8 - SERCOS
Hard-copy for correction
1
8
Pin
Designatio
n
1
SEROUT+
SERCOS Out +
2
SEROUT-
SERCOS Out -
3
SERIN+
SERCOS In +
4
NC
not connected
5
NC
not connected
6
SERIN-
SERCOS In -
7
NC
not connected
8
NC
not connected
Meaning
max.
cross
section
Range
Table 7-7: Connection X8 - SERCOS connection
7.1.3
Dimensions
view from front
view from side
34,5
7
34,5
PS-4
25,5
Ø6,5
US
C
LISTED
i/o
!
reset
• ACHTUNG! • ATTENTION! •
Coupez l´alimentation avant de manipuler l´appareil. Temps de décharge > 2min.
Fonctionnement uniquement avec conducteur de protection raccordé.
ne touchez pas la surface de l´appareil en marche.
Respectez le manuel d´instruction lors de la mise en marche.
• ALTA TENSIONE!
• ALTA DISPERSIONE DI CORRENTE!
• ALTA TEMPERATURA!
• INSTALLATIONE!
Disconetttere l`alimentazione prima di lavorare all`apparecchio. Tempo di scarica > 2min.
Operare solo con il conduttore di scarico a terra collegato.
Non toccare la superficie dell`apparecchio in funcione.
Prima della messa in funzione dell`apparecchio consultare il manuale di istruzione
• ALTO VOLTAJE!
• ALTA TENSION!
• ALTA TEMPERATURA!
• INSTALACION!
Desconecten de la red antes de trabajar con este equipo, descarga electrica > 2min.
Operen solo con una conexion a tierra segura.
No toquen esta superficie durante la operacion.
Lean las instrucciones de montaje antes de instalar.
S1
S2
buserr
X2
X5
230 Volt !
+
+
X3 -
X6
S3
diag
• HAUTE TENSION!
• COURANT DE FUITE ELEVEE!
• TEMPERATURE ELEVEE!
• INSTALLATION!
24V/in
Disconnect from mains supply, before working on this equipment, Electric discharge> 2min.
Operation only with connected safety ground.
Do not touch this surface under operation conditions.
Read installation instruction before installing.
ac-power
• HIGH VOLTAGE!
• HIGH LEAKAGE CURRENT!
• HIGH TEMPERATURE!
• INSTALLATION!
pow
err
dc-bus
Vor Arbeiten am Gerät, Netzanschluß trennen. Entladezeit > 2min.
Betrieb nur mit angeschlossenem Schutzleiter.
Oberfläche des Gerätes im Betriebszustand nicht berühren.
Bei Inbetriebnahme, Installationshinweise in der Bedienungsanleitung beachten.
296
• HOCHSPANNUNG!
• ERHÖHTER ABLEITSTROM!
• HOHE TEMPERATUR!
• INSTALLATION!
240
310
!
X1
Instructions see cover side!
(INDUSTRIAL
CONTROL
EQUIPMENT)
72KL
SCL-servodrive
sercos
X7
X8
X4
PD_OpManPS-4_07_us.fm
240 max. depth incl. connectors!
70
7
44,5
Made in Germany
60
69
PD_Ansicht_PS-4_2407.fh8
Fig. 7-2: Connections of the PacDrive PS-4
ELAU AG
PacDrive PS-4 / PD-8
page 51
7.2
PacDrive PD-8
7.2.1
General
Parameter
Value
Article name
PacDrive PD-8
Order number
13 13 02 59 - 001/002
Supply
- DC-circuit voltage/current
- control voltage/current
DC 270V..370V / 16 A
DC 24 V (-15%..+25%) / max 13 A
Power supply SCL
DC-circuit permanent current
5A
Control voltage SCL
- permanent current (24V)
1A
Weight
0.86 kg
Ventilation
natural convection
Ambient conditions
- protection means
- ambient temperature during
operation
- for storage and transport
- insulation
- excess voltage category
- excess voltage resistance
- degree of radio interference
Hard-copy for correction
7 Technical Data
IP65
+5 .. +55 °C
-25 .. +70 °C
degree of pollution 2 ..., no bedewing
allowed
K III, T2 (DIN VDE 0110)
class 1 (DIN VDE 0160)
class A EN 55011 / EN 61800 - 3
Approvals
PD_OpManPS-4_07_us.fm
Table 7-8: Technical data for PacDrive PD-8
page 52
PacDrive PS-4 / PD-8
ELAU AG
7.2 PacDrive PD-8
Electrical connections
Hard-copy for correction
7.2.2
control voltage IN
control voltage OUT
SERCOS connection IN
SERCOS connection OUT
SERCOS-/control voltage SCL
label field
terminator SCL
SERCOS IN
SCL 1
SCL 2
SCL 3
SCL 4
SCL 5
SCL 6
SCL 7
SCL 8
0V
24V
POWER IN
SERCOS OUT
24V
0V
POWER IN
DCDC+
PE
DCDC+
PE
power supply connection SCL
power supply connection IN
power supply connection OUT
shield connection IN
shield connection OUT
PD-8_Ansicht_de_0308.fh8
Fig. 7-3: Overview of the connections of the PacDrive PD-8
Control Signals IN
Pin
1
2
Designation
Meaning
1
24 V
24V control voltage
2
0V
0V control voltage
Range
-15%..+25%
max. cross
section
4 mm2
4 mm2
Table 7-9: Connection - control signals IN
Control Signals OUT
Pin
1
2
Designation
Meaning
1
24 V
24V control voltage
2
0V
0V control voltage
Range
-15%..+25%
max. cross
section
4 mm2
4 mm2
Table 7-10: Connection - control signals OUT
Power Supply IN/OUT
PD_OpManPS-4_07_us.fm
Pin
1 2 3
Designation
Meaning
Range
max. cross
section
1
DC +
Power supply DC+
DC 270V-370V 4 mm2
2
DC-
Power supply DC-
DC 270V-370V 4 mm2
3
PE
Protective conductor
connection
4 mm2
Table 7-11: Connection - power supply IN/OUT
ELAU AG
PacDrive PS-4 / PD-8
page 53
7 Technical Data
4
3
2
1
Pin
Designation
Meaning
max. cross
section
Range
1
PE
protective conductor
1 mm²
2
PE
shield
1 mm²
3
DC-
DC-circuit -
DC 270V-370V 1 mm²
4
DC+
DC-circuit +
DC 270V-370V 1 mm²
Table 7-12: Connection - power supply SCL
SERCOS Connection SCL
8
5
4
1
Pin
Designation
Meaning
max. cross
section
Range
1
24 V
2
SERCOS Out + SERCOS Transmit +
24V control voltage
-15%..+25%
0.5 mm²
0.5 mm²
3
shield
shield SERCOS Out
0.5 mm²
4
SERCOS In +
SERCOS Receive +
0.5 mm²
5
0V
0V control voltage
0.5 mm²
6
SERCOS Out -
SERCOS Transmit -
0.5 mm²
7
shield
shield SERCOS In
0.5 mm²
8
SERCOS IN -
SERCOS Receive -
0.5 mm²
Hard-copy for correction
Power supply SCL
Table 7-13: Connection - SERCOS SCL
7.2.3
Dimensions
97
250
238
sercos out
power out
SCL055 7
SCL055 8
Vor Inbetriebnahme, Installationshinweise in der Bedienungsanleitung beachten.
Read installation instruction, before installing.
Respectez le manuel d´instruction lors de la mise en marche.
Prima della messa in funzione del´apparecchio consultare il manuale di istruzione.
Lean las instrucciones de montaje antes de instalar.
SCL055 5
INSTALLATION!
INSTALLATION!
INSTALLATION!
INSTALLATIONE!
INSTALACION!
SCL055 6
Vor Arbeiten am Gerät, Netzanschluß trennen. Entladezeit > 2min.
Disconnect from mains supply, before working on this equipment. Electric discharge > 2min.
Coupez l´alimentation avant de manipuler l´appareil. Temps de décharge > 2min.
Disconetttere l´alimentatione prima di lavorare all´apparechio. Tempo di sacarica > 2min.
Desconecten de la red antes de trabajar con este equipo. Descarga electrica > 2min.
D=5,2 (4x)
PD-8_Massblatt_de0309.FH8
PD_OpManPS-4_07_us.fm
SCL055 3
SCL055 1
SCL055 2
sercos in
12
power in
!
HOCHSPANNUNG!
HIGH VOLTAGE!
HAUTE TENSION!
ALTA TENSIONE!
ALTO VOLTAJE!
SCL055 4
185
174
160
PD-8
PacDrive
6
Fig. 7-4: Dimensions of the PacDrive PD-8 (standard version)
page 54
PacDrive PS-4 / PD-8
ELAU AG
174
190
196
190
298
238
87,8
116
106
Hard-copy for correction
7.2 PacDrive PD-8
PD-8_AS_Massblatt.FH8
Fig. 7-5: Dimensions of the PacDrive PD-8 (aseptic version)
226
130
230
110
12
31
76
67,5
87,5
14
10
PD_OpManPS-4_07_us.fm
23,5
12
41,5
198,5
228
240
PD-8_PL_Massblatt.FH8
Fig. 7-6: Dimensions of the PacDrive PD-8 (board version)
ELAU AG
PacDrive PS-4 / PD-8
page 55
7 Technical Data
167,5
Hard-copy for correction
163,75
123
41
79,5
20,5
31
87,5
3,75
23,5
PD-4_PL_Massblatt.FH8
PD_OpManPS-4_07_us.fm
Fig. 7-7: Dimensions of the PacDrive PD-4 (board version)
page 56
PacDrive PS-4 / PD-8
ELAU AG
7.3 Declaration by the manufacturer
Korrekturausdruck
7.3
Declaration by the manufacturer
Herstellererklärung /
EC-Declaration by the manufacturer /
CE-Déclaration du fabricant
ELN
122-00/08.03
im Sinne der EG-Maschinenrichtlinie 89/392 EWG,
Anhang II Abschnitt B
as defined by EC-machinery directive 89/392 EEC,
Annexe II Section B
conformément à la directive "CE" relative aux
machines 89/392 CEE Annexe II Section B
Seite 1/1
Das von uns gelieferte Produkt
The product delivered by our company
Le produit livré par notre société
PacDrive PS-4 / PacDrive PD-8
PacDrive PS-4 / PacDrive PD-8
PacDrive PS-4 / PacDrive PD-8
ist zum Einbau in eine Maschine bestimmt.
is intended to be incorporated into a
machine.
est destiné à être installé dans une
machine.
Die Inbetriebnahme ist solange untersagt, bis festgestellt wurde, dass die
Maschine, in die dieses Produkt eingebaut werden soll, den Bestimmungen der
EG-Richtlinie entspricht.
The product must not be operated until
the machine into which this product is to
be incorporated has been declared in
conformity with the provisions of the
directive.
La mise en service des composants est
fortement déconseillée avant que la
machine dans laquelle le produit sera
installés n'ait été déclarée conforme aux
dispositions de la directive.
Hersteller:
Manufacturer:
Fabricant:
ELAU AG
Dillberg 12
D-97828 Marktheidenfeld
ELAU AG
Dillberg 12
D-97828 Marktheidenfeld
ELAU AG
Dillberg 12
D-97828 Marktheidenfeld
Stellung im Betrieb / Position :
Vorstand/Chairman
PD_OpManPS-4Aen_us.FM
3.8.2003 Günter Locherer
...........................................................
(Datum, Date / Unterschrift, Signature)
ELAU AG
PacDrive PS-4 /PD-8
Seite 57
Appendix
7.4
Modifications
08 / 2003
Operating manual newly written
04 / 2005
„
„
„
„
Aseptic variant, PD-8 connectors and cables updated
Various error Corrections and supplements
Document structure updated
Product names, definitions and layout updated
NOTE
PD_OpManPS-4Aen_us.FM
The latest documentation of the modification service for this product can be found on ELAU's homepage (http://www.elau.de).
Korrekturausdruck
„
Seite 58
PacDrive PS-4 / PD-8
ELAU AG
Korrekturausdruck
8.1 Contact
8
Appendix
8.1
Contact
For repair
Please send the components to be repaired or checked, along with
the error report, to this address:
ELAU AG
Abt. Kundendienst
house address:
Postfach 1255
Dillberg 12
97821 Marktheidenfeld
97828 Marktheidenfeld
Phone: +49 (0) 93 91 / 606-142
Fax:
+49 (0) 93 91 / 606-340
Service team
Should you need to talk to a member of our service team or require
on-site service, please contact:
ELAU AG
Dillberg 12
D-97828 Marktheidenfeld
Phone:
+49 (0) 9391 / 606 - 0
Fax:
+49 (0) 9391 / 606 - 300
e-mail:
info@elau.de
Internet:
www.elau.de
ELAU, Inc.
4201 West Wrightwood Avenue
Chicago, Illinois 60639 - USA
Phone:
+1 773 342 8400
Fax:
+1 773 342 8404
e-mail:
sales@elau.com
Internet:
www.elau.com
ELAU SYSTEMS ITALIA S.r.l.
Via Tosarelli 300
I-40050 Villanova di Castenaso (BO)
Phone:
+39 051 / 7818 70
Fax:
+39 051 / 7818 69
e-mail:
info@elau.it
Internet:
www.elau.it
NOTE
PDM_AnhangStd_us.FM
Further contact addresses you can find on the ELAU homepage
(www.elau.de).
ELAU AG
PacDrive
page 59
8 Appendix
8.2
Further Literature
ELAU can provide you with these manuals and instructions on the
PacDrive™ System:1
Korrekturausdruck
Project Manual
Art.No. 17 13 00 58 - 00x (DE, EN, FR)
Programming Manual
Art.No. 17 13 00 61 - 00x (DE, EN)
Operating Manual MC-4 MotorController
Art.No. 17 13 00 62 - 00x (DE, EN, IT, FR)
Operating Manual CAN L2
Art.No. 17 13 00 66 - 00x (DE, EN)
Operating Manual PROFIBUS-DP
Art.No. 17 13 00 67 - 00x (DE, EN)
Operating Manual SM Motor
Art.No. 17 13 00 68 - 00x (DE, EN, IT, FR)
Operating Manual EPAS-4
Art.No. 17 13 00 70 - 00x (DE, EN)
Operating Manual PacDrive Controller
Art.No. 17 13 00 71 - 00x (DE, EN, IT, FR)
Operating Manual OPC-Server
Art.No. 17 13 00 73 - 00x (DE, EN)
Operating Manual Device Net
Art.No. 17 13 00 76 - 00x (DE, EN)
Operating Manual HMI Libraries
Art.No. 17 13 00 77 - 00x (DE, EN)
Operating Manual INC-4 Incremental Encoder Module
Art.No. 17 13 00 78 - 00x (DE, EN)
Operating Manual CANopen
Art.No. 17 13 00 79 - 00x (DE, EN)
Operating Manual VarioCam® Editor ECAM-4
Art.No. 17 13 00 80 - 00x (DE, EN)
Operating Manual PacNet Module PN-4
PDM_AnhangStd_us.FM
Art.No. 17 13 00 81 - 00x (DE, EN)
Operating Manual SR Motor
Art.No. 17 13 00 82 - 00x (DE, EN)
1. Art.No. -000 (DE) german -001 (EN) english -002 (IT) italian -003 (FR) french
page 60
PacDrive
ELAU AG
8.2 Further Literature
Operating Manual BusTerminal BT-4/DIO1
Art.No. 17 13 00 83 - 00x (DE, EN)
Operating Manual TTS
Korrekturausdruck
Art.No. 17 13 00 88 - 00x (DE)
User Manual Automatic Controller Optimization
Art.No. 17 13 00 89 - 00x (DE, EN)
Operating Manual PacDrive SCL
Art.No. 17 13 00 93 - 00x (DE, EN)
Operating Manual PacDrive PS-4 und PacDrive PD-8
Art.No. 17 13 00 94 - 00x (DE, EN)
Operating Manual Evaluation Kit
Art.No. 17 13 00 95 - 00x (DE)
Operating Manual PacDrive Controller P600
PDM_AnhangStd_us.FM
Art.No. 17 13 00 96 - 00x (DE)
ELAU AG
PacDrive
page 61
8 Appendix
8.3
Product Training
Our experienced seminar leaders will enable you to make optimum
use of the vast possibilities of the PacDrive™ system.
NOTE
PDM_AnhangStd_us.FM
Please contact us for further information or to order our seminar
program. See also our homepage (www.elau.de).
Korrekturausdruck
We offer practical workshops and seminars.
page 62
PacDrive
ELAU AG
Index
8.4
Index
Korrekturausdruck
A
Approvals
MC-4 / 03 A 47, 52
automation system
structure 17
C
Cleaning 29
commissioning 31
Configuration 35
connection voltage 42
connections 48, 53
X2 - motor 49, 53
X4 - encoder (SinCos) 49,
50
contact 59
contents 3
D
declaration by the manufacturer 57
Definitions 47, 52
E
EC-declaration 57
ELAU AG 2
eMail
ELAU AG 2
EMC rules 30
Exchanging units 27
Exchanging cables 29
Exchanging the motor 28
F
features
EPAS-4 19
PacDrive Controller 19
PacDrive PS-4 20
PacDrive SCL 20
G
grounding conditions 41
PD_OperaManPS-4_usSIX.fm
H
homepage
ELAU AG 2
ELAU AG
I
internet
ELAU AG 2
L
literature 60
M
mains voltage
adjustment 42
Maintenance 25
manuals 60
modifications 58
O
operating manual 60
order numbers 38
Cables 39
SR motor 38
Overview 15
P
Packaging machine 15
physical correlations 47, 52
programming 35
R
rated voltage 42
repair 26, 59
risk
classification 8
rotary current networks
-grounded 41
-ungrounded 41
S
safety notes 8
seminare 62
service
-personnel 59
slip ring 46
spare parts 25
Storage 21
T
Technical data 41, 47
PacDrive PS-4 / PD-8
Seite 63
Index
Korrekturausdruck
trademarks 2
training 62
Transportation 21
Type plate 21, 22
PD_OperaManPS-4_usSIX.fm
U
Unpacking 21
Seite 64
PacDrive PS-4 / PD-8
ELAU AG
8.5 Form for Error Report
8.5
Form for Error Report
This error report is absoluteley necessary in order to enable
efficient processing.
Korrekturausdruck
Send the error report to your ELAU representative or to:
ELAU AG, Abt. Kundendienst
Dillberg 12, D-97828 Marktheidenfeld
Fax: +49 (0) 93 91 / 606 - 340
Sender:
Company:
City:
Date:
Department:
Name:
Phone:
Details on the defective product
Product name: ..................................................................................
Article number: .................................................................................
Serial number: ..................................................................................
Software version: ..............................................................................
Hardware code: ................................................................................
Parameter enclosed:
yes
[ ]
no
[ ]
IEC program enclosed:
yes
[ ]
no
[ ]
Details of the machine on which the problem occurred:
Machine producer: ...........................................................................
Type: ................................................................................................
Hours of operation: ...........................................................................
Machine number: ..............................................................................
Date of commissioning: ....................................................................
Producer/Type of machine control:
ELAU_FoStoerung_us.FM
.........................................................................................................
ELAU AG
PacDrive
error report page 1
8.5 Form for Error Report
Description of the problem:
..........................................................................................................
..........................................................................................................
Additional information:
Problem state:
Causes:
Concomitant phenomena:
[ ] persistent
[ ] unknown
[ ] mechanical problems
[ ] when commissioning
[ ] wiring error
[ ] failure of mains supply (24V)
[ ] occurs sporadically
[ ] mechanical damage
[ ] failure of PMC-2
[ ] occurs after about.....hours [ ] moisture inside the unit [ ] motor failure
[ ] occurs in case of shocks
[ ] encoder defective
[ ] depends on temperature
[ ] broken cable
[ ] insufficient ventilation
Korrekturausdruck
..........................................................................................................
[ ] foreign object inside unit
Does the switching cabinet have an air conditioning system?Y/N [ ]
Have similar problems occurred before on the same axis?
How often: ..............................
Did the problems occur on certain days or times of day?
..........................................................................................................
further information:
..........................................................................................................
..........................................................................................................
..........................................................................................................
..........................................................................................................
..........................................................................................................
..........................................................................................................
..........................................................................................................
..........................................................................................................
..........................................................................................................
..........................................................................................................
..........................................................................................................
..........................................................................................................
ELAU_FoStoerung_us.FM
..........................................................................................................
error report page 2
PacDrive
ELAU AG