New Discovery - AI

P R O V ID E N C E
Wooden Swing Set
Model: #40112
••
••
••
••
Owner's Manual
Frequently Asked Questions
Assembly Instructions
Warranty Information
Manufacturer: Backyard Discovery
3001 North Rouse
Pittsburg, KS 66762
1-800-856-4445
Register your new swing set on-line @ www.swingsetsonline.com
(you will also find any updates on assembly instructions and
information to order replacement parts)
Features the
fastening system.
Save this assembly manual for future reference in the event that
you need to order replacement parts.
INS-40112-04 BRS 09/12/11
Made in China
STOP
PARE
Missing A Part?
CALL US BEFORE GOING
BACK TO THE STORE!
The store where you made your purchase
does not stock parts for this item.
If you have assembly questions or if you need parts,
whether they are missing or damaged
Call Toll-Free Help Line or visit www.swingsetsonline.com
¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA!
La tienda donde realizó la compra no almacena piezas de este producto.
Si tiene preguntas sobre el ensamblaje o si necesita piezas debido a que
faltan o están dañadas
llame gratis a la línea de ayuda
1-800-856-4445
PLEASE READ THIS BEFORE STARTING ASSEMBLY
POR FAVOR LEA ESTAS INSTRUCCIONES ANTES DE COMENZAR EL ENSAMBLAJE
•
•
•
•
•
•
•
•
•
•
•
READ THE ASSEMBLY MANUAL COMPLETELY, PAYING SPECIAL ATTENTION TO THE IMPORTANT TIPS AND
SAFETY INFORMATION.
AFTER YOU HAVE READ THE ASSEMBLY MANUAL, YOU WILL BE ABLE TO DECIDE IF YOU NEED PROFESSIONAL
HELP TO COMPLETE THE ASSEMBLY OF THE STRUCTURE.
SEPARATE AND IDENTIFY ALL PARTS TO MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED.
IF YOU CAN’T FIND ALL OF THE PARTS, CHECK THE PACKING MATERIAL. SMALL PARTS MAY HAVE FALLEN INTO IT
DURING SHIPMENT.
IF YOU HAVE PROBLEMS WITH THE ASSEMBLY OR IF ANY PART IS MISSING OR
DAMAGED, PLEASE CALL THE
HELP LINE 1-800-856-4445 OR VISIT www.swingsetsonline.com
LEA EL MANUAL DE ENSAMBLAJE COMPLETAMENTE, PRESTANDO ESPECIAL ATENCIÓN A LOS CONSEJOS ÚTILES
IMPORTANTES Y A LA INFORMACIÓN SOBRE SEGURIDAD.
DESPUÉS DE QUE HAYA LEÍDO EL MANUAL DE ENSAMBLAJE, PODRÁ DECIDIR SI NECESITA AYUDA PROFESIONAL
PARA EFECTUAR EL ENSAMBLAJE DE LA ESTRUCTURA.
SEPARE E IDENTIFIQUE TODAS LAS PIEZAS PARA COMPROBAR QUE DISPONE DE TODAS LAS PARTES INDICADAS.
SI NO PUEDE ENCONTRAR TODAS LAS PIEZAS, REVISE EL MATERIAL DE EMPAQUE. ES POSIBLE QUE ALGUNAS
PIEZAS PEQUEÑAS PUEDAN HABERSE CAÍDO ALLÍ DURANTE EL ENVÍO.
MANTÉNGASE ALEJADO DE LOS NIÑOS MENORES A LA EDAD RECOMENDADA.
SI TIENE PROBLEMAS CON EL ENSAMBLAJE O SI ALGUNA PIEZA FALTA O ESTÁ DAÑADA, LLAME A LA LÍNEA DE
AYUDA AL 1-800-856-4445 O VISITE www.swingsetsonline.com
PLEASE HAVE THE FOLLOWING INFORMATION WHEN YOU MAKE YOUR CALL:
1 – MODEL NUMBER OF THE PRODUCT LOCATED ON THE FRONT OF THE ASSEMBLY MANUAL
2 – DESRIPTION OF THE PART FROM THE PARTS LIST
POR FAVOR TENGA VISIBLE LA SIGUIENTE INFORMACIÓN CUANDO LLAME:
1 - NÚMERO DE MODELO DEL PRODUCTO QUE SE ENCUENTRA UBICADO AL FRENTE DEL MANUAL
DE ENSAMBLAJE
Owner’s Manual Play Set
Dear Customer:
Please read entire booklet completely before beginning the assembly process.
Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use.
The Company does not warranty any of its residential structures subjected to commercial use such as:
Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
WARNING: This Symbol points out important safety instructions which, if not followed, could endanger
the personal safety of yourself and your children and/or damage your property. You MUST read and
follow all instructions in this manual before attempting to use this playcenter.
WARNING: Children must NOT use this playcenter until unit has been completely assembled
and inspected by an adult to insure set has been properly installed and anchored.
Please follow all recommendations below. Failure to do so may result in the warranty being void and/or safety
violations that could result in serious injury. This manual contains helpful information concerning Assembly
Preparation, Installation Procedure, and Required Maintenance. Always keep the safety of your children in mind as
your play structure is being built and as your children play on the set. Before your children play on the set please
review the Operation Instructions with them to help ensure their safety.
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE PLACE WHERE YOU CAN
REFER TO THEM AS NEEDED. IN ORDER TO PROVIDE YOU WITH THE MOST EFFICIENT SERVICE, IT IS REQUIRED THAT
YOU PROVIDE US WITH THE PART NUMBERS WHEN ORDERING PARTS.
For Your Records:
Please take time and fill out the information below. This information will be needed for warranty issues.
Where Purchased: ____________________
Date of Purchase: ____________________
Installation Date: _____________________
Installed by: _________________________
Staple Receipt Here
Tracking Number Reference Label
Remove label sticker from each carton and stick on the back side of ID plate. In the event of warranty
claim this will help identify your unit.
Rev5/20/10 BRS
Owner’s Manual Play Set
Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height.
Positioning Your Playcenter
1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult
helper. Place in a flat area of your yard to minimize ground preparation.
2. Choose a level location for the equipment. This can reduce the likelihood of the play set
tipping over and loose-fill surfacing material washing away during heavy rains.
3. Place the equipment not less than 6 ft from any structure or obstruction such as a fence,
garage, house, overhanging branches, laundry lines, or electrical wires.
4. Provide enough room so that the children can use the equipment safely. For example, for
structures with multiple play activities, a slide should not exit in front of a swing.
5. It is a good idea to place your Playcenter in an area that is convenient for adults to watch
children at play.
6. Create a site free of obstacles that could cause injuries – such as low overhanging tree
branches, overhead wires, tree stumps and/or roots, large rocks, bricks and concrete.
Additional suggestions in the Suggested Playground Surfacing Section.
7. Do not build your playset on top of surfacing material.
8. Locate bare metal platforms and slides out of direct sunlight to reduce the likelihood of serious
burns. A slide that faces north will receive the least direct sunlight.
9. Separate active and quiet activities from each other. For example, locate sandboxes away
from swings or use a guardrail or barrier to separate the sandbox from the movement of the
swings.
Suggested Playground Surfacing
Playground equipment should never be placed on hard surfaces such as concrete or asphalt.
Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Shredded bark mulch, wood chips, fine sand and fine gravel, are added as shock absorbing
materials after assembly. If used properly these materials can absorb some of the impact of a
child’s fall.
All surface material should extend a minimum of 6 feet in all directions around the play area.
Do not apply playground surfacing until after the unit is completely constructed. Playset should
not be built on top of surfacing.
Use containment, such as digging out around the perimeter and/or lining the perimeter with
landscape edging.
Installations of rubber tiles or poured-in-place surfaces (other than loose-fill materials)
generally require a professional and are not “do-it-yourself” projects.
Shall use Playground Surfacing Materials (other than loose-fill material) which comply with the
safety standard ASTM F1292 Standard Specification of Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment.
Rev5/20/10 BRS
Owner’s Manual Play Set
The following chart explains the fall height in feet from which a life threatening head injury
would not be expected
Critical Heights in feet (m) of Tested Materials
Material
Uncompressed Depth
Compressed Depth
Wood Chips
Double-Shredded bark mulch
Engineered Wood Fibers
Fine Sand
Coarse Sand
Fine Gravel
Medium Gravel
6" (152mm)
7' (2.13m)
6' (1.83m)
6' (1.83m)
5' (1.52m)
5' (1.52m)
5' (1.52m)
5' (1.52m)
9" (228mm)
10' (3.05m)
10' (3.05m)
7' (2.13m)
5' (1.52m)
5' (1.52m)
7' (2.13m)
5' (1.52m)
12" (304mm)
11' (3.35m)
11' (3.35m)
>12' (3.66m)
9' (2.74m)
6' (1.83m)
10' (3.05m)
6' (1.83m)
to 9" (228mm)
10' (3.05m)
7' (2.13m)
6' (1.83m)
5' (1.52m)
4' (1.22m)
6' (1.83m)
5' (1.52m)
Shredded Tires*
10-12' (3.0-3.6m)
N/A
N/A
N/A
*This data is from tests conducted by independent testing laboratories on a 6-inch depth of uncompressed shredded tire samples produced by four manufacturers. The tests
reported critical heights, which varied from 10 feet to greater than 12 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test
data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F1292.
Operating Instructions:
NOTE: Your children’s safety is our #1 concern. Observing the following statements
and warnings reduces the likelihood of serious or fatal injury. Please review these
safety rules regularly with your children.
1. This Playcenter is designed for specific number of occupants whose combined weight should
not exceed a designated weight on the elevated floor or the swing area, the total Unit capacity
is outlined in the Basic Setup Dimensions section of instruction manual. The maximum fall
height and recommended play area is also available in the Basic Setup Dimensions section of
the manual for the specific unit.
2. On-site adult supervision is required.
3. Instruct children not to walk close to, in front of, behind, or between moving swings or other
moving playground equipment.
4. Instruct children to sit in and never stand on swings
5. Instruct children not to twist the chains and ropes and not to loop them over the top support
bar, since this may reduce the strength of the chain or rope.
6. Instruct children not to jump from swings or other playground equipment in motion.
7. Instruct children to not to push empty seats. The seat may hit them and cause serious injury.
8. Instruct and teach children to sit in the center of the swings with their full weight on the seats.
9. Instruct children not to use the equipment in a manner other than intended.
10. Instruct children to always go down slides feet first. Never slide head first.
11. Instruct children to look before they slide to make sure no one is at the bottom.
12. Instruct children to never run up a slide, as this increases their chances of falling.
13. The parents should have the children dress appropriately with well-fitting shoes. Loose
clothing such as scarves and ponchos should not be worn. Always take off, tie up or tuck in
cords and drawstrings on children’s clothing. These things can get caught on playground
equipment and strangle a child.
14. Instruct children not to climb when the equipment is wet.
15. Instruct children to never jump from a fort deck. They should always use the ladder, ramp or
slide.
Rev5/20/10 BRS
Owner’s Manual Play Set
16. Instruct children to never crawl or walk across the top of monkey bars.
17. Instruct children to never crawl on top of a fort roof.
18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that
they cannot be looped back on it.
19. Instruct children not to attach items to the playground equipment that are not specifically
designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet
leashes, cables and chain as they may cause a strangulation hazard.
20. Instruct children to never wrap their legs around swing chain.
21. Instruct children to never slide down the swing chain.
22. Instruct children to remove their bike or other sports helmet before playing on playground
equipment.
Maintenance Instructions:
1. Check all nuts and bolts twice monthly during the usage season and tighten as required. (But
not so tight that you crack the wood) We recommend you check the swing beam and
hardware every two weeks due to wood expansion and contraction. It is particularly important
that this procedure be followed at the beginning of each season.
2. Remove plastic swing seats and take indoors or do not use when the temperature drops below
32 °F.
3. Reinstall any plastic parts, such as swing seats or any other items that were removed for the
cold season.
4. Oil all metallic moving parts monthly during the usage period.
5. Check all coverings for bolts and sharp edges twice monthly during usage season to be certain
they are in place. Replace when necessary. It is especially important to do this at the
beginning of each new season.
6. Check swing seats, ropes, cables and chains monthly during usage season for evidence of
deterioration. Replacement should be made of any swing seat that has developed cracks in
the plastic seats or has exposed metal in the edges of the swing seat. If there are already
exposed metal inserts on the edge of the seat, immediately remove the seats and chains to
prevent serious injury. Ropes, cables and chains should be removed and replaced if excessive
wear is found.
7. For rusted areas on metallic members such as monkey bars, hand supports, brackets, etc.
Sand and repaint, using a non lead-based paint meeting the requirements of Title 16 CRF Part
1303.
8. Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season
causing splinters to appear. Light sanding may be necessary to maintain a safe playing
environment. If you are treating your Playcenter with stain regularly, it will help prevent severe
checking/splitting and other weather damage.
9. We have applied a waterborne transparent stain to your unit. This is done for color only. Once
or twice a year, depending on your climate conditions, you must apply some type of protection
(sealant) to the wood of your unit. Prior to the application of sealant, lightly sand any “rough”
spots on your set. Please note this is a requirement of your warranty.
10. Creating and maintaining the Playcenter on a level location is very important. As your children
play, your Playcenter will slowly dig its way into the soil, and it is very important that it settles
evenly. Make sure the play set is level and true once each year or at the beginning of each
play season.
11. Rake and check depth of loose fill protective surfacing materials to prevent compaction and to
maintain appropriate depth. Replace as necessary (once a month during play season).
Rev5/20/10 BRS
Owner’s Manual Play Set
Disposal Instructions:
When the Playcenter use is no longer desired, it should be disassembled and disposed of in such
a way that no unreasonable hazards will exist at the time the unit is discarded.
Third Party Assembly:
Customer may, in their sole discretion, elect to use a third party person or service to assemble this
product. Backyard Discovery assumes no responsibility or liability for any charge incurred by the
Customer for any assembly services’.
Please see our warranty for more information about damaged and missing part replacement
coverage. Backyard Discovery will not reimburse Customer for the price of parts purchased.
Rev5/20/10 BRS
Owner’s Manual Play Set
APPENDIX A
Information on Playground Surfacing Materials:
The following information is from the United States Consumer Product Safety Commission’s
Information Sheet for playground surfacing material; also see the following website for additional
information: www.cpsc.gov/cpscpub/pubs/323.html.
X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS11
X3.1 The U.S. Consumer Product Safety Commission (CPSC) estimates that about 100,000 playground equipmentrelated injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms. Injuries
involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be
fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major
factor in determining the injury-causing potential of a fall. It is self evident that a fall onto a shock-absorbing surface is
less likely to cause a serious injury than a fall onto a hard surface. Playground equipment should never be placed on
hard surfaces such as concrete or asphalt and while grass may appear to be acceptable it may quickly turn to hard
packed earth in areas of high traffic. Shredded bark mulch, wood chips, fine sand or find gravel are considered to be
acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around playground
equipment.
X3.2 Table X3.1 lists the maximum height from which a child would not be expected to sustain a life-threatening head
injury in a fall onto four different loose-fill surfacing materials if they are installed and maintained at depths of 6, 9, and 12
in. However, it should be recognized that all injuries due to falls cannot be prevented no matter what surfacing material
is used.
X3.3 It is recommended that a shock absorbing material should extend a minimum of 6 ft in all directions from the
perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a
moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2
times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure.
X3.4 This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No
particular material is recommended over another. However, each material is only effective when properly maintained.
Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your
equipment. The choice of a material depends on the type and height of the playground equipment, the availability of the
material in your area, and its cost.
11
This information has been extracted from the CPSC publications “Playground Surfacing — Technical
Information Guide” and “Handbook for Public Playground Safety.” Copies of these reports can be obtained by sending
a postcard to: Office of Public Affairs, U.S. Consumer Product Safety Commission, Washington, D.C., 20207 or call the
toll-free hotline: 1-800-638-2772.
The American Society for Testing and Materials takes no position respecting the validity of any parent right
asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that
determination of the validity of any such parent rights, and the risk of infringement of such rights, are entirely their own
responsibility.
The standard is subject to revision at any time by the responsible technical committee and must be reviewed
every five years and if not revised, either approved or withdrawn. Your comments are invited either for revision of this
standard or for additional standards and should be addressed to ASTM Headquarters. Your comments will receive
careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your
comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards.
100 Barr Harbor Drive, West Conshohocken, PA 19428.
Rev5/20/10 BRS
Play Set Assembly Manual FAQs:
1. Does the area for the playset need to be level?
Yes. Backyard Discovery recommends the playset be positioned on a flat level area for
maximum safety and durability. The stakes provided should be used to secure it firmly to the
ground.
2. What size area is recommended for the playset?
Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset
for maximum safety.
3. What age range is appropriate for the playsets?
Backyard Discovery playsets are recommended for children ages 3 – 10 years.
4. Is the wood treated with chemicals?
Backyard Discovery uses 100% Chinese Cedar wood which is naturally bug resistant, decay
and rot resistant. To help ensure your child’s safety, our wood is completely chemical free and
we do not use pressure-treated wood. The stain we use is a top coat using a water-based
product that is for appearance only.
5. How often should the playset be stained?
Backyard Discovery recommends the playset be stained once each year. A water or oil based
stain can be used at the customer’s discretion.
6. Why does it seem that my swing set is developing cracks?
Wood is a natural material; no two pieces are exactly alike. Each piece has its own
characteristics and personality and reacts differently to climate changes. When any wood
product is exposed to the elements, it develops “wood checks”. A check is the radial separation
of the wood fibers running with the grain of the wood. These are caused by the varying
temperature and moisture conditions. A check is not a crack – it does not affect the strength or
durability of the wood or structural integrity of the play set.
7. Do Backyard Discovery playsets come with a warranty?
Yes. All Backyard Discovery products carry a 1-year replacement warranty on all parts for
manufacturer’s defect. Our wood carries a 5 year warranty on rot and decay as well. Please see
warranty details for more information.
8. What is the best way to get started assembling the playset?
Backyard Discovery recommends taking all the parts out of the boxes and arranging them by
part number before you begin any assembly. This will not only allow faster assembly, but will
also identify any parts that may be missing or damaged so they can be replaced before
assembly. If parts are missing or need replacement, go to
Rev5/20/10 BRS www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the
assembly manual and get the tools ready for the job as
recommended in the manual. If the assembly manual is lost or misplaced a new one can be
printed from Backyard Discovery’s website: www.swingsetsonline.com.
9. The playset seems to rock or sway too much. What’s wrong?
Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground
rails. These should be removed and the ground underneath re-leveled to prevent rocking. Also
ensure the playset is securely staked to the ground using the stakes provided.
10. The 2”x4” boards do not measure 2”x 4”. Why not?
In the U.S. it is common practice to describe lumber dimensions using the rough cut sizes from
the sawmill and not the finished dimensions. Retailers, home stores, etc. all use this accepted
practice for describing lumber dimensions. However, Backyard Discovery playsets are designed
and constructed using the actual dimensions so everything fits properly and remains so during
the life of the playset.
11. The end beam is not straight up and down. Why not?
This is normal. Backyard Discovery designs playsets this way to ensure the strongest structure
possible. The slight angle adds strength and reduces rocking and twisting.
12. The S-hooks for the swings won’t close. What is wrong?
Backyard Discovery recommends placing them on a hard surface such as concrete (don’t do
this on anything that will dent such as metal or finished wood or glass which will break!). It will
take quite a few strokes, but the hooks will close.
For more information and frequently asked questions, please refer to our website at
www.swingsetsonline.com. Rev5/20/10 BRS Tools Required for Installation:
(These are the tools that are generally required for assembly of our outdoor products. These tools
are not included with the outdoor product purchase.)
(Tape Measure)
(Cordless Drill or Electric Drill)
(An Adult w/ an Adult Helper)
(Claw Hammer)
(1/8" & 3/8" Drill Bits)
(Phillips Screw Driver)
(Rubber Mallet - Optional)
(Drill Attachments:
Phillips Head)
(Ladder)
Basic Setup Dimensions
Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such
as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.
25'-1 1/2" [7.7 m]
13'-1 1/2" [4 m]
22'-11 1/2"
[7 m]
10'-11 1/2"
[3.3 m]
6' [2 m]
Safe Play Zone
General Information:
Your set has been designed and engineered for
children only and for residential use only.
A maximum of 150 lbs. per child is recommended for
play activities designed for individual use.
A maximum of 120 lbs. per child is recommended for
play activities designed for multiple child use.
A maximum of 6 children is recommended for this
swing set.
9'-4"
[2.9 m]
6'-3"
[1.9 m]
Important Assembly Notes
Safe play height: 15'-4" [4.7 m]
Maximum fall height: 6'-3 1/2" [1.9 m]
1) While assembling unit, take time before and after each phase to make sure fort is level. If fort is
not level, assembly will be difficult and improper assembly may result. Extra care must be taken to
insure the fort is square.
2) Tighten bolts securely, tighten nuts on bolts flush to the tube or member, and place caps over
exposed bolts snug to the nut.
3) Pay close attention to the ITEMS NEEDED FOR EACH PHASE. They can be a valuable aid when
sorting your wood and hardware. Assembly will be made easier if items are sorted by phase.
4) Pay close attention to make sure you are using the correct hardware in the correct phases. Using
incorrect hardware may result in improper assembly.
5) Whenever a T-nut is used, follow these directions. Place T-nut in pre-drilled hole. Tap in with hammer.
Place bolt with washers in the opposite side. Hand tighten to make sure the bolt is in the T-nut.
DO NOT over tighten.
6) Read the steps of each phase thoroughly. The written steps may include important information not
shown in the illustrations.
Parts Identification
Wood Components
(NOT TO SCALE)
E1 - FORT UPRIGHT - W102297
(4) 1 3/8"x3 3/8"x83" (36x86x2108)
E77 - ANGLE BRACE - W100991
(2) 1 3/8"x3 3/8"x74 3/8" (36x86x1890)
G1 - PICNIC TOP SUPPORT - W102300
(2) 1"x5 1/4"x15" (24x134x381)
H1 - ROOF CROSS BRACE - W102301
(2) 1"x3 3/8"x62 1/2" (24x86x1588)
H2 - ROCKWALL SUPPORT - W102334
(2) 1"x3 3/8"x48 7/8" (24x86x1242)
H3 - TARP UPRIGHT - W102340
(2) 1"x3 3/8"x37" (24x86x940)
H4 - FLOOR JOIST - W102308
(2) 1"x3 3/8"x30" (24x86x762)
H5 - SWINGBEAM RAIL - W102303
(1) 1"x3 3/8"x30" (24x86x762)
H79 - END SUPPORT - W100992
(1) 1"x3 1/2"x42" (24x86x1072)
H80 - GROUND BOARD - W100990
(1) 1"x3 3/8"x87 3/8" (24x86x2218)
J1 - TIE STRAP - W102346
(2) 1"x2 3/8"x7" (24x60x178)
K1 - GROUND BOARD - W102299
(1) 5/8"x5 1/4"x88 7/8" (16x134x2256)
K2 - GROUND BOARD - W102298
(2) 5/8"x5 1/4"x52 1/2" (16x134x1334)
Parts Identification
Wood Components
(NOT TO SCALE)
K3 - WALL RAIL - W102302
(3) 5/8"x5 1/4"x30" (16x134x762)
K4 - ARCHED WALL RAIL - W102306
(2) 5/8"x5 1/4"x30" (16x134x762)
K5 - OUTER FLOOR BOARD - W102333
(2) 5/8"x5 1/4"x27 1/8" (16x134x688)
M1 - ANGLE BRACE - W102310
(2) 5/8"x3 3/8"x59" (16x86x1500)
M2 - TARP SUPPORT - W102337
(2) 5/8"x3 3/8"x31 7/8" (16x86x810)
M3 - PICNIC SEAT/TOP - W102347
(4) 5/8"x3 3/8"x31" (16x86x786)
M4 - FLOOR BOARD - W102332
(6) 5/8"x3 3/8"x30 7/8" (16x86x785)
M5 - FLOOR SUPPORT - W102309
(2) 5/8"x3 3/8"x30" (16x86x762)
M6 - FLOOR SUPPORT - W102331
(2) 5/8"x3 3/8"x30" (16x86x762)
H6 - FLOOR SUPPORT - W102338
(1) 1"x3 3/8"x30" (24x86x762)
M8 - TARP SUPPORT - W102341
(1) 5/8"x3 3/8"x30" (16x86x762)
M9 - WALL SLAT - W102342
(6) 5/8"x3 3/8"x23" (16x86x584)
M10 - ROCKWALL BOARD - W102335
(2) 5/8"x3 3/8"x20 1/4" (16x86x514)
Parts Identification
Wood Components
(NOT TO SCALE)
M11 - ROCKWALL BOARD - W102336
(6) 5/8"x3 3/8"x20 1/4" (16x86x514)
M12 - WALL RAIL - W102339
(2) 5/8"x3 3/8"x4" (16x86x102)
M77 - SLIDE BRACE - W100544
(1) 5/8"x3 3/8"x17 1/4" (16x86x438)
M78 - CENTER SLIDE BRACE - W100545
(2) 5/8"x3 3/8"x17 1/4" (16x86x438)
N1 - WALL SLAT - W102343
(2) 5/8"x2 3/8"x23" (16x60x584)
N2 - PICNIC TABLE BRACE - W102345
(4) 5/8"x2 3/8"x12" (16x60x305)
N3 - TIE STRAP - W102344
(2) 5/8"x2 3/8"x6" (16x60x152)
O1 - SAFETY BOARD - W102307
(1) 5/8"x1 3/8"x30" (16x34x762)
SB74 - SWING BEAM - W102304
(1) 2"x5 1/4"x89 1/2" (50x134x2274)
W71 - SWING BEAM SUPPORT - W102349
(1) 2"x3 3/8"x47 3/8" (50x86x1204)
Parts Identification
Hardware
(6) BOLT WH 5/16x1/2 - H100115
(2) BOLT WH 5/16x1 - H100008
(23) BOLT WH 5/16x1-1/2 - H100010
(4) BOLT HEX 5/16x1-1/4 - H100042
(2) BOLT HEX 5/16x2-3/4 - H100047
(7) BOLT FA 3/8x1-1/2 - H100001
(6) BOLT WH 5/16x1-3/4 - H100011
(1) LAG SCREW WH 5/16x1-1/2 - H100026
(16) BOLT WH 5/16x2 - H100012
(26) LAG SCREW WH 5/16x2 - H100027
(2) BOLT WH 5/16x2-1/4 - H100013
(4) BOLT WH 1/4x1" - H100137
(2) BOLT WH 5/16x2-1/2 - H100014
(14) SCREW PWH 8x5/8 - H100128
(1) BOLT WH 5/16x4-1/2 - H100021
Parts Identification
Hardware
(92) SCREW PFH 8x1-1/8" - H100088
(4) T-NUT 1/4 - H100072
(57) SCREW PFH 8x1-1/2" - H100086
(7) SCREW PFH 8x2 - H100111
(13) SCREW PFH 8x2-1/4 - H100091
(6) T-NUT 5/16 - H100074
(9) NUT BARREL WH 5/16x5/8 - H100004
(47) NUT BARREL WH 5/16x7/8 - H100005
(2) NUT BARREL WH 5/16x1-1/2 - H100006
(9) NUT LOCK 5/16 - H100110
(6) SWING HANGER QUICK LINK - H100099
(33) SCREW PFH 8x3 - H100092
(6) T-NUT 3/8 - H100073
(58) WASHER LOCK EXT 12x19 - H100031
(73) WASHER LOCK EXT 8x19 - H100030
(4) WASHER LOCK EXT 6x15 - H100138
(4) WASHER SPLIT 5/16 - H100095
(4) WASHER SAFETY 17x30 - H100103
(13) WASHER FLAT 8x27 - H100105
Parts Identification
Accessories
(NOT TO SCALE)
- SLIDE RAIL 8' BLUE RIGHT
(1) GZ
-A100161
- SLIDE RAIL 8' BLUE LEFT
(1) HA
-A100162
EM - SLIDE BED 8' YELLOW
(1) -A100056
- TARP .4x760x2505
(1) SC
-A100310
(2) TQ - SWING SEAT WITH BLUE ROPE CHAIN - A100170
(1) KF - TRAPEZE WITH BLUE ROPE CHAIN - A100109
Parts Identification
Accessories
(NOT TO SCALE)
- T-40 Wrench
(2) -A100041
- HAND GRIP YELLOW PLASTIC
(2) EA
-A100043
- T-40 Torx Driver
(2) -A100042
- CLIMBING ROCK BLUE SMALL
(6) GX
-A100159
- PLASTIC GROUND STAKE BROWN
(6) KD
-A100179
- L BRACKET 66x66x127 BLUE
(2) GQ
-A100153
- T-30 Torx Driver
(2) -A100147
- T-30 Wrench
(2) -H100114
(1) BYD ID TAG (LARGE) 2011 WITH AGES - A100164
(2)
SB - TRIANGLE PLATE 100 5 HOLE
-A100309
8 FOOT SLIDE ASSEMBLY
PHASE 1
STEP 1
TOP
● DRILL 3 HOLES AT ONE END OF THE PLASTIC SLIDE BED USING A 3/8" DRILL BIT AND USING THE
DIMENSIONS SHOWN BELOW. THIS END WILL BE THE TOP OF THE SLIDE.
● TAKE NOTE OF SLIDE BED SURFACE FINISH, THE DULL SIDE WILL BE TOWARDS THE GROUND. PLACE
SLIDE BRACE CENTERED ON THE BOTTOM (DULL SIDE) AND 1/4" FROM THE EDGE. TRANSFER HOLES
ON THE BOARD THROUGH THE SLIDE BED AS SHOWN BELOW. USE A 3/8" DRILL BIT.
● ATTACH SLIDE BRACE TO SLIDE USING HARDWARE SHOWN.
BRIGHT SIDE
TOP
13 5/8
8 5/8
3 5/8
1
BOTTOM
SLIDE BED 8' YELLOW
NUT BARREL WH 5/16x5/8
WASHER LOCK EXT 12x19
SLIDE BRACE
BOLT WH 5/16x1/2
TIP: PREBENDING THE ENDS WILL EASE ASSEMBLY.
REV 8/02/11 BRS
8 FOOT SLIDE ASSEMBLY
STEP 2
PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE
SLIDE RAIL. PUT SLIDE SUPPORT BOTTOM INTO THE SUPPORT POCKET AT THE BOTTOM OF THE
RAIL AND HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT
THE BED INTO THE SLIDE CAVITY. MAKE SURE SLIDE BED IS COMPLETELY DOWN IN THE SLIDE
CAVITY.
PLACE THE OTHER SLIDE RAIL ON A FLAT SURFACE WITH THE SLIDE CAVITY UP. HAVE A HELPER
HOLD THE TOP END OF SLIDE BED AND BEGIN INSERTING THE SLIDE BED AND SLIDE BRACES INTO
THE CAVITY AND SUPPORT POCKETS STARTING AT THE BOTTOM OF SLIDE AND WORKING UP TO
THE TOP.
ONCE BED AND BRACES ARE COMPLETELY IN THE CAVITY AND IN THE SUPPORT POCKETS, SECURE
USING 3" SCREWS AT EACH OF THE PILOT HOLE LOCATIONS AS SHOWN BELOW.
SLIDE RAIL 8' BLUE RIGHT
CENTER SLIDE BRACE
SLIDE RAIL 8' BLUE LEFT
SCREW PFH 8x3
TIP: A HELPER IS REQUIRED FOR THIS PHASE.
(1)
SB74 - SWING BEAM - W102304
2"x5 1/4"x89 1/2" (50x134x2274)
(2) GQ - L BRACKET 66x66x127 BLUE - A100153
(2) SB - TRIANGLE PLATE 100 5 HOLE - A100309
SWING BEAM ASSEMBLY
(3)
STEP 1
BOLT WH
5/16x1-3/4
(2)
ATTACH (2) SB TRIANGLE PLATES TO SB74 SWING BEAM USING
1-3/4" BOLTS, LOCK WASHER AND 7/8" BARREL NUT.
(3)
WASHER
LOCK EXT
12x19
(4)
ATTACH (2) GQ L BRACKETS TO SB74 SWING BEAM USING 2-3/4"
HEX BOLTS, FLAT WASHERS AND 5/16" LOCK NUTS.
BOLT HEX
5/16x2-3/4
WASHER
FLAT 8x27
BARREL
(3) NUT
WH 5/16x7/8
(2)
GQ
SB74
GQ
SB
NUT LOCK
5/16
(1)
W71 - SWING BEAM SUPPORT - W102349
2"x3 3/8"x47 3/8" (50x86x1204)
(1)
H79 - END SUPPORT - W100992
1"x3 1/2"x42" (24x86x1072)
(2)
E77 - ANGLE BRACE - W100991
1 3/8"x3 3/8"x74 3/8" (36x86x1890)
(1)
H80 - GROUND BOARD - W100990
1"x3 3/8"x87 3/8" (24x86x2218)
SWING BEAM ASSEMBLY
(4)
STEP 2
INSERT (2) 2-1/2" BOLTS, LOCK WASHERS
AND 1-1/2" BARREL NUTS INTO TOP EDGE OF
W71 SWING BEAM SUPPORT, AS SHOWN.
ATTACH E77 ANGLE BRACES TO W71 SWING
BEAM SUPPORT USING 4- 1/2" BOLTS, LOCK
WASHERS AND 7/8" BARREL NUTS.
BOLT WH
5/16x2
BOLT WH
(2) 5/16x2-1/2
(9)
WASHER
LOCK EXT
8x19
(7)
WASHER
LOCK EXT
12x19
NUT BARREL
(2)WH
5/16x1-1/2 NUT BARREL
(5) WH 5/16x7/8
ATTACH H80 GROUND BOARD TO E77 A
NGLE BRACES USING 2" BOLTS, LOCK WAS
HERS AND 7/8" BARREL NUTS.
E77
H79
E77
H80
BOLT WH
5/16x4-1/2
SCREW
(2) LAG
WH 5/16x2
W71
ATTACH H79 END SUPPORT TO E77 A
NGLE BRACES USING 2" BOLTS, LOCK WAS
HERS AND 7/8" BARREL NUTS. NOW ATTACH
H79 END SUPPORT TO W71 SWING
BEAM SUPPORT USING 2" LAG SCREWS AND
LOCK WASHERS.
(1)
SWING BEAM ASSEMBLY
STEP 3
(4)
WASHER
FLAT 8x27
(2)
ATTACH (2) SB TRIANGLE PLATES TO W71 SWING BEAM SUPPORT USING 1-3/4"
BOLTS, LOCK WASHER AND 7/8" BARREL NUT.
(4)
INSERT SWING HANGER QUICK LINK AND SAFETY WASHER INTO HOLES IN
THE EDGE OF SB74 SWING BEAM. SECURE SWING HANGER TO W71 SWING
BEAM USING FLAT WASHERS AND 5/16" LOCK NUTS.
BOLT WH
5/16x1-3/4
NUT LOCK
5/16
(2)
WASHER
LOCK EXT
12x19
BARREL
(2) NUT
WH 5/16x7/8
(4)
SB74
SB
W71
SWING
HANGER
QUICK LINK
(4)
WASHER
SAFETY
17x30
M1 - ANGLE BRACE - W102310
5/8"x3 3/8"x59" (16x86x1500)
(1)
K1 - GROUND BOARD - W102299
5/8"x5 1/4"x88 7/8" (16x134x2256)
(2)
E1 - FORT UPRIGHT - W102297
1 3/8"x3 3/8"x83" (36x86x2108)
(1)
K3 - WALL RAIL - W102302
5/8"x5 1/4"x30" (16x134x762)
(1)
H1 - ROOF CROSS BRACE - W102301
1"x3 3/8"x62 1/2" (24x86x1588)
(1)
M6 - FLOOR SUPPORT - W102331
5/8"x3 3/8"x30" (16x86x762)
(2)
(1)
H4 - FLOOR JOIST - W102308
1"x3 3/8"x30" (24x86x762)
(1)
H5 - SWINGBEAM RAIL - W102303
1"x3 3/8"x30" (24x86x762)
STEP 1
E1
LAY TWO E1 FORT UPRIGHTS FLAT ON
GROUND.
WASHER
(4) LOCK EXT
8x19
ATTACH K1 BOARD TO E1 FORT
UPRIGHTS USING 1- 1/2" BOLTS, LOCK
WASHERS AND 7/8" BARREL NUTS.
BOLT WH
(4) 5/16x1-1/2
K1
PILOT HOLE SHOULD
APPEAR TO THE
OUTSIDE OF E1 FORT
UPRIGHTS.
WASHER
(4) LOCK EXT
12x19
NUT BARREL
(4) WH 5/16x7/8
STEP 2
ATTACH M1 ANGLE BRACE AND M6 FLOOR SUPPORT TO E1 FORT UPRIGHTS USING
2-1/4" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS.
ATTACH H4
FLOOR JOIST TO
E1 FORT
UPRIGHTS
USING 2"
BOLTS, LOCK
WASHERS AND
7/8" BARREL
NUTS.
BOLT WH
BOLT WH
(2) 5/16x2-1/4 (2) 5/16x2
M6
M1
M1
NUT BARREL
(2) WH 5/16x5/8
BOLT WH
(2) 5/16x1
H4
WASHER
(6) LOCK EXT
12x19
ATTACH M1 ANGLE BRACE TO K1
GROUND BOARD USING 1" BOLTS, LOCK
WASHERS AND 5/8" BARREL NUTS.
WASHER
(6) LOCK EXT
E1
8x19
NUT BARREL
(4) WH 5/16x7/8
K1
STEP 3
ATTACH K3 WALL RAIL TO E1
FORT UPRIGHTS USING 1-1/2"
BOLTS, LOCK WASHERS AND 7/8"
BARREL NUTS.
H1
BOLT WH
(4) 5/16x1-1/2
BOLT WH
(4) 5/16x2
ATTACH H5 SWINGBEAM RAIL TO
E1 FORT UPRIGHTS USING 2"
BOLTS, LOCK WASHERS AND 7/8"
BARREL NUTS.
H5
WASHER
(8) LOCK EXT
8x19
ATTACH H1 ROFF CROSS BRACE
TO E1 FORT UPRIGHTS USING 2"
BOLTS, LOCK WASHERS AND 7/8"
BARREL NUTS.
WASHER
(8) LOCK EXT
E1
K3
12x19
NUT BARREL
(8) WH
5/16x7/8
(2)
E1 - FORT UPRIGHT - W102297
1 3/8"x3 3/8"x83" (36x86x2108)
(2)
K3 - WALL RAIL - W102302
5/8"x5 1/4"x30" (16x134x762)
(1)
H4 - FLOOR JOIST - W102308
1"x3 3/8"x30" (24x86x762)
(1)
H1 - ROOF CROSS BRACE - W102301
1"x3 3/8"x62 1/2" (24x86x1588)
(1)
M6 - FLOOR SUPPORT - W102331
5/8"x3 3/8"x30" (16x86x762)
(1)
O1 - SAFETY BOARD - W102307
5/8"x1 3/8"x30" (16x34x762)
STEP 4
LAY TWO E1 FORT UPRIGHTS FLAT ON
GROUND.
E1
WASHER
(4) LOCK EXT
8x19
ATTACH K3 WALL RAIL TO E1 FORT
UPRIGHTS USING 1- 1/2" BOLTS, LOCK
WASHERS AND 7/8" BARREL NUTS.
(4)
BOLT WH
5/16x1-1/2
WASHER
(4) LOCK EXT
12x19
(4)
NUT BARREL
WH 5/16x7/8
PILOT HOLES SHOULD APPEAR TO
THE OUTSIDE OF E1 FORT UPRIGHTS.
K3
STEP 5
ATTACH H4 FLOOR JOIST TO E1
FORT UPRIGHTS USING 2" BOLTS,
LOCK WASHERS AND 7/8" BARREL
NUTS.
E1
M6
(2)
(2)
ATTACH M6 FLOOR SUPPORT TO E1
FORT UPRIGHTS USING 1-1/2"
BOLTS, LOCK WASHERS AND 7/8"
BARREL NUTS.
BOLT WH
5/16x2
BOLT WH
5/16x1-1/2
WASHER
(4) LOCK EXT
12x19
WASHER
(4) LOCK EXT
8x19
H4
(4)
STEP 6
H1
ATTACH K3 WALL RAIL TO E1
FORT UPRIGHTS USING 1-1/2"
BOLTS, LOCK WASHERS AND
7/8" BARREL NUTS.
ATTACH O1 SAFETY BOARD TO
E1 FORT UPRIGHTS USING
1-1/2" BOLTS, LOCK WASHERS
AND 7/8" BARREL NUTS.
ATTACH H1 ROFF CROSS
BRACE TO E1 FORT UPRIGHTS
USING 2" BOLTS, LOCK
WASHERS AND 7/8" BARREL
NUTS.
NUT BARREL
WH 5/16x7/8
(6)
(2)
O1
BOLT WH
5/16x2
BOLT WH
5/16x1-1/2
WASHER
(8) LOCK EXT
12x19
WASHER
(8) LOCK EXT
8x19
E1
K3
(8)
NUT BARREL
WH 5/16x7/8
(2)
K4 - ARCHED WALL RAIL - W102306
5/8"x5 1/4"x30" (16x134x762)
(2)
M5 - FLOOR SUPPORT - W102309
5/8"x3 3/8"x30" (16x86x762)
(2)
K2 - GROUND BOARD - W102298
5/8"x5 1/4"x52 1/2" (16x134x1334)
(2)
M2 - TARP SUPPORT - W102337
5/8"x3 3/8"x31 7/8" (16x86x810)
STEP 7
E1
E1
STAND UP UPRIGHT
ASSEMBLIES AND ATTACH
(2) K2 GROUND BOARDS TO
E1 FORT UPRIGHTS USING
2" LAG SCREWS AND LOCK
WASHERS.
(8)
WASHER
(8) LOCK EXT
8x19
K2
STEP 8
E1
LAG SCREW
WH 5/16x2
E1
ATTACH (2) M5 FLOOR
SUPPORTS TO E1 FORT
UPRIGHTS USING 2" LAG
SCREWS AND LOCK
WASHERS.
(4)
LAG SCREW
WH 5/16x2
M5
M5
WASHER
(4) LOCK EXT
8x19
STEP 9
ATTACH K4 ARCHED
WALL RAILS TO E1
FORT UPRIGHTS
USING 2" LAG
SCREWS AND LOCK
WASHERS.
H1
E1
M2
M2
(8)
H1
PILOT DRILL USING 1/8"
BIT (USE HOLES IN TARP
SUPPORTS AS GUIDE).
ATTACH M2 TARP
SUPPORTS TO E1 FORT
UPRIGHTS USING 2-1/4"
WOOD SCREWS.
LAG SCREW
WH 5/16x2
(8)
SCREW PFH
8x2-1/4
K4
K4
E1
WASHER
(8) LOCK EXT
8x19
(2)
(1)
K5 - OUTER FLOOR BOARD - W102333
5/8"x5 1/4"x27 1/8" (16x134x688)
H6 - FLOOR SUPPORT - W102338
1"x3 3/8"x30" (24x86x762)
STEP 10
ATTACH H6 FLOOR SUPPORT TO M5
FLOOR SUPPORTS USING 2-1/4" SCREWS.
H6
M5
(8)
SCREW PFH
8x2-1/4
(4)
SCREW PFH
8x1-1/2"
H6
STEP 11
K5
ATTACH (2) K5 OUTER FLOOR
BOARDS TO H4 FLOOR JOISTS
AND M5 FLOOR SUPPORTS
USING 1-1/2" WOOD SCREWS.
M5
H4
M5
H4
(6)
M4 - FLOOR BOARD - W102332
5/8"x3 3/8"x30 7/8" (16x86x785)
(2)
STEP 12
M12 - WALL RAIL - W102339
5/8"x3 3/8"x4" (16x86x102)
M4
EVENLY SPACE (6) M4 FLOOR BOARDS
AND ATTACH TO H4 FLOOR JOISTS
USING 1-1/2" SCREWS.
H4
ATTACH H6 FLOOR SUPPORT TO M4
FLOOR BOARDS USING 1-1/2" SCREWS.
H6
H4
(20)
SCREW PFH
8x1-1/2"
(2)
LAG SCREW
WH 5/16x2
1/16 GAP
TYP.
M4
STEP 13
ATTACH (2) M12 WALL RAILS TO E1
FORT UPRIGHTS USING 2" LAG
SCREWS AND LOCK WASHERS.
E1
M12
WASHER
(2) LOCK EXT
8x19
(6)
(2)
M11 - ROCKWALL BOARD - W102336
5/8"x3 3/8"x20 1/4" (16x86x514)
H2 - ROCKWALL SUPPORT - W102334
1"x3 3/8"x48 7/8" (24x86x1242)
(6) GX - CLIMBING ROCK BLUE SMALL - A100159
M10 - ROCKWALL BOARD - W102335
(2)
5/8"x3 3/8"x20 1/4" (16x86x514)
STEP 14
TO BUILD THE ROCK WALL
LADDER ASSEMBLY,
START BY ATTACHING THE
GX CLIMBING ROCKS TO
M11 WALL BOARDS USING
1-1/2" BOLTS, 3/8" T-NUTS
AND 1-1/8" WOOD SCREWS.
GX
GX
(6)
M11
STARTING AT THE BOTTM
OF H2 ROCK WALL
SUPPORTS, ATTACH M10
AND M11 ROCK WALL
BOARDS FLUSH WITH
OUTSIDE EDGES OF H2
SUPPORTS AND 2-5/8" UP
2 5/8"
FROM START POINT USING
1-1/2" WOOD SCREWS, AS
SHOWN.
(6)
BOLT FA
3/8x1-1/2
(6)
T-NUT 3/8
(32)
SCREW PFH
8x1-1/8"
SCREW PFH
8x1-1/2"
M10
H2
2 5/8"
WALL BOARD ATTACHMENT START POINT.
STEP 15
PILOT DRILL USING 1/8" BIT AND ATTACH
ROCK WALL LADDER ASSEMBLY TO M5
FLOOR SUPPORT USING 3" WOOD SCREWS.
SEE LOCATION DIAGRAM BELOW FOR
DRILLING LOCATION.
4 7/8"
1/2"
(2)
M5
M5
ROCK WALL LADDER ASSEMBLY
SCREW PFH
8x3
(6)
M9 - WALL SLAT - W102342
5/8"x3 3/8"x23" (16x86x584)
STEP 16
ATTACH (3) M9 WALL SLATS TO K3 WALL RAIL AND M6 FLOOR SUPPORT USING 1-1/8"
WOOD SCREWS.
3 1/4"
(3 PLCS)
K3
(12)
M9
SCREW PFH
8x1-1/8"
1 13/16"
M6
STEP 17
ATTACH (3) M9 WALL SLATS TO K3 WALL RAIL AND M6 FLOOR SUPPORT USING 1-1/8"
WOOD SCREWS.
3 1/4"
(3 SPCS)
K3
M9
M6
1 13/16"
(12)
SCREW PFH
8x1-1/8"
(2)
N1 - WALL SLAT - W102343
5/8"x2 3/8"x23" (16x60x584)
(1)
M8 - TARP SUPPORT - W102341
5/8"x3 3/8"x30" (16x86x762)
(2)
H3 - TARP UPRIGHT - W102340
1"x3 3/8"x37" (24x86x940)
STEP 18
ATTACH (2) N1 WALL SLATS TO K4 ARCHED WALL RAIL AND M12
WALL RAIL USING 1-1/8" WOOD SCREWS.
N1
22 7/16"
N1
N1
(8)
SCREW PFH
8x1-1/8"
K4
M12
1 15/16"
STEP 19
M8
ATTACH H3 TARP UPRIGHT TO
H1 ROOF CROSS BRACE AND
K3 WALL RAIL USING 2" BOLT,
LOCK WASHER, 5/16" T-NUT
AND 1-1/2" WOOD SCREWS.
ATTACH H3 TARP UPRIGHT TO
H1 ROOF CROSS BRACE AND
K3 WALL RAIL USING 1-1/2"
BOLT, LOCK WASHERS, 7/8"
BARREL NUT AND 1-1/2" WOOD
SCREWS.
ATTACH M8 TARP SUPPORT TO
THE ENDS OF H3 TARP
UPRIGHTS USING 2-1/4" WOOD
SCREWS.
(1)
(1) BOLT WH
5/16x2
BOLT WH
5/16x1-1/2
H3
T-NUT
WASHER
WASHER (1) LOCK EXT
(2) LOCK EXT
12x19
8x19
BARREL
NUT
(1)
T-NUT 5/16
(1)
(4)
SCREW PFH
8x2-1/4
(4)
K3
NUT BARREL
WH 5/16x7/8
H1
H1
K3
SCREW PFH
8x1-1/2"
(1)
SC - TARP .4x760x2505 - A100310
1/64"x29 7/8"x98 5/8" (.4x760x2505)
STEP 20
DRAPE SC TARP OVER M2
AND M8 TARP SUPPORTS.
ATTACH ONE SIDE OF
TARP TO INSIDE OF ONE
M2 TARP SUPPORT USING
5/8" SCREWS. PULL
OTHER SIDE OF TARP
TIGHT AND ATTACH TO
OTHER M2 TARP SUPPORT
USING 5/8" SCREWS.
SECURE TOP OF TARP TO
M8 TARP SUPPORT USING
5/8" SCREWS, AS SHOWN.
SC
M8
(9)
M2
M2
SCREW PWH
8x5/8
(2)
G1 - PICNIC TOP SUPPORT - W102300
1"x5 1/4"x15" (24x134x381)
PILOT DRILL HOLE LOCATION
3 15/16"
6 15/16"
1 1/8"
27 13/16"
E1
G1
(4)
SCREW PFH
8x3
BOARD PLACEMENT DIMEMSION
STEP 21
PILOT DRILL USING 1/8" BIT AND ATTACH (2) G1 PICNIC TOP
SUPPORTS TO E1 FORT UPRIGHTS USING 3" WOOD SCREWS.
SEE PILOT DRILL HOLE LOCATION & BOARD PLACEMENT
DIMENSIONS FOR PROPER PLACEMENT.
M3 - PICNIC SEAT/TOP - W102347
5/8"x3 3/8"x31" (16x86x786)
(4)
(2)
N3 - TIE STRAP - W102344
5/8"x2 3/8"x6" (16x60x152)
N3
M3
STEP 22
(4)
(4)
SCREW PFH
8x1-1/8"
ATTACH N3 TIE STRAP TO (2) M3 PICNIC
SEAT / TOP USING 1-1/8" WOOD SCREWS.
REPEAT PROCESS TO ASSEMBLE PICNIC
TABLE SEAT ASSEMBLY.
SCREW PFH
8x1-1/2"
STEP 23
ATTACH PICNIC TABLE TOP ASSEMBLY TO G1 PICNIC
TOP SUPPORTS USING 1-1/2" WOOD SCREWS.
TABLE TOP ASSEMBLY
G1
(4)
N2 - PICNIC TABLE BRACE - W102345
5/8"x2 3/8"x12" (16x60x305)
(2)
J1 - TIE STRAP - W102346
1"x2 3/8"x7" (24x60x178)
STEP 24
ATTACH J1 TIE STRAP TO (2) N2
PICNIC TABLE BRACES USING
1-1/2" WOOD SCREWS. REPEAT
PROCESS TO ASSEMBLE SECOND
SEAT SUPPORT ASSEMBLY.
J1
SCREW PFH
(8) 8x1-1/8"
SCREW PFH
(4) 8x1-1/2"
N2
STEP 25
ATTACH SEAT SUPPORT ASSEMBLY TO K2 GROUND BOARDS USING 1-1/8" WOOD SCREWS.
SEAT SUPPORT ASSEMBLY
K2
K2
TABLE TOP & SEAT ASSEMBLY
SCREW PFH
(4) 8x1-1/2"
STEP 26
ATTACH TABLE TOP & SEAT ASSEMBLY
TO (2) J1 TIE STRAPS USING 1-1/2" WOOD
SCREWS.
TABLE TOP & SEAT ASSEMBLY
J1
(2) EA - HAND GRIP YELLOW PLASTIC - A100043
BOLT WH
(4) 1/4x1"
WASHER
(4) LOCK EXT
6x15
(4) T-NUT 1/4
STEP 27
N1
ATTACH EA HANDLE GRIPS TO N1 WALL
SLATS USING 1/4"x 1" BOLTS, 6x15 LOCK
WASHERS AND 1/4" T-NUTS. USING A
5/16" DRILL BIT PILOT DRILL AND
INSTALL 1/4" T-NUTS INTO THE BACK
SIDE OF N1 WALL SLATS. SECURE INTO
PLACE USING A HAMMER.
8 3/16"
4 3/16"
1 7/16"
HANDLE ATTACHMENT
DRILL PATTERN
EA
STEP 28
BEGIN BY PILOT DRILLING H1 ROOF CROSS BRACE WITH 3/8" BIT
USING SWING BEAM ASSEMBLY ANGLE BRACKETS AS A TEMPLATE.
ATTACH SWING BEAM ASSEMBLY TO H1 ROOF CROSS BRACE AND
H5 SWING BEAM RAIL USING 1-1/4" HEX BOLTS, SPLIT WASHERS,
FLAT WASHERS AND 5/16" T-NUTS.
WASHER
(4) SPLIT 5/16
BOLT HEX
(4) 5/16x1-1/4
ATTACH HC ID PLATE TO SWING BEAM USING 5/8" SCREWS, AS
SHOWN.
WASHER
(4) FLAT 8x27
H1
(4) T-NUT 5/16
SCREW PWH
(4) 8x5/8
H5
HC
STEP 29
CENTER SLIDE ASSEMBLY IN OPENING, AS SHOWN.
USING HOLE PATTERN BELOW, PILOT DRILL (3) SLIDE ATTACHMENT HOLES IN
SLIDE BED AND K5 OUTER FLOOR BOARD USING 3/8" BIT AND ATTACH SLIDE
ASSEMBLY USING 1/2" BOLTS, LOCK WASHER AND 5/8" BARREL NUTS.
BOLT WH
(3) 5/16x1/2
WASHER
(3) LOCK EXT
12x19
NUT BARREL
(3) WH 5/16x5/8
SLIDE ASSEMBLY
6 1/4"
2 5/8"
3 3/4"
1"
K5
(6) KD - PLASTIC GROUND STAKE BROWN - A100179
(1) KF - TRAPEZE WITH BLUE ROPE CHAIN - A100109
(1) TQ - SWING SEAT WITH BLUE ROPE CHAIN - A100170
Anchoring Instructions
*STAKES SHOULD BE PLACED IN CONCRETE*
NOTE:
FAILURE TO USE STAKES CAN VOID
WARRANTY & CAUSE INJURY!
STAKE
STAKE
STEP 30
SWING
(6)
DRIVE STAKES INTO GROUND AGAINST
BOARDS WHERE SHOWN AND ATTACH
WITH 2" WOOD SCREWS.
ATTACH TQ SWING SEATS ASSEMBLY TO
SWING BEAM ASSEMBLY.
SCREW PFH
8x2
TRAPEZE
ATTACH KF TRAPEZE ASSEMBLY TO
SWING BEAM ASSEMBLY.
SWING
STAKE
STAKE
STAKE
TIGHTEN
QUICK
LINK
FINAL STEP
DOUBLE CHECK EVERY BOLT, SCREW AND NUT FOR TIGHTNESS. MAKE
SURE EVERY BOARD IS SECURE AND MAKE SURE THE PLAYSET IS LEVEL.
ENJOY YOUR NEW PLAYSET!
INSERT CHAIN
INTO
QUICK LINK
STAKE
Limited Warranty
This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery
brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time
Products.
Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of
one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood,
hardware, and accessories. All wood carries a five (5) year pro-rated warranty against rot and decay. Refer to
the schedule below for charges associated with replacement of parts under this Limited Warranty. In addition,
Backyard Discovery will replace any parts within the first 30 days from date of purchase found to be missing
from or damaged in the original packaging.
This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is
required to assure maximum life and performance of this product and failure by the owner to maintain the
product according to the maintenance requirements may void this warranty. Maintenance guidelines are
provided in the Owner’s Manual.
This Limited Warranty does not cover:








Labor for any inspection
Labor for replacement of any defective item(s)
Incidental or consequential damages
Cosmetic defects which do not affect performance or integrity of a part or the entire product
Vandalism, improper use, failure due to loading or use beyond the capacities stated in the applicable
Assembly Manual.
Acts of nature including but not limited to wind, storms, hail, floods, excessive water exposure
Improper installation including but not limited to installation on uneven, unlevel, or soft ground
Minor twisting, warping, checking, or any other natural occurring properties of wood that do not affect
performance or integrity
Backyard Discovery products have been designed for safety and quality. Any modifications made to the
original product could damage the structural integrity of the unit leading to failure and possible injury.
Modification voids any and all warranties and Backyard Discovery assumes no liability for any modified
products or consequences resulting from failure of a modified product.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Backyard Discovery
product be used in public settings. Such use may lead to product failure and potential injury. Any and all public
use will void this warranty. Backyard Discovery disclaims all other representations and warranties of any kind,
express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state
or province to province. This warranty excludes all consequential damages, however, some states do not allow
the limitation or exclusion of consequential damages and therefore this limitation may not apply to you.
Pro Rated Part Replacement Schedule
Product Age
All Parts
0-30 days from date of purchase
31 days to 1 year
Customer Pays
$0 and free shipping
$0 + S&H
Wood Rot and Decay Only
1 year
2 years
3 years
4 years
5 years
Over 5 years
$0 and free shipping
20% + S&H
40% + S&H
60% + S&H
80% + S&H
100% + S&H
Rev5/20/10 BRS