Vivotek IP8332 Installation guide

Outdoor H.264 Day/Night Weather-proof
Quick Installation Guide
English
ᖅϛ
ᙏϛ
Рҏᇭ
Français
Español
Deutsch
Português
Italiano
Türkçe
Polski
Русский
Česky
Svenska
IP8330
Supreme Night Visibility
60 fps @ VGA
IP8332
Megapixel
This guide describes the basic functions of IP8330 / IP8332.
All detailed information is described in the user's manual.
IP Sur veillance
English
Warning Before Installation
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Refer to your user's manual for the
operating temperature.
Contact your distributor in the
event of occurrence.
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not insert sharp or tiny objects
into the Network Camera.
Do not drop the Network Camera.
EN-1
1
Package Contents
IP8330 / IP8332
Waterproof Connector (3 holes, for
backup use)
Silica Gel
Camera Stand
Silica
gel
Power Adapter
RJ45 Female/Female Coupler
Quick Installation Guide
/ Warranty Card
Software CD
510000202G
EN-2
English
2
Physical Description
Front Panel
IR LED
Lens
Light Sensor
Inner View
Reset Button
MicroSD/SDHC Card Slot
Connectors
General I/O Terminal Block
Ethernet 10/100 RJ45 Plug
Power Cord Socket (black)
EN-3
3
Hardware Installation
1. Loose the waterproof connector, then remove the rubber.
2. Loose the back cover.
3. Tear down the aluminum foil vacuum bag and take out the silica gel. Attach the
supplied silica gel to the inner side of the Network Camera. (Please replace the silica
gel with a new one if you open the back cover after installation.)
4. Make sure all cable lines are securely connected.
5. Tighten the back cover, rubber and waterproof connector.
6. Secure the Network Camera to the wall/ceiling by the supplied camera stand.
2
6
1
Wall Mount
3
Ceiling Mount
5
Silica
gel
Note
If you want to use your own cable lines, please loose two supplied screws and take out
the power board. Then be careful to make connections as the illustration shown below.
Ethernet Cable
Power Cord
Terminal Block (from left to right)
1: AC24V (red)
2: AC24V (red)
3: DI (white)
4: GND (black)
Screws
EN-4
English
4
Network Deployment
General Connection (without PoE)
1. If you have external devices such as
sensors and alarms, make the connection
from general I/O terminal block.
GND
DI
AC24V
AC24V
GND : Ground
DI
: Digital Input
AC24V: 24V
AC24V: 24V
2. Use the supplied RJ45 female/female
coupler to connect the Network Camera
to a switch.
Use Category 5 Cross Cable when
Network Camera is directly connected to
PC.
POWER
LINK
COLLISION
1
2
3
4
5
RECEIVE
PARTITION
3. Connect the power cable from the
Network Camera to a power outlet.
EN-5
Power over Ethernet (PoE)
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data
via a single Ethernet cable. Follow the below illustration to connect the Network
Camera to a PoE-enabled switch via Ethernet cable.
POWER
COLLISION
1
2
3
4
5
LINK
RECEIVE
PARTITION
PoE Switch
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and
a non-PoE switch.
PoE Power Injector
(optional)
Non-PoE Switch
POWER
EN-6
COLLISION
1
2
3
4
5
LINK
RECEIVE
PARTITION
English
5 Assigning an IP Address
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the “Next” button to continue the program.
IW2
Installation
Wizard 2
3. The program will search for all VIVOTEK Video Receivers, Video Servers, and
Network Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the bottom of your device to connect to the Network Camera via
Internet Explorer.
Network Camera
Model No: IP8330
RoHS
MAC:0002D1733012
00-02-D1-73-30-12
192.168.5.109
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Pat. 6,930,709
0002D1733012
Made in Taiwan
EN-7
IP8330
6
Ready to Use
1. Access the Network Camera from the LAN.
2. Retrieve live video through web browsers or recording software.
2010/03/12 14:53:02
For further setup, please refer to the user’s manual on the software CD.
EN-8
Copyright
P/N: 625010600G Ver.1.0
2010 VIVOTEK INC. All right reserved.