Avital 2200
Owner's Guide
By Mark Chasey at 2:21 pm, 6/1/04
Limited Lifetime
Consumer Warranty
For a period of one calendar year from the date of purchase of this auto-security
device, Directed Electronics, Inc. promises to the ORIGINAL PURCHASER to repair or
replace (with a comparable reconditioned model), free of cost, any electronic control
module which proves to be defective in workmanship or material under normal use,
SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL
AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY
INSTALLED. If warranty service is necessary you must have a clear copy of your sales
receipt containing all of the information shown on the following page.
After the first calendar year, from the date of purchase of this auto-security device,
Directed Electronics, Inc., promises to the ORIGINAL PURCHASER to repair or replace
(with a comparable reconditioned model) any electronic control module which proves
to be defective in workmanship or material under normal use FOR A CHARGE OF
$45.00, SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS
ORIGINALLY INSTALLED. If warranty service is necessary you must have a clear copy
of your sales receipt containing all of the information shown on the following page.
This warranty contains the entire agreement relating to warranty and supersedes all
previous and contemporaneous representations or understandings, whether written or
oral. IN ANY EVENT, DIRECTED ELECTRONICS IS NOT LIABLE FOR THE THEFT OF THE
VEHICLE AND/OR ITS CONTENTS.
This warranty is void if the product has been damaged by accident, unreasonable use,
neglect, improper service or other causes not arising out of defects in materials or
construction. This warranty is nontransferable and does not apply to any unit that
has been modified or used in a manner contrary to its intended purpose and does not
cover batteries. The unit in question must be returned to the manufacturer, postage
prepaid. This warranty does not cover labor costs for the removal, diagnosis, troubleshooting or reinstallation of the unit. For service on an out-of-warranty product a
flat rate fee by model is charged. Contact your authorized dealer to obtain the service charge for your unit.
These systems are a deterrent against possible theft. Directed Electronics, Inc. is not
offering a guarantee or insuring against the theft of the automobile or its contents
and disclaims any liability for the theft of the vehicle and/or its contents. Directed
Electronics does not authorize any person to create for it any other obligation or liability in connection with this security system.
© 2004 Directed Electronics, Inc.
i
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF
NON-INFRINGEMENT OF PATENTS, IN THE UNITED STATES OF AMERICA AND/OR
ABROAD. NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH
SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT
NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, TOWING,
REPAIR, REPLACEMENT, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL
LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE
ABOVE, MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR
THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or
consequential damages. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
$2,500 Limited Theft Protection Guarantee
Terms and Conditions. Available only in the USA. In the event that your vehicle is
stolen and not recovered, Directed Electronics, Inc. will refund to the original purchaser of the Avital system up to $2,500 of your insurance deductible. This vehicle
protection guarantee is valid only if:
(1) The installation was performed by an authorized Avital dealer.
(2) The warranty registration card is completed and mailed within ten (10) days of
purchase.
(3) At the time of the theft, the system was fully functional and not in “valet mode.”
(4) The vehicle and its contents were insured at the time of the theft.
(5) The insurance company and the police have been notified and a written stolen
vehicle report was issued by the Police Department.
(6) No less than thirty (30) days after the police report was issued, you mail Directed
Electronics, Inc. clear photocopies of the following documents:
a.
b.
c.
d.
ii
Proof of Purchase OR provide the system model and name of the company
that installed the system.
The stolen vehicle report issued by the police.
Insurance coverage documents for the stolen vehicle, clearly showing all the
details, including the vehicle identification number and the insurance
deductible amount.
A dated declaration signed by you the owner of the vehicle, attesting that
the vehicle has been stolen for more than thirty (30) days and has not been
recovered.
© 2004 Directed Electronics, Inc.
This vehicle theft protection is effective for one (1) year from the date of purchase
and is limited to one claim. This vehicle theft protection guarantee is valid only for
the theft of the entire vehicle and specifically excludes any other considerations,
including, but not limited to, damage caused to the vehicle, theft of parts, contents
or any other consequential damages. Once Avital Technologies verifies that all the
above listed terms and conditions have been met, a check for the insurance
deductible (up to $2,500) will be mailed within thirty (30) days.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
■
■
■
■
■
■
■
■
■
Date of purchase
Your full name and address
Authorized dealer's company name and address
Type of alarm installed
Year, make, model and color of the automobile
Automobile license number
Vehicle identification number
All security options installed on automobile
Installation receipts
© 2004 Directed Electronics, Inc.
iii
Table of Contents
Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
What Is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Your Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FCC/ID Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Remote Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Using Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disarming Without a Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote-Controlled Silent Arm/Disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote-Controlled Valet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Nuisance Prevention Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Arming Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Disarming Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table of Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Stealth Coding™ Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
High Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programming Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Security & Convenience Expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installation Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Glossary Of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Quick Reference Guide (Removable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
© 2004 Directed Electronics, Inc.
1
2
© 2004 Directed Electronics, Inc.
What is Included
■
A control module
■
Two 3-button remote remotes
■
A zone 2 impact sensor on-board the control module
■
A high-powered siren
■
A fault-proof starter interrupt relay on-board the control module
■
An LED system status indicator
■
A push-button Valet® switch
Important Information
Congratulations on the purchase of your state-of-the-art vehicle
security system. This system has been designed to provide years of
trouble-free operation. By carefully reading this guide prior to
using your system, you will maximize the use of this product and
its features.
System Maintenance
Your vehicle security system has no specific maintenance requirements. The remote is powered by a lightweight 3-volt lithium
battery that will last approximately one year under normal use.
When the battery begins to weaken, the LED on the remote will dim
and you will notice reduced operating range when using the
© 2004 Directed Electronics, Inc.
3
remote. To access the battery for replacement, remove the rear
cover of the remote with a small, flat-blade screwdriver.
Your Warranty
Your warranty card must be returned and the barcode serial number must not be removed. If the warranty card is not returned, no
warranty will be honored on your unit. It is also necessary to keep
your proof of purchase, which reflects that the product was
installed by an authorized dealer. Make sure you receive the warranty card from your dealer.
FCC/ID Notice
This device complies with Part 15 of FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable
operation.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate this device.
4
© 2004 Directed Electronics, Inc.
Remote Functions
This system is programmable, making it possible to assign any
remote button to any specific receiver function. The remote initially comes programmed with Standard Configuration, but may
also be customized by an authorized dealer. The buttons in all of
the instructions in this manual correspond to a Standard
Configuration remote.
Standard Configuration
Button
The arm/disarm/panic functions are usually controlled by
.
Button
An optional accessory function (such as trunk release), remote-controlled silent arm/disarm, and remote-controlled Valet® are usually
controlled by
work by pressing
. (Silent arm/disarm and remote-controlled Valet®
for less than one second. An optional accessory
output is controlled by pressing and holding
for 1.5 seconds.)
This accessory output controls ____________________________.
Button
An optional accessory convenience or expansion function that you
have added to your system can be activated by pressing
.
This accessory output controls_____________________________.
© 2004 Directed Electronics, Inc.
5
Using Your System
The buttons indicated in all instructions in this manual correspond
to a standard configuration remote, unless otherwise specified.
Arming
You can arm the security system by pressing
for one second.
When the system arms, you will hear a short siren sound (chirp)
and the parking lights will flash once. If the power door locks are
controlled by the system, the doors will also lock. Once armed, the
LED system status indicator will flash once per second to indicate
that the system is actively protecting your vehicle. If you hear a
second chirp after arming and notice that the LED system status
indicator is flashing in a grouped pattern, this signals Bypass
Notification. Bypass Notification is described in detail in the
Diagnostics section of this manual.
Your security system can also be programmed for Passive Arming.
With Passive Arming, the system automatically arms itself 30 seconds after the ignition has been turned off and the last door has
been closed. During the 30-second Passive Arming countdown, the
LED system status indicator will flash twice as fast as it does when
the system is armed. If the system is programmed for Passive
Arming, care must be taken to prevent the keys from being locked
in the vehicle.
NOTE: If any protected entry point, such as a door or switch-protected
trunk or hood, is open, Passive Arming will not engage. Additionally, each
6
© 2004 Directed Electronics, Inc.
time a sensor is triggered during the Passive Arming countdown, the
countdown starts over.
Arming the system protects your vehicle in the following ways:
■
Light impacts trigger a warn-away response, causing the siren
to chirp and the parking lights to flash for a few seconds.
■
Heavy impacts trip a trigger sequence, which consists of the
siren sounding continuously and the parking lights flashing
for 30 seconds.
■
If a door is opened, the siren immediately starts chirping and
the parking lights start flashing to provide an instant response.
Three seconds later, the siren output changes to a continuous
blast. This two-stage progressive response allows you time to
disarm the security system with your remote, in case the door
is inadvertently opened while the system is armed.
■
Turning on the ignition key triggers the same two-stage progressive response as opening a door.
■
The starter interrupt prevents the vehicle’s starter from cranking.
Disarming
Press
to disarm the system when it is already armed. If the
power locks are controlled by the system, the doors will also unlock.
Disarming is confirmed when the parking lights flash twice and the
siren emits two chirps. The LED system status indicator will also
stop flashing. The siren chirping either four or five times when disarming indicates Tamper Alert, which is described in the Diagnostics
section of this guide.
© 2004 Directed Electronics, Inc.
7
NOTE: When using the standard 3-button remote there is a
15-second delay between disarming and rearming the system. This delay
was included to accommodate the progressive unlock feature (described
in the Installation Options section of this guide), when installed. To
rearm the system during the 15-second delay, simply press
twice.
Disarming Without a Remote
If your remote is lost or damaged, you can manually disarm the
security system. To disarm the security system without a remote,
you
must
have
the
vehicle's
ignition
key
and
know where the Valet switch is located. Be sure to check with
your installer at the time of installation for the location of the
Valet switch.
To disarm the system, turn the
ignition key on and press the
Valet switch within 15 seconds.
The system should now disarm.
DRW-35
If the system does not disarm, you may have waited too long to
press the Valet switch; turn the ignition off and repeat the process.
Location of Valet Switch_________________________________
Panic Mode
If you are threatened in or near your vehicle, you can press
for 1.5 seconds to trigger Panic Mode on your security system and attract attention. The siren will sound and the parking
lights will flash for 30 seconds. To stop Panic Mode at any time,
press
8
again.
© 2004 Directed Electronics, Inc.
Remote-Controlled Silent Arm/Disarm
Use remote-controlled silent arm/disarm to temporarily turn off the
arm or disarm chirps by briefly pressing
before either arming
or disarming. The confirmation chirp(s) will then be eliminated for
that one operation only. To permanently turn off the arm and disarm chirps, contact your installation dealer.
NOTE: The warn-away response to lighter impacts is bypassed if the system is armed using the Remote Controlled Silent Arm/Disarm. This
ensures that the siren does not chirp in an environment where you do not
want chirps to be emitted. The system is still capable of being triggered
by heavier impacts; only the warn-away response generated by light
impacts is bypassed.
Valet Mode
Valet Mode prevents your security system from arming and
triggering
either
automatically
or
with
the
remote.
In Valet Mode, the system will not arm, but all convenience
functions (door locks, trunk release, etc.) remain operational.
This feature is useful when washing or servicing your vehicle.
You can access Valet Mode either manually or from the remote.
To enter or exit Valet Mode with the Valet switch:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
switch within 10 seconds.
DRW-35
The LED system status indicator will light solidly if you are entering Valet Mode and will turn off if you are exiting Valet Mode.
© 2004 Directed Electronics, Inc.
9
Remote-Controlled Valet ®
You can also enter or exit Valet Mode by using the remote :
1. Open any vehicle door.
2. Press
3. Press
4. Press
.
.
again.
The LED system status indicator will light solidly if you have
entered Valet Mode and will turn off if you have exited Valet Mode.
Nuisance Prevention ® Circuitry
Your security system has Nuisance Prevention Circuitry™ (NPC™) to
prevent annoying false alarms. This circuitry is designed to prevent
repetitive trigger sequences due to faulty door pinswitches or environmental conditions such as thunder, jackhammers, airport
noise, etc.
Here's how it works: If the alarm is triggered by the same sensor
or switch three times within a 60 minute period, your system
interprets this pattern of triggers as false alarms. After the third
trigger, NPC™ ignores, or bypasses, that sensor or switch (along
with any other sensors or switches sharing the same zone) for 60
minutes. If the bypassed sensor is triggered again while it is
already being bypassed, the 60-minute bypass period will start over,
ensuring that a sensor that is continually being triggered will
remain bypassed.
The vehicle doors are protected differently by NPC™. If your secu10
© 2004 Directed Electronics, Inc.
rity system is triggered by an open door for three, full 30-second
cycles (one and one half minutes), the system will bypass the
doors until the trigger ceases.
NOTE: Arming and disarming the system does not reset the NPC™. The only
ways to reset a bypassed zone are for that zone not to be triggered for
60 minutes or to turn the ignition key on. When testing your system, it
is important to remember that NPC™ can cause zones to be bypassed and
appear to not work. If five chirps are heard when disarming the system,
NPC™ has been engaged. To clear the NPC™ memory, simply turn the ignition key on.
Diagnostics
The microprocessor at the heart of your system has the ability to
constantly monitor all of the switches and sensors connected to it.
It can detect any faulty switches or sensors and prevent them from
disabling the entire system. It can also record and report any triggers that occur when you are away from your vehicle.
Arming Diagnostics
If the system is armed at the same time that an input is active
(door opening, sensor triggering, etc.), you will hear one chirp to
indicate arming and a second chirp a few seconds later to indicate
Bypass Notification. A Bypass Notification chirp means that the system ignores the input that was active when the system was armed,
until that input ceases. Three seconds after that input ceases, the
system will resume normal monitoring. For example, if your vehicle
© 2004 Directed Electronics, Inc.
11
has an interior light exit delay and you arm the system before the
light turns off, you may hear a Bypass Notification chirp. Three seconds after the light turns off, however, normal monitoring resumes.
NOTE: Bypass Notification does not occur when the system is in remotecontrolled silent arm/disarm mode or if the chirps have been programmed
not to sound.
Disarming Diagnostics
Your system has a Tamper Alert feature that notifies you of system
triggers that occur while you are away from your vehicle. If you
hear four chirps when you disarm, this indicates that the system
was triggered in your absence. If you hear five chirps when you
disarm, this indicates that a specific zone was triggered so many
times that the NPC™ has bypassed that zone. In both cases, the
pattern of the flashing LED system status indicator indicates which
zone was triggered (see Table of Zones). The LED system status
indicator does not, however, report when warn-away responses
have activated; it only reports triggered sequences. The system
retains this information in its memory and will continue to chirp
four or five times each time the system is disarmed, until the next
time the ignition is turned on.
Table of Zones
A zone is represented by the number of LED flashes used by the
system to identify a particular type of input. Standard input assignments are listed in the following table, along with spaces to write
in any optional sensors or switches that you have had installed.
12
© 2004 Directed Electronics, Inc.
ZONE
(Number of
LED Flashes)
DESCRIPTION
1
Instant trigger for optional
hood or trunk pins
2
A heavier impact detected by
the on-board shock sensor
3
Door switch trigger
5
Ignition trigger
DEALER-INSTALLED
OPTIONS
NOTE: The LED does not report when the warn-away response has been
activated; it only reports triggered sequences.
Stealth Coding
Technology
™
The receiver and remote use mathematical formulas called algorithms to change their codes each time the remote is used. This
Stealth Coding™ Technology has been developed to increase the
security of the unit. By following this set code sequence, the
receiver and remote stay synchronized, even if the remote is used
out of range of the vehicle. If, however, the remote is pressed many
times out of range, or the battery is removed, the remote may get
temporarily out of sync and fail to operate the system. To resynchronize the remote, simply press
several times within range
of the vehicle. The system will automatically resynchronize and the
remote will respond normally.
© 2004 Directed Electronics, Inc.
13
High Frequency
Your system transmits and receives at 434 MHz. This provides a
cleaner spectrum with less interference and a more stable signal.
Enjoy a phenomenal increase in range, even in areas with high
radio interference.
Programming Options
Programming options control your system's normal, operational
set-up. Most options do not require additional parts, but some may
require installation labor. This system's programming options are
listed below, with the factory default settings in bold:
■
Active arming (only with the remote) or passive arming (automatic arming 30 seconds after the last vehicle door is closed).
■
Active door locking (only when arming with the remote) or
passive door locking (selectable only when Passive Arming
has been programmed).
■
Arming and disarming confirmation siren chirps can be programmed on or off.
■
Ignition controlled door lock feature, on or off. With this feature on, the doors will lock three seconds after the ignition
key is turned on, and unlock when the ignition is turned off.
14
© 2004 Directed Electronics, Inc.
The system also prevents the doors from locking when the
ignition is turned on while any vehicle door is open.
Security & Convenience
Expansions
Listed below are some of the many expansion options available for
use with your system. Please consult your dealer for a detailed
explanation of all the available options.
Audio Sensor: Metal on glass, glass cracking, and breaking glass
produce distinctive acoustic signatures. The 506T audio sensor uses
a microphone to detect these sounds, and then analyzes them with
proprietary acoustic software to determine if the glass has been
tampered with or broken.
Backup Battery: The 520T Backup Battery ensures that the system
stays armed, triggers the alarm and keeps the optional starter
interrupt active if main battery power is disconnected.
Field Disturbance Sensor: An invisible dome of coverage is established by the 508D "radar" sensor. The security system will respond
to any intrusions into this field by initiating the triggered sequence.
Power Locks: This system offers lock outputs that can control some
manufacturers' power door lock systems. For other systems, additional parts may be required.
© 2004 Directed Electronics, Inc.
15
Power Trunk Release: The
output of the system can operate a
factory power release for the vehicle's trunk or hatch. An optional
relay is required. If the factory release is not power-activated, then
Direcred Electronics 522T trunk release solenoid can be added in
most cases.
Power Window Control: Automatic power window control is provided with the 529T and 530T systems. These options operate power
windows, by rolling them up, down, or both up and down. The 530T
also offers one-touch switch operation.
Valet™ Start System: For the ultimate in convenience, the Valet
Start System can start your vehicle, monitor engine functions and
activate your climate control system with a push of a button! Overrev protection, open-hood lockout, brake pedal shutoff and
automatic timer shutoff are included. (This option is available only
for fuel-injected, automatic-transmission vehicles.)
Installation Options
Installation options may require additional parts or labor. Please
consult your dealer.
Progressive Unlocking: With electric power door locks, the system
can be configured so that when disarmed, only the driver’s door
unlocks. A second press of the disarm button within 15 seconds of
disarming unlocks the remaining doors.
16
© 2004 Directed Electronics, Inc.
Horn Honk: If connected, the horn will sound if the alarm is either
triggered by an intrusion or activated by Panic Mode. (In most
vehicles, this feature requires that an additional relay be installed.)
Interior Light Illumination: The interior domelight can be configured to illuminate for 30 seconds after the alarm is disarmed. If
the system is rearmed during that 30-second period, the interior
light illumination will terminate until the alarm is disarmed once
again.
Glossary of Terms
Control Module: The "brain" of your security system, usually
hidden underneath the dash. It houses the microprocessor that
monitors your vehicle and controls all of the security system’s
functions.
Fault-Proof Starter Interrupt Relay: Located on-board the control
module, this is an automatic switch controlled by the security
system that prevents the starter from cranking whenever the
system is armed. The vehicle is never prevented from cranking
when the security system is disarmed, in Valet Mode, or if the
starter interrupt fails.
Input: Any physical connection to the security system. An input
can be provided through a sensor, pinswitch or by existing systems
in the vehicle, such as ignition or courtesy lights.
© 2004 Directed Electronics, Inc.
17
LED: A red light mounted inside the vehicle, at a location determined by the installer. The LED indicates the status of your system
and also reports triggers and faults in the system or sensors.
Shock Sensor: A dual-stage shock sensor, located on-board the
control module, that detects impacts to the vehicle.
Siren: A noise generating device, usually installed in the engine
compartment of the vehicle. The siren generates the chirps and
tones heard when the system is triggered.
Remote: A hand-held, transmitter control that operates the various
functions of the security system.
Trigger or Triggered Sequence: The "setting off" or "tripping" of
the alarm. A triggered sequence consists of the siren sounding and
the parking lights flashing for 30 seconds.
Valet Switch: A small, push-button switch mounted inside the
vehicle, at a location determined by the installer. This switch is
used to override the alarm when a remote is lost or damaged, or
can be used to put the system into Valet Mode.
Warn-Away Response: Light impacts generate this response, which consists of several seconds of siren chirps and flashing parking lights.
Zone: A zone is a separate input that the alarm recognizes as
unique. Each input to the system is connected to a particular zone.
Two or more inputs may share the same zone.
18
© 2004 Directed Electronics, Inc.
✂
QUICK REFERENCE GUIDE
■ Press
on your remote for one second. When the system arms, you
will hear a short siren sound, or chirp, and see the parking lights flash
once. If the vehicle's power door locks are controlled by the system, the
doors will lock.
Disarming:
■ Press
again. You will hear two chirps, and the parking lights will
flash twice. If the power door locks are controlled by the system, the
doors will unlock.
Disarming without a remote:
■ Turn on the ignition. Press the Valet switch within 15 seconds. The system should now disarm. If it does not disarm, you may have waited too
long to press the Valet switch; turn the ignition off and on and try
again.
Remote-controlled silent arm/disarm:
■ Press
briefly before arming or disarming, and the confirmation
chirp(s) will be eliminated for that one operation only.
Panic Mode:
■ Press
for 1.5 seconds, and you will enter Panic Mode. The siren
will sound and the parking lights will flash for 30 seconds. To stop Panic
Mode at any time, press
on the remote again.
To enter or exit Valet Mode with the Valet switch:
■ Turn the ignition to the ON position, then turn to the OFF position.
Press and release the Valet switch within 10 seconds.
Remote-controlled Valet®:
■ You can also enter or exit Valet Mode by using the remote. First, open
any vehicle door. Then press
. Press
. Press
again. The LED
system status indicator will light solidly if you have entered Valet Mode
and will turn off if you have exited Valet Mode.
✂
Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet.
To arm using your remote:
© 2004 Directed Electronics, Inc.
19
The company behind this system is Directed Electronics, Inc.
Since its inception, Directed Electronics, Inc. has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of
advanced electronic technology, Directed Electronics, Inc. is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America
and around the world.
Call (800) 274-0200 for more information about our products and services.
Directed Electornics, Inc. is committed to delivering world class quality products
and
services that excite and delight our customers.
Vista, CA 92081
www.directed.com
© 2004 Directed Electronics, Inc. - All rights reserved
G2200 06/04