User’s Manual
CPS600E
CyberPower Europe
CyberPower Systems B.V.
Flight Forum 3545, 5657DW Eindhoven, The Netherlands
Tel: +31 (0)40 2348170
Fax: +31 (0)40 2340314
Website: http://eu.cyberpowersystems.com/
E-mail: sales@cyberpower-eu.com
K01-0000186-00
CPS600E
Content
SAFETY AND EMC INSTRUCTIONS ................................... 2
INSTALLING YOUR EPS ...................................................... 4
UNPACKING ......................................................................................... 4
AUTOMATIC VOLTAGE REGULATOR ............................................... 4
HARDWARE INSTALLATION GUIDE ................................................... 4
BASIC OPERATION .............................................................. 5
DESCRIPTION ..................................................................................... 5
REPLACING THE BATTERY ................................................ 6
DEFINITIONS FOR ILLUMINATED LCD .............................. 7
EPS STATUS INQUIRY AND FUNCTIONS SETUP ............. 8
GENERAL MODE ................................................................................. 8
SET-UP MODE ..................................................................................... 8
FAULT WARNING DISPLAY AND ALARM ........................ 10
TROUBLESHOOTING ......................................................... 11
TECHNICAL SPECIFICATIONS ......................................... 12
1
Copyright © 2010 CyberPower Systems, Inc.
CPS600E
SAFETY AND EMC INSTRUCTIONS
This manual contains important safety instructions. Please read and follow all instructions carefully during
installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or
operate your Emergency Power System (EPS).
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled
indoor area free of conductive contaminants. (Please see specifications for acceptable temperature and
humidity range).
CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the battery.
There are no serviceable parts inside, except for the battery.
CAUTION! EPS must be connected to an AC power outlet with circuit breaker protection. Do not plug
into an outlet that is not grounded. If you need to de-energize this equipment, turn off and unplug the unit.
CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before
servicing EPS, replacing the external battery or installing equipment.
CAUTION! To reduce the risk of fire, only connect the EPS to a circuit with 10 amperes maximum
branch circuit over-current protection in accordance with the CE requirement.
CAUTION! The building wiring socket outlet (shockproof socket outlet) must be easily accessible and
close to the EPS.
CAUTION! Please use only VDE-tested, CE-marked mains cable (e.g. the mains cable of your
equipment) to connect the EPS to the building wiring socket outlet (shockproof socket outlet).
CAUTION! Please use only VDE-tested, CE-marked power cables to connect the loads to the EPS.
CAUTION! When installing the equipment, ensure that the sum of the leakage current of the EPS and the
connected equipment does not exceed 3.5mA.
CAUTION! Do not disconnect the mains cable on the EPS or the building wiring socket outlet
(shockproof socket outlet) during operations since this would remove the protective ground of the EPS
and of all connected loads.
CAUTION! This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT!
DO NOT use in any circumstance that would affect operation and safety of any life support equipment,
any medical applications or patient care.
DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use
with or near an aquarium. Condensation from the aquarium can cause the unit to short out.
DO NOT INSTALL THE EPS WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR NEAR
HEAT!
DO NOT BLOCK OFF VENTILATION OPENINGS IN THE EPS’S HOUSING!
Copyright © 2010 CyberPower Systems, Inc.
2
CPS600E
SAFETY:
EN62040-1-1
EMI:
Conducted Emission: IEC/EN 62040-2…Category C2
Radiated Emission: IEC/EN 62040-2……Category C2
Harmonic Current: IEC/EN61000-3-2
Voltage Fluctuations and Flicker: IEC/EN61000-3-3
EMS:
IEC/EN61000-4-2(ESD)
IEC/EN61000-4-3(RS)
IEC/EN61000-4-4(EFT)
IEC/EN61000-4-5(lightning surge)
IEC/EN61000-2-2 (Immunity to low frequency signals)
3
Copyright © 2010 CyberPower Systems, Inc.
CPS600E
INSTALLING YOUR EPS
UNPACKING
Inspect the EPS upon receipt. The box should contain the following:
EPS unit x 1; User manual x 1; Input Power Cord x 1; DC Fuse x 2
AUTOMATIC VOLTAGE REGULATOR
Utility power is inconsistent. The EPS increases low voltage to computer safe 220 volts. The EPS
automatically provides battery backup (External battery connection required) if the voltage drops below
170 volts or exceeds 270 volts.
HARDWARE INSTALLATION GUIDE
1. Your new EPS may be used immediately upon receipt. However, recharging the external battery for at
least 8 hours is recommended to ensure that the battery’s maximum charge capacity is achieved. To
recharge the external battery, simply leave the unit plugged into an AC outlet when EPS is ON.
2. DO NOT use with medical or life support equipment. DO NOT use with or near aquariums as
condensation may cause the unit to short out.
3. After connecting the hard wires, plug the EPS into a 2 pole, 3 wire grounded receptacle (wall outlet).
Make sure the wall branch outlet is protected by a fuse or circuit breaker and does not service
equipment with large electrical demands (e.g. air conditioner, copier, etc…). The warranty prohibits the
use of extension cords, outlet strips, and surge strips.
4. Press the power switch to turn the unit on. The power on indicator light will illuminate and the unit will
beep once.
5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct
this, turn the EPS off and unplug the equipment from the AC outlet. Ensure that the equipment plugged
into the outlet does not exceed the UPS unit’s rated capacity (600VA/420W for CPS600E). If the
rated capacities of the unit are exceeded, an overload condition may occur and cause the UPS unit to
shut down or the input fuse to blow. For more information, refer to the “Troubleshooting” section.
6. To maintain optimum battery charge performance, make the EPS plugged into an AC outlet at all
times.
7. The UPS is designed for horizontal or wall-mount use only. To ensure safety, please follow the
placement directions as shown below.
Copyright © 2010 CyberPower Systems, Inc.
4
CPS600E
BASIC OPERATION
DESCRIPTION
1. Power Switch
Used as the master on/off switch for equipment connected to the AC outlet.
2. Power On Indicator
This LED is above the power switch. It illuminates when the utility condition is normal and the AC outlet
is providing power, free of surges and spikes.
3. Multifunction LCD Readout
High resolution and intelligent LCD display shows all the EPS information with icons and messages.
For more information please check the DEFINITIONS FOR ILLUMINATED LCD INDICATORS section.
4. LCD Display Toggle / Selected Switch
Users can monitor EPS status and set up functions using the toggle. The buzzer on/off can also be
controlled by the toggle switch. Please refer to “EPS Status Inquiry and Functions Setup” section for
more details.
5. AC Outlet
The unit has one Schuko type outlet for connected equipment to ensure temporary uninterrupted
operation during a power failure. Max. Output is 6.3A; Max. Output wattage is 420W.
Note! Maximum cord length is 10 meters and the cable O.D. must be 14AWG or greater.
6. AC Inlet
Connect to utility power through the input power cord.
Note:The O.D. of the distribution cables must be 0.75mm or greater.
Input Fuse
The fuse provides optimal overload protection.
Note:The Input Fuse is 6.3A/250V.
7. Black Battery Cable (Negative (-))
Connect black (negative (-)) battery cable to the black (negative (-)) connector on the external battery.
Note: The Battery cable is 10AWG / 4 feet.
8. Red Battery Cable (Positive (+))
Connect red (positive (+)) battery cable to the red (positive (+)) connector on the external battery.
Note: The Battery cable is 10AWG / 4 feet.
9. DC Fuse
The fuse provides optimal overload protection for battery mode operation.
5
Copyright © 2010 CyberPower Systems, Inc.
CPS600E
REPLACING THE BATTERY
CAUTION!
Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the
battery. Battery service should only be done by qualified professionals.
CAUTION!
Use only the specified type and number of external batteries. Please see the technical
specifications for replacement batteries.
CAUTION!
The battery may present a risk of electrical shock. Do not dispose of battery in a fire as
it may explode. Follow all local ordinances regarding proper disposal of batteries. Lead-acid batteries
should be recycled.
CAUTION!
Do not open or mutilate the batteries. Released electrolyte is harmful to skin and eyes
and may be toxic.
CAUTION!
A battery can present a high risk of short circuit current and electrical shock.
Take the following precautions before replacing the battery:
1.
Remove all watches, rings or other metal objects.
2.
Only use tools with insulated handles.
3.
Do not lay tools or metal parts on top of battery or any terminals.
4.
Wear rubber gloves and boots.
5.
Determine if the external battery is inadvertently grounded. If grounded, remove the source of
ground. CONTACT WITH GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK!
Copyright © 2010 CyberPower Systems, Inc.
6
CPS600E
DEFINITIONS FOR ILLUMINATED LCD
The LCD Display indicates a variety of EPS
operational conditions. All descriptions apply
when the EPS is plugged into an AC outlet and
turned on or when the EPS is on battery.
1. INPUT VOLTAGE Meter: This meter measures the AC voltage that the EPS is receiving from the utility
wall outlet. The EPS is designed, through the use of automatic voltage regulation, to continuously supply
connected equipment with stable, 220 output voltage. In the event of a complete power loss, severe
brownout or over-voltage the EPS will rely on its external battery to supply consistent 220 output voltage.
The Input Voltage Meter can be used as a diagnostic tool to identify poor quality input power.
2. OUTPUT VOLTAGE Meter: This meter measures, the AC voltage that the EPS is providing to the
computer. It displays normal line mode, AVR mode, and battery backup mode.
3. NORMAL MODE Icon: This icon will illuminate when the EPS is working under normal conditions.
4. ON BAT (On Battery) Icon: When a severe brownout or blackout, this icon appearing and an alarm
(two short beeps) activated indicate that the EPS is working via its batteries. Once the batteries are
running out of power, for a period of time, an alarm (two short beeps) will appear continuously. If this
occurs, it is recommended that save your files and turn off your equipment manually as soon as possible.
5. SILENT MODE Icon: This icon appearing indicates that the buzzer does not beep in the silent mode
until the low battery capacity.
6. OVER LOAD Icon: This icon appearing and an alarm activated indicate that the overload condition. To
relieve the overload, unplug your equipment from the EPS outlets until the icon disappears and the alarm
stops being activated.
7. LOAD CAPACITY: Load CAPACITY is also shown on the bar chart; equal 25% load capacity for each
segment.
8. BATTERY VOLTAGE: BATT. VOLTAGE indicates the voltage of battery.
7
Copyright © 2010 CyberPower Systems, Inc.
CPS600E
EPS STATUS INQUIRY AND FUNCTIONS SETUP
GENERAL MODE
a. Press the “Display” button to check the status of the EPS
Items
Unit
Input Voltage
Output Voltage
V
V
Load Capacity
Battery Voltage
%
V
b. Press and hold the Display toggle for 4 seconds.
If the machine is in the Battery Mode, it enters the silent mode. Press again for 4 seconds and it
will return to normal (buzzer) mode.
If the machine is in the Line Mode, it proceeds to Self Test.
c. If the Display toggle remains untouched for over 30 seconds, the LCD backlight will turn off
automatically.
SET-UP MODE
Step 1: Hold the Display toggle for 10 seconds to enter the EPS set-up Mode. LCD icon 1, 2 lights
indicate Set-Up Mode.
Step 2: By pressing the Display toggle, users can switch between setup functions. User configurable
functions are as follows:
a.
Delay Time: The time delay between switching from Battery Mode to Line Mode. There are 9
different settings. The default setting is 0 minute.
Function description: The machine will switch from Battery Mode to Line Mode after the AC
power transmission reaches stability within the preset delay time.
b.
Charging Current: The function adjusts the battery charging current according to the capacity of
the connected batteries. It can be configured for 25, 50, 75, and 100%. The default setting is
100%. 100% indicates that charging current is about 10Amps.
c.
Nominal Output Voltage: Configures the correct electricity/voltage supplied in the area/country
where the EPS will be used. 220V and 230V may be selected. The system default setting is
220V.
Function description: AVR Dynamic Voltage Compensation works automatically based on the
system voltage settings.
d.
Static Frequency Tolerance: There are 6 settings (1,2,4,6,8,10%), and the default setting is
+/-10%.
Copyright © 2010 CyberPower Systems, Inc.
8
CPS600E
Function description: The settings may be adjusted to the quality of the electricity in use.
e.
Slew Rate: Also called Dynamic Frequency Tolerance. There are 5 different settings
(0.25,0.5,1,2,4 Hz/Sec). The default value is 4Hz/sec.
Function description: “Slew Rate” indicates the tolerance of a device in accepting frequency
variances. The lower “Slew Rate” results in less tolerance but better protection for the connected
loads.
f.
Low Battery Shutdown Voltage: This function adjusts the EPS shutdown point according to the
battery voltage. The default setting is 10V (with load).
g.
Mode Select: The standard mode (setting: 2) and the robust mode (setting: 1) are provided to
select. Using the generators is suggested to select the robust mode (setting: 1), and using the
computers is suggested to select the standard mode (setting: 2).
The settable items are sorted by unit as in the following table:
Items
Unit
Delay Time
Charging Current
Min
%
Icon Lit
ON BAT
ON BAT
Nominal Output Voltage
Static Frequency Tolerance
V
%
NORMAL MODE
NORMAL MODE
Slew Rate
Low Battery Shutdown Voltage
%
V
None
ON BAT
Mode Select
None
None
Step 3: Press and hold the toggle for 4 seconds. When the icons blink, the value of each item can be
changed by slightly pressing the toggle.
Step 4: To save the value and return to general mode, press and hold the toggle for 4 seconds.
Note: If the machine is left idle for over 30 seconds during setup, it will turn off the backlight
and return to general mode automatically.
Note: If user wants to return to general mode without saving changes, there are two methods:
1. Wait for the backlight to turn off
2. Press and hold the “Display” toggle for 10 seconds
9
Copyright © 2010 CyberPower Systems, Inc.
CPS600E
FAULT WARNING DISPLAY AND ALARM
1.
2.
3.
4.
5.
Overheat Protection: The EPS output will be interrupted. After 30 seconds, the machine shuts
down and the LCD display output voltage is zero.
Over-Load Protection:
:The EPS output will be interrupted. After 30 seconds, the machine shuts
down and Over Load Icon lights on the LCD display.
Battery Missing:
:You should hear a long beep and Battery Indicator flashes。
Low Battery Protection: The EPS output will be interrupted. After 30 seconds, the machine shuts
down and the LCD display output voltage is zero.
The following table shows each corresponding warning message on the LCD display and the alarm
reacts during the machine shut down:
LCD
Warning
Display
Over Load Icon
Alarm
Constant tone
Condition
Over Load Output-Off - Load
exceed the rating of EPS.
High Temperature Output-Off
Zero Output
Voltage
Can Not Start Up
Constant tone
None
Solution
Check total load to
confirm the rating of
EPS.
Check fans function and
air vent clearances.
Low Battery Output-Off
-- Insufficient battery capacity.
Recharge the battery.
Over Charge or AVR Error-In Line Mode, battery is
overcharged or AVR is faulty.
Inform service agents.
Short Output-Off -- Output
Short Circuit Protection
Check the EPS output
to see if there is a short
circuit.
Line Input/ Output Error
Output-Off -- incorrect Input/
Output connection
Cold Start Battery High
Voltage Output-Off -- the
battery voltage is too high
during cold start.
Copyright © 2010 CyberPower Systems, Inc.
Check Input/
connection.
Output
Check the reason for
battery over-voltage.
10
CPS600E
TROUBLESHOOTING
Problem
Possible Cause
Input fuse is blown due to
overload.
Outlet does not provide
power to equipment.
DC fuse is blown due to
overload.
Batteries are discharged.
Unit has been damaged
by a surge or spike.
The EPS does not
perform expected runtime.
The EPS will not turn on.
Batteries are not fully
charged.
Batteries are degraded.
The on/off switch is
designed to prevent the
damage that rapidly turns
it off and on.
The unit is not connected
to an AC outlet.
The battery is worn out.
Mechanical problem.
11
Solution
Turn the EPS off and unplug the
connected equipment. Unplug the
power cord of the EPS then remove
the fuse compartment beneath the
AC inlet of the EPS and replace the
blown fuse with a spare one. Lock
the compartment back to the EPS.
Connect power cord then turn the
EPS on. Make sure that your spare
fuse meets the specification and the
equipment plugged into the outlet
does not exceed the UPS unit’s rated
capacity.
Servicing of the DC fuse should only
be performed by trained personnel.
For more information on DC fuse
replacement, contact CyberPower
Systems at
service@cyberpower-eu.com
Recharge the unit for at least 4
hours.
Contact CyberPower Systems about
replacement batteries at
service@cyberpower-eu.com
Recharge the battery by leaving the
EPS plugged in.
Contact CyberPower Systems about
replacement batteries at
service@cyberpower-eu.com
Turn the EPS off. Wait 10 seconds
and then turn the EPS on.
The unit must be connected to a
220/230V outlet.
Contact CyberPower Systems about
replacement batteries at
service@cyberpower-eu.com
Contact CyberPower Systems via
phone or visit our website at
eu.cyberpowersystems.com
Copyright © 2010 CyberPower Systems, Inc.
CPS600E
TECHNICAL SPECIFICATIONS
Model
Capacity (VA)
Capacity (Watts)
Operation Technology
CPS600E
600VA
420W
AVR ( Single Boost & Single Buck )
AC Input
Input Voltage Range
Input Frequency Range
AC Output
Number of Phase
On Battery Typical Output Voltage
Nominal Output Voltage Configuration
Note
On Battery Output Frequency
Overload Protection
Transfer Time
170Vac – 270Vac
45~65Hz (auto sensing)
Single Phase
0 ~40% LOAD Pure Sine Wave at 220Vac +/- 5%
40~100% LOAD Trapezoidal Wave at 220Vac+/- 5%
Configurable for 220 / 230Vac
50 / 60 Hz +/- 1%
On Utility: Fuse
On Battery: Internal Current Limiting
< 10 ms ( Typical )
Output Receptacles
External Battery
Schuko Type * 1
Voltage x Recommended Rating x Quantity
External Battery Rating
12V x 100Ah x 1
12V
External Battery Type
Sealed Maintenance Free Lead Acid Battery
External Battery Protection
Status Indication
Indicators
Audible Alarms
Environmental
Fuse
Power On, LCD Display
On Battery, Low Battery, Overload
Operating Temperature
Operating Relative Humidity
32°F to 104°F ( 0°C to 40°C )
0 to 90% Non-Condensing
Physical
Dimensions (L*W*H)( mm )
240 * 162 * 90
Weight (Kg)
Agency
4.1
Certificated
CE, SONCAP
Copyright © 2010 CyberPower Systems, Inc.
12
CPS600E
13
Copyright © 2010 CyberPower Systems, Inc.
CPS600E
Copyright © 2010 CyberPower Systems, Inc.
14
CPS600E
For more information, contact us at:
CyberPower Europe
CyberPower Systems B.V.
Flight Forum 3545, 5657DW Eindhoven, The Netherlands
Tel: +31 (0)40 2348170
Fax: +31 (0)40 2340314
Website: http://eu.cyberpowersystems.com/
E-mail: sales@cyberpower-eu.com
Entire contents copyright © 2010 CyberPower Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is prohibited.
15
Copyright © 2010 CyberPower Systems, Inc.