OPERATION MANUAL
OFFICE PRO 36
READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT INSTALLATION AND USAGE, AND READ ALL SAFEGUARDS.
DENSO SALES CALIFORNIA, INC.
3900 Via Oro Avenue
Long Beach CA 90810-1868
800-264-9573 / 310-834-6352
www.movincool.com
DSCA P/N: LA484007-1810
First Issue: March 2005
Printed in the U.S.A.
C
UL
US LISTED
LIMITED WARRANTY
DENSO SALES CALIFORNIA, INC. (“DENSO”) warrants its MOVINCOOL
Products only to the extent stated in its official written warranties. Unless
otherwise specifically provided in writing by DENSO, DENSO warrants to enduser that the Products shall be free of defects in materials or workmanship and
will function in accordance with DENSO’s published specifications under ordinary
intended use and service for a period of twelve (12) months after delivery to the
end-user; provided, however, in the case of the compressor element of the Products
such warranty shall be for a period of thirty six (36) months after delivery to the
end-user. DENSO shall, at its sole option, repair or replace any defective Product
covered by this warranty. Such remedy shall be end-user’s sole remedy with
respect to any particular defect in the Products.
This warranty does not cover defects or malfunctions which result from causes
beyond DENSO’s control, including, without limitation, (i) unusual physical or
electrical stress; (ii) accident, neglect, abuse, misuse or other abnormal use; (iii)
failure to perform routine maintenance in accordance with DENSO’S recommended
procedures; (iv) normal wear and tear; (v) repairs or attempted repairs by an
unauthorized person; (vi) modifications or alterations to the Products; (vii) use
with supplies or devices not supplied or approved by DENSO; or (viii) improper
servicing. This warranty shall extend only to the original end-user and shall be
void if any labels or other identifying marks permanently affixed to Products when
shipped by DENSO are removed, altered, defaced or obliterated.
The aforesaid warranty is the only warranty made by DENSO with respect to the
Products and is in lieu of all obligations or liabilities on the part of DENSO for
damages arising out of or in connection with the sale, use or performance of the
Products, including, without limitation, any lost profits or any other consequential, incidental, special or exemplary damages of any kind. DENSO DISCLAIMS
ALL OTHER WARRANTIES WITH REGARD TO THE PRODUCTS, INCLUDING
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
CONTAINED HEREIN.
PURCHASE DATE: ______________________________________________________
© 2005 DENSO SALES CALIFORNIA, INC.
All rights reserved. This book may not be reproduced or copied,
in whole or in part, without the written permission of the publisher.
DENSO SALES CALIFORNIA, INC. reserves the right to make changes
without prior notice. MovinCool is a registerd trademark of
DENSO Corporation.
SERIAL NUMBER: ______________________________________________________
TABLE OF CONTENTS
FOREWORD ............................................................................................ 1
Definition of Terms ........................................................................... 1
GENERAL WARNINGS & CAUTIONS .................................................... 1
INVENTORY ............................................................................................. 2
INSTALLATION ........................................................................................ 2
Choosing an Installation Site .......................................................... 2
Moving the Unit ................................................................................ 3
Plugging in the Unit ......................................................................... 3
FEATURES ............................................................................................... 4
OPERATION ............................................................................................ 4
Control Panel .................................................................................... 4
Operating in COOL Mode ................................................................ 5
Operating in Fan Only Mode .......................................................... 5
Changing from Fan Only Mode to COOL Mode ........................... 5
How to Set a Program ..................................................................... 6
Operating Modes ............................................................................. 7
Emptying the Drain Tank (If equipped) ........................................... 7
Drain Pump ....................................................................................... 8
DAILY INSPECTION & MAINTENANCE ................................................. 8
Emptying the Drain Tank ................................................................. 8
Cleaning the Air Filters .................................................................... 8
FIlter Removal Method ................................................................... 8
Cleaning Method .............................................................................. 9
In-Season/Off-Season Inspection & Maintenance ....................... 9
TROUBLESHOOTING ............................................................................. 9
Office Pro 36 Self-Diagnostic Codes ............................................. 9
AFCI Power Cord ........................................................................... 10
TECHNICAL SPECIFICATIONS ............................................................ 11
FOREWORD
Congratulations on purchasing the MovinCool portable air conditioner.
This manual explains how to assemble, install and operate the MovinCool Office Pro 36
portable air conditioning unit. Please read this operation manual thoroughly to familiarize
yourself with the features of the unit and to ensure years of reliable operation. You may
also find it useful to keep this operation manual on hand for reference.
Components and/or procedures are subject to change without prior notice.
Definition of Terms
WARNING: Describes precautions that should be observed in order to prevent
injury to the user during installation or unit operation.
CAUTION: Describes precautions that should be observed in order to prevent
damage to the unit or its components, which may occur during installation or unit
operation if sufficient care is not taken.
NOTE: Provides additional information that facilitates installation or unit operation.
GENERAL WARNINGS & CAUTIONS
•
•
•
•
•
•
All electrical work, if necessary, should only be performed by qualified electrical
personnel. Repair to electrical components by non-certified technicians may result in
personal injury and/or damage to the unit. All electrical components replaced must
be genuine MovinCool parts, purchased from an authorized reseller.
The proper electrical outlet for MovinCool units must be equipped with a UL approved ground-fault breaker to prevent electrical shock from the unit.
The Office Pro 36 is equipped with a six (6) foot (1.8 meter) AFCI power cord. If
replacement, fixed location (hard wired) or power cord lengthening (extension cord)
cords are required, contact your reseller or a qualified licensed electrician for approved replacement methods.
Never fold, or place heavy objects on the power cord. This could result in damage to
the power cord causing electrical shock or fire.
Do not place water or any other liquid on the unit. This can cause damage to the unit
and increase the risk of electrical shock.
Do not sit or stand on the unit.
1
INVENTORY
After unpacking your MovinCool unit, please check to make sure you have the following
items:
•
Office Pro 36 MovinCool Unit (1)
•
Operation Manual/Warranty Card (1)
NOTE: If any of these items were not included in the box or appear damaged, please
contact your MovinCool reseller for replacement.
36
OPERATION MANUAL/
WARRANTY CARD
INSTALLATION
Choosing an Installation Site
CAUTION: Following are some precautions to consider before choosing your installation site. Please review carefully as improper installation may result in personal
injury or damage to the unit.
•
•
•
•
•
•
•
•
Do not use the unit in areas where leakage of flammable gas may occur.
Do not use the unit in areas where it will be exposed to rain or water.
Do not use the unit in an atmosphere of excessively corrosive gas or vapor.
Do not use in areas where the temperature is outside the allowable operating range.
Do not install the unit in sloping areas. The unit may move or topple over even if the
casters are set to the LOCKED position.
Install the unit in areas that can withstand the weight of the unit. The Office Pro 36
weighs approximately 440 lbs (200 kg).
Allow 24 inches (610 mm) of unobstructed airflow for both air inlets and outlets.
Do not use the unit above the following conditions: 95˚ F (35 ˚C)
2
Moving the Unit
Unlock the casters and push the MovinCool unit, using the side handles, to a flat, level
surface and set the casters back to the LOCKED position.
FRONT AND BACK HANDLES
UNLOCKED
LOCKED
Plugging in the Unit
•
Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt
are present, wipe off with a clean, dry cloth.
•
Check the power cord, plug and prongs for damage or excess play. If any damage or
excess play is found, contact your MovinCool reseller for repair.
•
Fully insert plug into the A/C outlet.
WARNING:
•
If the power cord or plug is damaged, repair should only be performed by qualified electrical personnel.
•
Do not connect/disconnect the power cord or attempt to operate buttons with
wet hands. This could result in electrical shock.
CAUTION: The AC outlet (208/230 VAC Single Phase, 60Hz) needs to be rated at
30A or higher. Do not share the outlet with any other instrument or equipment.
NOTE:
•
•
Make sure the AC outlet is free of dirt, dust, oil, water, or any other foreign matter.
The Office Pro 36 model is equipped with an approved NEMA plug configuration
(6-30). The appropriate outlet must be used for this plug type.
3
FEATURES
OP36 Features
•
•
•
•
•
•
•
•
An electronic control panel which allows the user to control the unit’s operation easily.
Dual fan speeds (either High or Low) in both COOL and Fan Only modes.
A digital display that indicates the Temperature SET POINT (either Fahrenheit or
Celsius) in which the COOL Mode will operate. This is also the temperature the unit
will try to maintain. The Temperature SET POINT can be adjusted by the SET TEMP
buttons (▼/▲). (65ºF-95ºF)
A condensate drain TANK FULL indicator display (LED).
An automatic restart feature when the power is lost and regained. The unit will return
to the operating mode it was in prior to the loss of power. Any preset program will be
retained in the memory in the event power loss occurs.
A programmable Clock/Timer function. This allows the user to program a specific
time of day that the unit will begin to
operate/start and turn off/end.
A 2-digit room temperature display.
Two condensate tanks with condensate float
OPERATION
Control Panel
Before operating the unit, it is important to familiarize yourself with the basic controls
located on the control panel.
1.
2.
3.
4.
5.
6.
COOL ON/OFF Button - Activates/deactivates
the COOL mode/turns the unit off.
FAN ON/OFF Buttons - Activates/deactivates
the HIGH or LOW fan mode.
SET TEMP Buttons (▼/▲) - Increases/decreases the temperature set point.
TANK FULL LED - Flashes when the drain tank
T
is full.
SET POINT Display - Indicates the current temperature set point; also used to display clock
hour when programming.
ROOM TEMP Display - Indicates the current
room temperature; also used to display the
clock minutes when programming.
4
7
7.
Temperature Scale LED - Illuminates to indicate
the current temperatures being displayed are
either in °C or °F; also used to display the clock
when programming.
8. AM/PM LED - Illuminates to indicate AM or PM
time of day.
9. Program RUN Button - Activates/deactivates a
program.
10. Program SET Button - Allows the user to program the unit or check the current program.
11. START TIME LED, END TIME LED, SET
CLOCK LED - Illuminates to indicate the current step that is being programmed into the
unit.
8
SET TEMP
CLOCK/TIMER
HRS
MIN
12
FAN ON/OFF
START TIME
END TIME
11
SET CLOCK
SET
COOL ON/OFF
RUN
PROGRAM
9
10
Office Pro 36
12. CLOCK/TIMER Buttons - Allows the user to set the clock and program the start and
end time of operation.
Operating in COOL Mode
➀
The unit can be operated in COOL mode by pressing the COOL
ON/OFF button (LED illuminates).
NOTE: In COOL mode the unit can only be turned off by pressing the “COOL ON/
OFF” button again, not by pressing the fan buttons.
➁
Change the fan speed by pressing the HIGH or LOW fan buttons.
➂
Change the temperature set point by pressing the SET TEMP buttons (▼/▲).
NOTE: When turning the unit on, the set point and fan speed are determined by the
last operating mode (program mode not included).
Operating in Fan Only Mode
➀
The unit can also be operated in Fan Only mode by pressing either the HIGH or LOW
fan buttons (LED illuminates).
➁
The unit can then be turned off by pressing the fan speed button that is illuminated.
Changing from Fan Only Mode to COOL Mode
➀
The COOL mode can be activated while the unit is operating in Fan Only mode. To do
this, simply press the COOL ON/OFF button (LED illuminates).
NOTE: The Fan Only mode will not operate after the COOL mode has been activated.
After the COOL mode has been activated, the unit cannot be turned off by pressing
the fan buttons. The COOL ON/O
N FF button must be pressed.
N/O
5
How to Set a Program
➀
Setting a START TIME
Press the Program SET button. The Program SET button and START TIME LEDs will
illuminate. Press the HRS and MIN buttons to set the START TIME.
➁
Setting an END TIME
Press the Program SET button until the END TIME LED illuminates. Press the HRS
and MIN buttons to set the END TIME.
➂
Setting the CLOCK TIME
Press the Program SET button until the SET
ET CLOCK LED illuminates. Press the HRS
and MIN buttons to set the current clock time into the unit.
NOTE: The AM/PM LED will change with the HRS button.
➃
Programming the Temperature SET POINT
Press the Program SET button until the current SET POINT temperature display
begins to flash on and off. Select a new desired SET POINT temperature by pressing
the SET TEMP buttons (▼/▲).
➄
Programming the Fan Speed
Press the Program SET button until one of the Fan Speed button LEDs (High/Low)
begin to flash. This is the current programmed Fan Speed. To change the programmed Fan Speed, simply press the other Fan Speed button.
➅
Exiting the Program SET Function
After changing any of the above settings, continue pressing
the Program SET
button until the Program SET button LED turns off. The unit will then return to the
previous mode.
➆
Activating/Deactivating a Preset Program
Press the Program RUN button to activate/deactivate a preset program. The Program
RUN LED will illuminate when activated.
NOTE:
•
The unit will return to the previous mode if a program is turned off while it is
running.
•
The Program RUN LED flashes while a program is running. It is illuminated continuously when the program mode is activated.
•
While a program is running, the program can only be stopped by pressing the
Program RUN button. All other buttons are inoperable when a program is running.
•
The unit returns to the previous mode at the end of a program.
•
The unit does not have to be running to set a program.
•
During programming, the unit returns to the previous mode if no activity occurs
within approximately 35 seconds.
6
Operating Modes
Office Pro 36 operates in 2 modes, FAN Only and COOL. When in FAN Only mode, the unit
circulates the surrounding air. When in COOL mode, the compressor is operational and
cool air is circulated.
•
COOL Mode
Office Pro 36 will operate in FAN Only mode for approximately 120 seconds before
the compressor engages. (Time delay setting is 120 ±15 seconds.)
•
Temperature Control
•
The room temperature thermistor allows the unit to switch automatically between
COOL and FAN Only modes. This is dependent upon inlet air temperature versus SET
POINT temperature.
Fan Mode Control DIP Switch
•
The Fan Mode Control DIP Switch determines whether the FAN will continue to operate or stop when the compressor cycles off. (SET POINT temperature equals inlet
air or room temperature.) The unit has been preset at the factory for continuous fan
operation.
Temperature Scale Display DIP Switch
The Temperature Scale Display DIP Switch changes the temperature(s) that are
displayed to either °C or °F. The unit has been preset from the factory to display the
temperature(s) in °F.
NOTE: If you wish to change the fan mode operation (COOL[OPERATE to
COOL[STOP), and/or the Temperature Scale Display (°F to °C), contact your MovinCool reseller.
Emptying the Drain Tank (If equipped)
During COOL mode, condensate will accumulate in the drain tank. When the drain tank
becomes full, the FULL TANK LED will flash and the unit will shut off automatically.
NOTE: If you want to empty the drain tank, while the unit is in operation, press the
COOL ON/OFF button to turn the unit off. If a program is running, you must first press the Program
RUN button.
➀
Open the front panel.
➁
Pull the drain tank from the unit.
➂
Remove the cap and empty the drain tank.
➃
Replace the cap and return the drain tank to the
unit.
➄
Close the drain tank lid.
➅
If the Program RUN LED is flashing, press the
COOL ON/OFF button to continue running the
program. If the Program RUN LED is illuminated
continuously, no further steps are necessary. If
no program exists or the program was deactivated, press the COOL ON/OFF button to restart
the unit.
7
Drain Pump (Optional)
A drain pump allows continuous operation and eliminates the need for drain tanks.
•
When the water collects to level (A) in the pump
reservoir, the drain pump begins to operate and
discharges the water.
•
When the water level drops below level (B), the
drain pump will stop.
NOTE:
•
If for any reason the water level exceeds that
of level (A) in the pump reservoir, an overflow
Drain Switch will stop the compressor operation.
•
If the Fan Mode Control DIP Switch (see pg.5)
has been set operate from the STOP position,
the Fan will also turn off while the drain pump
is discharging water.
A
B
DAILY INSPECTION & MAINTENANCE
Emptying the Drain Tank
To empty the drain tank, refer to instructions, page 14.
Cleaning the Air Filters
Clean the air filters once a week. If the unit is used in a dusty environment, more frequent
cleaning may be required.
A dirty air filter reduces air output resulting in a decrease of the cooling capacity.
Filter Removal Method
Turn the unit off, by pressing the COOL ON/OFF button. If a program is running, you
must first press the Program RUN button.
➁ Remove the 2 air filters.
NOTE: To remove the filters from the Office Pro 36, open the front panel and side
panel filter doors. Unclip the wire frame and remove filter.
➀
VELCRO®
ATTACHMENTS
CLIP
FILTER
WIRE FRAME
CLIP
FILTER
8
Cleaning Method
➀
Remove dust from the element with a vacuum cleaner, or rinse in cold or lukewarm
water. If the element is extremely dirty, wash
FILTER
with a neutral detergent.
➁
After the element has been cleaned, rinse with
clean running water, allow to dry, then reinstall.
In-Season/Off-Season Inspection & Maintenance
■
In-Season
■
Check the prongs and surface of the power cord plug for dust and/or dirt. If dust
and/or dirt are present, wipe off with a clean, dry cloth.
➁ Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is found, contact your MovinCool reseller for repair.
➂ Check the air filters and drain tank.
➃ Clean the outside of the unit(s) with a damp cloth or mild nonabrasive cleaner.
Off-Season
➀
➀ Operate the unit in Fan Only mode for 8 hours.
Note: Operation is necessary to dry out the inside of the unit.
➁
➂
➃
➄
➅
Disconnect the power cord from the AC outlet.
Check the prongs and surface of the power cord plug for dust and/or dirt. If dust
and/or dirt are present, wipe off with a clean, dry cloth.
Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is found, contact your MovinCool reseller for repair.
Clean the air filters.
Empty all water from the drain tank.
TROUBLESHOOTING
Office Pro 36 Self-Diagnostic Codes
Self-Diagnostic Codes will be displayed on the Control Board under the following
conditions:
dF
When the evaporator freezestat disengages the
compressor.
FL
When the drain tank switch shuts off the unit (FULL
TANK LED flashes).
AS
When unit disengages the compressor while the
condensate pump is discharging water.
HP
When the high pressure switch disengages the
compressor.
LO
Lowest temperature set point.
Note: If AS does not disappear from display, contact your distributor.
9
Check the following points before calling a qualified technician.
SYMPTOM
POSSIBLE CAUSE
REMEDY
Unit does not operate
➀ Ground fault breaker tripped
➁ Drain tank is full
Reset breaker
Empty the drain tank
(FULL TANK LED will be
(FULL
flashing)
Insufficient cooling
➀ Dirty/blocked air filters
➁ Air inlet/outlet blocked
➂ Improper temperature setting
Clean air filters
Clear air inlet/outlet
Set to desired position
If symptoms persist after the above actions have been taken, turn the unit off, disconnect
the power cord plug and contact your MovinCool reseller.
AFCI Power Cord Manual
WARNING: The AFCI device is a non-serviceable part. Attempting to open the
device may expose the user to hazardous electric shock, and voids any warranties
and performance claims. Manufacturer’s liability is limited to the replacement of the
device.
CAUTION:
1.
2.
3.
4.
5.
6.
Read manual for proper use and handling of this device.
Press “RESET” button before starting the A/C unit. Press “TEST” to check function then “RESET” again. Start the A/C unit.
Do not immerse in water
This device must only be plugged on appropriate wall outlet.
In the event that this device trip, the cause of the malfunction should be corrected first before further use.
Using the device beyond recommended voltage poses risk to users.
10
TECHNICAL SPECIFICATIONS
ITEM/FEATURES
OFFICE PRO 36
Rating Conditions
dry bulb
wet bulb
humidity
95º F (35º C)
83º F (28.2º C)
60%
Specifications
power frequency
line voltage
power consumption
current consumption
power factor
starting current
power wiring
60Hz
single phase 208/230V
4.4 Kw
19.7 Amps
99%
88A
10 (3-core) AWG
Cooling Unit
cooling capability
9,070 Kcal/hr
36,000 BTU/hr
direct expansion
cooling system
Blower
type of fan
air volume:
motor output:
centrifugal fan
999 ft 3/min (1682 m3/h)
825 ft 3/min (1402 m3/h)
1490 ft3/min (2532 m3/h)
1060 ft3/min (1801 m3/h)
0.21 Kw
0.33 Kw
evaporator (high speed)
evaporator (low speed)
condenser (high speed)
evaporator (low speed)
evaporator (high)
condenser (high)
Compressor
type
output
refrigerant type
refrigerant capacity
hermetic scroll
2.1 Kw
R-22
2.4 lbs (3.1 kg)
Safety Devices
compressor overload protector
fan motor protector
anti-freezing thermistor
full drain tank switch
automatic restart (power interruption)
compressor time delay program
included
included
included
included
included
included
Dimensions & Weight
W x D x H (in)
W x D x H (mm)
weight (lbs/kg)
30” x 44” x 52”
760 x 1117.6 x 1321
540/245
Operating Conditions
inlet air (relative humidity)
95º F (35º C), ≤ 60%
65º F (18.3º C), ≥ 50%
Control Device
temperature control
programmable timer
two speed fan
included
included
included
11
LIMITED WARRANTY
DENSO SALES CALIFORNIA, INC. (“DENSO”) warrants its MOVINCOOL
Products only to the extent stated in its official written warranties. Unless
otherwise specifically provided in writing by DENSO, DENSO warrants to enduser that the Products shall be free of defects in materials or workmanship and
will function in accordance with DENSO’s published specifications under ordinary
intended use and service for a period of twelve (12) months after delivery to the
end-user; provided, however, in the case of the compressor element of the Products
such warranty shall be for a period of thirty six (36) months after delivery to the
end-user. DENSO shall, at its sole option, repair or replace any defective Product
covered by this warranty. Such remedy shall be end-user’s sole remedy with
respect to any particular defect in the Products.
This warranty does not cover defects or malfunctions which result from causes
beyond DENSO’s control, including, without limitation, (i) unusual physical or
electrical stress; (ii) accident, neglect, abuse, misuse or other abnormal use; (iii)
failure to perform routine maintenance in accordance with DENSO’S recommended
procedures; (iv) normal wear and tear; (v) repairs or attempted repairs by an
unauthorized person; (vi) modifications or alterations to the Products; (vii) use
with supplies or devices not supplied or approved by DENSO; or (viii) improper
servicing. This warranty shall extend only to the original end-user and shall be
void if any labels or other identifying marks permanently affixed to Products when
shipped by DENSO are removed, altered, defaced or obliterated.
The aforesaid warranty is the only warranty made by DENSO with respect to the
Products and is in lieu of all obligations or liabilities on the part of DENSO for
damages arising out of or in connection with the sale, use or performance of the
Products, including, without limitation, any lost profits or any other consequential, incidental, special or exemplary damages of any kind. DENSO DISCLAIMS
ALL OTHER WARRANTIES WITH REGARD TO THE PRODUCTS, INCLUDING
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
CONTAINED HEREIN.
PURCHASE DATE: ______________________________________________________
© 2005 DENSO SALES CALIFORNIA, INC.
All rights reserved. This book may not be reproduced or copied,
in whole or in part, without the written permission of the publisher.
DENSO SALES CALIFORNIA, INC. reserves the right to make changes
without prior notice. MovinCool is a registerd trademark of
DENSO Corporation.
SERIAL NUMBER: ______________________________________________________
OPERATION MANUAL
OFFICE PRO 36
READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT INSTALLATION AND USAGE, AND READ ALL SAFEGUARDS.
DENSO SALES CALIFORNIA, INC.
3900 Via Oro Avenue
Long Beach CA 90810-1868
800-264-9573 / 310-834-6352
www.movincool.com
DSCA P/N: LA484007-1810
First Issue: March 2005
Printed in the U.S.A.
C
UL
US LISTED