AllTrade COMPONENT #690551-1HR Instruction manual

COMPONENT
#690551-1HR
19.2V 2-SPEED BATTERY-OPERATED DRILL
INSTRUCTION MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
PARA EL SERVICIO
PARA EL CONSUMIDOR
1-800-590-3723
Printed in China
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
690551 – 19.2V Green Cordless Drill_Rev 8/26/06
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM.
YOUR FEEDBACK IS VITAL TO US.
TABLE OF CONTENTS
CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INTENDED USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION ONE
GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS . . 2
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WORK AREA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ELECTRICAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PERSONAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
TOOL USE AND CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SECTION TWO
SPECIFIC SAFETY RULES AND/OR SYMBOLS . . . . . . . . . . . . . . . . . . . 6
SAFETY RULES FOR CORDLESS DRILL/DRIVERS . . . . . . . . . . . . . 6-7
SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SECTION THREE
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
REMOVING/ATTACHING BATTERY PACK . . . . . . . . . . . . . . . . . . . . 10
CHARGER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CHARGING BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
INSTALLING DRILL BIT INTO KEYLESS CHUCK . . . . . . . . . . . . . . 12
OPERATING THE CORDLESS DRILL . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-15
VARIABLE SPEED TRIGGER SWITCH . . . . . . . . . . . . . . . . . . . . . . . 13
FORWARD / REVERSE AND TRIGGER LOCK LEVER . . . . . . . . . . . . 13
TORQUE SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
HIGH/LOW SPEED (GEAR) SHIFTING . . . . . . . . . . . . . . . . . . . . . . 14
SCREWDRIVING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DRILLING METAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DRILLING MASONRY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DRILLING WOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HINTS FOR OPTIMUM USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
1
SECTION FOUR
MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PROTECTING THE ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS . . . . . . . . . . . . . . 18
SECTION FIVE
3 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-22
CONGRATULATIONS!
Thanks for choosing this product. At Alltrade, our aim is to provide you with quality
products at an affordable price, and we want you to be totally satisfied with your
product and our Customer Service. If any help and advice is needed, please
contact us at 1-800-590-3723. Properly cared for, this tool will give you many
years of satisfaction.
INTENDED USE
This tool is intended for consumer use only. Your charger and/or adapter has been
designed for charging batteries of the type approved and supplied with this tool.
GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to
follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.
Always use common sense and pay particular attention to all the DANGER,
WARNING, CAUTION and NOTE statements of this manual.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
2
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WORK AREA
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Keep your work area clean and well lit. Cluttered work benches and dark work
areas may cause accidents or injury.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
IMPORTANT SAFEGUARDS
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
A battery operated tool with integral batteries or a separate battery pack
must be recharged only with the specified charger for the battery. A charger
that may be suitable for one type of battery may create a risk of fire when used with
another battery.
Use battery operated tool only with specifically designated battery pack. Use of
any other batteries may create risk of fire.
PERSONAL SAFETY
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry or long hair can be caught in moving parts.
WARNING: Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands after handling.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Avoid accidental starting. Be sure switch is in the locked or “OFF” position
before inserting battery pack. Carrying power tools with your finger on the switch
or inserting battery pack into a tool with the power switch “ON” invites accidents.
4
SERVICE
Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a
key that is left attached to a rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
Use clamps or other practical ways to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
Tool service must be performed only by qualified repair personnel. Service or
maintenance by unqualified personnel may result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact
with a “live” wire will also make exposed metal parts of the tool “live” and shock
the operator.
SAFETY RULES FOR CORDLESS DRILL / DRIVERS
Do not force tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that
cannot be controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool or place the switch in the locked or “OFF” position before making any adjustments, changing accessories, or storing the tool.
Such preventative safety measures reduce the risk of starting the tool accidentally.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns or a fire.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with sharp cutting edge are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
5
Always wear safety goggles or eye protection when using this tool. Use a
dust mask or respirator for applications which generate dust.
Do not grasp the tool or place your hands too close to the spinning chuck or
drill bit. Your hand may be lacerated or may cause injury.
Secure the material being worked on. Never hold it in your hand or across
your legs. Unstable support can cause loss of control and injury.
Position yourself to avoid being caught between the tool or side handle and
walls or posts. Should the socket or bit become bound in the work, the
reaction torque of the tool could crush your hand or leg.
Check to see that keys and adjusting wrenches are removed from the
Cordless Drill before switching the tool “ON”. Keys or wrenches can fly away
at high velocity striking you or a bystander.
When using the Cordless Drill, always maintain a firm grip on the tool with both
hands.
Keep the handle of the Cordless Drill dry, clean, and free from oil and grease.
Do not run the Cordless Drill while carrying it at your side. A spinning
socket or bit could become entangled with clothing and injury may result.
Disconnect the plug or remove the battery pack from tool and place the switch
in the locked or “OFF” position before making any assembly adjustments,
changing accessories, performing any inspection, maintenance or cleaning
procedures. Such preventive safety measures reduce the risk of starting the
tool accidentally.
6
FUNCTIONAL DESCRIPTION
8
6
Do not use the Cordless Drill if it has been damaged, left outdoors in the
rain, snow, wet or damp environments, or immersed in liquid.
Maintain labels and nameplates on the Cordless Drill. These carry important
information. If unreadable or missing, contact Alltrade for a replacement.
10
5
12
SYMBOLS
7
3
9
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SYMBOL
V
A
Hz
W
Kg
min
s
NAME
Volts
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
Alternating or Direct Current
Earthing Terminal
Class II Construction
Minutes
Seconds
Diameter
.../min
No load speed
Revolutions per Minute
1,2,3, …
Ring Selector Settings
7
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
Type of Current
Grounding Terminal
Denotes Double Insulation
Time
Time
Size of Drill Bits,
Grinding Wheels, etc.
No-load Rotational Speed
Revolutions, Surface Speed,
Strokes, etc. per Minute
Speed, Torque or Position Settings
11
2
4
1
CONTROLS AND COMPONENTS:
1. Battery Pack
2. Release Buttons on Each Side
3. Charger
4. Indicator Lights
5. 12.7mm (1/2") Keyless Chuck
6. 22 Adjustable Torque Settings
Control Ring
7. Forward/Reversing and
Trigger Lock Lever
COMPONENT
BATTERY PACK
CHARGER
12.7mm (1/2") KEYLESS CHUCK
8. High/Low Speed Switch
9. Variable Speed Controlled
Trigger Switch
10. Accessory/Bit Holder
11. Comfort Rubber Grip
ACCESSORIES:
12. Double Ended Screwdriver Bits (2)
MODEL NUMBER
690549
690543
690552
8
BATTERY
Before using battery pack, please read carefully all instructions and cautionary markings on battery pack, battery
charger and product using battery.
®
Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode.
Do not carry battery packs in aprons, pockets, or tool
boxes, product kit boxes, drawers, etc. with loose metal objects. Battery
pack terminals could be short circuited causing damage to the battery pack,
severe burns or fire.
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency. Before disposing of damaged or worn out Ni-Cad battery packs, check with your State Environmental
Protection Agency to find out about special restrictions on the disposal of these
battery packs, take them to your local recycling center for proper disposal, or
call 1-800-822-8837.
The battery is not fully charged. Before first use, the battery pack requires
3-5 hours charge time to be fully charged. Subsequent recharging needs 1 hour
for the battery to be fully charged.
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life.
Never over-discharge a battery by using the tool even after tool performance
has decreased. Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
Charge battery pack at ambient temperatures between 50° F – 104° F.
Store tool and battery pack in locations where temperatures will not exceed
120°F. This is important to prevent serious damage to the battery cells.
The battery pack should always be recharged when the Cordless Drill begins to
run slowly.
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause sparks, burns, or fire.
REMOVING/ATTACHING BATTERY PACK
REMOVE BATTERY PACK:
1. Press both release buttons on either
side of the Cordless Drill to release
the battery pack.
2. Pull battery pack free of Cordless Drill.
ATTACH BATTERY PACK:
1. Align the raised portion of the battery
pack with the groove in the battery
compartment of the Cordless Drill.
2. Press the battery pack
into place. Make sure the
latches are securely fastened.
Do not use the Cordless
Drill if the battery pack is
not seated properly.
RELEASE BUTTON
CHARGER
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
Use only the charger which accompanied your product or direct replacement as
listed in this manual. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
Do not disassemble charger.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
The battery pack and charger heat during charging. Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
When the battery pack requires recharging, a 1 hour charge allows the tool to
operate at full power. A charging indicator light on the charger will illuminate to
show that charging is taking place.
10
CHARGING BATTERY PACK
CHARGE BATTERY PACK:
1. Plug the charger into
the nearest 120 volt
electrical outlet.
2. Make sure the trigger
on the Cordless Drill
is in the “OFF”
position and remove
the battery pack from
the Cordless Drill.
3. Insert the battery pack
into the charger. Be sure
that the battery pack is
fully seated in the charger.
Do not force.
ASSEMBLY
BATTERY PACK
Be aware that this tool is always in an operating condition
because it does not have to be plugged into an electrical outlet. Always turn
the switch “OFF” and remove the battery pack before changing bits.
INSTALLING DRILL BIT INTO KEYLESS CHUCK
LED
LIGHT
WARNING
Before inserting a drill bit or other accessory, make sure the forward/reverse
and trigger lock lever is in the center “OFF” position to prevent accidental starts
that may result in injury.
BATTERY
CHARGER
4. The red indicator light should come “ON” indicating that the battery pack is in
a “Fast Charge” mode. If the green indicator light comes “ON”, then the battery
is already fully charged.
5. After approximately one hour of charging, the red indicator light should go
“OFF” and the green light should come “ON” indicating that the battery is fully
charged and the charger is now in a “Trickle Charge” mode.
6. The battery can be left in a “Trickle Charge” mode until ready to use.
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your Cordless Drill continuously, the batteries in your battery pack
will become hot. You should let a hot battery pack cool down for approximately
30 minutes before attempting to recharge. When the battery pack becomes
discharged and is hot, the red light on the charger will flash. When the battery
pack cools down, the red light will glow continuously to indicate fast charging
mode, 1-hour charge time.
This will occur when continuous use of your Cordless
Drill causes the battery pack to become hot. It does not occur under normal
circumstances.
Do not attempt to tighten drill bits (or any other accessory) by gripping the
front of the chuck and turning the tool on. This may cause personal injury
and/or damage to the chuck.
When removing the bit from the tool, avoid contact with skin and use proper
protective gloves when grasping the bit or accessory. Accessories may be hot
after prolonged use.
1. Hold the rear end of the chuck
in one hand and use the other
hand to rotate the front end in a
counterclockwise direction to
open the jaws of the chuck.
HOLD
LOOSEN
2. Insert the shank of the bit (or
other accessory) fully into the
keyless chuck, taking care to
keep the bit in the center of
the jaws of the chuck.
TIGHTEN
3. Turn the front end of the chuck clockwise to hold the bit in place.
4. Tighten securely by turning the front end of the chuck clockwise while holding
the rear end.
OPERATING THE DRILL
Never tape the trigger switch down to provide continuous high speed. The tool may fail under such conditions causing fire or
personal injury.
12
VARIABLE SPEED TRIGGER SWITCH
THIS TOOL IS CONTROLLED
BY A TRIGGER SWITCH:
• The speed of the Cordless Drill depends
on the amount of pressure you put on the
trigger.
• The more pressure you apply, the faster
the Cordless Drill will go.
THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE:
• For light duty work, use lower settings.
CONTROL RING
• For heavy duty work, use higher settings.
PROPER SETTING FOR DRIVING SCREWS:
1. Set the ring on the lowest
setting to begin.
TRIGGER
SWITCH
• Release the pressure and the Cordless Drill
will slow down.
2. Try tightening the first screw.
If the drill drives smoothly,
proceed with the next screw.
3. If the Drill’s clutch slips,
increase the torque setting
and try again until the Drill
drives the screw without incident.
FORWARD / REVERSE AND TRIGGER LOCK LEVER
HIGH/LOW SPEED (GEAR) SHIFTING
Be sure the trigger is released when changing the position of the lever.
Always store the tool in the “LOCKED/OFF” position.
Always check the direction of the Cordless Drill's rotation before use.
TO SELECT THE DIRECTIONS
OF ROTATION:
• To select forward Cordless Drill
rotation, press the trigger lock
from left to right flat against the Cordless
Drill body.
LOW SPEED
FOR LOW SPEED SETTING:
• Slide the switch on top of the
Drill to Position 1 for high
torque applications and driving
screws.
HIGH SPEED
FOR HIGH SPEED SETTING:
• Slide the switch to Position 2
for light duty projects.
TRIGGER
LOCK
• To select reverse, press the trigger lock
lever in the opposite direction.
• The center position locks the tool.
SCREWDRIVING
TORQUE SETTINGS
WHEN DRIVING FASTENERS:
• Always start slowly and gradually increase the speed of the Drill.
• Release the trigger when you feel the clutch slip.
To prevent damaging the tool or driving screw too deep
into work piece, release the trigger when you feel the clutch slip.
13
• Always keep the driver bit straight to prevent damage to the screw.
• Hold the Drill with both hands to ensure control if the bit should stick or slip.
• To prevent wood from splitting, drill pilot holes into the wood before driving
in the screws.
14
DRILLING METAL
WHEN DRILLING HARD METALS:
• Apply a lubricant, such as cutting oil, to the tip of the bit.
• Start with a small hole then enlarge to the required size. Make sure the bit is
actually cutting and not spinning in the hole as this will dull the edges of the bit.
• Keep enough pressure on the bit to keep it drilling through the material.
DRILLING MASONRY
WHEN DRILLING MASONRY:
• Masonry can be brittle so be careful not to apply too much pressure and crack
the material.
• Apply enough pressure to keep the bit cutting and not spinning in the hole as this
will dull the edges of the bit.
• Bricks and similar soft materials will require less pressure, concrete will require
much more.
DRILLING WOOD
Use twist bits to drill holes in wood. Make sure the bits are sharp. Pull the bits
out of the hole frequently to clear chips from the flutes as an overburdened bit
may overheat.
HINTS FOR OPTIMUM USE
• Never try to start a stalled Drill by clicking the trigger switch “ON” and “OFF”.
This may damage your tool.
• To reduce jamming, always keep the Drill running when pulling the bit out of a
finished hole.
SCREWDRIVING:
• Always use the correct type and size of screwdriver bit.
• If screws are difficult to tighten, try applying a small amount of washing liquid or
soap as a lubricant.
• Always hold the tool and screwdriver bit in a straight line with the screw.
MAINTENANCE AND CLEANING
Always remove the battery pack before attempting
cleaning or maintenance.
This Cordless Drill is lubricated before it leaves the
factory. This lubrication should last for the life of the tool. No further
lubrication is required.
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
Always clean the battery pack using only a dry cloth. Do not use liquids.
DRILLING:
• Keep the right amount of pressure in a straight line with the drill bit. Too little and
the bit will spin without cutting, too much and the motor may stall.
• Just before the drill tip breaks though the other side of the work piece drill more
slowly and decrease pressure on the tool. This will prevent stalling and leave a
cleaner hole.
• Use a block of wood to back up work pieces that may splinter.
• Use spade bits when drilling large diameter holes in wood.
• Use HSS drill bits when drilling in metal.
• Use masonry bits when drilling in soft masonry.
• Use a lubricant when drilling metals other than cast iron, aluminum, copper,
and brass.
• When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent
slipping at higher speeds.
15
Always unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dry cloth.
Never open the Cordless Drill case, battery pack or charger. Do not attempt to
repair the Cordless Drill, battery pack or charger yourself. Opening any of these
parts will void your warranty.
ACCESSORIES
PROTECTING THE ENVIRONMENT
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
BATTERIES
Alltrade batteries can be recharged many times. At the end of their useful life,
recycle batteries with due care for our environment.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may experience a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
10FT.
25FT.
50FT.
100FT.
3-6
18
18
18
18
6-8
18
18
18
16
8-10
18
18
18
14
10-12
16
16
14
14
12-16
14
12
12
16-20
12
12
12
-
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
SPECIFICATIONS
Routers
Rotary Tools
SPECIFICATIONS
Voltage
Low Speed
High Speed
Torque Settings
Chuck Capacity (max)
Charger Input
Charging Time
Battery Type
19.2V
0-440/min.
0-1500/min.
21+ Drill
13mm (1/2")
120V
60Hz
Approx. 1 hour
Ni-Cad
17
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
18
3 YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ power tool and no one else all parts
of the product (except those parts referred to below which are specifically excluded from such warranty (see Exclusions)) to be free from defects in materials and
workmanship for a period of three years from original date of purchase, except that
such warranty with regard to the battery shall be for a period of two years from
original date of purchase, unless the tool is used for commercial or rental
purposes.
SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE: The above
warranty for this Kawasaki™ power tool, including the battery, shall be effective for
only 90 days from the original date of purchase if this tool is used for any
COMMERCIAL OR RENTAL PURPOSE.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any
other product and/or component thereof manufactured or distributed by Alltrade,
and does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsible for the return shipping charges. Alltrade’s repair and/or replacement of any nonconforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
19
20
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
21
22
COMPONENT
#690850-1HR
19.2V BATTERY-OPERATED
RECIPROCATING SAW
INSTRUCTION MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE
TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
PARA EL SERVICIO
PARA EL CONSUMIDOR
1-800-590-3723
Printed in China
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT.
CONSUMER INQUIRES SHOULD BE DIRECTED TO:
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
690850 – 19.2V Green Cordless Reciprocating Saw, _Rev. 10/10/06
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER
SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING
INFORMATION AVAILABLE: MODEL NO., DATE PURCHASED AND STORE LOCATION. AN
ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU
WOULD LIKE TO MAKE A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT:
INFO@ALLTRADETOOLS.COM. YOUR FEEDBACK IS VITAL TO US.
TABLE OF CONTENTS
CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INTENDED USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION ONE
GENERAL SAFETY RULES—FOR ALL BATTERY OPERATED TOOLS . . 2
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WORK AREA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ELECTRICAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PERSONAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
TOOL USE AND CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SECTION TWO
SPECIFIC SAFETY RULES AND/OR SYMBOLS . . . . . . . . . . . . . . . . . . . 6
SAFETY RULES FOR CORDLESS RECIPROCATING SAW . . . . . . . . 6-7
SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION THREE
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12
REMOVING/ATTACHING BATTERY PACK . . . . . . . . . . . . . . . . . . . . 11
CHARGER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CHARGING BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ATTACHING/REMOVING BLADE . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
OPERATING THE RECIPROCATING SAW . . . . . . . . . . . . . . . . . . . . . . . 14-17
VARIABLE SPEED TRIGGER SWITCH . . . . . . . . . . . . . . . . . . . . . . . 14
GENERAL CUTTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PLUNGE CUTTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
METAL CUTTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17
SECTION FOUR
MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PROTECTING THE ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS . . . . . . . . . . . . . . 19
S E C TI O N F I V E
3 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-22
CONGRATULATIONS!
Thanks for choosing this product. At Alltrade, our aim is to provide you with quality
products at an affordable price, and we want you to be totally satisfied with your
product and our Customer Service. If any help and advice is needed, please
contact us at 1-800-590-3723. Properly cared for, this tool will give you many
years of satisfaction.
INTENDED USE
This tool is intended for consumer use only. Your charger and/or adapter has been
designed for charging batteries of the type approved and supplied with this tool.
GENERAL SAFETY RULES—FOR ALL BATTERY OPERATED TOOLS
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to
follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.
Always use common sense and pay particular attention to all the DANGER,
WARNING, CAUTION and NOTE statements of this manual.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
2
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
WORK AREA
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Keep your work area clean and well lit. Cluttered work benches and dark work
areas may cause accidents or injury.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
IMPORTANT SAFEGUARDS
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Do not abuse the cord. Never use the cord to carr y t h e t o o l . K e e p t h e c o r d
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
i m m e d i a t e l y. Damaged cords may create a fire.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
A b a t t e r y o p e r a t e d t o o l w i t h i n t e g r a l b a t t e r i e s o r a s e p a r a t e b a t t e r y pack
must be recharged only with the specified charger for the batter y. A charger
that may be suitable for one type of battery may create a risk of fire when used with
another battery.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Use battery operated tool only with specifically designated batter y pack. Use of
any other batteries may create risk of fire.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
WARNING: Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands after handling.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
3
4
PERSONAL SAFETY
Stay alert, watch what you are doing, and use common sense when operat ing a power tool. Do not use tool while tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelr y. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry or long hair can be caught in moving parts.
Avoid accidental starting. Be sure switch is in the locked or “ O F F ” position
before inserting batter y pack. Carrying power tools with your finger on the
switch or inserting battery pack into a tool with the power switch “ O N ” invites
accidents.
Remove adjusting keys or wrenches before turning the tool “ON”. A wrench
or a key that is left attached to a rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate conditions..
When batter y pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns or a fire.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with sharp cutting edge are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
m o d e l . Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
SERVICE
Tool ser vice must be performed only by qualified repair personnel. Service or
maintenance by unqualified personnel may result in a risk of injury.
When ser v i c i n g a t o o l , u s e o n l y i d e n t i c a l r e p l a c e m e n t p a r t s . F o l l o w i n s t r u c t i o n s
in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury..
SPECIFIC SAFETY RULES AND/OR SYMBOLS
TOOL USE AND CARE
Use clamps or other practical ways to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that
cannot be controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool or place the switch in the locked or “OFF” position before making any adjustments, changing accessories, or storing the tool.
Such preventative safety measures reduce the risk of starting the tool accidentally.
Hold tool by insulated gripping surfaces when perform ing an operation where the cutting tool may contact hidden wiring. Contact
with a “live” wire will also make exposed metal parts of the tool “live” and shock
the operator.
SAFETY RULES FOR CORDLESS RECIPROCATING SAWS
Always wear safety goggles or eye protection when using this tool. Use a dust
mask or respirator for applications which generate dust.
Secure the material being worked on. Never hold it in your hand or across
your legs. Unstable support can cause loss of control and injury.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
5
6
SYMBOLS
When using the Cordless Reciprocating Saw, always maintain a firm grip on
the tool with both hands. Never put your hands or feet in the cutting area. Do
not grasp the tool or place your hands too close to the blade. Keep your hands
well away from the blade. Never reach underneath the tool while the blade is in
motion. Do not use your legs or feet to stabilize the work piece.
Position yourself to avoid being caught between the tool or side handle and
walls or posts. Should the blade become bound or jammed in the work, it could
result in loss of control and injury.
Do not run the Cordless Reciprocating Saw while carr ying it at your side. A moving blade could cause serious personal injury.
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SYMBOL
V
A
Hz
W
Kg
Disconnect batter y pack from tool and place the switch in the locked or
“OFF” position before making any assembly, adjustments, changing acces sories, performing any inspection, maintenance or cleaning procedures. Such
preventive safety measures reduce the risk of starting the tool accidentally
which could cause serious personal injury.
Do not use the Cordless Reciprocating Saw if it has been damaged, left out doors in the rain, snow, wet or damp environments, or immersed in liquid.
Do not use dull or damaged blades.
Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
SYMBOL
min
s
␾
NAME
Volts
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
Alternating or Direct Current
Earthing Terminal
Class II Construction
NAME
Minutes
Seconds
Diameter
When restarting a saw in the workpiece, check that teeth are not engaged in
the material.
.../min
No load speed
Revolutions per Minute
Keep the handle of the Cordless Reciprocating Saw dr y, clean, and free from
oil and grease.
1,2,3, …
Ring Selector Settings
Be extra careful when cutting in high or hard-to-reach locations. Be on the
lookout for hidden wires and falling debris.
Maintain labels and nameplates on the Cordless Reciprocating Saw. These
carry important information. If unreadable or missing, contact Alltrade for a
replacement.
7
8
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
Type of Current
Grounding Terminal
Denotes Double Insulation
EXPLANATION
Time
Time
Size of Drill Bits,
Grinding Wheels, etc.
No-load Rotational Speed
Revolutions, Surface Speed,
Strokes, etc. per Minute
Speed, Torque or Position Settings
FUNCTIONAL DESCRIPTION
7
6
BATTERY
9
8
5
Before using batter y pack, please read carefully all instructions and cautionar y markings on batter y pack, batter y
charger and product using batter y.
10
®
3
4
2
1
CONTROLS AND COMPONENTS:
1. Battery Pack
2. Release Buttons on Each Side
3. Charger
4. Indicator Lights
5. Saw Shoe
6. Trigger Switch
COMPONENT
BATTERY PACK
CHARGER
SAW BLADES
7. Lock-Off Button
8. Rubber Grip
9. Blade Clamp Knob
ACCESSORIES:
10. Saw Blades (2)
MODEL NUMBER
690549
690543
690865
9
Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode.
Do not carr y b a t t e r y p a c k s i n a p r o n s , p o c k e t s , o r t o o l
boxes, product kit boxes, drawers, etc. with loose metal objects. Battery
pack terminals could be short circuited causing damage to the battery pack,
severe burns or fire.
The batter y pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency. Before disposing of damaged or worn out Ni-Cad battery packs, check with your State Environmental
Protection Agency to find out about special restrictions on the disposal of these
battery packs, take them to your local recycling center for proper disposal, or
call 1-800-822-8837.
The batter y is not fully charged. Before first use, the battery pack requires
3-5 hours charge time to be fully charged. Subsequent recharging needs 1 hour
for the battery to be fully charged.
Always switch to a fresh batter y when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life.
Never over-discharge a batter y by using the tool even after tool performance
has decreased. Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
Charge batter y pack at ambient temperatures between 50 ° F – 104 ° F.
Store tool and batter y p a c k i n l o c a t i o n s w h e r e t e m p e r a t u r e s w i l l n o t e x c e e d
120°F. This is important to prevent serious damage to the battery cells.
The batter y pack should always be recharged when the Cordless Drill begins to
run slowly.
When batter y pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause sparks, burns, or fire.
REMOVING / ATTACHING BATTERY PACK
CHARGING BATTERY PACK
REMOVE BATTERY PACK:
1. Press both release
buttons on either
side of the Cordless
Reciprocating Saw to
release the battery
pack.
CHARGE BATTERY PACK:
1. Plug the charger into
the nearest 120 volt
electrical outlet.
2. Pull battery pack free of
Cordless Reciprocating Saw.
RELEASE
BUTTON
ATTACH BATTERY PACK:
1. Align the raised portion of the battery
pack with the groove in the battery compartment of the Cordless Reciprocating Saw.
2. Press the battery pack into place. Make sure the latches are securely fastened. Do
not use the Cordless Reciprocating Saw if the battery pack is not seated properly.
CHARGER
Before using batter y charger, p l e a s e r e a d c a r e fu ll y a l l
instructions and cautionar y markings on batter y charger, batter y pack and
product using batter y.
Use only the charger which accompanied your product or direct replacement as
listed in this manual. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
Do not disassemble charger.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
The batter y pack and charger heat during charging. Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
2. Make sure the trigger
on the Cordless
Reciprocating Saw
is in the “ O F F ”
position and remove
the battery pack
from the Cordless
Reciprocating Saw.
BATTERY PACK
LED
LIGHT
BATTERY
CHARGER
3. Insert the battery pack
into the charger. Be sure that the battery pack is fully seated in the charger. Do
not force.
4. The red indicator light should come “ O N ” indicating that the battery pack is in
a “Fast Charge” mode. If the green indicator light comes “ O N ”, then the battery
is already fully charged.
5. After approximately one hour of charging, the red indicator light should go
“ O F F ” and the green light should come “ O N ” indicating that the battery is fully
charged and the charger is now in a “Trickle Charge” mode.
6. The battery can be left in a “Trickle Charge” mode until ready to use.
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your Cordless Reciprocating Saw continuously, the batteries in your
battery pack will become hot. You should let a hot battery pack cool down for
approximately 30 minutes before attempting to recharge. When the battery pack
becomes discharged and is hot, the red light on the charger will flash. When the
battery pack cools down, the red light will glow continuously to indicate fast
charging mode, 1-hour charge time.
When the batter y pack requires recharging, a 1 hour charge allows the tool to
operate at full power. A charging indicator light on the charger will illuminate to
show that charging is taking place.
This will occur when continuous use of your Cordless
Reciprocating Saw causes the batter y pack to become hot. It does not occur
under normal circumstances.
11
12
ASSEMBLY
OPERATING THE RECIPROCATING SAW
F a i l u r e t o r e m o v e t h e b a t t e r y pack from the saw before
removing the blade could result in accidental starting and serious personal
injur y.
Be aware that this tool is always in an operating condition
because it does not have to be plugged into an electrical outlet. Always turn
the switch “ O F F ” and remove the battery pack before changing blades.
ATTACHING / REMOVING BLADE
VARIABLE SPEED TRIGGER SWITCH
BLADE CLAMP
Never tape the trigger switch down to provide continuous
high speed. The tool may fail under such conditions causing fire or personal
injury.
The lock-off button helps prevent accidental starting.
This button can be pressed from either side.
LOCK-ON
BUTTON
TRIGGER
• Remove the battery pack.
TO ATTACH BLADE:
• Rotate the clamp knob clockwise and hold to retract the clamping jaws inside
the clamp.
• Insert the shank of the blade into the clamp until the hole in the shank engages
the dent ball in the clamp.
• Release the clamp knob to tighten and secure the blade in place.
• Replace the battery pack.
TO REMOVE BLADE:
• Rotate the clamp knob clockwise and hold to retract the clamping jaws inside
the clamp.
• Pull the blade off the clamp.
• Replace the battery pack.
THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH:
• The speed of the Cordless Reciprocating Saw depends on the amount of
pressure applied on the trigger. The further the trigger is pressed, the faster
the tool will go.
• Press the lock-off button, then pull the “ O N / O F F ” trigger to turn the Cordless
Reciprocating Saw “ O N ”. To turn the Cordless Reciprocating Saw “ O F F ”,
release the trigger switch.
13
14
GENERAL CUTTING
PLUNGE CUTTING
Always hold the saw in front of you and away from your body. Keep your
hands and feet well away from the work piece.
Never feed the blade into the work piece until the blade
is at full speed. If the blade is not at full speed, the saw may kick back
causing serious personal injur y.
Never feed the blade into the work piece until the blade is at full speed.
If the blade is not at full speed, the saw may kick back causing serious
personal injur y.
Use proper blade for the particular cutting application.
• Mark out the line to be cut so it is easily visible.
• Start inside the area to be cut out.
• Depress the lock-on button and press the trigger
to start the saw.
• Put on eye protection.
• Set the shoe against the work piece.
• Clear the saw of any
foreign material.
• When the blade reaches full speed, slowly feed the blade into the work piece.
• Make sure the work piece is held
securely in place. Hold smaller
pieces in a vise or attach to the
workbench with clamps.
METAL CUTTING
• Mark out the line to be cut so it is easily visible.
• Pull the trigger to start the saw.
• Set the shoe against the work piece.
• When the blade reaches full speed, slowly feed the blade into the work piece.
Never use gasoline or any flammable liquid as a
lubricant. Sparking from the motor may cause it to ignite into flames.
• When cutting metals other then copper, brass or aluminum, always use a lubricant, such as cutting oil, to keep the blade cool. This will prolong the life of the
blade as well as speeding up the cutting process.
• Make sure the work piece is held securely in place. Hold smaller pieces, such as
pipe or conduit, in a vise or attach to the workbench with clamps.
• To eliminate vibration, always cut close to the clamping point.
• When cutting thin sheets of metal, place a piece of plywood on either side to control
vibration and prevent tearing.
15
16
OIL
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carr y
the amount of current necessar y for your power tool. If not, your tool may experience a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table on next page).
MAINTENANCE AND CLEANING
Always remove the batter y pack before attempting
cleaning or maintenance.
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W. G
AMPERE
10FT.
25FT.
50FT.
100FT.
3-6
18
18
18
18
6-8
18
18
18
16
8-10
18
18
18
14
10-12
16
16
14
14
12-16
14
12
12
16-20
12
12
12
SPECIFICATIONS
This Cordless Reciprocating Saw is lubricated before
it leaves the factor y. This lubrication should last for the life of the tool. No
further lubrication is required.
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
A l w a y s c l e a n t h e b a t t e r y pack using only a dr y c l o t h . D o n o t u s e l i q u i d s .
Always unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dr y cloth.
Inspect all mounting screws regularly. Tighten any loose screws. Failure to keep
the mounting screws tight could result in serious injuries.
SPECIFICATIONS
Voltage
19.2V
Length of Stroke
22mm (7/8")
Switch
Variable Speed with Brake
Charger Input
120V
60Hz
Charging Time
Approx. 1 hour
No Load Speed (RPM) 0-3200/min
Battery Type
Ni-Cad
PROTECTING THE ENVIRONMENT
BATTERIES
Alltrade batteries can be recharged many times. At the end of their useful life,
recycle batteries with due care for our environment.
Never open the Cordless Reciprocating Saw case, batter y pack or charger. Do not
attempt to repair the Cordless Reciprocating Saw, battery pack or charger yourself.
Opening any of these parts will void your warranty.
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.
17
18
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
3 YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ power tool and no one else all parts
of the product (except those parts referred to below which are specifically excluded from such warranty (see Exclusions)) to be free from defects in materials and
workmanship for a period of three years from original date of purchase, except that
such warranty with regard to the battery shall be for a period of two years from
original date of purchase, unless the tool is used for commercial or rental
purposes.
SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE: The above
warranty for this Kawasaki™ power tool, including the battery, shall be effective for
only 90 days from the original date of purchase if this tool is used for any
COMMERCIAL OR RENTAL PURPOSE.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any
other product and/or component thereof manufactured or distributed by Alltrade,
19
and does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsible for the return shipping charges. Alltrade’s repair and/or replacement of any nonconforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
20
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Limitations on Wa r r a n t y D i s c l a i m e r s
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
21
22