Extron electronics MTP DA4 User`s manual

User’s Manual
MTP DA4 and MTP DA8
Video, Audio, and/or Serial Link
Mini Twisted Pair Distribution Amplifiers
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2009 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
68-975-01 Rev. C
02 09
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de  tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Extron China
686 Ronghua Road, Songjiang
District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
安全须知 • 中文
警告
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过。
这个符号警告用户该设备机壳内有暴
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后
或桌面电源的电源线,或任何接到市电系统的电源线。
露的危险电压,有触电危险。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没
有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与
厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备,以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
Quick Start Guide
MTP DA4 and MTP DA8
Install and set up the MTP DA as follows:
Step 1
Turn all of the equipment off and disconnect it from the power
source.
Step 2
If the DA is part of a system that includes an MTP T 15HD A or
MTP 15HD RS transmitter, check, and if necessary, reconfigure the
serial data/audio termination and mute jumpers inside the DA. See
“Termination and Mute Jumpering — MTP 15HD Systems Only”, on
page 4.
Step 3
Connect a twisted pair (TP) cable from an
MTP transmitter, MTP SW switcher, or VTT
transmitter to the A/V Input RJ-45 connector.
See the TP connector table at right to terminate
the cable.
Step 4
Connect up to 4 or 8 TP cables between the DA’s
A/V Outputs connectors and an MTP or VTT
receiver that is compatible with the transmitted
signal. See the TP connector table at right to
terminate the cable.
TIA/EIA 568 A
TP connector
Pin Wire color
1
2
3
4
5
6
7
8
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Step 5
If desired, connect a contact closure control to the Output Mute
captive screw connector shown below. Each numbered pin is
assigned to a DA output (pin A is assigned to all DA outputs). When
you short and latch a pin or pins to ground, the DA mutes the
associated twisted pair output(s).
Pin
1
2
3
1 2 3 4 5 6 7 8 A
4
5
MTP DA4
Output Mute Connector 6
7
8
1 2 3 4 A
A
MTP DA8
Output Mute Connector
Function
CC
Out #1 Mute output #1
Out #2 Mute output #2
Out #3 Mute output #3
Out #4 Mute output #4
Out #5 Mute output #5
Out #6 Mute output #6
Out #7 Mute output #7
Out #8 Mute output #8
Out All Mute all
Gnd
Ground
MTP DA4 and MTP DA8 • Quick Start Guide
QS-1
Table of Contents
Quick Start Guide ­—
MTP DA4 and MTP DA8, cont’d
Step 6
Connect 12 VDC power. See the drawing at right.
Introduction. ................................................................................... 1
POWER
+
-
12V
0.93A MAX
0.2” (5 mm)
TP cable advantages.................................................................. 2
Transmission distance................................................................ 2
MTP 15HD A and MTP 15HD RS transmission distances..........3
MTP SV and MTP CV transmission distances............................3
VTT001/VTR001 transmission distances....................................4
Termination and Mute Jumpering —MTP 15HD Systems
Only. .................................................................................................. 4
Mounting......................................................................................... 6
Tabletop use............................................................................... 6
Rack shelf mounting.................................................................. 6
UL guidelines..............................................................................6
Rack shelf mounting instructions..............................................7
Furniture mounting................................................................... 9
Connections................................................................................... 10
Power supply wiring................................................................ 12
TP cable termination................................................................ 13
Front Panel Power Indicator.................................................... 15
Skew Delay Problems. ............................................................... 15
Specifications................................................................................ 16
Part Numbers................................................................................ 18
MTP DA distribution amplifiers.............................................. 18
Included parts.......................................................................... 18
Accessories............................................................................... 19
Cables....................................................................................... 19
Connectors............................................................................... 19
QS-2
MTP DA4 and MTP DA8 • Quick Start Guide
MTP DA4 and MTP DA8 • Table of Contents
i
MTP DA4 and MTP DA8
Table of Contents, cont’d
Introduction
The Extron MTP DA4 and MTP DA8 twisted pair (TP)
distribution amplifiers (DAs) distribute a single TP input signal
to four or eight MTP receivers. The TP input can be from any of
the following MTP transmitter and switcher families:
•
MTP T SV S-video transmitter (all models)
•
MTP T CV composite video transmitter (all models)
•
MTP T 15HD A RGB/high resolution video and audio
transmitter (all models)
•
MTP T 15HD RS RGB/high resolution video and serial
link transmitter (all models)
•
SW MTP T 15HD A video and audio switcher with builtin TP transmitter
•
VTT001 RGB/high resolution video transmitter
The MTP DAs are part of a system (figure 1) for long-distance
distribution of VGA or other high resolution video and either
audio or a serial link over TP cable. Extron’s Enhanced
Skew-Free™ A/V UTP cable is preferred, but Category (CAT) 5
shielded twisted pair (STP), unshielded twisted pair (UTP), and
foil shielded twisted pair (FTP) cable are also acceptable.
UT
MUT
E
TP
OU
8
7
1
2
3
4
5
6
7
8
A
Extron
MTP DA8
Extron
MTP R 15HD A
Twisted Pair DA
6
V OU
4
S
UT
TP 5
A/
Twisted Pair
Receiver
3
2
1
T
PU
V IN
A/
Up To
8 Receivers
R
WE
PO
-
+
12V3A
0.9
X
MA
R
15
HD
A
NO
DIO
AU 2
H SYNC +
V SYNC +
C SYNC
SOG
VIDEO
SPARE
M TP
MO
1
ON
1
PU
IN
WER
PO
T
2
3
4
5
6
UT
TP
OU
V X
12 MA
.5A
T
15
HD
A
M TP
PRE
-PE
AK
ON
AU
UT
TP
OU
DIO
OFF
TO
R
NI
MO
WER
PO
V X
12 MA
.5A
T
PU
IN
Extron
TM
Skew-Free A/V
UTP Cable
Extron
MTP T 15HD A
Twisted Pair
Transmitter
68-975-01 Rev. C
02 09
All trademarks mentioned in this manual are the properties of their respective owners.
ii
MTP DA4 and MTP DA8 • Table of Contents
PC
Sound System Plasma/LCD Projector
Figure 1 — Typical TP distribution system
MTP DA4 and MTP DA8 • Introduction
1
Introduction
The MTP DA inputs a proprietary signal on an RJ-45 connector,
buffers it, and distributes four or eight identical proprietary
signals on RJ-45 connectors.
N
The MTP DA does not support the remote power feature
of the MTP SV, MTP CV, and VTT001. You will have
to power the transmitter and all connected receivers.
A contact closure connector on the rear panel provides the
ability to mute individual outputs or all outputs.
The MTPs ship with external desktop 12 V power supplies that
accept 100 to 240 VAC, 50 Hz or 60 Hz input.
TP cable advantages
Twisted pair cable is smaller, lighter, more flexible, and less
expensive than coaxial cable. Termination of the cable with
RJ-45 connectors is simple, quick, and economical.
Transmission distance
The maximum distance for the entire transmission system is
determined by the output frequency and resolution and the
position of the transmitter’s Pre-Peak switch (if equipped). The
total recommended distances are not affected by the presence
or absence of an MTP DA in the transmission system. The
following sections specify the recommended transmission
distances using Extron Enhanced Skew-Free A/V UTP cable or
UTP CAT 5 cable, terminated with CAT 5 rated connectors
N
It is possible to exceed the recommended distance;
however, image quality may be reduced.
N
The recommendations apply to a complete transmission
system, which can include a single transmitter, one or
more DAs, and one or more daisy-chained receivers. For
example, the maximum suggested range for 1024 x 768
video is 300’ with Pre-Peak off in an MTP 15HD system.
N
If you are using the DA as part of an MTP 15HD RS
(serial data) transmission system, be aware that the DA
routes the serial link one way only, from the transmitter
to the receiver(s).
Also, the transmitter and receiver must be jumper
configured to pass the serial link one way only. Refer to
the MTP 15HD RS User's Manual.
The table below specifies the recommended transmission
distances and transmitter Pre-Peak switch positions for
MTP 15HD RGB transmission systems.
2
MTP DA4 and MTP DA8 • Introduction
Recommended transmission ranges at 60 Hz,
MTP 15HD A and MTP 15HD RS systems
Video
format
Composite,
S-video,
Component
Pre-Peak
off
Pre-Peak Max. distance Max. distance
on
(high quality) (variable quality)
800'
(245 m)
1000'
(300 m)
<300'
(90 m)
<300'
(90 m)
<300'
(90 m)
<300'
(90 m)
<250'
(75 m)
<250'
(75 m)
<250'
(75 m)
<250'
(75 m)
<250'
(75 m)
<250'
(75 m)
<250'
(75 m)
<250'
(75 m)
>350'
(105 m)
>350'
(105 m)
>350'
(105 m)
>350'
(105 m)
>300'
(90 m)
>300'
(90 m)
>300'
(90 m)
>300'
(90 m)
>300'
(90 m)
>300'
(90 m)
>300'
(90 m)
>300'
(90 m)
700'
(215 m)
550'
(165 m)
500'
(150 m)
400'
(120 m)
350'
(105 m)
400'
(120 m)
400'
(120 m)
400'
(120 m)
350'
(105 m)
350'
(105 m)
300'
(90 m)
300'
(90 m)
750'
(240 m)
650'
(200 m)
600'
(185 m)
500'
(150 m)
450'
(135 m)
500'
(150 m)
450'
(135 m)
450'
(135 m)
400'
(120 m)
400'
(120 m)
450'
(135 m)
400'
(120 m)
HDTV 1080i
<250'
(75 m)
<250'
(75 m)
>300'
(90 m)
>300'
(90 m)
400'
(120 m)
300'
(90 m)
500'
(150 m)
400'
(120 m)
HDTV 1080p
<250'
(75 m)
>300'
(90 m)
300'
(90 m)
400'
(120 m)
640 x 480
800 x 600
1024 x 768*
1280 x 960*
1280 x 1024*
1360 x 765
1365 x 768
1366 x 768
1400 x 1050
1440 x 900
1600 x 1200*
1920 x 1200
HDTV 720p
MTP SV and MTP CV transmission distances
Extron suggests a minimum transmission distance of at least 50'
(15 m). The maximum transmission distance is 1000' (300 m).
VTT001/VTR001 transmission distances
The following table specifies the maximum recommended
transmission distances for a VTT001/VTR001 system at 60 Hz.
MTP DA4 and MTP DA8 • Introduction
3
Installation
Termination and Mute Jumpering —
MTP 15HD Systems Only
N
The position of jumpers J3 and J9 have no effect when the
DA is installed as a part of an MTP CV series, MTP SV
series, or VTT001/VTR001 system.
S
J9
Jumper Block J9
Inside Box
J3
Jumper Blocks J3
Inside Box
TE
UT
MU
TP
OU
8
7
1
2
3
4
5
6
7
8
A
6
S
UT
5
TP
A/V
4
OU
3
2
1
A jumper block inside the MTP DA that set the DA to
properly terminate the audio or serial portion of the input
signal when the input signal was transmitted by an MTP 15HD A
series (audio), SW MTP T (audio), or MTP 15HD RS series
(serial) transmitter.
UT
A/V
INP
WER
PO
-
+
X
A
V
12 A M
0.93
A second jumper block sets the DA to mute the audio or serial
link when its video mute function is activated, or to always pass
the audio or serial link regardless of the contact closure mute
status.
Remove 6 screws,
lift top straight up.
Figure 2 — Opening the DA and termination
jumpering
1.
If applicable, disconnect all cables, remove the DA from its
installation location, and remove any mounting brackets
installed.
2.
Remove the two screws from either side of the DA and
the two screws on the top (six screws total) and lift the top
cover off of the DA (figure 2).
N
Select audio or serial distribution — Locate jumper J3 on
the main board and shift the jumper from the audio (A)
(rear) to the serial (S) (front) position (figure 2).
When J9 is set to the disable mute (S) (front) position,
the video mute has no effect on the DA’s audio or serial
distribution.
When J9 is set to the enable mute (A) (rear) position, the
DA mutes the audio or serial output when its contact
closure video mute is activated.
3.
4
Enable
Mute
or
Audio
When an MTP T 15HD A or SW MTP T A provides the input,
the MTP DA’s output can include analog audio in addition to
the RGB video. When an MTP T 15HD RS provides the input,
the DA output can include a serial (R-232) link in addition to the
RGB video.
By default, the MTP DA is configured with the internal jumpers
set to terminate audio. For serial data applications, the DA can
be configured to properly terminate that signal as follows:
A
S
or
A
A
Serial
Disable
Mute
S
(120 m)
(90 m)
(60 m)
(45 m)
A
400'
300'
200'
150'
S
800 x 600
1024 x 768
1280 x 1024
1600 x 1200
A
500' (150 m)
S
640 x 480
S
Recommended
Maximum range
A
Video
format
MTP DA4 and MTP DA8 • Installation
4.
Enable or disable audio or serial distribution mute — If
desired, locate jumper J9 on the main board and shift the
jumper from the disable mute (S) (front) to the enable mute
(A) (rear) position (figure 2).
MTP DA4 and MTP DA8 • Installation
5
Installation, cont’d
5.
Replace the top cover.
6.
Reinstall the six screws removed in step 2. If any
mounting brackets were removed in step 1, put them back
into position as you reinstall the screws.
7.
If applicable, reinstall the DA and reconnect all cables.
Mounting
C
4.
Circuit overloading — Consideration should be given to
the connection of the equipment to the supply circuit and
the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be
used when addressing this concern.
5.
Reliable earthing (grounding) — Reliable earthing
of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections
other than direct connections to the branch circuit (such as
the use of power strips).
Installation and service must be performed by
authorized personnel only.
The 1U high, half rack width MTP DA can be set on a table,
mounted on a rack shelf, mounted to a rack without a shelf, or
mounted under a desk or tabletop.
Tabletop use
Four self-adhesive rubber feet are included with the DA. For
tabletop use, attach one foot at each corner of the bottom side of
the unit and place the unit in the desired location.
Rack shelf mounting
Rack shelf mounting instructions
1. Remove feet from the bottom of the DA if installed.
2.
Mount the DA on the rack shelf, using two 4-40 x 3/16"
screws in opposite (diagonal) corners to secure it to the
shelf (figure 3 and figure 4).
3.
Install blank panel(s) or other unit(s) on the rack shelf.
4.
Attach the rack shelf to the rack using the supplied bolts.
For optional rack mounting, mount the DA using any of the
following rack mounting options:
•
RSU 129 9.5" deep 1U universal rack shelf kit (part #60-190-01)
•
RSB 129 9.5" deep 1U basic rack shelf (part #60-604-01)
•
RSU 126 6" deep universal rack shelf kit (part #60-190-10)
•
RSB 126 6" deep basic rack shelf (part #60-604-10)
UL guidelines
The following Underwriters Laboratories (UL) requirements
pertain to the installation of the DA into or onto a rack.
1.
6
Elevated operating ambient — If installed in a closed
or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater
than room ambient. Therefore, consider installing the
equipment in an environment compatible with the +122 °F
(+50 °C) maximum ambient temperature (Tma) specified
by Extron.
2.
Reduced air flow — Installation of the equipment in a rack
should be such that the amount of air flow required for
safe operation of the equipment is not compromised.
3.
Mechanical loading — Mounting of the equipment in
the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
MTP DA4 and MTP DA8 • Installation
6" Deep Rack Shelf
1/2 Rack Width False Front
Face Plate
(2) 4-40 x 3/16" screws
MT
P DA
SE
RIES
Use 2 mounting holes on
opposite corners.
Figure 3 — Mounting on a 6" deep rack shelf
MTP DA4 and MTP DA8 • Installation
7
Installation, cont’d
Furniture mounting
Do not attach the rubber feet. Furniture mount the DA using the
optional mounting kit (part #70-077-01) as follows:
1U Universal
Rack Shelf
1.
Remove rubber feet if they were previously installed on
the bottom of the DA.
2.
Attach the furniture mounting brackets to the DA with the
provided machine screws (figure 5).
False Front Panel
(uses 2 screws)
(2) 4-40 x 3/16" screws
MTP
DA
SE
RI
ES
Use 2 mounting holes on
opposite corners
Figure 4 — Mounting on a 1U universal rack shelf
MT
PD
A
SE
RIE
S
Figure 5 — Attaching the furniture mounting
brackets to an MTP DA
8
MTP DA4 and MTP DA8 • Installation
3.
Hold the DA with the attached brackets against the
underside of the table or other furniture. Mark the location
of the screw holes of the bracket on the mounting surface.
4.
Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm)
deep in the mounting surface at the marked screw
locations.
5.
Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until just less than
1/4" of the screw protrudes.
6.
Align the mounting screws with the slots in the brackets
and place the DA against the surface, with the screws
through the bracket slots.
7.
Slide the DA slightly forward or back, then tighten all four
screws to secure the unit in place.
MTP DA4 and MTP DA8 • Installation
9
Installation, cont’d
Connections
N
C
Do not connect these devices to a computer data or
telecommunications network.
MTP DA8
POWER
A/V INPUT
1
2
3
A/V OUTPUTS
4
5
6
7
8
- +
12V
0.93A MAX
1
d
OUTPUT MUTE
1 2 3 4
2
3
5 6 7 8 A
4
MTP DA4
POWER
A/V INPUT
1
A/V OUTPUTS
2
3
- +
12V
0.93A MAX
Output Mute connections — The Output Mute connector
provides a way to mute (blank) any or all TP outputs. Each
numbered pin of the captive screw connector is assigned to
one of the DA’s outputs (pin A is assigned to all DA outputs)
(figure 7). When you short and latch a numbered pin or pins to
ground, the DA mutes the associated output(s).
MTP DA8
Output Mute Connector
4
OUTPUT MUTE
1 2 3 4 A
1 2 3 4
1
See the recommended transmission ranges in the table on
page 3. The table’s recommendations apply to a complete
transmission system, which can include a single
transmitter, DA, and multiple receivers or a complex
system including multiple daisy-chained receivers.
2
3
4
5 6 7 8 A
MTP DA4
Output Mute Connector
Figure 6 — DA rear panel features
a
b
c
1 2 3 4 A
Power connector — Plug the included external 12 VDC power
supply into this 2-pole captive screw connector. See "Power
supply wiring", on page 12, to wire the connector.
Contact closure
Out #1
Out #2
Out #3
Out #4
Out #5
Out #6
Out #7
Out #8
Out All
Gnd
Function
Mute output #1
Mute output #2
Mute output #3
Mute output #4
Mute output #5
Mute output #6
Mute output #7
Mute output #8
Mute all outputs
Ground
Figure 7 — Mute connector and pinout
A/V Input connector — Connect one end of the cable carrying
the video and audio or serial TP link from the transmitting
device, to this RJ-45 female connector.
See "TP cable termination", on page 13, to wire the RJ-45
connectors.
A/V Output connector — Connect one end of up to four or eight
TP cables to these RJ-45 female connectors.
Connect the free ends of the same cables, carrying the
distributed video and audio or serial TP link, to the RJ-45
connectors on the receivers.
See "TP cable termination", on page 13, to wire the RJ-45
connectors.
N
10
Pin
1
2
3
4
5
6
7
8
A
The MTP DA’s output does not provide any pre-peaking
control. The total recommended distance for a complex
system with multiple DA outputs is the same as for a
simple system with a single transmitter and receiver.
MTP DA4 and MTP DA8 • Installation
MTP DA4 and MTP DA8 • Installation
11
Installation, cont’d
Power supply wiring
Figure 8 shows how to wire the power connector.
Alternatively, an optional Extron PS 123 Universal 12 VDC
Power Supply, part #60-814-01, can power multiple Extron
12 VDC devices using only one AC power connector.
TP cable termination
2-Pole Captive Screw
Connector
Tie Wrap
3/16”
(5 mm) Max.
SECTION A–A
Smooth
Ridges
A
N
RJ-45 termination with CAT 5, CAT 5e, or
CAT 6 cable must comply with the TIA/EIA T 568A or
TIA/EIA T 568B wiring standards for all connections.
RJ-45 termination with Skew-Free A/V UTP cable must
comply with TIA/EIA T 568 A only.
Figure 9 on the next page details the termination of TP cables
with RJ-45 connectors in accordance with the TIA/EIA T 568A
or TIA/EIA T 568B wiring standards. Use either standard with
CAT 5/5e/6 cable, but use the same standard on both ends of
the cable.
Note the separate columns for input from a low resolution
(composite video or S-video) and high resolution (RGB
video) MTP. Note also the shaded table that identifies the
unconventional signal assignment when a low resolution MTP
unit is jumpered for stereo audio.
A
Power Supply
Output Cord
Figure 8 — Power connector wiring
N
Enhanced Skew-free A/V cable is not recommended for
Ethernet/LAN applications.
C
This cable is specially designed for compatibility
with Extron’s Twisted Pair products, wired using the
TIA/EIA 568 A standard.
The green, brown, and blue pairs of this cable have
virtually identical lengths and should be used to
transmit the RGB, composite video, or S-video signals.
Power supply voltage polarity is critical. Incorrect
voltage polarity can damage the power supply
and the unit. The ridges on the side of the cord
(figure 8) identify the power cord negative lead.
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
W
The two power cord wires must be kept separate
while the power supply is plugged in. Remove
power before wiring.
The orange pair of this cable has a different length and
should not be used to transmit the RGB, composite
video, or S-video signals.
C
The length of the exposed (stripped) copper
wires is important. The ideal length is 3/16”
(5 mm). Longer bare wires can short together.
Shorter wires are not as secure in the connectors
and could be pulled out.
N
If you are using the DA as part of an MTP 15HD RS
(serial data) transmission system, be aware that the DA
routes the serial link one way only, from the transmitter
to the receiver(s).
Also, the transmitter and receiver must be jumper
configured to pass the serial link one way only. Refer to
the MTP 15HD RS User's Manual.
N
Do not tin the power supply leads before installing them
in the direct insertion connector. Tinned wires are not as
secure in the connectors and could be pulled out.
Use the supplied tie-wrap to strap the power cord to the
extended tail of the connector.
12
MTP DA4 and MTP DA8 • Installation
MTP DA4 and MTP DA8 • Installation
13
Installation, cont’d
NOTE When the TP input is from a low resolution unit (MTP SV, MTP CV, or MTP AV), the signal
assignment depends on the position of signal jumpers in the transmitter and receiver.
Refer to the MTP Series Users’ Guide.
Front Panel Power Indicator
Figure 10 identifies the front panel power LED.
Jumpers in
Mono position (default)
568 A
Wire
Pin color
568 B
Wire
color
Composite
video
MTP signal
1 Whitegreen
Whiteorange
Reserved
Chroma (C) +
Red/
V. Sync +
2 Green
Orange Reserved
Chroma (C) –
Red/
V. Sync –
Mono audio +
Mono audio +
or RS-232 +
(MTP 15HD
only)
3
RJ-45
Connector
Side
Pins:
12345678
Insert
Twisted
Pair Wires
White- Whiteorange green
Mono
audio +
S-video
MTP
signal
RGB video
MTP, VTT/VTR
signal
4 Blue
Blue
Video +
Luma (Y) +
5
Whiteblue
Video –
Luma (Y) –
Green –
6 Orange Green
Mono
audio –
Mono audio –
Mono audio –
or RS-232 –
(MTP 15HD
only)
7
Whiteblue
Whitebrown
Whitebrown
Reserved
Reserved
Blue/
H. Sync +
8 Brown
Brown
Reserved
Reserved
Blue
H. Sync –
Jumpers in
Stereo position
568 A
Wire
Pin color
MTP DA SERIES
1
Figure 10 — MTP receiver front panels
a
Power LED — Indicates power is applied to the MTP DA.
Skew Delay Problems
CAT 5 TP cable can lead to registration errors between the red,
green, and blue video signals. Pair skew can be measured with
test equipment or identified by viewing a crosshatch test pattern
with a critical eye to determine if either the red, green, or blue
video image leads (appears to the left of) the other two video
images. These images can be minimized or eliminated by one of
the following methods:
•
Using a skew delay adjusting receiver:
(MTP RL 15HD A SEQ or MTP RL 15HD RS SEQ)
•
Switching to Extron’s Enhanced Skew-Free A/V UTP
cable
568 B
Wire
color
Composite
video
MTP signal
1 Whitegreen
Whiteorange
Video +
Luma (Y) +
•
Adding a skew compensation cable equal to the length of
pair skew to the receiver’s video output
2 Green
Orange Video –
Reserved
Luma (Y) –
Reserved
•
Blue
Audio
left +
Chroma (C) &
audio left +
Installing an SEQ 100 15HD Skew Equalizer on the
receiver’s video output and adjusting the skew for the
leading video image
Whiteblue
Audio
left –
Chroma (C) &
audio left –
3
White- Whiteorange green
4 Blue
5
Whiteblue
S-video
MTP
signal
Reserved
Reserved
Whitebrown
Whitebrown
Audio
right +
Audio right+
8 Brown
Brown
Audio
right –
Audio right –
6 Orange Green
7
NOTE If you are using Enhanced Skew-Free™ A/V cable,
use the TIA/EIA T 568A standard only.
Figure 9 — TP cable termination
14
MTP DA4 and MTP DA8 • Installation
MTP DA4 and MTP DA8 • Installation
15
Reference Information
Specifications
Video
Gain������������������������������������������������� Unity
Video input— see transmitters’ specifications
Number/signal type��������������������� 1 set of proprietary analog signals
Connectors������������������������������������� 1 female RJ-45
Video output— see receivers’ specifications
Number/signal type
MTP DA4���������������������������� 4 sets of proprietary analog signals
MTP DA8���������������������������� 8 sets of proprietary analog signals
Connectors
MTP DA4���������������������������� 4 female RJ-45
MTP DA8���������������������������� 8 female RJ-45
Maximum resolution�������������������� 1920x1200
N
Refer to the user’s manual for the maximum distances recommended for
specific resolutions.
Audio
Gain������������������������������������������������� Unity (0 dB)
Audio input— see transmitters’ specifications
Number/signal type��������������������� 1 set of proprietary analog signals
Connectors������������������������������������� 1 female RJ-45
Audio output— see receivers’ specifications
Number/signal type
MTP DA4���������������������������� 4 sets of proprietary analog signals
MTP DA8���������������������������� 8 sets of proprietary analog signals
Connectors
MTP DA4���������������������������� 4 female RJ-45
MTP DA8���������������������������� 8 female RJ-45
16
MTP DA4 and MTP DA8 • Reference Information
Control/remote— distribution amplifier
Contact closure (latching)
MTP DA4���������������������������� (1) 3.5 mm captive screw connector, 6 pole
for contact closure output mute control
MTP DA8���������������������������� (1) 3.5 mm captive screw connector, 10
pole for contact closure output mute
control
Contact closure pin configurations
MTP DA4���������������������������� 1 = mute output 1, 2 = mute output 2,
3 = mute output 3, 4 = mute output 4,
5 = mute all outputs, 6 = GND
MTP DA8���������������������������� 1 = mute output 1, 2 = mute output 2,
3 = mute output 3, 4 = mute output 4,
5 = mute output 5, 6 = mute output 6,
7 = mute output 7, 8 = mute output 8,
9 = mute all outputs, 10 = GND
General
Recommended cable type������������ Enhanced Skew-Free™ A/V UTP Cable or
CAT 5/5E/6 (shielded or unshielded)
External power supply����������������� 100 VAC to 240 VAC, 50/60 Hz, external
MTP DA4���������������������������� 12 VDC, 2 A, regulated
MTP DA8���������������������������� 12 VDC, 3 A, regulated
Power input requirements����������� 12 VDC, 0.93 A
Temperature/humidity���������������� Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling������������������������������������������� Convection, no vents
Mounting
Rack mount������������������������ Yes, with optional 1U, 9.5" deep rack shelf,
part #60-190-01 (RSU 129) or 60-604-01
(RSB 129) or 1U, 6"deep rack shelf,
part #60-190-10 (RSU 126) or 60-604-10
(RSB 126).
Furniture mount���������������� Yes, with optional Under-Desk Mounting
Kit #70-077-01 (MBU 125) Pole mount������������������������� Yes, with optional Projector Mounting Kit
#70-077-04 (PMK 200)
Enclosure type������������������������������� Metal
Enclosure dimensions������������������� 1.75" H x 8.75" W x 6" D
(1U high, half rack wide)
(4.4 cm H x 22.2 cm W x 15.2 cm D)
(Depth excludes connectors.)
MTP DA4 and MTP DA8 • Reference Information
17
Reference Information, cont’d
Product weight������������������������������ 1.2 lbs (0.5 kg)
Shipping weight���������������������������� 4 lbs (2 kg)
Vibration����������������������������������������� ISTA 1A in carton
(International Safe Transit Association)
Regulatory compliance
Safety����������������������������������� CE, CUL, UL
EMI/EMC�������������������������� CE, C-tick, FCC Class A, ICES, VCCI
MTBF����������������������������������������������� 30,000 hours
Warranty����������������������������������������� 3 years parts and labor
N
All nominal levels are at ±10%.
N
Specifications are subject to change without notice.
Accessories
Accessory
RSU 129 1U universal rack shelf
60-190-01
RSB 129 1U basic rack shelf
60-604-01
RSU 126 6" deep universal rack shelf
60-190-10
RSB 126 6" deep basic rack shelf
60-604-10
MBU 125 under-desk mounting kit
70-077-01
PMK 200 pole mount kit
70-077-04
Cables
N
Part Numbers
Part number
MTP DA4
60-685-01
MTP DA8
60-686-01
Included parts
These items are included in each order for an MTP SW6:
DA
Part number
12 VDC power supply
18
Enhanced Skew-Free™ A/V UTP cables are not
recommended for Ethernet/LAN applications.
Enhanced Skew-Free™ A/V cable
MTP DA distribution amplifiers
DA
Part number
MTP DA4
28-071-01
MTP DA8
28-113-01
Part number
Enhanced Skew-Free A/V cable
(cut, various lengths)
26-569-xx
Enhanced Skew-Free A/V 1000'
(Bulk) (non-plenum)
22-141-03
Plenum enhanced Skew-Free A/V 1000'
(Bulk)
22-142-03
Connectors
Connector
Part number
CAT 6 jack (black), qty. 10
100-476-01
CAT 6 jack (red), qty. 10
100-477-01
CAT 6 jack (blue), qty. 10
100-478-01
MTP DA Series User’s Guide
CAT 6 jack (orange), qty. 10
100-479-01
IEC power cord
CAT 6 jack (gray), qty. 10
100-480-01
Rubber feet
CAT 6 jack (white), qty. 10
100-481-01
Tweeker
CAT 6 jack (ivory), qty. 10
100-482-01
MTP DA4 and MTP DA8 • Reference Information
MTP DA4 and MTP DA8 • Reference Information
19