Motorola I570 - SOUTHERNLINC User`s guide

i570 Phone
User’s Guide
Dummy Page - To be discarded before printing
The SIM card provided in this kit is intended for use
with the phone provided in this package.
Loss of certain features will result when using a SIM
card from one of the following models: i30sx, i35s,
i50sx, i55sr, i58s, i60c, i80s, i85s, i88s, i90c, i95cl
series, and the i2000 series.
For more information on SIM card compatibility, go to
Defects or damage to your Motorola phone that result
from the use of non-Motorola branded or certified
Accessories, including but not limited to replacement
housings and or other peripheral accessories, are
excluded from warranty coverage. Please refer to the
text of Motorola's Limited One Year warranty located
in this user’s guide for complete details.
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party Name: Motorola, Inc.
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: i570
Model Number: H65XAN6RR4CN
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a),
15.107(d) and section 15.109(a)
Class B Digital Device
As a personal computer peripheral, this device
complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Introducing your new Motorola i570 phone. Here’s a quick anatomy lesson.
Speaker On/Off Key
Left Soft Key
Perform function
in lower left
Right Soft Key
Perform function
in lower right
Menu Key
From home screen,
open main menu.
Power Key
Turns phone on.
Talk Key
Make &
answer calls.
Navigation Key
End Key
End calls, exit
menu system.
OK Key
In menus & lists,
press to select
highlighted option.
Smart Key
Volume Keys
PTT Button
External Display
Audio Jack
check it out
Home Screen
Main Menu
Main Menu
aq b
cd e
fo g
2 Customizable O key
that can be used
to open the
Ring Tones screen
1 Press and hold the
Power Key W for a
few seconds, or until
the screen lights up,
to turn on your phone.
Press the Navigation Key
up, down, left or right ( )
to highlight a menu feature.
Press the O key
to select.
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
1-800-331-6456 (United States)
1-888-390-6456 (TTY/TDD United States for hearing impaired)
1-800-461-4575 (Canada)
Product Support:
Certain mobile phone features are dependent on the capabilities
and settings of your service provider’s network. Additionally,
certain features may not be activated by your service provider,
and/or the provider's network settings may limit the feature’s
functionality. Always contact your service provider about feature
availability and functionality. All features, functionality, and other
product specifications, as well as the information contained in this
user's guide are based upon the latest available information and
are believed to be accurate at the time of printing. Motorola
reserves the right to change or modify any information or
specifications without notice or obligation.
Caution: Changes or modifications made in the radio phone, not
expressly approved by Motorola, will void the user's authority to
operate the equipment.
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. All other product or service names are
the property of their respective owners. Java and all other Java-
based marks are trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other countries.
© Motorola, Inc., 2007.
Manual Number: NNTN7316A
Software Version: D8A.00.10
CP Version: 5F.03.00
USR Version: U8AA.02.02
Electrical Requirements:
Lithium Ion Battery 3.7V
Power Adapter: 100-240V ~ 50-60Hz, 0.3A
Output of the Adapter: 5V 850mA
check it out . . . . . . . . . . . 2
contents . . . . . . . . . . . . . . 4
menu map . . . . . . . . . . . . 6
Use and Care . . . . . . . . . . 8
essentials . . . . . . . . . . . . . 9
about this guide. . . . . . . 9
SIM card . . . . . . . . . . . 10
battery . . . . . . . . . . . . . 11
turn it on & off . . . . . . . 14
enable security . . . . . . 14
make a phone call . . . . 15
answer a phone call. . . 15
make an InstantLINC
Mobile to Mobilecall . . 15
answer an InstantLINC
Mobile to Mobile call . . 16
store a phone
number or LINC ID . . . 16
call a stored phone
number or LINC ID . . .
find your phone
number and LINC ID . .
text messages. . . . . . .
manage memory . . . . .
using your handset
as a modem. . . . . . . . .
main attractions . . . . . .
LINC features . . . . . . .
one touch PTT . . . . . . .
surveillance profile. . . .
basics . . . . . . . . . . . . . . .
display . . . . . . . . . . . . .
text entry . . . . . . . . . . .
navigation key . . . . . . .
handsfree speaker. . . .
airplane mode . . . . . . .
features for the
hearing impaired . . . . .
calls. . . . . . . . . . . . . . . . .
recent calls . . . . . . . . .
caller ID . . . . . . . . . . . .
call forward . . . . . . . . .
voice name . . . . . . . . .
emergency calls . . . . .
international calls. . . . .
speed dial . . . . . . . . . .
voice mail . . . . . . . . . .
LINCaround . . . . . . . . .
customize. . . . . . . . . . . .
volume. . . . . . . . . . . . .
ring tones . . . . . . . . . .
wallpaper . . . . . . . . . . .
datebook . . . . . . . . . . .
hide or show
location information . . 51
other features . . . . . . . . 53
advanced calling . . . . . 53
contacts . . . . . . . . . . . 54
datebook. . . . . . . . . . . 55
GPS . . . . . . . . . . . . . . 55
handsfree . . . . . . . . . . 56
pc applications . . . . . . 57
personalize . . . . . . . . . 57
TTY . . . . . . . . . . . . . . . 58
security. . . . . . . . . . . . 58
Safety and General
Information . . . . . . . . . . 62
Service & Repairs . . . . . 67
Specific Absorption
Rate Data . . . . . . . . . . . 68
Motorola Limited Warranty
for the United States and
Canada . . . . . . . . . . . . . 70
Hearing Aid
Compatibility . . . . . . . .
Information From the
World Health
Organization . . . . . . . . .
Patent and Trademark
Information . . . . . . . . . .
Privacy and
Data Security . . . . . . . .
Smart Practices
While Driving . . . . . . . .
menu map
main menu
b Settings (see next page)
n Downloads
a Browser Apps
q Java Apps
• Buy More
• Java System
Ring Tones
• Buy Ring Tones
• Vibrate All: On/Off
• Ringers
• Vibrate
• Silent
My Pictures
Call Forward
• Forward: All Calls
• To: On/Off
• Go To LINCaround
• LA Options
• Help
• [New VoiceRec]
• [New Event]
menu map
• [New Entry]
• 1)Shortcuts
• 2)Cntcs[New Contact]
• 3)Ring Tones
• 4)LINC Manager
• 5)Browser Apps
• 6)Java Apps
• 7)Settings
• 8)Profiles
• 9)Call Forward
• [New Profile]
• Surveillance
• Standard
• Car
• Meeting
• Office
• Outdoors
• Headset
Call Alert
Call Timers
• Last Call
• Phone Reset
• Phone Lifetime
• Prvt/Grp Reset
• Prvt/Grp Life
• Circuit Reset
• Circuit Lifetime
• Kbytes Reset
My Info
• My Name
• Line 1
• Line 2
• Group ID
• Carrier IP
• IP1 Address
• IP2 Address
• Circuit Data
Recent Calls
• [New Contact]
• [Create Message]
• Voice Mail
• Fax Mail
• Net Alert
• Text Inbox
• Drafts
• Text Outbox
• Quick Notes
• Position
• Privacy
• Interface
settings menu
• Wallpaper
• Palette
• Text Size
• Home Icons
• Backlight
• Clock
• Menu View
• Large Dialing: On/Off
• Contrast Ext
• Language
Phone Calls
• Set Line
• Any Key Ans
• Auto Redial
• Call Waiting
• Auto Ans
• Flip Activation
• Minute Beep
• Call Duration
• Hearing Aid
• Notifications
• Tkgrp Silent
• Tkgrp Area
• One Touch PTT
• Alert Type
• LINC View: On/Off
• Menu Options
• Up Key
• Down Key
• Left Key
• Right Key
• Center Key
• Left Sftkey
• Right Sftkey
• Power Up
• Line 1
• Line 2
• Messages
• Earpiece
• Speaker
• Keypad
• Java Earpiece
• Java Speaker
• Data
• Phone Lock
• Keypad Lock
• Change Passwords
• Alert Timeout:
• Headset/Spkr:
• Connectivity
• Reset Defaults
• Return to Home
• Airplane Mode
• Phone Only
• Baud Rate
menu map
Use and Care
Use and Care
To care for your Motorola phone, please keep it away from:
liquids of any kind
Don’t expose your phone to
water, rain, extreme humidity,
sweat, or other moisture.
dust and dirt
Don’t expose your phone to
dust, dirt, sand, food, or other
inappropriate materials.
extreme heat or cold
Avoid temperatures below
-10°C/14°F or
above 45°C/113°F.
cleaning solutions
To clean your phone, use only a
dry soft cloth. Don’t use alcohol
or other cleaning solutions.
Don’t try to dry your phone in a
microwave oven.
the ground
Don’t drop your phone.
Use and Care
Caution: Before using the phone for the first
time, read the Important Safety and Legal
information included in the gray edged pages
at the back of this guide.
about this guide
This guide shows how to locate a menu
feature as follows:
Find it: M > Settings
This means that, from the home screen:
1 Press the menu key M to open the
2 Press the navigation key
to scroll to
Settings, and press the center key O to
select it.
This means a feature is network/
subscription dependent and may
not be available in all areas. Contact
SouthernLINC Wireless for more
This means a feature requires an
optional accessory.
SIM card
2 Carefully slide your SIM card into the
SIM card holder.
insert the SIM card
Turn off your phone and remove your battery
before you install or remove a SIM card.
1 Slide the latch and open the SIM card
3 Close the SIM card holder.
Warning: To avoid loss or damage, do not
remove your SIM chip from your phone
unless absolutely necessary.
Battery or Unable to Charge, take the
following steps:
Battery Use & Battery Safety
• Remove the battery and inspect it to
confirm that it bears a Motorola
“Original Equipment” hologram;
• Motorola recommends you always
use Motorola-branded batteries and
chargers. The warranty does not cover
damage caused by non-Motorola
batteries and/or chargers.
Caution: Use of an unqualified battery
or charger may present a risk of fire,
explosion, leakage, or other hazard.
Improper battery use, or use of a
damaged battery, may result in a fire,
explosion, or other hazard.
• Battery usage by children should be
• Important: Motorola mobile devices
are designed to work best with
qualified batteries. If you see a
message on your display such as Invalid
• If there is no hologram, the battery
is not a qualified battery;
• If there is a hologram, replace the
battery and retry charging it;
• If the message remains, contact a
Motorola Authorized Service Center.
• New batteries or batteries stored for a
long time may take more time to
• Charging precautions: When
charging your battery, keep it near
room temperature. Never expose
batteries to temperatures below 0°C
(32°F) or above 45°C (113°F) when
charging. Always take your mobile
device with you when you leave your
• When storing your battery, keep it in a
cool, dry place.
• It is normal over time for battery life to
decrease, and for the battery to exhibit
shorter runtime between charges or
require more frequent or longer
charging times.
• Avoid damage to battery and mobile
device. Do not disassemble, open,
crush, bend, deform, puncture, shred,
or submerge the battery or mobile
device. Avoid dropping the battery or
mobile device, especially on a hard
surface. If your battery or mobile
device has been subjected to such
damage, take it to a Motorola
Authorized Service Center before
using. Do not attempt to dry it with an
appliance or heat source, such as a hair
dryer or microwave oven.
• Use care when handling a charged
battery: particularly when placing it
inside a pocket, purse, or other
container with metal objects. Contact
with metal objects (e.g., jewelry, keys,
beaded chains) could complete an
electrical circuit (short circuit), causing
the battery to become very hot, which
could cause damage or injury.
Promptly dispose of used batteries in
accordance with local regulations.
Contact your local recycling center for
proper battery disposal.
Warning: Never dispose of batteries in a fire
because they may explode.
battery installation
1 Slide the release button back until it
releases the battery door.
2 Remove the battery door.
3 Push the battery down until it snaps in
4 Replace the battery door and press it
gently until you hear a click.
battery charging
New batteries are not fully charged.
1 Insert the charger
into the connector
on your phone as
2 Plug the other end
of the charger into
the appropriate
electrical outlet.
When you charge the
battery, the battery level
indicator at the upper
right of the screen shows charging progress.
At least one segment of the indicator must be
visible to ensure full phone functionality while
Tip: Motorola batteries have circuitry that
protects the battery from damage from
overcharging. Of course, unplugging the
charger from the wall will avoid current drain.
turn it on & off
To turn on your phone,
press and hold W for a
few seconds or until the
display turns on. If
prompted, enter your
four-digit unlock code.
To turn off your phone,
press and hold W for
two seconds.
enable security
You must enable security the first time you
power on you phone or within 10 days of first
1 Press and hold E to power on your
2 Press - under Ok.
3 Your are prompted to enable security.
Press - under Yes.
4 Press o to return to the idle screen.
make a phone call
Enter a phone number and press O to make
a call or use a voice name. See “voice name”
on page 39.
Tip: For best performance avoid touching the
antenna with your fingers during the call.
To hang up, close the flip or press o.
answer a phone call
1 If you want to talk on speaker phone,
press the speaker key t without
opening the flip. To hang up press the
smart key ..
2 If you want to answer the call using the
ear speaker, just open the flip and press
O. To hang up, close the flip or press
Note: You must have the Flip Activation feature
On. See “flip activation” on page 54.
make an InstantLINC
Mobile to Mobilecall
With InstantLINC Mobile to Mobile calls, you
use your phone as a long-range, digital 2-way
radio using one-to-one InstantLINC Mobile to
Mobile calls or one-to-many Talkgroup calls.
When your phone rings and/or vibrates, you
have the following options to answer the call:
Your LINC ID is the number at which you
receive one-to-one InstantLINC Mobile to
Mobile calls.
answer an InstantLINC
Mobile to Mobile call
Talkgroup numbers are numbers through
which you receive one-to-many group calls.
1 To make an InstantLINC Mobile to Mobile
call, enter the LINC ID you want to call.
1 When your phone emits a chirping sound
or vibrates to indicate you are receiving an
InstantLINC Mobile to Mobile call, wait for
the caller to finish speaking.
2 Press and hold the PTT button. Begin
talking after your phone emits a chirping
2 Press and hold the PTT button and begin
talking after your phone emits a chirping
3 Release the PTT button to listen.
3 Release the PTT button to listen.
To end the call press o, or press under Exit.
An InstantLINC Mobile to Mobile call ends
automatically if there is no activity on the
call for a few seconds.
Tip: To let someone know you want to talk to
them on an InstantLINC Mobile to Mobile call,
press - under Alert and press the PTT button.
To end the call press - under Exit.
store a phone number
You can store a phone number or LINC ID in
Find it: M > Contacts > [New Contact].
1 Enter a name for the new entry. Each
entry’s name can contain 20 characters.
2 Select a specific Ringer.
call a stored phone
number or LINC ID
3 Select a type for the entry (Mobile, Work1,
Work2, Home, Fax, Pager, or Other).To store a
LINC ID, choose LINC ID.
Shortcut: From the home screen press under Contcs
4 Enter the number for the entry.
Find it: M > Contacts.
5 Press - under Done when finished.
1 Scroll to the Contacts entry.
Tip: Before saving the entry, you can save
more information. You can store E-mail
addresses, IP addresses, or Talkgroup IDs.
You can assign each number a speed dial
number and voice name.
After you have saved the number, the new
Contacts entry is displayed.
Tip: In Contacts, enter the first letter of the
contact you want and your contact list will
jump to the first contact name starting
with the letter you typed.
2 If the Contacts entry contains more than
one number, press
left or right until
the type of number you want to call is
displayed (Mobile, LINC ID, Work 1, Work 2, Home,
3 If you chose a phone number, press O
to call the entry.
If you choose a LINC ID or Talkgroup ID,
press and hold the PTT button to call the
Tip: If the Contacts entry you scrolled to
contains a LINC ID, you can make an
InstantLINC Mobile to Mobile call to that LINC
ID by pressing and holding the PTT button,
even if the LINC ID is not the type of number
find your phone number
Find it: M > My Info.
Tip: Want to see your phone number or LINC
ID while you’re on a call? Press M > My Info.
text messages
Your phone sends text messages using
Mobile Originated Short Messaging Services
(MOSMS) and receives text messages from
other phones that are using MOSMS.
set it up
Before you begin using text messaging, you
may need to set up your signature, service
center number, and expiration information.
Shortcut: From the home screen press under Msg > Text Inbox > M > Text Msg Setup.
Find it: M > Messages > Text Inbox > M > Text
Msg Setup.
The following options become available:
Signature: Enter your signature (up to 11
characters long).
Srvc Cntr No: Enter the phone number of your
service center. If you do not know this
number, contact your service provider.
Expire After: This is the amount of time
messages you send are saved at the
service center if they cannot be delivered.
After this period, they are discarded.
Auto Clean Up: Set this option to On if you want
you phone to delete Sent messages.
If you set Auto Clean Up to On, select Clean Up After
to set the number of days after which sent
messages are deleted or the number of
messages to be kept.
Press - under Done to save the options you
receive a text message
1 To view the message press - under
2 To dismiss the message notification press
- under Back.
Note: If your phone is powered off when you
receive a text message, your phone notifies
you the next time you power it on. If you are
out of your coverage area, your phone alerts
you when you return to your coverage area.
Tip: While reading a text and numeric
message that contains a phone number, you
can press O to call that number.
read from the message center
1 From the home screen press - under
Msg > Text Inbox.
2 Select the message you want to read or
press the number of the message you
want to read. If the message fills more
than one screen, scroll to read it.
3 To save the message, press - under Back
or to reply to the message, press under Reply or to see all other choices,
including forwarding and deleting the
message, calling the sender, or storing
the sender’s number in Contacts, press M.
create and send text messages
1 From the home screen press - under
Msg > [Create Message].
Select Text Inbox, Text Outbox, or Drafts.
2 To address the message use the keypad
to enter the phone number of the person
you want to send the message to and
press O.
Press - under Browse and select Recent
Calls, Contacts or Memo and then the number
you want.
3 Select Msg: and enter the text of the
message or to use a quick note press under Browse and scroll to the quick note
you want.
4 Press M > Set Send Method and select Text,
Fax, X400, Paging, Email, ERMES, or Voice.
5 If you want to send the message, press
- under Send or to delete the message
without sending it, press - under Cancel.
Note: If you want to request confirmation
of delivery press M > Send & Confirm.
use drafts
When you save a message as a draft, it is
saved in the drafts folder.
Shortcut: From the home screen press under Msg > Drafts.
1 Select the draft you want to edit. You also
have the choice to create new text
messages from this menu.
2 To edit the fields you want to change,
follow step 2 through step 5 in “create
and send text messages” above.
resend text messages
Shortcut: From the home screen press under Msg > Text Outbox.
2 Press - under Delete.
3 Press - under Yes to confirm.
delete all unlocked sent messages
Shortcut: From the home screen press under Msg > Text Outbox.
1 Press M > Delete All.
2 Press - under Yes to confirm.
manage memory
1 Scroll to the message you want to resend
or press the number of the message you
want to resend.
Your text inbox, outbox, and drafts folder have
a set amount of memory available for storing
2 Press M > Resend.
The text inbox holds 20 messages. If the text
inbox is full, you cannot receive messages
until you delete some.
delete sent text messages
Shortcut: From the home screen press under Msg > Text Outbox.
1 Scroll to the message you want to delete.
The outbox and drafts folder share memory
space. Together they can hold 30 messages.
If the outbox and drafts folder memory is full,
you cannot send messages or save drafts
until you delete some.
To view the amount of memory available in
your Text Inbox, Drafts or Text Outbox:
Shortcut: From the home screen press under Msg.
Select Text Inbox, Drafts or Text Outbox and press under Memory
using your handset
as a modem
You can use your handset as a modem with a
laptop, handheld device, or desktop
computer. In order to use your handset as a
modem, you must create a wired connection
between your handset and the other device.
connect with a data cable
use a data cable to connect your handset to a
laptop, handheld device, or desktop
1 Pull out the connector
cover, and insert the
charger into the
connector on your phone
as shown.
2 Insert the data plug into
the data port of the other
3 Press - under Change.
4 Scroll to the baud rate for your location.
5 Press - under Select.
When used as a modem, your handset is
enabled for Packet Data transfer mode, which is
used for small file transfers such as Email.
Note: To use these services, you must install
the iDEN Wireless Data Services software
(available separately). For more information on
setting up your computer and your handset
for packet and circuit data calls, contact your
service provider.
main attractions
LINC features
Your phone can send and receive the
following items through LINC ID Mobile to
Mobile calls with other phones that have this
• Pictures1
• My Info
• Contact information
When you make or receive an InstantLINC
Mobile to Mobile call, your phone
automatically determines whether the phone
you are engaged in an InstantLINC Mobile to
Mobile call with is able to receive each of
1. Additional charges may apply.
main attractions
these items. Your phone saves this
information for as long as the LINC ID is on
your Recent Calls list or is saved in your Contacts.
Your phone updates the saved information
each time you make or receive a call to or
from that LINC ID.
You can turn your phone’s ability to send and
receive pictures on and off.
You cannot turn your phone’s ability to send
and receive My Info and contact information
on and off.
Note: You cannot send LINC feature items
during Talkgroup calls.
send pictures
send a picture during a call
This feature requires a subscription.
Please contact your sales representative or
SouthernLINC Wireless at 1-800-406-0151.
1 While in an InstantLINC Mobile to Mobile
call press - under Browse.
You can send pictures stored in My Pictures
through InstantLINC Mobile to Mobile calls.
The picture you send appears on the
InstantLINC Mobile to Mobile call recipient’s
3 Push the PTT button to send.
If the recipient accepts the picture, their
phone saves it.
The first time you send a stored picture after
turning the phone on, Picture Fees May Apply.
Continue? appears.
Note: You cannot make or receive
InstantLINC Mobile to Mobile calls while
transmitting or receiving a picture.
2 Select the picture you want to send.
Note: Pictures sent or received may be
up to 100 kb. You cannot make or receive
calls while transmitting a picture.
start a call by sending a picture
You can start a call by sending a picture that
you have previously received and is stored in
My Pictures.
Find it: M > My Pictures.
1 Press M > LINC View.
A list of Contacts and Recent Calls that have
LINC IDs and are able to receive pictures
main attractions
2 Select the name of the person you want
to send the picture to.
3 Push the PTT button to send the picture.
4 Wait while the picture is transmitted. The
InstantLINC Mobile to Mobile call is
temporarily interrupted while a picture is
When you see a message asking if you want
to accept the picture, press - under Yes to
accept or - under No to decline.
To stop the transmission before it is finished,
press - under Cancel.
5 When prompted, press the PTT button to
resume the InstantLINC Mobile to Mobile
Note: The first time you accept a stored
picture after turning the phone on, Picture Fees
May Apply. Continue? appears and you are
prompted to respond. Press - under Yes to
accept the picture.
receive a picture
clear a picture from the display
When someone sends you a picture, your
phone emits a tone or vibrates and a message
appears asking if you want to accept the
Pictures you receive are saved to your
phone’s memory. They are accessible
through My Pictures.
main attractions
If you want to remove a picture from your
phone’s display while still on a call, press M
> Clear Screen.
The picture will not appear on the display
again the next time you receive a call from the
person who sent it. This does not delete the
picture from your phone’s My Pictures.
turn sending pictures on and
5 Push the PTT button to send your
You can turn your phone’s ability to send and
receive pictures on and off.
set my info sending option
You can control what portion of the
information in My Info is sent and whether it is
sent automatically in every call or only when
you choose to send it.
Find it: M > Settings > InstantLINC > LINC View > On.
send My Info
1 While in an InstantLINC Mobile to Mobile
press M > LINC View My Info and push the
PTT button to send.
2 From the home screen press M > My Info
> M > LINC View My Info.
Find it: M > My Info > M > LINC View Setup > Info
To Send.
The information your phone sends always
includes My Name and LINC ID. You may also
send Line 1, Line 2, and Carrier IP, depending on
your sending options.
3 Enter the LINC ID of the person you want
to send your info to or press - under
automatic sending
To control whether you send your information
4 Select a contact number from your Recent
Calls, Contacts or Memo.
Find it: M > My Info > M > LINC View Setup >
Auto Send.
1 Select On or Off.
main attractions
2 When you make a call in which your
information is sent automatically, the
name you entered in the My Name field of
My Info appears on the display of the
recipient’s phone, even if your name and
LINC ID are not stored in the recipient’s
send contact information
1 From the home screen press - under
Contcs and select the contact information
you want to send.
2 Press M > LINC View Contact.
3 Enter the LINC ID of the person you want
to send the contact info to or press under Browse. Select a contact number
from your Recent Calls, Contacts or Memo.
4 Push the PTT button to send the contact
main attractions
one touch PTT
Find it: M > Settings > InstantLINC > One Touch PTT
One Touch PTT sets your phone to do any of
the following each time you push the PTT
Off — Nothing happens if you push the PTT
button when the phone is in idle mode.
Last Call — Call the most recent LINC ID in
the recent calls list.
Assigned Number — Call a LINC ID you assign.
Enter the number using your keypad, or
press - under Search. Select Contacts, Recent
Calls or Memo.
Note: If you are entering a Talkgroup
number, press # before the number.
surveillance profile
When the unit is set to Surveillance
mode, it DOES NOT turn on its backlight,
make sounds or vibrate. This setting is
designed for public safety, the unit will only
ring through an earbud or headset and will
only show an incoming call message on the
Find it: M > Profiles > Surveillance.
1 Insert the earpiece or headset when
prompted to do so and press O.
Note: Surveillance profile works better
with a Motorola OriginalTM Surveillance
Earpiece for concealed hands-free
operation and high audio quality, sold
2 The phone is now operating in
surveillance mode.
main attractions
See page 1 for a basic phone diagram.
status indicators
Status indicators are shown at the top of the
home screen:
The home screen shows when you turn on
the phone. To dial a number from the home
screen, press number keys and O.
1. 2. 3. 4. 5. 6. 7.
Note: Your home screen may look different.
1 Signal Strength Indicator: Vertical bars
show the strength of the network
connection. You can’t make or receive
calls when 1 or 0 shows.
Soft key labels - show the current soft key
functions. For soft key locations, see page 1.
2 Active Phone Line: 1 indicates phone line
1 is ready to make calls; 2 indicates phone
line 2 is ready to make calls.
text entry
3 Speaker On/Off: Sounds associated with
InstantLINC Mobile to Mobile calls and
group calls are set to come through the
earpiece rather than through the speaker.
Your phone provides convenient ways to
enter words, letters, punctuation, and
numbers whenever you are prompted to
enter text (for example, when adding a
Contacts entry or when text messaging).
4 Ringer Off: Your phone is set to not ring.
5 Message Indicator: Shows when you
receive a text message.
6 Packet Data: Your handset is ready to
transfer packet data or is transferring
packet data.
Some features let you enter text.
change the character input method
1 When you see a screen where you can
enter text, press M to change the
character input method.
7 Battery Charge Indicator: A fuller battery
indicates a greater charge. Recharge the
battery when your phone shows Low
2 Select one of the following options:
entry methods
Press a key several times for
each characters.
Enter words using a predictive
text entering system that lets
you enter a word with fewer
key presses.
Enter symbols.
Enter numbers by pressing the
numbers on the keypad.
Languages Select the language in which
you want to write the message.
Tip: When entering text, press and hold #
to change letter capitalization (Abc > ABC > abc).
word method
Word English Text Input lets you enter text
into your phone by pressing keys just once
per letter.
Word English Text Input analyzes the letters
you enter using an intuitive word database
and creates a suitable word in the language
you are using to type the message. (The word
may change as you type.)
enter a word using Word Character
1 Select the Word character input method.
2 Press the corresponding keys once per
letter to enter a word (for example, to
enter the word Bill, press 2 4 5 5).
(If you make a mistake, press - under
Delete to erase a single character. Press
and hold - under Delete to delete an
entire entry.)
3 The database might find the word before
you finish typing. To accept a word and
insert a space, press #.
To accept a word completion (such as
Billion when you entered Bill), press
alpha method
To enter characters by tapping the keypad:
1 Select the Alpha method.
2 Press the corresponding keys repeatedly
until the desired letter appears. (For
example, to enter the word Bill, press 2
twice, 4 three times, 5 three times,
and 5 three times again. If you make a
mistake, press - under Delete to erase a
single character. Press and hold - under
Delete to erase an entire word.)
By default, the first letter of an entry is
capitalized and the following letters are lower
cased. After a character is entered, the cursor
automatically advances to the next space
after two seconds or when you enter a
character on a different key.
Characters scroll in the following order:
Space . 1 ? ! , @ & : ; “ - ( ) ‘ ¿ ¡ %
£ $¥
navigation key
Press the navigation key
up, down, left, or
right to scroll to items in
the display. When you
scroll to something,
press O.
handsfree speaker
You can use your phone’s handsfree speaker
to make calls without holding the phone to
your ear.
During a call (with the flip open), press under Speaker to turn the handsfree speaker
The handsfree speaker stays on until you
press - under Speaker or close the flip.
Note: The handsfree speaker won’t work
when your phone is connected to a handsfree
car kit or headset.
airplane mode
Note: Consult airline staff about the use of
Airplane Mode during flight. Turn off your
phone whenever instructed to do so by airline
Airplane mode turns off your phone’s calling
features in situations where wireless phone
use is prohibited. You can use the phone’s
other non-calling features when Airplane
Mode is activated.
Find it: M > Settings > Advanced > Airplane Mode >
features for the hearing
may need to adjust your hearing aid (HA)
volume setting.
using your phone with a
hearing aid
For best results use the following
optimization procedures and handset setting.
They generally apply as well for users with
cochlear implants:
optimize your handset position and
While in a phone call slide your phone up and
down, then left and right until best
microphone coupling is obtained. You also
If your HA has a telecoil, activate its switch,
then also rotate the handset as illustrated to
align the telecoils.
Note: Some automatically switched hearing
aids may need an auxiliary switching magnet.
If you are unsure whether your HA is telecoil
equipped or needs an auxiliary magnet,
please refer to your HA user guide or contact
a hearing aid professional or supplier.
Approximate telecoil location is within
6 -13 mm of this location.
Off - Shut off
M - Microphone
T - Telecoil
Approximate telecoil location is just
above the battery.
optimize your handset antenna
Your phone’s rating for Hearing Aid
compatibility is determined with the antenna
extended if it has an extendable antenna.
However, acceptable use might occur with
the antenna retracted. Test your handset in
both antenna positions when the handset is in
the optimum orientation.
choose your hearing aid setting
Find it: M > Settings > Phone Calls > Hearing Aid.
1 Set this option to Microphone. Microphone
coupling is now optimized.
2 Set this option to Telecoil. Handset meets
US federal requirements for telecoil
coupling sound.
3 Set this option to Off (factory default). This
is the setting for non Hearing Aid users.
To make and answer calls, see page 15.
recent calls
The recent calls list contains information
associated with calls you have made and
received and call alerts you have received.
When you send or receive InstantLINC
Mobile to Mobile calls, the recent call list
contains the following PTV items with those
• Contact information received
• My Info received
• Pictures sent or received.
The recent calls list displays up to 20 of the
most recent calls and call alerts.
1 Press M > Recent Calls.
2 Scroll through the list.
store an item to contacts from
recent calls
Phone calls, InstantLINC Mobile to Mobile
calls, My Info, or Contacts entries received
from other phones can be stored to the Contacts
list from the Recent Calls list.
Find it: M > Recent Calls.
1 Scroll to or select the item you want to
2 Press - under Store to save the
information as a new entry in the
Contacts list.
3 If Save is not one or your options, press M
> Update Contacts. And select the contact you
want to update.
4 Press - under Done to save your
To redial your last outgoing call, press and
hold O.
caller ID
Note: This feature requires a
subscription. Please contacts your sales
representative or SouthernLINC Wireless at
Caller ID allows people to identify a caller
before answering the phone by displaying the
number of the incoming call. If you do not
want your number displayed when you make
a call, just follow these easy steps.
To block your phone number from being
displayed for a specific outgoing call:
1 Press * 6 7.
2 Enter the number you want to call.
3 Press O.
To permanently block your number, call your
customer service provider.
call forward
Call forwarding sends calls to the phone
numbers you specify. You can forward all calls
to one number or forward missed calls to
different numbers depending on the reason
you missed the call. You can forward phone
lines 1 and 2 independently.
Find it: M > Call Forward.
1 To forward all calls select All Calls and
select To: to enter the phone number you
want all your calls forwarded to.
2 You can specify a forwarding number for
each type of missed call by selecting
Detailed and choosing the following options:
If Busy: When your handset is on a call or
transferring data.
If No Answer: When you do not answer on
the first 4 rings.
If Unreachable: When your handset is out of
coverage or powered off.
voice name
You can place calls by speaking commands to
your phone if you have previously assigned a
voice name to your contacts.
assign voice names to contacts
1 Press - under Contcs and select [New
2 Assign a name, phone number and select
3 Select Voice Name and follow the prompt to
record the voice name.
4 Press - under Back and - under Done.
place a call using voice name
With the flip closed or open, press the
speaker key t until you are prompted to say
the voice name.
The handset will automatically place the call.
emergency calls
Your service provider programs one or more
emergency phone numbers that you can call
under any circumstances, even when your
phone is locked or the SIM card is not
open sky and your local emergency response
center has the equipment to process location
information. Because of the limitations of this
feature, always provide your best knowledge
of your location to the emergency response
center when you make an emergency call.
Note: Emergency numbers vary by country.
Your phone’s preprogrammed emergency
number(s) may not work in all locations, and
sometimes an emergency call cannot be
placed due to network, environmental, or
interference issues.
Note: Emergency calls cannot be placed
while the keypad is locked.
Emergency phone calls can be made even
when your SIM card is blocked or not in your
Note: If you have not registered on the
network, emergency calls cannot be placed
while your SIM card is in your phone.
Dial 911 or your local emergency number to
be connected to an emergency response
center. If you are on an active call, you must
end it before making an emergency call.
When you make an emergency call, your
phone’s GPS Enabled feature can help
emergency service personnel find you, if you
are in a location where your phone's GPS
antenna has established a clear view of the
international calls
This feature requires a subscription. Please
contact your sales representative or
SouthernLINC Wireless at 1-800-406-0151.
speed dial
voice mail
Each phone number stored in Contacts is
assigned a Speed Dial number, which you can
use to call that number.
Note: To receive voice mail messages,
you must first set up a voice mail
account with SouthernLINC Wireless.
1 From the idle screen, use the keypad to
enter the Speed Dial number assigned to
the phone number you want to call.
receive a voice mail message
2 Press #.
3 Press O.
turbo dial
The first nine entries in your contacts are set
for turbo dial. They can be called by pressing
and holding the speed dial number
(1 through 9).
When you receive a voice mail message, New
VoiceMail Message appears on the display.
To call your service provider’s voice mail
system and listen to the message, press under Call.
To dismiss the message notification:
If the flip is closed, press the smart key . on
the top.
If the flip is open, press O, Back, or close the
If the caller leaves a message, this icon y
appears on the display, reminding you that
you have a new message.
This is an optional feature. Go to or contact
SouthernLINC Wireless at 1-800-406-0151
about its availability for purchase.
LINCaround allows direct two-way phone-tophone communications between two or more
phones equipped for LINCaround. You can
make and receive LINCaround calls even
when network service is not available. You
can talk to anyone on your code and channel
within your range.
Note: Range will vary based on terrain, manmade structures and atmospheric conditions.
LINCaround allows you to use code or private
mode operation, use up to 10 channels and
communicate with standalone LINCaround
Note: LINCaround is not compatible with
older Family Radio Services products.
The following features and main menu items
will not be available while in LINCaround
• On-network phone calls
• On-network InstantLINC Mobile to
Mobile calls
• Data transmission
• Incoming message notification
• Musical ring tones
• Call forwarding
• Messages
• Call Timers
• Call alerts
• Voice records
set your phone to LINCaround
exit LINCaround
Find it: M > LINCaround > Go To LINCaround.
Find it: M > LA Options > Exit LINCaround.
After a few seconds, the LINCaround idle screen
appears. The channel you are set to appears
on the first line of the display, the code you
are set to appears on the second line of the
display and LA Ready appears just above the
The following message displays: Switching to
Network Please Wait displays. After a few
seconds, the network idle screen appears.
Note: When switching from the network to
LINCaround, the last channel and code that were
set appear on the LINCaround idle screen.
While in LINCaround, this icon m appears on the
display, indicating that there is no network
signal and LINCaround is active.
Phones used in LINCaround mode should be
a minimum of 6 feet apart to maximize
performance and improve transmission range.
channels and codes
Your phone has 10 channels and 15 codes.
Channels are divided into sets of frequencies
that allow you to make and receive
LINCaround calls. Other parties may also be
talking on the same channel.
Codes help minimize interference from
unwanted messages and other disturbances
when you are on the same channel as others.
To have a conversation, all parties must be on
the same channel and code. For private
LINCaround calls, the person you are calling
must be in LINCaround and set to the same
channel to receive your call.
Note: When making a code call, all parties
that are on your code and channel can hear
your conversation.
3 Select a code number from 1 to 15 or one
of the following options:
Receive All
3 Select a channel number from 1 to 10.
Sets your phone to receive LINCaround
transmissions from any phone that is set to
the same channel, regardless of the code
(1-15). When you receive transmissions
with the code set to Receive All, the display
changes from Receive All to the code on
which the transmission was received.
4 When you are finished, press - under
Back to return to the LINCaround idle
Tip: You can reply to an incoming call within
6 seconds after hearing the short ending
beep by pressing the PTT button.
set a code
1 From the LINCaround idle screen, press
- under Edit.
Note: You cannot initiate a code call when
the code is set to Receive All. If you push the
PTT button with the code set to Receive All,
you will receive an error message.
set a channel
1 From the LINCaround idle screen, press
- under Edit.
2 Scroll to Channel and press - under Edit.
2 Scroll to Code and press - under Edit.
Pvt Only
make and receive code calls in
Allows you to have a private conversation
with another person using LINCaround.
When on a private LINCaround call, no
other parties can hear your conversation. In
order to make a private LINCaround call,
you must use the valid 10-digit Personal
Telephone Number (PTN) of the person you
are calling. The person you are calling must
be in LINCaround and set to the same
channel to receive your call.
To make a code call in LINCaround:
Note: An error message will occur if you
don’t use a valid PTN, or the person that
you are trying to reach is not in LINCaround,
or is set to a different channel or out of
4 When you are finished, press - under
Back to return to the LINCaround idle
1 Push and hold the PTT button. Transmit
appears on the first line of display. Begin
speaking after your phone emits the
LINCaround tone.
2 Release the PTT button to listen.
Note: The tone emitted from your phone
when using LINCaround is 4 beeps and
sounds different from the standard tone
heard with on-network InstantLINC
Mobile to Mobile and Talkgroup calls.
You could receive an error message if
there are no parties on your channel or
code, or if you are out of range.
When you receive a code call using
LINCaround, Receive appears on the first line of
the display.
Note: An incoming LINCaround call can be
terminated at any time by pressing o.
receive a private LINCaround
make a private LINCaround call
1 The number or name of the person who
initiated the call will appear in the first line
of the display.
1 Enter the 10-digit PTN of the person you
want to call on your channel, or press under Contacts and select a contact, or scroll
to a number in the recent calls list.
2 Push and hold the PTT button. Begin
speaking after your phone emits the
LINCaround tone.
3 Release the PTT button to listen.
The number or name of the person you are
calling will appear in the first line of the
2 You can reply within 6 seconds simply by
pushing the PTT button.
end a private LINCaround call
A private LINCaround call will end if there is
no communication for 6 seconds.
Note: A private LINCaround call may be
interrupted during the 6 second idle time by
another code call or private call.
make emergency calls while in
LINCaround mode
If you attempt to make an Emergency 911 call
while in LINCaround mode, your phone will
automatically exit LINCaround mode and
attempt to find a network signal.
Note: If you are out of network coverage your
phone will not be able to make an emergency
911 cellular call until you go back into the
network coverage area.
You must wait until the phone reconnects to
the network before attempting to make an
emergency 911 cellular call.
setup options
LINCaround setup options are available in the
LA Options screen in both network and
LINCaround modes.
access setup options in network
Find it: M > LINCaround> Setup.
access setup options in LINCaround
Find it: M > LA Options > Setup.
The following options become available:
Direct Launch
Launches your phone directly into
LINCaround when you select LINCaround
from the main menu. If Direct Launch is set to
On, you will not see LA Options when you
select LINCaround from the main menu. In
order to have access to your setup options,
Direct Launch must be set to Off. Or you can
access setup options while in LINCaround
by pressing M and selecting LA Options.
State Tone
Notifies you periodically with a tone that
you are in LINCaround mode. You can select a
time frame during which you want to be
notified that you are in LINCaround mode.
Select from 30 minutes, 1, 2, 3 or 4 hours.
ring tones
Press the volume
keys to:
To set the ring tone your phone makes when
you receive phone calls, call alerts, message
notifications, pictures sent in InstantLINC
Mobile to Mobile calls or Datebook
• turn off an
incoming call alert
• change the
earpiece volume
during calls
• change the ringer
volume from the
home screen
Tip: You can quickly set your ringer to
VibeAll by pressing and holding the
volume key down in the home screen.
Note: Only ring tones stored in your phone’s
memory are available in the ring tones list.
Not all audio files can be assigned as ring
Find it: M > Ring Tones
1 Make sure VibeAll is set to Off.
2 Scroll through the list of ring tones and
select the one you want to assign. Vibrate
sets your phone to vibrate instead of
making a sound; Silent sets your phone to
neither vibrate nor make a sound.
Tip: Highlighting a ring tone lets you hear
3 Select the features you want to assign the
ring tone to.
4 When you are finished, press - under
Note: This icon M appears on the display if
you set your phone to Silent. This icon Q
appears on the display if you set the phone to
set your phone to vibrate
You can set your phone to vibrate instead of
making a sound when you receive all phone
calls, InstantLINC Mobile to Mobile calls,
Talkgroup calls, call alerts, messages
notifications, pictures sent in InstantLINC
Mobile to Mobile calls, and Datebook
Find it: M > Ring Tones > VibeAll > On.
Shortcut: To set VibeAll to On using the volume
controls, press the volume controls to turn
down the volume as far as possible to set
VibeAll to On.
To set your phone to vibrate instead of
making a sound for some features but not
1 From the main menu, select Ring Tones.
2 Make sure VibeAll is set to Off.
3 Select Vibrate from the list of ring tones.
4 Select the features you want to set to
5 When you are finished, press - under
Set an image as a wallpaper (background) in
your phone’s home screen or throughout all
menu screens.
Find it: M > Settings > Display/Info > Wallpaper.
To select a wallpaper image scroll through the
list of pictures and press O to select the
picture of your choice.
Note: You can set the wallpaper to change
automatically after a certain period of time by
turning on the Auto Cycle feature located in the
Wallpaper menu.
Find it: M > Datebook > M > Setup.
You can view or change these options:
Start View: Sets Datebook to start in day view,
week view, or month view when you
access Datebook.
Daily Begin: Sets the beginning of your day.
This is the earliest time of day displayed in
week view, if you have a 12-hour day view.
Delete After: Sets the amount of time
Datebook waits to delete an event after it
Time Shift: Lets you shift the times of all
Datebook events. This is useful if you are
traveling to a different time zone.
Alert Timeout: Sets the amount of time a tone
continues to sound when you receive a
Datebook reminder.
Clock: Controls whether the time and date
appear on the idle screen; sets time and
date format; sets year.
hide or show
location information
Your phone is equipped with a Location
feature for use in connection with locationbased services that may be available in the
The Location feature allows the network to
detect your position. Turning Location off will
hide your location from everyone except 911.
Note: Turning Location on will allow the
network to detect your position using GPS
technology, making some applications and
services easier to use. Turning Location off
will disable the GPS location function for all
purposes except 911, but will not hide your
general location based on the cell site serving
your call. No application or service may use
your location without your request or
permission. GPS-enhanced 911 is not
available in all areas.
set your privacy options
Find it: M > GPS > Privacy.
Select from the following options:
Restricted: No Java or similar software
applications may view the location of your
phone. However, location information may
still be available to the phone’s owner, fleet
manager, or account administrator.
Unrestricted: All applications may view the
location of your phone, without notifying
By Permission: When an application attempts
to view the location of your phone, you will
be prompted to give permission. However,
location information may still be available to
the phone’s owner, fleet manager, or
account administrator.
other features
advanced calling
call waiting
To accept the second
call and put the active
call on hold press - under
To accept the second call
and end the active call press
Your phone rings with the
second call for you to
3-way call
Make or receive a
phone call and press
M > 3 Way. Enter the
second phone number,
press O and - under Join.
Tip: For quick ways to enter
the number, press M to
see the dialing menu.
You cannot make any other
calls after you have joined a
3-way call, even if one party
other features - advanced calling
any key
To make your handset to
answer and end calls by
opening and closing the flip
press M > Settings > Phone
Calls > Flip Activation.
Select Flip To Ans > On and Flip
to End > On.
To answer phone calls by
pressing any key on the
keypad press M > Settings >
Phone Calls > Any Key Ans > On.
other features—contacts
Press - under Contacts.
Select a contact and press
- under Edit. Change the
desired content and press
- under Done.
set ringer ID Press - under Contacts.
Select a contact and press
- under Edit > Ringer.
Select desired ringer and
press - under Done.
see datebook
Note: To improve GPS performance:
To create a new Datebook
event press M > Datebook >
[New Event].
To see a calendar event
press M > Datebook. Press
left or right to see the
day and
up or down to
see the events.
When an event reminder
occurs press - under View.
Press - under Back to close
the reminder.
• Stay in the open,
• Extend your phone's antenna
• Move away from other electrical or
electronic devices
• Remain stationary.
• Avoid touching the antenna with your
To see your approximate
approximate location press M > GPS >
Position. Scroll to view the
entire screen.
To recalculate position press
- under Rfrsh. This may
take several minutes.
other features - datebook
set GPS
To set the level of privacy
for your GPS system press
M > GPS > Privacy.
If your GPS PIN security
feature is enabled, enter
your GPS PIN and select the
privacy option you want.
change GPS Note: When you receive
your phone, your GPS PIN is
To change your GPS PIN
press M > Settings > Security
> Change Passwords > GPS PIN.
Enter the current GPS PIN
and enter the new 4- to 8digit GPS PIN. Re-enter the
new 4- to 8-digit GPS PIN to
other features—handsfree
Note: The use of wireless phones while
driving may cause distraction. Discontinue a
call if you can't concentrate on driving.
Additionally, the use of wireless devices and
their accessories may be prohibited or
restricted in certain areas. Always obey the
laws and regulations on the use of these
To activate the
speakerphone while driving
press and hold the
speakerphone key t or
press - under Speaker.
To automatically answer
calls when connected to a
car kit or headset press O
> Phone Calls > Auto Ans. Select
the amount of rings before
pc applications
other PC
For a list of complete PC
applications applications visit
time length
menu style
Set menu language:
Press O > Display/Info >
Select how long the display
screen and keypad are
Press O > Display/Info >
Show the main menu as
graphic icons or a text-based
Press O > Display/Info > Menu
Press O > Display/Info > Clock
> On
other features - pc applications
turn On TTY From the home screen
press M > Settings > Phone
Calls > TTY > Use TTY > On.
choose TTY From the home screen
press M > Settings > Phone
Calls > TTY > Type.
change the
TTY baud
Select from TTY, VCO or HCO.
From the home screen
press M > Settings > Phone
Calls > TTY > Baud.
Select 45.45 or 50.00
change TTY While in the TTY call, press
M > In Call Setup > TTY > Type.
during a call Select from TTY, VCO or HCO.
phone lock
To lock the phone press M
> Settings > Security > Phone Lock
> Lock Now or Auto Lock.
keypad lock To lock the keypad press M
> Settings > Security > Keypad Lock
> Lock Now or Auto Lock.
enable SIM
change SIM
Shortcut: To lock the
keypad press M > *
To enable SIM PIN, press
M > Settings > Security > SIM PIN
> On.
To change the SIM PIN,
press M > Settings > Security >
Change Passwords > SIM PIN.
Note: You can make emergency calls on a
locked phone (see page 39). A locked phone
other features—TTY
still rings or vibrates for incoming calls or
messages, but you need to unlock it to
other features - security
other features—security
Important Safety and
Legal Information
Safety and General Information
This section contains important information on the safe and
efficient operation of your phone. Read this information
before using your integrated multi-service portable radio.*
Safety Information
Exposure to Radio Frequency (RF)
Your phone contains a transmitter and receiver. When it is ON, it
receives and transmits RF energy. When you communicate with
your phone, the system handling your call controls the power level
at which your phone transmits.
Your Motorola phone is designed to comply with local regulatory
requirements in your country concerning exposure of human beings
to RF energy.
Portable Radio Product Operation and
EME Exposure
Your Motorola radio product is designed to comply with the
following national and international standards and guidelines
regarding exposure of human beings to radio frequency
electromagnetic energy (EME):
Safety Information
• United States Federal Communications Commission, Code
of Federal Regulations; 47 CFR part 2 sub-part J.
• American National Standards Institute (ANSI) / Institute of
Electrical and Electronics Engineers (IEEE). C95. 1-1992.
• Institute of Electrical and Electronics Engineers (IEEE).
C95. 1-2005 Edition.*
• International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
• Ministry of Health (Canada). Safety Code 6. Limits of
Human Exposure to Radio frequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz,
• Australian Communications Authority Radio
communications (Electromagnetic Radiation - Human
Exposure) Standard 2003.
• ANATEL, Brazil Regulatory Authority, Resolution 303 (July
2, 2002) "Regulation of the limitation of exposure to
* The information provided in this document supersedes
the general safety information in user’s guides
published prior to May 1, 2006
electrical, magnetic, and electromagnetic fields in the
radio frequency range between 9 kHz and 300 GHz."
"Attachment to Resolution 303 from July 2, 2002."
Operational Precautions
To assure optimal radio product performance and to be sure that
human exposure to RF does not exceed the guidelines set forth in
the relevant standards, always follow these instructions and
Phone Operation
When placing or receiving a phone call, hold your radio product as
you would a wireline telephone. Speak directly into the
Two-way radio operation
Your radio product has been designed and tested to comply with
national and international standards and guidelines regarding
human exposure to RF electromagnetic energy, when operated in
the two-way mode (at the face, or at the abdomen when using an
audio accessory) at usage factors of up to 50% talk/50% listen.
Transmit no more than the rated duty factor of 50% of the time. To
transmit (talk), push the PTT button. To receive calls, release the
PTT button. Transmitting 50% of the time or less, is important
because this radio generates measurable RF energy only when
transmitting (in terms of measuring for standards compliance).
When using your radio product as a traditional
two-way radio, hold the radio product in a
vertical position with the microphone one
to two inches (2.5 to 5 cm) away from the
If you wear a radio product on your body when
transmitting, always place the radio product in a Motorola
approved clip, holder, holster, case or body harness. If you do not
use a body-worn accessory supplied or approved by Motorola and
are not using the radio product in the intended use positions along
side the head in the phone mode or in front of the face in the
two-way radio mode, or if you hang your device from a lanyard
around your neck, keep the device at least 2.5 centimeters (1 inch)
from your body when transmitting.
Approved Accessories
For a list of approved Motorola accessories call 1-800-453-0920, or
visit our website at
RF Energy Interference/Compatibility
Nearly every electronic device is subject to RF energy interference
from external sources if inadequately shielded, designed or
otherwise configured for RF energy compatibility. In some
circumstances your handset may cause interference with other
Safety Information
Follow Instructions to Avoid Interference
your wireless phone with your implantable medical device, consult
your health care provider.
Turn OFF your radio product where posted notices instruct you to
do so.
In an aircraft, turn off your radio product whenever instructed to do
so by airline staff. If your radio product offers an airplane mode or
similar feature, consult airline staff about using it in flight.
Hearing Aids
Implantable Medical Devices
If you have an implantable medical devices, such as a pacemaker
or defibrillator, consult your physician before using this radio
Persons with implantable medical devices should observe the
following precautions:
• ALWAYS keep the phone more than 20 centimeters (8
inches) from the implantable medical device when the
phone is turned ON.
• DO NOT carry the phone in a breast pocket;
• Use the ear opposite the implantable medical device to
minimize the potential for interference.
• Turn OFF the phone immediately if you have any reason to
suspect that the interference is taking place.
Read and follow the directions from the manufacturer of your
implantable medical device. If you have any questions about using
Safety Information
Some phones may interfere with some hearing aids. In the event of
such interference, you may want to consult your hearing aid
manufacturer or physician to discuss alternatives.
Other Medical Devices and Health Care Facilities
If you use any other personal medical devices, consult your
physician or the manufacturer or your device to determine if it is
adequately shielded from RF energy. Turn off your radio product
when instructed to do so in hospitals or health care facilities that
may be using equipment that is sensitive to external RF energy.
Driving Precautions
Check the laws and regulations on the use of radio products in the
area where you drive. Always obey them.
When using your radio product while driving, please:
• Give full attention to driving and to the road. Using a
phone may be distracting. Discontinue a call if you can’t
concentrate on driving.
• Use hands free operation, if available.
• Pull off the road and park before making or answering a
call if driving conditions so require.
• Do not place a handset in the airbag deployment area.
Responsible driving practices can be found in the “Smart Practices
While Driving” section at the end of this guide and/or at the
Motorola Web site:
Note: The use of wireless phones while driving may cause
distraction. Discontinue a call if you can’t concentrate on driving.
Additionally, the use of wireless devices and their accessories may
be prohibited or restricted in certain areas. Always obey the laws
and regulations on the use of these products.
Operational Warnings
Batteries and Chargers
Caution: Improper treatment or use of batteries may present
a danger of fire, explosion, leakage, or other hazard. For
more information, see the “Battery Use and Battery Safety”
section in this user’s guide.
Your battery, charger, or portable radio may contain symbols,
defined as follows:
Obey all posted signs when using phones in public areas.
Potentially Explosive Atmospheres
Areas with potentially explosive atmospheres are often but not
always posted, and can include fueling areas such as below decks
on boats, fuel or chemical transfer or storage facilities, or areas
where the air contains chemicals or particles, such as grain, dust
or metal powders.
When you are in such area, turn off your handset, and do not
remove, install, or charge batteries unless it is a radio product type
especially qualified for use in such areas as “Intrinsically Safe” (for
example, Factory Mutual, CSA, or UL approved). In such areas,
sparks can occur and cause an explosion or fire.
Important safety information
Do not dispose of your battery
or phone in a fire.
Your battery or phone may
require recycling in
accordance with local laws.
Contact your local regulatory
authorities for more
Do not throw your battery or
phone in the trash.
Your phone contains an
internal lithium ion battery.
Safety Information
Do not let your battery,
charger, or phone get wet.
Listening at full volume to
music or voice through a
headset may damage your
Choking Hazards
Your portable radio or its accessories may include detachable
parts, which may present a choking hazard to small children. Keep
your device and its accessories away from small children.
If you have experienced seizures or blackouts, or if you have a
family history of such occurrences, please consult with your
physician before playing video games or enabling a flashing-lights
feature (if available) on your phone.
Discontinue use and consult a physician if any of the following
symptoms occur: convulsion, eye or muscle twitching, loss of
awareness, involuntary movements, or disorientation. It is always
a good idea to hold the screen away from your eyes, leave the
lights on in the room, take a 15-minute break every hour, and stop
use if you are very tired.
Caution About High Volume Usage
Listening at full volume to music or voice through a
headset may damage your hearing.
Glass Parts
Some parts of your phone may be made of glass. This glass could
break if the product is dropped on a hard surface or receives a
substantial impact. If glass breaks, do not touch or attempt to
remove. Stop using your phone until the glass is replaced by a
qualified service center.
Some people may be susceptible to epileptic seizures or blackouts
when exposed to flashing lights, such as when playing video
games. These may occur even if a person has never had a previous
seizure or blackout.
Safety Information
Repetitive Motion
When you repetitively perform actions such as pressing keys or
entering finger-written characters, you may experience occasional
discomfort in your hands, arms, shoulders, neck, or other parts of
your body. If you continue to have discomfort during or after such
use, stop use and see a physician.
Service & Repairs
If you have questions or need assistance, we’re here to help.
Go to, where you can select from a
number of customer care options. You can also contact the
Motorola Customer Support Center at 1-800-453-0920 (United
States), 1-877-483-2840 (TTY/TDD United States for hearing
Export Law Assurances
Export Law
This product is controlled under the export regulations of the
United States of America and Canada. The Governments of the
United States of America and Canada may restrict the exportation
or re-exportation of this product to certain destinations. For further
information contact the U.S. Department of Commerce or the
Canadian Department of Foreign Affairs and International Trade.
Export Law
Specific Absorption Rate Data
Your wireless phone is a radio transmitter and receiver. It is
designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government. These limits
are part of comprehensive guidelines and establish permitted
levels of RF energy for the general population. The guidelines are
based on standards that were developed by independent scientific
organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety
margin designed to assure the safety of all persons, regardless of
age and health.
The exposure standard for wireless mobile phones employs a unit
of measurement known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6W/kg.1 Tests for SAR are
conducted using standard operating positions reviewed by the FCC
with the phone transmitting at its highest certified power level in
all tested frequency bands. Although the SAR is determined at the
highest certified power level, the actual SAR level of the phone
while operating can be well below the maximum value. This is
because the phone is designed to operate at multiple power levels
so as to use only the power required to reach the network. In
Export Law
general, the closer you are to a wireless base station antenna, the
lower the power output.
Before a phone model is available for sale to the public, it must be
tested and certified to the FCC that is does not exceed the limit
established by the government-adopted requirement for safe
exposure. The tests are performed in positions and locations (e.g.,
at the ear and worn on the body) as required by the FCC for each
model. The highest SAR value for this model phone when tested
for use at the ear is 1.05 W/kg and when tested on the body, as
described in this user guide, is 1.15 W/kg during packet data
transmission. (Body-worn measurements differ among phone
models, depending upon available accessories and FCC
While there may be differences between the SAR levels of various
phones and at various positions, they all meet the government
requirement for safe exposure. Please note that improvements to
this product model could cause differences in the SAR value for
later products; in all cases, products are designed to be within the
Additional information on Specific Absorption Rates (SAR) can be
found on the Cellular Telecommunications Industry Association
(CTIA) web-site at or the Canadian Wireless
Telecommunications Association (CWTA) Web site:
1. In the United States and Canada, the SAR limit for mobile
phones used by the public is 1.6 watts/kg (W/kg) averaged over
one gram of tissue. The standard incorporates a substantial margin
of safety to give additional protection for the public and to account
for any variations in measurements.
2. The SAR information includes the Motorola testing protocol,
assessment procedure, and measurement uncertainty range for
this product.
Export Law
Motorola Limited Warranty for the United States and
What Does this Warranty Cover?
What Does this Warranty Cover?
Subject to the exclusions contained below, Motorola, Inc. warrants
its Motorola iDEN Digital Mobile and Portable Handsets
("Products"), Motorola-branded or certified accessories sold for
use with these Products ("Accessories") and Motorola software
contained on CD-Roms or other tangible media and sold for use
with these Products ("Software") to be free from defects in
materials and workmanship under normal consumer usage for the
period(s) outlined below. This limited warranty is a
consumer's exclusive remedy, and applies as follows to
new Products, Accessories and Software purchased by
consumers in the United States or Canada, which are
accompanied by this written warranty:
Products Covered
Length of Coverage
Products as defined
One (1) year from the date of
purchase by the first consumer
purchaser of the product.
Accessories as defined
One (1) year from the date of
purchase by the first consumer
purchaser of the product.
Products or
Accessories that are
Repaired or Replaced.
The balance of the original
warranty or for ninety (90)
days from the date returned to
the consumer, whichever is
Products Covered
Length of Coverage
Software as defined
above. Applies only to
physical defects in the
media that embodies the
copy of the software (e.g.
CD-ROM, or floppy disk).
Ninety (90) days from the
date of purchase.
What is not covered? (Exclusions)
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Ornamental Decorations. Ornamental decorations such as
emblems, graphics, rhinestones, jewels, gemstones and their
settings, and other decorative elements, are excluded from
Batteries. Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by
this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or neglect,
such as physical damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with liquid, water,
rain, extreme humidity or heavy perspiration, sand, dirt or the like,
extreme heat, or food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or Accessory to
abnormal usage or conditions; or (d) other acts which are not the
fault of Motorola, are excluded from coverage.
Use of Non-Motorola Products and Accessories. Defects or
damage that result from the use of Non-Motorola branded or
certified Products, Accessories, Software or other peripheral
equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, including without limitation, software
changes, or modification in any way by someone other than
Motorola, or its authorized service centers, are excluded from
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of tampering;
(c) mismatched board serial numbers; or (d) nonconforming or
non-Motorola housings, antennas, or parts, are excluded from
Communication Services. Defects, damages, or the failure of
Products, Accessories or Software due to any communication
service or signal you may subscribe to or use with the Products,
Accessories or Software is excluded from coverage.
Software Embodied in Physical Media. No warranty is made
that the software will meet your requirements or will work in
combination with any hardware or software applications provided
by third parties, that the operation of the software products will be
uninterrupted or error free, or that all defects in the software
products will be corrected.
Software NOT Embodied in Physical Media. Software that is
not embodied in physical media (e.g. software that is downloaded
from the internet), is provided "as is" and without warranty.
Who is covered? This warranty extends only to the first
consumer purchaser, and is not transferable.
What will Motorola Do? Motorola, at its option, will at no
charge repair, replace or refund the purchase price of any Products,
Accessories or Software that does not conform to this warranty.
We may use functionally equivalent
reconditioned/refurbished/pre-owned or new Products,
Accessories or parts. No data, software or applications added to
your Product, Accessory or Software, including but not limited to
personal contacts, games and ringer tones, will be reinstalled. To
avoid losing such data, software and applications please create a
back up prior to requesting service.
How to Obtain Warranty Service or Other Information? To
obtain service or information, please call:
Motorola iDEN Customer Services 1-800-453-0920 or
Or visit us online at
You will receive instructions on how to ship the Products,
Accessories or Software, at your expense, to a Motorola
Authorized Repair Center. To obtain service, you must include: (a) a
copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of
your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your
address and telephone number.
What Other Limitations Are There? ANY IMPLIED
Some states and jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or limitation on
the length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from
state to state or from one jurisdiction to another.
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola
software such as the exclusive rights to reproduce and distribute
copies of the Motorola software. Motorola software may only be
copied into, used in, and redistributed with, the Products
associated with such Motorola software. No other use, including
without limitation disassembly of such Motorola software or
exercise of the exclusive rights reserved for Motorola, is
Patent and Software Provisions
MOTOROLA will defend, at its own expense, any suit brought
against the end user purchaser to the extent that it is based on a
claim that the Product or parts infringe a United States patent, and
Motorola will pay those costs and damages finally awarded
against the end user purchaser in any such suit which are
attributable to any such claim, but such defense and payments are
conditioned on the following:
a.That MOTOROLA will be notified promptly in writing by such
purchaser of any notice of such claim;
b.That MOTOROLA will have sole control of the defense of
such suit and all negotiations for its settlement or
compromise; and
c.Should the Product or parts become, or in MOTOROLA'S opinion
be likely to become, the subject of a claim of infringement of a
United States patent, that such purchaser will permit MOTOROLA,
at its option and expense, either to procure for such purchaser the
right to continue using the Product or parts or to replace or modify
the same so that it becomes non-infringing or to grant such
purchaser a credit for the Product or parts as depreciated and
accept its return. The depreciation will be an equal amount per
year over the lifetime of the Product or parts as established by
MOTOROLA will have no liability with respect to any claim of
patent infringement which is based upon the combination of the
Product or parts furnished hereunder with software, apparatus or
devices not furnished by MOTOROLA, nor will MOTOROLA have
any liability for the use of ancillary equipment or software not
furnished by MOTOROLA which is attached to or used in
connection with the Product or any parts thereof.
Laws in the United States and other countries preserve for
MOTOROLA certain exclusive rights for copyrighted MOTOROLA
software, such as the exclusive rights to reproduce in copies and
distribute copies of such MOTOROLA software. MOTOROLA
software may be used in only the Product in which the software
was originally embodied and such software in such Product may
not be replaced, copied, distributed, modified in any way, or used
to produce any derivative thereof. No other use including, without
limitation, alteration, modification, reproduction, distribution, or
reverse engineering of such MOTOROLA software or exercise or
rights in such MOTOROLA software is permitted. No license is
granted by implication, estoppel or otherwise under MOTOROLA
patent rights or copyrights.
Hearing Aid Compatibility
A number of Motorola phones have been tested for hearing aid
compatibility. When some wireless phones are used with certain
hearing aids, users may detect a noise which can interfere with
the effectiveness of the hearing aid.
Some hearing aids are more “immune” than others to this
interference noise, and phones can also vary in the amount of
interference noise they may generate. ANSI standard C63.19 was
developed to provide a standardized means of measuring both
mobile phone and hearing aids to determine usability rating
categories for both.
Ratings have been developed for mobile phones to assist hearing
aid users find phones that may be compatible with their hearing
aid. Not all phones have been rated for compatibility with hearing
aids. Phones that have been rated have a label with the rating(s)
located on the box, and at
These ratings are not guarantees of compatibility. Results will vary
depending on the user's hearing aid and individual type and degree
of hearing loss. If a hearing aid is particularly vulnerable to
interference, even a phone with a higher rating may still cause
unacceptable noise levels in the hearing aid Trying out the phone
with your hearing aid is the best way to evaluate it for your
personal needs.
“M” Rating: Phones rated M3 or M4 meet FCC requirements for
hearing aid compatibility and are likely to generate less
interference to hearing aids than unrated phones. (M4 is the
“better” or higher of the two ratings.) On those models with an
extendable antenna, this rating is determined only with the
antenna extended.
“T” Rating: Phones rated T3 or T4 meet FCC requirements and are
likely to be more usable with a hearing aid's telecoil (“T Switch” or
“Telephone Switch”) than unrated phones. (T4 is the “better” or
higher of the two ratings.) On those models with a telecoil mode
setting, this rating is determined only with the phone so set. For
setting instructions, see “Features for the Hearing Impaired” in the
section entitled “Advanced Calling Features”. Note that not all
hearing aids have telecoils in them.
Hearing aids may also be measured for immunity to interference
from wireless phones and may have ratings similar to wireless
phones. Ask your hearing health care professional for the rating of
your hearing aid. Add the rating of your hearing aid and your phone
to determine the estimated usability:
• Any combined rating equal to or greater than six offers
excellent use.
• Any combined rating equal to five is considered normal
• Any combined rating equal to four is considered usable.
Thus, if you use an M3 phone with a M3 hearing aid you will have
a combined rating of six for “excellent use.” This methodology
applies equally for T ratings.
More information about hearing aid compatibility may be found at:,,, and
Information From the World Health Organization
WHO Information
Present scientific information does not indicate the need for any
special precautions for the use of mobile phones. If you are
concerned, you may want to limit your own or your children’s RF
exposure by limiting the length of calls or by using hands-free
devices to keep mobile phones away from your head and body.
Source: WHO Fact Sheet 193
Further information:
Product Registration
Online Product Registration:
Product registration is an important step toward enjoying your new
Motorola product. Registering helps us facilitate warranty service,
and permits us to contact you should your product require an
update or other service. Registration is for U.S. residents only and
is not required for warranty coverage.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola Personal Communications
Product you will need to provide a copy of your dated sales receipt
to confirm warranty status.
Thank you for choosing a Motorola product.
WHO Information
Wireless: The New Recyclable
Your wireless phone can be recycled. Recycling your phone
reduces the amount of waste disposed in landfills and allows
recycled materials to be incorporated into new products.
The Cellular Telecommunications Industry Association (CTIA) and
its members encourage consumers to recycle their phones and
have taken steps to promote the collection and environmentally
sound recycling of end-of-life devices.
California Perchlorate Label
Perchlorate Label
Some mobile phones use an internal, permanent backup battery on
the printed circuit board that may contain very small amounts of
perchlorate. In such cases, California law requires the following
“Perchlorate Material - special handling may apply. See”
There is no special handling required by consumer.
As a phone user, you have an important role in ensuring that this
device is recycled properly. When it comes time to give this phone
up or trade it in for a new one, please remember that the phone,
the charger, and many of its accessories can be recycled. It's easy.
To learn more about CTIA's Recycling Program for Used Wireless
Devices, please visit us at: index.html
Patent and Trademark Information
Patent and Trademark
MOTOROLA, the Stylized M Logo and all other trademarks
indicated as such herein are trademarks of Motorola, Inc. ® Reg.
U.S. Pat. & Tm. Off. © 2007 Motorola, Inc. All rights reserved.
Microsoft and Microsoft Internet Explorer are registered
trademarks of Microsoft Corporation.
T9 is a trademark owned by Tegic Communications.
T9® Text Input Patent and Trademark Information.
This product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541,
U.S. Pat. 6,011,554 and other patents pending.
Java and all other Java-based marks are trademarks or registered
trademarks of Sun Microsystems, Inc. in the U.S. and other
All other product names or services mentioned in this manual are
the property of their respective trademark owners.
Software Copyright Notice
The Motorola products described in this manual may include
copyrighted Motorola and third party software stored in
semiconductor memories or other media. Laws in the United
States and other countries preserve for Motorola and third party
software providers certain exclusive rights for copyrighted
software, such as the exclusive rights to distribute or reproduce
the copyrighted software. Accordingly, any copyrighted software
contained in the Motorola products may not be modified,
reverse-engineered, distributed, or reproduced in any manner to
the extent allowed by law. Furthermore, the purchase of the
Motorola products shall not be deemed to grant either directly or
by implication, estoppel, or otherwise, any license under the
copyrights, patents, or patent applications of Motorola or any third
party software provider, except for the normal, non-exclusive,
royalty-free license to use that arises by operation of law in the
sale of a product.
Patent and Trademark
Privacy and Data Security
Privacy and Data Security
Motorola understands that privacy and data security are important
to everyone. Because some features of your phone may affect your
privacy or data security, please follow these recommendations to
enhance protection of your information:
• Monitor access: Keep your phone with you and do not
leave it where others may have unmonitored access. Lock
your device’s keypad where this feature is available.
• Keep software up to date: If Motorola or a
software/application vendor releases a patch or software
fix for your phone which updates the device’s security,
install it as soon as possible.
• Erase before recycling: Delete personal information or
data from your phone prior to disposing of it or turning it in
for recycling. For step-by-step instructions on how to
delete all personal information from your device, please
contact your local service provider.
Privacy and Data Security
• Understanding AGPS: In order to comply with
emergency caller location requirements of the FCC, certain
Motorola phones incorporate Assisted Global Positioning
System (AGPS) technology. AGPS technology also can be
used in non-emergency applications to track and monitor a
user’s location, for example, to provide driving directions.
Users who prefer not to permit such tracking and
monitoring should avoid using such applications.
If you have further questions regarding how use of your phone may
impact your privacy or data security, please contact Motorola at, or contact your service provider.
Smart Practices While Driving
Drive Safe, Call Smart SM
Check the laws and regulations on the use of phones and
their accessories in the areas where you drive. Always
obey them. The use of these devices may be prohibited or
restricted in certain areas. Go to
for more information.
Your phone lets you communicate by voice and data, almost
anywhere, anytime, wherever wireless service is available and
safe conditions allow. When driving a car, driving is your first
responsibility. If you choose to use your phone while driving,
remember the following tips:
• Get to know your Motorola phone and its features
such as speed dial and redial. If available, these
features help you to place your call without taking your
attention off the road.
• When available, use a hands-free
device. If possible, add an additional
layer of convenience to your phone with
one of the many Motorola Original
hands-free accessories available today.
• Position your phone within easy reach. Be able to
access your phone without removing your eyes from the
Driving Safety
road. If you receive an incoming call at an inconvenient
time, if possible, let your voice mail answer it for you.
Let the person you are speaking with know you are
driving; if necessary, suspend the call in heavy
traffic or hazardous weather conditions. Rain, sleet,
snow, ice, and even heavy traffic can be hazardous.
Do not take notes or look up phone numbers while
driving. Jotting down a “to do” list or going through your
address book takes attention away from your primary
responsibility, driving safely.
Dial sensibly and assess the traffic; if possible,
place calls when your car is not moving or before
pulling into traffic. If you must make a call while
moving, dial only a few numbers, check the road and your
mirrors, then continue.
Do not engage in stressful or emotional
conversations that may be distracting. Make people
you are talking with aware you are driving and suspend
conversations that can divert your attention away from the
Use your phone to call for help. Dial 911 or other local
emergency number in the case of fire, traffic accident, or
medical emergencies.**
Driving Safety
• Use your phone to help others in emergencies. If you
see an auto accident, crime in progress, or other serious
emergency where lives are in danger, call 911 or other
local emergency number, as you would want others to do
for you.**
• Call roadside assistance or a special
non-emergency wireless assistance number when
necessary. If you see a broken-down vehicle posing no
serious hazard, a broken traffic signal, a minor traffic
accident where no one appears injured, or a vehicle you
know to be stolen, call roadside assistance or other
special non-emergency wireless number.*
* Wherever wireless phone service is available.
Driving Safety
accessories 9, 29
active phone line 31
advanced calling 53
3-way calls 53
call waiting 53
airplane mode 34
set 48, 49
turn off 48
answer a call 15
answer 15
any key answer 54
end 15
make 15
call forward 38
caller ID 38
center key 34
center select key 9
clock 57
contacts 54
edit/delete 54
set ringer ID 54
backlight 57
battery 13, 14
battery indicator 31
datebook 55
create events 55
customize 50
see events 55
view reminders 55
dial a phone number 15
dialed calls 37
display 30
Drafts 20
see also text messages,
earpiece volume 48
emergency number 39
end a call 15
end key 15
export regulations 67
flip 15
flip activation 54
frequently asked questions
service and repairs 67
GPS 55
approximate location 55
privacy options 56
GPS enabled
emergency calls 40
GPS, see GPS enabled
handsfree 56
auto answer 57
speaker-phone 56
handsfree speaker 34
Hearing Aid
using your phone with 35
Hearing Aid Compatibility 75
home screen 30
incoming call message 38
instant LINC 28
InstantLINC Mobile to
Mobile calls
answer 16
international calls 40
language 57
LINC features 24
LINCaround 42
channels 43
codes 43
emergency calls 46
private LINCaround
calls 46
setup options 47
low battery message 31
make a call 15
text messages 21
menu style 57
Message center
text messages 19
message indicator 31
using your handset
as a 22
navigation key 9, 34
optional accessory 9, 29
optional feature 9
packet data 31
PC applications 57
personalize 57
phone number 18
picture ID 38
power key 14
PTT features 24
PTV features
send My Info 27
send pictures 25
radio frequency 62
received calls 37
recent calls 37
recycling 78
redial 38
ring style indicator 31
ring style, setting 48
ring tones
off 48, 49
setting 48
vibrate 48, 49
ring tones, setting 48
ringer volume 48
radio frequency 62
RF energy interference 63
safety information 62
safety tips 81
security 58
send key 15
set 18
signal strength indicator 30
SIM card 10
change SIM PIN 58
enable SIM PIN 58
soft keys 30
speaker 31
speed dial 41
store your number 18
surveillance profile 29
tap text entry method 33
text 18
text entry 31
text messages 18
creating 20
deleting 21, 22
drafts 20
memory 21
message center 19
receiving 19
resend messages 21
sending 20
sent messages 21
setting up 18
TTY calls 58
turn on/off 14
using 35
voice mail
receiving 41
setting up 41
voice names 39
voicemail 41
voicemail message
indicator 41
volume 48
wallpaper 50
WHO information 77
your phone number 18