Eiki EIP-1600T Owner`s manual

EIP-1600T
OWNER’S MANUAL
EIKI INDUSTRIAL CO., LTD.
IMPORTANT
• For your assistance in reporting the loss
or theft of your Projector, please record
the Serial Number located on the bottom
of the projector and retain this information.
• Before recycling the packaging, please
ensure that you have checked the contents of the carton thoroughly against the
list of “Supplied accessories” on page 10.
Model No.: EIP-1600T
Serial No.:
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362
and of the same rating as above, which is also indicated on the pin
fuse marked or
face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket
outlet, as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol or coloured green or
green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked with
the letter N or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Before using the projector, please read this owner’s manual carefully.
Introduction
ENGLISH
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service
and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or recall that EIKI may be required to give under the 1972 Consumer
Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED
WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING:
High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the product.
FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
U.S.A. ONLY
1
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters
standby mode. During normal operation, when putting the projector into standby mode always
use the STANDBY-ON button on the projector or the STANDBY button on the remote control.
Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING
THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the owner’s manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
U.S.A. ONLY
• Consult the dealer or an experienced radio/TV technician for help.
Declaration of conformity
EIKI PROJECTOR, MODEL EIP-1600T
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Responsible Party:
EIKI INTERNATIONAL, INC.
30251 Esperanza Rancho Santa Margarita, CA 92688-2132
TEL: 800-242-3454
U.S.A. ONLY
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or, if you are
located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 54.
This EIKI projector uses a DMD panel. This very sophisticated panel contains 983,040 pixels
(micromirrors). As with any high technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain acceptable tolerances that the equipment
must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
2
How to Read this Owner’s Manual
■ The specifications are slightly different, depending on the model. However, you can connect and
operate all models in the same manner.
• In this owner’s manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display.
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
Adjustment buttons
(P/R/O/Q)
MENU button
MENU button
ENTER button
RETURN button
Buttons used in
this operation
• Press eRETURN to return to the previous
screen when the menu
is displayed.
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
Button used in
this step
• This operation can also be performed by using the buttons on the projector.
1
Press dMENU.
2
Press Q or O to select the menu
icon to adjust.
• The “Picture” menu screen for the selected input mode is displayed.
• The selected icon is highlighted.
Menu icon
Menu screen
Picture
Fine Sync
Options1
Example: “Picture” screen menu for INPUT 1
mode
Selected input mode
Menu icons
Picture
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
INPUT 1
Standard
0
0
0
0
0
0
0
On-screen
display
Options2
Note
• The “Fine Sync” menu is not available
for INPUT 3 or INPUT 4.
SEL./ADJ.
RETURN
ENTER
END
41
Info
........Indicates safeguards for using the projector.
Note .........Indicates additional information for setting up and operating the
projector.
For Future Reference
Maintenance
P. 51
Troubleshooting
PP. 60 and 61
Index
P. 64
3
Contents
Preparing
Introduction
Setup
How to Read this Owner’s Manual ....... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
Accessories ........................................ 10
Part Names and Functions ................. 11
Setting up the Projector ...................... 18
Inserting the Batteries .......................... 14
Usable Range ...................................... 15
Setting up the Projector ....................... 18
Standard Setup (Front Projection) ....... 18
Ceiling-mount Setup ............................ 18
Projection (PRJ) Mode ......................... 19
Picture (Screen) Size and Projection
Distance ............................................. 20
Quick Start
Connections
Quick Start .......................................... 16
Samples of Cables for Connection ..... 22
Connecting to Video Equipment ......... 23
Connecting to a Computer ................. 26
Controlling the Projector by a
Computer .......................................... 27
Using
Basic Operation
Turning the Projector On/Off .............. 28
Connecting the Power Cord ................ 28
Turning the Projector on ....................... 28
Turning the Power off (Putting the
Projector into Standby Mode) ........... 29
Image Projection ................................. 29
Switching the Input Mode .................... 29
Adjusting the Projected Image ............ 30
Correcting Trapezoidal Distortion ........ 32
Resize Mode ......................................... 36
Useful Features
Operating with the Remote Control .... 38
Shifting the Projected Image Vertically
(Image Shift) ...................................... 38
Switching the Iris Setting ..................... 38
Freezing a Moving Image .................... 38
Selecting the Picture Mode .................. 38
Menu Items ......................................... 39
Using the Menu Screen ...................... 41
Menu Selections (Adjustments) ........... 41
Picture Adjustment (“Picture” menu) .. 43
Selecting the Picture Mode .................. 43
Adjusting the Image ............................. 43
Adjusting the Color Temperature ......... 44
Adjusting the Colors ............................. 44
Progressive ........................................... 44
4
Reducing Image Noise (DNR) ............. 45
Switching the Iris Setting ..................... 45
Lamp Setting ........................................ 45
Computer Image Adjustment
(“Fine Sync” menu) ........................... 46
Adjusting the Computer Image ........... 46
Special Modes Setting ......................... 46
Auto Sync (Auto Sync Adjustment) ..... 46
Checking the Input Signal ................... 46
Using the “Options” Menu ................... 47
Adjusting the Image Position ............... 47
Adjusting the Overscan ....................... 47
Adjusting the Vertical Size of the Display
(Subtitle Setting) ................................ 47
Setting On-screen Display ................... 48
Setting the Video System ..................... 48
Signal Type Setting .............................. 48
Selecting the HDMI Setting .................. 48
Selecting the Background Image ........ 48
Auto Power Off Function ...................... 49
Checking the Lamp Life Status ........... 49
Reversing/Inverting Projected
Images ............................................... 49
Selecting the Transmission Speed
(RS-232C) .......................................... 50
Reducing the Power Consumption When
the Power Is in Standby Mode .......... 50
Fan Mode Setting ................................. 50
Returning to the Default Settings ......... 50
Selecting the On-screen Display
Language ........................................... 50
Reference
Appendix
Maintenance ....................................... 51
Maintenance Indicators ...................... 52
Regarding the Lamp ........................... 54
Lamp ..................................................... 54
Caution Concerning the Lamp ............ 54
Replacing the Lamp ............................. 54
Removing and Installing
the Lamp Unit .................................... 55
Resetting the Lamp Timer .................... 56
Connecting Pin Assignments ............. 57
RS-232C Specifications and Command
Settings ............................................ 58
Computer Compatibility Chart ............ 59
Troubleshooting .................................. 60
Specifications ..................................... 62
Dimensions ......................................... 63
Index ................................................... 64
5
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its installation,
use and servicing.
1. Read Instructions
All the safety and operating instructions should
be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be
retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be
followed.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example,
near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a
swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
9. Transportation
A product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
6
10. Ventilation
Slots and openings in the cabinet are provided
for ventilation to ensure reliable operation of the
product and to protect it from overheating, and
these openings must not be blocked or covered.
The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
11. Power Sources
This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your product dealer
or local power company. For products intended
to operate from battery power, or other sources,
refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with
a grounding terminal.
This plug will only fit into a grounding type
power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
14. Lightning
For added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the cable system.
This will prevent damage to the product due to
lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can
result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
17. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the
operating instructions, as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the product
to normal operation.
e. If the product has been dropped or damaged
in any way.
f. When the product exhibits a distinct change
in performance, this indicates a need for
service.
19. Replacement Parts
When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or
ceiling only as recommended by the
manufacturer.
22. Heat
This product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
• DLP\ (Digital Light Processing), DMD\ (Digital Micromirror Device) and BrilliantColor™
are trademarks of Texas Instruments, Inc.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
• All other company or product names are trademarks or registered trademarks of their
respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
7
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if lamp ruptures. In
case of lamp rupture, contact
your nearest EIKI Authorized
Dealer or Service Center for
replacement.
See “Replacing the Lamp” on
page 54.
Caution concerning the setup of the projector
■ For minimal servicing and to maintain high
image quality, EIKI recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by an EIKI Authorized Dealer or Service Center.
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
Warning about placing the projector in
a high position
■ When placing the projector in a high position,
ensure that it is secured carefully to avoid personal injury caused by the projector falling
down.
Do not subject the projector to hard impact and/or vibration.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Be sure to occasionally rest your eyes.
Do not set up the projector in places exposed to direct sunlight or bright light.
Avoid locations with extremes of temperature.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
■ The operating temperature of the projector is
from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Caution regarding placing of the projector
■ Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Be sure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into standby mode to prevent overheat
damage. This does not indicate a malfunction. (See pages 52 and 53.) Remove the projector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
■ Place the projector on a level site within the
adjustment range (8 degrees) of the adjustment foot.
■ After the projector is purchased, a faint smell
from the vent may appear when the power is
first turned on. This is normal and is not a
malfunction. It will disappear after the projector is used for a while.
8
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 4,900 feet (1,500 meters)
or more)
Do not block the exhaust and intake
vents.
■ When turning off the projector, the cooling fan
runs to decrease the internal temperature for
a while. Unplug the power cord after the cooling fan stops. The period the cooling fan runs
will vary, depending on the circumstances and
the internal temperature.
Caution regarding usage of the projector
■ When using the projector, be sure not to subject it to hard impact and/or vibration, as this
can result in damage. Take extra care with
the lens. Before moving the projector, be sure
to unplug the power cord from the wall outlet,
and disconnect any other cables connected
to it.
■ Do not carry the projector by holding the lens.
■ When storing the projector, re-attach the lens
cap. (See page 11).
■ Do not expose the projector to direct sunlight
or place next to heat sources. Doing so may
affect the cabinet color or cause deformation
of the plastic cover.
Other connected equipment
■ When connecting a computer or other audiovisual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the owner’s manuals of the projector and the equipment to be connected for
instructions on how to make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, be sure
to use an appropriate power cord for the country you are in.
Temperature monitor function
■ If the projector starts to overheat due to setup
problems or blockage of the air vents, “
” and
” will illuminate in the lower left corner
“
of the picture. If the temperature continues to
rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after
a 90-second cooling-off period the projector will
enter standby mode. Refer to “Maintenance Indicators” on page 52 for details.
Info
• The cooling fan regulates the internal temperature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in
the fan speed. This does not indicate malfunction.
• Do not unplug the power cord during projection or cooling fan operation. This can cause
damage due to rise in internal temperature,
as the cooling fan also stops.
9
Accessories
Supplied accessories
Remote control
Video cable
(10' (3.0 m))
QCNWGA097WJPZ
Power cord*
(1)
For U.S. and
Canada, etc.
(6' (1.8 m))
QACCDA007WJPZ
Two R-03 batteries
(“AAA” size, UM/SUM-4,
HP-16 or similar)
DIN-D-sub
RS-232C adaptor
(5 57/64" (15 cm))
QCNWGA015WJPZ
Lens cap (attached)
• Owner’s manual
• Quick Guide
(2)
For Europe,
except U.K.
(6' (1.8 m))
QACCVA011WJPZ
* Use the power cord that corresponds to the wall outlet in your country.
Optional accessory
■ Lamp unit
10
AH-11201
Part Names and Functions
Numbers in Z refer to the main pages in this owner’s manual where the topic
is explained.
Projector
Top View
Power
indicator
28, 52
STANDBY-ON
button
For turning the
power on and
putting the
projector into
standby mode.
28
ENTER button
For setting
items selected
or adjusted on
the menu.
41
RESIZE button
For switching
the screen
size.
36
28, 52
Lamp indicator
52
Temperature warning
indicator
29
INPUT buttons (P/R)
For switching input mode
1, 2, 3, 4, 5 or 6.
41
MENU button
For displaying
adjustment and
setting screens.
41
Adjustment buttons
(P/R/O/Q)
For selecting menu items.
Front View
51
Intake vent
Focus ring
For adjusting
the focus.
30
30
Zoom ring
For enlarging/
reducing the picture.
HEIGHT
ADJUST
lever
30
15
Remote control
sensor (front)
Push both sides of the lens cap
to attach or remove.
11
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this owner’s manual where the topic is
explained.
Rear View
51
Exhaust vent
51
15
Remote control
sensor (rear)
AC socket
28
Connect the
supplied Power cord.
13
Kensington
Security Standard
connector
Intake vent
Rear adjustment
foot
31
Terminals
6
Terminal
12
5
4
1
2 3
7
Description
Page
1
INPUT 1, 2 terminal
Connecting video equipment with component output terminal (DVD
player, DTV decoder, DVD recorder with hard disc, etc.).
23
2
INPUT 3 terminal
Connecting video equipment with S-video output terminal (VCR, DVD
player, etc.).
24
3
INPUT 4 terminal
Connecting video equipment without S-video output terminal.
24
4
INPUT 5 terminal
■ Connecting the computer.
■ Connecting video equipment with component output terminal
(DVD player, DTV decoder, DVD recorder with hard disc, etc.).
26
5
INPUT 6 terminal
Connecting video equipment with HDMI output terminal.
25
6
RS-232C terminal
Connecting the computer to control the projector.
27
7
TRIGGER terminal
When the projector is turned on, a control signal (DC 12V) outputs from this
terminal. If an electric screen or other compatible device is connected, it
can be turned on when the projector is turned on.
—
Numbers in Z refer to the main pages in this owner’s manual where the topic is
explained.
28 ON button
For turning the power on.
STANDBY button
For putting the
projector into the
standby mode.
29
29 INPUT 1, 2, 3, 4, 5 and 6
KEYSTONE button
For entering the
Keystone Correction
mode.
32
41 MENU button
buttons
For switching to the
respective input modes.
For displaying adjustment
and setting screens.
41 Adjustment buttons
RETURN button
41
For returning to the
previous menu screen
during menu operations.
(P/R/O/Q)
• For selecting menu items.
• For adjusting the Keystone
Correction when in the
Keystone Correction mode.
41 ENTER button
AUTO SYNC button
For automatically
adjusting images
when connected to a
computer.
46
For setting items selected
or adjusted on the menu.
36 RESIZE button
RGB/COMP. button
48
For switching to the
respective input signal type.
For switching the screen
size (STRETCH, SIDE
BAR, etc.).
38 PICTURE MODE button
FREEZE button
For freezing images.
38
Backlight button
For lighting all buttons on the
remote control.
For selecting the appropriate
picture.
38 IRIS button
For switching “HIGH
BRIGHTNESS MODE”,
“MEDIUM MODE” and
“HIGH CONTRAST MODE”.
38 IMAGE SHIFT buttons
For shifting the projected
image vertically.
Using the Kensington Lock on the projector
• This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for instructions
on how to use it to secure the projector.
13
Part Names and Functions (Continued)
Inserting the Batteries
1
Press the P mark on the cover and slide it
in the direction of the arrow.
2
Insert the batteries.
3
Attach the cover and slide it until it clicks
into place.
• Insert the batteries making sure the polarities
correctly match the m and n marks inside the
battery compartment.
Incorrect use of the batteries may cause them to leak or explode. Please
follow the precautions below.
Caution
•
•
•
•
•
•
•
•
14
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
compartment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them
to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure that you first wipe them and then
remove them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
Usable Range
The remote control can be used to control the projector within the ranges shown in the illustration.
Remote control sensor (front)
30°
Remote
control signal
transmitters
Remote control sensor (rear)
30°
23n (7 m)
30°
Remote control
23n (7 m)
30°
Remote
control signal
transmitters
Remote control
Note
• The signal from the remote control can be reflected off a screen for easy operation. However, the
effective distance of the signal may differ depending on the screen material.
When using the remote control
• Ensure that you do not drop, expose to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp. In this case, move the projector
away from the fluorescent lamp.
15
Quick Start
This section shows the basic operation (projector connecting with the video equipment).
For details, see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the video equipment is explained using one example.
3
8
5
8 STANDBY button
STANDBY-ON
button
3 ON button
INPUT buttons
5 INPUT 4 button
7 KEYSTONE button
7 Adjustment buttons
(P/R/O/Q)
6
6
6
7 ENTER button
Focus ring
Zoom ring
HEIGHT
ADJUST lever
1. Place the projector facing a wall or a screen
_P. 18
2. Connect the projector to the video equipment and plug the power
_PP. 22–28
cord into the AC socket of the projector
To INPUT 4 terminal
Connect the audio output of
any video devices to an
appropriate audio device.
AC socket
3. Remove the lens cap and turn the projector on
On the
projector
16
On the remote
control
_P. 28
4. Turn the video equipment on and start playback
_P. 29
5. Select the INPUT mode
Select the “INPUT 4” using the INPUT buttons on the projector or the INPUT 4 button on the
remote control.
On the On the remote
On-screen display
control
projector
INPUT 4
• When pressing the INPUT buttons on the projector, input mode switches in the following
order: INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 INPUT6
• Pressing the INPUT buttons on the remote control also allows you to switch the input mode.
6. Adjust the focus, image size, and projector angle
1. Adjust the focus by
turning the focus ring.
2. Adjust the projection
image size by turning
the zoom ring.
Zoom ring
_PP. 30, 31
3. Adjust the projector
angle using the HEIGHT
ADJUST lever.
Focus ring
7. Correct trapezoidal distortion (GEOMETRIC ADJUSTMENT)
1.
2.
3.
4.
_PP. 32–35
Press c KEYSTONE on the remote control.
Press P/R/O/Q on the remote control to set the upper-left position of the projected image.
Press i ENTER on the remote control to set the position.
Follow steps 2 and 3 to also set the upper-right, lower-right, and lower-left positions of the
projected image.
• When you confirm the lower left position, the screen adjustments will be set and setup will
end.
8. Turn the Power off
_P. 29
Press the STANDBY-ON button on the projector or the STANDBY button on the remote control,
and then press the button again while the confirmation message is displayed, to put the projector
into standby mode.
On-screen Display
On the On the remote
control
projector
• Unplug the power cord from the AC outlet after the cooling fan stops.
17
Setting up the Projector
Setting up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet
flat and level. Doing so will eliminate the need for Keystone correction and provide the best image
quality.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according
to the desired picture size. (See page 20.)
Example of standard setup
Side View
Screen
H
Lens center
L
Note
• Refer to page 20 for additional information concerning “Picture (Screen) Size and Projection Distance”.
Ceiling-mount Setup
■ It is recommended that you use the optional
EIKI ceiling-mount bracket for this installation.
Before mounting the projector, contact your
nearest EIKI Authorized Dealer or Service
Center to obtain the recommended ceilingmount bracket (sold separately).
■ Invert the image by setting “Ceiling + Front”
in “PRJ Mode”. See page 49 for use of this
function.
18
Projection (PRJ) Mode
The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode
most appropriate for the projection setting in use. (You can set the PRJ Mode in “Options2” menu.
See page 49.)
■ Table mounted, front projection
■ Ceiling mounted, front projection
Menu item ➞ “Front”
Menu item ➞ “Ceiling + Front”
■ Table mounted, rear projection
(with a translucent screen)
■ Ceiling mounted, rear projection
(with a translucent screen)
Menu item ➞ “Rear”
Menu item ➞ “Ceiling + Rear”
Indication of the Projection Image Size and Projection Distance
Refer to page 20 for additional information concerning “Picture (Screen) Size and Projection Distance”.
Example: When using a wide screen (16:9)
Picture (Screen) Size
300"
261"
200"
"
"×98
"
87"×
70"× 49"
39"
52"×
29"
5'
(1 11
.8 "–
m 6'
– 11
2. "
7'
1
1
m
(2 1
)
.4 "–
m 9'
– 2"
2.
8
9'
m
)
(3 11
.0 "–
m 11
– '6
3. "
5
m
19
)
(6 '1
.0 0
m "–2
– 2
7. '1
0 1
29
m "
)
(9 '9
.1 "–
m 34
– '5
10 "
.5
m
)
100"
80"
60"
174
×147
Projection
Distance
19
Setting up the Projector (Continued)
Picture (Screen) Size and Projection Distance
The projection screen size varies according to the distance from the lens of the projector to the screen. Install the projector so that projected images are projected onto the
screen at the optimum size by referring to the table below. Use the values in the table
as a reference when installing the projector.
When using a wide screen (16:9) and projecting 16:9 image
Picture (Screen) size
Diag. [χ]
Width
Height
Projection distance [L]
Minimum [L1] Maximum [L2]
Distance from the lens center
to the bottom of the image [H]
Adjustable range of
image position [S]
300 (762 cm) 261 (664 cm)
147 (374 cm)
29 9 (9.1 m) 34 5 (10.5 m)
21 1/32 (53 cm)
4 29/32 (12.5 cm)
270 (686 cm) 235 (598 cm)
132 (336 cm)
26 9 (8.2 m) 3011 (9.4 m)
18 15/16 (48 cm)
4 13/32 (11.2 cm)
250 (635 cm) 218 (553 cm)
123 (311 cm)
24 9 (7.5 m) 28 8 (8.7 m)
17 17/32 (45 cm)
200 (508 cm) 174 (443 cm)
98 (249 cm) 1910 (6.0 m) 2211 (7.0 m)
14 1/64 (36 cm)
3 17/64 (8.3 cm)
150 (381 cm) 131 (332 cm)
74 (187 cm) 1410 (4.5 m) 17 2 (5.2 m)
10 33/64 (27 cm)
2 29/64 (6.2 cm)
100 (254 cm)
87 (221 cm)
49 (125 cm)
911 (3.0 m) 11 6 (3.5 m)
7 1/64 (18 cm)
1 41/64 (4.2 cm)
80 (203 cm)
70 (177 cm)
39 (100 cm)
711 (2.4 m)
9 2 (2.8 m)
5 39/64 (14 cm)
1 5/16 (3.3 cm)
70 (178 cm)
61 (155 cm)
34 (87 cm)
611 (2.1 m)
8 0 (2.4 m)
4 29/32 (12 cm)
1 9/64 (2.9 cm)
60 (152 cm)
52 (133 cm)
29 (75 cm)
511 (1.8 m)
611 (2.1 m)
4 13/64 (11 cm)
63/64 (2.5 cm)
40 (102 cm)
35 (89 cm)
20 (50 cm)
4 0 (1.2 m)
4 7 (1.4 m)
2 51/64 ( 7 cm)
21/32 (1.7 cm)
χ : Picture (Screen) size (diag.) (in/cm)
L: Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
H: Distance from the lens center to the bottom of the image (in/cm)
S: Adjustable range of image position (in/cm) See page 47.
4 5/64 (10.4 cm)
The formula for picture size and projection distance
[m/cm]
[Feet/inches]
L1 (m) = 0.03019χ
L1 (ft) = 0.03019χ / 0.3048
χ
L2 (ft) = 0.03493 / 0.3048
L2 (m) = 0.03493χ
H (cm) = - 0.17808χ
H (in) = - 0.17808χ / 2.54
S (cm) = ±0.04151χ
S (in) = ±0.04151χ / 2.54
When using a normal screen (4:3) and projecting 4:3 image (SIDE BAR Mode)
Picture (Screen) size
Diag. [χ]
Width
Height
Projection distance [L]
Minimum [L1] Maximum [L2]
Adjustable range of
image position [S]
300 (762 cm) 240 (610 cm)
180 (457 cm) 36 4 (11.1 m) 42 1 (12.8 m) 25 47/64 (65 cm)
6 (15.2 cm)
270 (686 cm) 216 (549 cm)
162 (411 cm) 32 9 (10.0 m) 37 10 (11.5 m) 23 11/64 (59 cm)
5 13/32 (13.7 cm)
250 (635 cm) 200 (508 cm)
150 (381 cm) 30 4 (9.2 m)
35 1 (10.7 m) 21 29/64 (54 cm)
5 (12.7 cm)
200 (508 cm) 160 (406 cm)
120 (305 cm) 24 3 (7.4 m)
28 1 (8.6 m)
17 5/32 (44 cm)
150 (381 cm) 120 (305 cm)
90 (229 cm) 18 2 (5.5 m)
21 0 (6.4 m)
12 7/8 (33 cm)
100 (254 cm)
80 (203 cm)
60 (152 cm) 12 1 (3.7 m)
14 0 (4.3 m)
8 37/64 (22 cm)
2 (5.1 cm)
80 (203 cm)
64 (163 cm)
48 (122 cm)
9 8 (3.0 m)
11 3 (3.4 m)
6 55/64 (17 cm)
1 19/32 (4.1 cm)
70 (178 cm)
56 (142 cm)
42 (107 cm)
8 6 (2.6 m)
9 10 (3.0 m)
6 (15 cm)
1 13/32 (3.6 cm)
60 (152 cm)
48 (122 cm)
36 (91 cm)
7 3 (2.2 m)
8 5 (2.6 m)
5 9/64 (13 cm)
1 13/64 (3.0 cm)
40 (102 cm)
32 (81 cm)
24 (61 cm)
4 10 (1.5 m)
5 7 (1.7 m)
3 7/16 (9 cm)
51/64 (2.0 cm)
χ : Picture (Screen) size (diag.) (in/cm)
L: Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
H: Distance from the lens center to the bottom of the image (in/cm)
S: Adjustable range of image position (in/cm) See page 47.
20
Distance from the lens center
to the bottom of the image [H]
4 (10.2 cm)
3 (7.6 cm)
The formula for picture size and projection distance
[Feet/inches]
[m/cm]
L1 (ft) = 0.03694χ / 0.3048
L1 (m) = 0.03694χ
L2 (ft) = 0.04275χ / 0.3048
L2 (m) = 0.04275χ
H (in) = - 0.21794χ / 2.54
H (cm) = - 0.21794χ
χ
S (in) = ±0.0508 / 2.54
S (cm) = ±0.0508χ
When using a normal screen (4:3) and projecting 16:9 image
Picture (Screen) size
Diag. [χ]
Height
Width
Projection distance [L]
Distance from the lens center to Adjustable range of
the bottom of the image [H]
image position [S]
Minimum [L1] Maximum [L2]
300 (762 cm) 240 (610 cm)
180 (457 cm)
27 3 (8.3 m) 31 7 (9.6 m)
19 5/16 (49 cm)
4 1/2 (11.4 cm)
270 (686 cm) 216 (549 cm)
162 (411 cm)
24 7 (7.5 m) 28 5 (8.7 m)
17 3/8 (44 cm)
4 3/64 (10.3 cm)
250 (635 cm) 200 (508 cm)
150 (381 cm)
22 9 (6.9 m) 26 4 (8.0 m)
16 3/32 (41 cm)
3 3/4 (9.5 cm)
200 (508 cm) 160 (406 cm)
120 (305 cm)
18 2 (5.5 m) 21 0 (6.4 m)
12 7/8 (33 cm)
3 (7.6 cm)
150 (381 cm) 120 (305 cm)
90 (229 cm)
13 8 (4.2 m) 15 9 (4.8 m)
9 21/32 (25 cm)
2 1/4 (5.7 cm)
100 (254 cm)
80 (203 cm)
60 (152 cm)
9 1 (2.8 m) 10 6 (3.2 m)
6 7/16 (16 cm)
1 1/2 (3.8 cm)
80 (203 cm)
64 (163 cm)
48 (122 cm)
7 3 (2.2 m)
8 5 (2.6 m)
5 9/64 (13 cm)
1 13/64 (3.0 cm)
70 (178 cm)
56 (142 cm)
42 (107 cm)
6 4 (1.9 m)
7 4 (2.2 m)
4 1/2 (11 cm)
1 3/64 (2.7 cm)
60 (152 cm)
48 (122 cm)
36 (91 cm)
5 5 (1.7 m)
6 4 (1.9 m)
3 55/64 (10 cm)
29/32 (2.3 cm)
40 (102 cm)
32 (81 cm)
24 (61 cm)
3 8 (1.1 m)
4 2 (1.3 m)
2 37/64 (7 cm)
19/32 (1.5 cm)
χ : Picture (Screen) size (diag.) (in/cm)
L: Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
H: Distance from the lens center to the bottom of the image (in/cm)
S: Adjustable range of image position (in/cm) See page 47.
The formula for picture size and projection distance
[Feet/inches]
[m/cm]
L1 (ft) = 0.02771χ / 0.3048
L1 (m) = 0.02771χ
L2 (ft) = 0.03206χ / 0.3048
L2 (m) = 0.03206χ
χ
H (in) = - 0.16346 / 2.54
H (cm) = - 0.16346χ
S (in) = ±0.0381χ / 2.54
S (cm) = ±0.0381χ
Note
• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the
bottom of the image [H]”.
• Allow a margin of error in the values in the diagrams.
• Values with a minus (-) sign indicate the distance from the lens center below the bottom of the
image.
21
Samples of Cables for Connection
• For more details of connection and cables, refer to the owner’s manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Equipment
Audio-visual
equipment
Input
Signal
HDMI cable (commercially available)
Terminal on the
projector
INPUT6
Component cable (commercially available)
INPUT1, 2
S-video cable (commercially available)
INPUT3
Video cable (supplied)
INPUT4
Cables for a camera or a video game
INPUT1, 2
Cables for a camera or a video game
INPUT3
Cables for a camera or a video game
INPUT4
RGB cable (commercially available)
INPUT5
Cable
HDMI
video
Component
video
S-video
Video
Camera/
video game
Component
video
S-video
Video
Computer
RGB
video
22
Connecting to Video Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC
outlet and turn off the devices to be connected. After making all connections, turn on the
projector first and then the other devices.
When connecting the component video equipment to the component input terminal on the projector (INPUT1 or INPUT2)
To component output
(Y, CB/PB, CR/PR) terminal
DVD, etc.
To INPUT1 or INPUT2 terminal
Component cable
(commercially available)
23
Connecting to Video Equipment (Continued)
When connecting to equipment with S-video output terminal (INPUT3)
To S-video output terminal
DVD, etc.
To INPUT3 terminal
S-video cable
(commercially available)
When connecting to equipment with video output terminal (INPUT4)
Supplied
accessory
To video output terminal
Video cable
DVD, etc.
To INPUT4 terminal
Video cable
24
When connecting to equipment with HDMI output teminal (INPUT6)
HDMI is a new specialized interface capable of delivering a video and audio signal to
the terminal using just one cable. Since this projector does not support an audio signal
by itself, use an amplifier or other audio device.
For video connection, use a cable that conforms to HDMI standards. Using cables that
do not conform to HDMI standards may result in a malfunction.
To HDMI output terminal
HDMI compatible device
To INPUT6 terminal
HDMI cable (type A)
(commercially available)
Note
• HDMI (High Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
• Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the
digital video signal does not degrade when transmitted, and a high-quality image with a simple
connection can be enjoyed.
• When a DVI to HDMI conversion cable is connected to the HDMI terminal, a proper picture may not
be displayable.
25
Connecting to a Computer
When connecting a computer, ensure that it is the last device to be turned on after all the
connections are made.
Ensure that you have read the owner’s manuals of the devices to be connected before making
connections.
Computer
To RGB output terminal
Supplied
accessory
To INPUT5 terminal
RGB cable
(commercially available)
Note
• See page 59 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the
computer’s external output port is switched on. Refer to the specific instructions in the owner’s
manual of your computer to enable your computer’s external output port.
• The INPUT5 terminal is also compatible with a component video signal so that you can connect the
projector to a DVD player with a component output terminal. For details, contact your nearest EIKI
Authorized Dealer or Service Center.
26
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS232C adaptor and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. See page 58 for
detail.
When connecting to a computer using an RS-232C serial control cable and a DIND-sub RS-232C adaptor
Supplied
accessory
DIN-D-sub
RS-232C
adaptor
To RS-232C terminal
Computer
To RS-232C terminal
DIN-D-sub RS-232C
adaptor
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• See page 58 for connection of an RS-232C serial control cable.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This
may damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.
This may damage your computer.
27
Turning the Projector On/Off
Connecting the Power Cord
Supplied
accessory
Power cord
Plug the supplied power cord into the AC
socket on the rear of the projector.
AC socket
Info
Turning the Projector on
Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 23 to 28.)
Remove the lens cap and press
o STANDBY-ON on the projector or
bON on the remote control.
• English is the factory default language. If you
want to change the on-screen display to another
language, change the language according to
the procedure on page 50.
Lamp indicator
Power indicator
Note
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green: The lamp is warming up
or shutting down.
Red:The lamp is shut down abnormally
or the lamp should be replaced.
• When switching on the projector, a slight flickering of the image may be experienced within
the first minute after the lamp has been illuminated. This is normal operation as the lamp’s
control circuitry is stabilising the lamp output
characteristics. It should not be regarded as
faulty operation.
• If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to start projection.
28
STANDBY-ON button
ON button
STANDBY
button
Turning the Power off (Putting
the Projector into Standby Mode)
1
2
Press oSTANDBY-ON on the projector or aSTANDBY on the remote control, then press that button again while the confirmation
message is displayed, to put the
projector into standby mode.
Unplug the power cord from the AC
outlet after the cooling fan stops.
On-screen Display (confirmation message)
• The power indicator on the projector
blinks in red while cooling.
• The power indicator changes to green
when the projector finishes cooling.
R
Info
• Do not unplug the power cord during projection
or cooling fan operation. This can cause damage due to rise in internal temperature, as the
cooling fan also stops.
Image Projection
INPUT buttons
Switching the Input Mode
Select the appropriate input mode for
the connected equipment.
Press the appropriate INPUT button on
the remote control to select the desired
input mode.
• When pressing INPUT (P/R) on the projector,
input mode switches in the following order:
INPUT1
INPUT2
INPUT3
INPUT6
INPUT5
INPUT4
29
Image Projection (Continued)
Adjusting the Projected Image
Zoom ring
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Rotate the focus ring to adjust the focus while watching the projected image.
2 Adjusting the Screen Size
Focus ring
You can adjust the screen size using
the zoom ring on the projector.
Rotate the zoom ring to enlarge or
shrink the screen size.
3 Adjusting the Height
The height of the projector can be adjusted using the adjustment feet at the
front and rear of the projector.
When the screen is above the projector, the projection image can be made
higher by adjusting the projector.
1
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
2
Remove your hands from the
HEIGHT ADJUST lever of the projector after its height has been
finely adjusted.
HEIGHT
ADJUST lever
• The angle of projection is adjustable up
to 8 degrees from the surface on which
the projector is placed.
Make small
adjustments.
30
3
Use the rear adjustment foot to
make the projector level.
• The projector is adjustable ±1 degree
from the standard position.
Note
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the procedures in Keystone Correction to correct the
distortion. (See page 32.)
Rear adjustment foot
Info
• Do not apply too much pressure on the projector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.
31
Image Projection (Continued)
KEYSTONE
button
Correcting Trapezoidal
Distortion
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
There are the two types of the Keystone
Correction.
1) The “GEOMETRIC ADJUSTMENT”
method corrects trapezoidal distortion by specifying 4 marks on the
screen.
2) The “H & V KEYSTONE” method features corrections to 2 axes (horizontal and vertical) based on numerical
values.
32
Adjustment buttons
(P/R/O/Q)
RETURN button
ENTER button
Selecting the Type of
Correction
Select the Keystone correction method.
Press c KEYSTONE on the remote control.
• “GEOMETRIC ADJUSTMENT” will be
displayed.
• Each time c KEYSTONE is pressed, the
display toggles as follows:
GEOMETRIC
ADJUSTMENT
H & V KEYSTONE
The display disappears.
Note
• When corrections are made with Keystone correction, the changes are saved even if the
power cord is unplugged.
• Since Keystone correction digitally corrects
the signal, resolution may slightly decrease
when it is used. Moiré patterns and line distortions may also be visible in detailed images.
However, this is not a malfunction.
• If you cannot correct trapezoidal distortion with
Keystone correction, change the placement
position of the projector.
• Straight lines and the edges of the displayed
image may appear jagged, when adjusting the
Keystone setting.
• Also read “About Copyrights” on page 37.
GEOMETRIC
For correcting an image by
ADJUSTMENT designating the corner of the
projected image.
(See page 34.)
H&V
KEYSTONE
For correcting an image by
designating the horizontal or
vertical axes. (See page 35.)
33
Image Projection (Continued)
GEOMETRIC ADJUSTMENT
R On-screen display
Note
• To use the “GEOMETRIC ADJUSTMENT”, set
RESIZE to “STRETCH”. (See page 36.)
1
Press c KEYSTONE on the remote control repeatedly until
“GEOMETRIC ADJUSTMENT” is
displayed.
2
Adjust the focus, size, and projection angle so that the screen
edges line up into the blue area.
• Line up the screen edges into the blue
area as closely as possible.
3
Press P, R, O or Q to move the
position for the upper left of the
image.
Adjust upper left corner
GEOMETRIC ADJUSTMENT
ADJUST
RESET
NEXT
END
Geometric Adjustment
Blue
Upper Right
area Screen Upper Left
• Adjust the screen until the displayed red
arrows line up in the upper left.
4
Press i ENTER to set the position.
• The arrow in the upper right turns red.
5
Repeat the same procedure with
the positions for the upper right,
lower right and lower left of the
image.
• When you press e RETURN at this point,
you will return to the previous screen.
• If you press e RETURN before adjusting the upper left corner, the Reset Confirmation screen displays.
• When you confirm the lower left position, the screen adjustments will be set
and the “GEOMETRIC ADJUSTMENT”
mode will end.
Note
• The placement of the screen and the projector
may result in the image aspect ratio becoming
slightly distorted.
34
Lower Left
Lower Right
H & V KEYSTONE
1
2
Project the image and adjust the
focus, image size, and projection
angle.
Press c KEYSTONE on the remote control repeatedly until “H &
V KEYSTONE” is displayed.
R On-screen display
H&V KEYSTONE
END
ADJUST
ENTER
RESET
• When the “GEOMETRIC ADJUSTMENT”
mode has been used to adjust the image, a confirmation screen displays before the “H & V KEYSTONE” screen, asking if you want to reset the adjustments
or not. Then select RESET.
3
Press P or R on the remote control to align the left and right sides
of the projected image.
4
Press O or Q on the remote control to align the upper and lower
sides of the projected image.
5
Press c KEYSTONE or i ENTER
on the remote control and the
“H&V KEYSTONE” mode ends.
Vertical Keystone Correction
(Adjustment with P / R)
Horizontal Keystone Correction
(Adjustment with O / Q)
Note
• If adjustments are made using both “H KEYSTONE” and “V KEYSTONE” at the same time,
the image aspect ratio may become slightly
distorted.
• When adjusting “H KEYSTONE” and “V KEYSTONE” at the same time, the values of adjustable angles for each setting become smaller.
• The adjustable value of the “V KEYSTONE”
becomes extremely small when “H KEYSTONE” is made to be the maximum value.
35
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose “STRETCH”, “SIDE BAR”, “CINEMA ZOOM” or “DOT
BY DOT (Computer input only)” image.
Press
RESIZE on the projector or jRESIZE on the remote control.
On the projector
On the remote control
RESIZE button
RESIZE button
VIDEO
• “STRETCH” is fixed when 540P, 720P or 1080I signals are entered.
Input Signal
DVD / Video
Output screen image
Image type
STRETCH
4:3 aspect ratio
480I, 480P, 576I,
576P, NTSC, PAL,
SECAM
Letter box
Squeezed
16:9 aspect ratio
540P, 720P, 1080I
16:9 aspect ratio
: Cutout area on which images cannot be projected.
36
SIDE BAR
CINEMA ZOOM
Computer
Input Signal
Computer
Output screen image
Image
type
STRETCH
SIDE BAR
CINEMA
ZOOM
DOT BY DOT
Resolution lower than
XGA
4:3 aspect
ratio
XGA
(1024K768)
4:3 aspect
ratio
1280K720
16:9 aspect
ratio
: Cutout area on which images cannot be projected.
About Copyrights
• When using the RESIZE function to select an image size with a different aspect ratio
to a TV program or video image, the image will look different from its original appearance. Keep this in mind while choosing an image size.
• The use of the Resize, Keystone Correction, Subtitle, or Overscan function to compress or stretch the image for commercial purposes/public displays in a café, hotel,
etc. may be an infringement of copyright protected by law for copyright holders. Please
use caution.
• While watching non-widescreen images (4:3), if you use the RESIZE function to fill
the screen or use the Overscan function to change the aspect ratio of a fixed-ratio
input signal, parts of the outer edge of the image will be cut off or distorted. To watch
original images as the producers intended, set RESIZE to “SIDE BAR” and Overscan
to its default setting.
37
Operating with the Remote Control
Shifting the Projected Image Vertically (Image Shift)
IMAGE SHIFT
buttons
For easier viewing, this function shifts
the entire image projected on the
screen up or down when projecting 16:9
images from DVD players or other connected devices.
PICTURE
MODE button
Press PIMAGE SHIFT.
• The image moves up.
Press RIMAGE SHIFT.
IRIS button
• The image moves down.
Note
FREEZE button
• The Image Shift function operates when
“Resize” is not set to “DOT BY DOT”.
• For details on Image Shift, see page 47.
Switching the Iris Setting
This function controls the quantity of
the projected light and the contrast of
the image.
Press lIRIS.
• Each time the button is pressed while the display is on, the mode is switched in the following order:
HIGH BRIGHTNESS MODE
MEDIUM MODE
HIGH CONTRAST MODE
Note
• For details on Iris, see page 45.
Selecting the Picture Mode
You can select the appropriate picture
mode to best match the projected image you are watching.
Press kPICTURE MODE.
Freezing a Moving Image
38
1
Press hFREEZE.
2
Press hFREEZE again to return
to the moving image from the currently connected device.
• The projected image is frozen.
• When pressing kPICTURE MODE, the picture
mode changes in the following order:
Standard
Natural
Dynamic
Memory
Movie2
Movie1
Note
• See page 43 for details on the picture mode.
Menu Items
The following shows the items that can be set in the projector.
The selectable items vary depending on the selected input, input signals, or adjustment
values. Items that cannot be selected will be greyed out.
Main menu
“Picture” menu
Sub menu
Picture
Page 43
PAGE 1
Picture
Page 43
INPUT 1
Standard
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
0
0
0
0
0
0
0
SEL./ADJ.
RETURN
Contrast
-30
+30
Bright
-30
+30
Color
-30
+30 *2
Tint
-30
+30 *2
Sharp
-30
+30 *2
Red
-30
+30
Blue
-30
+30
Page 43
ENTER
END
PAGE 2
5500K
6500K
7500K
8500K
9300K
10500K
CLR Temp
Picture
INPUT 1
Picture Mode
CLR Temp
BrilliantColor™
C. M. S.
Progressive
DNR
IRIS
Lamp Setting
Reset
Standard
Natural
Dynamic
Movie1
Movie2
Memory
Picture Mode
Page 44
Standard
7500K
1
BrilliantColor™ [0/1/2]
Page 43
3D Progressive
Level 1
High Brightness
Bright
C.M.S.
*1
Page 44
Progressive
2D Progressive
3D Progressive
Film Mode
*2
Page 44
SEL./ADJ.
RETURN
Single ADJ
END
DNR
OFF
Level 1
Level 2
Level 3
Page 45
IRIS
“C.M.S.”
High Brightness
Medium Mode
High Contrast
Page 45
Lamp Setting
C. M. S.
C. M. S. - Hue
C. M. S. - Saturation
C. M. S. - Value
Reset
Reset
*1
R
Y
G
C
B
M
Reset
SEL./ADJ.
RETURN
Bright
Eco + Quiet
Page 45
0
0
0
0
0
0
C.M.S.-Hue
R
-30
+30
Page 44
Y
-30
+30
C.M.S.-Saturation
G
-30
+30
Page 44
C
-30
+30
B
-30
+30
M
-30
+30
C.M.S.-Value
ENTER
END
Page 44
Reset
Reset
*1 When the Progressive mode is set to “3D Progressive” or
“Film Mode”, the C.M.S. function cannot be used.
*2 Item that cannot be set when inputting an RGB signal
through INPUT 5 or INPUT 6.
39
Menu Items (Continued)
Main menu
“Fine Sync” menu
Fine Sync
Page 46
Fine Sync
INPUT 5
Clock
Phase
H-Pos
V-Pos
Reset
Special Modes
Auto Sync
Sub menu
Clock
-150
Page 46
Phase
-30
H-Pos
-150
+150
Page 46
V-Pos
1080I
On
-60
+60
Page 46
Reset
Cur. sig. freq : H 33.8 kHz / V 60 Hz
Special Modes
1035I
1080I
Page 46
ENTER
END
Auto Sync [On/Off]
Page 46
• The “Fine Sync” menu is not available for
INPUT 3 or INPUT 4.
Cur. sig. freq
Main menu
Options 1
Page 47
Page 46
Image Shift
-24
Sub menu
+24
Page 47
Overscan H
Overscan V
“Options1” menu
-30
-30
+30
+30
Page 47
Subtitle
Options 1
Image Shift
Overscan H
Overscan V
Subtitle
OSD Display
Video System
Signal Type
HDMI Setting
Background
Auto Power Off
Lamp Timer(Life)
SEL./ADJ.
RETURN
+30
Page 46
0
0
0
0
SEL./ADJ.
RETURN
+150
INPUT 1
-30
+30
Page 47
0
0
0
0
OSD Display [On/Off]
Page 48
Video System
On
Auto
Auto
Standard
Blue
On
0 h
100%
ENTER
END
Page 48
Signal Type
Page 48
HDMI Setting
Page 48
*1 Item that can be set when using INPUT 3 or
INPUT 4.
*2 Item that can be set when using IINPUT 5 or
INPUT 6.
Background
Page 48
*1
*2
Auto
PAL
SECAM
NTSC 4.43
NTSC 3.58
PAL-M
PAL-N
PAL-60
Auto
RGB
Component
Standard
Enhanced
Blue
None
Auto Power Off [On/Off]
Page 49
Lamp Timer(Life)
Page 49
Main menu
Options2
Page 49
“Options2” menu
Sub menu
PRJ Mode
Page 49
RS-232C
Options 2
PRJ Mode
RS-232C
STANDBY Mode
Fan Mode
All reset
Language
INPUT 1
Front
9600 bps
Eco
Normal
English
Page 50
STANDBY Mode
Page 50
Fan Mode
Page 50
Front
Ceiling + Front
Rear
Ceiling + Rear
9600bps
115200bps
Standard
Eco
Normal
High
All reset
Page 50
Language
Page 50
SEL./ADJ.
RETURN
40
ENTER
END
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
Adjustment buttons
(P/R/O/Q)
MENU button
MENU button
ENTER button
RETURN button
• Press eRETURN to return to the previous
screen when the menu
is displayed.
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
1
Press dMENU.
2
Press Q or O to select the menu
icon to adjust.
• The “Picture” menu screen for the selected input mode is displayed.
• The selected icon is highlighted.
Menu icon
Menu screen
Picture
Fine Sync
Options1
Example: “Picture” screen menu for INPUT 1
mode
Selected input mode
Menu icons
Picture
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
INPUT 1
Standard
0
0
0
0
0
0
0
Options2
Note
• The “Fine Sync” menu is not available
for INPUT 3 or INPUT 4.
SEL./ADJ.
RETURN
ENTER
END
41
Using the Menu Screen (Continued)
3
Press P or R to select the item to
adjust.
• The selected item is highlighted.
Picture
INPUT 1
Standard
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
0
0
0
0
0
0
0
SEL./ADJ.
RETURN
Single ADJ
END
Items to be adjusted
To adjust the projected
image while watching it
Press iENTER.
• The selected item (e.g. “Bright”) is displayed by itself at the bottom of the
screen.
• When pressing P or R, the following item
(“Color” after “Bright”) will be displayed.
The item displayed by itself
Picture
INPUT 1
Bright
SEL./ADJ.
RETURN
0
Rtn. Menu
END
Note
• Press iENTER again to return to the
previous screen.
4
Press O or Q to adjust the item
selected.
• The adjustment is stored.
Picture
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
SEL./ADJ.
RETURN
5
INPUT 1
Standard
0
15
0
0
0
0
0
Single ADJ
END
Press dMENU.
• The menu screen will disappear.
Note
• The d MENU button does not function while the projector is operating the “Auto Sync” or “FREEZE”
functions.
42
Picture Adjustment (“Picture” menu)
Menu operation n Page 41
Q PAGE 1
Q PAGE 2
Picture
Picture
INPUT 1
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
INPUT 1
Picture Mode
Standard
0
0
0
0
0
0
0
CLR Temp
BrilliantColor™
C. M. S.
Progressive
DNR
IRIS
Lamp Setting
Reset
Standard
7500K
1
3D Progressive
Level 1
High Brightness
Bright
1 Selecting the Picture Mode
Selectable
items
The default settings of each item when selecting Picture Mode
Description
CLR Temp
BrilliantColor™
IRIS
Lamp Setting
Standard
For standard image
7500K
0
High Brightness
Bright
Natural
A balanced color image is obtained.
7500K
0
High Brightness
Bright
Dynamic
A vivid image is obtained.
7500K
2
High Brightness
Bright
Movie1
Makes the black levels of the
dark portions of the screen
more pronounced and vivid.
6500K
0
High Brightness
Eco + Quiet
Movie2
Reduces glare and creates a
subdued tone.
6500K
0
Medium Mode
Eco + Quiet
Memory
Allows you to store your picture
adjustment settings. The settings
stored effect each input mode.
7500K
0
High Brightness
Bright
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.
Note • You can also press k PICTURE MODE on the remote control to select the picture mode.
(See page 38.)
2 Adjusting the Image
Adjustment items
O button
Q button
Contrast
For less contrast.
For more contrast.
Bright
For less brightness.
For more brightness.
Color*1
For less color intensity.
For more color intensity.
Tint*1
For making skin tones purplish.
For making skin tones greenish.
Sharp*1
For less sharpness.
For more sharpness.
Red
For weaker red.
For stronger red.
Blue
For weaker blue.
For stronger blue.
BrilliantColor™*2
For making the effect weaker.
For making the effect stronger.
*1 Item that cannot be adjusted in RGB mode.
*2 BrilliantColor™ uses Texas Instruments' BrilliantColor™ technology. As the BrilliantColor™ level is increased,
the image becomes brighter while the color reproduction is kept at a high level.
Note • To reset all adjustment items, select “Reset” and press iENTER. The Picture Mode
settings of the selected input return to the default settings.
43
Picture Adjustment (“Picture” menu) (Continued)
3 Adjusting the Color
Temperature
Selectable
items
5500K
6500K
7500K
8500K
9300K
10500K
Description
For lower color temperature for
warmer, reddish incandescent-like
images.
P
R
For higher color temperature for
cooler, bluish, fluorescent-like images.
Note
• Values on “CLR Temp” are only for general
standard purposes.
4 Adjusting the Colors
Select “C.M.S.” (Color Management System) in
the “Picture” menu and then press i ENTER.
This function adjusts each of the six main colors
that comprise the color wheel, altering their
“Hue”, “Saturation”, or “Value”.
C.M.S.-Value
Sets the brightness of the main colors.
Reset
The adjustments of “Hue”,
“Saturation” and “Value” of all colors
are reset to the default setting.
Adjusting “Hue”, “Saturation”, or “Value”.
1 Press P or R to select either “Hue”, “Saturation”, or
“Value” and then press i ENTER.
2 Select the color to be adjusted with P or R and
adjust it with O or Q.
Example of adjusting the “Hue”
44
5 Progressive
Selectable
items
O button
Closer to magenta
Closer to red
Closer to yellow
Closer to green
Closer to cyan
Closer to blue
Q button
Closer to yellow
Closer to green
Closer to cyan
Closer to blue
Closer to magenta
Closer to red
Description
2D
Useful to display fast-moving images
Progressive such as sports.
3D
Useful to display relatively slowProgressive moving images such as drama and
documentary more clearly.
Film Mode
Sets the hue of the main colors.
C.M.S.-Saturation Sets the saturation of the main colors
Main colors
R (Red)
Y (Yellow)
G (Green)
C (Cyan)
B (Blue)
M (Magenta)
Info
• When the Progressive mode is set to “3D Progressive” or “Film Mode”, the C.M.S. function
cannot be used.
Description
Selectable items
C.M.S.-Hue
Menu operation n Page 41
• When “Saturation” is selected, the selected
color becomes
O: lighter. Q: thicker.
• When “Value” is selected, the selected color
becomes
O: darker. Q: brighter.
• To reset the adjustment values of each color
to the default settings, select “Reset” and press
i ENTER.
Reproduces the image of film source*
clearly. Displays the optimized image of
film transformed with three-two pull down
(NTSC and PAL60Hz) or two-two pull
down (PAL50Hz and SECAM) enhancement to progressive mode images.
* The film source is a digital video recording with the
original encoded as is at 24 frames/second. The
projector can convert this film source to progressive video at 60 frames/second with NTSC and
PAL60Hz or at 50 frames/second with PAL50Hz
and SECAM to play back a high-definition image.
Note
• In NTSC or PAL60Hz, even if the 3D Progressive mode has been set, the three-two pull
down enhancement will be enabled automatically when the film source has been entered.
• When the image is blurred or noisy, switch to
the optimal mode.
• When using progressive inputs, inputs are directly displayed so that 2D Progressive, 3D
Progressive and Film Mode cannot be selected.
Info
• The settings can be made either when INPUT3
or INPUT4 are selected or when INPUT1, 2,
INPUT5, or INPUT6 are selected and the input signal is 480I, 576I, or 1080I.
Menu operation n Page 41
6 Reducing Image Noise
(DNR)
Video digital noise reduction (DNR) provides high
quality images with minimal dot crawl and cross
color noise.
Selectable items
Description
OFF
DNR does not function.
Level 1-3
Sets the DNR level for viewing
a clearer picture.
Note
Set “DNR” to “OFF” in the following cases:
• When the image is blurry.
• When the contours and colors of moving images drag.
• When TV broadcasts with weak signals are
projected.
Info
• This function is available for 480I, 480P, 576I,
and 576P signals using INPUT 1, 2, 5 or 6.
7 Switching the Iris
Setting
This function controls the quantity of the projected light and the contrast of the image.
Selectable items
Description
High Brightness
High brightness is given
priority over high contrast.
Medium Mode
Intermediate mode between
high contrast and high
brightness.
High Contrast
High contrast is given priority
over high brightness.
Note
• You can also use l IRIS on the remote control to change the Iris. (See page 38.)
8 Lamp Setting
Fan
sound
Power
consumption
(When using
AC 100V)
Approx.
87%
Low
310W
Approx.
3,000
hours
100%
Normal
355W
Approx.
2,000
hours
SelectBrightable
ness
items
Eco +
Quiet
Bright
Lamp Life
Note
• When “Lamp Setting” is set to “Eco+Quiet”,
the power consumption will decrease and the
lamp life will extend. (Projection brightness
decreases approximately 13%.)
45
Computer Image Adjustment
(“Fine Sync” menu)
Menu operation n Page 41
Fine Sync
INPUT 5
Clock
Phase
H-Pos
V-Pos
Reset
Special Modes
Auto Sync
0
0
0
0
1080I
On
2 Special Modes Setting
Ordinarily, the type of input signal is detected
and the correct resolution mode is automatically
selected. However, for some signals, the optimal resolution mode in “Special Modes” in the
“Fine Sync” menu may need to be selected to
match the computer display mode.
Cur. sig. freq : H 33.8 kHz / V 60 Hz
1 Adjusting the
Computer Image
Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen.
Selectable items
Description
Clock
Adjusts vertical noise.
Phase
Adjusts horizontal noise (similar
to tracking on your VCR).
H-Pos
Centers the on-screen image by
moving it to the left or right.
V-Pos
Centers the on-screen image by
moving it up or down.
Note
• Avoid displaying computer patterns which
repeat every other line (horizontal stripes).
(Flickering may occur, making the image hard
to see.)
• Information on the currently selected input signal can be confirmed in item 4.
3 Auto Sync (Auto Sync
Adjustment)
Selectable items
Description
On
Auto Sync adjustment will
occur when the projector is
turned on or when the input
signals are switched, when
connected to a computer.
Off
Auto Sync adjustment is not
automatically performed.
Note
• You can automatically adjust the computer
image by setting “Auto Sync” in the “Fine
Sync” menu to “On” or pressing f AUTO
SYNC on the remote control.
• “Clock”, “Phase”, “H-Pos” and “V-Pos” cannot be adjusted when INPUT 6 is selected.
• The adjustable area of each item may be
changed according to the input signal.
• To reset all adjustment items, select “Reset”
and press i ENTER.
Note
• Auto Sync adjustment is also performed by
pressing f AUTO SYNC on the remote control.
• The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual adjustments.
4 Checking the Input
Signal
This function allows you to check the current input signal information.
46
Using the “Options” Menu
Menu operation n Page 41
Options 1
1
2
2
3
4
5
6
7
8
9
0
Image Shift
Overscan H
Overscan V
Subtitle
OSD Display
Video System
Signal Type
HDMI Setting
Background
Auto Power Off
Lamp Timer(Life)
INPUT 1
0
0
0
0
On
Auto
Auto
Standard
Blue
On
0 h
100%
Settings on the Options 1 menu
1 Adjusting the Image
Position
You can move the projected image vertically.
O button
Q button
2 Adjusting the Overscan
This function allows you to adjust the Overscan
area ratio (display area ratio).
Orientation
O button
Q button
Overscan H
(Horizontal)
Reduces the
image.
(The display
area ratio
becomes larger.)
Enlarges the
image.
(The display area
ratio becomes
smaller.)
Overscan V
(Vertical)
Note
• This function can only be adjusted when a
video, S-video, or Component signal is input.
• If the display area ratio is set too large, noise
may appear at the screen edges. If this happens, set the display area ratio to a smaller value.
• The adjustment area changes according to the
input signal when “Resize” is set to “CINEMA
ZOOM”.
• Also read “About Copyrights” on page 37.
3 Adjusting the Vertical Size of
the Display (Subtitle Setting)
With this function, you can adjust the vertical size
of the display to allow for subtitles.
Note
• The Image Shift function cannot be selected
when “Resize” is set to “DOT BY DOT”.
• You can also use the IMAGE SHIFT buttons
on the remote control to adjust the image position.
O button
The image is compressed by adjusting
the vertical size of the display.
Q button
The image is enlarged by adjusting the
vertical size of the display.
Note
• When changing the screen with the Subtitle setting, not only the bottom of the screen rises, but
also the upper part is changed to a certain point.
• The Subtitle setting can be adjusted more effectively with the Overscan and Image Shift
functions.
• The Subtitle setting only works when “Resize”
is set to “CINEMA ZOOM”.
• The adjustment area changes according to the
input signal.
47
Using the “Options” Menu (Continued)
Menu operation n Page 41
4 Setting On-screen Display
Selectable
items
Description
On
All On-screen Displays are displayed.
Off
INPUT/FREEZE/AUTO SYNC/RESIZE/
PICTURE MODE are not displayed.
5 Setting the Video
System
This function can only be set in INPUT 3 or
INPUT 4.
The video input system mode is factory preset
to “Auto”;however, a clear picture from the connected audio-visual equipment may not be received, depending on the video signal difference.
In that case, switch the video signal.
Selectable items
Description
PAL
When connected to PAL video
equipment.
SECAM
When connected to SECAM
video equipment.
NTSC4.43
When reproducing NTSC
signals in PAL video equipment.
NTSC3.58
When connected to NTSC video
equipment.
6 Signal Type Setting
This function allows you to select the input signal type (RGB or Component) for INPUT 5 or
INPUT 6.
Selectable items
Description
Auto
Automatically selects the
appropriate input signal
between RGB and Component.
RGB
Set when RGB signals are
received.
Component
Set when component signals
are received.
Note
• You can also select “Signal Type” using g
RGB/COMP. on the remote control (INPUT 5
or INPUT 6).
7 Selecting the HDMI Setting
When there is an HDMI-capable device connected to INPUT 6, an optimum picture may not
be displayed if the device’s output signal type
and the projector’s input signal type do not match.
If this should occur, switch the HDMI Setting.
Selectable items
Standard
Enhanced
Description
When the black levels of the
image show banding or appear
faded, select the option that
results in the best picture
quality. (In most circumstances,
“Standard” should be selected.)
Note
• The HDMI Setting can be selected only when
INPUT 6 is selected.
8 Selecting the Background
Image
Selectable items
48
Description
Blue
Blue screen
None
— (Black screen)
Menu operation n Page 41
9 Auto Power Off
Function
Selectable
items
Options 2
1
2
3
4
5
6
Description
On
When no input signal is detected for
more than 15 minutes, the projector will
automatically enter standby mode.
Off
The Auto Power Off function will be
disabled.
PRJ Mode
RS-232C
STANDBY Mode
Fan Mode
All reset
Language
INPUT 1
Front
9600 bps
Eco
Normal
English
Settings on the Options 2 menu
Note
• When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
0 Checking the Lamp Life
Status
You can confirm the cumulative lamp usage time
and the remaining lamp life (percentage).
Lamp usage condition
“Life”
Remaining lamp life
100%
5%
Operated exclusively
with Lamp Setting set to
“Eco + Quiet”
Approx.
3,000
hours
Approx.
150 hours
Operated exclusively
with Lamp Setting set to
“Bright”
Approx.
2,000
hours
Approx.
100 hours
1 Reversing/Inverting
Projected Images
Selectable items
Description
Front
Normal image (Projected from
the front of the screen)
Ceiling + Front
Inverted image (Projected
from the front of the screen
with an inverted projector)
Rear
Reversed image (Projected
from the rear of the screen or
with a mirror)
Ceiling + Rear
Reversed and inverted image
(Projected with a mirror)
See page 19 for details of Projection (PRJ) Mode.
Note
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the usage condition.
49
Using the “Options” Menu (Continued)
Menu operation n Page 41
2
2 Selecting
Selecting the
theTransmission
Transmission
Speed
(RS-232C)
Speed (RS-232C)
Make sure that both the projector and computer
are set for the same baud rate.
Selectable
items
9600bps
Description
P
R
3 Reducing the Power
Consumption When the
Power Is in Standby Mode
When “STANDBY Mode” has been set to “Standard”, the RS-232C function is activated and
power is consumed even in standby mode. It is
recommended that “STANDBY Mode” be set to
“Eco” when it is not being used. This reduces
power consumption when the projector is in
standby mode.
Selectable items
Eco
Description
The RS-232C function is
activated even if the projector is
in standby mode.
The RS-232C function is
switched off when the projector
is in standby mode.
Note
• When you want to control the projector using
the RS-232C function, set to “Standard”.
50
This function changes the fan rotation speed.
Selectable
items
Description
Normal
Suitable for normal environments.
High
Select this when using the projector at
altitudes of approximately 4,900 feet
(1,500 meters) or more.
Transmission speed is slow.
115200bps Transmission speed is rapid.
Standard
4 Fan Mode Setting
When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.
5 Returning to the Default
Settings
Use “All reset” to initialize all the adjustments you
have made to the default settings.
Note
The following items cannot be initialized.
• “Fine Sync” menu
– Special Modes
• “Options1” menu
– Lamp Timer (Life)
– Language
6 Selecting the On-screen
Display Language
The projector can switch the on-screen display
language among 11 languages.
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Maintenance
Cleaning the projector
■ Ensure that you have unplugged the power
cord before cleaning the projector.
■ The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or
thinner, as these can damage the finish on the
cabinet.
■ Do not use volatile agents such as insecticides
on the projector.
Do not attach rubber or plastic items to the
projector for long periods.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the
projector.
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in
a mild detergent diluted with water, wring the
cloth well and then wipe the projector.
Strong cleaning detergents may discolor, warp
or damage the coating on the projector. Make
sure to test on a small, inconspicuous area on
the projector before use.
Cleaning the lens
■ Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the
coating film on the surface of the lens.
■ As the surface of the lens can easily get
damaged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Mil
dd
ete
rge
nt
Mild detergent diluted
with water
Wax
Thinner
Info
• If you want to clean the air vents during projector operation, be sure to press o
STANDBY-ON on the projector or aSTANDBY
on the remote control and put the projector
into standby mode. After the cooling fan has
stopped, clean the vents.
51
Maintenance Indicators
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the
projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter standby mode. After the projector has entered standby mode,
follow the procedures given below.
Top View
Temperature warning indicator
Lamp indicator
Power indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
“
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp
will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projector will enter standby mode. After “
” appears, be sure to perform the measures described on page
53.
About the lamp indicator
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be
displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will
automatically turn off and then the projector will automatically enter standby mode. At this time, the
lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will
not turn on.
Indicators on the Projector
Power indicator
Lamp indicator
Temperature warning
indicator
52
Green on
Normal (Standby)
Red on
Normal (Power on)
Green blinks
Abnormal (See page 53.)
Red blinks
Green on
Normal (Cooling)
Normal
Green blinks
The lamp is warming up or shutting down.
Red on
The lamp is shut down abnormally or
requires to be changed. (See page 53.)
Off
Normal
Red on
The internal temperature is abnormally
high. (See page 53.)
Maintenance indicator
Temperature
warning
indicator
Lamp
indicator
Power
indicator
Normal
Abnormal
Off
Red on
(Standby)
Problem
The internal
temperature is
abnormally
high.
Cause
• Blocked air intake
• Relocate the projector to
an area with proper
ventilation. (see page 8)
• Cooling fan
breakdown
• Internal circuit
failure
• Clogged air intake
• Take the projector to your
nearest EIKI Authorized
Dealer or Service Center
for repair.
The lamp does
not illuminate.
• The lamp is shut
down abnormally.
• Disconnect the power cord
from the AC outlet, and
then connect it again.
Time to change
the lamp.
• Remaining lamp life
becomes 5% or
less.
• Carefully replace the lamp.
(See page 55.)
• Take the projector to your
nearest EIKI Authorized
Dealer or Service Center
for repair.
• Please exercise care when
replacing the lamp.
• Securely install the cover.
Green on
(Green
blinks
when the
lamp is
warming
up or
turning
off.)
Red on
(Standby)
The lamp does
not illuminate.
• Burnt-out lamp
• Lamp circuit failure
Green on/
Red on
Green
blinks
The power
indicator blinks
in green when
the projector is
on.
• The lamp unit cover
is open.
Red
blinks
(Cooling)
Red on
Possible Solution
• If the power indicator blinks
in green even when the
lamp unit cover is securely
installed, contact your
nearest EIKI Authorized
Dealer or Service Center
for advice.
Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,
replace the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan
speed may change and this is not a malfunction.
• Do not unplug the power cord after the projector has entered standby mode and while the cooling
fan is running. The cooling fan runs for about 90 seconds.
53
Regarding the Lamp
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
(percentage) can be checked with the on-screen display. (see page 49)
■ Purchase a replacement lamp of type AH-11201 from your place of purchase, nearest EIKI Authorized
Dealer or Service Center.
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest EIKI Authorized Dealer or
Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case
of exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burn or injury.
■ Carefully change the lamp by following the instructions described in this section. * If you wish,
you may have the lamp replaced at your nearest EIKI Authorized Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest EIKI Authorized
Dealer or Service Center for repair.
54
Removing and Installing the
Lamp Unit
Warning!
• The lamp unit becomes very hot while the projector is operating. Do not remove the lamp
unit from the projector right after use. The lamp
and parts around the lamp will be very hot and
may cause burns or injury.
Optional
accessory
Lamp unit
AH-11201
Info
• Make sure that you remove the lamp unit by
the handle. Do not touch the glass surface of
the lamp unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, be sure to carefully follow the steps
below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
1
Press oSTANDBY-ON on the projector or aSTANDBY on the remote control to put the projector
into standby mode.
STANDBY-ON button
AC socket
• Wait until the cooling fan stops.
2
Disconnect the power cord.
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
1
3
Remove the lamp unit cover.
• Turn the projector over. Loosen the user
service screw (1) that secures the lamp
unit cover. Remove the lamp unit cover
(2).
2
User service screw
(for lamp unit cover)
55
Regarding the Lamp (Continued)
4
Remove the lamp unit.
5
Insert the new lamp unit.
6
Handle
• Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow. At this time, keep the lamp unit
horizontal and do not tilt it.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
Securing screws
Replace the lamp unit cover.
• Align the tab on the lamp unit cover (1)
and place it while pressing the tab (2)
to close it. Then tighten the user service
screw to secure the lamp unit cover.
2
Info
• If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is connected to the projector.
1
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or explode.
1
2
56
AC socket
STANDBY-ON
button
Connect the power cord.
• Plug the power cord into the AC socket
of the projector.
ENTER button
Reset the lamp timer.
MENU button
• While simultaneously holding down
rMENU, pENTER and R on the projector, press oSTANDBY-ON on the projector.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
R button
Connecting Pin Assignments
COMPUTER-RGB/COMPONENT INPUT5 Terminal: 15-pin Mini D-sub female connector
11
15
1
6
5
10
COMPUTER-RGB Input
1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Not connected
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. Not connected
12. Bi-directional data
13. Horizontal sync signal: TTL level
14. Vertical sync signal: TTL level
15. Data clock
Component Input
1. PR (CR)
2. Y
3. PB (CB)
4. Not connected
5. Not connected
6. Earth (PR)
7. Earth (Y)
8. Earth (PB)
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
RS-232C Terminal: 9-pin Mini DIN female connector
8
Pin No. Signal
I/O
Reference
Name
1.
Not connected
9
7
2.
RD
Connected to internal circuit
Receive Data
Input
3.
SD
Connected to internal circuit
Send Data
Output
4.
Not connected
6
3 5.
SG
Connected to internal circuit
Signal Ground
6.
Not connected
7.
RS
Connected to CS in internal circuit
Request to Send
4
5
8.
CS
Connected to RS in internal circuit
Clear to Send
9.
Not connected
2
1
RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor
1
6
5
9
Pin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Signal
Name
I/O
RD
SD
Receive Data
Send Data
SG
Signal Ground
RS
CS
Request to Send
Clear to Send
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
Input
Output
RS-232C Cable recommended connection: 9-pin D-sub female connector
5
9
1
6
Pin No. Signal
CD
1.
RD
2.
SD
3.
ER
4.
SG
5.
DR
6.
RS
7.
CS
8.
CI
9.
Pin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Signal
CD
RD
SD
ER
SG
DR
RS
CS
CI
Note
• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
Projector
Pin No.
4
5
6
Computer
Pin No.
4
5
6
57
Connecting Pin Assignments (Continued)
Pin No.
1.
2.
3.
4.
5.
6.
7.
HDMI Terminal
1
19
2
18
Name
TMDS Data2+
TMDS Data2 Shield
TMDS Data2TMDS Data1+
TMDS Data1 Shield
TMDS Data1TMDS Data0+
Pin No.
8.
9.
10.
11.
12.
13.
Name
TMDS Data0 Shield
TMDS Data0TMDS Clock+
TMDS Clock Shield
TMDS ClockCEC
Pin No.
14.
15.
16.
17.
18.
19.
Name
Reserved
SCL
SDA
DDC/CEC Ground
+5V Power
Hot Plug Detect
RS-232C Specifications and Command Settings
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable
(cross type, sold separately) to the projector. (See page 27 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Parity bit: None
Baud rate: * 9,600 bps/115,200 bps
Stop bit: 1 bit
Data length: 8 bits
Flow control: None
* Set the projector's baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code.
After the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1
C2
C3 C4
P1
P2
Command 4-digit
Response
code format
P3
P4
Return code (0DH)
Parameter 4-digit
Problem response
(communication error or incorrect command)
Normal response
O
K
Return code (0DH)
E
R
R
Return code (0DH)
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30
seconds after the power has been turned on, and then transmit the commands.
• When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
Commands
Example: When turning on the
projector, make the
following setting.
CONTROL CONTENTS
Power Off
Power On
INPUT 1 (Video1 : Component1)
INPUT 2 (Video2 : Component2)
INPUT 3 (Video3 : S-Video)
INPUT 4 (Video4 : Video)
INPUT 5 (RGB1 : RGB/Component)
INPUT 6 (RGB2 : RGB/Component)
58
COMMAND
P O W R
P O W R
I V E D
I V E D
I V E D
I V E D
I R G B
I R G B
Computer
P
PARAMETER
_ _ _ 0
_ _ _ 1
_ _ _ 1
_ _ _ 2
_ _ _ 3
_ _ _ 4
_ _ _ 1
_ _ _ 2
O W
RETURN
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
R
_
_
_
1
→
←
Projector
O
K
Note
• If an underbar (_) appears in the parameter
column, enter a space.
Computer Compatibility Chart
Computer
• Multiple signal support
• Compatible with sync on green signal
Horizontal Frequency: 15-70 kHz,
• Expansion System resizing technology
Vertical Frequency: 45-85 Hz,
Pixel Clock: 12-85 MHz
Sync signal: Compatible with TTL level
The following is a list of modes that conform to VESA. However, this projector supports other
signals that are not VESA standards.
Resolution
PC/MAC
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.4
35.1
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
45.0
47.8
34.9
37.8
49.7
60.2
60
70
85
60
70
85
60
70
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
60
60
67
60
75
75
640 × 350
640 × 400
720 × 350
VGA
720 × 400
640 × 480
PC
SVGA
800 × 600
XGA
1,024 × 768
—
MAC 13"
VGA
MAC 16"
SVGA
MAC 19"
XGA
1,280 × 720
1,280 × 768
640 × 480
800 × 600
832 × 624
1,024 × 768
VESA
Standard
HDMI
Support
Display
✔
✔
✔
✔
✔
Upscale
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
True
Upscale
True
Note
• When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.
DTV
Signal
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
480I
15.7
60
480P
31.5
60
540P
33.8
60
HDMI Support
✓
576I
15.6
50
576P
31.3
50
✓
720P
45.0
60
✓
1035I
28.1
50
1035I
33.8
60
1080I
28.1
50
✓
1080I
33.8
60
✓
59
Troubleshooting
Problem
Picure does not appear
or projector does not
start.
Check
Page
• Projector power cord is not plugged into the wall outlet.
28
• Power to the external connected devices is off.
–
• The selected input mode is wrong.
29
• Cables incorrectly connected to the projector.
23–27
• Remote control battery has run out.
14
• External output has not been set when connecting notebook
computer.
26
• The lamp unit cover is not installed correctly.
55, 56
• Cables incorrectly connected to the projector.
23–27
• “Bright” is set to minimum position.
43
• Depending on the computer you are using, an image may not be
projected unless the signal output setting of the computer is
switched to the external output. Refer to the owner’s manual of the
computer for how to switch its signal output settings.
–
• Image adjustments are incorrectly set.
• Make adjustments to “Color”, “Tint” and “BrilliantColor™” in “Picture
Mode”.
43
No picture appears (or
picture is dark).
(Video Input only)
• Video input system is incorrectly set.
48
Color is faded or poor.
Picture is blurred;
noise appears.
• Adjust the focus.
30
• The projection distance exceeds the focus range.
20
• There is fog on the lens. If the projector is carried from a cold room
into a warm room, or if it is suddenly heated, condensation may form
on the surface of the lens and the image will become blurred. Please
set up the projector at least one hour before it is to be used. If
condensation should form, remove the power cord from the wall
outlet and wait for it to clear.
–
(Computer Input only)
Picture is green on
INPUT 5 (Component)/
INPUT 6 (Component).
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)
46
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)
46
• Noise may appear depending on the computer.
–
• Select “Signal Type” in the “Options1” menu and change the input
signal type.
Picture is pink (no green)
on INPUT 5 (RGB)/INPUT
6 (RGB).
An unusual sound is
• If the picture is normal, the sound is due to cabinet shrinkage
occasionally heard from
caused by room temperature changes. This will not affect operation
the cabinet.
or performance.
Maintenance indicator on • See “Maintenance Indicators”.
the projector illuminates.
60
48
–
52
Problem
Check
Page
Picture is too bright and
whitish.
• Image adjustments are incorrectly set.
43
The black levels of the
image show banding or
appear faded when
INPUT 6 is selected.
• Select the HDMI Setting (“Standard” or “Enhanced”) that results in
the best picture quality.
48
The cooling fan becomes • When temperature inside the projector increases, the cooling fan
noisy.
runs faster.
The lamp does not light
up even after the
projector turns on.
–
• The lamp indicator is illuminating in red.
Replace the lamp.
52, 55
The image sometimes
flickers.
• Cables incorrectly connected to the projector or the connected
equipment works improperly.
• If this happens frequently, replace the lamp.
23-27
The lamp needs much
time to turn on.
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
55
The lamp suddenly turns
off during projection.
Picture is dark.
The remote control
cannot be used.
55
• Operate the remote control while pointing it at the projector’s remote
control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent light is shining on the
projector’s remote control sensor, place the projector where it will not
be affected by strong light.
15
• The batteries may be depleted or inserted incorrectly. Make sure the
batteries are inserted correctly or insert new ones.
14
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation
or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
61
Specifications
Product type Projector
Model EIP-1600T
Video system NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/
DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50
Display method Single Chip Digital Micromirror DeviceTM (DMDTM) by Texas Instruments
DMD panel Panel size: 0.65", 1chip DMD
Drive method: Digital Light Processing (DLP™)
No. of dots: 983,040 dots (1280 [H] × 768 [V])
Lens 1–1.15 × zoom lens, F2.4–2.6, f = 19.0–21.9 mm
Projection lamp 275 W DC lamp
Component input signal RCA connector
(INPUT1/2) Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB (CB): 0.7 Vp-p, 75 Ω terminated
PR (CR): 0.7 Vp-p, 75 Ω terminated
S-video input signal 4-pin mini DIN connector
(INPUT 3) Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Video input signal RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω
(INPUT 4) terminated
Computer RGB/ 15-pin mini D-sub connector
Component input signal RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated
(INPUT 5) HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
HDMI input signal HDMI terminal (video signal only)
(INPUT 6)
Horizontal resolution 720 TV lines (DTV720P)
Vertical frequency 45–85 Hz
Horizontal frequency 15–70 kHz
Pixel clock 12–85 MHz
RS-232C terminal 9-pin mini DIN connector
TRIGGER terminal Power jack: DC 12V output
Rated voltage AC 100–240 V
Input current 3.7 A
Rated frequency 50/60 Hz
Power consumption 355 W (Lamp Setting “Bright”)/
310 W (Lamp Setting “Eco + Quiet”) with AC 100 V
340 W (Lamp Setting “Bright”)/
300 W (Lamp Setting “Eco + Quiet”) with AC 240 V
Power consumption (standby) 4 W (AC 100 V) – 5 W (AC 240 V)*1
Heat dissipation 1,335 BTU/hour (Lamp Setting “Bright”)/
1,165 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 100 V
1,280 BTU/hour (Lamp Setting “Bright”)/
1,130 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 240 V
Operating temperature 41°F to 95°F (+5°C to +35°C)
Storage temperature –4°F to 140°F (–20°C to +60°C)
Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 12 13/32" × 4 19/64" × 11 1/32" (315 (W) × 109 (H) × 280 (D) mm) (main body only)
12 13/32" × 4 47/64" × 11 37/64" (315 (W) × 120 (H) × 294 (D) mm) (including adjustment foot and projecting parts)
Weight (approx.) 8.8 lbs. (4.0 kg)
Replacement parts Remote control, Power cord for U.S. and Canada, etc., Power cord for Europe,
except U.K., Video cable, DIN-D-sub RS-232C adaptor, Quick Guide, Owner’s
manual
*1 When STANDBY Mode is set to “Eco”
As a part of policy of continuous improvement, EIKI reserves the right to make design and
specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
62
Dimensions
11
73
105
109
47
9
280
5
Units: inches (mm)
77.5
80
315
M4
M4
47.5
104
M4
11
M4
33.8
75
46.2
65.5
63
Index
AC socket ....................................................... 28
Accessories ................................................... 10
Adjustment buttons ........................................ 41
Aspect ratio .................................................... 36
Auto Power Off ............................................... 49
Auto Sync
(Auto Sync adjustment) .............................. 46
AUTO SYNC button ....................................... 46
Background .................................................... 48
Backlight button ............................................. 13
Blue ................................................................ 43
Bright ............................................................. 43
BrilliantColor™ ............................................... 43
Checking the Input Signal ............................. 46
CINEMA ZOOM ...................................... 36, 37
Clock .............................................................. 46
CLR Temp (Color Temperature) .................... 44
C.M.S. ............................................................ 44
Color .............................................................. 43
Contrast ......................................................... 43
DOT BY DOT ................................................. 37
DNR ............................................................... 45
ENTER button ................................................ 41
Exhaust vent ........................................... 12, 51
Fan Mode ....................................................... 50
Fine Sync ....................................................... 46
Focus ring ...................................................... 30
FREEZE button ............................................. 38
GEOMETRIC ADJUSTMENT ....................... 34
H & V KEYSTONE ......................................... 35
HDMI Setting ................................................. 48
H-Pos ............................................................. 46
HEIGHT ADJUST lever ................................. 30
Hue ................................................................ 44
Image Shift .................................................... 47
IMAGE SHIFT buttons ................................... 38
INPUT 1 terminal ........................................... 23
INPUT 1 – 6 modes ....................................... 29
INPUT 2 terminal ........................................... 23
INPUT 3 terminal ........................................... 24
INPUT 4 terminal ........................................... 24
INPUT 5 terminal .................................... 25, 26
INPUT 6 terminal ........................................... 25
INPUT buttons ............................................... 29
Intake vent ........................................ 11, 12, 51
IRIS button ..................................................... 38
Kensington Security
Standard connector ............................. 12, 13
KEYSTONE button ........................................ 32
Keystone Correction ...................................... 32
64
Lamp ....................................................... 10, 54
Lamp indicator ............................................... 52
Lamp Setting ................................................. 45
Lamp Timer (Life) .......................................... 49
Lamp unit ....................................................... 55
Language (on-screen display language) ...... 50
Lens cap ........................................................ 11
MENU button ................................................ 41
ON button ...................................................... 28
Optional accessories ..................................... 10
OSD Display .................................................. 48
Overscan ....................................................... 47
Phase ............................................................. 46
Picture Adjustment ........................................ 43
Picture Mode .......................................... 38, 43
PICTURE MODE button ................................ 38
Picture (Screen) Size and Projection Distance ....... 20
Power cord ..................................................... 28
PRJ Mode ............................................... 19, 49
Progressive .................................................... 44
R-03 batteries ................................................ 14
Rear adjustment foot ..................................... 31
Red ................................................................ 43
Remote control .............................................. 13
Remote control sensor .................................. 15
Replacing the lamp ................................. 54, 55
Resize ..................................................... 36, 37
RESIZE button ............................................... 36
RETURN button ............................................. 41
RGB/COMP. button ........................................ 48
RS-232C Setting ............................................ 50
RS-232C terminal .......................................... 27
Saturation ...................................................... 44
Sharp ............................................................. 43
SIDE BAR ............................................... 36, 37
Special Modes ............................................... 46
STANDBY button ........................................... 29
STANDBY-ON button .............................. 28, 29
STANDBY Mode ............................................ 50
STRETCH ............................................... 36, 37
Subtitle ........................................................... 47
Supplied accessories .................................... 10
Temperature warning indicator ...................... 52
Tint ................................................................. 43
TRIGGER terminal ........................................ 12
Value .............................................................. 44
Video System ................................................ 48
V-Pos .............................................................. 46
Zoom ring ....................................................... 30
A-Key to better communications
U.S.A.
Canada
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-242-3454 (949)-457-0200
Fax : 800-457-3454 (949)-457-7878
E-Mail : usa@eiki.com
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel : 800-563-3454 (705)-527-4084
Fax : 800-567-4069 (705)-527-4087
E-Mail : canada@eiki.com
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12
65510 Idstein
Deutschland
Tel : 06126-9371-0
Fax : 06126-9371-14
E-Mail : info@eiki.de
Eastern Europe
EIKI CZECH spol. s.r.o.
Umelecká 15
170 00 Praha 7
Czech Republic
Tel : +42 02 20570024
+42 02 20571413
Fax : +42 02 20571411
E-Mail : easterneurope@eiki.de
Japan & Worldwide
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka,
530-0028 Japan
Tel : +81-6-6311-9479
Fax : +81-6-6311-8486
WorldWide Website http://www.eiki.com
Printed in China
TINS-C312WJZZ
06P03-CH-NG