Emerson CF980MAB 00 EMX Owner`s manual

READ AND SAVE THESE INSTRUCTIONS
TUREEN™
Damp Location
Ceiling Fan
Owner's Manual
Net Weight:
35.8
Model No.
CF980MAB 00
CF980MBX 00
EMX
Lbs.
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for a lifetime of your ceiling fan. All other components and accessories are
covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of the
motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson Electric Co. will refund the actual purchase
price of your fan. We will ship the repaired product or replacement to you at no charge, but you are responsible for all costs or removal, reinstallation and
shipping of the product to Emerson Electric Co.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF
OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of Emerson
Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Air Comfort
Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any defects, malfunctions or failures
caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and no employee,
agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT RESPONSIBLE
FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages
as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if
this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
FOR CANADA, THIS FAN MUST BE SECURED DIRECTLY TO THE BUILDING STRUCTURE/CEILING JOIST.
DO NOT SECURE THIS FAN TO AN OUTLET BOX.
Part No. F40BP73530000
Form No. BP7353
U.L. Model No.: CF980
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and Local
Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must
be grounded as a precaution against possible electrical shock. Electrical installation should be
made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50
pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support of 50 lbs. or less”, and use
the mounting screws provided with the outlet box. Most outlet boxes commonly used for support of
light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The downrod furnished with the fan proves the minimum recommended floor-to-fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with th fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not
know enough about electrical wiring, have your fan installed by a licensed electrician.
CAUTION: The halogen bulb operates at high internal pressure and high surface temperatures and
could shatter unexpectedly. The halogen bulb generates UV (ultraviolet) radiation that may cause skin
and eye irritation with prolonged exposure. To avoid risks of burns or other injury, assure power is off
before attempting to install or replace halogen bulb. Do not operate fan/light without lower glass in
place.
7. This fan uses a halogen bulb. Do not touch the bulb with bare hands. Fingerprints may result in
shorter bulb life. Remove fingerprints with alcohol.
8. Use only with light kits marked Suitable For Use in Damp Locations.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electrical shock, this fan should only be used with fan speed
control, Model No. SW105, manufactured by Rhine Electric Co., Ltd.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use this product by Emerson Electric Co. Substitution of parts
or accessories not designated for use with this product by Emerson could result in personal injury or
property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
WARNING: To reduce the risk of electrical shock, this fan must be installed with a general use,
isolating control/switch.
THIS FAN IS SUITABLE FOR DAMP LOCATIONS SUCH AS
COVERED PORCHES, COVERED PATIOS, AND COVERED DECKS. . .
ANYWHERE THERE IS A ROOF OVERHEAD.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
Installed Wire Length
Up to 50 ft.
50-100 ft.
One Phillips head screwdriver
One stepladder
MATERIALS
!
Wiring, outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the following
sizes:
Wire Size A.W.G.
14
12
WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 8). If you feel
you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is
completed, place a check mark in the box. This will insure that all steps have been
completed and will be helpful in finding your place should you be interrupted.
!
NOTE: Place the parts from the loose parts bags in a
small container to keep them from being lost. If any
parts are missing, contact your local retailer or
catalog outlet for replacement before proceeding.
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
a.
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
b.
n.
h.
c.
1. Open styrofoam unit containing fan. Remove top
half of styrofoam unit. Remove parts and check to
see that you have received the following parts:
NOTE: If you are uncertain of part description,
refer to exploded view illustration.
One ceiling cover
One hanger bracket
One hanger ball/downrod assembly
One coupling cover
Fan motor and housing assembly
Four blade flanges
Four fan blades
One light kit assembly
Three 50-watt, MR-16, GU-10 halogen bulbs
One light kit glass
One SW114 wall control/3 wall control covers
One loose parts bag containing:
1. Thirteen #10-24 x 1/4” oval head blade screws
2. Nine 1/4-20 x 1/2” oval head flange screws
3. Two 1-1/4” threaded studs
4. Two knurled knobs
5. Two lockwashers
7. One hairpin clip
8. One clevis pin
9. Four #10-24 x 1” lower housing screws
10. Four #10-24 x 5/16” pan head screws
m. One SW105 receiver
n. One lower housing
i.
d.
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
k.
l.
j.
e.
m.
HIHI
LIGHT
MED
MED
LOW
LOW
REV
REV
FAN OFF
f.
k.
l.
g.
3
Electrical Requirements
LOWER HOUSING
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
!
WARNING
FAN HOUSING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 50 lbs. or less”, and use screws
supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
Figure 1
!
WARNING
3. Install the lower housing onto the fan motor by
orientating the three protruding keys into the slots
on the lower housing to secure. Fasten the lower
housing onto the fan motor using the three
#10-24 x 1” lower housing screws (Figure 2).
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
#10-24 x 1" LOWER
HOUSING SCREW (3)
LOWER
HOUSING
Ceiling Fan Procedures
General
Your Emerson Ceiling Fan/Light Wall Control consists
of a wall mount transmitter. The SW114 transmitter
works in conjunction with the SW105 Receiver
(purchased separately). The receiver is mounted
under the fan ceiling cover. The wall control is
designed to separately control your ceiling fan speed,
direction, uplight and downlight intensity, page 11.
Code switches in the wall control and receiver may be
set in 16 different positions. If your fan and light go on
and off without using your control, you may be getting
interference from other transmitters such as garage
door openers, car alarms or security systems.
To remedy this situation, simply change the combination code in your wall control and receiver.
PROTRUDING KEY (3)
FAN MOTOR
Figure 2
4. Connect the fan motor blue wire to the blue wire
from the light kit assembly; connect the fan motor
white wire to the white wire from the light kit
assembly (Figure 3).
1. Remove the fan motor and housing assembly from
the styrofoam packaging and position it so that the
bottom of the motor is facing you.
2. Position the bottom styrofoam section on a flat
surface exposing the large center hole for fan
motor placement. Place the fan motor housing into
the hole so that the bottom of the motor is facing
up. Position the lower housing over the fan motor
(Figure 1). The styrofoam section will hold the
assembly while you perform the following steps.
LIGHT KIT
WHITE WIRE
FAN MOTOR
WHITE WIRE
LIGHT KIT
BLUE WIRE
FAN MOTOR
BLUE WIRE
LIGHT KIT
ASSEMBLY
Figure 3
4
CAUTION: Before installing and tightening the
screws, be sure there are no wires pinched
between the bottom of the light kit assembly and
fan motor.
MOTOR
COUPLING
SETSCREW (2)
HAIRPIN
CLIP
CLEVIS PIN
5. Install the three #10-24 x 5/16” pan head screws to
secure the light kit assembly to the lower housing
(Figure 4).
DOWNROD
HAIRPIN CLIP
#10-24 x 5/16" PAN HEAD
SCREW (3)
MOTOR
COUPLING
LIGHT KIT
ASSEMBLY
CLEVIS PIN
SETSCREW (2)
Figure 6
!
LOWER
HOUSING
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew is securely
tightened. Failure to verify that the pin and setscrew
are properly installed (as shown in Figure 2) could
result in the fan falling.
Figure 4
6. Carefully turn the partially assembled fan motor
housing onto the styrofoam section. The styrofoam
section will hold the assembly while you perform
the following steps.
10. Install the two setscrew (supplied) in the motor
coupling (Figure 6). While pulling up on the
downrod, tighten the setscrews using the
setscrew wrench (supplied).
NOTE: The setscrews must be properly installed
as described above, or fan wobble could result.
11. Mount the blade flanges to fan blades using three
#10-24 x 1/4” oval head blade screws per blade
(supplied) (Figure 7). Repeat for all blade/flange
assemblies.
NOTE: Be sure to position the flange onto the
blade with the ribs side up.
7. Remove the hanger ball from the downrod by
loosening the setscrew in the hanger ball until the
ball falls freely down the downrod (Figure 5).
Remove the pin from the downrod, then remove
the hanger ball. Retain the pin and hanger ball for
reinstallation in Step 15.
PIN
HANGER
BALL
DOWNROD
WARNING
SETSCREW
!
WARNING
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
Figure 5
8. Separate, untwist and unkink the three motor leads.
Route the motor leads through the downrod and
seat the downrod in the motor coupling (Figure 6).
#10-24 x 1/4" OVAL
HEAD BLADE SCREW
(3 PER BLADE)
9. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip (Figure 6). (Pin
and clip are supplied in loose parts bag.) The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Push the
straight leg of the hairpin clip through the hole near
the end of the clevis pin until the curved portion of
the hairpin clip snaps around the clevis pin. The
hairpin clip must be properly installed to prevent
the clevis pin from working loose. Pull the downrod
to make sure the clevis pin is properly installed.
FLANGE
BLADE
Figure 7
NOTE: Take care not to scratch fan housing when
installing blades.
5
12. Position one of the blade assemblies onto the
motor hub and secure blade assembly using two
1/4-20 x 1/2” oval head flange screws (provided).
Repeat for all blade assemblies (Figure 8).
!
WARNING
It is critical that the pin in the hanger ball is properly
installed and the setscrews securely tightened.
Failure to verify that the pin and setscrews are
properly installed could result in the fan falling.
15. Reinstall the hanger ball on the downrod (Figure
10) as follows. Route the motor leads through the
hanger ball and slide the hanger ball over the
downrod. Install the pin through the holes at the
top of the downrod and slide the hanger ball up
the downrod, aligning the ball so the pin in captured in the groove in the top of the hanger ball.
Pull the hanger ball up tight against the pin and
securely tighten the setscrew in the hanger ball. A
loose setscrew could create fan wobble.
16. The fan comes with blue, black and white leads
that are 80-inches long. Before installing the fan,
measure up approximately 6 to 9-inches above top
of hanger ball/downrod assembly. Cut off excess
leads and strip back insulation 1/2-inch from end
of leads.
1/4-20 x 1/2" OVAL HEAD
FLANGE SCREW (2 PER
FLANGE)
BLADE
ASSEMBLY
PIN
Figure 8
HANGER BALL
13. Slide the coupler cover over the downrod
and position it to cover the motor coupling
(Figure 9).
14. Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 9).
DOWNROD
DOWNROD
SETSCREW
CEILING
COVER
Figure 10
17. You have now completed the assembly of your
new ceiling fan. You can now proceed with hanging and wiring your fan.
COUPLING COVER
Figure 9
6
How to Hang Your Ceiling Fan
!
2. Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was just
attached to the outlet box (Figure 13). Be sure the
groove in the ball is lined up with the tab on the
hanger bracket (Figure 12).
WARNING
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 11).
CEILING
!
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
AT LEAST
7'
Figure 11
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
FLOOR
!
WARNING
HANGER
BRACKET
The outlet box and joist must be securely mounted
and capable of supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable for Fan Support
of 50 lbs. or less”.
!
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
OUTLET
BOX
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
HANGER BALL/
DOWNROD
ASSEMBLY
Figure 13
1. Securely attach the hanger bracket to the outlet
box using the two screws supplied with the outlet
box. (Figure 12.)
!
OUTLET
BOX
HANGER
BRACKET
TAB
Figure 12
7
How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
!
3. Using wire connectors (supplied), make wiring connections as follows (Figure 14 and 15):
a. Connect the white fan wire and the white supply
wire to the white receiver wire (AC IN/
MOTOR N).
b. Connect the black fan wire to the black receiver
wire (TO MOTOR L).
c. Connect the black supply wire to the black/white
receiver wire (AC IN L).
d. Cut off the ends of the blue and yellow receiver
wires and strip back insulation 1/2-inch from the
ends of the wires.
e. Connect the blue fan wire to the blue receiver
wire (BOTTOM LIGHT).
f. Connect the green ground wires from the hanger bracket and the hanger ball to the supply
ground wire (bare or green).
NOTE: Do not use capped yellow wire.
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box
before wiring. All wiring must be in accordance with
National and Local codes and the ceiling fan must be
properly grounded as a precaution against possible
electrical shock.
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan and light kit or receiver.
1. Pull the wire leads, coming from the end of the
downrod, and the supply wires through the open
side of the hanger bracket. (Figure 14).
2. Position the SW105 Receiver (supplied) in the ceiling cover so that the flat side of the receiver faces
up and the open portion of the receiver is to the
right, as shown in Figure 14.
OUTLET BOX
BLACK SUPPLY WIRE
BLACK FAN WIRE
HANGER BRACKET
HANGER BRACKET
GROUND WIRE
(GREEN)
BLACK/WHITE RECEIVER WIRE
BLUE FAN WIRE
HANGER BALL
GROUND WIRE
(GREEN)
BLUE RECEIVER
WIRE
OPEN PORTION
OF RECEIVER
HERE
SUPPLY
GROUND
WIRE (GREEN
OR BARE)
YELLOW RECEIVER WIRE
DO NOT USE
RECEIVER
BLACK RECEIVER WIRE
WHITE RECEIVER WIRE
WHITE SUPPLY
WIRE
CEILING COVER
WHITE FAN WIRE
WIRE CONNECTOR
Figure 14
8
SW105
RECEIVER
BLACK
SUPPLY
TO
110V
SUPPLY
WHITE RECEIVER WIRE
BLACK RECEIVER WIRE
BLACK/WHITE RECEIVER
WHITE SUPPLY WIRE
WHITE FAN WIRE
BLUE RECEIVER WIRE
BLUE FAN WIRE
BLACK FAN WIRE
YELLOW RECEIVER
WIRE
DO NOT USE
DOWNROD
Figure 15
!
7. Secure the ceiling cover in place by sliding
lockwashers (supplied) over the threaded studs and
installing the two knurled knobs (supplied).
(Figure 17.) Tighten the knurled knobs securely until
the ceiling cover fits snugly against the ceiling and the
hole in the ceiling cover is clear of the downrod. Your
fan is now wired to be turned on and off from the fan
switch.
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
4. Carefully turn the wires upward and insert them up
through the open side of the hanger bracket and
into the outlet box. Push the green and white wires
into one side of the outlet box; push the black, blue
and yellow wires into the other side of the outlet
box.
1-1/4"
THREADED
STUD
CEILING
COVER
LOCKWASHER
OUTLET BOX
KNURLED KNOB
Figure 17
HANGER
BRACKET
!
RECEIVER
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
CEILING
COVER
Figure 16
5. Screw the two 1-1/4” threaded studs (supplied)
into the tapped holes in the hanger bracket
(Figure 17).
6. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 17).
9
Halogen Bulb and Glass Installation
2. Place the glass onto the light kit assembly aligning
the three flat areas on the top flange of the glass
with the three pins on the inside of the assembly
(Figure 19). Then turn the glass clockwise until it
stops turning.
1. Do not touch the new 50-watt (maximum) MR-16,
GU-10 bulb with your bare fingers; using a cloth or
soft gloves to hold the bulb, gently push it into the
socket and twist to lock the lamp into the socket
(Figure 18). If there is any doubt that the bulb may
have been contaminated by your touch, you
should clean the bulb before its first use. Take a
clean cloth dipped in a small amount of
rubbing/isopropyl alcohol and gently brush off the
bulb surface. If the lamp is hot, wait 30 minutes
before cleaning.
LIGHT KIT
ASSEMBLY
CAUTION: To reduce the risk of electric shock,
burns or other injury, disconnect the electric supply circuit to the fan before attempting to install
or replace the halogen bulb.
FLAT AREA (3)
GLASS
CAUTION: To not touch halogen bulbs with bare
hands. Fingerprints may result in shorter bulb
life. Remove fingerprints with alcohol.
Figure 19
3. Your ceiling fan is now installed and wire to be
controlled by your remote control system.
LIGHT KIT SOCKET
50-WATT MR-16,
GU-10 HALOGEN
BULB
Figure 18
10
Setting Operating
Frequency of Wall Control
and Receiver (Figure 20)
Installation
of Wall Control
!
Your wall control and receiver have code switches
which must be set in one of 16 possible code combinations. The four levers (numbered 1, 2, 3, and 4) on
the switches are factory-set in the ON (up) position.
Change the switch settings as follows:
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box.
The SW114 wall control transmits the command
signals via radio waves to the SW105 receiver
installed in the ceiling fan ceiling cover. The
SW105 receiver is required for the SW114 wall
control to function. Power for the SW114 wall
control comes from the 12V battery, located in the
wall control.
Replacement 12V batteries recommended are
Duracell MN21 and Eveready A23.
1. Install the 12V battery (supplied) into the wall
control (Figure 21).
2. The SW114 wall control is supplied with a white,
ivory or almond color cover. Choose the style that
best suits your needs and snap the cover onto the
wall control (Figure 21).
1. Slide the four switch levers in the wall control to
your choice of ON (up) or down positions. Use a
ball-point pen or small screwdriver and slide the
levers firmly up or down.
2. In the receiver, slide the four switch levers to the
same positions as set in the wall control. Make
sure the levers on both switches are in the same
positions, otherwise the fan will not operate.
CODE
SWITCH
WARNING
SW105
RECEIVER
ON
HIHI
LIGHT
MED
MED
1
2
3
4
LOW
LOW
WALL CONTROL
LEVERS
ON
REV
REV
FAN OFF
1
2
3
4
RECEIVER SWITCH
LEVERS
HIHI
LIGHT
MED
MED
LOW
LOW
REV
REV
WALL
CONTROL
COVER
FAN OFF
SW114 WALL
CONTROL
Figure 20
CODE
SWITCH
12V BATTERY
SW114 WALL
CONTROL
Figure 21
3. Install the wall control onto the outlet box using the
supplied screws (Figure 22).
4. Install decorator wall plate (not included) using the
two screws provided with wall plate (Figure 22).
OUTLET
BOX
DECORATIVE WALL
PLATE (Not Included)
HI
LIGHT
MED
LOW
REV
FAN OFF
SW114 WALL
CONTROL
WALL PLATE
SCREW (2) WALL CONTROL
SCREW (2)
Figure 22
11
Operating Your Ceiling Fan
Trouble Shooting
Wall Control
IMPORTANT
Fan installation must be completed, including the
installation of the fan blades, before testing of the
wall control.
Fan/Light Fails to Operate
• Check that the wall switch for the ceiling fan is in the “ON”
position.
• Check that the battery is good (red indicator light should
light when any button is pressed).
• Check that the receiver is wired properly.
• Check that both transmitter and receiver code switches
are set in the same position.
Your SW114 Fan/Light Wall Control (Figure 23) has
full control of your fan, lights, and airflow direction.
1. To set the desired fan speed, push the HI, MED, or
LOW buttons to operate your fan on high, medium
or low speed (See Figure 23).
2. To reverse the direction the fan is turning, press
the REV button. The direction the fan turns will
change each time the REV button is pressed.
3. To turn your fan off, press the FAN OFF button.
4. To set the level of light brightness, press and hold
the LIGHT button. The light brightness will continue
to increase then decrease while the button is held
down. When the light is at the desired brightness,
release the button.
5. To turn the light on or off, press and release the
LIGHT button. The light will turn on at the light level
previously set (See Step 4).
Red indicator light turns on when any button is
pressed. If the light does not come on, replace the
battery.
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
!
FAN
SPEED
BUTTONS
LIGHT
MED
LOW
FAN OFF
BUTTON
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
RED
INDICATOR
LIGHT
LIGHT
BUTTON
HI
WARNING
FAN OFF
REV
AIRFLOW
DIRECTION
BUTTON
Accessories
1. Downrod Extension Kits (see store or catalog).
2. Ceiling Fan Controls (see store or catalog).
!
WARNING
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
Figure 23
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
12
INSTRUCTION TO THE USER (if device contains a digital device)
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and
if no installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is not guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC
Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio
and TV reception. The user is cautioned that changes and modifications made to the equipment without the
approval of manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
13
!
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER
BEFORE TROUBLE SHOOTING YOUR FAN.
Trouble Shooting
TROUBLE
PROBABLE CAUSE
SUGGESTED REMEDY
1. Fan will not start. 1. Fuse or circuit breaker blown.
1. Check main and branch circuit fuses or circuit breakers.
2. Loose power line connections to the fan, or loose
switch wire connections in the switch housing.
2. Check line power connections to fan and switch wire
connections in the switch housing.
!
2. Fan sounds
noisy.
3. Fan/Light Wall Control is OFF.
3. Turn ON Fan/Light Wall Control.
4. Code switches in wall control/receiver are
not set in the same position.
4. Check that both code switches are set in the same
positions.
1. Blades not attached to fan.
1. Attach blades to fan before operating.
2. Screws securing fan blades to motor
are loose.
2. Check to make sure the screws which attach the fan blades
to the motor are tight.
3. Wire connectors inside switch housing rattling.
3. Check to make sure wire connectors in switch housing are
not rattling against each other or against the interior wall of
the switch housing.
!
3. Fan wobbles
excessively.
WARNING: Make sure main power is turned off.
WARNING: Make sure main power is turned off.
4. Loose screws in motor housing.
4. Check to make sure all screws in motor housing are snug
(not over-tight)
1. Setscrew in motor coupling is not tightened
securely.
1. Raise coupling cover and tighten setscrew securely.
2. Setscrews in the hanger ball/downrod
assembly are loose.
2. Tighten the setscrews in the hanger ball/downrod assembly.
3. Screws securing fan blade to
motor are loose.
3. Check to be sure screws which attach the fan blade
to the motor are tight.
4. Fan blades are not seated properly.
4. Check to be sure the fan blade flanges seat firmly and
uniformly to the surface of the motor. If blades are seated
incorrectly, loosen the blade screws and retighten.
5. Hanger bracket and/or ceiling outlet box is
not securely fastened
5. Tighten the hanger bracket screws to the outlet box, and/or
secure outlet box.
6. Fan blades out of balance.
6. Interchanging an adjacent (side-by-side) blade pair can
redistribute the weight and result in smoother operation.
Or use supplied balancing kit to balance blades.
14
Repair Parts
2
1
5
3
4
15
10
11
19
18
6
7
9
16
8
23
HIHI
LIGHT
MED
MED
LOW
LOW
REV
REV
FAN OFF
17
24
14
12
20
13
21
15
22
Repair Parts Listing
Part Numbers
Key
No.
Description
Model No.
CF980MBX 00
Model No.
CF980MAB 00
761655-67
—
—
—
761655-67
—
—
—
763415
—
—
—
—
—
—
—
—
—
—
763415
—
—
—
—
—
—
—
—
—
—
*
1
2
3
Hanger Pack, Consisting of:
Hanger Bracket
Hanger Ball
Downrod, 8”
*
4
5
6
7
8
9
10
11
12
13
Parts Bag Containing:
Setscrew Wrench
Threaded Stud, 1-1/4” (2)
Lockwasher (2)
Knurled Knob (2)
Pin, Clevis (1)
Clip, Hairpin (1)
Screw, 1/4-20 x 1/2” Oval Head Flange (9)
Screw, #10-24 x 1/4” Oval Head Blade (13)
Screw, #10-24 x 1” Lower Housing (4)
Screw, #10-24 x 5/16” Pan Head (4)
14
Wiring Harness
763413
763413
15
Ceiling Canopy
763400-BS
763400-BS
16
Coupler Cover
763401-BS
763401-BS
17
Lower Housing
763409-MBX
763409-MAB
18
Blade Assembly (4 per set)
763405-MBX
763405-MAB
19
Flange Assembly (4 per set)
763402-BS
763402-BS
20
Light Kit Assembly
763410
763410
21
Glass
763414
763414
22
SW114 Wall Control
763497
763497
23
SW105 Receiver
762401
762401
24
50-Watt MR-16, GU-10 Halogen Bulb
763494
763494
—
Owner's Manual
BP7353
BP7353
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Part No. F40BP73530000
Printed in China 10/07
Form No. BP7353