Broadcast Tools SS 4.1 III Specifications

INC
®
Installation and Operation Manual
SS 4.1 Plus
Four Input, Single Output Stereo Switcher/Router
Firmware Version 1.10
Manual Update: 06/21/2011
Due to the dynamic nature of product design, the information contained in this
document is subject to change without notice. Broadcast Tools, Inc., assumes no
responsibility for errors and/or omissions contained in this document. Revisions
of this information or new editions may be issued to incorporate such changes.
Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.
tiny TOOLS™ is a trademark of Broadcast Tools, Inc.
All Sentinel™ labeled products are a trademark of Broadcast Tools, Inc.
Copyright ® 1989 - 2009 by Broadcast Tools, Inc. All rights reserved.
No part of this document may be reproduced or distributed without permission.
Visit www.broadcasttools.com for important product update information.
SS 4.1 Plus Installation and Operation Manual
Table of Contents
Section Title
Page #
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Who to Contact for Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rear Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
WEBSITE:
Visit our web site for
product updates and
additional information.
CONTENTS
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
2
SS 4.1 Plus Installation and Operation Manual
INTRODUCTION
Thank you for your purchase of a Broadcast Tools® SS 4.1 Plus, Four Input, Single
Output Stereo Switcher/Router (referred to as the SS 4.1 Plus throughout this manual). We’re confident that this product will give you many years of dependable service.
This manual is intended to give you all the information needed to install and operate the Broadcast Tools® SS 4.1 Plus.
SAFETY INFORMATION
CAUTION!
Broadcast Tools®
Products, as with any
electronic device, can
fail without warning.
Do not use this product
in applications where a
life threatening condition
could result due to failure.
Only qualified personnel should install Broadcast Tools® products. Incorrect or
inappropriate use and/or installation could result in a hazardous condition.
NOTE:
Broadcast Tools, Inc., is unable to support NON-Broadcast Tools software, hardware or
NON-Broadcast Tools computer/hardware/software problems. If you experience these
problems, please research your hardware/software instruction manuals or contact the manufacturers technical support department.
This manual should be
read thoroughly before
installation and operation.
WHO TO CONTACT FOR HELP
If you have any questions regarding your product or you need assistance, please contact your distributor from whom you purchased this equipment.
If you would like more information about Broadcast Tools® products, you may
reach us at:
Broadcast Tools, Inc.
131 State Street
Sedro-Woolley, WA 98284-1540 USA
Voice: 360.854.9559
Fax: 866.783.1742
Internet Home Page: www.broadcasttools.com
E-mail:
support@broadcasttools.com
WEBSITE:
Visit our web site for
product updates and
additional information.
THANK YOU FOR CHOOSING
BROADCAST TOOLS® BRAND PRODUCTS!
INTRODUCTION
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
3
SS 4.1 Plus Installation and Operation Manual
Product Description
The SS 4.1 Plus passively switches any one of four stereo inputs to a single stereo
output and is equipped with eight trigger inputs. Perfect for automation switching
and/or source selection. The passive switching utilizing gold contact relays, which
means that the unit can route a signal in either direction. Due to the passive nature
of the switching, any input level and impedance can be used. Inputs may be balanced or unbalanced, while output levels, impedance, distortion, noise and balancing will match that of the selected input. In addition to their normal use with audio
signals, the unit can also be used to switch composite stereo audio, AES digital audio
signals, RS-232, 422 or 485 data signals and telephone lines.
Features
• Operational control by front panel switches with LED indicators, contact closures, 5volt TTL/CMOS logic levels and/or the multi-drop bi-directional RS-232 serial port.
• May be monitored and/or controlled via a web browser with the optional ESS-1.
• Plug-in euroblock screw terminals are provided for audio and remote control
connections.
• Audio switching via sealed relays utilizing 2-form-C bifurcated - crossbar silver alloy
with gold overlay contacts.
• Internal silence sensor monitors the output and is equipped with a front panel LED indicator; SPST alarm relay and adjustable SS alarm delay and restore timing duration.
ª The “ACT” circuit performs as an audio output activity monitor with front panel LED
indicator.
• The “ENABLE” switch provides a safety lock to the front panel source selection
switches.
• The audio “MUTE” switch allows the user to turn off the audio output when activated.
• The “STEP” function allows the user to single step through each channel or to automatically sequence with user programmed channel steps and speed.
• Eight remote inputs, user configured for remote control or “PIP” (trigger) inputs.
• Four open collector outputs provide remote channel status.
• Logic functions via flash microprocessor with non-volatile memory.
• The power-up feature allows the user to select which one source is active at power up,
including the last source selected.
• Configuration via dipswitches, serial port menu or burst mode.
• Source number one is configured to route audio to the output in the case of loss of
power to the unit.
• Non-selected sources are terminated with 10K W load resistors. May be removed.
• The SS 4.1 Plus may be set on a desktop, mounted on a wall or up to three units on
one RA-1 rack shelf.
Applications
Automation source switching with eight trigger inputs; Studio selection and routing;
Audio processing selection; Exciter input selection; Remote broadcast input selection; STL source selection; Multiple station program on-hold and/or PA switching;
EAS audio switching; ISDN or Phone hybrid feed selection; IFB selection; Satellite
audio channel switching and console monitor inputs and outputs selection.
DESCRIPTION
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
4
SS 4.1 Plus Installation and Operation Manual
Front Panel Description
Source Switches
Each switch represents an input to be routed to the switcher’s output. High quality
tactile switches will give the user years of dependable service. Each switch has an
associated LED indicator, which will illuminate when that particular source is routed to the output. When a source is selected, the previous source will be deselected,
(interlocked). The front panel is also equipped with a MUTE switch and LED indicator. This switch turns off the audio output. The ENABLE switch (if recessed, it
may require the use of a toothpick), when enabled, must be depressed in order for
any of the other switches to function. This function may be bypassed (default).
LED Indicators
Channel LED indicators will illuminate when the desired channel is selected. The
PWR LED displays valid power and TX/RX serial data activity. The mute LED illuminates when audio is off. The “ACT” (activity) LED is lit when audio is present
at the output. The silence sensor LED will illuminate when in an alarm condition.
Audio thresholds are set at -25db.
Rear Panel Description
The rear panel audio inputs, outputs and remote control (triggers) connections are
routed through plug-in euroblock screw terminals. A RJ-11 modular jack is provided for the multi-drop bi-directional RS-232 serial port.
Power
Connect the 2.1mm coaxial type power connector into the unit and the 9 VAC @ 1amp wall transformer into a 120 Vac 50-60 Hz power source. The front panel PWR
LED indicates when power is applied to the unit.
Audio Signal Connector
The SS 4.1 Plus is supplied with plug-in euroblock screw terminals and mating connectors. Channel and polarity designators can be found on the chassis, as viewed
from the rear.
WEBSITE:
Visit our web site for
product updates and
additional information.
“Remote” Control Connector
Plug-in euroblock screw terminals and mating plugs are provided for connection to
equipment, which will remotely control the SS 4.1 Plus, unless the “PIP” (triggers)
function is enabled. Pulsing the “MUTE” input to ground (low) would turn off the output of the SS 4.1 Plus until a front panel source switch is pressed, a remote control
input is activated, the unit is powered up and/or a serial command is received from a
PC or other serial device. Pulsing the “STEP” input to ground will step the unit one
source for each low to high transition on this input. Automatic sequence may be
accomplished by holding the step input low for two seconds. The unit will now step
to each source at a user programmable rate from 1 to 99 seconds. The number of
inputs sequenced may be programmed for channels 1 to 4. The step input is helpful
in freeing up valuable remote control channels. This feature may also be used to
sequence through multiple station air monitor signals for program on-hold feed.
DESCRIPTION
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
5
SS 4.1 Plus Installation and Operation Manual
Installation Guidelines
It is recommended that all cables connected to the SS 4.1 Plus be looped through ferrite cores to suppress RF. Surge protection with RF filtering such as the Tripp Lite
“ISOBAR 4” is also suggested for the power transformer. The purchase of an inexpensive uninterruptible power supply (UPS) will provide back up in case of power
outages. Check out our web site for lightning protection links.
The SS 4.1 Plus is simple to install. The signal inputs, outputs are connected via
plug-in euroblock screw terminals. Installation of the SS 4.1 Plus consists of seven
steps:
1.
2.
3.
4.
5.
6.
7.
Inspection
Removal of the source termination resistors, if applicable
Bench test and option set-up
Mount the unit in a rack (RA-1), desktop or wall
Connect your equipment to the unit
Label the front panel switches
Serial operation, if applicable
STEP 1: INSPECTION
Please examine your SS 4.1 Plus carefully for any damage that may have been
sustained during shipping. If any is noted, please notify the shipper immediately and retain the packaging for inspection by the shipper. The package should
contain the SS 4.1 Plus, this manual and/or CD (the manual may be downloaded
from our web site), 9 VAC @ 1-amp transformer, reversed modular cable, 9-pin
female “S9” D-Sub adapter and audio and remote control mating connectors.
STEP 2: SOURCE TERMINATION RESISTOR REMOVAL
CAUTION!
Installation of the SS 4.1
Plus in high RF environments should be performed with care.
Shielded cable is suggested for all control,
audio inputs and outputs. All shields should
be tied to the “GND”
terminal. The station
ground should be connected to the chassis
ground screw (CH1)
located behind J1, as
viewed from the rear.
For lightning protection,
check
out
www.polyphaser.com
and www.itwlinx.com
WEBSITE:
Visit our web site for
product updates and
additional information.
Input sources that are NOT selected are terminated with a 10K W resistor. If you
do not require this load applied to the deselected sources, it may be removed from
each channel. Each channel has a pair of resistors. Removal information: Channel
1 = R 8 & R9. Channel 2 = R10 & R11.
Channel 3, R12 & R13 and Channel 4 = R14 & R15. If the unit is to be used for
applications other than switching audio, the Silence Sensor and ACT detection circuit should be disabled. To disable, remove the following components: R24, R25
and RP9.
INSTALLATION
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
6
SS 4.1 Plus Installation and Operation Manual
STEP 3: BENCH TEST and OPTIONS
Place each unit on a workspace and connect power to the unit. Check to see if LED
#1 (Channel 1) and the PWR LED are lit (Source one is the power-up factory
default). Connect an audio source to stereo input one and a monitoring device to the
output. Verify that audio is present. Repeat the process until each channel’s operation has been verified.
Jumper JP2
! TIP
The “ACT” (audio
activity) LED is an
excellent audio output
indicator.
To enable the front panel “ENABLE” switch, remove and stow the jumper over
the “Enable Bypass” jumper JP2.
Note: The “Enable” switch is disabled at the factory.
Dipswitches:
DIP (SW6) Switch Functions
Unit ID SW6-1
SW6-2
ID 0 *
OFF
OFF
ID 1
ON
OFF
ID 2
OFF
ON
ID 3
ON
ON
ID 4
OFF
OFF
ID 5
ON
OFF
ID 6
OFF
ON
ID 7
ON
ON
Baud RateSW6-4
2400
ON
9600 * OFF
4800
OFF
38400
ON
SW6-5
OFF
OFF
ON
ON
Power Up
User selected
Last source
selected *
SW6-6
ON
OFF
Remote/PIP
PIP / Triggers
Remote Control *
SW6-7
ON
OFF
SW6-3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
NOTE:
Input selection at
power-up may be configured by holding down
the desired channels
push button until the
mute and Pwr/Ser
LED’s flash. Factory
power-up default is
channel one.
Note:
* Denotes factory setting.
Note: After changing any dipswitch, please repower the unit.
INSTALLATION
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
7
SS 4.1 Plus Installation and Operation Manual
STEP 4: MOUNTING
Mount the unit on a rack shelf, such as the Broadcast Tools RA-1, allowing adequate
airflow for cooling. The RA-1 is furnished with filler panels to cover open spaces.
Up to three units may be installed on one RA-1.
STEP 5: CONNECT YOUR EQUIPMENT
The SS 4.1 Plus interfaces to your equipment (sources and loads) through the rear
panel plug-in euroblock screw terminals. Follow the legends for the desired audio
input, output and remote control connections, which appear on the rear side of the
chassis. Before installing a wire, remove the plug-in euroblock screw terminal and
turn each capture screw fully counterclockwise. Strip each conductor to a length of
0.25” and insert the conductor fully into the terminal. Turn the capture screw fully
clockwise to secure the conductor. The terminals accommodate wire sizes from 16
- 28 AWG solid or stranded wire.
Control
The front panel functions are brought out through the rear panel “REMOTE” (Inx)
connector TB 4, providing a means of controlling the SS 4.1 Plus from a remote
point. The channel select inputs may be connected to any remote pair of switch contacts and ground, such as external relays, switches, open-collector circuits, contact
closures or 5-volt TTL/CMOS logic signals.
WEBSITE:
Visit our web site for
product updates and
additional information.
INSTALLATION
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
8
SS 4.1 Plus Installation and Operation Manual
Status
The status signals are supplied through the “Remote” control connector TB-3 as
individual open collectors. The open collectors may be used to provide status to a
remote control point to indicate which source is selected. The status open collector
(OCx) output for the selected channel will go low providing a return for an LED
indicator, TTL/CMOS logic or relay. External pull-up resistors may be required in
some installations.
Connecting the remote control, PIP / Trigger Inputs and OC’s / SS Relay
Most front panel functions of the SS 4.1 Plus may be remote controlled via the pluggable euroblock screw terminals located on the rear panel. The SS 4.1 Plus accepts
momentary contact closures (sustained, if break before make); open collector or
TTL/CMOS input logic levels. Connections to the remote control and/or PIP (trigger) inputs are made on the TB-4. The following information is a comparison chart
to be used when connecting external devices.
Rear Panel Connectors
TB 1 —> TB 2
Input x – Left
Input x – Left
EVEN Inputs
Input x + Left
Gnd
Input x + Left
Gnd
ODD Inputs
Top Row
Input x – Right Input x + Right
Input x – Right Input x + Right
Bottom Row
TB 3
Audio Output
Top Row
Output - Left Output + Left
Gnd
Output - Right
Output + Right
Open Collector 1
Open Collector 2
Gnd
Open Collector 3 Open Collector 4
Open Collector Outputs
Bottom Row
TB 4
PIP 4
PIP 5
SS Relay N.O.
Remote input / Triggers
PIP 6
PIP 7
PIP 8
Gnd
SS Relay CM
PIP 1
PIP 2
SS Relay & Remote Inputs / Triggers
Top Row
PIP 3
Gnd
Bottom Row
Note: Remote control cross-reference information is on the next page.
INSTALLATION
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
9
SS 4.1 Plus Installation and Operation Manual
Remote Control
TB 4 Pin
Function (DIPSw 6-7 = OFF).
BOT 1
Silence Sensor Relay N.O.
BOT 2
Silence Sensor Relay CM
BOT 3
IN 1, selects channel ONE
BOT 4
IN 2, selects channel TWO
BOT 5
IN 3, selects channel THREE
BOT 6
GND
TOP 1
IN 4, selects channel FOUR
TOP 2
Mute, turns OFF ALL channels
TOP 3
Step, Steps through selected channels
TOP 4
N/A
TOP 5
N/A
TOP 6
GND
Function (DIPSw 6-7 = ON)
Silence Sensor Relay N.O.
Silence Sensor Relay CM
PIP 1
PIP 2
PIP 3
GND
PIP 4
PIP 5
PIP 6
PIP 7
PIP 8
GND
STEP 6: LABEL SWITCHES
Write the source descriptions under each source switch, if desired.
STEP 7: SERIAL OPERATION
The supplied reversed modular cable and 9-pin female (S9) D-sub adapters may be
connected to the SS 4.1 Plus’s rear panel modular connector. Plug in the female DB9 D-sub adapter into your computer’s serial port. Plug the supplied wall transformer
into a source of 117 vac and the cable end of the transformer into the power receptacle on the SS 4.1 Plus. The protocol is as follows: 2400, 4800, 9600, 38400, 8N1.
Flow control should be set to NONE, emulation to ANSI and the mode should be set
to DIRECT TO COMx (x = the available com port). The default is 9600, 8,N,1.
Commands
*uii
EXAMPLE:
*uMA
*uCA
*uCDEF
*uCIIttt
*CLx
*uCFSx
*uCSLx
*uCSTtttt
*uDxx
*POLL
*uSL
*uSPi
*0SS
*uSPA
*uU
*uY
*uZx
*uMM
Turn on input ii
*004 This string would turn on channel 4 on unit 0
Mute audio output (Turn Off Audio)
Set active channel for power up
Reset to factory defaults
Set PIP minimum pulse length ttt: 000 – 255 => off to 2.55 seconds
Lock front panel. x = L (Lock) x = U (Unlock)
Set first step channel to x. x = 1 –> 4, 0 to disable
Set last step channel to x.
x = 1 –> 4, 0 to disable
Set step interval in tenths:
0000 –> 99, Off to 99 seconds
Delay xx seconds before processing the next command
Display unit ID in appropriate time slot
Send Audio Status: SuL1,x,x,x,x,x<cr><lf>
Note: x: 0 = Not Connected / x: 1 = Connected
Send single PIP status i: SuP,i<cr><lf>
Send Silence Sensor Status
Response Example: S0S,0 = OK / S0S,1 = Alarm
Send PIP status: SuP,A,x,x,x,x,x,x,x,x<cr><lf>
Send unit info: name><firmware version><cr><lf>
Display configuration
Echo character x to serial port (Used to debug command strings)
Enter menu mode
WEBSITE:
Visit our web site for
product updates and
additional information.
INSTALLATION
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
10
SS 4.1 Plus Installation and Operation Manual
Menu:
The menu allows the selection of PIP (eight triggers) hold time, silence sensor delay
and restore time, step time, the selection of the last channel in the step, front panel
lock, audio channel selection with status and audio status.
The stepping time can be between 1 and 99 seconds. The last channel step is selectable from channels 1 through 4.
Serial:
Pin out of the RJ-11 modular/”S9” female DB-9 D-Sub adapter is shown below.
RJ-11
Adapter
Pin
4
DB-9
D-Sub
SS 4.1 Plus
(Point of view)
3
RS-232 Receive
3
2
RS-232 Transmit
2
5
Ground
Modular connectors point of view.
Modular Jack
Pin Numbers
INSTALLATION
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
11
SS 4.1 Plus Installation and Operation Manual
Specifications
Inputs/Outputs:
Any input level and impedance can be used. Inputs may be balanced or unbalanced. Output levels, impedance, distortion,
noise and balancing will match that of the selected input.
Switching Method:
Passive, sealed relays utilizing 2-form-C bifurcated - crossbar
silver alloy with gold overlay contacts.
Logic:
Flash microprocessor with non-volatile memory.
Operation Control:
Front Panel - Momentary push button switches
Remote - Momentary or sustained (break before make), compatible with 5 volts CMOS/TTL logic, open collector or contact
closures to ground. 50 ms response time in (PIP) trigger mode.
Serial - Multi-drop RS-232, Bi-directional, 2400, 4800, 9600,
38400, 8,N,1.
Status:
Front Panel - Indicator LED’s.
Remote – Audio “ACTivity” LED – Trip level set at -25db.
Remote - “SS” LED & Silence Sensor SPST relay – Trip level
set at –25db
Remote - Open collector outputs, 6 vdc and current limit to 50
ma per output. Pull-ups may be required.
Interfacing:
Audio & Remote Control – Plug-n euroblock screw terminals.
RS-232 - 4C6P Modular. Mating reversed modular cable and
(S9) adapter supplied.
Power Requirements:
9 Vac, 1-amp, 120 Vac 50-60 hz transformer (supplied).
(CE 240 Vac 50-60 Hz optional)
Physical Dimensions:
5.50” x 6.50” x 1.55” (WDH)
Weight:
2.0 lb.
Shipping Weight:
3.0 lb.
Options:
RA-1 rack shelf holds three units (1-RU) / Filler panels supplied.
WEBSITE:
Visit our web site for
product updates and
additional information.
SPECIFICATIONS
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
12
SS 4.1 Plus Installation and Operation Manual
LIMITED WARRANTY
The term “Buyer” as used in this document refers to and includes both (but only) (a) any person or entity who acquires such an item for
the purpose of resale to others (i.e., a dealer or distributor of an item), and (b) the first person or entity who acquires such an item for
such person’s or entity’s own use.
Broadcast Tools warrants to each Buyer of any item manufactured by Broadcast Tools that the item will be free from defects in materials and workmanship at the time it is shipped by Broadcast Tools if the item is properly installed, used and maintained.
EXCLUSIVE REMEDIES
If Broadcast Tools is notified, in writing, of a failure of any item manufactured by Broadcast Tools to conform to the foregoing Limited
Warranty within one (1) year following the date of the Buyer’s acquisition of the item, and if the item is returned to Broadcast Tools in
accordance with Broadcast Tools’ instructions for confirmation by inspection of the defect (which at Broadcast Tools’ election may
include, without limitation, a requirement that the Buyer first obtain a Return Authorization number from Broadcast Tools, that the Buyer
furnish proof of purchase in the form of an invoice and/or receipt, and that the Buyer prepay all freight charges associated with any return
of the item to Broadcast Tools using such freight service as Broadcast Tools reasonably may specify), Broadcast Tools will repair or
replace the defective item, or will refund the purchase price paid by the Buyer for the item. Broadcast Tools shall have the exclusive
right to choose between these alternative remedies.
NO OTHER WARRANTIES OR REMEDIES
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, BROADCAST TOOLS AND ITS SUPPLIERS DISCLAIM ALL OTHER
WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE; AND THE FOREGOING ALTERNATIVE REMEDIES SHALL BE EXCLUSIVE OF
ALL OTHER REMEDIES. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS,
WHICH VARY FROM STATE/JURISDICTION TO STATE/JURISDICTION.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, NEITHER BROADCAST TOOLS NOR ANY OF ITS SUPPLIERS
SHALL HAVE ANY LIABILITY FOR ANY SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENTIAL OR PUNITIVE DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, ANY DAMAGES FOR LOST PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA OR
INFORMATION, COST OF CAPITAL, CLAIMS OF CUSTOMERS, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE
OF OR THE INABILITY TO USE ANY ITEM SUPPLIED BY BROADCAST TOOLS, EVEN IF BROADCAST TOOLS HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HAVE ANY LIABILITY FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL,
EXEMPLARY OR PUNITIVE DAMAGES. THIS LIMITATION OF LIABILITY APPLIES WHETHER A CLAIM IS ONE ALLEGING
BREACH OF A CONTRACT OR WARRANTY, NEGLIGENCE OR OTHER TORT, FOR THE VIOLATION OF ANY STATUTORY DUTY,
THE FAILURE OF ANY LIMITED OR EXCLUSIVE REMEDY TO ACHIEVE ITS ESSENTIAL PURPOSE, OR ANY OTHER CLAIM OF
ANY NATURE. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, THIS LIMITATION MAY NOT APPLY TO YOU.
Broadcast Tools, Inc.
131 State Street
Sedro-Woolley, WA 98284 • USA
360.854.9559 voice • 866.783.1742 fax
support@broadcasttools.com e-mail
www.broadcasttools.com website
LIMITED WARRANTY
e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742
13