Allied Telesis AR450S Specifications

A5 Installation and Safety Guide Cover
AR400 Series Router
Installation and Safety Guide
AR410
AR410S
AR415S
AR440S
AR441S
AR442S
AR450S
613-000313 REV B
2
AR400 Series Router
AR400 Series Installation and Safety Guide
Document Number 613-000313 Rev B.
Copyright © 2004-2006 Allied Telesis Inc.
19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA.
All rights reserved. No part of this publication may be reproduced without prior
written permission from Allied Telesis.
Allied Telesis Inc. reserves the right to make changes in
specifications and other information contained in this document without prior
written notice. The information provided herein is subject to change without
notice. In no event shall Allied Telesis be liable for any incidental, special,
indirect, or consequential damages whatsoever, including but not limited to lost
profits, arising out of or related to this manual or the information contained
herein, even if Allied Telesis has been advised of, known, or should have known,
the possibility of such damages.
All trademarks are the property of their respective owners.
613-000313 Rev B
Installation and Safety Guide
3
Table of Contents
Electrical Safety Statements ................................................................................................... 4
Package Contents .................................................................................................................... 5
AR410, AR410S, AR450S Routers ...................................................................................... 6
Installing the AR410, AR410S and AR450S ................................................................6
Configuring the AR410, AR410S, AR450S .................................................................8
Connecting Data Cables to AR410, AR410S, AR450S ......................................... 12
System LEDs on AR410, AR410S, AR450S ............................................................. 13
AR415S Router ...................................................................................................................... 14
Installing the AR415S .................................................................................................... 14
Configuring the AR415S .............................................................................................. 18
Connecting Data Cables to AR415S ......................................................................... 23
System LEDs on AR415S ............................................................................................. 24
AR440S, AR441S, AR442S Routers .................................................................................. 25
Installing the AR440S, AR441S, AR442S .................................................................. 25
Configuring the AR440S, AR441S, AR442S ............................................................ 29
Connecting Data Cables to AR440S, AR441S, AR442S ....................................... 35
System LEDs on AR440S, AR441S, AR442S ........................................................... 36
Default Configuration on AR415S, AR440S, AR441S, AR442S .................................. 37
Documentation and Tools CD-ROM ................................................................................ 38
Connection to mains voltage supply ................................................................................. 39
Telecommunications Interfaces .......................................................................................... 39
Safety ........................................................................................................................................ 41
Sicherheit ................................................................................................................................. 42
Sikkerhed ................................................................................................................................. 43
Veiligheid .................................................................................................................................. 44
Sécurité .................................................................................................................................... 45
Turvallisuus .............................................................................................................................. 46
Norme di Sicurezza ............................................................................................................... 47
Sikkerhet .................................................................................................................................. 48
Segurança ................................................................................................................................. 49
Seguridad ................................................................................................................................. 50
Säkerhet ................................................................................................................................... 51
US Federal Communications Commission (FCC) ......................................................... 52
Canadian Department of Communications ..................................................................... 53
Emission Compliance Statements ...................................................................................... 54
EC Declaration of Conformity ........................................................................................... 56
613-000313 Rev B
4
AR400 Series Router
Electrical Safety Statements
Electrical Safety
IMPORTANT: This equipment must be installed in accordance with safety
precautions (“Safety”, page 41).
Elektrische Sicherheit
WICHTIG: Für die Installation dieses Gerätes ist die Einhaltung von
Sicherheitsvorkehrungen erforderlich (“Sicherheit”, Seite 42).
Elektrisk sikkerhed
VIGTIGT: Dette udstyr skal installeres i overensstemmelse med
sikkerhedsadvarslerne (“Sikkerhed”, side 43).
Elektrische veiligheid
BELANGRIJK: Dit apparaat moet in overeenstemming met de
veiligheidsvoorschriften worden geïnstalleerd (“Veiligheid”, pagina 44).
Sécurité électrique
IMPORTANT: Cet équipement doit être utilisé conformément aux instructions de
sécurité (“Sécurité”, page 45) .
Sähköturvallisuus
TÄRKEÄÄ: Tämä laite on asennettava turvaohjeiden mukaisesti (“Turvallisuus”,
sivu 46).
Sicurezza elettrica
IMPORTANTE: questa apparecchiatura deve essere installata rispettando le norme
di sicurezza (“Norme di Sicurezza”, pagina 47).
Elektrisk sikkerhet
VIKTIG: Dette utstyret skal installeres i samsvar med sikkerhetsregler (“Sikkerhet”,
side 48).
Segurança eléctrica
IMPORTANTE: Este equipamento tem que ser instalado segundo as medidas de
precaução de segurança (“Segurança”, página 49).
Seguridad eléctrica
IMPORTANTE: La instalación de este equipo deberá llevarse a cabo cumpliendo con
las precauciones de seguridad (“Seguridad”, página 50).
Elsäkerhet
OBS! Alla nödvändiga försiktighetsåtgärder måste vidtas när denna utrustning
används (“Säkerhet”, sida 51).
613-000313 Rev B
Installation and Safety Guide
5
Package Contents
Contact your authorised distributor or reseller if any items are damaged or missing.
Item included for each router
AR410 AR440S
AR410S AR441S
AR415S AR442S
AR450S
One AR400 Series router
✔
✔
✔
One AC power cord
✔
✔
✔
One power cord retaining clip
✔
✔
✔
One serial cable for connecting the router to a
terminal or PC
✔
✔
✔
✔
✔
One serial null modem cable for connecting the
router to a terminal or PC
Two UTP network cables
✔
✔
One DSL cable
AR440S: two in Australia, New Zealand
One 19 inch rack-mount kit
✔
✔
✔
One AR400 Series Router Installation and Safety Guide
✔
✔
✔
One AR400 Series Router Documentation and Tools
CD-ROM (includes the complete AR400 Series
Document Set and utilities)
✔
✔
✔
One warranty card
✔
✔
✔
To install your router, see “AR410, AR410S, AR450S Routers” following, “AR415S
Router” on page 14, or “AR440S, AR441S, AR442S Routers” on page 25.
613-000313 Rev B
6
AR400 Series Router
AR410, AR410S, AR450S Routers
This section describes how to install the AR410, AR410S and AR450S routers.
■
“Installing the AR410, AR410S and AR450S” below
■
“Configuring the AR410, AR410S, AR450S” on page 8
■
“Connecting Data Cables to AR410, AR410S, AR450S” on page 12
■
“System LEDs on AR410, AR410S, AR450S” on page 13
For corresponding information about installing an AR415S, see “AR415S Router” on
page 14.
For corresponding information about installing an AR440S, AR441S or AR442S, see
“AR440S, AR441S, AR442S Routers” on page 25.
Installing the AR410, AR410S and AR450S
Selecting a Site
You can install the router:
■
on a level surface such as a desktop or bench
■
in a standard 19-inch rack, using the rack-mount kit supplied with the router
When you install the router, choose a site that:
■
allows adequate airflow around the router and its vents
■
is free of dust and moisture
■
will maintain ambient temperature in the range 0º C to 40º C (32º F to 104º F)
and humidity in the range 5% to 80% non-condensing
■
has a reliable and earthed (grounded) power supply, preferably dedicated and
filtered
■
does not expose cabling to sources of electrical noise such as radio transmitters,
broadband amplifiers, power lines, electric motors, and fluorescent fixtures
■
allows easy access to the router’s power and cable connections
Before Installing the Router
■
Read the safety information in “Safety” on page 41.
■
Unpack the router. Verify the package contents. If any items are damaged or
missing, contact your sales representative.
Installing an Optional PIC
If you purchased an optional PIC for your AR410 or AR410S, install it now by
following the Port Interface Card Quick Install Guide. The PIC Quick Install Guide can
be found with the PIC, on the Documentation and Tools CD-ROM, or can be
downloaded from www.alliedtelesyn.com/support/software/.
613-000313 Rev B
Installation and Safety Guide
7
Installing the Router in a Rack
1. Gather additional items. You will need:
•
the rack-mount kit included in the router package
•
a Phillips #1 screwdriver
•
screws and cage nuts to attach the brackets to your rack
2. Check the rack.
Ensure that the rack is safely secured and that it will not tip over. Devices in a
rack should be installed starting at the bottom, with the heavier devices near the
bottom of the rack.
Ensure the rack has sufficient space for the router and its associated cables. The
router is 1U high.
3. Unscrew the feet from the router.
4. Connect the handles to the brackets.
Screw the handles to the wider side of each bracket, using the supplied screws.
5. Connect the brackets to the router.
Screw the brackets to the sides of the router, using the supplied screws. The
router can be front or rear mounted.
6. Mount the router in the rack.
Use appropriate rack mounting screws (not supplied).
Applying Power to the Router
1. Check the supply voltage and the router’s rated voltage.
The router is fitted with a universal mains power supply that will function over
the range 100-240 VAC and 50–60Hz.
For continued protection against the risk of fire and shock hazard, replace fuses
only with fuses of the same type and rating.
Warning The specific power supply requirements for a particular model are
clearly displayed on the rear or underside of the router. If the supply is outside
the accepted range for the router, the router may not operate or damage to
the router may result.
2. Fit the power cord retaining clip to the AC power inlet on the router’s rear panel.
613-000313 Rev B
8
AR400 Series Router
3. Connect the provided power cord to the AC power inlet and clip it in place.
Switch the router’s power switch to the ON position. The Power LED lights
continuously and the System LED lights briefly. The Port LEDs also light briefly.
The router is supplied with an approved power cord that incorporates a
moulded plug. It must only be used with the power cord supplied.
If the LEDs fail to light, the most likely cause is that the router is not receiving
power. Check that:
■
the power supply outlet’s switch (if any), and the router’s power switch, are in
the ON position
■
the power cable is securely plugged in
■
the power supply is operational
Configuring the AR410, AR410S, AR450S
You can configure the router via the command line interface (CLI) or the graphical
user interface (GUI). First use the CLI to assign an IP address to the router, then use
the CLI or the GUI to complete the configuration.
■
“Using the CLI to Configure AR410, AR410S, AR450S” below
■
“Using the GUI to Configure AR410, AR410S, AR450S” on page 10
Using the CLI to Configure AR410, AR410S, AR450S
This section describes how to access the router’s command line interface (CLI)
using a terminal or PC connected to the router’s console port.
1. Initiate router start-up.
Using the terminal cable supplied, connect a VT100-compatible terminal, or the
COM port of a PC running a terminal emulation program such as Windows
Hyper Terminal, to the Console RS-232 (ASYN0) port on the router’s rear
panel.
Set the communication parameters on your terminal or terminal emulation
program to:
•
Baud rate: 9600
•
Data bits: 8
•
Parity: None
•
Stop bits: 1
•
Flow control: Hardware
See the AR400 Series Router Hardware Reference for more information on
configuring emulation software.
613-000313 Rev B
Installation and Safety Guide
9
2. Log in and set the password.
The login prompt appears on the terminal or PC. If the login prompt does not
appear, press [Enter] two or three times.
When the router boots for the first time it automatically creates an account
with manager privileges. The account has the user name “manager” and the
password is “friend”. Passwords are case sensitive.
At the login prompt, enter the user name and password.
Login: manager
Password: friend
The router’s command prompt appears and you can now configure the router
using the command line interface.
Warning Change the password as soon as possible. Leaving the manager
account with the default password is a serious security risk. Make sure you
remember the new password as there is no way to retrieve it if it is lost.
Use the following command to change the account password:
set password
3. Configure the router.
See the AR400 Series Router Software Reference for more information on router
start-up and configuration procedures (including a list of message definitions). To
continue configuring the router using the CLI, use the commands in the
Software Reference.
To display a list of help topics, enter:
help
To display help on a specific topic, enter:
help topic
Alternatively, type a question mark (?) at the end of a partially completed
command to see a list of valid options.
4. Save the configuration.
Save your configuration to a new file by using the command:
create config=filename.cfg
Then set the router to load this file when it restarts by using the command:
set config=filename.cfg
We recommend leaving the boot.cfg file unchanged, in case you need to revert
to the original default configuration.
To continue configuring the router using the GUI, see the following section.
613-000313 Rev B
10
AR400 Series Router
Using the GUI to Configure AR410, AR410S, AR450S
This section describes how to access the GUI via a switch port in VLAN1 on the
AR410, AR410S, AR450S routers, when the PC and the router are in the same
subnet, in order to configure the router. The router’s switch ports all belong to
VLAN1 by default.
The GUI requires a PC and web browser. Supported browsers are Internet Explorer
5.0 or later and Netscape 6.2.2 or later, with JavaScript enabled. If you are using a
toolbar or plug-in on your browser to block pop-ups, disable it while using the GUI.
The GUI displays detailed configuration options and information in pop-up windows.
1. Connect the PC to a router switch port.
The PC can be connected either directly or through your LAN.
To connect the PC directly to the router, use a straight-through Ethernet cable
to connect an Ethernet card on the PC to any one of the router’s switch ports.
Note the PC’s IP address and mask.
straight-through cable
router
RS-232
ON
10BASE-T/100BASE-TX SWITCH PORTS
ETHERNET
1 DMZ
0 WAN
5
4
3
2
1
OFF
ASYN1
ASYN0 CONSOLE
POWER
switch ports
PC
To connect via a LAN, use an Ethernet cable to connect the router’s switch
port(s) to the device(s) on the LAN. Connect AR410 and AR410S routers
through port 4 and ensure that the PC/hub switch is pressed in. Select the LAN
PC from which you wish to configure the router. The PC should be in the same
subnet as the part of the LAN that contains the router (for example, the PC
could be connected to a hub or Layer 2 switch that is directly connected to one
of the router’s switch ports). Note the PC’s IP address and mask.
RS-232
ON
10BASE-T/100BASE-TX SWITCH PORTS
ETHERNET
ON
1 DMZ
0 WAN
5
4
3
2
1
10BASE-T/100BASE-TX SWITCH PORTS
4
3
2
OFF
ASYN0 CONSOLE
POWER
OFF
POWER
switch ports
PC
613-000313 Rev B
hub or layer 2
switch
ASYN1
1
router
Installation and Safety Guide
11
2. Access the CLI on the router.
Follow the instructions in the previous section “Using the CLI to Configure
AR410, AR410S, AR450S” on page 8.
3. Enable IP.
In the CLI, enter the command:
enable ip
4. Assign an IP address to VLAN1.
Assign the VLAN1 interface an IP address in the subnet that the PC uses, using
the command:
add ip interface=vlan1 ip=ipaddress mask=mask
5. Browse to the GUI.
If you access the Internet through a proxy server, set your browser to bypass
the proxy for the IP address you assigned to the VLAN1 interface.
Point your web browser at the IP address of the VLAN interface.
6. Log in and set the password.
At the log in prompt, enter the log in name and password. Passwords are case
sensitive.
User Name: manager
Password: friend
The system status page appears and you can now use the GUI to configure the
router.
Important To ensure configuration settings are saved correctly, use the GUI
menus and buttons to navigate, not your browser’s buttons.
Caution As a security precaution, change the password as soon as
possible.
To change the password, select Management > Users from the sidebar menu.
Select the Manager account and click Modify.
7. Configure the router.
Use the GUI to continue configuring your router. To access context-sensitive
help in the GUI, click on the Help button [Help]. The Help button is located at
the top of the sidebar menu or on any popup page.
613-000313 Rev B
12
AR400 Series Router
Connecting Data Cables to AR410, AR410S, AR450S
Connecting the router to your network:
1. Connect to the LAN.
If you have not already done so, use straight-through Ethernet patch cables to
connect the device(s) on your private network (LAN) to the router’s switch
port(s). By default, all switch ports are members of VLAN1.
2. Connect to the DMZ port.
AR410, AR410S: If you have public servers to connect, connect them to switch
ports in a different VLAN. For information about configuring VLANs, see the
Switching chapter in the Software Reference.
AR450S: If you have a public server to connect, use an Ethernet patch cable to
connect it to the AR450S router’s Ethernet DMZ (ETH1) port. Separating public
servers from your LAN allows the firewall to provide greater protection for
your LAN. If you have multiple public servers, you can connect them to a hub or
Layer 2 switch and connect that device to the router’s DMZ port.
3. Connect to the WAN.
Caution If you intend to use a firewall, configure it before you activate
the WAN link.
Once initial configuration is complete, connect the router to the WAN:
•
AR410, AR410S: Connect a PIC port to a WAN connection. See the Port
Interface Card Quick Install Guide and Hardware Reference.
•
AR410, AR410S, AR450S: Use an Ethernet patch cable to connect the
router’s Ethernet WAN (ETH0) port to the Ethernet port of a WAN device
(such as a modem).
613-000313 Rev B
Installation and Safety Guide
13
System LEDs on AR410, AR410S, AR450S
The LEDs described in the following table show the operational status and port
activity for the AR410, AR410S and AR450S routers.
LED
State
Function
Power
Green
The router is receiving power and the power switch is
ON.
System
Red or
Amber
Lit briefly during router start up, or the router is
malfunctioning.
Flashing
The fan has failed.
Off
Normal operation.
PIC
Green
(AR410,
AR410S)
A port interface card (PIC) is correctly installed and has
been detected by the router.
Off
No PIC is installed, or the router has not recognised the
PIC.
Full Dup
Green
The port is operating at full-duplex.
Off
The port is operating at half-duplex.
Green
A link has been established.
Flashing
Data is being transmitted.
Off
No link is present.
Green
The port is operating at 100Mbps.
Off
The port is operating at 10Mbps.
Link/ACT
100M
613-000313 Rev B
14
AR400 Series Router
AR415S Router
This section describes how to install the AR415S router.
■
“Installing the AR415S” below
■
“Configuring the AR415S” on page 18
■
“Connecting Data Cables to AR415S” on page 23
■
“System LEDs on AR415S” on page 24
For corresponding information about installing an AR410, AR410S or AR450S, see
“AR410, AR410S, AR450S Routers” on page 6.
For corresponding information about installing an AR440S, AR441S or AR442S, see
“AR440S, AR441S, AR442S Routers” on page 25.
Installing the AR415S
Selecting a Site
You can install the router:
■
on a level surface such as a desktop or bench
■
in a standard 19-inch rack, using the rack-mount kit supplied with the router
■
on a firm wall, using a wall-mount kit ordered from your authorised distributor
or reseller
When you install the router, choose a site that:
■
allows adequate airflow around the router and its vents
■
is free of dust and moisture
■
will maintain an ambient temperature in the range 0º C to 40º C
(32º F to 104º F)
■
will maintain a humidity in the range 5% to 80% non-condensing
■
has a reliable and earthed (grounded) power supply, preferably dedicated and
filtered
■
does not expose cabling to sources of electrical noise such as radio transmitters,
broadband amplifiers, power lines, electric motors, and fluorescent fixtures
■
allows easy access to the router’s power and cable connections
Before Installing the Router
■
Read the safety information “Safety” on page 41.
■
Unpack the router. Verify the package contents. If any items are damaged or
missing, contact your sales representative.
613-000313 Rev B
Installation and Safety Guide
15
Installing an Optional PIC
If you purchased an optional PIC, install it now by following the Port Interface Card
Quick Install Guide. The PIC Quick Install Guide can be found with the PIC, on the
Documentation and Tools CD-ROM, or can be downloaded from
www.alliedtelesyn.com/support/software/.
Installing the Router in a Rack
1. Gather additional items. You will need:
•
the rack-mount kit (in your router package, or ordered from your authorised
distributor or reseller)
•
a Phillips #1 screwdriver
•
screws and cage nuts to attach the brackets to your rack
2. Check the rack.
Ensure that the rack is safely secured and that it will not tip over. Devices in a
rack should be installed starting at the bottom, with the heavier devices near the
bottom of the rack.
Ensure the rack has sufficient space for the router and its associated cables. The
router is 1U high.
3. Unscrew the feet from the router.
4. Connect the handles to the brackets.
Screw the handles to the wider side of each bracket, using the supplied screws
(see figure below).
5. Connect the brackets to the router.
Screw the brackets to the sides of the router, using the supplied screws (see
figure below). The router can be front or rear mounted.
6. Mount the router in the rack.
Use appropriate rack mounting screws (not supplied).
613-000313 Rev B
16
AR400 Series Router
Installing the Router on a Wall
You can install the router on a firm wall.
1. Gather additional items. You will need:
•
a wall mount bracket kit (ordered from your authorised distributor or
reseller)
•
a Phillips #1 screwdriver
•
a Phillips #2 screwdriver
•
If you are fixing the router to a solid masonry or hollow wall, you need
equipment to drill a 6 mm hole. The wall mount brackets are supplied with
screws and plugs to fasten the brackets to a masonry or plasterboard wall. If
you are fixing it to a wooden wall, the screws are self-tapping.
2. Screw the brackets to the router.
Screw a wall mount bracket to the outer screw holes on each side of the router
using the shorter M3 screws supplied.
Screw the wall brackets to the wall with the brackets at the top and bottom and
the feet against the wall.
Applying Power to the Router
1. Check the supply voltage and the router’s rated voltage.
AR400 Series routers are fitted with a universal mains power supply that will
function over the range 100-240 VAC and 50–60Hz.
For continued protection against the risk of fire and shock hazard, replace fuses
only with the same type and rating.
Warning The specific power supply requirements for a particular model are
clearly displayed on the rear or underside of the router. If the supply is outside
the accepted range for the router, the router may not operate or damage to
the router may result.
2. Fit the power cord retaining clip to the AC power inlet on the router’s rear panel.
613-000313 Rev B
Installation and Safety Guide
17
3. Connect the provided power cord to the AC power inlet and clip it in place.
Switch the router’s power switch to the ON position. The Power LED lights
continuously and the System LED lights briefly. The Port LEDs also light briefly.
The router is supplied with an approved power cord that incorporates a
moulded plug. It must only be used with the power cord supplied.
If the LEDs fail to light, the most likely cause is that the router is not receiving
power. Check that:
■
the power supply outlet’s switch (if any), and the router’s power switch, are in
the ON position
■
the power cable is securely plugged in
■
the power supply is operational
613-000313 Rev B
18
AR400 Series Router
Configuring the AR415S
By default, the DHCP server on the router is enabled, and all the switch ports
belong to the default VLAN (vlan1), which has an IP address of 192.168.1.1 (“Default
Configuration on AR415S, AR440S, AR441S, AR442S” on page 37).
We recommend starting to configure the router using the graphical user interface
(GUI), with its easy wizards. If necessary, you can then use the Command line
interface (CLI) to complete your configuration.
■
“Using the GUI to configure the AR415S” below
■
“Using the CLI to configure the AR415S” on page 21
Using the GUI to configure the AR415S
This section describes how to access the GUI via a switch port in the default VLAN
(vlan1) on the AR415S router, when the PC and the router are in the same subnet,
in order to configure the router.
Caution Only one DHCP server should usually be enabled on a network. If
you have an existing DHCP server, we recommend disabling either it or the
router’s DHCP server. To disable the router’s DHCP server, use the command
line to enter the command:
disable dhcp
If another device on your network already uses the router’s default IP address,
do not connect the router to the network until you have changed the IP
address of the router’s default VLAN (vlan1). Using the command line, enter
the command:
set ip interface=vlan1 ip=ipaddress mask=mask
See the Internet Protocol (IP) chapter in the Software Reference.
The GUI requires a PC running a web browser. Supported browsers are Internet
Explorer 5.0 or later and Netscape 6.2.2 or later, with JavaScript enabled. If you are
using a toolbar or plug-in on your browser to block pop-ups, disable it while using
the GUI. The GUI displays detailed configuration options and information in pop-up
windows.
613-000313 Rev B
Installation and Safety Guide
19
1. Connect the PC to a router switch port.
The PC can be connected directly, or through your LAN.
To connect the PC directly to the router, use a straight-through Ethernet cable
to connect an Ethernet card on the PC to any one of the router’s switch ports.
See the following figure.
straight-through cable
router
ON
SWITCH PORTS
POWER
4
2
3
1
PIC BAY
OFF
POWER
100-240 VAC
50/60 Hz
2.1 A
ETH0
ASYN0
switch ports
PC
To connect via a LAN, use an Ethernet cable to connect the router’s switch
port(s) to the device(s) on the LAN. Select the LAN PC from which you wish to
configure the router. The PC should be in the same subnet as the part of the
LAN that contains the router. For example, the PC could be connected to a hub
or Layer 2 switch that is directly connected to one of the router’s switch ports.
See the following figure.
ON
SWITCH PORTS
POWER
4
2
3
1
ON
10BASE-T/100BASE-TX SWITCH PORTS
4
3
2
OFF
OFF
POWER
PC
PIC BAY
1
POWER
100-240 VAC
50/60 Hz
2.1 A
hub or layer 2
switch
ETH0
ASYN0
switch ports
router
2. Set PC to automatic IP address.
Set the PC to accept an IP address assigned to it by the router’s DHCP server.
In Windows XP:
From the Start menu, select Control Panel > Network and Internet
Connections > Network Connections. Select the connection, right-click and
select Properties. In the connection Properties dialog box General tab, select
Internet Protocol (TCP/IP), and click Properties. In the General tab, select
Obtain an IP address automatically and Obtain a DNS server address
automatically. Close all the dialog boxes you opened.
In Windows 2000:
From the Start menu, select Settings > Network and Dial-up Connections. In
the Network and Dial-up Connections window, right click on the connection
and select Properties. In the list of components, select Internet Protocol (TCP/
613-000313 Rev B
20
AR400 Series Router
IP), and click Properties. In the Internet Protocol Properties dialog box, select
Obtain an IP address automatically and Obtain a DNS server address
automatically. Close all the dialog boxes you opened.
If these new IP address settings do not take effect immediately, you may need to
restart the PC.
If you have disabled the router’s DHCP server, assign the PC an IP address in the
same subnet as the router. The router’s default IP address is 192.168.1.1.
3. Browse to the GUI.
If you access the Internet through a proxy server, set your browser to bypass
the proxy for 192.168.1.1. Point your web browser to http://192.168.1.1.
4. Log in.
At the log in prompt, enter the user name and password. Passwords are case
sensitive. By default:
User Name: manager
Password: friend
If this is the first time the router is configured, the Configuration Wizards page
appears. Otherwise, you can open it using the Wizards menu option.
5. Configure the router.
You can configure the router using the GUI wizards or menu.
Important To ensure configuration settings are saved correctly, use the GUI
menus and buttons to navigate, not your browser’s buttons.
Caution As a security precaution, change the password as soon as
possible. Remember the new password, as there is no way to retrieve it if
it is lost.
Use the wizard and other configuration menu options to configure the
router. To change the ‘manager’ password, follow the basic setup wizard,
or select Management > Users from the sidebar menu. Select the
‘manager’ user name and click Modify.
To access context-sensitive help in the GUI, click on the Help button [Help].
The Help button is located at the top of the sidebar menu or on any popup
page. For more information about the GUI, see the Using the Graphical User
Interface (GUI) chapter in the Software Reference.
613-000313 Rev B
Installation and Safety Guide
21
6. Save the configuration.
The first time you start the router, it uses the default configuration in the file
boot.cfg.
Save your configuration to a new file, and set the router to use this file when it
restarts. We strongly recommend leaving the boot.cfg file unchanged, in case you
need to revert to the original default configuration. Some wizards save the
configuration automatically. If your configuration is not saved yet, the Save
button is red.
7. Advanced configuration.
If necessary, use the command line to complete the configuration if necessary
(“Using the CLI to configure the AR415S” below). Use the commands in the
Software Reference.
Using the CLI to configure the AR415S
This section describes how to access the CLI via a switch port in VLAN1 on the
AR415S routers, when the PC and the router are in the same subnet, in order to
configure the router.
Caution Only one DHCP server should usually be enabled on a network. If
you have an existing DHCP server, we recommend disabling either it or the
router’s DHCP server. To disable the router’s DHCP server, use the
command:
disable dhcp
If another device on your network already uses the router’s default IP address,
do not connect the router to the network until you have changed the IP
address of the router’s default VLAN. Using the command line, enter the
command:
set ip interface=vlan1 ip=ipaddress mask=mask
See the Internet Protocol (IP) chapter in the Software Reference.
1. Initiate router start-up.
Using the terminal cable supplied, connect a VT100-compatible terminal, or the
COM port of a PC running a terminal emulation program such as Windows
Hyper Terminal, to the Console RS-232 (ASYN0) port on the router’s rear
panel.
613-000313 Rev B
22
AR400 Series Router
Set the communication parameters on your terminal or terminal emulation
program to:
•
Baud rate: 9600
•
Data bits: 8
•
Parity: None
•
Stop bits: 1
•
Flow control: Hardware
See the AR400 Series Router Hardware Reference for more information on
configuring emulation software.
2. Log in and set the password.
The login prompt appears on the terminal or PC. If the login prompt does not
appear, press [Enter] two or three times.
When the router boots for the first time it automatically creates an account
with manager privileges. The account has the login name “manager” and the
password is “friend”. Passwords are case sensitive.
At the log in prompt, enter the login name and password.
Login: manager
Password: friend
The router’s command prompt appears and you can now configure the router
using the command line interface.
Warning Change the password as soon as possible. Leaving the manager
account with the default password is a serious security risk. Make sure you
remember the new password as there is no way to retrieve it if it is lost.
Use the following command to change the account password:
set password
3. Configure the router.
See the AR400 Series Router Software Reference for more information on router
start-up and configuration procedures (including a list of message definitions). To
continue configuring the router using the CLI, use the commands in the
Software Reference.
To display a list of help topics, enter:
help
613-000313 Rev B
Installation and Safety Guide
23
To display help on a specific topic, enter:
help topic
Alternatively, type a question mark (?) at the end of a partially completed
command to see a list of valid options.
4. Save the configuration.
Save your configuration to a new file, using the command:
create config=filename.cfg
and set the router to load this file when it restarts, using the command:
set config=filename.cfg
We recommend leaving the boot.cfg file unchanged, in case you need to revert
to the original default configuration.
Connecting Data Cables to AR415S
Connecting the router to your network:
1. Connect to the LAN
If you have not already done so, use straight-through Ethernet patch cables to
connect the device(s) on your private network (LAN) to the router’s switch
port(s). By default, all switch ports are members of VLAN1.
2. Connect to the WAN.
Caution If you intend to use a firewall, configure it before you activate
the WAN link.
Once initial configuration is complete, connect the router to the WAN:
•
Connect a PIC port to a WAN connection. See the Port Interface Card Quick
Install Guide and Hardware Reference.
•
Use an Ethernet patch cable to connect the router’s Ethernet WAN (ETH0)
port to the Ethernet port of a WAN device (such as a modem).
613-000313 Rev B
24
AR400 Series Router
System LEDs on AR415S
The LEDs described in the following table show the operational status and port
activity for the AR415S router.
LED
State
Function
PWR
Green
The router is receiving power and the power
switch is ON.
SYS
Amber
Lit briefly during router start up, or the router is
malfunctioning.
Off
Normal operation.
Green
A port interface card (PIC) is correctly installed
and has been detected by the router.
Off
No PIC is installed, or the router has not
recognised the PIC.
Green
The link is in full-duplex mode.
Off
The link is in half-duplex mode.
Green
A link has been established.
Flashing
Data is being transmitted.
Off
There is no link.
Green
The link is at 100 Mbps speed.
Off
The link is at 10 Mbps speed.
PIC 0
Full
L/A
100M
613-000313 Rev B
Installation and Safety Guide
25
AR440S, AR441S, AR442S Routers
This section describes how to install the AR440S, AR441S and AR442S routers.
■
“Installing the AR440S, AR441S, AR442S” below
■
“Configuring the AR440S, AR441S, AR442S” on page 29
■
“Connecting Data Cables to AR440S, AR441S, AR442S” on page 35
■
“System LEDs on AR440S, AR441S, AR442S” on page 36
For corresponding information about installing an AR415S, see “AR415S Router” on
page 14.
For corresponding information about installing an AR410, AR410S or AR450S, see
“AR410, AR410S, AR450S Routers” on page 6.
Installing the AR440S, AR441S, AR442S
Selecting a Site
You can install the router:
■
on a level surface such as a desktop or bench
■
in a standard 19-inch rack, using the rack-mount kit supplied with the router
■
on a firm wall, using a wall-mount kit ordered from your authorised distributor
or reseller
When you install the router, choose a site that:
■
allows adequate airflow around the router and its vents
■
is free of dust and moisture
■
AR440S, AR441S, AR442S: will maintain an ambient temperature in the range
0º C to 50º C (32º F to 122º F)
■
will maintain a humidity in the range 5% to 80% non-condensing
■
has a reliable and earthed (grounded) power supply, preferably dedicated and
filtered
■
does not expose cabling to sources of electrical noise such as radio transmitters,
broadband amplifiers, power lines, electric motors, and fluorescent fixtures
■
allows easy access to the router’s power and cable connections
Before Installing the Router
■
Read the safety information “Safety” on page 41.
■
Unpack the router. Verify the package contents. If any items are damaged or
missing, contact your sales representative.
613-000313 Rev B
26
AR400 Series Router
Installing an Optional PIC
If you purchased an optional PIC, install it now by following the Port Interface Card
Quick Install Guide. The PIC Quick Install Guide can be found with the PIC, on the
Documentation and Tools CD-ROM, or can be downloaded from
www.alliedtelesyn.com/support/software/.
Installing the Router in a Rack
1. Gather additional items. You will need:
•
the rack-mount kit (in your router package, or ordered from your authorised
distributor or reseller)
•
a Phillips #1 screwdriver
•
screws and cage nuts to attach the brackets to your rack
2. Check the rack.
Ensure that the rack is safely secured and that it will not tip over. Devices in a
rack should be installed starting at the bottom, with the heavier devices near the
bottom of the rack.
Ensure the rack has sufficient space for the router and its associated cables. The
router is 1U high.
3. Unscrew the feet from the router.
4. Connect the handles to the brackets.
Screw the handles to the wider side of each bracket, using the supplied screws
(see figure below).
5. Connect the brackets to the router.
Screw the brackets to the sides of the router, using the supplied screws (see
figure below). The router can be front or rear mounted.
613-000313 Rev B
Installation and Safety Guide
27
6. Mount the router in the rack.
Use appropriate rack mounting screws (not supplied).
Installing the Router on a Wall
You can install the router on a firm wall.
1. Gather additional items. You will need:
•
a wall mount bracket kit (ordered from your authorised distributor or
reseller)
•
a Phillips #1 screwdriver
•
a Phillips #2 screwdriver
•
If you are fixing the router to a solid masonry or hollow wall, you need
equipment to drill a 6 mm hole. The wall mount brackets are supplied with
screws and plugs to fasten the brackets to a masonry or plasterboard wall. If
you are fixing it to a wooden wall, the screws are self-tapping.
2. Screw the brackets to the router.
Screw a wall mount bracket to the outer screw holes on each side of the router
using the shorter M3 screws supplied.
Screw the wall brackets to the wall with the brackets at the top and bottom and
the feet against the wall.
613-000313 Rev B
28
AR400 Series Router
Applying Power to the Router
1. Check the supply voltage and the router’s rated voltage.
AR400 Series routers are fitted with a universal mains power supply that will
function over the range 100-240 VAC and 50–60Hz.
For continued protection against the risk of fire and shock hazard, replace fuses
only with the same type and rating.
Warning The specific power supply requirements for a particular model are
clearly displayed on the rear or underside of the router. If the supply is outside
the accepted range for the router, the router may not operate or damage to
the router may result.
2. Fit the power cord retaining clip to the AC power inlet on the router’s rear panel.
3. Connect the provided power cord to the AC power inlet and clip it in place.
Switch the router’s power switch to the ON position. The Power LED lights
continuously and the System LED lights briefly. The Port LEDs also light briefly.
The router is supplied with an approved power cord that incorporates a
moulded plug. It must only be used with the power cord supplied.
If the LEDs fail to light, the most likely cause is that the router is not receiving
power. Check that:
■
the power supply outlet’s switch (if any), and the router’s power switch, are in
the ON position
■
the power cable is securely plugged in
■
the power supply is operational
613-000313 Rev B
Installation and Safety Guide
29
Configuring the AR440S, AR441S, AR442S
By default, the DHCP server on the router is enabled, and all the switch ports
belong to the default VLAN (vlan1), which has an IP address of 192.168.1.1 (“Default
Configuration on AR415S, AR440S, AR441S, AR442S” on page 37).
We recommend starting to configure the router using the graphical user interface
(GUI), with its easy wizards. If necessary, you can then use the Command line
interface (CLI) to complete your configuration.
■
“Using the GUI to configure the AR415S” below
■
“Using the CLI to configure the router” on page 33
Using the GUI to configure the router
This section describes how to access the GUI via a switch port in the default VLAN
(vlan1) on the AR415S, AR440S, AR441S and AR442S routers, when the PC and the
router are in the same subnet, in order to configure the router.
Caution Only one DHCP server should usually be enabled on a network. If
you have an existing DHCP server, we recommend disabling either it or the
router’s DHCP server. To disable the router’s DHCP server, use the command
line to enter the command:
disable dhcp
If another device on your network already uses the router’s default IP address,
do not connect the router to the network until you have changed the IP
address of the router’s default VLAN (vlan1). Using the command line, enter
the command:
set ip interface=vlan1 ip=ipaddress mask=mask
See the Internet Protocol (IP) chapter in the Software Reference.
The GUI requires a PC running a web browser. Supported browsers are Internet
Explorer 5.0 or later and Netscape 6.2.2 or later, with JavaScript enabled. If you are
using a toolbar or plug-in on your browser to block pop-ups, disable it while using
the GUI. The GUI displays detailed configuration options and information in pop-up
windows.
613-000313 Rev B
30
AR400 Series Router
1. Connect the PC to a router switch port.
The PC can be connected directly, or through your LAN.
To connect the PC directly to the router, use a straight-through Ethernet cable
to connect an Ethernet card on the PC to any one of the router’s switch ports.
See the following figure.
PC
Router
4
2
3
1
POWER
ON
100-240 VAC
50/60 Hz
2.1 A
OFF
PIC BAY
ADSL
5
ASYN0
Switch Ports
To connect via a LAN, use an Ethernet cable to connect the router’s switch
port(s) to the device(s) on the LAN. Select the LAN PC from which you wish to
configure the router. The PC should be in the same subnet as the part of the
LAN that contains the router. For example, the PC could be connected to a hub
or Layer 2 switch that is directly connected to one of the router’s switch ports.
See the following figure.
Hub or Layer 2 Switch
PC
ON
10BASE-T/100BASE-TX SWITCH PORTS
4
3
2
1
OFF
POWER
Router
4
2
3
1
POWER
ON
100-240 VAC
50/60 Hz
2.1 A
OFF
PIC BAY
ADSL
5
Switch Ports
613-000313 Rev B
ASYN0
Installation and Safety Guide
31
2. Set PC to automatic IP address.
Set the PC to accept an IP address assigned to it by the router’s DHCP server.
In Windows XP:
From the Start menu, select Control Panel > Network and Internet
Connections > Network Connections. Select the connection, right-click and
select Properties. In the connection Properties dialog box General tab, select
Internet Protocol (TCP/IP), and click Properties. In the General tab, select
Obtain an IP address automatically and Obtain a DNS server address
automatically. Close all the dialog boxes you opened.
In Windows 2000:
From the Start menu, select Settings > Network and Dial-up Connections. In
the Network and Dial-up Connections window, right click on the connection
and select Properties. In the list of components, select Internet Protocol (TCP/
IP), and click Properties. In the Internet Protocol Properties dialog box, select
Obtain an IP address automatically and Obtain a DNS server address
automatically. Close all the dialog boxes you opened.
If these new IP address settings do not take effect immediately, you may need to
restart the PC.
If you have disabled the router’s DHCP server, assign the PC an IP address in the
same subnet as the router. The router’s default IP address is 192.168.1.1.
3. Browse to the GUI.
If you access the Internet through a proxy server, set your browser to bypass
the proxy for 192.168.1.1. Point your web browser to http://192.168.1.1.
4. Log in.
At the log in prompt, enter the user name and password. Passwords are case
sensitive. By default:
User Name: manager
Password: friend
If this is the first time the router is configured, the Configuration Wizards page
appears. Otherwise, you can open it using the Wizards menu option.
613-000313 Rev B
32
AR400 Series Router
5. Configure the router.
You can configure the router using the GUI wizards or menu.
Important To ensure configuration settings are saved correctly, use the GUI
menus and buttons to navigate, not your browser’s buttons.
Caution As a security precaution, change the password as soon as
possible. Remember the new password, as there is no way to retrieve it if
it is lost.
Use the wizard and other configuration menu options to configure the
router. To change the ‘manager’ password, follow the basic setup wizard,
or select Management > Users from the sidebar menu. Select the
‘manager’ user name and click Modify.
To access context-sensitive help in the GUI, click on the Help button [Help].
The Help button is located at the top of the sidebar menu or on any popup
page. For more information about the GUI, see the Using the Graphical User
Interface (GUI) chapter in the Software Reference.
6. Save the configuration.
The first time you start the router, it uses the default configuration in the file
boot.cfg.
Save your configuration to a new file, and set the router to use this file when it
restarts. We strongly recommend leaving the boot.cfg file unchanged, in case you
need to revert to the original default configuration. Some wizards save the
configuration automatically. If your configuration is not saved yet, the Save
button is red.
7. Advanced configuration.
If necessary, use the command line to complete the configuration if necessary
(“Using the CLI to configure the router” on page 33). Use the commands in the
Software Reference.
613-000313 Rev B
Installation and Safety Guide
33
Using the CLI to configure the router
This section describes how to access the CLI via a switch port in VLAN1 on the
AR440S, AR441S and AR442S routers, when the PC and the router are in the same
subnet, in order to configure the router.
Caution Only one DHCP server should usually be enabled on a network. If
you have an existing DHCP server, we recommend disabling either it or the
router’s DHCP server. To disable the router’s DHCP server, use the
command:
disable dhcp
If another device on your network already uses the router’s default IP address,
do not connect the router to the network until you have changed the IP
address of the router’s default VLAN. Using the command line, enter the
command:
set ip interface=vlan1 ip=ipaddress mask=mask
See the Internet Protocol (IP) chapter in the Software Reference.
1. Initiate router start-up.
Using the terminal cable supplied, connect a VT100-compatible terminal, or the
COM port of a PC running a terminal emulation program such as Windows
Hyper Terminal, to the Console RS-232 (ASYN0) port on the router’s rear
panel.
Set the communication parameters on your terminal or terminal emulation
program to:
•
Baud rate: 9600
•
Data bits: 8
•
Parity: None
•
Stop bits: 1
•
Flow control: Hardware
See the AR400 Series Router Hardware Reference for more information on
configuring emulation software.
613-000313 Rev B
34
AR400 Series Router
2. Log in and set the password.
The login prompt appears on the terminal or PC. If the login prompt does not
appear, press [Enter] two or three times.
When the router boots for the first time it automatically creates an account
with manager privileges. The account has the login name “manager” and the
password is “friend”. Passwords are case sensitive.
At the log in prompt, enter the login name and password.
Login: manager
Password: friend
The router’s command prompt appears and you can now configure the router
using the command line interface.
Warning Change the password as soon as possible. Leaving the manager
account with the default password is a serious security risk. Make sure you
remember the new password as there is no way to retrieve it if it is lost.
Use the following command to change the account password:
set password
3. Configure the router.
See the AR400 Series Router Software Reference for more information on router
start-up and configuration procedures (including a list of message definitions). To
continue configuring the router using the CLI, use the commands in the
Software Reference.
To display a list of help topics, enter:
help
To display help on a specific topic, enter:
help topic
Alternatively, type a question mark (?) at the end of a partially completed
command to see a list of valid options.
4. Save the configuration.
Save your configuration to a new file, using the command:
create config=filename.cfg
and set the router to load this file when it restarts, using the command:
set config=filename.cfg
We recommend leaving the boot.cfg file unchanged, in case you need to revert
to the original default configuration.
613-000313 Rev B
Installation and Safety Guide
35
Connecting Data Cables to AR440S, AR441S, AR442S
Connecting the router to your network:
1. Connect to the LAN
If you have not already done so, use straight-through Ethernet patch cables to
connect the device(s) on your private network (LAN) to the router’s switch
port(s). By default, all switch ports are members of VLAN1.
2. Connect to the WAN.
Caution If you intend to use a firewall, configure it before you activate
the WAN link.
Once initial configuration is complete, connect the router to the WAN:
•
AR440S, AR441S, AR442S: Connect a PIC port to a WAN connection. See
the Port Interface Card Quick Install Guide and Hardware Reference.
•
AR440S, AR441S: Using the DSL cable, connect the ADSL port to an ADSL
splitter that is connected to a digital subscriber line.
•
AR442S: Using the DSL cable, connect the SHDSL port to the digital
subscriber line.
613-000313 Rev B
36
AR400 Series Router
System LEDs on AR440S, AR441S, AR442S
The LEDs described in the following table show the operational status and port
activity for the AR440S, AR441S and AR442S routers.
LED
State
Function
Power
Green
The router is receiving power and the power
switch is ON.
System
Red or amber
Lit briefly during router start up, or the router is
malfunctioning.
Flashing
The fan has failed.
Off
Normal operation.
Green
A port interface card (PIC) is correctly installed
and has been detected by the router.
Off
No PIC is installed, or the router has not
recognised the PIC.
1-5
Green
A 100 Mbps link has been established.
(switch
ports)
Green flashing
Data is being transmitted at 100 Mbps.
Amber
A 10 Mbps link has been established.
Amber flashing
Data is being transmitted at 10 Mbps.
Off
No link is present.
Green
A link has been established, and is ready to send
or receive data.
Green flashing fast
Data is being transmitted or received.
PIC
ADSL/
SHDSL
Green flashing slow (1 The port is in Loopback mode.
sec)
613-000313 Rev B
Amber
ADSL or SHDSL is enabled and is looking for DSL
handshake tones (in the Handshake State).
Amber flashing
The port is training.
Green & amber
alternate
There is a fault in the port.
Off
The port is disabled.
Installation and Safety Guide
37
Default Configuration on AR415S, AR440S,
AR441S, AR442S
The default configuration file boot.cfg loads automatically when the router starts up.
This file is stored in the router’s flash memory. The AR415S, AR440S, AR441S and
AR442S have the following default configuration:
#Default configuration file boot.cfg
# Set the command help file. (You may have a different help file.)
set help=54-275a.HLP
# Enable IP and assign an IP address to the default VLAN.
enable ip
add ip interface=vlan1 ip=192.168.1.1
# Enable the DHCP server, configure a range and a 3 day
# lease policy, and assign the router as a DNS server.
enable dhcp
create dhcp policy=lan-dhcp lease=259200
add dhcp policy=lan-dhcp subnet=255.255.255.0
add dhcp policy=lan-dhcp router=192.168.1.1
add dhcp policy=lan-dhcp dnsserver=192.168.1.1
cre dhcp range=standard poli=lan-dhcp ip=192.168.1.100 number=50
# Enable DNS relay, so that DNS will work for DHCP clients.
enable ip dnsrelay
The AR410, AR410S, AR450S boot.cfg files have no significant default configuration.
613-000313 Rev B
38
AR400 Series Router
Documentation and Tools CD-ROM
The Documentation and Tools CD-ROM bundled with each router contains the
complete Document Set for your router. The CD-ROM also includes tools for
managing your router.
The Document Set on the CD-ROM includes:
■
this Installation and Safety Guide
■
the AR400 Series Router Hardware Reference, which provides detailed information
on the hardware features of AR400 Series routers
■
the AR400 Series Router Software Reference, which provides detailed information
on configuring the router and its software
■
the Port Interface Card Quick Install Guide, which provides instructions for
installing a Port Interface Card in your router
■
the Port Interface Card Hardware Reference, which provides detailed information
on the hardware features of Port Interface Cards
■
AT-TFTP Server for Windows, for downloading software releases
■
Adobe Acrobat Reader, for viewing online documentation
Updates of these documents can also be downloaded from the AR400 Series Router
Support Site from www.alliedtelesyn.com/support/software/.
613-000313 Rev B
Installation and Safety Guide
39
Connection to mains voltage supply
This router is supplied with a power cord has been approved for use and
incorporates a moulded plug. It must only be used with the power cord supplied.
For continued protection against the risk of fire and shock hazard, replace fuses only
with the same type and rating.
Telecommunications Interfaces
Warning To reduce risk of fire, use only No.26 awg (0.4 mm) or larger
telecommunications line cord if the cord supplied is not used with the
apparatus.
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons, including the
following:
1. Do not use this product near water, for example near a bathtub, washbowl,
kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak while in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose
of batteries in a fire: they may explode. Check with local codes for possible special
disposal instructions.
5. Remove the telephone cord from the unit prior to making changes to the
expansion port.
Save these instructions
613-000313 Rev B
40
AR400 Series Router
Connection to ISDN network
This product is supplied with an approved patch cord for connection to the ISDN
Basic Rate Network.
Ports for the connection of other apparatus
The following interfaces normally operate at Safe Extra Low Voltage (SELV) levels:
■
asynchronous (console) ports
■
Ethernet ports
■
G703 ports
■
synchronous ports
Note SELV is a secondary circuit whose voltages do not exceed a safe value under
normal operating conditions and under single fault conditions. Under normal
operating conditions the voltages do not exceed 42.4V peak a.c. or 60V d.c.
TNV1
The following interfaces are Telecommunications Network Voltage (TNV1) circuits,
which operate normally within the limits of SELV:
■
BRI ports for connection to ISDN Basic Rate telecommunications networks
■
PRI ports for connection to ISDN Primary Rate telecommunications networks
■
E1/T1 ports for connection to E1/T1 services
Note A TNV1 circuit is a circuit which under normal operating conditions does not
exceed the limits for SELV and on which overvoltages from telecommunication
networks are possible.
TNV3
The following interface is a Telecommunications Network Voltage (TNV3) circuit,
which operates normally in excess of the limits of SELV:
■
xDSL ports for connection to xDSL services
Note A TNV3 circuit is a circuit which under normal operating conditions exceed
the limits for SELV and on which overvoltages from telecommunication networks are
possible.
613-000313 Rev B
Installation and Safety Guide
41
Safety
WARNING: In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
ELECTRICAL NOTICES
WARNING: ELECTRIC SHOCK HAZARD
To prevent ELECTRIC shock, do not remove the cover. No user-serviceable parts
inside. This unit contains HAZARDOUS VOLTAGES and should only be opened by a
trained and qualified technician.
LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during periods of
LIGHTNING ACTIVITY.
CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO
DE-ENERGIZE EQUIPMENT, disconnect the power cord.
ELECTRICAL - TYPE CLASS 1 EQUIPMENT
THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a
properly wired earth ground socket outlet. An improperly wired socket outlet could
place hazardous validates on accessible metal parts.
PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the equipment
and shall be easily accessible.
CAUTION: Air vents must not be blocked and must have free access to the room
ambient air for cooling.
OPERATING TEMPERATURE: AR410, AR410S, AR415S, AR450S: This
product is designed for a maximum ambient temperature of 40° degrees C.
AR440S, AR441S, AR442S: This product is designed for a maximum ambient
temperature of 50° degrees C.
ALL COUNTRIES: Install product in accordance with local and National
Electrical Codes.
ELECTRICAL - AC MAINS CIRCUIT OVERLOADING
When installing product, consideration must be given to the accumulative nameplate
ratings when connecting the equipment to the AC supply wiring.
Lithium Battery - Should only be changed by authorised service personnel.
CAUTION: Danger of explosion if battery incorrectly replaced. Replace only with
Lithium Battery, type CR2032, and dispose of in accordance with the manufacturer’s
recommendations and all local codes.
613-000313 Rev B
42
AR400 Series Router
Sicherheit
WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen
hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen
ergreifen.
ACHTUNG: GEFÄHRLICHE SPANNUNG
Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile.
Das Gerät steht unter Hochspannung und darf nur von qualifiziertem technischem
Personal geöffnet werden.
GEFAHR DURCH BLITZSCHLAG
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters
ausführen.
VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DER
STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DER
STECKDOSE ZIEHEN.
GERÄTE DER KLASSE 1
DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer
vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger
Anschluß kann die Metallteile des Gehauses unter gefährliche elektrische
Spannungen setzen.
STECKBARES GERÄT: Die Anschlußbuchse sollte in der Nähe der Einrichtung
angebracht werden und leicht zugänglich sein.
VORSICHT
Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien
Zugang zur Raumluft haben.
BETRIEBSTEMPERATUR: AR410, AR410S, AR415S, AR450S: Dieses Produkt
wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als 40° C
entworfen. AR440S, AR441S, AR442S: Dieses Produkt wurde für den Betrieb in
einer Umgebungstemperatur von nicht mehr als 50° C entworfen.
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen
Vorschriften entsprechen.
NETZSICHERUNG
Bei der Installation muß der auf dem Typenschild angezeigte Nennwert des Gerätes
für den Anschluß an das Netz beachtet werden.
Lithium-Batterie - Sollte nur von einem geschulten qualifizierten Techniker
ausgetauscht werden.
VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Nur
mit einer gleichen Batterie oder einem gleichwertigen Batterietyp nach Empfehlung
des Herstellers ersetzen. Gebrauchte Batterien nach Anweisungen des Herstellers
beseitigen.
Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste Schalldruckpegel
beträgt 70dB(A) oder weniger gemäss EN ISO 7779.
613-000313 Rev B
Installation and Safety Guide
43
Sikkerhed
ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.
Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige
foranstaltninger.
ELEKTRISKE FORHOLDSREGLER
ADVARSEL: RISIKO FOR ELEKTRISK STØD
For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele,
der kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE
STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker.
FARE UNDER UVEJR
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med
LYNAKTIVITET.
ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE
STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen ud
af stikket.
ELEKTRISK - KLASSE 1-UDSTYR
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med
en korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret stikkontakt
kan sætte livsfarlig spænding til tilgængelige metaldele.
UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og skal
være lettilgængelig.
ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den
omgivende luft i rummet for afkøling.
BETJENINGSTEMPERATUR: AR410, AR410S, AR415S, AR450S: Dette apparat
er konstrueret til en omgivende temperatur på maksimum 40 grader C.
AR440S, AR441S, AR442S: Dette apparat er konstrueret til en omgivende
temperatur på maksimum 50 grader C.
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og
national lovgivning for elektriske installationer.
ELEKTRISK-OVERBELASTNING AF SPÆNDINGSKREDSLØBET
Ved installation af produktet, bør der tages hensyn til den kumulative kapacitet der
angives på navneskiltet, når udstyret forbindes med vekselstrømsledningen.
Lithium batteri - Bør kun udskiftes af uddannet og kvalificeret tekniker.
ADVARSEL : Eksplosionsfare, hvis batteriet udskiftes ukorrekt. Udskift kun med
samme eller en tilsvarende type der anbefales af producenten. Kassér brugte
batterier i overensstemmelse med producentens instruktioner.
613-000313 Rev B
44
AR400 Series Router
Veiligheid
WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in
welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.
WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT
WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN
Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen.
Binnenin bevinden zich geen onderdelen die door de gebruiker onderhouden
kunnen worden. Dit toestel staat onder GEVAARLIJKE SPANNING en mag alleen
worden geopend door een daartoe opgeleide en bevoegde technicus.
GEVAAR VOOR BLIKSEMINSLAG
GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.
WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE
STROOMKABEL TE ONTKOPPELEN.OM HET TOESTEL STROOMLOOS TE
MAKEN: de stroomkabel ontkoppelen.
ELEKTRISCHE TOESTELLEN VAN KLASSE 1
DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn op
een juist geaarde contactdoos. Een onjuist geaarde contactdoos kan de metalen
onderdelen waarmee de gebruiker eventueel in aanraking komt onder gevaarlijke
spanning stellen.
AAN TE SLUITEN APPARATUUR, de contactdoos wordt in de nabijheid van de
apparatuur geïnstalleerd en is gemakkelijk te bereiken.
OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de
omgevingslucht ongehinderd toelaten voor afkoeling.
BEDRIJFSTEMPERATUUR: AR410, AR410S, AR415S, AR450S: De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden Celsius.
AR440S, AR441S, AR442S: De omgevingstemperatuur voor dit produkt mag niet
meer bedragen dan 50 graden Celsius.
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale
elektrische voorschriften.
ELEKTRISCH: OVERBELASTING VAN WISSELSTROOM HOOFDCIRCUIT
Tijdens de installatie van het produkt dient men rekening te houden met de
gecombineerde waarden op de naamplaatjes bij het aansluiten van het toestel op de
wisselstroom-voedingsdraden.
Lithium batterij. Mag alleen worden vervangen door een daartoe opgeleide en
bevoegde technicus.
OPGELET: Gevaar voor ontploffing indien de batterij verkeerd wordt vergangen.
Alleen vervangen door hetzelfde of een gelijkwaardig, door de fabrikant aanbevolen
type.
613-000313 Rev B
Installation and Safety Guide
45
Sécurité
MISE EN GARDE : dans un environnement domestique, ce produit peut
provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre
les mesures adéquates.
INFORMATION SUR LES RISQUES ÉLECTRIQUES
AVERTISSEMENT: DANGER D’ÉLECTROCUTION
Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du
matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur. Il
comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un
technicien dûment qualifié.
DANGER DE FOUDRE
DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.
ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS CIRCUIT.
POUR COUPER L’ALIMENTATION DU MATÉRIEL, débrancher le cordon.
ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE
CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être branchée
dans une prise femelle correctement mise à la terre car des tensions dangereuses
risqueraient d’atteindre les pièces métalliques accessibles à l’utilisateur.
EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit être
placée près de l’équipement et facilement accessible”.
ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant
de circuler librement pour le refroidissement.
TEMPÉRATURE DE FONCTIONNEMENT: AR410, AR410S, AR415S,
AR450S: Ce matériel est capable de tolérer une température ambiante maximum de
ou 40 degrés Celsius.
AR440S, AR441S, AR442S: Ce matériel est capable de tolérer une température
ambiante maximum de ou 50 degrés Celsius.
POUR TOUS PAYS: Installer le matériel conformément aux normes électriques
nationales et locales.
SURCHARGE DES CIRCUITS PRINCIPAUX DE COURANT ALTERNATIF
ÉLECTRIQUE
Lors de l'installation du matériel, il faut prendre en compte la somme des puissances
indiquées sur les étiquettes au moment de connecter le matériel à une source de
courant alternatif.
Pile en Lithium-Doit uniquement être remplacée par un technicien dûment qualifié
ATTENTION : Un danger d'explosion existe en cas de remplacement incorrect de
la pile. Remplacer uniquement avec une pile du même type ou d'un type
recommandé par le fabricant. Mettre au rebut lespiles usagées conformément aux
instructions du fabricant).
613-000313 Rev B
46
AR400 Series Router
Turvallisuus
VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin
toimenpiteisiin.
SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA
VAROITUS: SÄHKÖISKUVAARA
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa
olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain
koulutettu ja pätevä teknikko.
SALAMANISKUVAARA
HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA
SALAMOINNIN AIKANA.
HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA.
VIRTA KATKAISTAAN irrottamalla virtajohto.
SÄHKÖ - TYYPPILUOKAN 1 LAITTEET
TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti
maadoitettuun pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa
metalliosat vaarallisille jännitteille.
PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle ja
siihen on oltava esteetön pääsy.
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys
ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.
KÄYTTÖLÄMPÖTILA: AR410, AR410S, AR415S, AR450S: Tämä tuote on
suunniteltu ympäröivän ilman maksimilämpötilalle 40°C.
AR440S, AR441S, AR442S: Tämä tuote on suunniteltu ympäröivän ilman
maksimilämpötilalle 50°C.
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten
sähköturvallisuusmääräysten mukaisesti.
SÄHKÖ-VAIHTORVIRTASÄHKÖPIIRIN YLIKUORMITUS
Tuotetta asennettaessa on otettava huomioon osien nimikilvissä osoitettu teho
silloin kun osat liitetetään vaihtovirtaverkkoon.
Litiumparisto - Vaihdon voi suorittaa vain koulutettu ja pätevä teknikko.
Varoitus: Räjähdysvaara, jos paristo on vaihdettu väärin. Vaihda vain samaan tai
vastaavaan tyyppiin, jota valmistaja suosittelee. Hävitä käytetyt paristot valmistajan
ohjeiden mukaan.
613-000313 Rev B
Installation and Safety Guide
47
Norme di Sicurezza
AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio
interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati
provvedimenti.
AVVERTENZE ELETTRICHE
ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE
Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti
interne non sono riparabili dall’utente. Questa unità ha TENSIONI PERICOLOSE e
va aperta solamente da un tecnico specializzato e qualificato.
PERICOLO DI FULMINI
PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante
PRECIPITAZIONI TEMPORALESCHE.
ATTENZIONE: IL CAVO DI ALIMENTAZIONE È USATO COME DISPOSITIVO
DI DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL DISPOSITIVO staccare
il cavo di alimentazione.
ELETTRICITÀ - DISPOSITIVI DI CLASSE 1
QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve essere
inserita in una presa di corrente specificamente dotata di messa a terra. Una presa
non cablata in maniera corretta rischia di scaricare una tensione pericolosa su parti
metalliche accessibili.
APPARECCHIATURA COLLEGABILE, la presa va installata vicino all’apparecchio
per risultare facilmente accessibile.
ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero
ricircolo dell’aria ambiente per il raffreddamento.
TEMPERATURA DI FUNZIONAMENTO: AR410, AR410S, AR415S, AR450S:
Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi
centigradi.
AR440S, AR441S, AR442S: Questo prodotto è concepito per una temperatura
ambientale massima di 50 gradi centigradi.
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative
elettriche nazionali.
ELETTRICITÀ - SOVRACCARICO DEL CIRCUITO DI RETE A C.A.
Durante l'installazione ed il collegamento del dispositivo alla rete di alimentazione a
corrente alternata, è necessario tenere in considerazione le capacità cumulative
riportate sulla targhetta.
Batteria al litio - Va sostituita solo da un tecnico specializzato e qualificato.
ATTENZIONE: l'errata sostituzione della batteria può causare pericolo di
esplosioni. Sostituire solamente con lo stesso tipo o con uno equivalente
raccomandato dal produttore. Eliminare le batterie usate secondo le istruzioni del
produttore.
613-000313 Rev B
48
AR400 Series Router
Sikkerhet
ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.
ELEKTRISITET
ADVARSEL: FARE FOR ELEKTRISK SJOKK
For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som
brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE
SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker.
FARE FOR LYNNEDSLAG
FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET. FOR
Å DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.
ELEKTRISK - TYPE 1- KLASSE UTSTYR
DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt
jordet kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig spenninger i
lett t ilgjengelige metalldeler.
UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av utstyret
og skal være lett tilgjengelig.
FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med
romtemperatur for avkjøling.
DRIFTSTEMPERATUR: AR410, AR410S, AR415S, AR450S: Dette produktet er
konstruert for bruk i maksimum romtemperatur på 40 grader celsius.
AR440S, AR441S, AR442S: Dette produktet er konstruert for bruk i maksimum
romtemperatur på 50 grader celsius.
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale
elektriske koder.
ELEKTRISK OVERBELASTNING PÅ AC HOVEDKRETSLØP
Når produktet installeres, må de samlede navneplateverdiene kontrolleres nøye når
strøm påsettes.
Litiumbatteri — Må kun byttes ut av en faglig kvalifisert tekniker.
FORSIKTIG: Eksplosjonsfare hvis batteriet feilinnsettes.Batteriet må bare erstattes
med samme type eller en tilsvarende type som er anbefalt av fabrikanten. Batteriene
må kasseres i samsvar med fabrikantens instruksjoner.
613-000313 Rev B
Installation and Safety Guide
49
Segurança
AVISO: Num ambiente doméstico este produto pode causar interferência na
radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas
adequadas.
AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS
ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO
Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que
possam ser consertadas pelo usuário. Este aparelho contém VOLTAGENS
PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado.
PERIGO DE CHOQUE CAUSADO POR RAIO
PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos
suscetíveis a QUEDAS DE RAIO.
CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM
DISPOSITIVO DE DESCONEXÃO. PARA DESELETRIFICAR O EQUIPAMENTO,
desconecte o cabo de ALIMENTAÇÃO.
ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1
DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O plugue
de alimentação deve ser conectado a uma tomada com adequada ligação de fio terra.
Tomadas sem adequada ligação de fio terra podem transmitir voltagens perigosas a
peças metálicas expostas.
EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto do
equipamento e ser de fácil acesso.”
CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter
acesso livre ao ar ambiente para arrefecimento adequado do aparelho.
TEMPERATURA DE FUNCIONAMENTO: AR410, AR410S, AR415S,
AR450S: Este produto foi projetado para uma temperatura ambiente máxima de 40
graus centígrados. AR440S, AR441S, AR442S: Este produto foi projetado para uma
temperatura ambiente máxima de 50 graus centígrados.
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e
locais para instalações elétricas.
ELÉTRICO - SOBRECARGA DA REDE DE CORRENTE ALTERNADA (AC)
Antes de instalar o produto, verifique o efeito cumulativo da conexão de diversos
aparelhos àrede de corrente alternada através das etiquetas que indicam potência ou
amperagem.
Bateria de lítio - Só deve ser trocada por técnico qualificado e treinado.
CUIDADO: Se a bateria não for devidamente instalada há perigo de explosão.
Substitua somente pelo mesmo tipo ou equivalente, conforme recomendado pelo
fabricante. Descarte baterias usadas, de acordo com as instruções fornecidas pelo
fabricante.
613-000313 Rev B
50
AR400 Series Router
Seguridad
ADVERTENCIA: en un entorno doméstico, este producto puede causar
radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las
medidas que sean convenientes al respecto.
AVISOS ELECTRICOS
ADVERTENCIA: PELIGRO DE ELECTROCHOQUE
Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en
el interior al cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES
PELIGROSOS y sólo deberá abrirla un técnico entrenado y calificado.
PELIGRO DE RAYOS
PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los
equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.
ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN
DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO, desconecte
el cable de alimentación.
ELECTRICO - EQUIPO DEL TIPO CLASE 1
ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que
conectarse a un enchufe a tierra debidamente instalado. Un enchufe que no está
correctamente instalado podría ocasionar tensiones peligrosas en las partes
metálicas que están expuestas.
EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en un
lugar con acceso fácil”.
ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán
tener acceso libre al aire ambiental de la sala para su enfriamiento.
TEMPERATURA REQUERIDA PARA LA OPERACIÓN:
AR410, AR410S, AR415S, AR450S: Este producto está diseñado para una
temperatura ambiental máxima de 40 grados C.
AR440S, AR441S, AR442S: Este producto está diseñado para una temperatura
ambiental máxima de 50 grados C.
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos
Eléctricos locales y nacionales.
ELECTRICO - SOBRECARGA DEL CIRCUITO PRIMARIO DE CORRIENTE
ALTERNA
Al instalarse el producto deberán considerarse las potencias nominales acumulativas,
cuando se conecta el equipo al cable de alimentación de corriente alterna.
Batería de litio - Sólo deberá ser cambiada por un técnico entrenado y calificado.
ATENCION: Peligro de explosión si la batería no se reemplaza en forma correcta.
Reemplace sólo con el mismo tipo o equivalente que recomienda el fabricante.
Deseche las baterías usadas según las instrucciones del fabricante.
613-000313 Rev B
Installation and Safety Guide
51
Säkerhet
VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan
tvinga användaren till att vidtaga erforderliga åtgärder.
TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:
RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket. Det
finns inga delar inuti som behöver underhållas. Denna apparat är under
HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker.
FARA FÖR BLIXTNEDSLAG
FARA: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.
VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA
FRÅN STRÖMMEN, dra ur nätkabeln.
ELEKTRISKT - TYP KLASS 1 UTRUSTNING
DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara ansluten till
ett ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande metalldelar
utsätts för högspänning. Apparaten skall anslutas till jordat uttag, när den ansluts till
ett nätverk.
UTRUSTNING MED PLUGG. Uttaget skall installeras i utrustningens närhet och
vara lättåtkomligt”.
VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande
rumsluft för avsvalning.
DRIFTSTEMPERATUR: AR410, AR410S, AR415S, AR450S: Denna produkt är
konstruerad för rumstemperatur ej överstigande 40 grader Celsius.
AR440S, AR441S, AR442S: Denna produkt är konstruerad för rumstemperatur ej
överstigande 50 grader Celsius.
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga
bestämmelser för elektrisk utrustning.
ELEKTRISKT - ÖVERBELASTNING AV VÄXELSTRÖMSNÄTET: När produkten
installeras bör den sammanlagda effekten på namnplåten beaktas när apparaten
ansluts till växelströmsnätet.
Litium batteri - Får endast bytas av utbildade och kvalificerade tekniker.
VARNING: Risk för explosion om felaktigt batteri används. Byt endast mot samma
eller likvärdig typ batteri, rekommenderat av tillverkaren. Kassera använda batterier
i enlighet med tillverkarens instruktioner.
613-000313 Rev B
52
AR400 Series Router
US Federal Communications Commission (FCC)
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the underside of this equipment is a label that contains,
among other information, a product identifier in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone company.
For the AR021U PIC
Facility Interface Code
021S5
Service Order Code
6.0Y
The AR021U PIC has completed the ISDN Ordering
Codes Translation Review and is registered for IOC
S and EZ-ISDN 1.
USOC Jack Type
RJ49C
For the AR440S and AR442S routers
USOC Jack Type
RJ11C
Should you experience trouble with this telephone equipment, please contact:
ALLIED TELESIS INC.
19800 NORTH CREEK PARKWAY #200
BOTHELL
WASHINGTON 98011
TEL: 425 487 8880
FAX: 425 489 9191
If trouble is experienced with this equipment (AR021U PIC, AR440S, AR442S), for
repair or warranty information, please contact the above. If the equipment is causing
harm to the telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
This equipment cannot be used on public coin phone service provided by the
telephone company. Connection to party line service is subject to state tariffs.
Your telephone company may discontinue your service if your equipment causes
harm to the telephone network. They will notify you in advance of disconnection, if
possible. During notification, you will be informed of your right to file a complaint to
the FCC.
Occasionally, your telephone company may make changes in its facilities, equipment,
operation, or procedures that could affect the operation of your equipment. If so,
you will be given advance notice of the change to give you an opportunity to
maintain uninterrupted service.
613-000313 Rev B
Installation and Safety Guide
53
Canadian Department of Communications
The Industry Canada label identifies certified equipment. This certification means
that the equipment meets telecommunications network protective, operational and
safety requirements as prescribed in the appropriate Terminal Equipment Technical
Requirements document(s). The Department does not guarantee the equipment will
operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated
by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections
of the power utility, telephone lines and internal metallic water pipe system, if
present, are connected together. This precaution may be particularly important in
rural areas.
Warning Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority, or electrician,
as appropriate.
This digital apparatus does not exceed the limits for radio noise emissions from
digital apparatus as set out in the Radio Interface Regulations of the Canadian
Department of Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les
limites applicables aux appareils numeriques prescrites dans le Reglement sur le
brouillage radioelectrique edicte par le ministere des Communications du Canada.
613-000313 Rev B
54
AR400 Series Router
Emission Compliance Statements
STANDARDS: The AR410, AR410S, AR415S, AR440S, AR441S, and AR442S meet the
following standards:
Category
Approval Agency and Requirement
Safety
UL60950-1
EN60950-1
AS/NZS 60950
Electromagnetic Compliance
FCC CFR47 Part 15 Class A
EN55022 Class A
VCCI Class A
AS/NZS CISPR22 Class A
Immunity
EN55024
Network Interface
(where applicable)
ISDN Limited Network Protocol Analysis
FCC Part 68, Subpart D
IC CS-03, Issue 8, Part I and IV
TBR3
TBR4
TR048
TIA-968-A
PTC 270
G.992.1 Annex A (AR440S only)
G.992.1 Annex B (AR441S only)
G.991.2 (AR442S only)
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved by the manufacturer or the FCC can void
your right to operate this equipment.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
613-000313 Rev B
Installation and Safety Guide
55
STANDARDS: The AR450S meets the following standards:
Category
Approval Agency and Requirement
Safety
UL60950
EN60950
AS/NZS 3260
Electromagnetic Compliance
FCC CFR47 Part 15 Class B
EN55022 Class B
VCCI Class B
AS/NZS CISPR22 Class B
Immunity
EN55024
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment uses, generates
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase separation between the equipment and the receiver.
• Connect equipment to an outlet on a circuit different from the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Modifications or changes not expressly approved by the manufacturer or the FCC can void
your right to operate this equipment.
Canadian Department of Communications
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
613-000313 Rev B
EC Declaration of Conformity
We:
ALLIED TELESIS LABS LIMITED
27 NAZARETH AVENUE
CHRISTCHURCH 8002
NEW ZEALAND
Declare under our sole legal responsibility that the following product meets the
safety, protection and conformity requirements of council directives 1999/5/EC,
89/336/EEC and 73/23/EEC, as amended by directive 93/68/EEC, on the
approximation of the laws of member states relating to electromagnetic
compatibility, electrical safety and the mutual recognition of conformity of
telecommunications terminal equipment.
AR400 SERIES ROUTERS
to which this declaration relates are in conformity with the following relevant
harmonized standards, the reference numbers of which have been published in the
Official journal of the European community.
EN55022: 1998
Information Technology Equipment—Radio disturbance
EN55024: 1998
Information Technology Equipment—Immunity
characteristics—Limits and methods of measurement.
EN60950: 2000
AR450S: Safety of Information Technology Equipment,
including electrical business equipment.
EN60950-1: 2001
AR410, AR410S, AR415S, AR440S, AR441S, AR442S:
Information Technology Equipment including electrical
business equipment—General Requirements.
Name: John Shields
On behalf of the Manufacturer
Signature:
Position:
Managing Director
Date: 9 March 2006