Samsung iPOLiS SNP-3120V User manual

NETWORK CAMERA
User Manual
SNP-3120/
3120V/3120VH
Network Camera
User Manual
Copyright
©2011 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the
problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
™ Design and specifications are subject to change without prior notice.
™ The default password can be exposed to a hacking thread so it is recommended to change the password
after installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible
for the user.
overview
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
● OVERVIEW
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety, If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
English _3
overview
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PROCUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.
4_ overview
When used outside of the U.S., it may be used HAR code with fittings of
an approved agency is employed.
CAUTION
The BNC Out terminal of the product is provided for easier installation, and is
not recommended for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage
or malfunction to the product.
Please use the input power with just one camera and other devices must not
be connected.
Do not expose the product to the direct airflow from an air conditioner.
Otherwise, it may cause moisture condensation inside the Clear Dome due to
temperature difference between internal and external of the dome camera.
If you install this product in a low-temp area such as inside a cold store, you
must seal up the wiring pipe with silicon, so that the external air can not flow
inside the housing.
Otherwise, external high, humid air may flow inside the housing, pooling
moisture or vapor inside the product due to a difference between internal and
external temperature.
English _5
● OVERVIEW
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
overview
Please read the following recommend safety precautions carefully.
Do not place this apparatus on an uneven surface.
Do not install on a surface where it is exposed to direct
sunlight, near heating equipment or heavy cold area.
Do not place this apparatus near conductive material.
Do not attempt to service this apparatus yourself.
Do not place a glass of water on the product.
Do not install near any magnetic sources.
Do not block any ventilation openings.
Do not place heavy items on the product.
User’s Manual is a guidance book how to use the products
The meaning of the using sign in the book is following
 Reference : In case of providing information for helping of product’s usages
 Notice : If there’s any possibility to occur any damages for the goods and
human caused by not following the instruction
 Please read this manual for the safety before using of goods and keep it in
the safe place.
6_ overview
Samsung Techwin cares for the environment at all product manufacturing stages, and is
taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly
products, and indicates that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection
systems)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other
household waste at the end of their working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate these items from other
types of waste and recycle them responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take these items for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with other
commercial wastes for disposal.
English _7
● OVERVIEW
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
overview
CONTENTS
OVERVIEW
3
3
10
10
10
11
13
INSTALLATION &
CONNECTION
18
18
28
32
34
37
41
42
43
NETWORK CONNECTION
AND SETUP
46
46
47
48
49
50
51
54
55
57
57
8_ overview
Important Safety Instructions
Product Features
Recomended PC Specifications
Recomended SDHC/SD Memory
Card Specifications
What’s Included
At a Glance
DIP Switch Setting
Installation (SNP-3120)
Installing with accessories (Sold
Separately)
Installation (SNP-3120V)
Installation (SNP-3120VH)
Inserting/Removing an SD
Memory Card
Memory Card Information
(Not Included)
Connecting with other Device
Connecting the Camera Directly
to Local Area Networking
Connecting the Camera Directly
to a DHCP Based DSL/Cable
Modem
Connecting the Camera Directly
to a PPPoE Modem
Connecting the Camera to an
IP Router with the PPPoE/Cable
Modem
Buttons used in IP Installer
Static IP Setup
Dynamic IP Setup
Port Range Forward (Port
Mapping) Setup
Connecting to the Camera from a
Shared Local PC
Connecting to the Camera from a
Remote PC via the Internet
WEB VIEWER
58
67
SETUP SCREEN
80
APPENDIX
104
Connecting to the Camera
Login
Installing Silverlight Runtime
Using the Live Screen
Playback
Playing the backup recordings
67
67
77
79
Using the Camera Menu
Camera Setting
OSD Setting
Initialize
80
80
88
93
99
Setup
Audio & Video Setup
Network Setup
Event Setup
System Setup
104
109
111
113
115
Specification
Product Overview
Troubleshooting
Open Source Announcement
GPL/LGPL Software License
English _9
● OVERVIEW
CAMERA SETUP
58
59
60
62
65
66
overview
PRODUCT FEATURES
 Multi-Streaming
This network camera can display videos in different resolutions and qualities simultaneously using different CODECs.
M
 However, MPEG4 video can not be played on a web page. Use CMS software if you want to play
the video on a web page.
 Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
 Alarm
If an event occurs, the event-related video will be transferred to the email specified by the
user or saved to the SD memory, or the event signal will be sent to the Alarm Out port.
 Intelligent Video Analysis
Analyzes the event video according to the user-specified rules to recognize the event.
 ONVIF (Spec 1.02) Compliance
This product supports ONVIF Core Spec. 1.02.
For more information, refer to www.onvif.org.
RECOMENDED PC SPECIFICATIONS
 CPU : Intel(R) Core(TM)2 2.00 GHz or higher
 Operating System : Windows XP, VISTA, 7
Mac OS
 Resolution : 1280X1024 pixels or higher
 RAM : 1GB or higher
 Web Browser : Internet Explorer 6.0 or higher
Firefox, Google Chrome, Safari
 Video Memory : 128MB or higher
RECOMENDED SDHC/SD MEMORY CARD SPECIFICATIONS
 2GB ~ 32GB
 To ensure proper recording of video data, we recommend you use a memory card that
supports at least read/write speed 10Mbps and Class 6.
10_ overview
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Appearance
Quantity
User Manual,
Installer S/W DVD,
CMS S/W DVD
2
Quick Guide
1
7Pin Terminal Block
1
Description
Model Name
● OVERVIEW
Item Name
For communications
SNP-3120/3120V/
3120VH
8Pin Terminal Block
1
For alarm I/O
Cable for the testing
monitor
1
Used to test the camera
connection to a portable display
device
Audio cable
1
English _11
overview
Appearance
Item Name
Quantity
Description
Template
1
Product installation guide
Model Name
SNP-3120
M
ASSY-Tapping Screw
4
Mount Bracket
1
L Wrench
1
Used for installation on the wall or
ceiling
SNP-3120
Used to remove/fix the dome
cover
SNP-3120V/3120VH
 The Test Monitor Cable is connected to a portable displayer and used for testing the camera.
If you intend to use it for an actual monitoring camera, use the BNC cable instead.
12_ overview
AT A GLANCE
❖ SNP-3120
● OVERVIEW
Item
b
c
Description
Main unit
Main unit includes the lens, switch board, PCB boards and screws.
Dome Cover
Dome cover for the lens and unit protection.
Audio
Audio I/O port.
Alarm In / Out
terminals
Used to connect alarm in/out terminal block.
Video, RS-485, Power Used to connect monitor, RS-485 device or power.
ID setup switch
Used to setup the camera ID or communication protocol.
Screw Hole
Used to fix the camera to the wall or ceiling.
Resets the camera settings to the default. Press and hold it for about 5
seconds to turn off the system indicator and restart the system.
Reset Button
Network port
J If you reset the camera, the network settings will be adjusted so that
DHCP can be enabled. If there is no DHCP server in the network, you
must run the IP Installer program to change the basic network settings
such as IP address, Subnet mask, Gateway, etc., before you can
connect to the network.
Used to connect a PoE or LAN cable.
English _13
overview
❖ SNP-3120V
Item
b
c
Description
Surface Mount
Bracket
Used to install the camera directly on the ceiling.
After separating this cover, mount this bracket on to ceiling.
Main unit
Main unit includes the lens, switch board, PCB boards and screws.
Dome Cover
Dome cover for the lens and unit protection.
SD Memory Card
Compartment
Compartment for the SD memory card.
Audio
Audio I/O port.
Heater
Activated when the ambient temperature is under 5ºC to prevent the dome
cover from being covered with frost.
Video, RS-485, Power Used to connect monitor, RS-485 device or power.
ID setup switch
Used to setup the camera ID or communication protocol.
Resets the camera settings to the default. Press and hold it for about 5
seconds to turn off the system indicator and restart the system.
Reset Button
J If you reset the camera, the network settings will be adjusted so that
DHCP can be enabled. If there is no DHCP server in the network, you
must run the IP Installer program to change the basic network settings
such as IP address, Subnet mask, Gateway, etc., before you can
connect to the network.
Alarm In / Out
terminals
Used to connect alarm in/out terminal block.
Network port
Used to connect a PoE or LAN cable.
14_ overview
❖ SNP-3120VH
● OVERVIEW
Item
b
c
Description
Sun Shield Housing
Used to protect the main unit from the sunlight.
Main unit
Main unit includes the lens, switch board, PCB boards and screws.
Dome Cover
Dome cover for the lens and unit protection.
SD Memory Card
Compartment
Compartment for the SD memory card.
Audio
Audio I/O port.
Heater
Activated when the ambient temperature is under 5ºC to prevent the dome
cover from being covered with frost.
Video, RS-485, Power Used to connect monitor, RS-485 device or power.
ID setup switch
Used to setup the camera ID or communication protocol.
Resets the camera settings to the default. Press and hold it for about 5
seconds to turn off the system indicator and restart the system.
Reset Button
J If you reset the camera, the network settings will be adjusted so that
DHCP can be enabled. If there is no DHCP server in the network, you
must run the IP Installer program to change the basic network settings
such as IP address, Subnet mask, Gateway, etc., before you can
connect to the network.
Alarm In / Out
terminals
Used to plug terminal block to connect alarm in/out.
Network port
Used to connect a PoE or LAN cable.
English _15
overview
❖ Camera Wiring Interface Board
For the camera wiring, please refer to the picture below. When using coaxial
communication, a separate control signal connection is not required.
ALARM
VIDEO
ID
485
POWER
PROTOCOL
Controller & Auxiliary Signal Connection
No.
Name
1
2.COM
Usage
Alarm Output 2 (Common)
2
2.NO
3
1.COM
4
1.NO
Alarm Output 1 (Normal Open)
5
1.NC
Alarm Output 1 (Normal Open)
6
GND
Ground
7
IN1
Alarm Input Sensor Terminal 1
8
IN2
Alarm Input Sensor Terminal 2
16_ overview
Alarm Output 2 (Normal Open)
Alarm Output 1 (Common)
Power, Video & Communication Signal Connection
Name
1
VIDEO
Video Output
Usage
2
GND
Ground
3
485+
Controller Data Line
4
485-
Controller Data Line
5
FG
Field Ground
6
AC
AC 24V
7
AC
AC 24V
● OVERVIEW
No.
M
 The provided BNC cable’s blue line is Video Output, while the black line is the Ground.
J
 The maximum power capacity of the built-in relay is 30V DC/2A, 125V AC/0.5A, and 250V
 Power supply adaptor (AC) has no polarities.
AC/0.25A.
 Connecting the power connector and GND incorrectly to the NC/NO and COM ports may cause a
short circuit and fi re, damaging the camera.
 When connecting the camera to an external over-rated product, use a separate relay device to
ensure proper operation.
 To prevent possible inflow of lightning while in test monitoring, perform the test with the FG
terminal grounded.
English _17
installation & connection
DIP SWITCH SETTING
How to set up Protocols and ID DIP Switches
You can control various settings of the camera system using the Communication and ID
DIP switches. Before installing the product, please set up the DIP switches according to the
installation environment.
1. Detach the camera frame from the install base, and place the bottom of the frame
toward you as shown in the picture below.
2. Set the switches according to your installation environment. For more detailed setup
information, please refer to the chart on the next page.
3. The camera may malfunction if the switches are not fully turned On/Off; please
double check the switches before finishing setup.
Camera ID DIP Switch(SW1)
18_ installation & connection
Communication Protocol
DIP Switch(SW2)
Communication Protocol DIP Switch Settings (SW2)
Coaxial communication automatically detects signals, and so does not require a separate
communication setup process.
SW2 Pin No.
OFF
SW2
Purpose
1~4
Protocol Settings
5~6
Baud Rate Settings
7
Response Mode Settings
8
Termination Settings
 Protocol Settings
Select a communication protocol for the camera.
No.
Protocol
SW2-#1
SW2-#2
SW2-#3
SW2-#4
1
AUTO DETECT
OFF
OFF
OFF
OFF
2
Samsung-T
OFF
OFF
OFF
ON
3
Pelco-D
OFF
OFF
ON
OFF
4
Pelco-P
OFF
OFF
ON
ON
5
Samsung-E
OFF
ON
OFF
OFF
6
Panasonic
OFF
ON
OFF
ON
OFF
7
Vicon
OFF
ON
ON
8
Honeywell
OFF
ON
ON
ON
9
AD
ON
OFF
OFF
OFF
10
GE
ON
OFF
OFF
ON
11
BOSCH
ON
OFF
ON
OFF
12
Reserved
ON
OFF
ON
ON
13
Reserved
ON
ON
OFF
OFF
14
Reserved
ON
ON
OFF
ON
15
Reserved
ON
ON
ON
OFF
16
Reserved
ON
ON
ON
ON
English _19
● INSTALLATION & CONNECTION
ON
ON
installation & connection
 Baud Rate Settings
Select the transfer speed of a selected communication protocol.
No.
Baud Rate (BPS)
SW2-#5
SW2-#6
1
2,400
ON
ON
2
4,800
ON
OFF
3
9,600
OFF
OFF
4
19,200
OFF
ON
 Communication Response Settings
Select a communication response method for the camera and controller: Response or No
Response.
SW2- #7
Function
ON
OFF
Response Mode Switch
Response
No Response
 Termination Settings
To prevent the attenuation of communication signals between the camera and controller,
the items at the end of line must be set up with the termination settings.
Camera Input Position
SW2- #8
Termination of Longest Path
ON
On the Path
OFF
- This model is provided with factory defaults of all DIP switches set to OFF. The default
settings are shaded in the table.
20_ installation & connection
M
 To use a third party controller with this product, please contact our After-Sales Service or
Technology Department.
 Controls Using Different Protocols
VICON Protocol
3+Auxilary ON
IRIS OPEN
GE Protocol
IRIS OPEN
Exiting Camera OSD
3+Auxilary OFF
IRIS CLOSE
IRIS CLOSE
ENTER
IRIS OPEN
IRIS OPEN
IRIS OPEN
ESC
IRIS CLOSE
IRIS CLOSE
IRIS CLOSE
 For more information about the protocols, refer to our official website.
Camera ID DIP Switch Settings (SW1)
To set up camera IDs, refer to the “Camera ID Chart” next.
ON
ON
OFF
SW1
English _21
● INSTALLATION & CONNECTION
AD Protocol
Entering Camera OSD
installation & connection
 Camera ID Chart
ID
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
SW1-#1
ON/OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW1-#2
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
SW1-#3
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
22_ installation & connection
SW1-#4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
SW1-#5
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW1-#2
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
SW1-#3
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
SW1-#4
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
SW1-#5
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
SW1-#6
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
English _23
● INSTALLATION & CONNECTION
ID
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
installation & connection
ID
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
SW1-#1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW1-#2
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
SW1-#3
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
24_ installation & connection
SW1-#4
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#5
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW1-#2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
SW1-#3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
SW1-#4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
SW1-#5
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
English _25
● INSTALLATION & CONNECTION
ID
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
installation & connection
ID
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
SW1-#1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW1-#2
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
SW1-#3
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
26_ installation & connection
SW1-#4
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#5
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
SW1-#6
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW1-#7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW1-#2
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
SW1-#3
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
SW1-#4
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#5
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
English _27
● INSTALLATION & CONNECTION
ID
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
installation & connection
INSTALLATION (SNP-3120)
On-ceiling installation
1. Drill a hole of 60mm diameter on the ceiling
and run the wires down through it.
2. Install the Mount Bracket onto the hold and
fix it using 4 screws.
J
 Do not connect the camera to a power outlet
until the installation is complete. Supplying power
in the middle of the installation may cause fire or
damage the product.
3. Connect each camera cable to the proper
terminals on the bottom of the camera. For
more detailed instructions, please refer to
Page 16:“Camera Wiring Interface Board”.
4. DIP switches for communication and ID setup
are located on the bottom of the camera. For
more instructions, please refer to Page 22.
28_ installation & connection
5. Align the “Align The Arrow” triangular edge
of the camera to the marking (shown as “A” in
the diagram) on the left of the “FRONT” side
of the Mount Bracket.
“A”
Mount Bracket
7. Match the screw holes in the camera and
mount bracket, and then fasten with the
screw.
● INSTALLATION & CONNECTION
6. After inserting the camera into the Mount Bracket, turn the camera module clockwise about 25°.
Screw Hole
English _29
installation & connection
Flush Mount Type Installation Example
1. Attach the template, and then drill a hole
according to the 143 mm diameter hole
marked on the template. Drop down the
camera cables through the hole. Drill another
small hole for a screw to secure the camera.
2. Rotate the dome cover counterclockwise to
detach it from the camera.
3. Remove the 3 screws, and then detach the
mount housing from the camera.
30_ installation & connection
● INSTALLATION & CONNECTION
4. Connect each camera cable to the proper terminals on the bottom of the camera (Refer to
Page 16: “Camera Wiring Interface Board”).
Configure the DIP switches on the bottom of
the camera for communication and ID (Refer to
pages 19~21).
5. Install Camera Fit the camera to the hole on
the ceiling, and then secure the camera using 3
Product-enclosed Fixture Screws (M4x20).
Ceiling
Screw
6. Assemble Dome Cover Insert the grooves on the
dome cover into ones on the camera, and then
turn clockwise to fasten.
Screw
Ceiling
English _31
installation & connection
INSTALLING WITH ACCESSORIES (SOLD SEPARATELY)
1. Turn the Dome Cover counter-clockwise
and separate from the camera.
Dome Cover
2. Remove 3 screws and separate the Mount Housing from the camera.
Mount Housing
32_ installation & connection
3. Fix the Mount Housing onto the Hanging
Mount (SBP-300HM) with 4 screws (M4xL16).
J
Hanging
Mount
 Note that the recommended torque for the screw
● INSTALLATION & CONNECTION
fastening is less than 3 kgf, to prevent
deformation of the mount housing.
Mount Housing
4. Connect wires to the Terminal Block and attach it to the bottom side of the camera.
(Refer to the “Camera Wiring Interface Board” at page 16.)
Set the communication protocol and ID DIP switches on the
bottom of the camera unit. (Refer to pages 19~21.)
5. Fix the camera to the Mount Housing by using 3 screws
removed in the step 2.
6. Attach the Dome Cover and turn it clockwise to fix.
English _33
installation & connection
INSTALLATION (SNP-3120V)
Ceiling Mount
1. Use the provided L-shaped wrench to remove the surface mount by loosening 4
screws counter clockwise.
Surface
Body
Screw
2. Drill holes (5 mm in diameter and at least 35 mm in depth for each) for the screws (x4)
to be inserted in the bottom of the surface mount, and insert the provided plastic
anchor (HUD5) to the end.
Insert the cables into the cable hole, and fix the SCREW-TAPPING (TH M4xL30) to
the plastic anchor that was inserted in the hole for fixing the surface mount. (x4)
Surface
Mount
34_ installation & connection
3. Connect the safety wire (attached to the camera) to the surface mount as shown.
Then, arrange the cables.
 For more information about the wiring, refer to “Camera Wiring Interface Board”. (Page 16)
● INSTALLATION & CONNECTION
Safety-wire
4. Arrange the cables inside the surface mount so that they should not be entangled or stuck
in, and align the guide rib of the camera with that of the surface mount. Use the L-shaped
wrench to tighten the screws (x4) so that the camera is secured to the mount.
To ensure waterproofness, take caution lest that the outer gasket should get loose or be
stuck in.
Guide Rib of
Surface Mount
Surface Mount
Guide-Rib of
Main-frame
Screw
Main-frame
Gasket
English _35
installation & connection
Mount onto the optimal adaptor
1. Follow step 1 in “Ceiling Mount” above and remove the surface mount.
2. Insert the cables into the cable hole on the surface mount and fix them to SBP-300HM
(HANGING MOUNT) using SCREW-MACHINE (BH, M4xL10, x4).
3. Repeat step 3 through step 4 in “Ceiling Mount” above to complete the installation.
36_ installation & connection
INSTALLATION (SNP-3120VH)
1. Use the provided L-shaped wrench to loosen 4 screws counter clockwise, which will
help removing the housing.
● INSTALLATION & CONNECTION
Housing
Main-frame
Screw
Screw
2. Fix the housing to the NP 1.5" tapped pipe, wall mount (SBP-300WM) or ceiling
mount (SBP-300CM) by turning it clockwise. For waterproofness and lock between
the two component parts, use the Teflon tape to wrap them around.
Pipe or Mount
Pipe or Mount
NP 1.5' TAP
Housing
Housing
English _37
installation & connection
3. Secure the safety wire (attached to the product) to the housing as shown.
 For details about the cable connection, refer to the “Camera Wiring Interface Board” section in this
manual.
Safety-wire
Safety-wire
4. Arrange the cables inside the housing lest they be damaged or stuck in, and use the
L-shaped wrench to tighten 4 screws to the housing. To ensure waterproofness, this
step needs your special care. Otherwise, the gasket on the outer side of the product
may be loose or just stuck in.
Housing
Main-frame
Gasket
38_ installation & connection
Screw
Optional Accessories for Installation
For your easier installation, you can purchase appropriate optional accessories available.
● INSTALLATION & CONNECTION
1. When installing the camera on a wall
 SNP-3120, SNP-3120V :
Wall mount (SBP-300WM) + Hanging mount
(SBP-300HM)
 SNP-3120VH :
Wall mount (SBP-300WM)
2. When installing the camera on a ceiling
 SNP-3120, SNP-3120V :
Ceiling mount (SBP-300CM) + Hanging mount
(SBP-300HM)
 SNP-3120VH :
Celling mount (SBP-300CM)
English _39
installation & connection
3. When installing the Wall Mount (SBP-300WM) on
a pole bigger than 80mm in diameter :
Pole Mount (SBP-300PM)
4. When installing the Wall Mount (SBP-300WM) on a
cornered wall :
Corner Mount (SBP-300KM)
5. When installing SNP-3120VH on a rooftop of a
building :
Parapet Mount (SBP-300LM)
40_ installation & connection
INSERTING/REMOVING AN SD MEMORY CARD
Inserting an SD Memory Card
Push the SD memory card in the direction of the arrow shown in the diagram.
● INSTALLATION & CONNECTION
J
 Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the
SD memory card.
Removing an SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to
eject the memory card from the slot.
J
 Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from
the slot when released.
 To remove the SD memory card, set <Record> to <Off> from <SD record> and press [Apply
(
)]. (page 94)
 If you have saved data in the SD memory card, removing the SD memory card prior to setting
record to OFF will cause damage to the data stored in the card.
English _41
installation & connection
MEMORY CARD INFORMATION (NOT INCLUDED)
What is a memory card?
The memory card is an external data storage device that has been developed to offer an
entirely new way to record and share video, audio, and text data using digital devices.
Selecting a memory card that’s suitable for you
Your camera supports SDHC memory cards.
You may, however, experience compatibility issues depending on the model and make of
the memory card.
For your camera, we recommend you use a memory card from the following
manufacturers:
SDHC/SD Memory Card : Sandisk, Transcend, Kingston
Playback performance can be affected depending on the speed of memory card, so use
the high-speed memory card.
Memory Card Use
SD and SDHC memory cards feature a switch that disables writing data on to the media.
Having this switch to the Lock position will prevent accidental deletion of data stored in the
memory card but at the same time will also prevent you from writing data on to the media.
❖ Memory Card Components
Contacts
Lock Switch
SD/SDHC
42_ installation & connection
CONNECTING WITH OTHER DEVICE
Power
Connecting to the monitor
Connect the video out port of the camera to the video input port of the monitor.
M
 In the initial installation of the camera, you can connect the camera to the monitor for checking
the connection status.
 Connect the monitor test cable to the output port of the monitor.
Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.
J
 You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.
 If using PoE, the heater will not operate at all. (SNP-3120V/VH)
Use an adaptor if the installation site requires heater operations. Adaptor is sold separately.
For the power specifications, refer to the “Appendix”. (page 108)
English _43
● INSTALLATION & CONNECTION
Monitor
Ethernet
installation & connection
Connecting to Audio Input/Output
Microphone
Amp
Microphone
Speaker
Amp
Speaker
Network
Microphone
PC
1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT
port of the amplifier that the microphone is connected to.
2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.
3. Check the specifications for audio input.
 Audio Codec
G.711 PCM. μ-law 64kbps 8kHz sampling
 Full duplex Audio
 Audio in
Used for mono signal line input (Max.2.4 Vpp)
 Audio out
Used for mono signal line output (Max.2.4 Vpp)
 Line out impedance
600
44_ installation & connection
Alarm I/O Wiring Diagram
AUX COM
2
AUX NO
3
ALM1 COM
4
ALM1 NO
5
ALM1 NC
6
GND
7
ALM IN1
8
ALM IN2
● INSTALLATION & CONNECTION
1
Connecting to the I/O port box
Connect the Alarm I/O signal to the corresponding port of the rear port box.
1 2 3 4 5 6 7 8
1 : 2.COM
2 : 2.NO
3 : 1.COM
4 : 1.NO
M
5 : 1.NC
6 : GND
7 : IN1
8 : IN2
 For further details on each terminal refer to “Camera Wiring Interface Board” (page 16)
English _45
network connection and setup
You can set up the network settings according to your network configurations.
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA
NETWORKING
Connecting to the camera from a local PC in the LAN
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.
Camera
INTERNET
External Remote PC
Camera
Local PC
Firewall
DDNS Server
(Data Center, KOREA)
<Local Network>
M
 A remote PC in an external Internet out of the LAN network may not be able to connect to the
camera installed in the intranet if the port-forwarding is not properly set or a firewall is set.
In this case, to resolve the problem, contact your network administrator.
 By factory default, the IP address will be assigned from the DHCP server automatically. If there is
no DHCP server available, the IP address will be set to 192.168.1.100.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page 51)
46_ network connection and setup
CONNECTING THE CAMERA DIRECTLY TO A DHCP
BASED DSL/CABLE MODEM
External Remote PC
Camera
DDNS Server
(Data Center, KOREA)
1. Use the cross LAN cable to connect the network cable directly to your PC.
2. Run the IP Installer and change the IP address of the camera so that you can use
the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the camera.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [Interface], and set the network type to [DHCP].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
M
 For registering the DDNS settings, refer to “Registering with DDNS”. (page 90)
 For configuring the DDNS settings, refer to “DDNS”. (page 89)
 For setting the network type, refer to “Interface”. (page 88)
English _47
● NETWORK CONNECTION AND SETUP
INTERNET
DSL/Cable Modem
network connection and setup
CONNECTING THE CAMERA DIRECTLY TO A PPPOE
MODEM
INTERNET
PPPoE Modem
External Remote PC
Camera
DDNS Server
(Data Center, KOREA)
1. Use the cross LAN cable to connect the network cable directly to your PC.
2. Run the IP Installer and change the IP address of the camera so that you can use
the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the camera.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [Interface], and set the network type to [PPPoE].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
M
 For registering the DDNS settings, refer to “Registering with DDNS”. (page 90)
 For configuring the DDNS settings, refer to “DDNS”. (page 89)
 For setting the network type, refer to “Interface”. (page 88)
48_ network connection and setup
CONNECTING THE CAMERA TO AN IP ROUTER WITH THE
PPPOE/CABLE MODEM
This is for a small network environment such as homes, SOHO and ordinary shops.
INTERNET
IP Router
PPPoE or
Cable Modem
PPPoE or
Cable Modem External Remote
PC
Camera
Local PC
DDNS Server
(Data Center, KOREA)
Configuring the network settings of the local PC connected to an
IP router
Configuring the network settings of the local PC connected to an IP router, follow the
instructions below.
 Select : <Network Neighborhood>  <Properties>  <Local Area Connection>
 <Properties>  <General>  <Internet Protocol (TCP/IP)>  <Properties>
 <Obtain an IP address automatically> or <Use the following IP address>.
 Follow the instructions below if you select <Use the following IP address>:
ex1) If the address (LAN IP) of the IP router is 192.168.1.1
IP address : 192.168.1.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
ex2) If the address (LAN IP) of the IP router is 192.168.0.1
IP address : 192.168.0.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.1
ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1
IP address : 192.168.xxx.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.xxx.1
M
 For the address of the IP router, refer to the product’s documentation.
 Refer to the “Port Range Forward (Port Mapping) Setup” section of the IP Router’s
documentation. (Page 55)
English _49
● NETWORK CONNECTION AND SETUP
Camera
network connection and setup
BUTTONS USED IN IP INSTALLER
Item
Description
Device Name
Model name of the connected camera.
Click the column to sort the list by model name.
However, search will be stopped if clicked during the search.
b
Mode
Displays either <Static> or <Dynamic> for the current network connection
status.
c
MAC(Ethernet)
Address
Ethernet address for the connected camera.
Click the column to sort the list by Ethernet address.
However, search will be stopped if clicked during the search.
IP Address
IP address.
Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
The factory default is “192.168.1.100”.
Protocol
Network setting for the camera.
The factory default is “IPv4”.
Cameras with the IPv6 setting will be displayed “IPv6”.
UPnP Status
This function is not currently implemented.
50_ network connection and setup
Item
m
M
URL
DDNS URL address enabling access from the external Internet.
However, this will be replaced with the <IP Address> of the camera if
DDNS registration has failed.
IPv4
Scans for cameras with the IPv4 setting.
IPv6
Scans for cameras with the IPv6 setting.
Search
Scans for cameras that are currently connected to the network.
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
Auto Set
The IP Installer automatically configures the network settings.
Manual Set
You should configure the network settings manually.
Exit
Exits the IP Installer program.
 For the IP installer, use only the installer version provided in the installation DVD or use the latest
one if available. You can download the latest version from the product website.
STATIC IP SETUP
Manual Network Setup
Run <IP Installer_vX.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M
 For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not
support this function.
1. Select a camera in the search list.
Find the MAC (Ethernet) address
labeled on the rear of the camera.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Manual Set].
The Manual Setting dialog appears.
The default values of <IP Address>,
<Subnet Mask>, <Gateway>, <HTTP Port> and <VNP Port> of the camera will
be displayed.
English _51
● NETWORK CONNECTION AND SETUP
Description
network connection and setup
3. In the <Address> pane, provide the
necessary information.
 MAC (Ethernet) Address : The MAC
(Ethernet) address of the applicable
camera will be set automatically so
you don't need to input it manually.
M
 You can configure the static IP settings
only if the DHCP checkbox is unchecked.
If using an IP router
 IP Address : Enter an address falling in
the IP range provided by the IP router.
ex) 192.168.1.2~254,
192.168.0.2~254,
192.168.XXX.2~254
 Subnet Mask : The <Subnet Mask> of
the IP router will be the <Subnet Mask>
of the camera.
 Gateway : The <Local IP Address> of
the IP router will be the <Gateway> of
the camera.
M
 The settings may differ depending on the connected IP router model.
For more information, refer to the user manual of the applicable router.
 Refer to the “Port Range Forward (Port Mapping) Setup” section of the IP Router’s
documentation. (Page 55)
If not using an IP router
For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.
4. In the <Port> pane, provide
necessary information.
 HTTP Port : Used to access the
camera using the Internet browser,
defaulted to 80. Use the spin button
to change the HTTP Port value.
 VNP Port : Used to control the video
signal transfer, defaulted to 4520.
5. Enter the password.
This is the login password for the “admin” user who accesses the camera.
The default password is “4321”.
52_ network connection and setup
J
 The default password can be exposed to a hacking thread so it is recommended to change the
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
7. When the manual setup including IP is completed, the camera will restart.
If the IP router has more than one camera connected
Configure the IP related settings and the Port related settings distinctly with each other.
Category
Camera #1
Camera #2
IP related settings
IP Address
Subnet Mask
Gateway
192.168.1.100
255.255.255.0
192.168.1.1
192.168.1.101
255.255.255.0
192.168.1.1
Port related settings
HTTP Port
VNP Port
8080
4520
8081
4521
M
 If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar
of the Internet browser before you can access the camera.
ex) http://IP address : HTTP Port
http://192.168.1.100:8080
Auto Network Setup
Run <IP Installer_vX.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M
 For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not
support this function.
1. Select a camera in the search list.
Find the MAC (Ethernet) address labeled
on the rear of the camera.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
2. Click [Auto Set].
The Auto Setting dialog appears.
The <IP Address>, <Subnet Mask>,
and <Gateway> will be set automatically.
English _53
● NETWORK CONNECTION AND SETUP
6. Click [OK].
Manual network setup will be completed.
network connection and setup
3. Enter the password.
This is the login password for the
“admin” user who accesses the
camera. The default password is
“4321”.
 The default password can be exposed to
a hacking thread so it is recommended to
change the password after installing the
product.
Note that the security and other related issues
caused by the unchanged password shall be
responsible for the user.
4. Click [OK].
Auto network setup will be completed.
DYNAMIC IP SETUP
Dynamic IP Environment Setup
 Example of the Dynamic IP environment
- If an IP router, with cameras connected, is assigned an IP address by the DHCP
server
- If connecting the camera directly to modem using the DHCP protocols
- If IPs are assigned by the internal DHCP server via the LAN
Checking the Dynamic IP
1. Run the IP Installer on the user’s local
machine to display cameras allocated
with <Dynamic IP> addresses in the
list.
2. Select a camera in the list, and click
[Manual Set] to check the <Dynamic
IP> of the camera.
If you uncheck <DHCP>, you can
change IP or <Port> to <Static>.
54_ network connection and setup
PORT RANGE FORWARD (PORT MAPPING) SETUP
If you have installed an IP router with a camera connected, you must set the port range
forwarding on the IP router so that a remote PC can access the camera in it.
● NETWORK CONNECTION AND SETUP
Manual Port Range Forwarding
1. From the Setup menu of the IP router,
select <Applications & Gaming> <Port Range Forward>.
For setting the port range forward for
a third-party IP router, refer to the user
guide of that IP router.
2. Select <TCP> and <UDP Port> for
each connected camera to the IP
router.
Each port number for the IP router
should match that specified in
<Network> - <Port> from the camera's Setup menu.
3. When done, click [Save Settings].
Your settings will be saved.
M
 Above sample instructions are based on the CISCO’s IP Router (Model: LINKSYS).
 The settings may differ depending on the connected IP router model.
For more information, refer to the user manual of the applicable router.
English _55
network connection and setup
Setting up Port Range Forward for several network cameras
When several network camera connect to one IP router device, you should forward the
TCP 943 port of the router to the TCP 943 port of a connected camera.
J
 If you don't set properly the TCP 943 port of the router, you cannot get any video stream from the
web page of the camera.
 TCP 943 port is a port for the Silverlight policy server of a camera.
When Camera1 and Camera2 are connected to a router :
Ù
User
Internet
Ú
Start
943
3000
3001
4520
4521
8080
8081
End
943
3000
3001
4520
4521
8080
8081
IP router
Protocol
TCP
TCP/UDP
TCP/UDP
TCP/UDP
TCP/UDP
TCP/UDP
TCP/UDP
IP Address
192.168.1.100
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101
192.168.1.100
192.168.1.101
Ù
Camera1 (192.168.1.100)
Web Server Port
8080
VNP Port
4520
RTSP Port
3000
Policy Server Port
943
Ù
Camera2 (192.168.1.101)
Web Server Port
8081
VNP Port
4521
RTSP Port
3001
Policy Server Port
943
 You can set a rule of Port Forwarding on the IP router device through its configuration web page.
 You cannot change the Silverlight policy server port of a camera.
 You can change the ports of the camera except the policy server port through its
configuration web pages.
56_ network connection and setup
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC
2. Double-click a camera to access.
The Internet browser starts and connects
to the camera.
M
 Access to the camera can also be gained by typing the camera's IP address in the address bar of
the Internet browser.
CONNECTING TO THE CAMERA FROM A REMOTE PC VIA
THE INTERNET
Since using the IP Installer on a remote computer that is not in the IP Router’s network cluster
is not allowed, users can access cameras within an IP Router’s network by using the camera’s
DDNS URL.
1. Before you can access a camera in the IP router network, you should have set the
port range forward for the IP router.
2. From the remote PC, launch the Internet browser and type the DDNS URL address
of the camera, or the IP address of the IP router in the address bar.
ex) http://www.samsungipolis.com/[Product ID]
English _57
● NETWORK CONNECTION AND SETUP
1. Run the IP Installer.
It will scan for connected cameras and
display a list of them.
web viewer
CONNECTING TO THE CAMERA
Normally, you would
1. Launch the Internet browser.
2. Type the IP address of the camera in
the address bar.
ex) • IP address (IPv4) : 192.168.1.100
 http://192.168.1.100
- the Login dialog should appear.
• IP address (IPv6) : 2001:230:abcd:
ffff:0000:0000:ffff:1111
 http://[2001:230:abcd:ffff:0000:0000:
ffff:1111]
If the HTTP port is other than 80
1. Launch the Internet browser.
2. Type the IP address and HTTP port number of the camera in the address bar.
ex) IP address : 192.168.1.100:HTTP Port number(8080)
 http://192.168.1.100:8080 - the Login dialog should appear.
Using URL
1. Launch the Internet browser.
2. Type the DDNS URL of the camera in the address bar.
ex) URL address : http://www.samsungipolis.com/[Product ID]
- the Login dialog should appear.
58_ web viewer
To check the DDNS address
Once you register a dynamic IP-based device with the DDNS server, you can easily check
the changed IP when you try to access the device.
To add the IP address to the <DDNS> server, visit www.samsungipolis.com and register
your device, and set the DDNS option to <Samsung DDNS> before providing the host
name for the DDNS server.
LOGIN
The default user ID is “admin”, and the default password is “4321”.
1. Enter “admin” in the <User Name>
input box.
2. Enter “4321” in the <Password> input
box.
If the password is changed, enter the
changed password instead.
3. Click [OK].
If you have logged in successfully, you
will the Live Viewer screen.
M
 For security purposes, ensure that you
change the password in <System>
- <User>.
The administrator ID, “admin”, is fixed and can not be changed.
 The default password can be exposed to a hacking thread so it is recommended to change the
password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
 If you check the “Remember my password” option when your input is done, in future you will be
logged in automatically without being prompted to enter the login information.
J
 If you are using Internet Explorer 7.0 or 8.0 as the default web browser, you can view the best
quality image with a screen ratio of 100%. Reducing the ratio may cut the image on the borders.
English _59
● WEB VIEWER
If the camera is connected directly to the DHCP cable modem, DSL modem, or PPPoE
modem, the IP address of your network will be changed each time you try to connect to
the ISP (Internet Service Provider) server.
If this is the case, you will not be informed of the IP address changed by DDNS.
web viewer
This network camera uses Microsoft Silverlight for displaying the video.
INSTALLING SILVERLIGHT RUNTIME
If your PC has not installed Silverlight Runtime or has just installed an old runtime version, you will
be redirected to the Silverlight Runtime installation page automatically when accessing the web
viewer.
1. Click <Click Here>.
2. When the file download dialog pops up,
click <Run>.
3. When the download is completed, click
<Run>.
4. The Silverlight Runtime installation page
will be displayed. <Install now> to proceed with the installation.
60_ web viewer
5. When done, click <Close>.
● WEB VIEWER
6. Close and restart the web browser, and
try to access the Web Viewer.
When Silverlight Runtime is properly
installed, you will see the Live screen.
J
 For normal installation, set the Block
Popup setting as follows:
Internet Explorer  Tools  Block
Popup  Always allow popups from
the current site(A)
 However, MAC OS X users who are not connected to the Internet can use the provided installation
DVD to install Silverlight Runtime (Run the executable “Silverlight_xxx.dmg” in the DVD. You will be
guided through installation of the software).
English _61
web viewer
USING THE LIVE SCREEN
Item
Description
Monitoring
Move to the monitoring screen.
b
Playback
Switch to the monitoring screen that plays recording data in the SD memory.
c
Setup
Move to the Setup screen.
Viewer Screen
Displays the Live video on the screen.
Alarm Output
Activate the Alarm Out port.
Audio
Display the audio Listen and Talk toggle button on the screen.
Hide the alarm
indicator
Hides the alarm indicator near the border of the viewer screen.
Camera Menu
Used to retrieve and customize the Camera Setup menu.
For selecting and saving each menu item, refer to “Using the Camera Menu”.
(page 67)
62_ web viewer
Item
Description
PTZ
You can adjust the Pan/Tilt angle of the camera as well as the zoom factor.
Digital PTZ
You can use the mouse wheel to activate the digital zooming.
Screen
Optimization,
Full Screen
Adjust the screen to the optimal size, and display the Full Screen icon on the Live
screen.
Capture
Saves the snapshot as an image file in the .bmp format.
You can select a profile type in <Video profile> under the <Audio & Video> setup
menu.
m
Video Format
M For IE 6.0 users, press the Browse button next to the <Video profile> dialog
and select a profile type again if the selected profile is not played.
M If the “Invalid codec” message is displayed, select a profile type from the profile
list again.
M
 If the temperature drops below the operational range, video signal may not be produced. In such
cases, please wait for the video.
To capture the snapshot
1. Click [
] on the scene to capture.
The Capture dialog should appear.
2. Click [Save] button.
The screenshot will be saved in the
specified path.
M
 If you are using the IE8 as the default web
browser, select “Tools-Internet
Options-Security” and uncheck “Use
protected mode”.
English _63
● WEB VIEWER
web viewer
To toggle the audio sound
1. Click the [Audio (
)] button.
The corresponding button will be displayed in the Viewer.
2. Click the button to listen to / mute the
sound as you wish.
This button operates as a toggle button.
To toggle the microphone sound
1. Click the [Mic (
)] button.
The corresponding button will be displayed in the Viewer.
J
 “Cannot find audio recording device”
message appears if there is no
Microphone.
2. Click the button to start / stop talking.
This button operates as a toggle button.
The Silverlight permission dialog appears when you click the microphone button.
To fit the full screen
1. Click the [Full Screen (
)] button.
The corresponding button will be displayed in the Viewer.
2. Click the button.
This will fit the Viewer to the full screen.
3. To exit the full screen mode, press [Esc] on the keyboard.
To control the PTZ
1. Press the [PTZ (
)] button.
2. When the PTZ button bar appears on
the screen, use the direction buttons to
adjust the camera angle, zoom factor
or focus to your preference.
M
 For further details on PTZ use, refer to
“PTZ setup”. (page 83)
64_ web viewer
To activate a preset
To perform the designated preset in the Live screen, right-click the mouse and select your
desired preset number.
1. Click the [Playback (
● WEB VIEWER
PLAYBACK
)] button.
2. Specify the start time and end time of
your search.
3. Select a search type.
)] button.
4. Click the [Search (
The search results will be displayed in
the list.
M
 If more than 500 events are recorded
within the search period, your search will
be limited up to the date when the 500th event is recorded.
For instance, if the search period is between 10th and 15th day of the month, and more than 800
events were recorded 10th through 11th, your search will be limited up to 11th day with a total of
800 events, and events after then (from 12th) will not be found.
5. Select a data item to play in the search
list.
6. Click the [Play (
)] button.
7. To stop playing the video, click [Stop
)].
(
To return to the search screen, click
)].
[Exit (
To check time information of the playing video
1. Click the [About (
)] button.
2. Date and time information appears on the screen.
English _65
web viewer
To back up the searched video
1. Click [
] on the scene to back up.
Save as window appears.
2. Click [Save].
The screenshot will be backed up to the
specified path.
M
 If you are using the IE8 as the default web
browser, select “Tools-Internet
Options-Security” and uncheck “Use
protected mode”.
PLAYING THE BACKUP RECORDINGS
You can play backup recordings by using the SlimPlayer.
To download SlimPlayer
1. Click [SlimPlayer (
)].
You will see a download dialog where
you can specify the download path.
2. Specify the path with a proper file name
and click [Save].
3. Unzip the downloaded file and run the
executable.
66_ web viewer
camera setup
USING THE CAMERA MENU
Follow the steps below if you run the Web Viewer for setting the menus.
1. Launch the Web Viewer.
● CAMERA SETUP
2. Click [Camera Menu (
)] in the left
corner of the Live screen.
The camera setup menu appears.
3. Use the Up/Down (▲/▼) buttons to move
to a desired item.
4. Click [Enter (
)]. Then, use the up/
down (▲/▼) button to move to a desired
item.
5. To access a sub menu item, click
)].
[Enter (
6. To move to previous menu or exit the menu setup, click [Cancel (
)] button.
: This arrow appears next to a menu that contains sub items.
J
 If <IV analysis function> is enabled, camera’s OSD menu operation can be set as an event.
CAMERA SETTING
You can set up the general functions of camera module.
Starting the Menu
1. Click [Camera Menu (
)] button.
2. When main menu shows up on screen,
move to desired menu by using direction
button.
Main Menu
Camera Setting
P/T Setting
OSD Setting
Initialize
English _67
camera setup
Zoom/Focus
Main Menu Ö Camera Setting Ö Zoom/Focus
 Focus Mode
- AUTO : Performs continuous auto-focus.
- MANUAL : Changes the camera mode to
Manual Focus.
- ONESHOT : Auto-focuses the camera
once after the Pan, Tilt, or Zoom
function is used.
 Digital Zoom : Enables the maximum digital
zoom. Setting the digital zoom to 16X provides a total zoom of 192X.
M
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
 Unlike the optical zoom, the graphics quality
Zoom/Focus
of the digital zoom decreases as its zoom
ratio increases.
Focus Mode
Digital Zoom
ATW(IN)
OFF
--MEDIUM
OFF
ONESHOT
OFF
 The auto-focus function may not operate
normally under the following conditions :
- When background illumination is low
- While Slow-Shutter is in operation
- If the zoom level is set too high
- When background illumination is too high
- If a long distance object and a close distance object appear together within a monitoring area
- If there is no contrast, e.g. Ceiling or a wall
- If the camera is facing a thin horizontal line
 Auto Focus focuses on an object in the center of the screen; objects around the screen edges
may not be properly in focus.
68_ camera setup
White Balance
The White Balance menu adjusts the balance of the screen colors under different lighting
conditions.
 ATW(IN) : Adjusts the screen color to be
Camera Setting
optimal in an indoor environment.
(Operating Temperature: about 2,500°K ~
Zoom/Focus
White Balance
ATW(IN)
about 9,300°K)
Exposure
Back Light
OFF
 ATW(OUT) : Automatically adjusts the
AGC
--screen color to be optimal in bright outDNR
MEDIUM
doors environments. (Operating TemperaXDR
OFF
Day/Night
ture: about 2,000°K ~ about 10,000°K)
Others
 AWC : Adjusts the screen color to be optimized to the current lighting and monitor
conditions. Using this setting may require an readjustment if the lighting conditions
changes.
 MANUAL : Enables customization of the Red and Blue gains.
M
 White Balance may not work properly under the following conditions.
- When the color temperature of the environment surrounding the subject is out of the control
range.
- When the ambient illumination of the subject is dim.
- If the camera is directed towards a fluorescent light or is installed in a place where illumination
changes dramatically, White Balance adjustments may not deliver consistent results.
English _69
● CAMERA SETUP
Main Menu Ö Camera Setting Ö White Balance
camera setup
Exposure
The Exposure settings are to control the camera’s exposure meter.
Main Menu Ö Camera Setting Ö Exposure
 Brightness : Adjusts the screen
brightness.
(Over 32: Brighter, Under 32: Darker)
 It may not fully operable under extremely low
lighting condition.
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
ATW(IN)
OFF
---
MEDIUM
 Iris
OFF
- AUTO : Automatically adjusts the exposure meter.
- MANUAL : Enables manual
adjustment of the exposure meter.
(Over 32: Brighter, Under 32: Darker)
Exposure
 Shutter : Controls the camera’s electronic
Brightness
32
shutter.
Iris
AUTO
Shutter
OFF
- OFF : The shutter speed is fixed at 1/60
Sens-Up
AUTO
for NTSC and 1/50 for PAL.
Operates when Iris is on the Auto Mode.
- A. FLK : Select this setting when you
experience picture flickering.
Flickering can happen when artificial
lighting frequencies clash with camera frame rates.
- MANUAL : Enables manual adjustment of the shutter speed.
 Sens-Up
- AUTO : Automatically detects light levels and maintains a clear picture at night or
under low-light conditions.
- Sens-Up Limit : Adjusts to the maximum-powered zoom per frame.
M
 While the Internal Sync mode is in effect, setting the shutter to ‘---’ and facing the camera directly
to a bright light source may cause poor camera performance.
 Brightness is disabled when the Iris is in Manual mode.
 Shutter is disabled when the WDR is turned on.
 Sens-Up is disabled when the shutter is in Manual mode.
70_ camera setup
Back Light
Backlight Mode Settings
Unlike other cameras, Samsung Techwin’s unique A1 DSP chip gives you a clear image of
the subject even with bright backlight.
 Back Light
- OFF : Disables the Backlight mode.
- WDR : Activates the Wide Dynamic
Range mode.
- BLC : Activates a user defined backlight
compensation mode.
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
ATW(IN)
OFF
--MEDIUM
OFF
WDR
When there are both bright and dark areas at the same time, this mode makes both areas
distinctive.
Main Menu Ö Camera Setting Ö Back Light Ö WDR
 Limit : Three WDR sensitivity levels are
available in 3 : LOW, MEDIUM, and HIGH.
Note that the higher the sensitivity level,
the lower the contrast in the light and dark
areas becomes.
 Level : Adjusts the screen brightness in
WDR mode.
M
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
ATW(IN)
WDR
--MEDIUM
OFF
 WDR is disabled when the VPS mode is
turned on.
 WDR is disabled if the Iris is in Manual mode.
 During WDR operation, noise, discoloration,
spots, and whitish symptoms may occur
depending on lighting conditions. If they
occur, stop using WDR.
WDR Setting
Limit
Level
MEDIUM
09
English _71
● CAMERA SETUP
Main Menu Ö Camera Setting Ö Back Light
camera setup
BLC
You can selectively choose a screen area to see objects within the area more clearly than
others.
Main Menu Ö Camera Setting Ö Back Light Ö BLC
 You can adjust the position and size of the
backlight compensation area.
M
 BLC is disabled if the Iris is in Manual mode.
 Color saturation may occur depending on the
environment.
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
ATW(IN)
BLC
--MEDIUM
OFF
BLC
↑ : Up ↓ : Down
← : Left → : Right
W : Decrease T : Increase
AGC
AGC (Automatic Gain Control) adjusts the camera’s gain control and the screen brightness if
the camera has captured an object under low-light conditions.
Main Menu Ö Camera Setting Ö AGC
 The OFF, LOW, MEDIUM, HIGH, and
MANUAL modes are available.
M
 If you select the AUTO for Day/Night, you
cannot use the AGC menu.
72_ camera setup
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
ATW(IN)
OFF
--MEDIUM
OFF
DNR (Dynamic Noise Reduction)
DNR significantly reduces the amount of low luminance noise.
Main Menu Ö Camera Setting Ö DNR
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
ATW(IN)
OFF
--MEDIUM
OFF
XDR (eXtended Dynamic Range)
XDR illuminates darker spots of an image while retaining the same light level for brighter
spots to even out the overall brightness of the image with high contrast between bright and
dark spots.
Main Menu Ö Camera Setting Ö XDR
 The OFF, LOW, MEDIUM and HIGH modes
are available.
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
ATW(IN)
OFF
--MEDIUM
OFF
English _73
● CAMERA SETUP
 OFF : Disables the noise reduction function.
 LOW : Reduces only a small amount of
noise, but generates almost no
afterimage.
 MEDIUM : The most commonly used
mode. Reduces a suitable amount of noise
while generating a subtle afterimage.
 HIGH : Reduces noise significantly, but
generates obvious afterimages.
camera setup
Day/Night
The Day & Night function allows the camera to switch between the Color and B/W modes.
Main Menu Ö Camera Setting Ö Day/Night
 Mode
- AUTO : Operates in Color mode most times,
and switches to B/W mode if a low light level
is detected during nighttime.
- COLOR : Operates in Color mode at all
times.
- BW : Operates in B/W mode at all times.
By using the Burst On/Off sub menu,
burst signals can be retained or disabled.
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
ATW(IN)
OFF
--MEDIUM
OFF
 If the camera is in B/W mode and connected to equipment that requires external sync through burst
signals, set the Burst On/Off option to “On”.
 Dwell Time : The duration of both the lighting
conditions can be customized to let the camera delay the switching between the daytime
and night-time settings.
M
 Using B/W mode under sunlight or a halogen
lamp may decrease the focusing
performance.
74_ camera setup
Day/Night
Mode
Dwell Time
AUTO
3 SEC
Others
Main Menu Ö Camera Setting Ö Others
M
 The Stabilizer uses the digital zoom and may
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
DNR
XDR
Day/Night
Others
ATW(IN)
OFF
--MEDIUM
OFF
Others
Sharpness
Freeze
Stabilizer
VPS
Posi/Nega
2
OFF
OFF
OFF
+
cause low picture quality.
 The Stabilizer is disabled if the ambient light
is too low.
 The Stabilizer is disabled if the field of view has very low or no contrast, e.g. The sky or a white wall.
 VPS is disabled when the Freeze is turned on.
Image Hold
Main Menu Ö P/T Setting Ö Image Hold
 When the camera is moving between
presets locations, this function freezes the
cameras image until the camera reached
the next location. This is useful to help the
screen observer keep sharp eyes and to
monitor multiple locations within a network.
P/T Setting
Image Hold
Jog Speed
Max Speed Level
OFF
MANUAL
5
English _75
● CAMERA SETUP
 Sharpness : Sharpens outlines of an
image.
 Freeze : Stops or reanimates an image.
 Stabilizer : The Stabilizer compensates
for any small movements of the camera
caused by due to the wind and other
reasonable causes.
 VPS : This function enhances the outline of
moving subject, which improves the sharpness of a captured image as fine as a still
image.
 Posi/Nega : Setting to + outputs normal
video, where setting to – outputs inverted
brightness and color.
camera setup
Jog Speed
You can adjust the pan/tilt speed of the controller in use.
Main Menu Ö P/T Setting Ö Jog Speed
 MANUAL : The angle of the controller
handle determines the speed of Pan and
Tilt; the more you tilt the controller, the
faster the camera spins.
 10/20/30/40/50/60 : Maintains speed
regardless of the angle of the controller
handle.
P/T Setting
Image Hold
Jog Speed
Max Speed Level
OFF
MANUAL
5
Max Speed Level
Adjusts the maximum speed of Pan and Tilt while performing the Preset and Sequencing
actions.
Main Menu Ö P/T Setting Ö Max Speed Level
 1~7 : Pan and Tilt operations can be set up
to 650°/ sec.
P/T Setting
Image Hold
Jog Speed
Max Speed Level
76_ camera setup
OFF
MANUAL
5
OSD SETTING
OSD Setting
● CAMERA SETUP
OSD Setting is to set up the OSD (On Screen Display) functions.
Main Menu Ö OSD Setting
 Camera ID : Displays or hides Camera ID in
the upper left of the screen.
 Camera Name : Add a name to the camera.
 Seq. Status : Displays or hides the status
of a sequence action that is in progress.
 PTZ Position : Displays or hides the status
of the Pan, Tilt, and Zoom operation that is
in progress.
 Language : Enables changing the system
language. This camera supports English,
Chinese, French, German, Spanish, Portuguese, Korean and Italian.
M
 When selecting the Camera Name and Preset
Name, the screen displays the Left keypad.
Main Menu
Camera Setting
P/T Setting
OSD Setting
Initialize
OSD Setting
Camera ID
Camera Name
Seq. Status
PTZ Position
Language
Others
ON
ON
ON
ENGLISH
 Names can be up to 12 characters and can
be entered via the joystick and the Enter key.
Once a name is entered, use the joystick and
the Enter key to perform the Set command
and save the name.
Camera Name [
]
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
1234567890 ( )
[]-/#*!?,.
BACK
SPACE
CLR
SET
English _77
camera setup
OSD Setting (Others)
Main Menu Ö OSD Setting Ö Others
 Direction : Indicates the current angle of the
camera: East, West, South, North, Southeast, Southwest, Northeast, or Northwest.
- Set North Dir. : Set up a North direction
for the camera.
 Clock Setting : Customize the camera
clock; you can schedule sequence actions
to perform automatically.
- Display : Shows or hides the clock from
the screen.
- Date Format : Changes the display
format of the camera date:
DD/MM/YYYY or MM/DD/YYYY.
78_ camera setup
OSD Setting
Camera ID
Camera Name
Seq. Status
PTZ Position
Language
Others
OSD Setting
Direction
Clock Setting
ON
ON
ON
ENGLISH
INITIALIZE
Initialize
 Auto Refresh : Enables optimizing the status of the camera’s built-in electric circuits
and components on a regular basis.
(A regular operation can be scheduled.)
This mode can be used to maintain and
repair the current settings of the camera
when anomalous operations occur: e.g.
The camera happened to directly face a
light source, or the settings have been canceled after the camera repeatedly rotated
in all four directions for a long time to monitor a specific location.
The default setting is Off.
- OFF, 1~7 Days : Selecting Off disables
Auto Refresh and selecting 1~7 Days
automatically executes it after 1~7 days
has passed.
M
● CAMERA SETUP
Main Menu Ö Initialize
Main Menu
Camera Setting
P/T Setting
OSD Setting
Initialize
Initialize
Auto Refresh
OFF
 Auto Refresh takes approximately 10 seconds
to finish. If Auto Refresh activates in the
middle of a sequence action, the camera
pauses the sequence action and performs an Auto Refresh, then resumes the sequence action
once the refresh is complete.
English _79
setup screen
SETUP
You can configure the audio & video, network, event and system settings of the camera in the
network.
)].
1. In the Live screen, click [Setup (
2. The Setup screen appears.
AUDIO & VIDEO SETUP
Video profile
1. From the Setup menu, select the <Audio
)> tab.
& Video (
2. Click <Video profile>.
3. Select a <Video profile> number.
4. Click the input box of each item and
enter / select a desired value.
 The context menu may differ depending on the
selected codec type.
 Default profile : This is the default
video profile.
 Fixed framerate profile : Fix the frame
rate of the selected profile regardless
of the settings of other profiles.
 E-mail/FTP profile : Video profile to be transferred to the specified email or FTP
site.
 Only the MJPEG codec can be set as the E-mail/FTP profile.
 Record profile : This is the profile that is applied to video recording.
5. When done, click [Apply (
M
)].
 Profiles using H.264 codec can be stored in the SD memory only in resolutions of 640x480 or
less.
MPEG4 videos can not be stored in the SD memory.
80_ setup screen
To add a video profile
You can add as many codecs as necessary so that a variety of profiles can be applied
according to the recording condition.
1. Select a profile number.
3. Specify the conditions under which the codec will be applied.
4. Specify the details of the selected codec including resolution and frame rate.
 Resolution : Set the video size of the MPEG4, H.264, and MJPEG files.
 Framerate : Specify the frame rate.
 Compression : Specify the compression rate of the video.
 Bitrate control : You can select one from constant bit rate and variable bit rate for
compression. Constant bit rate (CBR) varies the video quality and fixes network
transfer bit rate, while variable bit rate emphasizes the quality by varying network
transfer bit rate.
 Target bitrate : Specify the bit rate at which you will transfer the video.
 Encoding priority : You can set the video transfer method to Framerate or
Compression.
 GOP size : Select a GOP size between 1 and 15.
 Profile : You can select the H.264 profiling method.
 Entropy coding : Reduce the possible compression loss due to encoding.
 Multicast(VNP) : Specify the use of the VNP protocol.
- IPv4 : Enter an IPv4 address with which you can connect to the IPv4 network.
- Port : Specify the video communication port.
- TTL : Set the TTL for the VNP packet.
 Multicast(RTP) : Specify the use of the RTP protocol.
- IPv4 : Enter an IPv4 address with which you can connect to the IPv4 network.
- Port : Specify the video communication port.
- TTL : You can set the TTL for the RTP packet.
What is GOP size?
GOP (Group of Pictures) is a set of video frames for MPEG4 and H.264 format
compression, indicating a collection of frames from the initial I-Frame (key frame) to the
next I-Frame. GOP consists of 2 kinds of frames: I-Frame and P-Frame.
I-Frame is the basic frame for the compression, also known as Key Frame, which
contains one complete image data. P-Frame contains only the data that has changed
from the preceding I-Frame.
You can set between 1 and 15 for the MPEG4 and H.264 CODEC.
English _81
● SETUP SCREEN
2. Provide the name and select a codec.
setup screen
Video setup
To set the privacy zone
You can specify a certain area of the camera video to be protected for your privacy.
1. From the Setup menu, select the
<Audio & Video (
)> tab.
2. Click <Video setup>.
3. Select a <Pattern> that will be applied
to the privacy zone.
 If you select [Solid] from the <Pattern>
items, the selected zone will be displayed in
grey.
If you select one from [P1~P3], the selected
zone will be displayed in mosaic pixels.
4. Click an area on the image and select 4
corner points to specify a desired zone.
A popup appears where you enter a name for the zone and click [Apply (
 Do not drag an area to specify a privacy zone; it does not work.
5. To delete the selected area, click [Delete (
6. When done, click [Apply (
 You can specify up to 12 zones.
)].
)].
Audio setup
You can configure the I/O settings of the audio source from the camera.
1. From the Setup menu, select the
<Audio & Video (
)> tab.
2. Click <Audio setup>.
3. Adjust the audio I/O levels to your
preference.
 Audio-In : Set the audio input value.
 Audio-Out : Set the audio output
value.
4. When done, click [Apply (
82_ setup screen
)].
)].
PTZ setup
You can change the direction of lens and activate the zoom.
)> tab
● SETUP SCREEN
1. Select the <Audio & Video (
from Setup menu.
2. Click <PTZ setup>.
3. Click [Direction Adjustment (
)].
 [Change direction to (
)/(
)/
)/(
)] : Change the direction of
(
camera lens.
 [Moving speed control (
)] :
The bigger the number is, the faster
the moving speed becomes.
4. Set the zoom and focus control buttons.
 [Zoom In (
)] : Zooms in the
screen.
 [Zoom Out (
)] : Zooms out the
screen.
 [Adjust Focus ( / )] : Adjusts the
focus in the screen.
 [Zoom Speed Control (
)] :
The bigger the number is, the faster the
zoom speed becomes.
5. Set the preset.
To add a preset
1. Select the preset number to add.
2. Set the name for the preset.
3. Press the [
] button.
To delete a preset
1. Select the preset number to delete.
2. Press the [
] button.
English _83
setup screen
To move a preset
1. Select a preset number that you want to move.
2. Press the [
] button.
To set the camera operation for the preset
1. Select the number of preset that you
want to configure.
2. Press the [
] button.
3. When the Setup window appears,
select each item and set appropriately.
- PTZ Coordinate : Set the Pan/Tilt/
Zoom position of the preset.
- Focus / Zoom : Select MANUAL/
AUTO or set One Shot AF mode to OFF, or select a speed rate between 2 and
12.
- White Balance : Set INDOOR/OUTDOOR/Manual(Red Gain, Blue Gain) as appropriate.
- Exposure : Configure the settings for Brightness/Iris/Iris Level/SHUTTER Mode (Off,
Manual, A.FLK)/Shutter Speed, Sens-up Mode(Off,ON)/Sens-up Limit.
- BackLight : Select one from Off/WDR (WDR Level, WDR Limit)/User.
- Day / Night, AGC : Select one from Color/Black and White/Auto.
- Others : Set DNR (Off/Low/Middle/High)/XDR(Off/Low/Middle/High) as appropriate.
4. When done, click [Apply (
)].
To configure the swing settings
Swing is a monitoring function that moves between two preset points and enables you to
trace the motion.
1. Set <Mode> in <Sequence setup> to
<Swing>.
The menu screen will switch to the swing
setting screen.
2. Select a swing setting mode.
 Pan swing : You can set the swing
monitoring only using the PAN function.
 Tilt swing : You can set the swing
monitoring only using the Tilt function.
 Pan & Tilt swing : You can set the swing monitoring only using both PAN and Tilt
functions.
84_ setup screen
3. Set <First preset> and <Second preset> to specify a swing range.
4. Set the moving speed and dwell time.
5. Press the [
] button.
The first preset, second preset, speed and dwell time will be saved in set mode.
] button.
7. Press the [
] button.
The running swing will be stop.
To set a group
The group function enables you to group various presets before calling them in sequence.
Each group can contain up to 128 presets.
1. Set <Mode> in <Sequence setup> to
<Group>.
The menu screen will switch to the group
setting screen.
2. Select a group setting mode.
 Group No. : Select a group number.
 Preset No. : Select a preset number.
 Speed : Specify the speed of movement.
 Dwell time : Specify the duration for which an operation is kept at the preset
position.
] button.
3. Press the [
Your settings will be entered in the right list.
] button.
4. Press the [
Selected group data will be deleted.
To configure the tour settings
The tour function enables you to call groups of your presets in sequence.
1. Set <Mode> in <Sequence setup> to
<Tour>.
The menu screen will switch to the tour
setting screen.
2. Configure the tour settings in detail.
 Group No. : Select a group number.
 Dwell time : Specify a waiting time
before a new group is called.
English _85
● SETUP SCREEN
6. Press the [
setup screen
3. Press the [
] button.
Your settings will be entered in the right list.
4. Press the [
] button.
Set data on the right list will be saved.
] button.
5. Press the [
Selected tour data will be deleted.
To set the tracing function
Tracking remembers the trace of movements instructed using the direction button and
reproduces it for your reference.
1. Set <Mode> in <Sequence setup> to
<Trace & Auto Run>.
The menu screen will switch to the
PTZ tracking and Auto operation menu
screen.
2. Select a tracking number.
You can save the trace in memory
within 120 seconds.
The saving time may differ depending
on the difficulty of the PTZ operation.
The operation will be saved in memory (with the memory status displayed). When
the memory is full and the “EEPROM: 000%” message appears, tracking will be
terminated.
] button.
3. Press the [
Selected tracing number will be saved.
4. Press the [
] button.
Selected tracing number will be activated as set.
] button.
5. Press the [
Tracing will be stop.
86_ setup screen
To set the auto run
This will perform the sequence operation that you have specified if no controller
manipulation is made for a certain time.
2. Select an auto run mode.
 Home : Automatically executes the
operation to the home position.
 Preset : Automatically executes the operation to the preset number.
 Swing : Automatically executes the operation in Swing mode.
 Group : Automatically executes the operation in Group mode.
 Tour : Automatically executes the operation in Tour mode.
 Trace : Automatically executes the operation in Trace mode.
 Auto pan : Automatically executes the 360° rotation in the pan direction.
Auto Pan requires two options that need your settings: tilting angle and pan
speed.
3. Press the [
] button.
PTZ limit
You can specify restrictions on the pan or tilt function.
1. From the Setup menu, select the
)> tab.
<Audio & Video (
2. Click <PTZ limit>.
3. Decide if you want to limit the PTZ
operations. If so, specify the details.
 Pan / Tilt Limit : Select a mode to set
between Pan limit and Tilt limit.
- Use : Select whether to use limit in
set mode.
] : Start limit setting.
- [
- [
] : The starting point will be saved.
- [
] : The ending point will be saved then the limit mode runs in specified range between the start point and end point respectively.
English _87
● SETUP SCREEN
1. Set <Mode> in <Sequence setup> to
<Trace & Auto Run>.
The menu screen will switch to the
PTZ tracking and Auto execution menu
screen.
setup screen
NETWORK SETUP
Interface
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <Interface>.
3. Set the <Interface> and <IPv6 setup>
as necessary.
 IP type : Select an IP connection
type.
- Manual : Specify the IP address,
Subnet Mask, Gateway, DNS1,
and DNS2.
- DHCP : Specify the DNS1 and DNS2.
- PPPoE : Specify the DNS1, DNS2, ID and password.
 If you set it to <Manual>, you should specify the IP, Subnet Mask, Gateway, DNS 1 & 2 manually.







MAC address : Shows the MAC address.
IP address : Displays the current IP address.
Subnet mask : Displays the <Subnet mask> for the set IP.
Gateway : Displays the <Gateway> for the set IP.
DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.
IPv6 use : Specify the use of IPv6.
IPv6 address : Obtains the IPv6 address to access the IPv6 network.
4. When done, click [Apply (
J
)].
 The IP addressing system will be defaulted to DHCP. However, if the DHCP server is still not found
after 1 minute, the IP system will switch to Static automatically.
88_ setup screen
Port
1. From the Setup menu, select the
<Network (
)> tab.
3. Type in each item in the Port menu as
necessary.
 Neither the port range between 0 and 1023
nor port 3702 is available.
 HTTP port : HTTP port used to
access the camera via the web
browser.
The default is 80(TCP).
 VNP port : Set a port used to transfer video signals with the Samsung protocols.
 RTSP port : Used to transfer videos in the RTSP mode; the default is 554.
 Viewer port : Used to transfer videos to the Web Viewer; the default is 4520.
 The port range of the Viewer is between 4502 and 4534. If the VNP port is with this effective range,
the Viewer port should be specified the same as the VNP port.
4. When done, click [Apply (
)].
DDNS
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of
a camera into a general Host Name so that the user can easily remember it.
1. From the Setup menu, select the
<Network (
)> tab.
2. Click <DDNS>.
3. Select <DDNS>.
4. Type in the DDNS items according to
the selected type.
 Samsung DDNS : Select this if you
use the DDNS server provided by
Samsung Techwin.
 Public DDNS : Select one of provided public DDNS servers when you use a public
DDNS server.
- Host name : Enter the name of the host (i.e., host name of Dyndns) that is registered
with the DDNS server.
English _89
● SETUP SCREEN
2. Click <Port>.
setup screen
- User name : Enter the user name for the DDNS service. (i.e., user ID that is
registered with Dyndns)
- Password : Enter the password for the DDNS service. (i.e., password that is
registered with Dyndns)
5. When done, click [Apply (
)].
Registering with DDNS
To register your product with the Samsung DDNS
1. Visit the iPOLiS web site
(www.samsungipolis.com) and sign in
with a registered account.
2. From the top menu bar, select <DDNS
SERVICE>-<MY DDNS>.
3. Click [PRODUCT REGISTRATION].
4. Enter the product domain.
 You must perform the duplicate check for the
domain that you entered.
90_ setup screen
5. Select a <CLASSIFICATION> and
specify the <MODEL NUMBER>.
6. Specify the product location with a
description if necessary.
● SETUP SCREEN
7. Click [REGISTRATION].
The product will be added to the product list that you can check.
To connect to the Samsung DDNS in camera setup
1. From the DDNS setup page, set
<DDNS> to <Samsung DDNS>.
2. Provide the <Host name> that you registered product domain with the DDNS
site.
3. Click [Apply (
)].
When the connection is successfully
made, you will see the message of
<(Success)> on the screen.
Configuring public DDNS in Camera Settings
1. Open the DDNS settings page and select <Public DDNS> for <DDNS>.
2. Enter the corresponding site’s host name, user name and password.
3. Click [Apply (
)] button.
If the connection properly establishes, <(Success)> appears.
4. When done, click [Apply (
)].
English _91
setup screen
IP filtering
You can create a list of IPs that you want to grant or deny access to them.
1. From the Setup menu, select the
)> tab.
<Network (
2. Click <IP filtering>.
3. Select <Filtering type>.
 Deny : If selecting this, access from
those IPs that are added to the
filtering will be restricted.
 Allow : If selecting this, access from
only those IPs that are added to the
filtering will be accepted.
4. Provide the IP that you want to grant or
deny access from.
5. When done, click [Apply (
)].
SSL
You can select a secure connection system or install the public certificate for this purpose.
1. From the Setup menu, select the
)> tab.
<Network (
2. Click <SSL>.
3. Select a secure connection system.
 To access the camera using HTTPS mode, you
have to type the IP address for the camera in
the form of “https://<Camera_IP>”.
4. Search for the public certificate that you
want to install on the camera.
To install the certificate on the camera, you need to provide a certificate name (it can
be arbitrarily assigned by the user), certificate file issued from the certification authority and a key file.
 The <HTTPS(Secure connection mode using the public certificate)> item will be active only if
there exists a public certificate installed.
5. When done, click [Apply (
92_ setup screen
)].
Installing the certificate
1. Enter the certificate name.
2. Select the certificate file to be installed and certificate key, and click [Install (
button.
)]
● SETUP SCREEN
Deleting the certificate
1. Click [Delete (
)] button.
EVENT SETUP
FTP / E-mail
You can configure the FTP/E-mail server settings so that you can transfer the images
stored in the camera to your PC if an event occurs.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <FTP / E-mail>.
3. Select <FTP configuration> or
<E-mail configuration> and enter /
select a desired value.
 FTP configuration
- Server address : Enter the IP address of the FTP server that you
transfer the alarm images to.
- User ID : Enter the user ID with
which you will log in to the FTP
server.
- Password : Enter the user account password for logging into the FTP server.
- Upload directory : Specify the FTP path where you will transfer the alarm
images.
- Port : The default port of the FTP server is 21; however, you can use a different
port number according to the FTP server settings.
- Passive mode : Select <On> if you need to connect in passive mode due to the
firewall or the FTP server settings.
English _93
setup screen
 E-mail configuration
- Server address : Enter the IP address of the email server that you use for the
email transfer.
ex) SMTP. hotmail. com
- Use authentication : Select whether to use authorization.
- User ID : Enter the user ID for logging into the email server.
- Password : Enter the user account password for logging into the email server.
- Port : The default port of the email server is 25; however, you can use a different
port number according to the email server settings.
- Recipient : Enter the address of the email recipient.
- Sender : Enter the address of the email sender. If the sender address is incorrect, the email from the sender may be classified as SPAM by the email server
and thus may not be sent.
- Subject : Enter a subject for your email.
- Body : Provide the text for the massage. Attach the alarm images to the email
that you are preparing.
4. When done, click [Apply (
)].
SD record
You can set the record conditions or the use of recording for the SD memory, check the
size of stored data, or format the SD memory itself.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <SD record>.
94_ setup screen
To make recording on the SD memory
1. Check the <Total size> and the <Free size>.
 For a SD memory card with a large capacity, the formatting will be slowed down accordingly.
 If the size of data grows with time, only 1 fps can be stored even if you set the record quality to Full
Frame.
3. Specify the record conditions.
 Record 1 fps forcibly : Only one frame per second will be recorded regardless of
the existing record profile.
 Overwrite : If the SD memory is full, this will delete old data and store new data in
replacement.
 Pre-alarm duration : Specify the time point before the occurrence of the alarm;
starting from the time point, the images will be transferred. You can specify up to
5 seconds before the occurrence of the alarm.
 Post-alarm duration : Specify the time point after the occurrence of the alarm; to
the specified time point, the images will be transferred. You can specify up to 120
seconds after the occurrence of the alarm.
4. When done, click [Apply (
)].
English _95
● SETUP SCREEN
2. If the SD memory has a sufficient free space, set <Record> to <On>.
Otherwise, check the stored data and if you find them not important, then click
<Format> to format the SD memory.
 If your SD memory card writes slowly, only one frame per second will be stored.
setup screen
Alarm input1/Alarm input2
You can set the alarm input type, activation time, and operation mode.
1. From the Setup menu, select the
)> tab.
<Event (
2. Click <Alarm input>.
3. Specify an input device.
 Type
- Normal Open : It is normally open,
but if it is closed, an alarm will be
triggered.
- Normal Close : It is normally
closed, but if it is open, an alarm
will be triggered.
4. Specify the <Activation time>.
 Always : Always check if an alarm occurs. It activates in operated mode when the
alarm occurs.
 Only scheduled time : Check if an alarm occurs at a specified day of the week for
a specified time period. It activates in operated mode when the alarm occurs.
5. Specify an operation that will perform if an alarm occurs.
 Alarm output1/Alarm output2 : Select whether to set the alarm output if an alarm
is incoming, and specify the alarm output time.
 E-mail sending : Specify the use of email transfer in the alarm input setup.
 Record : Specify the use of recording in the alarm input setup.
 Goto Preset : Moves to the specified preset location when setting the alarm input.
6. When done, click [Apply (
96_ setup screen
)].
Video analysis
1. From the Setup menu, select the
<Event (
)> tab.
● SETUP SCREEN
2. Click <Video analysis>.
3. Specify the use of Intelligent Video
Analysis.
4. Set the resolution value and sensitivity
level to detect an object.
Resolution Value
1
2
3
4
5
Object Size
32 of 8x8 pixel
24 of 8x8 pixel
16 of 8x8 pixel
8 of 8x8 pixel
1 of 8x8 pixel
 If you set the Resolution Value high, the
camera can detect detail motion of the object.
5. Set the Motion Detection type.
Sets to detect and trace the moving
object.
 Tracking : Detects a moving object and perform additional functions.
 Detection : Detects a moving object.
6. Set whether to use the Additional Motion Functions or not.
Detects any motion of an object, displays the video with any changes, and trace the
moving path.
 If you select the <Moved/Fixed>, you can display the corresponding area when
an object disappears from the screen or an object appears and stays in the
screen for a specified time period.
7. Set whether to use the Motion Display function or not.
8. Set the activation time and condition.
 Refer to the "Alarm input1/Alarm input2" for how to set the <Activation time> and <Action>. (page 96)
9. Select whether to display the mask zone.
You can set maximum of 4 mask zones. To set mask area, drag the desigred area
with mouse. Motion detection is not activated in set mask area. To delete set area,
)] button.
click [Delete (
English _97
setup screen
J
 Even if the <Video analysis> is enabled, the video analysis function does not work when
entering through the operating menu in the camera.
 If camera is capturing a close object, the video analysis capability may degrade. In the following
cases, the video analysis function may not produce a proper result on the default event and
motion detections.
-
The object color or brightness is similar to the background
Multiple movements continue occurring at random due to a scene change or other reasons.
A fixed object continues moving in the same position.
An object hides other objects behind.
Two or more objects overlap or one object divides in multiple portions
Too fast object (for a proper detection, one object should be found overlapping between
contiguous frames).
- Reflection / blur / shadow due to a strong light such as direct sunlight, illumination, or headlamp
- In severe snow, rain, wind or in dawn / dusk
- A moving object comes close to the camera
Time schedule
You can configure so that an event will occur at a scheduled time regardless of the actual
occurrence of the event.
1. From the Setup menu, select the
<Event (
)> tab.
2. Click <Time schedule>.
To set the timer event
1. Set <Timer event setup> to <Enable>.
2. Specify the <Activation time>.
 Always : Always activates in operated
mode at the set interval.
 Only scheduled time : Periodically
activates in operated mode at a
specified time and date.
98_ setup screen
3. Specify the <Transfer interval>.
4. Specify the activation conditions.
 FTP sending : Specify the use of the FTP transfer if an event occurs.
 Record : Specify the use of recording if an event occurs.
)].
● SETUP SCREEN
5. When done, click [Apply (
SYSTEM SETUP
Product information
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Product information>.
3. Check the camera information, or
provide details according to your
network environment.
 Location : Specify the location where
the camera is installed.
 Description : Provide detailed
information about the camera location.
 Memo : Provide an explanation about the camera for better understanding.
 Language : Selects the language to display in the Web Viewer.
4. When done, click [Apply (
J
)].
 You should change the camera menu language in camera menu.
 Product related information only allows English for input.
English _99
setup screen
Date & Time
1. From the Setup menu, select the
<System (
)> tab.
2. Click <Date & Time>.
3. Specify the time and date that will be
applied to the camera.
 Current system time : Displays the
current time settings of your system.
 Timezone : Specify the local time
zone based on the GMT.
 Use daylight saving time :
If checked, the time will be set one
hour before the local time zone for the specified time period.
This option will be displayed only in areas where DST is applied.
 System time setup : Specify the time and date that will be applied to your system.
- Manual : Specify the time manually.
- Synchronize with NTP server : Sync with the time of the specified server address.
- Synchronize with PC viewer : Synchronize the time with the connected PC.
4. When done, click [Apply (
J
)].
 If you select the <Synchronize with PC viewer>, the standard timezone should be set the same
as the current timezone in PC.
User
1. From the Setup menu, select the
)> tab.
<System (
2. Click <User>.
3. Provide the necessary user information.
 Administrator Password Change :
Change the current password for the
administrator.
 The default password can be exposed to
a hacking thread so it is recommended to
change the password after installing the
product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.
100_ setup screen
4. When done, click [Apply (
)].
Upgrade / Reboot
1. From the Setup menu, select the
)> tab.
<System (
2. Click <Upgrade / Reboot>.
3. Select a desired item and set it
appropriately.
 Upgrade : Performs upgrading the
system.
 Factory default : Resets the system
to the factory default.
- Except network parameter : Reset
the other settings except for the
interface/port/DDNS/IP filtering/SSL settings.
- All : Resets all settings including the camera settings. (however, the log
information will not be reset)
 If you reset the camera, the network settings will be adjusted so that DHCP can be enabled.
If there is no DHCP server in the network, you must run the IP Installer program to change the basic
network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.
 Configuration backup & Restore : Backs up the current system settings before performing the restoration process. The system is automatically restarts after backup
or restoration.
 Restart : Restarts the system.
English _101
● SETUP SCREEN
 Guest setup : If <Guest access> is permitted, any guest can access the Web
Viewer screen but can view only the Live viewer screen.
 Current users : You can change the user information and adjust the permission
level for a user who is set to <Enable>.
- Video : You can select a video profile in the Liver viewer screen.
- Audio-In : The audio input option will be activated in the Live Viewer screen.
- Controls : You can control the camera menu, PTZ, Mic. and Alarm button.
setup screen
To perform the upgrade
1. Click [Upgrade].
2. Click [Browse] and specify a file to
upgrade.
3. Click [Send].
4. The “Upgrade” dialog appears where
the progression will be shown in the
bottom.
M
 If you forcibly terminate the upgrade
process, upgrade will not be completed
properly.
To save the current settings and restore the backup settings
1. Click [Backup].
The Save As dialog should appear.
2. Specify the backup path with a proper
file name, and click [Save].
The backup file will be saved to the
specified path in the format of “.bin”.
3. To restore the backup settings, click
[Restore].
4. Select a backup file and click [Open].
102_ setup screen
Log
You can check the system log or event log.
● SETUP SCREEN
1. From the Setup menu, select the
)> tab.
<System (
2. Click <Log>.
3. Select a log type.
 Syslog : You can check the system
logs where any system changes are
recorded including the time information.
 Evtlog : You can check the event logs
including the time information.
4. From the right log list, select an item to
search for.
 If you select <All> in the top left
dropdown list, all logs for the applicable log type will be displayed.
5. If one page can not display all the logs available, use the bottom buttons to move to
the previous, next, or the last item.
M
 If you want to view the details of a log, click [Info (
)] in the right column of the log; the log
information will be shown in the bottom pane.
 Each page displays 15 logs with the latest one displayed at the top.
 The event/system log list can contain up to 1000 logs; after that, the existing logs will be deleted
from the oldest one each time a new log is created.
English _103
appendix
SPECIFICATION
Description
Items
Video
SNP-3120
SNP-3120V
SNP-3120VH
Imaging Device
1/4" Ex-view HAD PS CCD
Total Pixels
NT : 811(H) x 508(V), PAL : 795(H) x 596(V)
Effective Pixels
NT : 768(H) x 494(V), PAL : 752(H) x 582(V)
Scanning System
Progressive(VPS ON) (If WDR on, Interlaced Scan)
Synchronization
Internal / Line lock
Frequency
NT : H : 15.734KHz / V : 59.94Hz, PAL : H : 15.625KHz / V : 50Hz
Horizontal Resolution
Color : 600 TV lines
Min. Illumination
Color : 0.7 Lux (F 1.65, 50 IRE, VPS OFF), 0.001 Lux (Sens up 512X)
B/W : 0.07 Lux (F 1.65, 50 IRE, VPS OFF), 0.0001 Lux (Sens up 512X)
S / N Ratio
50dB
Video Out
CVBS : 1.0 Vp-p / 75Ω composite
Focal Length
(Zoom Ratio)
3.69~44.32mm (12X)
Max. Aperture Ratio
F1.65(Wide) / F2.01(Tele)
Angular Field of View
H : 54.44˚(Wide) ~ 4.62˚(Tele) / V : 42.32˚(Wide) ~ 3.58˚(Tele)
Min. Object Distance
0.2m (Wide) / 0.8m (Tele)
Focus Cotrol
AF / One-Shot AF / Manual
Zoom Movement
Speed
-
Lens Type
DC Auto Iris
Mount Type
-
Lens
104_ appendix
Description
Items
SNP-3120VH
Pan Range
360˚ Endless
Pan Speed
Preset : 650˚/sec, Manual : 0.05˚/sec ~120˚/sec (Turbo:200˚/sec)
Tilt Range
-5˚~185˚
Tilt Speed
Preset : 650˚/sec, Manual : 0.05˚/sec ~120˚/sec
Rotate Range
-
Preset
255 ea
Preset Accuracy
±0.1˚
Auto Tracking
-
On Screen Display
Operational
SNP-3120V
NT : English, French, German, Spanish, Italian, Korean, Portuguese
PAL : English, French, German, Spanish, Italian, Chinese, Portuguese
Camera Title
Off / On (Displayed up to 12 characters)
Day & Night
Auto (ICR) / Color / B/W
Backlight
Compensation
Off / BLC / WDR
Wide Dynamic Range
NT : 128X / PAL : 160X
Dynamic Range
XDR (eXtended Dynamic Range) (Off/Low/Medium/High)
Digital Noise Reduction Motion Adaptive 2D+3D Noise Filter (Off/Low/Medium/High)
Digital Image
Stabilization
Off / On
Motion Detection
Yes
Privacy Masking
Off / On (12 Polygonal programmable zones)
Sens-up
(Frame Integration)
Off / Auto (2X ~ 512X)
English _105
● APPENDIX
Pan / Tilt /
Rotate
SNP-3120
appendix
Description
Items
Operational
Network
SNP-3120
SNP-3120V
SNP-3120VH
Gain Control
Off / Low / Medium / High / Manual
White Balance
ATW (In) / ATW (Out) / AWC / Manual
Electronic Shutter
Speed
Off / A.FLK / Manual (1/120 ~ 1/10Ksec)
Digital Zoom
16X
Flip / Mirror
Digital Flip
Profile
-
VPS
Off / On
Intelligent Video
Analytics
Moved / Fixed
PIP
-
Schedule
-
Alarm I/O
Input 2ea / Output 2ea (Relay)
RS-485 Protocol
SAMSUNG T/E, PELCO-P/D, Panasonic, Honeywell, AD, Vicon, GE,
Bosch
Ethernet
RJ-45 (10/100BASE-T)
Video Compression
Format
H.264, MPEG4, MJPEG
Resolution
NT : 704x480, 640x480, 352x240, 320x240
PAL : 704x576, 640x480, 352x288, 320x240
Max. Framerate
NT : 30fps / PAL : 25fps
106_ appendix
Description
Items
SNP-3120
SNP-3120V
SNP-3120VH
H.264/MPEG4 : Compression Level, Target Bitrate Level Control
MJPEG : Quality Level Control
Bitrate Control Method
H.264/MPEG4 : CBR or VBR
MJPEG : VBR
Streaming Capability
Multiple Streaming (Up to 10 Profiles)
Audio I/O
Line in / Line out
Audio Compression
Format
G.711 μ-law
● APPENDIX
Video Quality
Adjustment
Audio Communication 2-Way
IP
IPv4, IPv6
Protocol
TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP, HTTP, HTTPS, SSL,
DHCP, PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP,
DNS, DDNS
Security
HTTPS(SSL) Login Authentication
Digest Login Authentication
IP Address Filtering
User access Log
Streaming Method
Unicast / Multicast
Max. User Access
10 users at Unicast Mode
Memory Slot
SD/SDHC Memory Slot
ONVIF Conformance
Yes
Web Viewer
Supported OS : Windows XP / VISTA / 7, MAC OS
Supported Browser : Internet Explorer 6.0 or Higher, Firefox, Google
Chrome, Apple Safari
Central Management
Software
NET-i viewer
Network
English _107
appendix
Description
Items
Environmental
SNP-3120
SNP-3120V
SNP-3120VH
-10°C ~ +50°C
Operating Temperature
(+14°F ~ +122°F)
/ Humidity
/~90% RH
-50°C ~ +50°C (-58°F ~ +122°F) / ~90% RH
Ingress Protection
IP66
-
Input Voltage / Current 24V AC, hPoE(IEEE802.3at)
Electrical
Power Consumption
Max. 15W
Max. 15W (Heater Off), Max. 45W (Heater On)
Color / Material
Body : Ivory / Plastic
Body : Ivory /
Aluminum (Vandal
Resistance)
Dimension (Ø x H)
Ø174.0 x H168.0 mm Ø165.0 x H165.0 mm Ø200.0 x H203.0 mm
(6.85" x 6.61")
(6.5" x 6.5")
(7.87" x 7.99")
Weight
1.2Kg (2.65 lb)
Mechanical
108_ appendix
1.9Kg (4.19 lb)
Body : Ivory /
Aluminum (Vandal
Resistance),
Sun-Shield Built-in
2.4Kg (5.29 lb)
PRODUCT OVERVIEW
❖ SNP-3120
● APPENDIX
0.0
108.0
168.0
R6
Ø174.0 (Max)
❖ SNP-3120V
zhtz|un
165.0
102.5
Ø165.0
0.0
R6
English _109
appendix
zhtz|un
0.0
R6
Ø200.0
110_ appendix
203.0
184.0
120.0
19.0
❖ SNP-3120VH
TROUBLESHOOTING
PROBLEM
SOLUTION
y Check to make sure that all network cables have been connected
properly.
I can’t access the camera from a
web browser.
y If connected using DHCP, verify that the camera is able to acquire
dynamic IP addresses without any problem.
y If connected using a DDNS URL, verify that the MAC address has been
properly entered.
y If the camera is connected to a router, verify that port forwarding is
properly configured.
y Connected Viewers become disconnected upon any change to camera or
network configurations.
Viewer got disconnected during
monitoring.
y Check all network connections.
I cannot connect to the system
using a tab browser of Internet
Explorer 7.0.
y When you try to connect to the system using a tab browser, the same
cookie information is shared, resulting in errors when connected.
Therefore, instead of using a tab browser, open a new browser window
to connect to the system.
The camera connected to the
network is not detected in the IP
installer program.
y Turn off the firewall settings on your PC and then search the camera
again.
Images overlap.
y Check whether two or more cameras are set to a single multicast address
instead of different addresses. If a single address is used for multiple
cameras, the images may overlap.
No image appears.
y If the transmission method is set to multicast, check whether there is a
router that supports multicast in the LAN the camera is connected to.
y If the camera is connected over an PPPoE network, it’ s possible for
Viewer to disconnect under poor network conditions.
English _111
● APPENDIX
y Check to make sure that the camera’s Network settings are appropriate.
appendix
PROBLEM
SOLUTION
No JPEG file is transferred via
e-mail on occurrence of intelligent
video analysis event of camera
even when the <IV analysis
function> is set to <Enable>.
y Verify the settings in the following sequence:
Can <Set Rules> be configured
even when the <IV analysis
function> is set to <Disable>?
y Yes, it can be. You can set rules for events despite of the intelligent
video analysis setting.
No signal is found at the Alarm
Output port even when an
intelligent video analysis event is
generated.
y Check alarm output port settings.
A. Check <Data & Time> settings.
B. The <IV analysis function> should be set to <Enable>.
C. Alarm Video Transmission must be enabled.
Cannot record into the SD memory y Check if the memory card is defective.
card.
y Check if the write protection tab of the memory card is set to “LOCK”.
SD memory card is inserted but
the camera does not operate
properly.
Cannot format the SD memory
card.
112_ appendix
y Check if the memory card is inserted in the proper direction. Operation
of memory card that is formatted by other devices is not guaranteed with
this camera unit
y Format the memory card again in <Setup>  <Event>  <SD Record>
menu.
y Check if the write protection tab of the memory card is set to “LOCK”.
OPEN SOURCE ANNOUNCEMENT
Some software components of this product incorporate source code covered under the BSD
license as follows.
Component Name
License
License URL
lighttpd 1.4.25
librtp 1.20
BSD 2.0
BSD 1.0
http://www.opensource.org/licenses/bsd-license.html
lighttpd is a secure, fast, compliant, and very flexible web-server that has been optimized for
high-performance environments. It has a very low memory footprint compared to other
webservers and takes care of cpu-load. Its advanced feature-set (FastCGI, CGI, Auth,
Output-Compression, URL-Rewriting and many more) make lighttpd the perfect webserversoftware for every server that suffers load problems.
For more additional information, send email to help.cctv@samsung.com.
Copyright (C) 2004, Kneschke, incremental
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted
provided that the following conditions are met :
- Redistributions of source code must retain the above copyright notice, this list of conditions and
the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice, this list of conditions
and the following disclaimer in the documentation and/or other materials provided with the
distribution.
- Neither the name of the 'incremental' nor the names of its contributors may be used to endorse
or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 1998-2001 University College London
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, is permitted
provided that the following conditions are met :
1. Redistributions of source code must retain the above copyright notice, this list of conditions
and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions
and the following disclaimer in the documentation and/or other materials provided with the
distribution.
3. All advertising materials mentioning features or use of this software must display the following
acknowledgement: This product includes software developed by the Computer Science
Department at University College London.
4. Neither the name of the University nor of the Department may be used to endorse or promote
products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHORS AND CONTRIBUTORS ``AS IS'' AND ANY
EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSEARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHORS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
GPL/LGPL SOFTWARE LICENSE
The software included in this product contains copyrighted software that is licensed
under the GPL/LGPL. You may obtain the complete Corresponding Source code from
us for a period of three years after our last shipment of this product by sending email to
help.cctv@samsung.com
If you want to obtain the complete Corresponding Source code in the physical medium
such as CD-ROM, the cost of physically performing source distribution might be charged.
 GPL S/W
- Base Kernel, Busybox, Sysvinit, dosfstools
 LGPL S/W
- gLibc, Inetutils
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C)1989, 1991 Free Software
Foundation, Inc.
51 Franklin Street,Fifth Floor, Boston,
MA 02110-1301, USA
Everyone is permitted to copy and
distribute verbatim copies of this license
document, but changing it is not allowed.
Preamble
The licenses for most software are designed
to take away your freedom to share and
change it. By contrast, the GNU General
Public License is intended to guarantee
your freedom to share and change free
software-- to make sure the software is free
for all its users.
This General Public License applies to most
of the Free Software Foundation's software
and to any other program whose authors
commit to using it. (Some other Free Software
Foundation software is covered by the GNU
Lesser General Public License instead.) You
can apply it to your programs, too.
When we speak of free software, we are
referring to freedom, not price.
Our General Public Licenses are designed
to make sure that you have the freedom
to distribute copies of free software (and
charge for this service if you wish), that you
receive source code or can get it if you
want it, that you can change the software
or use pieces of it in new free programs ;
and that you know you can do these things.
To protect your rights, we need to make
restrictions that forbid anyone to deny you
these rights or to ask you to surrender the
rights. These restrictions translate to certain
responsibilities for you if you distribute
copies of the software, or if you modify it.
For example, if you distribute copies of
such a program, whether gratis or for a fee,
you must give the recipients all the rights
that you have.
You must make sure that they, too, receive or
can get the source code. And you must show
them these terms so they know their rights.
We protect your rights with two steps :
(1)copyright the software, and (2)offer
you this license which gives you legal
permission to copy, distribute and/or
modify the software.
Also, for each author's protection and ours,
we want to make certain that everyone
understands that there is no warranty for
this free software. If the software is modified
by someone else and passed on, we want
its recipients to know that what they have
is not the original, so that any problems
introduced by others will not reflect on the
original authors' reputations.
Finally, any free program is threatened
constantly by software patents. We wish
to avoid the danger that redistributors of a
free program will individually obtain patent
licenses, in effect making the program
proprietary. To prevent this, we have made
it clear that any patent must be licensed for
everyone's free use or not licensed at all.
The precise terms and conditions for
copying, distribution and modification follow.
TERMS AND CONDITIONS FOR
COPYING, DISTRIBUTION AND
MODIFICATION
Version 2, June 1991 Copyright (C) 1989,
1991 Free Software Foundation, Inc. 51
Franklin S
0. This License applies to any program
or other work which contains a notice
placed by the copyright holder saying it
may be distributed under the terms of
this General Public License.
The "Program", below, refers to any such
program or work, and a "work based on
the Program" means either the Program
or any derivative work under copyright
law : that is to say, a work containing the
Program or a portion of it, either verbatim
or with modifications and/or translated
into another language. (Hereinafter,
translation is included without limitation
in the term "modification".) Each licensee
is addressed as "you".
Activities other than copying, distribution
and modification are not covered by
this License ; they are outside its scope.
The act of running the Program is not
restricted, and the output from the
Program is covered only if its contents
constitute a work based on the Program
(independent of having been made by
running the Program). Whether that is
true depends on what the Program does.
1. You may copy and distribute verbatim
copies of the Program's source code as
you receive it, in any medium, provided
that you conspicuously and appropriately
publish on each copy an appropriate
copyright notice and disclaimer of
warranty; keep intact all the notices that
refer to this License and to the absence
of any warranty ; and give any other
recipients of the Program a copy of this
License along with the Program.
You may charge a fee for the physical
act of transferring a copy, and you may
at your option offer warranty protection
in exchange for a fee.
2. You may modify your copy or copies
of the Program or any portion of it,
thus forming a work based on the
Program, and copy and distribute such
modifications or work under the terms of
Section 1 above, provided that you also
meet all of these conditions :
a) You must cause the modified files to
carry prominent notices stating that
you changed the files and the date of
any change.
b) You must cause any work that you
distribute or publish, that in whole or
in part contains or is derived from the
Program or any part thereof, to be
licensed as a whole at no charge to
all third parties under the terms of this
License.
c) If the modified program normally
reads commands interactively
when run,you must cause it, when
started running for such interactive
use in the most ordinary way, to
print or display an announcement
including an appropriate copyright
notice and a notice that there is no
warranty (or else, saying that you
provide a warranty) and that users
may redistribute the program under
these conditions, and telling the user
how to view a copy of this License.
(Exception:if the Program itself is
interactive but does not normally print
such an announcement, your work
based on the Program is not required
to print an announcement.)
These requirements apply to the modified
work as a whole. If identifiable sections
of that work are not derived from
the Program, and can be reasonably
considered independent and separate
works in themselves, then this License, and
its terms, do not apply to those sections
when you distribute them as separate
works. But when you distribute the same
sections as part of a whole which is a work
based on the Program, the distribution
of the whole must be on the terms of this
License, whose permissions for other
licensees extend to the entire whole, and
thus to each and every part regardless of
who wrote it.
Thus, it is not the intent of this section to
claim rights or contest your rights to work
written entirely by you ; rather, the intent is to
exercise the right to control the distribution
of derivative or collective works based on
the Program. In addition, mere aggregation
of another work not based on the Program
with the Program (or with a work based on
the Program)on a volume of a storage or
distribution medium does not bring the other
work under the scope of this License.
3. You may copy and distribute the
Program (or a work based on it, under
Section 2)in object code or executable
form under the terms of Sections 1 and
2 above provided that you also do one of
the following :
a) Accompany it with the complete
corresponding machine-readable
source code, which must be
distributed under the terms of
Sections 1 and 2 above on a medium
customarily used for software
interchange ; or,
b) Accompany it with a written offer,
valid for at least three years, to give
any third party, for a charge no
more than your cost of physically
performing source distribution, a
complete machinereadable copy
of the corresponding source code,
to be distributed under the terms
of Sections 1 and 2 above on a
medium customarily used for software
interchange ; or,
c) Accompany it with the information
you received as to the offer to
distribute corresponding source code.
(This alternative is allowed only for
noncommercial distribution and only
if you received the program in object
code or executable form with such
an offer, in accord with Subsection b
above.)
The source code for a work means the
preferred form of the work for making
modifications to it. For an executable work,
complete source code means all the source
code for all modules it contains, plus any
associated interface definition files, plus
the scripts used to control compilation and
installation of the executable. However,
as a special exception, the source code
distributed need not include anything that
is normally distributed (in either source or
binary form)with the major components
(compiler, kernel, and so on)of the operating
system on which the executable runs,
unless that component itself accompanies
the executable.
If distribution of executable or object code
is made by offering access to copy from a
designated place, then offering equivalent
access to copy the source code from the
same place counts as distribution of the
source code, even though third parties are
not compelled to copy the source along
with the object code.
4. You may not copy, modify, sublicense,
or distribute the Program except as
expressly provided under this License.
Any attempt otherwise to copy, modify,
sublicense or distribute the Program is
void, and will automatically terminate
your rights under this License.
However, parties who have received
copies, or rights, from you under this
License will not have their licenses
terminated so long as such parties
remain in full compliance.
5. You are not required to accept this
License, since you have not signed it.
However, nothing else grants you
permission to modify or distribute the
Program or its derivative works.
These actions are prohibited by law if you
do not accept this License.Therefore, by
modifying or distributing the Program (or
any work based on the Program), you
indicate your acceptance of this License
to do so, and all its terms and conditions
for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program
(or any work based on the Program),
the recipient automatically receives a
license from the original licensor to copy,
distribute or modify the Program subject
to these terms and conditions.
You may not impose any further
restrictions on the recipients' exercise of
the rights granted herein.
You are not responsible for enforcing
compliance by third parties to this
License.
7. If, as a consequence of a court judgment
or allegation of patent infringement or for
any other reason (not limited to patent
issues), conditions are imposed on you
(whether by court order, agreement or
otherwise)that contradict the conditions
of this License, they do not excuse you
from the conditions of this License. If
you cannot distribute so as to satisfy
simultaneously your obligations under
this License and any other pertinent
obligations, then as a consequence you
may not distribute the Program at all.
For example, if a patent license would
not permit royalty-free redistribution of
the Program by all those who receive
copies directly or indirectly through you,
then the only way you could satisfy both
it and this License would be to refrain
entirely from distribution of the Program.
If any portion of this section is held invalid
or unenforceable under any particular
circumstance, the balance of the section
is intended to apply and the section as
a whole is intended to apply in other
circumstances. It is not the purpose of
this section to induce you to infringe any
patents or other property right claims or
to contest validity of any such claims; this
section has the sole purpose of protecting
the integrity of the free software distribution
system, which is implemented by public
license practices. Many people have made
generous contributions to the wide range
of software distributed through that system
in reliance on consistent application of that
system ; it is up to the author/donor to
decide if he or she is willing to distribute
software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly
clear what is believed to be a consequence
of the rest of this License.
8. If the distribution and/or use of the
Program is restricted in certain countries
either by patents or by copyrighted
interfaces, the original copyright holder
who places the Program under this
License may add an explicit geographical
distribution limitation excluding those
countries,so that distribution is permitted
only in or among countries not thus
excluded. In such case, this License
incorporates the limitation as if written in
the body of this License.
9. The Free Software Foundation may
publish revised and/or new versions of
the General Public License from time to
time. Such new versions will be similar
in spirit to the present version, but may
differ in detail to address new problems
or concerns.
Each version is given a distinguishing
version number. If the Program specifies
a version number of this License which
applies to it and "any later version", you
have the option of following the terms and
conditions either of that version or of any
later version published by the Free Software
Foundation. If the Program does not specify
a version number of this License, you may
choose any version ever published by the
Free Software Foundation.
10. If you wish to incorporate parts of the
Program into other free programs
whose distribution conditions are
different, write to the author to ask
for permission. For software which
is copyrighted by the Free Software
Foundation,write to the Free Software
Foundation ; we sometimes make
exceptions for this. Our decision will be
guided by the two goals of preserving
the free status of all derivatives of our
free software and of promoting the
sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS
LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR
THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN
WRITING THE COPYRIGHT HOLDERS
AND/OR OTHER PARTIES PROVIDE
THE PROGRAM "ASIS" WITHOUT
WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD
THE PROGRAMPROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR
CORRECTION.
12. IN NO EVENT UNLESS REQUIRED
BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE DAMAGES,
INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU
OR THIRD PARTIES OR A FAILURE
OF THE PROGRAM TO OPERATE
WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your
New Programs
If you develop a new program, and you
want it to be of the greatest possible use to
the public, the best way to achieve this is to
make it free software which everyone can
redistribute and change under these terms.
To do so, attach the following notices to
the program. It is safest to attach them
to the start of each source file to most
effectively convey the exclusion of warranty
; and each file should have at least the
"copyright" line and a pointer to where the
full notice is found.
one line to give the program's name and an
idea of what it does.
Copyright (C)yyyy name of author
This program is free software ; you can
redistribute it and/or modify it under the
terms of the GNU General Public License as
published by the Free Software Foundation
; either version 2 of the License, or (at your
option)any later version.
This program is distributed in the hope
that it will be useful, but WITHOUT ANY
WARRANTY ; without even the implied
warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.
See the GNU General Public License for
more details.
You should have received a copy of the
GNU General Public License along with this
program ; if not, write to the Free Software
Foundation, Inc.,51 Franklin Street, Fifth
Floor, Boston, MA 02110-1301, USA.
Also add information on how to contact you
by electronic and paper mail. If the program
is interactive, make it output a short notice
like this when it starts in an interactive
mode :
program is a subroutine library, you may
consider it more useful to permit linking
proprietary applications with the library. If
this is what you want to do, use the GNU
Lesser General Public License instead of
this License.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation,
Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute
verbatim copies of this license document, but
changing it is not allowed.
Gnomovision version 69,
Preamble
Copyright (C) year name of author
The GNU General Public License is a free,
copyleft
Gnomovision comes with ABSOLUTELY
NO
WARRANTY ; for details type ‘show w’.
This is free software, and you are welcome
to redistribute it under certain conditions ;
type ‘show c’ for details.
The hypothetical commands ‘show w’ and
‘show c’ should show the appropriate parts
of the General Public License. Of course,
the commands you use may be called
something other than ‘show w’ and ‘show
c’ ; they could even be mouse-clicks or
menu items-- whatever suits your program.
You should also get your employer (if you
work as a programmer)or your school, if
any, to sign a "copyright disclaimer" for the
program,if necessary. Here is a sample ;
alter the names:
Yoyodyne, Inc.,hereby disclaims all
copyright interest in the program ‘
Gnomovision’ (which makes passes at
compilers) written by James Hacker.
signature of Ty Coon, 1 April 1989 Ty
Coon, President of Vice This General Public
License does not permit incorporating your
program into proprietary programs. If your
license for software and other kinds of
works. The licenses for most software and
other practical works are designed to take
away your freedom to share and change
the works. By contrast, the GNU General
Public License is intended to guarantee
your freedom to share and change all
versions of a program--to make sure it
remains free software for all its users.
We, the Free Software Foundation, use
the GNU General Public License for most
of our software; it applies also to any other
work released this way by its authors.
You can apply it to your programs, too.
When we speak of free software, we are
referring to freedom, not price. Our General
Public Licenses are designed to make sure
that you have the freedom to distribute
copies of free software (and charge for
them if you wish), that you receive source
code or can get it if you want it, that you
can change the software or use pieces of
it in new free programs, and that you know
you can do these things.
To protect your rights, we need to prevent
others from denying you these rights
or asking you to surrender the rights.
Therefore, you have certain responsibilities
if you distribute copies of the software, or if
you modify it: responsibilities to respect the
freedom of others.
For example, if you distribute copies of
such a program, whether gratis or for a
fee, you must pass on to the recipients
the same freedoms that you received. You
must make sure that they, too, receive or
can get the source code. And you must
show them these terms so they know their
rights.
Developers that use the GNU GPL protect
your rights with two steps: (1) assert
copyright on the software, and (2) offer you
this License giving you legal permission to
copy, distribute and/or modify it.
For the developers' and authors'
protection, the GPL clearly explains that
there is no warranty for this free software.
For both users' and authors' sake, the GPL
requires that modified versions be marked
as changed, so that their problems will
not be attributed erroneously to authors of
previous versions.
Some devices are designed to deny users
access to install or run modified versions
of the software inside them, although
the manufacturer can do so. This is
fundamentally incompatible with the aim
of protecting users' freedom to change
the software. The systematic pattern of
such abuse occurs in the area of products
for individuals to use, which is precisely
where it is most unacceptable. Therefore,
we have designed this version of the GPL
to prohibit the practice for those products.
If such problems arise substantially in
other domains, we stand ready to extend
this provision to those domains in future
versions of the GPL, as needed to protect
the freedom of users.
Finally, every program is threatened
constantly by software patents. States
should not allow patents to restrict
development and use of software on
general-purpose computers, but in those
that do, we wish to avoid the special danger
that patents applied to a free program
could make it effectively proprietary. To
prevent this, the GPL assures that patents
cannot be used to render the program nonfree.
The precise terms and conditions for
copying, distribution and modification
follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU
General Public License.
“Copyright” also means copyright-like laws
that apply to other kinds of works, such as
semiconductor masks.
“The Program” refers to any copyrightable
work licensed under this License. Each
licensee is addressed as “you”. “Licensees”
and “recipients” may be individuals or
organizations.
To “modify” a work means to copy from
or adapt all or part of the work in a fashion
requiring copyright permission, other than the
making of an exact copy. The resulting work
is called a “modified version” of the earlier
work or a work “based on” the earlier work.
A “covered work” means either the unmodified
Program or a work based on the Program.
To “propagate” a work means to do anything
with it that, without permission, would
make you directly or secondarily liable for
infringement under applicable copyright
law, except executing it on a computer
or modifying a private copy. Propagation
includes copying, distribution (with or without
modification), making available to the public,
and in some countries other activities as well.
To “convey” a work means any kind of
propagation that enables other parties to
make or receive copies. Mere interaction with
a user through a computer network, with no
transfer of a copy, is not conveying.
An interactive user interface displays
“Appropriate Legal Notices” to the extent
that it includes a convenient and prominently
visible feature that (1) displays an appropriate
copyright notice, and (2) tells the user that
there is no warranty for the work (except
to the extent that warranties are provided),
that licensees may convey the work under
this License, and how to view a copy of this
License. If the interface presents a list of user
commands or options, such as a menu, a
prominent item in the list meets this criterion.
1. Source Code.
The “source code” for a work means the
preferred form of the work for making
modifications to it. “Object code” means any
non-source form of a work.
A “Standard Interface” means an interface
that either is an official standard defined
by a recognized standards body, or, in the
case of interfaces specified for a particular
programming language, one that is widely
used among developers working in that
language.
The “System Libraries” of an executable
work include anything, other than the work
as a whole, that (a) is included in the normal
form of packaging a Major Component, but
which is not part of that Major Component,
and (b) serves only to enable use of the
work with that Major Component, or to
implement a Standard Interface for which
an implementation is available to the public
in source code form. A “Major Component”,
in this context, means a major essential
component (kernel, window system, and so
on) of the specific operating system (if any) on
which the executable work runs, or a compiler
used to produce the work, or an object code
interpreter used to run it.
The “Corresponding Source” for a work
in object code form means all the source
code needed to generate, install, and (for
an executable work) run the object code
and to modify the work, including scripts
to control those activities. However, it does
not include the work's System Libraries, or
general-purpose tools or generally available
free programs which are used unmodified in
performing those activities but which are not
part of the work. For example, Corresponding
Source includes interface definition files
associated with source files for the work,
and the source code for shared libraries and
dynamically linked subprograms that the work
is specifically designed to require, such as by
intimate data communication or control flow
between those subprograms and other parts
of the work.
The Corresponding Source need not
include anything that users can regenerate
automatically from other parts of the
Corresponding Source.
The Corresponding Source for a work in
source code form is that same work.
2. Basic Permissions.
All rights granted under this License are
granted for the term of copyright on the
Program, and are irrevocable provided the
stated conditions are met. This License
explicitly affirms your unlimited permission to
run the unmodified Program. The output from
running a covered work is covered by this
License only if the output, given its content,
constitutes a covered work. This License
acknowledges your rights of fair use or other
equivalent, as provided by copyright law.
You may make, run and propagate covered
works that you do not convey, without
conditions so long as your license otherwise
remains in force. You may convey covered
works to others for the sole purpose of having
them make modifications exclusively for you,
or provide you with facilities for running those
works, provided that you comply with the
terms of this License in conveying all material
for which you do not control copyright. Those
thus making or running the covered works for
you must do so exclusively on your behalf,
under your direction and control, on terms
that prohibit them from making any copies
of your copyrighted material outside their
relationship with you.
Conveying under any other circumstances is
permitted solely under the conditions stated
below. Sublicensing is not allowed; section 10
makes it unnecessary.
3. Protecting Users' Legal Rights From
Anti-Circumvention Law.
No covered work shall be deemed part of an
effective technological measure under any
applicable law fulfilling obligations under article
11 of the WIPO copyright treaty adopted on
20 December 1996, or similar laws prohibiting
or restricting circumvention of such measures.
When you convey a covered work, you waive
any legal power to forbid circumvention of
technological measures to the extent such
circumvention is effected by exercising rights
under this License with respect to the covered
work, and you disclaim any intention to limit
operation or modification of the work as a
means of enforcing, against the work's users,
your or third parties' legal rights to forbid
circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the
Program's source code as you receive it, in
any medium, provided that you conspicuously
and appropriately publish on each copy an
appropriate copyright notice; keep intact
all notices stating that this License and any
non-permissive terms added in accord with
section 7 apply to the code; keep intact all
notices of the absence of any warranty; and
give all recipients a copy of this License along
with the Program.
You may charge any price or no price for
each copy that you convey, and you may offer
support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the
Program, or the modifications to produce it
from the Program, in the form of source code
under the terms of section 4, provided that
you also meet all of these conditions:
a) The work must carry prominent notices
stating that you modified it, and giving a
relevant date.
b) The work must carry prominent notices
stating that it is released under this License
and any conditions added under section 7.
This requirement modifies the requirement
in section 4 to “keep intact all notices”.
c) You must license the entire work, as a
whole, under this License to anyone who
comes into possession of a copy. This
License will therefore apply, along with
any applicable section 7 additional terms,
to the whole of the work, and all its parts,
regardless of how they are packaged. This
License gives no permission to license
the work in any other way, but it does
not invalidate such permission if you have
separately received it.
d) If the work has interactive user interfaces,
each must display Appropriate Legal
Notices; however, if the Program has
interactive interfaces that do not display
Appropriate Legal Notices, your work need
not make them do so.
A compilation of a covered work with other
separate and independent works, which are
not by their nature extensions of the covered
work, and which are not combined with it
such as to form a larger program, in or on a
volume of a storage or distribution medium, is
called an “aggregate” if the compilation and
its resulting copyright are not used to limit
the access or legal rights of the compilation's
users beyond what the individual works
permit. Inclusion of a covered work in an
aggregate does not cause this License to
apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object
code form under the terms of sections 4 and 5,
provided that you also convey the machinereadable Corresponding Source under the
terms of this License, in one of these ways:
a) Convey the object code in, or embodied
in, a physical product (including a physical
distribution medium), accompanied by the
Corresponding Source fixed on a durable
physical medium customarily used for
software interchange.
b) Convey the object code in, or embodied
in, a physical product (including a physical
distribution medium), accompanied by a
written offer, valid for at least three years
and valid for as long as you offer spare
parts or customer support for that product
model, to give anyone who possesses
the object code either (1) a copy of the
Corresponding Source for all the software
in the product that is covered by this
License, on a durable physical medium
customarily used for software interchange,
for a price no more than your reasonable
cost of physically performing this conveying
of source, or (2) access to copy the
Corresponding Source from a network
server at no charge.
c) Convey individual copies of the object
code with a copy of the written offer to
provide the corresponding Source. This
alternative is allowed only occasionally and
noncommercially, and only if you received
the object code with such an offer, in
accord with subsection 6b.
d) Convey the object code by offering access
from a designated place (gratis or for a
charge), and offer equivalent access to
the Corresponding Source in the same
way through the same place at no further
charge. You need not require recipients
to copy the Corresponding Source along
with the object code. If the place to copy
the object code is a network server,
the Corresponding Source may be on
a different server (operated by you or
a third party) that supports equivalent
copying facilities, provided you maintain
clear directions next to the object code
saying where to find the Corresponding
Source. Regardless of what server hosts
the Corresponding Source, you remain
obligated to ensure that it is available
for as long as needed to satisfy these
requirements.
e) Convey the object code using peer-topeer transmission, provided you inform
other peers where the object code and
Corresponding Source of the work are
being offered to the general public at no
charge under subsection 6d.
A separable portion of the object code,
whose source code is excluded from the
Corresponding Source as a System Library,
need not be included in conveying the object
code work.
A “User Product” is either (1) a “consumer
product”, which means any tangible personal
property which is normally used for personal,
family, or household purposes, or (2) anything
designed or sold for incorporation into a
dwelling. In determining whether a product is
a consumer product, doubtful cases shall be
resolved in favor of coverage. For a particular
product received by a particular user,
“normally used” refers to a typical or common
use of that class of product, regardless of
the status of the particular user or of the way
in which the particular user actually uses, or
expects or is expected to use, the product.
A product is a consumer product regardless
of whether the product has substantial
commercial, industrial or non-consumer uses,
unless such uses represent the only significant
mode of use of the product.
“Installation Information” for a User
Product means any methods, procedures,
authorization keys, or other information
required to install and execute modified
versions of a covered work in that User
Product from a modified version of its
Corresponding Source. The information
must suffice to ensure that the continued
functioning of the modified object code is in
no case prevented or interfered with solely
because modification has been made.
If you convey an object code work under this
section in, or with, or specifically for use in,
a User Product, and the conveying occurs
as part of a transaction in which the right of
possession and use of the User Product is
transferred to the recipient in perpetuity or for
a fixed term (regardless of how the transaction
is characterized), the Corresponding Source
conveyed under this section must be
accompanied by the Installation Information.
But this requirement does not apply if neither
you nor any third party retains the ability
to install modified object code on the User
Product (for example, the work has been
installed in ROM).
The requirement to provide Installation
Information does not include a requirement to
continue to provide support service, warranty,
or updates for a work that has been modified
or installed by the recipient, or for the User
Product in which it has been modified or
installed. Access to a network may be
denied when the modification itself materially
and adversely affects the operation of the
network or violates the rules and protocols for
communication across the network.
Corresponding Source conveyed, and
Installation Information provided, in accord with
this section must be in a format that is publicly
documented (and with an implementation
available to the public in source code form),
and must require no special password or key
for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that
supplement the terms of this License by
making exceptions from one or more of its
conditions. Additional permissions that are
applicable to the entire Program shall be
treated as though they were included in this
License, to the extent that they are valid under
applicable law. If additional permissions apply
only to part of the Program, that part may be
used separately under those permissions,
but the entire Program remains governed by
this License without regard to the additional
permissions.
When you convey a copy of a covered work,
you may at your option remove any additional
permissions from that copy, or from any part
of it. (Additional permissions may be written
to require their own removal in certain cases
when you modify the work.) You may place
additional permissions on material, added by
you to a covered work, for which you have or
can give appropriate copyright permission.
Notwithstanding any other provision of this
License, for material you add to a covered
work, you may (if authorized by the copyright
holders of that material) supplement the terms
of this License with terms:
a) Disclaiming warranty or limiting liability
differently from the terms of sections 15
and 16 of this License; or
b) Requiring preservation of specified
reasonable legal notices or author
attributions in that material or in the
Appropriate Legal Notices displayed by
works containing it; or
c) Prohibiting misrepresentation of the origin
of that material, or requiring that modified
versions of such material be marked in
reasonable ways as different from the
original version; or
d) Limiting the use for publicity purposes
of names of licensors or authors of the
material; or
e) Declining to grant rights under trademark
law for use of some trade names,
trademarks, or service marks; or
f) Requiring indemnification of licensors and
authors of that material by anyone who
conveys the material (or modified versions
of it) with contractual assumptions of liability
to the recipient, for any liability that these
contractual assumptions directly impose on
those licensors and authors.
All other non-permissive additional terms
are considered “further restrictions” within
the meaning of section 10. If the Program
as you received it, or any part of it, contains
a notice stating that it is governed by this
License along with a term that is a further
restriction, you may remove that term. If a
license document contains a further restriction
but permits relicensing or conveying under
this License, you may add to a covered
work material governed by the terms of that
license document, provided that the further
restriction does not survive such relicensing or
conveying.
If you add terms to a covered work in accord
with this section, you must place, in the
relevant source files, a statement of the
additional terms that apply to those files, or a
notice indicating where to find the applicable
terms.
Additional terms, permissive or nonpermissive, may be stated in the form of
a separately written license, or stated as
exceptions; the above requirements apply
either way.
8. Termination.
You may not propagate or modify a covered
work except as expressly provided under this
License. Any attempt otherwise to propagate
or modify it is void, and will automatically
terminate your rights under this License
(including any patent licenses granted under
the third paragraph of section 11).
from the original licensors, to run, modify
and propagate that work, subject to this
License. You are not responsible for enforcing
compliance by third parties with this License.
However, if you cease all violation of this
License, then your license from a particular
copyright holder is reinstated (a) provisionally,
unless and until the copyright holder explicitly
and finally terminates your license, and (b)
permanently, if the copyright holder fails to
notify you of the violation by some reasonable
means prior to 60 days after the cessation.
An “entity transaction” is a transaction
transferring control of an organization, or
substantially all assets of one, or subdividing
an organization, or merging organizations.
If propagation of a covered work results
from an entity transaction, each party to that
transaction who receives a copy of the work
also receives whatever licenses to the work
the party's predecessor in interest had or
could give under the previous paragraph, plus
a right to possession of the Corresponding
Source of the work from the predecessor in
interest, if the predecessor has it or can get it
with reasonable efforts.
Moreover, your license from a particular
copyright holder is reinstated permanently
if the copyright holder notifies you of the
violation by some reasonable means, this
is the first time you have received notice of
violation of this License (for any work) from
that copyright holder, and you cure the
violation prior to 30 days after your receipt of
the notice.
Termination of your rights under this section
does not terminate the licenses of parties
who have received copies or rights from you
under this License. If your rights have been
terminated and not permanently reinstated,
you do not qualify to receive new licenses for
the same material under section 10.
9. Acceptance Not Required for Having
Copies.
You are not required to accept this License
in order to receive or run a copy of the
Program. Ancillary propagation of a covered
work occurring solely as a consequence of
using peer-to-peer transmission to receive a
copy likewise does not require acceptance.
However, nothing other than this License
grants you permission to propagate or modify
any covered work. These actions infringe
copyright if you do not accept this License.
Therefore, by modifying or propagating a
covered work, you indicate your acceptance
of this License to do so.
10. Automatic Licensing of Downstream
Recipients.
Each time you convey a covered work, the
recipient automatically receives a license
You may not impose any further restrictions
on the exercise of the rights granted or
affirmed under this License. For example, you
may not impose a license fee, royalty, or other
charge for exercise of rights granted under
this License, and you may not initiate litigation
(including a cross-claim or counterclaim in
a lawsuit) alleging that any patent claim is
infringed by making, using, selling, offering for
sale, or importing the Program or any portion
of it.
11. Patents.
A “contributor” is a copyright holder who
authorizes use under this License of the
Program or a work on which the Program is
based. The work thus licensed is called the
contributor's “contributor version”.
A contributor's “essential patent claims” are
all patent claims owned or controlled by the
contributor, whether already acquired or
hereafter acquired, that would be infringed
by some manner, permitted by this License,
of making, using, or selling its contributor
version, but do not include claims that would
be infringed only as a consequence of further
modification of the contributor version. For
purposes of this definition, “control” includes
the right to grant patent sublicenses in a
manner consistent with the requirements of
this License.
Each contributor grants you a non-exclusive,
worldwide, royalty-free patent license under
the contributor's essential patent claims, to
make, use, sell, offer for sale, import and
otherwise run, modify and propagate the
contents of its contributor version.
In the following three paragraphs, a “patent
license” is any express agreement or
commitment, however denominated, not
to enforce a patent (such as an express
permission to practice a patent or covenant
not to sue for patent infringement). To “grant”
such a patent license to a party means to
make such an agreement or commitment not
to enforce a patent against the party.
If you convey a covered work, knowingly
relying on a patent license, and the
Corresponding Source of the work is not
available for anyone to copy, free of charge
and under the terms of this License, through
a publicly available network server or other
readily accessible means, then you must
either (1) cause the Corresponding Source
to be so available, or (2) arrange to deprive
yourself of the benefit of the patent license
for this particular work, or (3) arrange, in a
manner consistent with the requirements of
this License, to extend the patent license to
downstream recipients. “Knowingly relying”
means you have actual knowledge that, but
for the patent license, your conveying the
covered work in a country, or your recipient's
use of the covered work in a country, would
infringe one or more identifiable patents in that
country that you have reason to believe are
valid.
If, pursuant to or in connection with a single
transaction or arrangement, you convey, or
propagate by procuring conveyance of, a
covered work, and grant a patent license to
some of the parties receiving the covered
work authorizing them to use, propagate,
modify or convey a specific copy of the
covered work, then the patent license you
grant is automatically extended to all
recipients of the covered work and works
based on it.
A patent license is “discriminatory” if it does
not include within the scope of its coverage,
prohibits the exercise of, or is conditioned
on the non-exercise of one or more of the
rights that are specifically granted under this
License. You may not convey a covered
work if you are a party to an arrangement
with a third party that is in the business of
distributing software, under which you make
payment to the third party based on the
extent of your activity of conveying the work,
and under which the third party grants, to any
of the parties who would receive the covered
work from you, a discriminatory patent license
(a) in connection with copies of the covered
work conveyed by you (or copies made
from those copies), or
(b) primarily for and in connection with specific
products or compilations that contain the
covered work, unless you entered into that
arrangement, or that patent license was
granted, prior to 28 March 2007.
Nothing in this License shall be construed
as excluding or limiting any implied license
or other defenses to infringement that may
otherwise be available to you under applicable
patent law.
12. No Surrender of Others' Freedom.
If conditions are imposed on you (whether
by court order, agreement or otherwise) that
contradict the conditions of this License, they
do not excuse you from the conditions of
this License. If you cannot convey a covered
work so as to satisfy simultaneously your
obligations under this License and any other
pertinent obligations, then as a consequence
you may not convey it at all. For example, if
you agree to terms that obligate you to collect
a royalty for further conveying from those
to whom you convey the Program, the only
way you could satisfy both those terms and
this License would be to refrain entirely from
conveying the Program.
13. Use with the GNU Affero General
Public License.
Notwithstanding any other provision of
this License, you have permission to link
or combine any covered work with a work
licensed under version 3 of the GNU Affero
General Public License into a single combined
work, and to convey the resulting work.
The terms of this License will continue to
apply to the part which is the covered work,
but the special requirements of the GNU
Affero General Public License, section 13,
concerning interaction through a network will
apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish
revised and/ or new versions of the GNU
General Public License from time to time.
Such new versions will be similar in spirit to
the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version
number. If the Program specifies that a certain
numbered version of the GNU General Public
License “or any later version” applies to it, you
have the option of following the terms and
conditions either of that numbered version
or of any later version published by the Free
Software Foundation. If the Program does
not specify a version number of the GNU
General Public License, you may choose any
version ever published by the Free Software
Foundation.
If the Program specifies that a proxy can
decide which future versions of the GNU
General Public License can be used, that
proxy's public statement of acceptance of a
version permanently authorizes you to choose
that version for the Program.
Later license versions may give you additional
or different permissions. However, no
additional obligations are imposed on any
author or copyright holder as a result of your
choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE
PROGRAM, TO THE EXTENT PERMITTED
BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM
“AS IS” WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK
AS TO THE QUALITY AND PERFORMANCE
OF THE PROGRAM IS WITH YOU. SHOULD
THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY
APPLICABLE LAW OR AGREED TO IN
WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MODIFIES
AND/OR CONVEYS THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO
YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT
OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES
SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE PROGRAM TO
OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of
liability provided above cannot be given local
legal effect according to their terms, reviewing
courts shall apply local law that most closely
approximates an absolute waiver of all civil
liability in connection with the Program,
unless a warranty or assumption of liability
accompanies a copy of the Program in return
for a fee.
END OF TERMS AND CONDITIONS
GNU LESSER GENERAL PUBLIC
LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software
Foundation, Inc. 51 Franklin Street, Fifth Floor,
Boston, MA 02110-1301
USA Everyone is permitted to copy and
distribute verbatim copies of this license
document, but changing it is not allowed.
[This is the first released version of the Lesser
GPL. It also counts as the successor of the
GNU Library Public License, version 2, hence
the version number 2.1.]
Preamble
The licenses for most software are designed
to take away your freedom to share and
change it. By contrast, the GNU General
Public Licenses are intended to guarantee
your freedom to share and change free
software to make sure the software is free
for all its users.
This license, the Lesser General Public
License, applies to some specially
designated software packages-typically
libraries-of the Free Software Foundation
and other authors who decide to use it.
You can use it too, but we suggest you first
think carefully about whether this license or
the ordinary General Public License is the
better strategy to use in any particular case,
based on the explanations below.
When we speak of free software, we are
referring to freedom of use, not price. Our
General Public Licenses are designed to
make sure that you have the freedom to
distribute copies of free software (and
charge for this service if you wish); that you
receive source code or can get it if you
want it; that you can change the software
and use pieces of it in new free programs;
and that you are informed that you can do
these things.
To protect your rights, we need to make
restrictions that forbid distributors to deny
you these rights or to ask you to surrender
these rights. These restrictions translate
to certain responsibilities for you if you
distribute copies of the library or if you
modify it.
For example, if you distribute copies of
the library, whether gratis or for a fee, you
must give the recipients all the rights that
we gave you. You must make sure that
they, too, receive or can get the source
code. If you link other code with the library,
you must provide complete object files to
the recipients, so that they can relink them
with the library after making changes to the
library and recompiling it. And you must
show them these terms so they know their
rights.
We protect your rights with a two-step
method: (1) we copyright the library, and (2)
we offer you this license, which gives you
legal permission to copy, distribute and/or
modify the library.
To protect each distributor, we want to
make it very clear that there is no warranty
for the free library. Also, if the library is
modified by someone else and passed
on, the recipients should know that what
they have is not the original version, so
that the original author’s reputation will
not be affected by problems that might be
introduced by others.
Finally, software patents pose a constant
threat to the existence of any free program.
We wish to make sure that a company
cannot effectively restrict the users of a
free program by obtaining a restrictive
license from a patent holder. Therefore, we
insist that any patent license obtained for
a version of the library must be consistent
with the full freedom of use specified in this
license.
Most GNU software, including some
libraries, is covered by the ordinary GNU
General Public License. This license, the
GNU Lesser General Public License,
applies to certain designated libraries, and
is quite different from the ordinary General
Public License. We use this license for
certain libraries in order to permit linking
those libraries into non-free programs.
When a program is linked with a library,
whether statically or using a shared library,
the combination of the two is legally
speaking a combined work, a derivative of
the original library. The ordinary General
Public License therefore permits such
linking only if the entire combination fits
its criteria of freedom. The Lesser General
Public License permits more lax criteria for
linking other code with the library.
We call this license the “Lesser” General
Public License because it does Less
to protect the user’s freedom than the
ordinary General Public License. It also
provides other free software developers
Less of an advantage over competing nonfree programs. These disadvantages are
the reason we use the ordinary General
Public License for many libraries. However,
the Lesser license provides advantages in
certain special circumstances.
For example, on rare occasions, there may
be a special need to encourage the widest
possible use of a certain library, so that it
becomes a de-facto standard. To achieve
this, non-free programs must be allowed to
use the library. A more frequent case is that
a free library does the same job as widely
used non-free libraries. In this case, there
is little to gain by limiting the free library to
free software only, so we use the Lesser
General Public License.
In other cases, permission to use a
particular library in non-free programs
enables a greater number of people to use
a large body of free software. For example,
permission to use the GNU C Library in
non-free programs enables many more
people to use the whole GNU operating
system, as well as its variant, the GNU/
Linux operating system.
Although the Lesser General Public License
is Less protective of the users’ freedom, it
does ensure that the user of a program that
is linked with the Library has the freedom
and the wherewithal to run that program
using a modified version of the Library.
The precise terms and conditions for
copying, distribution and modification
follow. Pay close attention to the difference
between a “work based on the library” and
a “work that uses the library”. The former
contains code derived from the library,
whereas the latter must be combined with
the library in order to run.
TERMS AND CONDITIONS FOR
COPYING, DISTRIBUTION AND
MODIFICATION
0. This License Agreement applies to any
software library or other program which
contains a notice placed by the copyright
holder or other authorized party saying
it may be distributed under the terms of
this Lesser General Public License (also
called “this License”). Each licensee is
addressed as “you”.
A “library” means a collection of software
functions and/ or data prepared so as to
be conveniently linked with application
programs (which use some of those
functions and data) to form executables.
The “Library”, below, refers to any such
software library or work which has been
distributed under these terms. A “work
based on the Library” means either the
Library or any derivative work under
copyright law: that is to say, a work
containing the Library or a portion of it,
either verbatim or with modifications and/or
translated straightforwardly into another
language. (Hereinafter, translation is
included without limitation in the term
“modification”.)
“Source code” for a work means the
preferred form of the work for making
modifications to it. For a library, complete
source code means all the source code for
all modules it contains, plus any associated
interface definition files, plus the scripts
used to control compilation and installation
of the library.
Activities other than copying, distribution
and modification are not covered by this
License; they are outside its scope. The act
of running a program using the Library is not
restricted, and output from such a program
is covered only if its contents constitute a
work based on the Library (independent of
the use of the Library in a tool for writing it).
Whether that is true depends on what the
Library does and what the program that
uses the Library does.
1. You may copy and distribute verbatim
copies of the Library’s complete source
code as you receive it, in any medium,
provided that you conspicuously and
appropriately publish on each copy
an appropriate copyright notice and
disclaimer of warranty; keep intact all
the notices that refer to this License and
to the absence of any warranty; and
distribute a copy of this License along
with the Library.
You may charge a fee for the physical act
of transferring a copy, and you may at
your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies
of the Library or any portion of it, thus
forming a work based on the Library, and
copy and distribute such modifications
or work under the terms of Section 1
above, provided that you also meet all of
these conditions:
a) The modified work must itself be a
software library. b) You must cause the files
modified to carry prominent notices stating
that you changed the files and the date of
any change. c) You must cause the whole
of the work to be licensed at no charge
to all third parties under the terms of this
License. d) If a facility in the modified Library
refers to a function or a table of data to be
supplied by an application program that
uses the facility, other than as an argument
passed when the facility is invoked, then
you must make a good faith effort to ensure
that, in the event an application does not
supply such function or table, the facility
still operates, and performs whatever part
of its purpose remains meaningful. (For
example, a function in a library to compute
square roots has a purpose that is entirely
well-defined independent of the application.
Therefore, Subsection 2d requires that any
application-supplied function or table used
by this function must be optional: if the
application does not supply it, the square
root function must still compute square
roots.) These requirements apply to the
modified work as a whole. If identifiable
sections of that work are not derived
from the Library, and can be reasonably
considered independent and separate
works in themselves, then this License, and
its terms, do not apply to those sections
when you distribute them as separate
works. But when you distribute the same
sections as part of a whole which is a work
based on the Library, the distribution of the
whole must be on the terms of this License,
whose permissions for other licensees
extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section
to claim rights or contest your rights to
work written entirely by you; rather, the
intent is to exercise the right to control the
distribution of derivative or collective works
based on the Library.
In addition, mere aggregation of another
work not based on the Library with the
Library (or with a work based on the Library)
on a volume of a storage or distribution
medium does not bring the other work
under the scope of this License.
3. You may opt to apply the terms of the
ordinary GNU General Public License
instead of this License to a given
copy of the Library. To do this, you
must alter all the notices that refer to
this License, so that they refer to the
ordinary GNU General Public License,
version 2, instead of to this License. (If
a newer version than version 2 of the
ordinary GNU General Public License
has appeared, then you can specify that
version instead if you wish.) Do not make
any other change in these notices.
Once this change is made in a given copy,
it is irreversible for that copy, so the ordinary
GNU General Public License applies to all
subsequent copies and derivative works
made from that copy.
This option is useful when you wish to
copy part of the code of the Library into a
program that is not a library.
4. You may copy and distribute the Library
(or a portion or derivative of it, under
Section 2) in object code or executable
form under the terms of Sections 1 and
2 above provided t hat you accompany
it with the complete corresponding
machine-readable source code,
which must be distributed under the
terms of Sections 1 and 2 above on a
medium customarily used for software
interchange.
If distribution of object code is made by
offering access to copy from a designated
place, then offering equivalent access to
copy the source code from the same place
satisfies the requirement to distribute the
source code, even though third parties are
not compelled to copy the source along
with the object code.
5. A program that contains no derivative
of any portion of the Library, but is
designed to work with the Library by
being compiled or linked with it, is called
a “work that uses the Library”. Such a
work, in isolation, is not a derivative work
of the Library, and therefore falls outside
the scope of this License.
However, linking a “work that uses the
Library” with the Library creates an
executable that is a derivative of the Library
(because it contains portions of the Library),
rather than a “work that uses the library”.
The executable is therefore covered by
this License. Section 6 states terms for
distribution of such executables.
When a “work that uses the Library” uses
material from a header file that is part of the
Library, the object code for the work may
be a derivative work of the Library even
though the source code is not. Whether this
is true is especially significant if the work
can be linked without the Library, or if the
work is itself a library. The threshold for this
to be true is not precisely defined by law.
If such an object file uses only numerical
parameters, data structure layouts
and accessors, and small macros and
small inline functions (ten lines or less in
length), then the use of the object file is
unrestricted, regardless of whether it is
legally a derivative work. (Executables
containing this object code plus portions of
the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the
Library, you may distribute the object code
for the work under the terms of Section 6.
Any executables containing that work also
fall under Section 6, whether or not they are
linked directly with the Library itself.
6. As an exception to the Sections above,
you may also combine or link a “work
that uses the Library” with the Library
to produce a work containing portions
of the Library, and distribute that work
under terms of your choice, provided
that the terms permit modification of the
work for the customer’s own use and
reverse engineering for debugging such
modifications.
You must give prominent notice with each
copy of the work that the Library is used
in it and that the Library and its use are
covered by this License. You must supply
a copy of this License. If the work during
execution displays copyright notices, you
must include the copyright notice for the
Library among them, as well as a reference
directing the user to the copy of this
License. Also, you must do one of these
things:
a) Accompany the work with the complete
corresponding machine-readable source
code for the Library including whatever
changes were used in the work (which
must be distributed under Sections
1 and 2 above); and, if the work is
an executable linked with the Library,
with the complete machine readable “
work that uses the Library”, as object
code and/or source code, so that the
user can modify the Library and then
relink to produce a modified executable
containing the modified Library. (It is
understood that the user who changes
the contents of definitions files in the
Library will not necessarily be able to
recompile the application to use the
modified definitions.)
b) Use a suitable shared library mechanism
for linking with the Library. A suitable
mechanism is one that
(1) uses at run time a copy of the library
already present on the user’s computer
system, rather than copying library
functions into the executable, and (2) will
operate properly with a modified version
of the library, if the user installs one, as
long as the modified version is interfacecompatible with the version that the work
was made with.
c) Accompany the work with a written offer,
valid for at least three years, to give the
same user the materials specified in
Subsection 6a, above, for a charge no
more than the cost of performing this
distribution.
d) If distribution of the work is made
by offering access to copy from a
designated place, offer equivalent access
to copy the above specified materials
from the same place.
e) Verify that the user has already received
a copy of these materials or that you
have already sent this user a copy.
For an executable, the required form of the
“work that uses the Library” must include
any data and utility programs needed
for reproducing the executable from it.
However, as a special exception, the
materials to be distributed need not include
anything that is normally distributed (in
either source or binary form) with the major
components (compiler, kernel, and so
on) of the operating system on which the
executable runs, unless that component
itself accompanies the executable.
It may happen that this requirement
contradicts the license restrictions of other
proprietary libraries that do not normally
accompany the operating system. Such
a contradiction means you cannot use
both them and the Library together in an
executable that you distribute.
7. You may place library facilities that are
a work based on the Library side-byside in a single library together with
other library facilities not covered by this
License, and distribute such a combined
library, provided that the separate
distribution of the work based on the
Library and of the other library facilities is
otherwise permitted, and provided that
you do these two things:
a) Accompany the combined library with
a copy of the same work based on the
Library, uncombined with any other
library facilities. This must be distributed
under the terms of the Sections above.
b) Give prominent notice with the combined
library of the fact that part of it is a work
based on the Library, and explaining
where to find the accompanying
uncombined form of the same work.
8. You may not copy, modify, sublicense,
link with, or distribute the Library except
as expressly provided under this License.
Any attempt otherwise to copy, modify,
sublicense, link with, or distribute the
Library is void, and will automatically
terminate your rights under this License.
However, parties who have received
copies, or rights, from you under this
License will not have their licenses
terminated so long as such parties
remain in full compliance.
9. You are not required to accept this
License, since you have not signed
it. However, nothing else grants you
permission to modify or distribute the
Library or its derivative works. These
actions are prohibited by law if you do
not accept this License. Therefore, by
modifying or distributing the Library (or
any work based on the Library), you
indicate your acceptance of this License
to do so, and all its terms and conditions
for copying, distributing or modifying the
Library or works based on it.
10. Each time you redistribute the Library
(or any work based on the Library),
the recipient automatically receives
a license from the original licensor to
copy, distribute, link with or modify
the Library subject to these terms and
conditions. You may not impose any
further restrictions on the recipients’
exercise of the rights granted herein.
You are not responsible for enforcing
compliance by third parties with this
License.
11. If, as a consequence of a court
judgment or allegation of patent
infringement or for any other reason
(not limited to patent issues), conditions
are imposed on you (whether by
court order, agreement or otherwise)
that contradict the conditions of this
License, they do not excuse you
from the conditions of this License. If
you cannot distribute so as to satisfy
simultaneously your obligations under
this License and any other pertinent
obligations, then as a consequence you
may not distribute the Library at all. For
example, if a patent license would not
permit royalty free redistribution of the
Library by all those who receive copies
directly or indirectly through you, then
the only way you could satisfy both it
and this License would be to refrain
entirely from distribution of the Library.
If any portion of this section is held invalid
or unenforceable under any particular
circumstance, the balance of the section
is intended to apply, and the section
as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to
induce you to infringe any patents or other
property right claims or to contest validity
of any such claims; this section has the
sole purpose of protecting the integrity of
the free software distribution system which
is implemented by public license practices.
Many people have made generous
contributions to the wide range of software
distributed through that system in reliance
on consistent application of that system; it
is up to the author/donor to decide if he or
she is willing to distribute software through
any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly
clear what is believed to be a consequence
of the rest of this License.
12. If the distribution and/or use of the
Library is restricted in certain countries
either by patents or by copyrighted
interfaces, the original copyright
holder who places the Library under
this License may add an explicit
geographical distribution limitation
excluding those countries, so that
distribution is permitted only in or
among countries not thus excluded. In
such case, this License incorporates
the limitation as if written in the body of
this License.
13. The Free Software Foundation may
publish revised and/or new versions of the
Lesser General Public License from time
to time. Such new versions will be similar
in spirit to the present version, but may
differ in detail to address new problems or
concerns.
Each version is given a distinguishing
version number. If the Library specifies
a version number of this License which
applies to it and “any later version”, you
have the option of following the terms and
conditions either of that version or of any
later version published by the Free Software
Foundation. If the Library does not specify
a license version number, you may choose
any version ever published by the Free
Software Foundation.
14. If you wish to incorporate parts of the
Library into other free programs whose
distribution conditions are incompatible
with these, write to the author to ask
for permission. For software which
is copyrighted by the Free Software
Foundation, write to the Free Software
Foundation; we sometimes make
exceptions for this. Our decision will be
guided by the two goals of preserving
the free status of all derivatives of our
free software and of promoting the
sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED
FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE LIBRARY,
TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/
OR OTHER PARTIES PROVIDE
THE LIBRARY “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE
OF THE LIBRARY IS WITH YOU.
SHOULD THE LIBRARY PROVE
DEFECTIVE, YOU ASSUME THE COST
OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY
APPLICABLE LAW OR AGREED TO
IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY
WHO MAY MODIFY AND/OR
REDISTRIBUTE THE LIBRARY AS
PERMITTED ABOVE, BE LIABLE TO
YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF
THE LIBRARY TO OPERATE WITH ANY
OTHER SOFTWARE), EVEN IF SUCH
HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your
New Libraries
If you develop a new library, and you want
it to be of the greatest possible use to
the public, we recommend making it free
software that everyone can redistribute
and change. You can do so by permitting
redistribution under these terms (or,
alternatively, under the terms of the ordinary
General Public License).
To apply these terms, attach the following
notices to the library. It is safest to attach
them to the start of each source file to
most effectively convey the exclusion of
warranty; and each file should have at least
the “copyright” line and a pointer to where
the full notice is found. one line to give the
library’s name and an idea of what it does.
Copyright (C) year name of author
This library is free software; you can
redistribute it and/ or modify it under
the terms of the GNU Lesser General
Public License as published by the Free
Software Foundation; either version 2.1 of
the License, or (at your option) any later
version.
This library is distributed in the hope
that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied
warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.
See the GNU Lesser General Public
License for more details.
You should have received a copy of the
GNU Lesser General Public License along
with this library; if not, write to the Free
Software Foundation, Inc., 51 Franklin
Street, Fifth Floor, Boston, MA 021101301 USA Also add information on how to
contact you by electronic and paper mail.
You should also get your employer (if you
work as a programmer) or your school, if
any, to sign a “copyright disclaimer” for the
library, if necessary. Here is a sample; alter
the names:
Yoyodyne, Inc., hereby disclaims all
copyright interest in the library ‘Frob’ (a
library for tweaking knobs) written by James
Random Hacker.
signature of Ty Coon, 1 April 1990 Ty Coon,
President of Vice.
OpenSSL LICENSE
Copyright (c) 1998-2006 The OpenSSL
Project. All rights reserved. Redistribution
and use in source and binary forms, with
or without modification, are permitted
provided that the following conditions are
met:
1. Redistributions of source code must
retain the above copyright notice, this list
of conditions and the following disclaimer.
2. Redistributions in binary form must
reproduce the above copyright notice,
this list of conditions and the following
disclaimer in the documentation and/
or other materials provided with the
distribution.
3. All advertising materials mentioning
features or use of this software must
display the following acknowledgment:
“This product includes software
developed by the OpenSSL Project for
use in the OpenSSL Toolkit. (http://www.
openssl.org/)”
4. The names “OpenSSL Toolkit” and
“OpenSSL Project” must not be used to
endorse or promote products derived
from this software without prior written
permission. For written permission, please
contact openssl-core@openssl.org.
5. Products derived from this software may
not be called “OpenSSL” nor may
“OpenSSL” appear in their names without
prior written permission of the OpenSSL
Project.
6. Redistributions of any form
whatsoever must retain the following
acknowledgment: “This product includes
software developed by the OpenSSL
Project for use in the OpenSSL Toolkit
(http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE
OpenSSL PROJECT “AS IS” AND ANY
EXPRESSED OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE OpenSSL
PROJECT OR ITS CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT
OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE. This
product includes cryptographic software
written by Eric Young (eay@cryptsoft.com).
This product includes software written by
Tim Hudson(tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young
(eay@cryptsoft. com) All rights reserved.
This package is an SSL implementation
written by Eric Young (eay@cryptsoft. com).
The implementation was written so as to
conform with Netscapes SSL. This library
is free for commercial and non-commercial
use as long as the following conditions are
aheared to. The following conditions apply
to all code found in this distribution, be it
the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation
included with this distribution is covered by
the same copyright terms except that the
holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young’s, and as
such any Copyright notices in the code are
not to be removed. If this package is used
in a product, Eric Young should be given
attribution as the author of the parts of the
library used. This can be in the form of a
textual message at program startup or in
documentation (online or textual) provided
with the package. Redistribution and use
in source and binary forms, with or without
modification, are permitted provided that
the following conditions are met:
1. Redistributions of source code must
retain the copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must
reproduce the above copyright notice,
this list of conditions and the following
disclaimer in the documentation and/
or other materials provided with the
distribution.
3. All advertising materials mentioning
features or use of this software must
display the following acknowledgement:
“This product includes cryptographic
software written by Eric Young (eay@
cryptsoft.com)” The word ‘cryptographic’
can be left out if the rouines from the
library being used are not cryptographic
related :-).
4. If you include any Windows specific
code (or a derivative thereof) from the
apps directory (application code) you
must include an acknowledgement: “This
product includes software written by Tim
Hudson (tjh@ cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC
YOUNG ‘‘AS IS AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE AUTHOR OR
CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any
publically available version or derivative of
this code cannot be changed. i.e. this code
cannot simply be copied and put under
another distribution licence [including the
GNU Public Licence].
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
www.samsungipolis.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325