White Rodgers 1F97W-71 Programming instructions

OPERATION GUIDE
1F97W-71
7-Day Programmable Electronic
Digital Thermostat
WHITE-RODGERS
WHIT
E-RO
DGER
S
Operator: Save this booklet for future use!
About Your New Thermostat . . .
Your new White-Rodgers Digital Thermostat uses the technology of a solid-state microcomputer to
provide precise time/temperature control. This thermostat offers you the flexibility to design heating and
cooling programs that fit your needs.
Please read this manual thoroughly before operating or programming your thermostat. If you have
questions, write to us at the address shown on the back cover of this manual.
2
In This Guide . . .
YOUR NEW THERMOSTAT'S
FEATURES ................................................ 4
OPERATING YOUR THERMOSTAT ............. 5
PARTS OF THE THERMOSTAT
The Back Of the Thermostat Body
The Display
The Thermostat Buttons
OPERATING FEATURES
PROGRAMMING YOUR
THERMOSTAT ........................................ 18
PLANNING FOR YOUR NEEDS
ENTERING YOUR PROGRAM
Set Current Time and Day
Select Heating and Cooling Temperatures
Program Heating/Cooling Times and
Heating Temperatures
Program Cooling Temperatures
Using the HOLD/COPY Button
CHECK YOUR PROGRAMMING
QUESTIONS AND ANSWERS ..................... 33
Operator: Save this
booklet for future use!
3
YOUR NEW THERMOSTAT’S FEATURES
• Seven independent day programming
• Simultaneous heat and cool program storage
• Four separate time/temperature settings per
24-hour period
• Computed Energy Management Recovery
(EMR)
• Automatic changeover (operator-selectable)
• Armchair programming capability
• Backlit LCD displays continuous set point,
time, and room temperature
• 1.5 volt "AA" Energizer® alkaline battery backup
• Preprogrammed temperature control
4
•
•
•
•
•
•
•
•
•
•
•
Adjustable cycle times
Compressor short cycle protection
Programmable blower control
Blower delay in the cooling cycle
Audio and visual prompting during operation
Two hour temperature override
Manual program override (HOLD temperature)
°F/°C convertibility
Keypad lockout (operator-selectable)
Temperature range 40° to 99°F
Compatible with Remote Sensor (installerselectable)
OPERATING YOUR THERMOSTAT
Before you begin programming your thermostat,
you should be familiar with its features and with the
display and the location and operation of the thermostat buttons. The information in this section will
help you become familiar with your new thermostat
so that you can easily program it.
Your thermostat consists of two parts: the thermostat body and the subbase.
The subbase is attached to the wall, but you can
remove the thermostat body for easy programming. To remove the thermostat body from the
subbase, grasp the thermostat body and gently
pull it straight out from the subbase. To attach the
thermostat body, line up the six terminal pins on the
upper section of the thermostat back with the
matching connector on the subbase. Insert these,
then gently pivot the thermostat body down to
! CAUTION
Remove power from the system at the
circuit breaker/fuse box before removing
or attaching the thermostat body. Equipment damage and/or personal injury could
occur.
SUBBASE
THERMOSTAT
BODY
5
connect the three pin connectors on the lower
portion of the thermostat back. Gently push until
the snap connectors engage. DO NOT FORCE
OR PRY THE THERMOSTAT, as this may damage the unit.
PARTS OF THE THERMOSTAT
The Back of The Thermostat Body
Turn the thermostat body over. On the back are
the 3 "AA" Energizer® alkaline batteries and the
two option switch groups (A and B).
1.
6
The "AA" Energizer® alkaline batteries provide
power to the thermostat when the 24vAC
power is interrupted (for example, when you
remove the thermostat from the wall for programming). Fresh batteries will maintain the
stored program for approximately a year. If
power loss is long enough for the program to
be lost, the thermostat will automatically return to the factory programmed temperatures
(64°F heating and 82°F cooling) when power
is restored. You must reprogram the thermostat if this happens.
If the word BATTERY is flashing in the display
window, the batteries are low and should be
replaced with fresh "AA" Energizer® alkaline
batteries.
! CAUTION
Before removing thermostat from the wall
to replace the batteries, remove 24vAC
power from the thermostat at the breaker/
fuse box.
2.
You may adjust the option switches for EMR,
keypad lockout, and automatic changeover from
heat to cool (see OPERATING FEATURES).
6-pin Connector
On the following pages there are brief descriptions
of the display and the thermostat buttons.
W14 W22
Other than
and
, the buttons are located behind the thermostat door. To open the
door, pull the door out from the top, then swing the
door down on its hinges.
Batteries
(Group A)
(Group B)
Option Switches
3-pin Connector
BACK OF THERMOSTAT BODY
7
The Display
1 Continuously displays system mode (HEAT,
OFF, COOL, AUTO, HOLD). During programming, the day of the week is displayed
(MON, TUE, WED, etc.).
2 Alternately displays room temperature (F denotes degrees Fahrenheit and C denotes degrees Celsius) and time of day (A denotes AM
time and P denotes PM time).
3 Displays the setpoint temperature.
4 In VIEW TEMP mode, A, B, C, and D are the
1st, 2nd, 3rd, and 4th heating or cooling temperatures available for programming.
8
5 The word BATTERY flashes on the display
when the "AA" alkaline batteries are weak and
should be replaced. The word BATTERY is
displayed continuously (non-flashing) when
thermostat is running on battery power only.
6 FAN ON is displayed when the blower is
operating continuously. FAN AUTO is displayed during automatic fan operation (when
the blower cycles with the heating or cooling
system).
FAN AUTO
SYSTEM
HEAT-OFF-COOL-AUTO
FAN
ON
1
A
4
- AUTO
2
FAN AUTO
6
TIME
FWD
SET
CLOCK
VIEW
PRGM
HOLD
COPY
TIME
BACK
ADV
DAY
VIEW
TEMP
RUN
PRGM
3
3
B
4
FAN ON
6
BATTERY
2
5
9
The Thermostat Buttons
12 Used to initiate or review thermostat programming.
7 Sets the system mode (HEATing, OFF,
COOLing, or AUTOmatic changeover).
8 Selects fan operation (see #6, above). This
button is also used to program the fan to run
continuously during a program period.
9 Runs display forward or backward through
time, day, or anticipation settings during programming.
10 Used with the
TIME
FWD
and
TIME
BACK
buttons to set
current time and day of the week.
11 Used during programming to set the day of the
week to be programmed. Also used in conjunction with the
SET
CLOCK
pation setting mode.
button to enter antici-
13 Used to select heating and cooling temperatures to be programmed.
14 Used to manually override programming to
hold at a selected temperature (when HOLD is
displayed). Also used to copy one day's
programming into another (when COPY is
displayed).
15 Used to start program operation after programming. Also used to return thermostat to
program operation after being in HOLD mode.
16 (Red arrow) Raises temperature setting (99°F
or 37°C maximum).
17 (Blue arrow) Lowers temperature setting (40°F
or 4°C minimum).
18 The red indicator light glows whenever heating, cooling, or fan are in operation.
10
17 16
18
FAN AUTO
7
8
SYSTEM
HEAT-OFF-COOL-AUTO
FAN
ON
- AUTO
9
TIME
FWD
SET
CLOCK
VIEW
PRGM
HOLD
COPY
TIME
BACK
ADV
DAY
VIEW
TEMP
RUN
PRGM
10 11 12 13 14 15
11
OPERATING FEATURES
Now that you are familiar with the thermostat
display and buttons, read the following information
to learn about the many features of the thermostat.
• COMPUTED ENERGY MANAGEMENT RECOVERY (EMR) — The thermostat’s microcomputer can be set to automatically calculate
the time it will take to change the temperature
to the next program setting. Then the thermostat will activate the heating or cooling system
to change the temperature so that the desired
temperature is reached at the beginning of the
next program period. As an example of this
feature, assume that you have programmed
your thermostat to provide an overnight heating temperature of 62°F, and that during the
next program period, beginning at 6:00 AM,
you have programmed a temperature of 70°F.
12
The thermostat will automatically activate the
heating system at 5:00 AM, so that the programmed 70°F temperature is reached by
about 6:00 AM.
This feature is controlled by Group B option
switch #3. To enable the EMR function, first
you must move option switch #3 (located on
the back of the thermostat body) to the OFF
position, if it has not already been done. To do
this, turn off 24v AC power to the thermostat.
Then remove the thermostat body from the
wall. Check the position of switch #3 (the last
switch on the right). If it is OFF (down), simply
put the thermostat back on the wall and restore 24v AC power. If the switch is ON (up),
remove the battery, then use a pencil or small
screwdriver to move the switch to the OFF
position (see figure below). Leave the battery
out of the thermostat for at least two minutes,
to allow the thermostat to reset itself. See
AUTOMATIC CHANGEOVER to determine
proper positions of Group B option switches
#1 and #2.
EMR Switch Positions
ON
1
Group B
Option
Switches
2
3
Switch #1 (see AUTOMATIC CHANGEOVER)
Switch #2 (see AUTOMATIC CHANGEOVER)
Switch #3 OFF
• AUTOMATIC CHANGEOVER — If you have
a heating/cooling system, you can set the
thermostat to automatically switch the system
from heating to cooling as needed. (If you
have a heating only system, Group B option
switch #1 should be OFF and option switch #2
should be ON.) To enable automatic
changeover, you must move Group B option
switch #1 to the ON position and switch #2 to
the OFF position. Turn off 24v AC power to the
thermostat. Then remove the thermostat body
from the wall. Check the position of Group B
option switches #1 and #2 (the first two switches
on the left). If they are in the correct positions,
simply put the thermostat back on the wall and
restore 24v AC power. If the switches are not
correctly positioned, remove the battery, then
use a pencil or small screwdriver to move the
switches to the correct positions (see figure on
next page). Leave the battery out of the
thermostat for at least two minutes, to allow
the thermostat to reset itself. Replace the
battery, reprogram the thermostat, if necessary, put the thermostat back on the wall, and
restore 24v AC power. To set the thermostat
for automatic changeover after programming,
press
SYSTEM
HEAT-OFF-COOL-AUTO
to set the thermostat to AUTO
13
(the setpoint temperature display is blank in
the AUTO mode). The system will now automatically switch between heating and cooling,
depending on the actual room temperature.
Auto Changeover Switch Positions
ON
1
Group B
Option
Switches
2
3
Switch #1 ON
Switch #2 OFF
Switch #3 (see Energy Management Recovery)
NOTE
In the AUTO mode, the thermostat will not allow
the temperature separation between the highest
heat setting and the lowest cool setting to be less
than 1°F. For example, if the highest heat setting
is 75°F, the lowest cool setting cannot be below
77°F (see diagram at right).
14
79
78
77
76
75
74
73
COOLING TEMPERATURES
DEAD BAND 1°F
HEATING TEMPERATURES
• TWO HOUR TEMPERATURE OVERRIDE —
or
until the display shows
Press
the temperature you want. The thermostat will
override current programming and keep the
room temperature at the selected temperature
for two hours. After two hours, the thermostat
will automatically revert to the program.
• HOLD TEMPERATURE — The thermostat
can hold any temperature within its range for
an indefinite period, without reverting to the
program. Press
HOLD
COPY
. HOLD will be dis-
played. Then choose the desired hold temperature by pressing
or
. The
thermostat will hold the room temperature at
the selected setting until you press
RUN
PRGM
start program operation again. This feature is
ideal for energy conservation when the building is unoccupied for an extended period of
time.
• °F/°C CONVERTIBILITY — Press
TIME
BACK
TIME
FWD
! CAUTION
to
and
at the same time until the temperature
display is in °C (Celsius). To display °F, repeat
the process.
• ADJUSTABLE HEATING AND COOLING
CYCLE TIMES (ANTICIPATION) — If the
heating/cooling system is turning on and off
too often (short cycles) or not often enough
(long cycles), you may want to adjust the
anticipation setting.
A cooling anticipation setting of less than
10 may cause decreased compressor life.
To adjust heat anticipation, press
ADV
DAY
SET
CLOCK
and
at the same time. The display will show
HEAT 5 (this is the factory preprogrammed
heating anticipation setting). You may select
any anticipation setting from 4 to 40 (note
that for hydronic systems, a minimum anticipation setting of 15 is recommended).
Whenever adjusting anticipation, increase or
decrease the displayed number by only one
or two digits, then let the system run for a while
to see if the adjustment is sufficient. If the heat
cycles are too short, press
TIME
FWD
to increase
the cycle time. If the heat cycles are too long,
15
press
TIME
BACK
to decrease the cycle time. To set
cooling anticipation, press
SET
CLOCK
and
ADV
DAY
at the same time again. The display will show
COOL 14 (factory preprogrammed cooling
anticipation). Use the
TIME
FWD
and
tons to adjust anticipation. Press
TIME
BACK
RUN
PRGM
butto
return to your program.
• LOW BATTERY INDICATOR — The three
"AA" alkaline batteries will maintain thermostat programming for approximately one year
if power to the thermostat fails. The word
BATTERY will flash on the display if the "AA"
alkaline batteries are low and should be replaced. The thermostat will also make a
beeping sound every five minutes when batteries need replacing. To override the beeping, press any button on the keypad. The
16
beeping will stop for 15 hours, then start again.
You may again stop the beeping by pressing
any button on the keypad. After turning the
beep off three times, the thermostat will quit
beeping. However, you should always change
the batteries as soon as possible to ensure
that programming will not be lost in the event
of a power outage. You should also change
the batteries at least once a year.
! CAUTION
Fresh batteries must always be installed
for millivolt systems. The heating system
will not operate if batteries are not installed
or if battery power is low.
The word BATTERY will be displayed continuously (non-flashing) when 24v AC power is not
being supplied to the thermostat and the thermostat is operating on battery power only.
NOTE
On systems with Taco zone valves, the indicator
light will flash during the heating cycle.
• COMPRESSOR SHORT CYCLE PROTECTION — To protect your compressor from
potential damage due to rapid cycling, this
thermostat has a built-in delay of 5 minutes
between cooling cycles. The following may
cause a time delay in COOL:
a) Return of power after a power outage.
b) Pressing
SYSTEM
HEAT-OFF-COOL-AUTO
to change operating
modes.
c) Pressing
, creating a call for COOL
too soon after a previous call.
• TOTAL KEYPAD LOCKOUT — When Group
A option switch #1 is in the total keypad
lockout position (ON), programs cannot be
altered and all buttons are disabled.
NOTE
Programming should be completed and batteries
should be installed before changing Group A
option switches #1 or #2.
17
PROGRAMMING
• AUDIO PROMPTING — Each time you press
a button, the thermostat will beep.
• BACKLIT DISPLAY — When you press any
button on the thermostat, the display is lit for
approximately eight seconds.
• SYSTEM INDICATOR LIGHT — The red light
on the upper right part of the thermostat indicates system operation (see PARTS OF THE
THERMOSTAT).
Total Keypad Lockout Switch Positions
ON
1
Group A
Option
Switches
To enable total keypad lockout, move Group
A option switch #1 to ON (see figure above).
To disable total keypad lockout, move option
switch #1 to OFF.
2
PROGRAMMING
Switch #1 ON
Switch #2 OFF
PROGRAMMING YOUR THERMOSTAT
Now you are ready to program your thermostat.
This section will help you plan your thermostat's
program to meet your needs.
For maximum comfort and efficiency, keep the
following guidelines in mind when planning your
program.
18
• When heating (cooling) your building, program the temperatures to be cooler (warmer)
when the building is vacant or during periods
of low activity.
• During early morning hours, the need for cooling is usually minimal.
PLANNING FOR YOUR NEEDS
First, answer the following questions to help you
decide what your needs are. If you are using the
thermostat for a commercial application (a store,
office building, etc.), answer questions 1 through 4.
If you are using the thermostat in your home,
answer questions 5 through 8.
FOR COMMERCIAL APPLICATIONS:
1a. What time does the first person arrive at the
building in the morning?
b. What temperature should the building be at
this time? (heating? cooling?) These will be
your MOR (morning) temperature settings.
2a. What time do the building occupants reach a
maximum activity level (using lights, equipment, meeting rooms, etc.)?
b. What temperature should the building be at
this time? These will be your DAY temperature settings.
3a. What time do the building occupants reach a
minimum activity level (limited personnel in
building)?
b. What temperature should the building be at
this time? These will be your EVE (evening)
temperature settings.
4a. What time does the building become vacant?
b. What temperature should the building be at
this time? These will be your NHT (night)
temperature settings.
IN YOUR HOME:
5a. What time does the first person get up in the
morning?
b. What temperature should the house be at this
time? These will be your MOR (morning)
temperature settings.
19
6a. What time does the last person leave the
house in the morning?
b. What temperature should the house be at this
time? These will be your DAY temperature
settings.
7a. What time does the first person arrive home in
the evening?
b. What temperature should the house be at this
time? These will be your EVE (evening)
temperature settings.
8a. What time does the last person go to bed at night?
b. What temperature should the house be at this
time? These will be your NHT (night) temperature settings.
Now look at the factory preprogrammed times and
temperatures shown at right. If this program will
suit your needs, simply press
RUN
PRGM
running the factory preset program.
20
to begin
Cooling Program for
ALL Days of the Week:
Heating Program for
ALL days of the Week:
PERIOD
1
2
3
4
TIME
5:00 AM
9:00 AM
4:00 PM
10:00 PM
TEMP
70
70
70
64
PERIOD
1
2
3
4
TIME
5:00 AM
9:00 AM
4:00 PM
10:00 PM
TEMP
78
82
78
78
If you want to change the preprogrammed times
and temperatures, follow these steps.
1.
Determine the heating and cooling temperatures
you want to use. You may select up to four heating
temperatures (HEAT A, HEAT B, HEAT C, and
HEAT D), and up to four cooling temperatures
(COOL A, COOL B, COOL C, and COOL D). Use
the table on the following page to write down the
temperatures you have selected.
NOTE
To operate properly in the AUTO mode, there must
be a minimum 1°F separation between the high-
est heat temperature and the lowest cool temperature (see diagram below).
79
78
77
76
75
74
73
2.
COOLING TEMPERATURES
DEAD BAND 1°F
HEATING TEMPERATURES
Determine the time periods during which you
will program the temperatures you have just
selected. You must program four periods for
each day (periods 1, 2, 3, and 4). However,
you may use the same heating and cooling
temperatures for consecutive time periods.
Also keep in mind that, for any given day, you
can only program one set of times for both
heating and cooling (for example, if you select
5:00 AM to begin heating period 1 on Monday,
then your cooling period 1 for Monday will also
begin at 5:00 AM). However, you may choose
Temperature
Designation
Your
Selected
Temperatures*
Factory
Preprogrammed
Temperature
HEAT A
HEAT B
HEAT C
HEAT D
70
70
70
64
COOL A
COOL B
COOL C
COOL D
78
82
78
78
* You may only program heating temperatures you have selected
into the heating program and cooling temperatures into the
cooling program (for example, you cannot program the COOL A
temperature into your heating program). You may program the
temperatures you choose in any order, and you may use the
same temperature in consecutive program periods (for example,
you may program period 1 with temperature B and periods 2, 3,
and 4 with temperature A). You do not have to use all possible
temperature choices (for example, you may want to select
temperatures for HEAT A and HEAT B only – in this case, the
HEAT C and HEAT D temperatures would stay the same as
previously programmed).
21
different time periods for each day separately
(for example, heating/cooling period 1 on Monday may begin at 5:00 AM, but heating/cooling
period 1 on Saturday may begin at 9:00 AM).
Use the following table to plan your program
time periods, and the temperatures you want
during each period. You may also want to look
at the sample program table to get an idea of
how the thermostat can be programmed.
alkaline batteries must be installed to perform offwall programming. BE SURE SYSTEM SWITCH IS
SET TO OFF POSITION BEFORE REATTACHING THERMOSTAT TO SUBBASE!
NOTE
You cannot program the thermostat with the SYSTEM SWITCH in the AUTO position.
Set Current Time and Day
ENTERING YOUR PROGRAM
Follow these steps to enter the heating/cooling
program you have selected.
1.
22
SET
CLOCK
once. The display will show
minutes only.
NOTE
We recommend that you remove the thermostat
from the wall for programming (especially for entering cooling programming). Fresh "AA" Energizer®
Press
EXAMPLE:
2.
Press and hold either
TIME
FWD
reach the correct minutes.
or
TIME
BACK
until you
Heating/Cooling Schedule Plan
THIS THERMOSTAT ALLOWS ONE SET OF TIMES FOR BOTH HEATING AND COOLING
Period 1
Period 2
Period 3
Period 4
Heat Cool
Heat Cool
Heat Cool
Heat Cool
Time Temp. Temp. Time Temp. Temp. Time Temp. Temp. Time Temp. Temp.
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
23
Joe's Restaurant
Closed Mondays
Open Tues. – Sat. 10:30 AM to 10:00 PM
Open Sunday 6:30 AM to 2:00 PM
SAMPLE
Heating/Cooling Schedule Plan
HEAT A = 65°
HEAT B = 68°
HEAT C = 70°
HEAT D = 72°
COOL A = 80°
COOL B = 78°
COOL C = 76°
COOL D = 74°
THIS THERMOSTAT ALLOWS ONE SET OF TIMES FOR BOTH HEATING AND COOLING
Period 1
Period 2
Period 3
Period 4
Heat Cool
Heat Cool
Heat Cool
Heat Cool
Time Temp. Temp. Time Temp. Temp. Time Temp. Temp. Time Temp. Temp.
24
Monday
5:00 AM
65° (A)
80° (A) 9:00 AM
65° (A)
80° (A) 3:30 PM
65° (A)
80° (A) 11:30 PM
65° (A)
80° (A)
Tuesday
5:00 AM
65° (A)
80° (A) 9:00 AM
70° (C)
76° (C) 3:30 PM
72° (D)
74° (D) 11:30 PM
65° (A)
80° (A)
Wednesday
5:00 AM
65° (A)
80° (A) 9:00 AM
70° (C)
76° (C) 3:30 PM
72° (D)
74° (D) 11:30 PM
65° (A)
80° (A)
Thursday
5:00 AM
65° (A)
80° (A) 9:00 AM
70° (C)
76° (C) 3:30 PM
72° (D)
74° (D) 11:30 PM
65° (A)
80° (A)
Friday
5:00 AM
65° (A)
80° (A) 9:00 AM
70° (C)
76° (C) 3:30 PM
72° (D)
74° (D) 11:30 PM
65° (A)
80° (A)
Saturday
5:00 AM
65° (A)
80° (A) 9:00 AM
70° (C)
76° (C) 3:30 PM
72° (D)
74° (D) 11:30 PM
65° (A)
80° (A)
Sunday
5:00 AM
70° (C)
78° (B) 9:00 AM
70° (C)
76° (C) 3:30 PM
68° (B)
76° (C) 11:30 PM
65° (A)
80° (A)
3.
Press
SET
CLOCK
once. The display window will
show the hour only.
EXAMPLE:
4.
Press and hold either
TIME
FWD
or
TIME
BACK
until you
reach the correct hour and AM/PM designation (AM begins at midnight; PM begins at
noon).
5.
Press
SET
CLOCK
once. The display will show the
day of the week as an abbreviation (MON for
Monday, TUE for Tuesday, etc.).
6.
Press and hold either
TIME
FWD
or
TIME
BACK
Press
RUN
PRGM
During programming, if you don’t press any buttons for 5 minutes, the thermostat will enter the
HOLD mode and will maintain a constant temperature. The display will revert to the alternating time/
temperature display. To resume programming
after this happens, press
VIEW
PRGM
until you are at the
point where you stopped programming. Then you
may continue to enter your programs normally. If
you want to stop programming at any time, simply
press
RUN
PRGM
to resume program operation.
until you
reach the current day of the week.
7.
Select Heating and Cooling Temperatures
once. The display will show the
correct time and room temperature alternately.
1.
Press
2.
Press
SYSTEM
HEAT-OFF-COOL-AUTO
VIEW
TEMP
until HEAT is displayed.
once. The display will continue to
show HEAT. Below HEAT is the letter A,
representing the first programmed heating
25
3.
temperature (HEAT A). At the right of the
display is the currently programmed HEAT A
setting.
Press either
or
to change the
temperature to your selected HEAT A setting
(if you only want to program a temperature for
HEAT A, skip to step 7.)
4.
Press
5.
6.
Press
8.
Press
RUN
PRGM
Press
.
SYSTEM
HEAT-OFF-COOL-AUTO
until COOL is displayed.
VIEW
TEMP
once. The display will show
COOL and A, representing the first programmed cooling temperature (COOL A).
10. Press either
or
to change the
temperature to your selected COOL A setting
(if you only want to program a temperature for
COOL A, skip to step 13).
once. The letter A will change to
the letter B, representing HEAT B.
Press either
or
to change the
temperature to your selected HEAT B setting (if
you only want to program temperatures for
HEAT A and HEAT B, skip to step 7).
Repeat steps 4 and 5 to select HEAT C and
HEAT D temperature settings, if desired.
7.
26
VIEW
TEMP
9.
11. Press
VIEW
TEMP
once. Press
or
to set
your selected COOL B setting (if you only
want to program temperatures for COOL A
and COOL B, skip to step 13).
12. Repeat step 11 to select COOL C and COOL
D temperature settings, if desired.
13. Press
RUN
PRGM
.
Program Heating/Cooling Times and
Heating Temperatures
1.
Press
2.
Press
SYSTEM
HEAT-OFF-COOL-AUTO
VIEW
PRGM
until HEAT is displayed.
4.
once. MON, the abbreviation for
Monday, and the number 1, representing the
first heating/cooling period, will be displayed.
Also displayed are the currently programmed
start time for heating/cooling period 1 and the
currently programmed HEAT A, B, C, or D
temperature for heating/cooling period 1.
5.
this time period, press
EXAMPLE:
3.
To change the displayed start time to your
selected start time for Monday's period 1,
press
TIME
FWD
or
TIME
BACK
until your selected time
appears. The time will change in 15-minute
increments. The time that you program will
be the start time of Monday's period 1 for
both heating and cooling programs.
If the temperature displayed is not the HEAT
A, B, C, or D temperature you want for
Monday's period 1, press
or
(if
or
, the
you continue to press
display will alternately display the HEAT A, B,
C, or D temperatures you have already programmed).
If you want the fan to run continuously during
6.
FAN
ON
– AUTO
until PRG FAN
appears in the display (if you skip this step, the
fan will cycle automatically with the heating/
cooling system).
After selecting the desired heating temperature for Monday's heating/cooling period 1,
press
VIEW
PRGM
. The currently programmed start
27
7.
8.
time and heating temperature for Monday's
period 2 will be displayed.
Repeat steps 3 through 5 to select the start
time, heating temperature, and fan operation
for Monday's heating/cooling period 2.
Repeat steps 3 through 7 for Monday's heating/cooling periods 3 and 4.
The thermostat has a built-in COPY feature. This
feature automatically copies the heating and
cooling programs you select for Monday into
Tuesday's through Sunday's programs. If you
want to have the same programming every day,
after you program Monday's schedule, you simply
press
RUN
PRGM
to start the thermostat's programmed
operation. Every day will then use the same
program you set for Monday. You may also use
28
the
HOLD
COPY
button to copy any day's program into
any other day (see USING THE HOLD/COPY
BUTTON).
9.
To enter Tuesday's through Sunday's heating
HOLD
COPY
programs, use the
below, or press
ADV
DAY
button as described
until the correct day's
abbreviation appears in the display and repeat
the above steps to program each day's heating/cooling periods and heating temperatures.
10. When you have completed programming your
heating/cooling periods and heating temperatures, press
RUN
PRGM
.
Program Cooling Temperatures
1.
! CAUTION
If outside temperature is below 50°F, we
recommend that you remove the thermostat from the wall before proceeding with
the following steps to program cooling
temperatures. Personal injury and/or property damage could result from air conditioner compressor slugging. Fresh "AA"
alkaline batteries (such as Energizer®
brand) must be installed to perform offwall programming. Programming away
from the wall should prevent accidental
compressor operation. BE SURE TO
To program cooling temperatures for the heating/cooling periods you have already set, press
SYSTEM
HEAT-OFF-COOL-AUTO
2.
3.
Press
SYSTEM
HEAT-OFF-COOL-AUTO
VIEW
PRGM
once.
The Monday heating/
cooling period 1 start time you programmed
earlier will be displayed, along with the currently programmed COOL A, B, C, or D temperature.
Press
or
to display the COOL A,
B, C, or D temperature you want for Monday's
heating/cooling period 1. If you want the fan to
run continuously during this period, press
FAN
ON
PRESS
until COOL is displayed.
– AUTO
until PRG FAN is displayed.
UNTIL OFF IS DISPLAYED
BEFORE REATTACHING THE THERMOSTAT TO THE SUBBASE!
4.
Press
VIEW
PRGM
, then press
or
to
select Monday's COOL A, B, C, or D temperature for period 2. If you want the fan to run
29
FAN
continuously during this period, press
5.
ON
– AUTO
until PRG FAN is displayed.
Repeat step 4 for Monday's heating cooling
periods 3 and 4.
HOLD
COPY
button, or press
ADV
DAY
6.
Use the
7.
other days to program. Remember, once you
enter Monday's program, Monday's program
is automatically copied into Tuesday's through
Sunday's programs.
After you enter or copy heating and cooling
programs for all seven days, press
complete until
to choose
RUN
PRGM
HOLD
COPY
has been pressed twice.
NOTE
For most efficient programming, you should enter
both the heating and cooling programs for the day
you wish to copy FROM before using the COPY
function, since the COPY function copies the entire
day's programming to other days.
to
begin program operation.
Using the HOLD/COPY Button
You can use the button to copy any day's entire
heating/cooling program into any other day's pro-
30
gram. However, you must perform each copy
function separately. Each time you begin a COPY
operation, you must start with the day's program
you wish to copy FROM. A COPY operation is not
1.
Press
VIEW
PRGM
2.
Press
ADV
DAY
once.
until the day you want to copy
from is displayed. If you have not completed
programming for this day, do so before proceeding.
3.
Press
HOLD
COPY
display. A number from 1 to 7 will also be
displayed, representing the day you have selected to copy from (Monday is 1, Tuesday is
2, etc.). For example, if in step 2 you selected
to copy Wednesday's program, when you press
HOLD
COPY
4.
Press
, COPY 3 will be displayed.
ADV
DAY
CHECK YOUR PROGRAMMING
once. COPY will appear on the
to select the day you want to copy
Follow these steps to check your thermostat programming one final time before beginning thermostat operation.
Press
2.
Press and hold
6.
7.
Press
HOLD
COPY
. COPY will disappear from the
display, and the display will show the copied
heating/cooling time and temperature for the
day you copied to.
Repeat the above steps to copy any day's
programming into any other day's program.
Press
RUN
PRGM
HEAT-OFF-COOL-AUTO
until HEAT is displayed.
VIEW
PRGM
to view the heating/
cooling period times and heating temperatures for Monday.
the program TO.
5.
SYSTEM
1.
ADV
DAY
3.
Press
4.
Press and hold
5.
periods and heating temperatures for Tuesday.
Repeat steps 3 and 4 to review all remaining
days'programming. If you find an error in any
once to advance to Tuesday.
VIEW
PRGM
to view heating/cooling
to begin program operation.
31
day's programming, go back to the programming instructions to correct the error.
RUN
PRGM
6.
Press
7.
Press
8.
Repeat steps 2 through 5 to check cooling
temperatures.
9.
Press
.
SYSTEM
HEAT-OFF-COOL-AUTO
RUN
PRGM
until COOL is displayed.
to begin program operation.
NOTE
When you have completed programming, you may
set option switch group A (see TOTAL KEYPAD
LOCKOUT in the OPERATING FEATURES section).
Press
SYSTEM
HEAT-OFF-COOL-AUTO
until OFF is displayed. Reattach
thermostat to subbase. Turn on power to the
system. Then press
YOUR THERMOSTAT IS NOW COMPLETELY
PROGRAMMED AND READY TO AUTOMATICALLY PROVIDE MAXIMUM COMFORT AND
EFFICIENCY!
32
SYSTEM
HEAT-OFF-COOL-AUTO
to select the opera-
tion mode you want (HEAT, COOL, AUTO). Press
FAN
ON
– AUTO
cycling).
until FAN AUTO is displayed (automatic
QUESTIONS AND ANSWERS
1.
How can I permanently change a part of my
program?
Press
VIEW
PRGM
and
ADV
DAY
until you reach the
time/temperature schedule you want. Then
press
TIME
FWD
or
TIME
BACK
and
and
to
change the program. See PROGRAMMING
YOUR THERMOSTAT.
2.
How can I have no change in temperature
from one time period to another?
Simply select the same temperature for each
consecutive time period. For example, you
may select the same COOL A temperature for
period 2 as you did for period 1, which means
the temperature will not change from COOL A
when period 2 begins. See PROGRAMMING
YOUR THERMOSTAT.
3.
How can I finish my programming if the
display has already changed to time/temperature?
During programming, if no buttons are pressed
for five minutes, the thermostat will enter the
HOLD mode and maintain a constant temperature. The display will change to the time/
temperature mode. To resume programming,
press
VIEW
PRGM
and
ADV
DAY
until you return to the
point where you stopped programming. Then
you may continue to program the thermostat
normally. If you want to stop programming at
this point, press
RUN
PRGM
to start the normal
program function. See PROGRAMMING
YOUR THERMOSTAT.
33
4.
What happens if the electricity goes off or
is manually shut off?
If you have not installed 3 "AA" alkaline batteries, the display will go blank and the program
will be lost in approximately one minute. When
electricity is restored, the clock will reset itself
to 12:00 PM (noon) and the thermostat will
maintain a heating temperature of 64°F and a
cooling temperature of 82°F until you reenter
your program. Setpoint temperature will not
be displayed.
If fresh "AA" Energizer® alkaline batteries are
installed, the program will be maintained for
about one year with no 24vAC power present
to the thermostat. See OPERATING YOUR
THERMOSTAT.
5.
34
Why can’t I program the thermostat in the
AUTO mode?
The thermostat can only be programmed in
the HEAT and COOL modes. See PROGRAMMING YOUR THERMOSTAT.
6.
Why is the fan running constantly, regardless of system operation?
You have programmed the fan to run continuously during this program period. To override
the programmed fan, press
FAN
ON
– AUTO
until FAN
AUTO is displayed. To change the programming, see PROGRAMMING YOUR THERMOSTAT.
7.
What can cause the thermostat display to
freeze or go blank?
A completely blank display may indicate that
power has been lost to the thermostat and the
backup battery is also dead. However, if there
is power to the thermostat and the display is
blank or frozen, static discharge is probably
the cause.
During periods of low humidity (especially
during cold weather), you may feel or see a
spark discharge when you touch the thermostat. This may cause the program to be lost or
the thermostat to display incorrectly. To correct this, remove the thermostat from the wall
and disconnect the battery. Wait about two
minutes, then reconnect the battery. The
thermostat will revert to the factory preset
program until you reprogram the thermostat. If
you don’t want to reprogram the thermostat
immediately, press
SYSTEM
HEAT-OFF-COOL-AUTO
until OFF is dis-
played and replace the thermostat on the wall.
Then press
RUN
PRGM
to begin the factory preset
program. Or you may reprogram the thermostat, then replace it on the wall.
To prevent further static discharge problems,
touch another object to release static build-up
before touching the thermostat. See OPERATING YOUR THERMOSTAT.
8.
Why won’t the setpoint temperature go to
the temperature I want?
In the AUTO mode, the highest heating setpoint
temperature you select must be at least 1°F
lower than the lowest cooling setpoint temperature you select (for example, if 70°F is
your lowest selected cooling temperature, you
cannot select a heating temperature any higher
than 68°F). If such a conflict exists, you must
set the lowest cooling temperature higher in
order to set the heating temperature higher.
To set a lower cooling temperature, you must
select a lower heating temperature. See PROGRAMMING YOUR THERMOSTAT.
35
The display is flashing BATTERY. What
does this mean?
The "AA" batteries installed in the thermostat
are low and should be replaced with fresh "AA"
Energizer® alkaline batteries. See OPERATING YOUR THERMOSTAT.
11. The display shows a continuous (non-flashing) BATTERY. What does this mean?
The thermostat is not being supplied with
24vAC power. The thermostat is operating on
battery power alone. See OPERATING YOUR
THERMOSTAT.
10. The thermostat beeps every few minutes.
What does this mean?
The thermostat will beep every five minutes
when the batteries are low and need replacing. To override the beeping, press any button
on the keypad. The beeping will stop for 15
hours, then start again. You may again stop
the beeping by pressing any button on the
keypad. After turning the beep off three times,
the thermostat will quit beeping. However,
you risk losing your thermostat programming
if you continue to turn off the beep and do not
change the batteries. See OPERATING YOUR
THERMOSTAT.
12. Why won’t the compressor turn on, even
though the thermostat display is functioning normally?
Either the compressor lockout feature is in
operation or the thermostat is not currently
calling for cool. Wait about 5 minutes for the
compressor lockout to expire. If the system is
still not running, read the cautionary statement
at right. Then, if conditions permit, use the
button to move the temperature below
the setpoint temperature. See OPERATING
YOUR THERMOSTAT.
9.
36
! CAUTION
If the outside temperature is below 50°F,
DO NOT use the
button to move the
temperature below the setpoint temperature. Property damage may result due to
compressor slugging.
13. Why doesn’t the temperature change at the
time I programmed?
There may be a number of causes for this
situation. The following are primary reasons.
•
The EMR function is operating. The EMR
function will automatically bring on the system automatically to bring the temperature
to the selected level by the beginning of the
next program period. See OPERATING
YOUR THERMOSTAT.
•
•
You have programmed the incorrect day or
time. Check your programming (be sure
that the times you programmed are correct
AM or PM times). See PROGRAMMING
YOUR THERMOSTAT.
The thermostat is in the HOLD mode.
Press
•
RUN
PRGM
to start program operation.
See OPERATING YOUR THERMOSTAT.
The compressor lockout feature is operating; wait about 5 minutes for system to
begin running. See OPERATING YOUR
THERMOSTAT.
14. Why does the blower fan keep running
after the system has turned off?
• You have programmed the fan to run continuously during this period. See PROGRAMMING YOUR THERMOSTAT.
37
•
The blower delay feature is operating. This
energy saving feature continues to blow
conditioned air through the ducts after the
system has turned off, rather than letting
the air dissipate.
15. Why is the system turning on and off so
frequently (seldom)?
The anticipation setting is too low (high). To
change anticipation settings, see OPERATING YOUR THERMOSTAT.
16. Between heating and cooling seasons, I
want to turn my system off. Can I do this
without affecting my thermostat programming?
Any time you wish to turn your system off,
simply press
SYSTEM
HEAT-OFF-COOL-AUTO
until the display shows
OFF. This will not affect your thermostat’s
programming in any way. To turn the system
38
back on, press
SYSTEM
HEAT-OFF-COOL-AUTO
until HEAT, COOL,
etc. is displayed. The system will automatically begin operating according to the current
thermostat program, unless the thermostat is
in the HOLD mode. See OPERATING YOUR
THERMOSTAT.
17. I live in an area where daylight savings time
is observed. How do I change the thermostat clock twice a year without affecting
thermostat programming?
To change your clock, follow the instructions
for setting current time and day. See ENTERING YOUR PROGRAM. Thermostat programming is not affected when you change
the clock.
18. Do I have to reprogram my thermostat after
I change the batteries?
When the thermostat is on the wall and the
system has power, the thermostat is being
powered by a 24v AC source. If power is lost,
or if the thermostat is removed from the wall,
the program will be retained for approximately
one minute if there are no batteries installed
or if the installed batteries are dead. If you are
changing the batteries after seeing a flashing
BATTERY on the display, the installed batteries may be dead. If you remove the old
batteries and install fresh ones within one
minute, you should not lose your thermostat
programming. After installing new batteries,
follow the procedures in CHECK YOUR PROGRAMMING to determine whether your programming was maintained. If the thermostat
maintains programming, press
SYSTEM
HEAT-OFF-COOL-AUTO
until
OFF is displayed, put the thermostat back on
the wall, press
SYSTEM
HEAT-OFF-COOL-AUTO
to select the operating
mode you want, then press
RUN
PRGM
to start
program operation. If the program is lost,
reprogram the thermostat. See PROGRAMMING YOUR THERMOSTAT.
39
If you need further information on programming or operation, write to:
White-Rodgers Division, Emerson Electric Co.
9797 Reavis Road
St. Louis, MO 63123
Attn: Technical Service Department
Part No. 37-5092A
R
9140