Rimage DLN5200 User guide

Rimage DLN5200/DL5200™
User Guide
This manual provides the information needed to operate the DLN5200/DL5200 and identify the
parts. To set up and install your DLN5200/DL5200, refer to the Setup and Installation Guide.
Corporate Headquarters:
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
800 553 8312 (toll free US)
Service: +1 952 946 0004
(International)
Fax: +1 952 944 6956
European Headquarters:
Rimage Europe GmbH
Hans-Böckler-Straße 7
63128 Dietzenbach, Germany
Tel: +49-(0) 6074-8521-0
Fax: +49-(0) 6074-8521-21
CD and DVD Recording Software
Disclaimer
This Product, Software, or Documentation may be
designed to assist you in reproducing material in
which you own the copyright or have obtained
permission to copy from the copyright owner.
Unless you own the copyright or have permission
to copy from the copyright owner, you may be
violating copyright law and be subject to payment
of damages and other remedies. If you are
uncertain about your rights, you should contact
your legal advisor. If you are neither in possession
of the copyright nor have authorization from the
owner of the copyright, unauthorized copying of
CDs violates national and international legislation
and can result in severe penalties.
Rimage Corporation reserves the right to make
improvements to the equipment and software
described in this document at any time without any
prior notice. Rimage Corporation reserves the right to
revise this publication and to make changes from
time to time in the content hereof without obligation of
Rimage Corporation to notify any person or
organization of such revisions or changes.
This document may contain links to web sites that
were current at the time of publication, but may have
moved or become inactive since. This document may
contain links to sites on the Internet that are owned
and operated by third parties. Rimage Corporation is
not responsible for the content of any such third-party
site.
©2006, Rimage Corporation
Rimage™ is a trademark of the Rimage Corporation.
DLN5200/DL5200™ is a trademark of the Rimage
®
Corporation. Dell is registered trademark of Dell
®
Computer Corporation. FireWire is a registered
trademark of Apple Computer, Inc.
All other trademarks and registered trademarks are
the property of their respective owners.
Rimage DLN5200/DL5200
Support information
US, Asia/Pacific, Mexico/Latin America
Europe
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
Attn: Rimage Services
Rimage Europe GmbH
Hans-Böckler-Straße 7
63128 Dietzenbach, Germany
Service:
FAX: +49-(0) 6074-8521-21
Tel: +49-(0) 6074-8521-0
Rimage Europe Technical Website
North America: 800-553-8312
Asia/Pacific, Mexico/ Latin America: 952-946-0004
FAX: 952-946-6956
When you contact Rimage Services, please provide:
•
Unit serial number and software version.
•
Functional and technical description of the problem.
•
Exact error message received.
http://www.rimage.de/support.html
Select the appropriate Support link to
learn more. If you cannot find a solution
on our website, email Rimage Services,
Europe at support@rimage.de.
Learn more online
At www.rimage.com/support.html, you can experience Rimage’s world-class Support and
Services.
1. Select your product family.
2. Select your product.
3. Learn more on your
product page.
From your product page you can access:
•
Information about the latest software and firmware updates
•
Product specifications
•
Troubleshooting tips and FAQs
•
The latest documents
•
Printing tips
•
Current firmware and driver downloads
Contents
Contents
Introduction ...................................................................................... 1
Requirements ..................................................................................................1
Software requirements .......................................................................................... 1
Operating system requirements ............................................................................ 1
Media requirements............................................................................................... 1
Ribbon requirements ............................................................................................. 2
Label design requirements .................................................................................... 2
Networking ability ............................................................................................2
Identify the parts of the Rimage DLN5200/DL5200........................ 3
Front view.............................................................................................................. 3
Rear view - Rimage DLN5200............................................................................... 6
Rear view - Rimage DL5200 ................................................................................. 7
Operate the Rimage DLN5200/DL5200 ........................................... 9
Powering on .......................................................................................................... 9
Powering off ........................................................................................................ 10
Loading discs ...................................................................................................... 11
Removing or installing the front panel ................................................................. 11
Maintain the DLN5200/DL5200 ...................................................... 12
Preventive maintenance schedule ...................................................................... 12
Aligning the Everest printer ................................................................................. 12
Operate Gemini Utilities................................................................. 15
Starting Gemini Utilities ....................................................................................... 15
Changing the autoloader display name............................................................... 15
Enabling the beeper ............................................................................................ 15
Learn More ...................................................................................... 16
Rimage DLN5200/DL5200 specifications............................................................ 16
Operator panel error messages .......................................................................... 17
Technical support and product updates .............................................................. 19
Safety information ............................................................................................... 19
Safety Testing ..................................................................................................... 20
Rimage DLN5200/DL5200 Limited 1 Year Warranty/Guarantee ........................ 21
110768_D
i
Rimage DLN5200/DL5200
ii
Introduction
Introduction
This manual provides the information needed to operate the DLN5200/DL5200 and identify the
parts. To set up and install your DLN5200/DL5200, refer to the Setup and Installation Guide
included with your product.
The Rimage DLN5200 and DL5200 are robotic-controlled
autoloaders containing two recorders, a two-line display
panel, and an Everest Printer. The Rimage
DLN5200/DL5200 records and prints discs, then places
the finished discs in the output bin, or in one of the five
output trays.
The Rimage DL5200 requires a PC.
The Rimage DLN5200 has an embedded PC and is a
network ready device that receives orders from other
networked computers. You can also operate the Rimage
DLN5200 by attaching a monitor, keyboard, and mouse.
Rimage DLN5200/DL5200
Requirements
Software requirements
DLN5200
The Rimage DLN5200 ships with the correct software installed on the embedded PC. The
Rimage DLN5200 will operate only with the Rimage software installed on the embedded PC.
DL5200
The Rimage DL5200 will operate only with the Producer Software Suite.
Operating system requirements
DLN5200
The DLN5200 has an embedded operating system. The DLN5200 and software will function only
with the embedded operating system.
DL5200
The Rimage DL5200 and the Producer Software Suite run only on Windows 2000, Windows XP,
and Windows Server 2003.
Media requirements
For media requirements, refer to the Everest Printer User Guide.
110768_D
1
Rimage DLN5200/DL5200
Ribbon requirements
For ribbon requirements, refer to the Everest Printer User Guide.
Label design requirements
For label design requirements, refer to the Everest Printer User Guide.
Networking ability
Using the Rimage Producer Software Suite, you can submit orders to the Rimage DL/DLN5200
from a networked PC or Macintosh. For more information, refer to the Rimage Advanced Setup
Guide at http://www.rimage.com.
2
110768_D
Identify the parts of the Rimage DLN5200/DL5200
Identify the parts of the Rimage
DLN5200/DL5200
This section describes the Rimage DLN5200/DL5200 hardware and its features.
Front view
Printer
Operator
Button
Transfer
Slides
Operator
Panel
Everest
Output
Trays
Lift
Arm
Recorders
PC Power
Button
Supply Bin
Output
Note: The PC power button is on only the Rimage DLN5200.
110768_D
3
Rimage DLN5200/DL5200
Operator panel
Operator Panel
The operator panel has a two-line LCD
display that informs you of operations or any
conditions that require resolution.
The Rimage DLN5200 displays the name of
the embedded PC or product name after it
initializes. The computer name is displayed by
default. This is helpful in identifying the
embedded PC on the network. Refer to the
Gemini Utilities section on page 15 to see
other options.
Operator button
Operator Button
Operator Panel
The operator button is a push button used to
open and close the print drawer. The operator
button is only accessed by removing the front
panel.
Press the operator button to open the print
drawer. Press it again to close the print
drawer.
Beeper
The Rimage DLN5200/DL5200 has a beeper that sounds when user intervention is required.
Read the condition on the operator panel or at the client application and take appropriate action
to correct the problem. To stop the beeping, open the supply door.
To change the number of beeps or to disable the beeper, refer to the Enabling the beeper section
on page 15.
Lift Arm
Lift arm
The lift arm picks and transports the discs.
There are three gripper fingers, located on the
underside of the lift arm, that hold the disc.
You can press a disc up onto the gripper
fingers to check printer alignment or for other
reasons. You can remove the disc by pulling
the disc down away from the lift arm.
Disc present sensor
The disc present sensor is depressed when a
disc is held by the gripper fingers. It is used to
detect the supply bin, recorder trays, or the
print drawer.
4
Gripper
Fingers
Disc Present Sensor
110768_D
Identify the parts of the Rimage DLN5200/DL5200
Output trays
The Rimage DLN5200/DL5200 is configured
with five output trays and an output bin. When
a disc is recorded and printed, the lift arm
moves the disc to the output bin or one of the
output trays. The disc slides out to the end of
the tray. The sensor located on each output
tray detects if a disc is in the output tray. The
output trays are numbered 1 - 5, with 1
located at the top.
Output
Trays
Output Bin
Output bin
The output bin receives finished and/or failed
discs. The output bin holds up to 75 discs.
To remove discs from the output bin, hold
the output bin with one hand while moving the
bin latch up and then lower the bin.
Note: Each time you fill the supply bin,
remove the completed discs from the
output bin so the output bin does not
become full.
To lower the output bin, hold the output bin
while lifting the latch. Then lower the output
bin.
To raise the output bin into position, lift the
output bin and then pull the bin latch down to
lock it in place.
Bin Latch
p Caution: Do not use the latch to raise the
output bin!
110768_D
5
Rimage DLN5200/DL5200
Rear view - Rimage DLN5200
Printer USB Cable
Printer Control
Cable
Printer Power
Cord
PC Power
Cord
Serial Cable
Mouse Cable
Network
Connection
Keyboard
Cable
USB cable
Power
Cord
Monitor
Cable
6
110768_D
Identify the parts of the Rimage DLN5200/DL5200
Rear view - Rimage DL5200
Printer Control Cable
Printer USB Cable
Printer Power Cord
Printer Control Cable
USB Cable
FireWire Cable
AC Power Cord
Note: The 9-Pin serial connector is not used.
110768_D
7
Rimage DLN5200/DL5200
PC power switch
The PC power switch supplies power to the embedded PC and autoloader.
Note: The PC power switch is on only the Rimage DLN5200.
Main power switch
The main power switch is used to apply power to the entire system (printer, embedded PC, and
the autoloader) The Rimage DLN5200 requires both power switches to be switched to the ‘on’
position.
DL5200
DLN5200
PC Power Switch
Main Power Switch
8
Main Power Switch
110768_D
Operate the Rimage DLN5200/DL5200
Operate the Rimage DLN5200/DL5200
Powering on
Before you begin:
Set up the Everest printer. For more information, refer to the Everest Printer Unpacking and
Setup Guide.
Powering on the Rimage DLN5200
1. Press the PC power switch to the ‘on’
position.
PC Power
Switch
2. Press the main power switch to the ‘on’
position.
Note: After pressing the main power
Main Power
Switch
switch to the ‘on’ position, the Everest
printer initializes.
3. Press the PC power button to power on
the embedded PC. When the DLN5200
autoloader has completed the initialization,
the operator panel displays RIMAGE
DLN5200 READY.
PC Power
Button
Powering on the Rimage DL5200
Before powering on the computer attached to the
DL5200, press the main power switch to the ‘on’
position.
When the DL5200 autoloader has completed the
initialization, the operator panel displays RIMAGE
DL5200 READY.
110768_D
Main Power
Switch
9
Rimage DLN5200/DL5200
Powering off
Powering off the Rimage DLN5200
1. Close all open applications.
2. To shut down the software, Windows, and the
embedded PC, briefly press the PC power button.
p Caution: Do not press and hold the PC power
button. If you press and hold the PC power button,
the embedded PC will not shut down properly. This
may cause data loss or corruption.
PC Power Button
Note: Power down takes approximately 30 seconds.
3. After waiting approximately 30 seconds for the PC to
power down, press the main power switch to power off
the DLN5200.
Power off the Rimage DL5200
1. Close all open applications.
2. Press the main power switch to power off the Rimage DL5200.
Note: When you start the Rimage DL5200 again, you must first power on the DL5200
and then power on the attached computer so the recorders are recognized.
10
110768_D
Operate the Rimage DLN5200/DL5200
Loading discs
The supply bin can be loaded with 50
discs. Use thermal printable discs
compatible with the Everest printer.
1. Open the supply door.
2. Remove the supply bin.
Supply
Door
3. Place the discs in the supply bin with
the recording side facing down.
- Important! Hold the discs by the
edge. Fingerprints affect print
quality.
Supply Bin
4. Place the supply bin on the base
plate.
5. Rotate the supply bin until it drops
into the notches.
6. Close the supply door.
Notch
Base Plate
Removing or installing the front panel
Removing the front panel
Front Panel
Grasp the sides of the front panel and pull out.
Note: The front panel has four pins that
are held in with retaining clips.
Installing the front panel
Align the pins to the retaining clips and press
in the front panel.
110768_D
11
Rimage DLN5200/DL5200
Maintain the DLN5200/DL5200
The procedures in this section will help keep your DLN5200/DL5200 in optimum operating
condition.
Preventive maintenance schedule
Maintenance Procedure
Schedule
Cleaning the Rimage
DLN5200/DL5200
Once a week. Using a damp, lint free cloth, remove dust from
the autoloader and surrounding work area.
Aligning the Everest printer
On installation and as needed. Refer to the instructions
below.
Aligning the Everest printer
When the Everest printer is installed, it may need to be aligned to the lift arm.
Tools Needed: T25 Torx driver
Before you begin:
Power on the Rimage DLN5200/DL5200 autoloader. Wait for the unit to initialize.
Note: The Everest printer takes 2 to 3 minutes to complete the initialization.
1. Select Diagnostic 4, jog lift diagnostic.
a. Press and hold the operator button to place the unit in diagnostics mode. The operator
panel indicates when to release the button.
b. When the operator panel displays 01 CYCLE OUTPUTS DIAGNOSTIC, press the
operator button four times and hold on the fourth press. This selects the JOG LIFT
DIAGNOSTIC TEST. The lift arm moves down toward the print drawer as the print
drawer opens.
c.
When the operator panel prompts you to place a disc, place a disc on the print pad.
2. Check the printer alignment.
12
a. Press the operator button to move
the lift arm closer to the print pad.
Lift Arm
b. Press the operator button again
and the lift arm moves down and
picks up the disc.
Disc
c.
Print Pad
Manually rotate the lead screw
counterclockwise to move the lift arm
down to the print pad.
Print Drawer
110768_D
Maintain the DLN5200/DL5200
3. Check the disc alignment.
To see if the disc is centered, observe
the gap between the edge of the disc and
the raised edges as shown by the
arrows.
If the disc is not centered side to side on
the print pad, continue to step 4.
Print Pad
If the side to side alignment is correct, go
to step 5.
Lead Screw
4. If necessary, perform a side to side
alignment.
Front to back Alignment Screw
a. Loosen the two side to side
alignment screws.
b. Slide the printer until the side gaps
are equal.
- Important! Slide the entire
printer, not the drawer.
c.
Tighten the two side to side
alignment screws.
Side to side Alignment Screws
110768_D
13
Rimage DLN5200/DL5200
5. If necessary, perform a front to back
alignment.
Disc Retainer
a. Turn the front to back alignment
screw until there is a 1/16” (1.5mm)
gap between the front edge of the
disc and the raised edge of the disc
retainer.
# Tip: You can use the T25 Torx
driver, or 5/32” Allen wrench, to
turn the front to back alignment
screw.
b. When the printer is aligned, rotate
the lead screw to raise the lift arm
up about 1.0” (2.5 cm).
Gap Distance
6. Exit diagnostics.
a. Press and hold the operator
button to exit diagnostic 4. The
disc is lifted up to the top output
tray and released.
b. Press the operator button
fourteen times and hold on the
last press to exit diagnostics.
c.
14
Press the operator button one
more time to close the print
drawer.
Lift Arm
Print Pad
Lead Screw
110768_D
Operate Gemini Utilities
Operate Gemini Utilities
The Rimage Producer Software Suite includes an application called Gemini Utilities, which is
used to update the autoloader firmware. It may also be used to change the display name of the
Rimage DLN5200/DL5200 and to enable the beeper. The Rimage DLN5200 displays the
computer name on the operator panel, which is helpful to identify the computer on the network.
# Tip: To access Gemini Utilities, use the remote desktop connection from a networked PC, or
connect a monitor, keyboard, and mouse to the DLN5200.
Starting Gemini Utilities
1. Close all open applications and stop all Rimage
Services.
Note: Refer to your Rimage Software online
help for additional information.
2. Navigate: Start > Programs > Rimage > Utilities
> Gemini Utilities. Gemini Utilities opens.
Note: When the desired tasks are complete,
restart the Rimage Services.
Changing the autoloader display name
Use Gemini Utilities to enter the name displayed on the operator panel.
1. Select the Override Name checkbox.
2. Clear the Use Computer Name checkbox.
3. In the Display Name field, enter the new name.
4. To update the firmware with the new name, select Set DiscLab Params.
Enabling the beeper
You can change the number of beeps that occur when there is an error.
1. From the # of Beeps on Fault dropdown list, select the number of beeps you wish to hear
when there is an error.
# Tip: To disable the beeper, set the number to zero.
2. Select Set DiscLab Params to update the firmware.
110768_D
15
Rimage DLN5200/DL5200
Learn More
Rimage DLN5200/DL5200 specifications
Note: For printer specifications, refer to your Everest Printer User Guide or PrismPlus! Printer
User Guide.
Rimage DLN5200
Two disc recorders, Rimage DLN5200 autoloader, an Everest printer,
a network-ready embedded PC, and Rimage software.
Rimage DL5200
Two disc recorders, Rimage DL5200 autoloader, an Everest printer,
and Rimage software.
Input Bin Capacity
One removable 50-disc bin.
Output Capacities
Five single-disc output trays and one 75-disc output bin.
Rimage DLN5200
(Embedded PC)
Celeron D 340 processor with 533Mhz Front Side Bus
512MB DDR2-400, SDRAM
Windows XP Embedded with Service Pack 2
Two 36 GB, Serial ATA, 10,000 RPM, 8 MB cache, Hard Drives
Rimage DL5200 PC
requirements
Pentium 4 2.8 GHz, 512MB L2 Cache , 800MHz FSB
512MB DDR2-200, 400Mhz Bus
Microsoft Windows® 2000 Professional Service Pack 4, Microsoft
Windows XP Professional Service Pack 1or 2, Windows Server 2003
Rimage recommend 4 hard drives – One for the OS, one for the
Rimage System Folder, and two for caching (one for each recorder).
One open PCI slot for the provided FireWire®/USB card.
Height
23.25 inches (59.1 cm)
Width
14.5 inches (36.8 cm)
Allow an additional 2.4 inches (6.1 cm) of space for the door to swing
open.
Depth
23.5 inches (59.1 cm)
Allow an additional 2.5 inches (6.4 cm) for cabling in the rear of the
autoloader.
DLN5200 Weight
51 lbs (23.2 kg) without Everest printer, 95 lbs. (43.2 kg) with Everest
printer.
DL5200 Weight
44.5 lbs (20.2 kg) without Everest printer, 88.5 lbs. (40.2 kg) with
Everest printer.
Power
100 – 240VAC, 60/50 Hz, 4.7 – 3.7 Amps
Operating
Temperature
60° – 80º F (15.5º – 26.7° C)
Humidity
40–80% non-condensing
16
110768_D
Learn More
Operator panel error messages
These messages may display on the operator panel.
CLAMP FAILURE – The Everest printer tried to clamp a disc but it failed. Check the alignment of
the printer to the gripper fingers. Refer to Aligning the Everest printer on page 12. Also, check the
discs to ensure they are not warped.
SYSTEM PAUSED CHECK DOOR/BIN – The Rimage DLN5200/DL5200 stopped all movement
because the door is open.
NO PRINTER DETECTED – The printer serial cable is not connected to the autoloader, or the
printer has no power. Check the cabling and the mode switch setting. The mode switch must be
set to 1.
NO DISPENSER DETECTED – The dispenser (the mechanism that contains the output trays,
transfer slides, and dispenser circuit board) was not detected. Check the cable connection to the
dispenser circuit board or the connection to the internal circuit board.
OUTPUT TRAY X OUTPUT FAIL – A disc was dropped into the X output tray and the tray sensor
detected that the disc did not slide past the tray sensor. This stops the autoloader from further
movement.
SUPPLY BIN NO MEDIA – The supply bin is empty. If the supply bin is not empty, perform
diagnostic 3 to recalibrate the lift arm positioning.
Everest printer errors
Error messages from the Everest printer that may display on the Rimage DLN5200/DL5200
operator panel include:
EVEREST PRINTER #1 NOT LOCKED – Open the Everest printer cover and close latch 1.
EVEREST PRINTER #2 NOT LOCKED – Open the Everest printer cover and close latch 2.
EVEREST PRINTER #3 NOT LOCKED – Open the Everest printer cover and close latch 3.
EVEREST PRINTER CLAMPING FAILURE – Ensure that the printer is aligned. Refer to Aligning
the Everest printer on page 12. Also, check the discs to ensure they are not warped.
EVEREST PRINTER CLOSING ERROR – The printer drawer could not close. Check the printer
alignment and ensure that the printer drawer is not obstructed.
EVEREST PRINTER COVER OPEN – Close the Everest printer cover.
EVEREST PRINTER DATA ERROR – The label file may be corrupt or the label file was built by
the wrong printer driver. Check the selected printer driver, rebuild the label, and try again.
EVEREST PRINT DRAWER ENCODER – Remove the shipping screw. If the shipping screw is
removed and you continue to receive this error, contact Rimage support.
EVEREST PRINTER HALOGEN LAMP OUT – The halogen lamp in the Everest printer must be
replaced.
EVEREST PRINTER INK RIBBON GONE – The print ribbon is not installed. Install a print ribbon.
EVEREST PRINTER INK RIBBON SENSR – Clean the print ribbon sensor or contact Rimage
support.
EVEREST PRINTER LOWER P.H. ERROR – Contact Rimage support.
EVEREST PRINTER NO MEDIA – The lift arm could not pick a disc from the printer tray. There is
no disc on the print pad or the printer is not aligned to the gripper fingers. The gripper solenoid
may not be working or may need adjustment.
110768_D
17
Rimage DLN5200/DL5200
EVEREST PRINTER OPENING ERROR – The print drawer may be obstructed. Ensure that the
printer is seated properly on the printer mounting plate and ensure that the printer is aligned.
EVEREST PRINTER RAISE P.H. ERR. – Contact Rimage support.
EVEREST PRINTER RETRANSFER OUT – The retransfer ribbon is at the end of the roll and a
new retransfer ribbon must be installed.
EVEREST PRINTER RETRANSFER GONE – The retransfer ribbon is not installed. Install a
retransfer ribbon.
EVEREST PRINTER RIBBON OUT – The print ribbon is out and a new print ribbon must be
installed.
EVEREST PRINTER R.T. DOWN SENSOR – Contact Rimage support.
EVEREST PRINTER R.T. UP SENSOR – Contact Rimage support.
EVEREST PRINTER R.T. ROLLER FAIL – Contact Rimage support.
EVEREST PRINTER R.T. MOTOR FAIL – Contact Rimage support.
EVEREST PRINTER R.T. THERMISTOR – The retransfer roller thermister must be replaced.
Contact Rimage support.
EVEREST PRINTER SET SWITCH TO 1 – The Rimage autoloader detected the mode switch on
the Everest Printer is not set to position 1. Change the mode switch to position 1. After changing
the mode switch, the printer must be reinitialized. Use the following instructions:
•
If the autoloader is a DL5200, use the main power switch to power off the system. After ten
seconds, switch the main power switch to the ‘on’ position. Restart the PC so it will recognize
the recorders.
•
If the autoloader is a DLN5200, use the PC power button to power off the system. Switch off
the main power switch. Then switch on the main power switch and press the PC power
button to restart the system.
EVEREST PRINTER P.H. THERMISTOR – The print head thermister must be replaced. Contact
Rimage support.
18
110768_D
Learn More
Technical support and product updates
Support for the DLN5200/DL5200 autoloader is available through your authorized reseller.
- Important Be sure to register your Rimage DLN5200/DL5200 autoloader online or complete
and return the registration card so we can notify you of upgrades as they become available.
Safety information
This manual and the indications on the product allow proper and safe operation. The indication
marks below help protect you and other persons from injury, and equipment from damage.
n Warning!
According to ANSI (American National Standards Institute) standards, a warning is
used to indicate situations that could result in bodily injury to personnel operating or
maintaining the equipment.
p Caution:
Indicates that failure to observe this guideline could result in loss or damage to the
equipment, product, software, or data.
Safety precautions
To ensure safety, please read the precautions in the User Guide and familiarize yourself with their
meaning before using the equipment.
n Warning: The laser beam used by this CD-R or DVD-R recorder is a class 1 laser and can
be harmful to the eyes. Do not attempt to open the recorder. Do not attempt to view the
laser beam.
n Warning: Never use any optical instrument in conjunction with this unit. To do so will greatly
increase the hazard to your eyes.
n Warning: Please observe all warning and caution labels to ensure safety of personnel.
n Warning: Replace all fuses with the same voltage and current ratings to maintain UL safety
approvals.
n Warning: Use the supplied AC power cord, or use a safety agency-approved power cord.
p Caution: Any equipment that has AC line voltage, or low DC voltages, such as switches,
power supplies, fuses, fans, non-stepper motors, must be replaced with Rimage–approved
components to maintain the safety approval issued by UL.
p Caution: The DLN5200 model contains a lithium battery. There is a risk of explosion if the
battery is replaced by an incorrect battery. Dispose the old battery according to the
manufacture’s instructions included with the battery package.
110768_D
19
Rimage DLN5200/DL5200
Safety Testing
Product name: Rimage DLN5200/DL5200
Model:
•
DLN5200: RAS15E
•
DL5200: RAS15
Notice for USA
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This product complies with UL 60950-1.
Notice for Canada
C
This Class B digital apparatus complies with Canadian ICES-003 Issue 3:1997. Cet
appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
This product complies with CAN/CSA-C22.2 No. 60950-1-03
Notice for Europe
This product is in conformity with the EMC Directive (89/336/EEC) and the Low-Voltage
Directive (73/23/EEC) through compliance with the following European standards:
EN 55022: 1998 + Amd 1: 2000 Amd 2:2003 Class B Limit; EN 55024: 1998; EN 610003-2:1995; EN 61000-3-3:1995 + Amd 1: 2001; IEC 60950-1 (2001). The CE mark has
been affixed in accordance with the CE Marking Directive 93/68/EEC.
20
110768_D
Learn More
Rimage DLN5200/DL5200 Limited 1 Year Warranty/Guarantee
Rimage warrants, to the original end user only, that all non-consumable parts of the Rimage
DLN5200/DL5200 of automated products will be free from defects in material or workmanship for 12 months,
according to the following terms:
•
Rimage will replace or repair, at Rimage's discretion, any non-consumable parts found defective within
the Warranty period.
•
Valid from the date Rimage ships the product to you.
•
Factory depot repair:
ƒ
To Rimage’s location in Minnesota from a location within the US or Canada with a typical response
of 15 business days.
ƒ
To Rimage’s location in Germany from a location in Europe with a typical response of 15 business
days.
ƒ
To Rimage Minnesota from a location that is not in the US or Canada with a typical response of up
to 25 business days.
•
Advanced Replacement or faster response Maintenance Contracts are available for an additional fee.
•
Rimage will pay ground service freight charges for components shipped to you.
The use of non-Rimage certified parts may void this warranty.
This Warranty Does Not include the following:
•
Work done at the customer's location, or customer's loss of data.
•
Shipment costs of equipment or components returned to the Rimage factory.
•
Equipment malfunctions as a result of repairs made by technicians who are not authorized or certified
by Rimage.
•
Repairs and associated costs to restore the equipment to its original or factory authorized upgraded
state where software that is not provided by Rimage or its affiliates was installed on the system and
such unauthorized software caused operational issues.
•
Equipment or parts that were tampered with, misused, neglected, or that were modified in any respect
without the written consent of Rimage.
•
Equipment or parts that have been damaged due to shipping or accidents, or damaged by lightning,
storms, water, or power surges.
•
Printer consumables including ribbons, retransfer ribbons, or print head.
You may not assign this Warranty without Rimage's written consent. Rimage is the intended beneficiary of
this Warranty; if there is any inconsistency between this Warranty and any other agreement included with or
relating to Rimage products, this Warranty shall govern. If any term of this Warranty is illegal or
unenforceable, the legality and enforceability of the remaining provisions are not affected or impaired. This
Warranty is to be interpreted under the laws of the State of Minnesota, without giving effect to conflict of law
rules.
Rimage must receive written notice of any claimed failure to perform or malfunction within five (5) days after
such failure or defect is first observed. For warranty service, call Rimage at (952) 946-0004. For Europe, call
+49-(0) 6074-8521-0. The Limited Warranty set forth above is Rimage's only Warranty in connection with the
Rimage DL5200\DLN5200 and Everest products. All other Warranties, whether written or oral, express or
implied, contractual or statutory, including, but not limited to any Warranties of merchantability or fitness for
any particular purpose are specifically excluded and disclaimed. In no event shall Rimage's liability under
this Warranty exceed the obligation to repair or replace, at Rimage's discretion, a Warranted product, and,
without limiting the foregoing, Rimage's liability under this Warranty shall not exceed the cost of the covered
product.
110768_D
21