Siemens SIMATIC TIWAY 1 Technical data

 !
"# $
% $&!'!'
""$(
)* +
Copyright 1994 by Siemens Industrial Automation, Inc.
All Rights Reserved — Printed in USA
Reproduction, transmission or use of this document or
contents is not permitted without express consent of
Siemens Industrial Automation, Inc. All rights, including rights
created by patent grant or registration of a utility model or
design, are reserved.
Since Siemens Industrial Automation, Inc. does not possess
full access to data concerning all of the uses and applications
of customer’s products, we do not assume responsibility either
for customer product design or for any infringements of patents
or rights of others which may result from our assistance.
Technical data is subject to change.
We check the contents of every manual for accuracy at the
time it is approved for printing; however, there may be
undetected errors. Any errors found will be corrected in
subsequent editions. Any suggestions for improvement are
welcomed.
MANUAL PUBLICATION HISTORY
SIMATIC TIWAY 1 Unilink Adapter Installation and Operation Manual
Order Manual Number: PPX:TIWAY–8106–2
Refer to this history in all correspondence and/or discussion about this manual.
Event
Date
Description
Original Issue
Second Edition
Errata 1
04/86
05/86
10/86
Third Edition
Fourth Edition
02/87
04/94
Original Issue (2494092–0001)
Second Edition (2494092–0002)
Correct pages 4-17 – 4-20, 5-9 – 5-12, B-1 – B-2.
(2599181–0001)
Third Edition; incorporates Errata 1 (2494092–0003)
Fourth Edition (2494092–0004)
LIST OF EFFECTIVE PAGES
Pages
Cover/Copyright
History/Effective Pages
iii — v
1-1 — 1-2
2-1 — 2-2
3-1 — 3-6
4-1 — 4-28
5-1 — 5-17
A-1 — A-2
B-1 — B-3
Registration
Description
Fourth Edition
Fourth Edition
Fourth Edition
Fourth Edition
Fourth Edition
Fourth Edition
Fourth Edition
Fourth Edition
Fourth Edition
Fourth Edition
Fourth Edition
Pages
Description
Contents
Chapter 1
Manual Overview
Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2
Introduction to the Unilink Adapter
Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unilink Adapter/PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3
Chapter 4
3-3
3-4
3-6
3-6
Installing Your Unilink Adapter
Specifications and Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector Wire Gauges – Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
2-2
2-2
Hardware Description
The Personality Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adapter Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Loopback Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
4.2
4.3
1-1
1-2
1-2
4-2
4-3
4-28
Diagnostic Tests
Status Display Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Tests: With or Without PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dipswitches 1 and 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED Operation During Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2
5-4
5-5
5-6
5-7
5-8
5-9
5-14
5-17
Appendix A
Schematic of the RS-232/423 Loopback Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic of the Mixed Media Loopback Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix B
A-1
A-2
Unilink Adapter Specifications
General Specifications and Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External I/O Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
B-1
B-2
iii
List of Figures
Figure 2-1 The Unilink Adapter and PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-2 Network Interfacing with the Unilink Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-2
Figure 3-1
Figure 3-2
Figure 3-3
Figure 3-4
UNILINK Adapter and Hardware – PIM Installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unilink Adapter – Access Door Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unilink Adapter – Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1
3-2
3-3
3-4
Figure 4-1
Figure 4-2
Figure 4-3
Figure 4-4
Figure 4-5
Figure 4-6
Figure 4-7
Figure 4-8
Figure 4-9
Figure 4-10
Figure 4-11
Figure 4-12
Figure 4-13
Figure 4-14
Unilink Adapter – Outside Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adapter Dimensions – Brackets Installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Required Clearances for Proper Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rack-Mount Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Surface-Mount Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unilink Adapter Ports 1 and 2 – Local Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unilink Adapter Ports 1 and 2 – RS-232/423 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unilink Adapter Ports 3 and 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Null Modem Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External I/O Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connections to the External I/O Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unilink Adapter Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIM Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-15
4-17
4-18
4-20
4-21
4-25
4-26
Figure 5-1
Figure 5-2
Figure 5-3
Figure 5-4
Figure 5-5
Figure 5-6
Adapter LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADAPTER GOOD LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LEDs 2 through 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The RESET Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dipswitches 1 and 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dipswitch 2, Position 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2
5-3
5-4
5-5
5-6
5-7
Figure A-1 RS–232/423 Loopback Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure A-2 Mixed Media Loopback Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-1
A-2
iv
Contents
List of Tables
Table 3-1 Factory-Supplied Loopback Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-6
Table 4-2
Table 4-3
Table 4-4
Table 4-5
Table 4-6
Table 4-7
RS-232-C D-Connector Pin Assignments/Ports 1 and 2 . . . . . . . . . . . . . . . . . . . . . . . . . .
9-Pin Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Output Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Input Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unilink Adapter Voltage Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector Wire Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-16
4-19
4-22
4-23
4-24
4-28
Table 5-1
Table 5-2
Table 5-3
Table 5-4
Unilink Adapter Diagnostic Test Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USER Diagnostic Tests and Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RESET Diagnostic Tests and Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Possible Adapter Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7
5-12
5-15
5-17
Table B-1 External Output Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-2 External Input Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B-2
B-3
Contents
v
Chapter 1
Manual Overview
This manual contains the basic information you will need to install, test,
and troubleshoot the Siemens Industrial Automation, Inc. Universal
Network Adapter (called the SIMATIC “Unilink Adapter” or the
“Adapter” throughout the remainder of this manual).
Subjects covered include:
Organization
•
Dimensions
•
Functions
•
Mounting configurations
•
Electrical specifications
•
Connector pin assignments
•
Built–in diagnostic tests
•
Troubleshooting
This manual is organized as follows:
•
Chapter 2 – Introduction to the Unilink Adapter. This chapter contains
an overview of the Adapter’s function as an interface to SIMATIC
TIWAY I, the Siemens Industrial Automation, Inc. Local Area
Network. The Adapter’s general capabilities are also listed.
•
Chapter 3 – Hardware Description. This chapter describes the Adapter
hardware components, including the PIM, the Loop–back Connectors,
Ports 1 through 4, the External I/O Terminal, and the AC Power
Terminal.
•
Chapter 4 – Installing Your Unilink Adapter. This chapter describes
the installation procedures for the Unilink Adapter, and also provides
the information required to properly install cables, connectors,and
terminals.
•
Chapter 5 – Diagnostic Tests. This chapter describes the diagnostic
tests available to you, and lists test procedures and error codes as well.
Also included is a table giving possible Adapter malfunctions and the
corrective action recommended.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Manual Overview
1-1
•
Appendix A contains schematic diagrams of the Unilink Adapter
Loopback Connectors.
•
Appendix B lists the Adapter Specifications.
•
Index
References
Additional information covering both the TIWAY I theory of operation and
the capabilities of the Unilink Adapter for your specific application can be
found in the SIMATIC TIWAY Systems Manual (PPX:TIWAY–8101–x) and
the appropriate Personality Interface Module (PIM) User’s Manual.
Technical
Assistance
If you have any questions regarding the installation and operation of this
equipment, or if more information is desired, contact your Siemens
Industrial Automation, Inc. distributor or sales agent. If you need
assistance in contacting your distributor or sales office in the United States,
call 800–964–4114. If additional technical assistance is needed, call Siemens
Industrial Automation, Inc. Technical Services Group in Johnson City,
Tennessee at 615–461–2522.
1-2
Manual Overview
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Chapter 2
Introduction to the Unilink Adapter
The Unilink Adapter and Personality Interface Module (PIM) are shown in
Figure 2-1. Together they provide a tailored interface between a TIWAY I
Local Area Network and an RS-232/RS-422/RS-Unilink423 device (referred
to in the remainder of this manual as the “attached device”). This interface
enables the attached device to communicate over TIWAY I as shown in
Figure 2-2.
Figure 2-1 The Unilink Adapter and PIM
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Introduction to the Unilink Adapter
2-1
Interfaces
The Unilink Adapter provides the hardware required for the physical
interface between the attached device and TIWAY I. The PIM provides the
software that customizes the interface to the attached device. Any Unilink
Adapter can be reconfigured to function with a new or different attached
device by changing the PIM.
Figure 2-2 Network Interfacing with the Unilink Adapter
Unilink
Adapter/PIM
2-2
The Unilink Adapter and this manual are common to all applications of the
Adapter. The PIM is developed and purchased separately, and its features
depend on the tasks your Adapter must fulfill. PIM documentation is
provided in your PIM User’s Manual.
Introduction to the Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Chapter 3
Hardware Description
The purpose of this chapter is to describe the following hardware
components of the Unilink Adapter:
1.
The metal case, door, brackets, and associated hardware.
2.
The PIM.
3.
The Adapter Connectors.
4.
The Loopback Connectors.
Figure 3-1 UNILINK Adapter and Hardware – PIM Installed
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Hardware Description
3-1
The Metal Case
and Door
The Unilink Adapter’s metal case provides bracket-attachment bolt holes for
secure factory-floor installation.
As shown in Figure 3-2, the Unilink Adapter’s hinged door provides access
to six LEDs, the RESET Switch, the Dipswitches, and the Personality
Interface Module (PIM). Both the PIM label and the ADAPTER GOOD LED
are visible when the Adapter’s door is closed. The door and case are
designed to ground you when you touch them, discharging static electricity
before you handle any of the Adapter’s internal components. The door
should be closed securely when not in use.
Figure 3-2 Unilink Adapter – Access Door Open
3-2
Hardware Description
TIWAY 1 Unilink Adapter Installation
and Operation Manual
The Personality
Interface Module
The Personality Interface Module (PIM) configures the Unilink Adapter to
interface with the attached device, and is purchased separately.
Figure 3-3 The PIM
The PIM is easily removed and replaced when the Adapter’s door is open.
The PIM’s label is visible at all times.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Hardware Description
3-3
Adapter
Connectors
The following connectors are provided on the Adapter’s rear panel:
1.
Four D-type connectors.
2.
One External Input/Output (I/O) Connector.
3.
One Power Connector.
Figure 3-4 Unilink Adapter – Rear Panel
3-4
Hardware Description
TIWAY 1 Unilink Adapter Installation
and Operation Manual
NOTE: Unilink Adapter PPX:500–7111 is shown in Figure 3-4. The rear
panel on your Adapter may differ. Connector configurations by model
number follow, and Chapter 4 has detailed information on all Adapter
connectors.
Ports 1 and 2. Adapter PPX:500–7111 and PPX:500–7113 are configured for
use with the Siemens Industrial Automation, Inc. Local Line media on the
TIWAY I LAN, and have two 9-pin D-type female connectors at Ports 1
and 2.
Adapter PPX:500–7112 and PPX:500–7114 are configured for use with
RS-232/423 network transmission media, and have two 25-pin D-type
female connectors at Ports l and 2.
Ports 3 and 4. Port 3 on all models has a 25-pin D-type female connector.
Port 4 on all models has a 9-pin D-type female connector.
External I/O Connector. This is a 5-terminal, low voltage, screw-type
connector which can be used as an interface to an external signal or device.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Hardware Description
3-5
AC Power Connector. This is a 3-terminal screw-type connector.
!
WARNING
External Loopback
Connectors
The AC power connector cover should always be replaced after
field-wiring the Adapter AC power, and before power is energized.
Loopback connectors are provided for use during the USER diagnostics
described in Chapter 5. These connectors must be installed in order for your
Adapter to successfully complete the diagnostic tests.
Table 3-1 Factory-Supplied Loopback Connectors
Loopback Connectors Provided
Mounting Brackets
3-6
PPX#
9-Pin Connector
(P/N 2494055-0001)
25-Pin Connector
(P/N 2703834-0001)
PPX:500-7111, PPX:500-7113
1
1
PPX:500-7112, PPX:500-7114
1
3
The L-shaped mounting brackets shown in Figure 3-1 are used to mount
your Adapter in any one of several configurations described in Chapter 4.
These brackets are attached to your Adapter using the screws which are
supplied.
Hardware Description
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Chapter 4
Installing Your Unilink Adapter
This chapter provides the information necessary to properly install your
Unilink Adapter. Included are the following:
!
WARNING
•
the Adapter’s specifications and certifications.
•
hardware requirements.
•
hardware installation instructions.
•
Adapter dimensions.
•
required clearances for proper ventilation.
•
Adapter mounting configurations.
•
Local Line and RS-232-C cable installation guidelines.
•
suggested wire gauges.
Do not apply AC power to the Unilink Adapter until you have
completed all other installation procedures.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-1
4.1
Specifications and Certifications
•
Operating Temperature Range = 0 to 60° C (32 to 140° F)
•
Storage Temperature Range = –40 to 85° C (–40 to 185° F)
•
Humidity = 0 to 95% (non-condensing)
•
AC Line Voltage and Frequency (field-wired):
PPX:111, PPX:7112: 88 – 132 VRMS, 47 to 63 Hz
PPX:7113, PPX:7114: 140 – 264 VRMS, 47 to 63 Hz
4-2
•
Power dissipation = 20 vA maximum
•
Agency approvals = UL Listed; FM Class I Div. 2 Approved
•
Vibration = NAVMAT T 9492
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
4.2
Installation Procedure
The steps listed in this section should be followed when installing the
Unilink Adapter. Some needed information is found in other chapters, which
are referred to wherever necessary.
NOTE: You should read this entire section before attempting to install your
Unilink Adapter.
The procedures given here assume that you have an operating TIWAY I
Local Area Network. If you have questions regarding your TIWAY I
network, please refer to your SIMATIC TIWAY Systems Manual
(PPX:TIWAY–8101–x).
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-3
Installation Procedure (continued)
Adapter Installation – Overview. The steps listed in this paragraph
summarize the Unilink Adapter installation procedures. Details of each step
will be found in the paragraphs which follow this list.
1.
Make certain you have all necessary Unilink Adapter hardware
components for your Adapter model as listed in this section.
2.
Install the Adapter in a secure place which is convenient to your
TIWAY I network communications media and the attached device.
3.
If you have not done so already, install any network cables and
droplines necessary to connect Unilink Adapter Ports 1 through 4 to
your equipment.
4.
Wire in the connections to the External I/O Terminal, if this terminal is
to be used in your application.
5.
Install the PIM.
6.
Field wire the AC power line in accordance with local electrical codes.
7.
Replace the AC power terminal cover.
8.
Apply AC power to the Adapter.
9.
Execute USER Diagnostic Tests.
10. Execute RESET Diagnostic Tests.
11. Remove AC power from the Adapter.
12. Install the appropriate cables on Ports 1 through 4.
!
4-4
CAUTION
Before re-applying power to the Adapter and its attached
equipment, program the network computer(s) to operate the
Unilink Adapter in accordance with the instructions in your PIM
User Manual.
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Procedures and references for each of the above steps are given in the
paragraphs below.
Hardware Components
NOTE: If you are installing your own TIWAY I network cables, please refer
to your SIMATIC TIWAY Systems Manual (PPX:TIWAY–8101–x) for
additional information.
The following hardware is required to properly install the Unilink Adapter:
1.
The Unilink Adapter.
2.
L-shaped mounting brackets and the 10-32 x .375 bracket screws
(supplied with your Adapter).
3.
Local Line or RS-232-C network cables with the appropriate “D”-type
male connectors in place. Included with each Unilink Adapter
PPX:500–7111 and PPX:500–7113 are two 9-pin D-type male connectors
for use in constructing droplines from the TIWAY I Local Line.
Local Line
RS-232-C/423
PPX:500-7111*
PPX:500-7112+
PPX:500-7113*
PPX:500-7114+
*9-pin D-connectors included; +25-pin D-connectors not included
4.
AC power connector cover (supplied with your Adapter).
5.
Loopback connectors for USER Diagnostic Tests (supplied with your
adapter).
–
Two loopback connectors are included with PPX:500–7111 and
PPX:500–7113.
–
Four loopback connectors are included with PPX:500–7112 and
PPX:500–7114.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-5
Installation Procedure (continued)
6.
Two Siemens Industrial Automation, Inc. Tap Housings, Part No.
2702766–0001 (for Local Line installations only – supplied with your
Adapter).
7.
Mounting screws (user-supplied – .250 diameter).
8.
RS-232-C cable for use with modems (both cable and modems are
user-supplied).
9.
AC power wiring up to 14 A.W.G. (user-supplied and field-wired).
10. Dust caps – installed on all Adapter connectors.
!
CAUTION
Dust caps should remain in place unless the connectors they cover
are actually used. For example, if you do not have dual
transmission media, the dust cover for the unused network port
should NOT be removed.
Mounting the Adapter. For maximum environmental protection, and to
ensure extended trouble-free operation, Siemens Industrial Automation,
Inc. recommends that you mount your Adapter in a standard NEMA
enclosure.
If this is not possible, the Adapter should be installed in a secure, stable,
dry location free of corrosive elements, dirt, dust, ashes, and/or any other
debris, particularly debris which may be a by-product of a manufacturing
process.
In general, a minimum distance of three feet should be maintained between
the Unilink Adapter and any of the following:
4-6
1.
Power lines carrying
440 volts or greater.
6. Induction furnaces and heaters.
2.
Generators.
7. Rectifiers.
3.
Electric motors.
8. All sources of microwave
radiation.
4.
Transformers.
9. Teletypes.
5.
Electric welders.
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
•
Adapter Dimensions Without Brackets. Adapter outside
dimensions are given in Figure 4-1.
Figure 4-1 Unilink Adapter – Outside Dimensions
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-7
Installation Procedure (continued)
•
Adapter Dimensions – Brackets Installed. Center to center bolt
hole dimensions (with mounting brackets installed) are given in
Figure 4-2.
Figure 4-2 Adapter Dimensions – Brackets Installed
4-8
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
•
Required Clearances. Figure 4-3 illustrates the clearances necessary
for proper ventilation of the Adapter.
Figure 4-3 Required Clearances for Proper Ventilation
!
CAUTION
Clearances shown will ensure proper ventilation only if all vents on
your Adapter’s metal case are kept free of obstructions.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-9
Installation Procedure (continued)
Mounting Configurations. Siemens Industrial Automation, Inc.
recommends that you mount the Adapter in one of the configurations shown
in Figure 4-4 or Figure 4-5 below.
!
CAUTION
There are several other ways to mount the Unilink Adapter;
however, configurations other than those illustrated in this manual
could adversely affect Adapter operation.
Figure 4-4 Rack-Mount Configuration
4-10
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Figure 4-5 Surface-Mount Configurations
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-11
Installation Procedure (continued)
Cable Installation. Care should be taken when connecting cables to the
Adapter ports to avoid bending pins or otherwise damaging the “D”
connectors. After making certain all connectors are properly mated, secure
them with their mounting screws (see Figure 4-6).
Figure 4-6 Cable Installation
4-12
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Network Interface Ports 1 and 2. The Unilink Adapter Ports 1 and 2 (see
Figure 4-7) are the TIWAY I network interface ports. They support either
redundant Local Line transmission media (PPX:500-7111 and
PPX:500–7113), or redundant RS-232/423 media (PPX:500–7112 and
PPX:500–7114).
Figure 4-7 Unilink Adapter Ports 1 and 2 – Local Line
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-13
Installation Procedure (continued)
•
Local Line – Ports 1 and 2. The Local Line interface to TIWAY I is a
female 9-pin “D” connector. Pin assignments are shown in Table 4-1.
Table 4-1 Local Line Connector Pin Assignments
Pin
Name
Description
1
Reserved
2
Reserved
3
Shield
Cable shield and signal common
4
Reserved
5
Reserved
6
LLM+
Positive biased signal line
7
Reserved
8
Reserved
9
LLM–
Negative biased signal line
NOTE: The male ends of these two 9-pin connectors are included as part of
the hardware supplied with the Adapter for use in constructing the Local
Line drop cable. Suggested wire gauges are given in Table 4-7.
4-14
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
•
RS-232/423 – Ports 1 and 2. In Adapter models configured to support
dual RS–232/423 transmission media, both Ports 1 and 2 have 25-pin
D-type connectors installed. Figure 4-8 lists the Port 1 and 2 RS-232-C
signals and their respective connector pin numbers.
Figure 4-8 Unilink Adapter Ports 1 and 2 – RS-232/423
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-15
Installation Procedure (continued)
Table 4-2 RS-232-C D-Connector Pin Assignments/Ports 1 and 2
Interchange
Circuit
Connector
Pin No.
C.C.I.T.T.
AA
1
101
Protective ground
AB
7
102
Signal Ground/Common Return
BA
2
103
Transmitted Data
BB
3
104
Receive Data
CA
4
105
Request to Send
CB
5
106
Clear to Send
CC
6
107
Data Set Ready
CD
20
108/2
CF
8
109
Receive Line Signal Detector
DB
15
114
Transmitter Signal Element Timing
DD
17
115
Receiver Signal Element Timing
Description
Data Terminal Ready
NOTE: The male end of the 25-pin D-connector is not supplied with your
Adapter.
In the RS-232/423 configuration, the Unilink Adapter functions as Data
Terminal Equipment (DTE).
4-16
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Communications Ports 3 and 4. Ports 3 and 4 are independent serial ports
which are used by the Unilink Adapter to communicate with the attached
device.
Figure 4-9 Unilink Adapter Ports 3 and 4
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-17
Installation Procedure (continued)
•
Port 3. Port 3 is a general purpose serial port which implements a
subset of RS-232-C control, data, and timing signals using RS-423
drivers and receivers. It utilizes a 25-pin D-connector. Port 3 signals
and their respective connector pin numbers are given in Table 4-2.
Port 3 is wired as Data Terminal Equipment (DTE). Some applications may
require a port configured as Data Communications Equipment (DCE). Refer
to your PIM User’s Manual to determine the appropriate configuration.
For DCE configurations, use a null modem cable as shown in Figure 4-10.
Figure 4-10 Null Modem Cable
NOTE: The male end of the 25-pin D-connector is not supplied with the
Adapter.
In the DCE configuration, the Unilink Adapter will not provide synchronous
timing signals at this port.
4-18
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
•
Port 4. Port 4 is an application-specific serial communications port
which provides two media options in the same 9-pin connector. Please
consult your PIM User’s Manual for your specific application.
The transmission media options listed below are available at Port 4’s 9-pin
connector. Connector pin assignments are listed in Table 4-3.
1.
RS-422 Compatible
2.
RS-423
Table 4-3 9-Pin Connector Pin Assignments
Pin
Signal Name
Media
1
7
5
8
Transmit Data–
Transmit Data+
Receive Data–
Receive Data+
RS-422*
RS-422*
RS-422*
RS-422*
2
3
9
6
4
Transmit Data
Receive Data
Request to Send
Clear to Send
Signal to Ground
RS-423*
RS-423*
RS-423*
RS-423*
RS-423*
* Since the Unilink Adapter will typically be operating in a noisy industrial
environment line length not to exceed 50 feet is recommended.
NOTE: The male end of the 9-pin D-connector for Port 4 is not supplied
with your Adapter.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-19
Installation Procedure (continued)
External Input/Output. Use of the External Input/Output (I/O) terminal will
depend on your particular application. The PIM User Manual provides
additional information concerning the use of the External Input/Output
(1/O) terminal.
The following paragraphs provide additional information concerning
external 1/O connections.
As an option, the Unilink Adapter provides through the 5-terminal External
I/O Connector shown in Figure 4-11, one bit of input and one bit of output
for external use. Please refer to your PIM User Manual for additional
information.
Figure 4-11 External I/O Terminal
4-20
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
•
External I/O Connector Pinout. The connections to the External I/O
terminal should correspond to Figure 4-12. Suggested wire gauges are
given in Table 4-7.
NOTE: You must provide +20 to +30 VDC at pin 3 of the External I/O
Terminal if you use the external output. You do not have to apply power if
you use the input only.
Figure 4-12 Connections to the External I/O Terminal
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-21
Installation Procedure (continued)
•
The External Output. The Unilink Adapter optionally provides an
output signal in the range of 0 to 30 volts, at a current range of 0 to 0.5
amps.
Table 4-4 External Output Electrical Specifications
All values are for worst-case conditions unless otherwise noted.
User supply voltage range
20.0 to 30.0 VDC, Class 2
Maximum output current
500 mA
Surge current
2.0 A for 1 ms
OFF state leakage current
2.0 mA at 30 VDC
ON state voltage drop
2.0 V Max. at 500 mA
The output is internally protected against short circuits and reverse voltages.
!
CAUTION
4-22
The I/O terminal snaps out of the Adapter’s rear panel, enabling
you to connect wires without difficulty. Care should be taken when
re-inserting the I/O terminal.
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
•
!
CAUTION
The External Input. The Unilink Adapter’s remote input terminal
will accept incoming voltages as shown in Table 4-5.
Voltages above those listed in Table 4-5 should not be applied to the
External Input.
Table 4-5 External Input Electrical Specifications
All values are for worst-case conditions unless otherwise noted.
Input voltage range for guaranteed ON
conditions
20.0 to 40.0 VDC
20.0 to 36.0 VAC (RMS)
Input current range for guaranteed ON
conditions
5.0 to 15.0 mA
7.2 mA
Typical current input at 24 VDC and 25
degrees Celsius
–3.0 to 5.0 VDC
ON delay time range*
3.5 to 10 ms
OFF delay time range*
3.5 to 15 ms
*Measured from the time the input changes to the time the information is available to the
Unilink Adapter’s microprocessor.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-23
Installation Procedure (continued)
Attaching the AC Power Cable. With power OFF, field wire the AC power
cable to the Adapter.
!
WARNING
Always re-install the AC Power Connector Cover supplied with
your Adapter.
•
Voltage requirements (by model number) are listed in Table 4-6.
•
An illustration of the AC power terminal is given in Figure 4-13.
Table 4-6 Unilink Adapter Voltage Requirements
4-24
Model Number
Network Port
Input Voltage
PPX:500-7111
PPX:500-7112
PPX:500-7113
PPX:500-7114
Dual Local Line
Dual RS-232/423
Dual Local Line
Dual RS-232/423
120 VAC
120 VAC
240 VAC
240 VAC
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Figure 4-13 Unilink Adapter Power Connector
NOTE: Suggested wire gauges are given in Table 4-7.
PIM Handling Precautions. The PIM is a static-sensitive device, and should
be handled with care to prevent the accidental destruction of its ROM by
electrostatic discharge (ESD).
1.
Handle the PIM as little as possible.
2.
The PIM and persons handling the PIM should always be at the same
ground potential.
3.
The PIM should be stored and transported in its anti-static bag or in
anti-static material.
4.
Avoid touching the connectors which mate the PIM to the Unilink
Adapter. Static discharge might damage the PIM’s internal
components.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-25
Installation Procedure (continued)
Installing/Removing the PIM
!
WARNING
AC Power to the Adapter should be disconnected any time a PIM is
removed or replaced. The Adapter’s door should never be propped
open; it should be held open with your free hand.
Figure 4-14 PIM Location
4-26
•
Installation. When installing the PIM, slide it onto the Adapter
connector until it mates securely. Be careful to ensure correct vertical
alignment of the connectors. The PIM shield should ensure proper
horizontal alignment.
•
Removal. The PIM is removed by opening the Unilink Adapter’s
hinged door with one hand, then grasping its plastic case firmly
between thumb and forefinger of the other hand and pulling. Always
secure the Adapter door when finished.
Installing Your Unilink Adapter
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Initial Power-Up and Testing. Remove all cables attached to Ports 1 through
4 and proceed as follows:
1.
Apply AC power.
2.
Refer to Chapter 5 in this manual and execute USER diagnostics.
NOTE: If the Adapter fails the USER diagnostics, refer to the
Troubleshooting Section of Chapter 5 and proceed as suggested.
3.
If the Adapter successfully completes USER Diagnostics, refer to
Chapter 5 in this manual and execute RESET Diagnostics.
NOTE: If your Adapter fails its RESET diagnostics, refer to the
Troubleshooting Section of Chapter 5 in this manual, and proceed as
suggested.
4.
After successful completion of its diagnostic tests, your Unilink Adapter
is ready for operation. Refer to your PIM User Manual for operational
data relating to your specific application.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Installing Your Unilink Adapter
4-27
4.3
Connector Wire Gauges – Summary
The correct wire gauges for each connector and terminal on the Unilink
Adapter are summarized in Table 4-7.
Table 4-7 Connector Wire Gauges
Connector/Terminal
25-Pin D-Type Connector
9-Pin D-Type Connector
Screw-Terminal External I/O
Screw-Terminal AC Power
4-28
Installing Your Unilink Adapter
Wire Gauge
22 to 26 A.W.G.
22 to 26 A.W.G.
Up to 14 A.W.G.
Up to 14 A.W.G.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Chapter 5
Diagnostic Tests
The purpose of this chapter is to:
•
describe the functions of the Unilink Adapter’s switches and indicators.
•
provide complete diagnostic test procedures.
The diagnostic tests described in this chapter verify the proper operation of:
•
the diagnostics Read Only Memory (ROM).
•
the Adapter’s microprocessor, including its Random Access Memory
(RAM) and communications circuits.
•
the Adapter’s media boards, its power supply, watchdog timer, and
external loopback circuits.
•
the ROM of the Personality Interface Module (PIM).
A test failure generates an Error Code which defines the specific area in
which the failure occurred.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Diagnostic Tests
5-1
5.1
Status Display Indicators
The SIMATIC Unilink Adapter has six status display indicators (LEDs).
Only ADAPTER GOOD (LED number 1) is visible through the closed door.
You must open the door to see the remaining five.
Figure 5-1 Adapter LEDs
During normal operation of the Unilink Adapter, the various functions of
LEDs 2 through 6 are determined by the PIM. For a detailed discussion of
these functions, please refer to your PIM User Manual.
5-2
Diagnostic Test
TIWAY 1 Unilink Adapter Installation
and Operation Manual
When illuminated, the ADAPTER GOOD LED (see Figure 5-2) indicates
that the Unilink Adapter is functioning normally. This LED is also used as
an indicator during diagnostic testing and normal operation of your
Adapter. For information regarding LEDs two through six during tests,
please see Sections 5.7 and 5.8, which describe the LED functions during
USER and RESET Diagnostic Tests.
Figure 5-2 ADAPTER GOOD LED
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Diagnostic Tests
5-3
5.2
Diagnostic Tests: With or Without PIM
Unilink Adapter diagnostic tests will execute with or without the PIM
installed. However, when it is installed, the PIM executes tests in addition
to those conducted by the Adapter alone. Please refer to your PIM User
Manual for more information.
If your PIM is not installed, the Unilink Adapter will test its own
components. It will return Error Code 01000 indicating that the PIM is not
installed, even if the Adapter passes all other tests. Errors are displayed on
LEDs 2 through 6 (see Figure 5-3). For additional information, refer to
Sections 5.7 and 5.8.
Figure 5-3 LEDs 2 through 6
NOTE: One additional LED can be seen when the Unilink Adapter’s door is
open. This LED (not shown in this manual) is located below and to the right
of the RESET Switch. It is used only during Adapter manufacture and
testing.
5-4
Diagnostic Test
TIWAY 1 Unilink Adapter Installation
and Operation Manual
5.3
Reset Switch
The RESET Switch (see Figure 5-4) is accessible only when the Unilink
Adapter’s door is open.
!
WARNING
Pressing this switch causes a hardware reset and stops all system
operation. The Adapter enters a diagnostic test mode regardless of
system activity in progress at the time. The test mode entered is
either RESET Diagnostics or USER Diagnostics, depending on the
configuration of Position 10 of Dipswitch 2. For additional
information, please refer to Section 5.5 in this chapter, and to your
PIM User Manual.
Figure 5-4 The RESET Switch
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Diagnostic Tests
5-5
5.4
Dipswitches 1 and 2
Two ten-position dipswitches are accessible when the Unilink Adapter’s
door is opened (see Figure 5-5).
Figure 5-5 Dipswitches 1 and 2
The functions of each of the ten positions of Dipswitch 1, and the first nine
positions of Dipswitch 2, are described in your PIM User Manual.
Position 10 of Dipswitch 2 controls the diagnostic test mode entered at
powerup of the Unilink Adapter, or upon entering RESET (pressing the
RESET switch).
The UP configuration of this switch places the Adapter in the USER
diagnostic test mode at powerup or whenever the RESET Switch is pressed.
When this switch is in the DOWN configuration, it places the Adapter in the
RESET diagnostic test mode at powerup or whenever the RESET Switch is
pressed.
5-6
Diagnostic Test
TIWAY 1 Unilink Adapter Installation
and Operation Manual
5.5
Test Mode Selection
The two diagnostic test modes available to you are RESET and USER. The
mode the Adapter will enter depends on the configuration of Dipswitch 2,
Position 10 (see Table 5-1).
Figure 5-6 Dipswitch 2, Position 10
Table 5-1 Unilink Adapter Diagnostic Test Modes
Dipswitch 2
Position 10
Test Mode Entered
at power-up/RESET
PIM
UP
DOWN
USER Test
RESET Tests/Operations Mode
Not Required*
Not Required*
*Adapter Diagnostics will run with or without the PIM installed. The Operations Mode is entered
only when Position 10 of Dipswitch 2 is in the DOWN configuration.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Diagnostic Tests
5-7
5.6
LED Operation During Diagnostic Tests
In both test modes, the diagnostics software will switch ON LEDs 1 through
6 for visual inspection at the beginning of the tests. After 1 second, all LEDs
will then be switched OFF until the diagnostics finish, or until an error is
detected.
If the Unilink Adapter passes all Unilink Adapter tests and your PIM is
installed, the software in your PIM will run further tests.
For a description of USER Diagnostics, see Section 5.7.
For a description of RESET Diagnostics, see Section 5.8.
5-8
Diagnostic Test
TIWAY 1 Unilink Adapter Installation
and Operation Manual
5.7
User Diagnostic Tests
Prior to initiating USER Diagnostics, you must physically disconnect all
cables from Ports 1, 2, 3, and 4. Removing the cable from the External I/O
Terminal is not required.
NOTE: Failure to install loopback connectors, as discussed in the following
paragraphs, will cause the Adapter to fail its diagnostics.
The Unilink Adapter enters this test mode when
1.
dipswitch 2, Position 10, is in the UP configuration, and
2.
a RESET occurs.
NOTE: A RESET occurs when you power up the Unilink Adapter, and each
time you press the RESET Switch after power-up.
RS-232 Loopback Connector. Siemens Industrial Automation, Inc. RS-232
25-pin Loopback Connecter (Part Number 2703834–0001) should be
installed for external loopback tests of all RS-232/423 media ports. This
includes Ports 1 and 2 on Unilink Adapter PPX:500–7112 and
PPX:500–7114 and Port 3 on all models. These Loopback Connectors are
provided with your Adapter and a connector schematic diagram is given in
Appendix A.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Diagnostic Tests
5-9
User Diagnostic Tests (continued)
NOTE: Ports 1 and 2 of Unilink Adapter PPX:500–7111 and PPX:500–7113
(dual Local Line) do not require the installation of loopback connectors.
Mixed Media Loopback Connector. Port 4 (the mixed media channel)
must have a 9-pin Siemens Industrial Automation, Inc. Loopback Connector
(Part Number 2494055–0001) installed for satisfactory completion of the
USER diagnostic tests. This connector is provided with your Adapter and a
connector schematic diagram is given in Appendix A.
External I/O Terminal. You are not required to install a loopback connector
on the External I/O terminal.
NOTE: Executing the USER Diagnostics will turn OFF the External
Output.
To determine whether the external I/O circuits are tested for your
application, please refer to your PIM User Manual.
5-10
Diagnostic Test
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Test Execution. During USER diagnostics, all tests listed in Table 5-2 are
carried out, whether a PIM is installed or not (including external loopback
tests on Ports 1 through 4). If your PIM is installed, it will conduct
additional tests. Please refer to your PIM User’s Manual for details.
The ADAPTER GOOD LED will flash two times each second upon
completion of the USER Diagnostic Tests, regardless of whether an error
was found.
Diagnostics stop when the first error is encountered.
No Errors. When the Unilink Adapter successfully completes USER
Diagnostics, LEDs 2 through 6 will be extinguished, but the ADAPTER
GOOD LED will flash two times each second. This indicates that the
loopback connectors should now be removed and the cables re-installed on
Ports 1 through 4.
Error Indications. If an error is detected during USER diagnostics, the
ADAPTER GOOD LED will flash, and the Error Code will be displayed on
LEDs 2 through 6 inside the Adapter door. For a list of Error Codes, refer to
Table 5-2.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Diagnostic Tests
5-11
User Diagnostic Tests (continued)
Table 5-2 USER Diagnostic Tests and Error Codes
LED PATTERN
ERROR
L
2
3
4
5
6
No Errors
0
0
0
0
0
Diagnostics ROM Error
0
0
0
0
1
RAM Error
0
0
0
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
1
1
0
1
0
Communications Circuit Error
0
0
1
1
1
PIM Missing or PIM ROM Error
0
1
0
0
0
–5 V Power Supply Error
0
1
0
1
0
Watchdog Timer Error
0
1
0
1
1
External Loopback Errors
Port 1 External Loopback
Port 2 External Loopback
Port 3 External Loopback
Port 4 External Loopback
X
X
X
X
L = Loopback Connector Required
1 = LED Illuminated
If your PIM is not installed and the Adapter passes all its diagnostics, Error
Code 01000 (PIM Not Installed) will be returned.
Returning the Unilink Adapter to an Operational State. At the completion
of USER Diagnostics, the Unilink Adapter will enter a non-functional state
regardless of whether it has passed or failed.
5-12
Diagnostic Test
TIWAY 1 Unilink Adapter Installation
and Operation Manual
To return the Adapter to an operating state, follow the procedure outlined
below.
1.
Remove all loopback connectors installed on Ports 1, 2, 3, and 4.
2.
Install the cables you removed at the beginning of the USER diagnostic
test procedure.
3.
Reconfigure Position 10 of Dipswitch 2 by moving the switch lever to
DOWN.
NOTE: Install the PIM (if it is not already installed).
4.
Press the RESET Switch.
At this point, the Unilink Adapter will run the RESET diagnostic tests as
outlined in Paragraph 5.8. If no failure occurs and your PIM is installed, the
operation of your Adapter will be turned over to the software in your PIM’s
Read Only Memory.
NOTE: At the completion of the RESET diagnostics, the ADAPTER GOOD
LED flashes only if a failure occurs (see Section 5.8).
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Diagnostic Tests
5-13
5.8
Reset Diagnostic Tests
The Unilink Adapter enters this test mode when:
1.
Dipswitch 2, Position 10, is in the DOWN configuration, and
2.
a RESET occurs.
NOTE: RESET diagnostics will execute with or without cables installed on
Ports 1 through 4. A reset occurs when you power up the Unilink Adapter,
and each time you press the RESET Switch after powerup.
During RESET diagnostics, all tests listed in Table 5-3 are carried out.
Your PIM does not have to be installed for the RESET diagnostics to run.
However, if the PIM is installed, it will conduct tests in addition to those
conducted by the Adapter itself. Please refer to your PIM User’s Manual for
details. If an error is found, the PIM will instruct the Adapter to display the
appropriate Error Code on LEDs 2 through 6. For a list of the RESET
Diagnostic Error Codes, refer to Table 5-3.
5-14
Diagnostic Test
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Error Indications. If no error is detected, the ADAPTER GOOD LED will
illuminate at the completion of the diagnostics, and will remain illuminated.
All other LEDs will be extinguished.
If a failure is detected during RESET diagnostics, the ADAPTER GOOD
LED flashes two times each second, and an Error Code is displayed on
LEDs 2 through 6. For a list of these Error Codes, refer to Table 5-3.
The RESET diagnostics will run each time the RESET switch is pressed.
Table 5-3 RESET Diagnostic Tests and Error Codes
LED PATTERN
ERROR
2
3
4
5
6
No Errors
0
0
0
0
0
Diagnostics ROM Error
0
0
0
0
1
RAM Error
0
0
0
1
0
Communications Circuit Error
0
0
1
1
1
PIM Missing or PIM ROM Error
0
1
0
0
0
CPU Error
0
1
0
0
1
–5 V Power Supply Error
0
1
0
1
0
Watchdog Timer Error
0
1
0
1
1
1 = LED Illuminated
If your PIM is not installed and the Adapter passes all its diagnostics. Error
Code 01000 (PIM Not Installed) will be returned.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Diagnostic Tests
5-15
Reset Diagnostic Tests (continued)
Returning the Unilink Adapter to an Operational State. If no errors are
found during the RESET Diagnostics, the Unilink Adapter will, upon
completion of all tests, automatically pass control of its operation to the
PIM.
NOTE: Position 10 of Dipswitch 2 must be in the DOWN configuration for
normal Adapter operation, and the PIM must be installed.
5-16
Diagnostic Test
TIWAY 1 Unilink Adapter Installation
and Operation Manual
5.9
Troubleshooting
In the event of an Adapter malfunction, the following data should be of
value when performing diagnostic tests. If you require assistance, please
call your Siemens Industrial Automation, Inc. distributor or sales agent. If
you need assistance in locating your distributor or sales agent, call
800–964–4114. If technical assistance is needed, telephone 615–461–2522.
Table 5-4 Possible Adapter Malfunctions
Symptom
Possible Cause
Action
Error Codes
00011
00100
00101
00110
Error Code
01000
Loopback Connector not
installed; improperly installed;
or wrong connector installed.
Check all loopback connectors; adjust or repair as necessary.
Error Codes
00001
00010
00111
01001
01010
01011
Board failure.*
ADAPTER GOOD LED does not
illuminate.
No input power;
or
LED/Adapter
CPU malfunction.*
Unit failure or PIM not installed. Check your PIM; install if necessary.
Verify that user input power
falls within specifications and
is properly connected.
*Call Siemens Industrial Automation, Inc. for additional information.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Diagnostic Tests
5-17
Appendix A
Unilink Adapter Loopback Connectors
Schematic of the
RS-232/423
Loopback
Connector
Figure A-1 RS–232/423 Loopback Connector
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Unilink Adapter Loopback Connectors
A-1
Schematic of the
Mixed Media
Loopback
Connector
Figure A-2 Mixed Media Loopback Connector
A-2
Unilink Adapter Loopback Connectors
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Appendix B
Unilink Adapter Specifications
General
Specifications and
Certifications
•
Operating Temperature Range = 0 to 60 degrees C (32 to 140 degrees F)
•
Storage Temperature Range = –0 to 85 degrees C (–40 to 185 degrees F)
•
Humidity = 0 to 95% (non–condensing)
•
AC Line Voltage and Frequency (field–wired):
7111, 7112: 88 – 132 VRMS, 47 to 63 Hz
7113, 7114:140 – 264 VRMS, 47 to 63 Hz
•
Power dissipation = 20 VA maximum
•
Agency Approvals = UL Listed; FM Class I Div. 2 Approved
•
Vibration = NAVMAT T 9492
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Unilink Adapter Specifications
B-1
External I/O
Electrical
Specifications
Table B-1 External Output Electrical Specifications
All values are for worst-case conditions unless otherwise noted.
User supply voltage range
20.0 to 30.0 VDC, Class 2
Maximum output current
500 mA
Surge current
2.0 A for 1 msecond
OFF state leakage current
2.0 mA at 30 VDC
ON state voltage drop
2.0 V Max. at 500 mA
The output is internally protected against short circuits and reverse voltages.
B-2
Unilink Adapter Specifications
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Table B-2 External Input Electrical Specifications
All values are for worst-case conditions unless otherwise noted.
Input voltage range for guaranteed ON
conditions
20.0 to 40.0 VDC
20.0 to 36.0 VAC (RMS)
Input current range for guaranteed ON
conditions
5.0 to 15.0 mA
Typical current input at 24 VDC and 25
degrees Celsius
7.2 mA
Input voltage range for guaranteed OFF
conditions
–3.0 to 5.0 VDC
ON delay time range*
3.5 to 10 ms
OFF delay time range*
3.5 to 15 ms
*Measured from the time the input changes to the time the information is available to the
Unilink Adapter’s microprocessor.
TIWAY 1 Unilink Adapter Installation
and Operation Manual
Unilink Adapter Specifications
B-3
Customer Registration
We would like to know what you think about our user manuals so that we can serve you better.
How would you rate the quality of our manuals?
Excellent
Good
Fair
Poor
Accuracy
Organization
Clarity
Completeness
Overall design
Size
Index
Would you be interested in giving us more detailed comments about our manuals?
Yes! Please send me a questionnaire.
No. Thanks anyway.
Your Name:
Title:
Telephone Number:
(
)
Company Name:
Company Address:
Manual Name:
SIMATIC TIWAY 1 Unilink Adapter Installation and Operation
Manual Assembly Number: 2587871–0024
Order Number:
PPX: TIWAY–8106–2
Edition:
Date:
Fourth
04/94
FOLD
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL
FIRST CLASS
PERMIT NO.3
JOHNSON CITY, TN
POSTAGE WILL BE PAID BY ADDRESSEE
ATTN: Technical Communications M/S 3519
SIEMENS INDUSTRIAL AUTOMATION INC.
3000 BILL GARLAND RD
P O BOX 1255
JOHNSON CITY TN 37605–1255
FOLD