CrimeStopper CS-2002DPII Operating instructions

CS-2002DPII
With Data Port Technology
REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of an “On-Guard” Remote Alarm System with DP Technology by
Crimestopper Security Products Inc. This booklet contains the information necessary for installing, using, and
maintaining your alarm system. If any questions arise, contact your installation dealer or Crimestopper
Security Products Inc. at the Tech Support number below.
*IMPORTANT INFORMATION: Primary and Optional Features:
-PRIMARY: These are features that must be connected in order for the system to operate properly; i.e. the
Siren, +12V Power, Ground, Door pin, Flashing lights, LED/Valet Pod etc.
-OPTIONAL: These are features to be connected if desired or agreed upon by the installing dealer. These
features may also require additional parts and/or labor fees. Consult with your installer beforehand; i.e. Door
Locks, Starter disable, Hood/Trunk trigger, and Auxiliary Remote Outputs etc.
This installation book is designed for the installer or individual with an existing understanding of automotive
electrical systems, along with the ability to test and connect wires for proper operation. To ease installation,
we suggest that you READ THIS MANUAL before beginning your installation. This book is provided as a
GENERAL GUIDLINE and the information contained herein may differ from your vehicle.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
REV. D 1.2007
This device complies with FCC Rules part 15. Operation is subject to
the following two conditions: 1) This device may not cause interference,
and (2) this device must accept any interference that may be received,
including interference that may cause undesired operation. The
manufacturer is not responsible for any radio or TV interference caused
by unauthorized
modification to this equipment. Such modification
1
could void the user's authority to operate the equipment.
TABLE OF CONTENTS
Installation Cautions & Warnings…….……………………………….……………………………………………2
Control Module & Component Mounting……………...……………………..……………………….…………..3
Wiring……..……………………………………………………………………………………..……………….…….3-6
Parking Light Jumper Diagram……………………………………………….………………………….…..……..5
Power Door Lock Wiring……………………………………………………….………………………….…..……6-8
Transmitter Programming……………………………………………………………………………………………9
Option Programming…………………………………………….…….………………….…….………….….…10-12
Programmable Option Reset………………………………….…………………………….……………..………13
Custom Personal Override Code…………..………………….…………………………….……………………13
Remote Control Diagram…………...……………..…………………………………………………….………….14
Operating Instructions………………………..…………………………………….……………………..…….14-17
Car Jack Protection Features…………..……………………………………………...…………………….…17-18
LED / Valet POD & System Wiring Diagram…………………………………………..……………..………18-19
INSTALLATION CAUTIONS & WARNINGS
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR
BAGS, ABS BRAKES, ENGINE COMPUTERS, BATTERY etc.).
WE RECOMMEND the use of a VOLT/OHM METER to test and verify wiring circuits. Test lights or illuminated
probes can cause damage to on-board computer or engine management systems.
DO NOT exceed maximum output ratings.
WE RECOMMEND that the MAIN SYSTEM FUSE be REMOVED before jump starting, using a battery
charger, or changing the battery. A voltage surge or high boost condition could damage alarm circuits.
DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering
column, or any other moving parts in the vehicle.
2
CONTROL MODULE & COMPONENT MOUNTING
DO NOT Mount the control unit in the engine compartment or where the control unit or wiring harness
where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering
column! The alarm control module should be mounted in a concealed location. The Placement of the
module will affect the distance from which the remote transmitter can control the unit. The antenna wire
should be routed away from any metal if possible. Do not alter the length of the antenna wire or route it with
other wires. Do not ground the antenna wire. Fasten the module to a bracket or wire harness using the cable
ties provided. Under dash Mounting: If you are locating the control unit underdash, mount it as high as
possible, not easily located by an intruder. Driver’s Side Under dash mounting provides an easy location for
wiring most of the system’s connections, however this is a common location for an intruder to check for an
alarm after breaking into the vehicle.
SIREN: Mount the siren under the hood to an inner fender-well, wheel-well, or other body surface with the
open end facing downward. Run the red siren wire through the firewall using a rubber grommet. Ground the
black to the body metal near the siren or you can use one of the siren’s mounting screws for a ground.
Shock Sensor: Mount the included shock sensor with wire ties to an under dash wire harness or fasten with
screws to firewall or side paneling. Use the adjustment screw to set the sensitivity of the sensor. One screw
adjusts both
LED/Valet Pod: Mount the LED/Valet Button Pod push-button on dash or other accessible location. It is
REQUIRED for emergency disarm, programming features and entering valet mode.
WIRING
GREEN WIRE: (-) NEGATIVE DOOR TRIGGER
Identify the wire that reads ground when any door is open and 12 volts when all doors are closed. Some
vehicles may have isolated door triggers. In this case you may need to run additional wires from other doors
or go directly to the wire that triggers the vehicle’s interior dome light. Sometimes newer vehicles contain a
separate body control module (BCM) where the door trigger circuit can be located. One vehicle will not
require the use of BOTH door trigger wires.
VIOLET WIRE: (+) POSITIVE DOOR TRIGGER
Same as the GREEN wire above except this wire is used for vehicles that show a positive voltage (12 volts)
when the door is open and a ground when doors are closed as in many Ford, Lincoln, and Mercury vehicles.
3
WIRING
BLACK WIRE: SYSTEM CHASSIS GROUND
The Black wire MUST be connected the CHASSIS METAL of the vehicle. Scrape away any paint or debris
from the connection point and use a star washer to ensure a good connection. Keep the ground wire short.
YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS
Connect to an IGNITION wire (or fuse in the fuse box) that shows +12 Volts when the key in both “On” and
“Start” (WHEN CRANKING) positions.
GRAY WIRE: (-) NEGATIVE AUX REMOTE OUTPUT 1 (Optional, may require a relay)
Connect to the Negative trunk release circuit or to the activation circuit of an auxiliary module or device. If the
circuit requires +12V, then a relay is required. RELAY WIRING: Connect the Gray wire to terminal 85, connect
relay terminals 86 and 87 to +12V constant power. Connect terminal 30 of the relay to the +12V positive
device/circuit to be activated.
BLUE WIRE: (-) NEGATIVE HOOD/TRUNK TRIGGER (Optional)
Input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches that
read ground when open. If no existing switches are available, install new pin switches if desired. Note: DO
NOT mount new pin switches in water pathways.
BLACK/WHITE WIRE: (-) NEGATIVE DOME LIGHT ILLUMINATION OUTPUT (Optional, requires a relay)
This wire provides a (-) negative ground when the system is disarmed to activate a vehicles dome light circuit.
We recommend the use of a relay for this connection. Connect Black/White to terminal #85 of relay. Connect
terminal #86 to fused constant +12V. Connect terminal #87 to a +12V constant or ground source depending
on the type of dome light circuit in the vehicle. Connect Terminal #30 to the dome light circuit in the vehicle.
BROWN/WHITE WIRE: (-) NEGATIVE HORN PULSE / CHIRP OUTPUT (Optional, may require a relay)
Connect to the Negative Horn Trigger wire usually located near the steering column. If the vehicle horn circuit
requires +12V, then a relay is required.
ORANGE WIRE: (-) NEGATIVE ARMED OUTPUT (500mA Ground, Optional)
This wire becomes a constant Ground output when system is armed. This output can be used to activate
optional devices such as extra sensors, LED’s, window roll-up modules, voice modules etc.
WHITE/RED WIRE: (-) NEGATIVE AUX REMOTE OUTPUT 2 (Optional, may require a relay)
This wire connects the same way as Remote Output 1 see GRAY WIRE description above.
4
WIRING
BLUE/WHITE WIRE: (-) PASSENGER(S) DOOR UNLOCK OUTPUT (Optional, requires relay)
Connects to unlock circuit for passenger door(s) when using separate driver’s door unlock option. See
SEPARATE DRIVER’S DOOR UNLOCK WIRING on Page 8 for some configuration options.
BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.)
Connect to RED siren wire from the Siren in the engine compartment.
WHITE WIRE: PARKING LIGHT OUTPUT: +12V or (-) Negative Ground (Jumper Selectable)
Connect to switched +12V parking light wire at back of light switch. If this is not possible, connect directly to
one of the parking lights at the front of the vehicle. If your vehicle requires a (-) Negative Ground signal to
activate the parking lights, then you have to move the jumper located on the circuit board inside the unit. For
European vehicles with separate right and left circuits, use a dual relay or 2 diodes to separate the output
signal. The DEFAULT output is Positive. Carefully snap open the control module and see illustration below.
CS-2002DP IV Parking light output: The jumper plug inside the control
module determines the unit's (+) or (-) Parking Light output. Use the jumper
pin to select Positive or Negative Polarity Output. (*Default = Positive)
CS-2002DP IV MODULE
TOP VIEW OF P4 JUMPER
JUMPER
PLUG
JUMPER
PINS
NEGATIVE LIGHTS
+12V POSITIVE LIGHTS
(DEFAULT)
5
SIDE VIEW
WIRING
RED WIRE: +12V POWER INPUT (15 amp fuse)
Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the
vehicle battery positive terminal.
14 GA. BROWN WIRE: (On-board Starter Disable Relay)
Cut the 14GA. Brown wire in half. Connect the 2 female terminals to the Male terminals on the control
module. Cut the starter (Cranking only) wire on the vehicle. Connect the two brown wires to the 2 ends of the
Starter wires. See SYSTEM WIRING DIAGRAM on PAGE 19
2 PIN PLUG (BLUE): PROGRAM/OVERRIDE PUSH BUTTON (LED/Valet Pod)
Mount the LED/Valet Pod on the dash or other accessible location. This button is required when programming
options and when an emergency override is required.
2 PIN PLUG (WHITE): ALARM STATUS LED INDICATOR
Mount the LED/Valet Pod in a visible location of the dash or console.
4 PIN SENSOR PLUG/HARNESS (BLUE):
White Wire: Negative Trigger
Blue Wire: Negative Warn-away
Black Wire: Sensor Ground
Red Wire Sensor Power
SHOCK SENSOR: The sensor supplied with this system does not require any additional wiring. Simply
mount the sensor in a suitable location, plug it in, and adjust the sensitivity. There are 2 LED’s on the shock
sensor to assist you in adjusting sensitivity. The Green LED indicates the “Warn Away” level and the Red LED
indicates a full alarm shock sensor violation.
POWER DOOR LOCK WIRING
3 PIN DOOR LOCK PLUG (Optional):
GREEN: (-) Negative pulse for LOCK
RED: +12V Coil Power for using relays.
BLUE: (-) Negative pulse for UNLOCK
Hint: Determine the type of locking system the vehicle has
before connecting any wires. Incorrect connection could result
in damage to the alarm and/or the vehicle’s locking system.
6
POWER DOOR LOCK WIRING
NEGATIVE TRIGGER DOORLOCK WIRING
POSITIVE TRIGGER DOORLOCK WIRING
GREEN
GREEN
RED
RED
BLUE
BLUE
FUSED
+12V
+
85
86
87
87A 30
FACTORY
POWER
LOCKING
RELAYS
L
UL
85
86
87
87A 30
FACTORY
POWER
LOCKING
L
UL
RELAYS
REVERSE POLARITY DOOR LOCK WIRING
GREEN
GREEN
FUSED
+12V
+
RED
BLUE
85
86
87
87A 30
85
BLUE
85
86
L
UL
86
87
87A 30
87
87A 30
MASTER
SWITCH
+
FUSED
+12V
+
RED
CUT
CUT
7
85
86
87
87A 30
SEPARATE DRIVER’S DOOR UNLOCK WIRING
NEGATIVE TRIGGER DOOR LOCKS
BLUE/WHITE
GREEN
RED
BLUE
DRIVER'S
DOOR MOTOR
85
86
87
30 87A
L
L
UL
UL
FACTORY LOCK
RELAYS
+12V
+
FUSED
UNLOCK WIRE
CUT
WIRING FOR REVERSE POLARITY DOOR LOCKS
BLUE/WHITE
GREEN
RED
FUSED
+12V
BLUE
MASTER
SW ITCH
+
85
85
86
86
87
87A 30
87
30 87A
+
L
86
87
87A 30
CUT
UL
CUT
85
CUT
LOCK WIRE
UNLOCK WIRE
8
TRANSMITTER PROGRAMMING
NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes.
1.
2.
3.
4.
Turn key to the ON position and press program button 4 times.
After a short delay, the unit will chirp and flash the parking lights 4 times.
Press the Button #1 (Lock) on the remote you wish to program.
You should get 2 chirps and light flashes indicating the unit is waiting for the second code to learn.
Press button #1 of a second transmitter, the unit will chirp and flash 3 times. Press the lock button on a
3rd or 4th transmitter for up to 4 total. Note: The unit will not flash the lights when learning the 4th code.
Turn key off to exit programming mode.
IGN
OFF
WAIT FOR
4 FLASHES
PRESS 4X's
IGN
OFF
PANIC
FLASH 2, 3, or 4 X's
PRESS LOCK BUTTON
9
OPTION PROGRAMMING
1. Turn the Ignition ON and press the Override/Program button 5 times. After a slight delay, the system will chirp and
flash the lights 5 times.
2. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to
the options chart below. The siren and horn will chirp for each button press. DO NOT LOSE COUNT!!
3. When you get to the desired option number, quickly press the appropriate button on the remote control according to
the chart below. Button 1 gives a single light flash / chirp, Button 2 gives two light flashes / chirps, and Button 3
gives three light flashes / chirps.
4. Turn Ignition off. The system chirps and flashes the lights 3 times on exit. When you are finished customizing
options, check operation.
PROGRAMMING OPTIONS CHART
Option #
Option Description
BUTTON 1
LOCK
1.
Factory Horn Chirps / Pulses
Pulse with
trip only
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Passive Arming /
Passive Chirp Countdown
Passive Lock / Custom Override
Ignition controlled Locks
5/60 Sec. Door Open Warning
Active Re-Arm (30 Sec.)
Double Unlock Pulse
Silent Arm/Disarm
(Chirp Defeat w/button 1 or 2)
Parking Lights on with disarm
Disarm with trunk pop
N/A
Door Lock Pulse Time
Type of Carjack Protection
Carjack Enable/Disable
L/UL or Arm/Disarm w/IGN ON
Dataport Protocol 1-Way = OFA,
2-Way = SL
* = Default Setting
BUTTON 2
UNLOCK
Arm/Disarm
Chirps
& Pulse with trip
ON
*OFF*
ON
*ON*
5 Seconds
*ON*
OFF*
*OFF*
OFF
*60 Seconds*
OFF
ON
*OFF*
ON
*ON*
OFF
N/A
*0.7 Sec.*
OFF
*ON*
N/A
3 Sec.
*Active *
*Disabled *
*Lock/Unlock*
Active & Passive
Enable
Arm/Disarm
*2-Way*
1-Way
10
BUTTON 3
TRUNK
*Arm/Disarm/Warn Chirp
& Pulse with trip *
Passive Arm with
Chirp Countdown
Custom Override
Ignition Lock Only
Full-Time
OPTION PROGRAMMING
1. HORN CHIRPS / PULSES
This option controls the system’s Factory Vehicle Horn output. There are 3 selections: Button 1 (Lock) = Horn Pulse
only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disarm and Pulse when tripped. Button 3
(Trunk) = Horn Chirps for Arm, Disarm, and Pre-warning protection. All settings provide horn pulses when triggered.
2. PASSIVE ARMING / CHIRP COUNTDOWN
This option controls the Passive (Automatic) Arming feature. If ON, arming will occur 30 Seconds after the ignition is
turned off and the last door has been closed. The LED will begin flashing rapidly while counting down. If a door is
reopened, the system will wait for the door or zone to close before arming. The unit will flash the lights once. Doors
will lock if passive locking is selected. Factory default setting is OFF. If Passive Chirp countdown is selected, the
System will produce a siren chirp every 2 seconds as soon as the last door is closed until the system arms 30 seconds
later. Note: If you re-enter the vehicle you must turn ignition key ON and OFF for passive arming to reactivate.
3. PASSIVE LOCKS / CUSTOM OVERRRIDE (ALSO SEE CUSTOM OVERRIDE SECTION, PAGE 13)
This option controls whether the doors will lock when Passive Arming occurs. Note: May increase the risk of locking
keys in the vehicle. When selected ON the alarm will passively lock the doors when passive arming.
4. IGNITION-CONTROLLED LOCKS
This option controls whether the locks are controlled by Ignition. There are 3 selections: Button 1 (Lock) = Lock/Unlock
with vehicle Ignition. Button 2 (Unlock) = No ignition locks. Button 3 (Trunk) = Ignition lock only. Doors will not lock if
they are open to prevent locking the keys in.
5. DOOR OPEN WARNING (5 or 60 Seconds)
This setting changes the delay time in which the alarm system begins to monitor the Door circuit. This option can
prevent the alarm from giving warning chirps on vehicles with a delayed dome light.
6. ACTIVE RE-ARMING
Active Re-arming allows the system to re-arm itself 30 seconds after disarmed with the transmitter if a door has not
been opened. This is handy if the vehicle is accidentally disarmed (via the Transmitter in your pocket) without you
knowing it. Note: Active re-arm is reset by dome light illumination. If you are using dome light illumination, active rearm will not function.
11
OPTION PROGRAMMING
7. DOUBLE UNLOCK PULSE
With this feature enabled, the unit will send 2 unlock pulses when the #2 Unlock button is pressed. 2 pulses are required for
interfacing into some existing Factory Keyless Entry or Alarm systems on vehicles such as Nissan, VW, Toyota, and Lexus
vehicles.
8. SILENT ARMING /DISARMING (CHIRP DEFEAT)
With this feature, the system can be programmed to Arm and Disarm without the siren chirp using the regular Lock/Unlock
Buttons. Flashing parking lights will be the only Arm/Disarm confirmation.
9. PARKING LIGHTS ON WITH DISARM
Keeps parking lights on instead of 2 flashes when system is disarmed to assist in locating your vehicle in a crowded parking lot
or structure. Light will stay on for 30 Sec. or until Ignition is turned on.
10. DISARM WITH AUX. OUTPUT 1 (TRUNK POP)
Controls whether the system will or will not DISARM when the trunk pop or AUX. feature is used. When the feature is turned on
the unit will DISARM when opening trunk or using an auxiliary device controlled by the Gray output wire.
11. N/A, No option
12. DOOR LOCK/UNLOCK PULSE TIME
Controls the amount of time (0.75 sec. or 3 sec.) for the lock/unlock pulse. The 3 sec. setting may be required for 1980’/90’s
European Vehicles that require a long pulse to do Vacuum door lock systems.
13. ACTIVE, PASSIVE, or FULL-TIME CARJACK PROTECTION
This feature controls the type of Carjack protection the alarm will provide. There are 3 selections: Button 1 (Lock) = Active
protection. Button 2 (Unlock) = Active / Passive protection. Button 3 (Trunk) = Full-Time protection. Option number 14 must be
enabled to allow Carjack functions to operate. See Operation : Carjack.
14. CARJACK FEATURES
This option controls the unit’s Car Jack features. Enable or Disable Carjack (Turn ON or OFF) with this option.
15. ARM/DISARM WITH IGNITION ON
This option controls whether the unit will allow arming and disarm using the remote when the ignition is on (or vehicle is running).
This program option may need to be enabled when using an Add-on remote starter to allow the alarm to be armed or disarmed
after remote engine starting. Note that you cannot use this feature if you are also using the Full-time carjack protection. If you
add a remote start and the Ignition turns on, a Carjack trigger will be activated.
16. Data Port Protocol:
This option controls the Data Port Protocol for 1-Way (OFA modules) or 2-Way (SL modules). The default is set for 2-Way
Protocol. This option has no effect on conventional wiring of Bypass modules.
12
PROGRAMMABLE OPTION RESET
Follow the steps below to reset ALL OPTION VALUES ON PAGE 10 TO FACTORY DEFAULT SETTINGS.
1. Turn the Ignition ON and press the Override/Program button 5 times. The system will chirp and flash the
light 5 times.
2. Immediately press Button #3 (Trunk) on the remote.
3. The system will chirp and flash the light 3 times.
4. Turn off ignition and all programming options should be restored to * values. (See page 10)
CUSTOM PERSONAL OVERRIDE CODE
Custom override allows the user to set a specific number of button presses (2-15) required to perform an
emergency override/disarm of the alarm system. This increases the level of security of the system, but you
MUST MEMORIZE how many button presses you have changed your system to use or the unit will not disarm
in an emergency.
1.
2.
3.
4.
Enter programming mode. (See step #1 on page 10)
Press program button three times to go to option #3 “Passive Locks/Custom Override”.
Press the Button #3 (TRUNK) on the remote transmitter.
Press and release the program again the number of times you desire in order to perform emergency disarm
on this alarm system. Press the program button 2-15 times only. You need to wait for the siren to chirp the
same number of times you pressed the program button to confirm.
To test feature: Trip the alarm system, turn key ON, press the program/valet button 2-15 times as
programmed above then continue to HOLD DOWN valet button on the LAST PRESS for 5 seconds. Alarm
should disarm. If system does not disarm, then disarm with the remote transmitter and try again. If system
still does not disarm or you have forgotten your custom code, then you must use your remote control to disarm
the system
CAUTIONARY NOTE!
If you set up this feature and forget your special code, there is no way to disarm the system other than the
remote control.
TO CANCEL CUSTOM OVERRIDE CODE follow the Programmable Option Reset steps in the above section.
13
OPERATING INSTRUCTIONS
6 BUTTON REMOTE TRANSMITTER:
#2
UNLOCK
BANK #1 (Directly Press Buttons)
Button 1:
Button 2:
Button 3:
Button 4:
Button 5:
Arm
Disarm
Aux #1 (Trunk)
Panic
(Change to BANK #2)
#1
LOCK
BANK #2* (Press Bank #2 button FIRST,
then within 3 seconds Buttons 1-4)
#3
TRUNK
(AUX.)
Button 1: Silent Arm (No Chirp)
Button 2: Silent Disarm (No Chirp)
Button 3: Car Locator (5 light flashes, 1
siren chirp
Button 4: Aux #2
FLASHLIGHT
BANK #2
PANIC
#4
PANIC
* Remote LED Blinks 3 seconds for Bank #2.
ACTIVE ARMING
To arm the alarm and lock the doors, press the #1 (Lock Symbol) button on the transmitter. You will hear a single
siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these
optional features are installed. The red LED in the vehicle will start flashing after 5 seconds. After a short delay to
allow vehicle and electronics to stabilize the system will be completely armed.
ALARM TRIGGERING
If there is an intrusion into the vehicle or hard impact to the body will sound the alarm and flash the lights for 45
seconds. After 45 seconds the system will automatically shut off and re-arm to continue to protect the vehicle. If a
door is left open, the unit will cycle a second time and still continue to protect the other un-tampered zones.
DISARMING
Press the #2 (Unlock) button on the transmitter to disarm the alarm. You will hear 2 siren chirps and the lights will
flash twice. The LED stops flashing. Door will unlock and dome light will turn on if the options are installed. If you are
using the Optional Driver’s priority unlock, then the first press of the unlock button will unlock the driver’s door only and
the second press will unlock the passenger door or doors.
14
OPERATING INSTRUCTIONS
TRUNK/HATCH POP (REMOTE AUX. OUTPUT 1, OPTIONAL)
To pop the trunk (if optional feature is installed), press Button #3 (Trunk Symbol) on the transmitter for at least
1½ seconds. If the system is armed, pressing Button #3 may or may not trip the alarm system when opening
the trunk depending on programming option (10). See page 10.
REMOTE PANIC PROTECTION
To sound the alarm upon command (panic), press and hold the Button #4 (Panic) for at least 2 seconds until
the siren sounds. Press Button #2 (Unlock) to reset panic mode.
PRE-WARNING SHOCK PROTECTION & SENSOR ADJUSTMENT
If a low-level shock to the vehicle is detected, pre-warning protection will activate sounding 5 quick siren chirps
and 1 light flash. If a hard impact is detected the shock sensor should trip the alarm system. Once it is
mounted, adjust the sensor as needed by turning the adjustment screws clockwise to increase or counterclockwise to decrease the sensitivity. The sensor is also equipped with 2 small indicator lights to ease the
adjustment process. Green light = Pre-warning disturbance (6 siren chirps). Red light = A full alarm trip.
SELECTIVE SILENT ARM/DISARM THROUGH REMOTE CONTROL
This system can be armed and disarmed without siren chirps on an “as needed” basis. Press the Bank #2 on
the side of the remote and within 3 seconds use the lock/unlock buttons to arm/disarm without siren chirps.
PROGRAMMABLE SILENT ARM/DISARM MODE (CHIRP DEFEAT)
The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp. See
alarm programming option (#8) to enable or disable this feature. See page 10.
EMERGENCY OVERRIDE / DISARM
If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to
open the door with the key, which will activate the alarm. Turn the ignition on and press the override/program
button for about 3 seconds (until siren stops). The Alarm will disarm. If you continue to hold the button for
additional 3 seconds, the system will enter the Valet mode.
EMERGENCY DISARM WITH CUSTOM OVERRIDE
If you have programmed your system for Custom Override, follow the same steps above (Emergency
Override) while pressing the valet button 2-15 times as you have programmed. You must continue to hold the
button down on the last press for 5 seconds. The Alarm will disarm and enter the Valet mode, which allows
you to use the vehicle until you can repair/replace the remote transmitter or have the alarm system checked.
15
OPERATING INSTRUCTIONS
VALET MODE
To disable the Alarm system for vehicle service or otherwise, turn the ignition on and press the override/program button 4-5
seconds until the dash LED turns on solid and you hear (1) siren chirp. Repeat the process to exit VALET mode and the system
will chirp (2) times and the LED will turn off. Lock/Unlock and AUX features will still operate in when in VALET mode. When
performing an Emergency Override and you hold down the override button, the system is also placed into Valet mode. See
Emergency Override section on previous page.
PASSIVE ARMING / PASSIVE LOCK MODES / PASSIVE CHIRP COUNTDOWN
If programmed, passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been
closed. The LED will begin flashing rapidly while counting down. If a door is reopened, the system will wait for the door or zone
to close before arming. The unit will flash the lights once. Doors will lock if passive locking is selected. May qualify for insurance
discounts-check with your agent or proprietor. When the Unit is programmed for Passive Chirp Countdown, the siren will chirp
during passive countdown, as an audible warning that arming will occur. This siren will emit a chirp every 2 seconds as soon as
the last door is closed until the system arms 30 seconds later.
DOMESTIC SOFTWARE: ONE TIME PASSIVE ARMING
Passive Arming will work only one time after the ignition is turned off. When you disarm the alarm and re-enter vehicle, the alarm
system will not Passive Re-Arm.
EXPORT SOFTWARE: FULL TIME PASSIVE ARMING
The alarm system will always Passive Re-Arm after disarm. The ignition must be turned on to stop Passive Arming.
PRIOR INTRUSION ALERT
If the system was tripped in your absence, the dash LED will be flashing rapidly. When the system is disarmed you will hear 3
chirps (and 3 light flashes). Carefully inspect your vehicle to see if there is any damage or a theft has occurred.
DOME LIGHT ILLUMINATION (OPTIONAL)
This feature turns on the vehicles dome light upon disarm for 30 seconds or until the key is inserted and turned on. This will
provide illuminated entry to your vehicle at night or in dimly lit areas for added safety and security. Note that dome light
illumination will deactivate the active rearm feature if programmed for active rearm.
OPEN ZONE ALERT/BYPASS
If the system detects a faulty or open zone (Door left open) when the system is ACTIVELY ARMED, the siren will chirp 5 times
along with 5 light flashes. The faulty zone will be automatically bypassed.
IGNITION-CONTROLLED DOORLOCKS
The doors will automatically lock when the ignition is turned on and will unlock when the ignition is turned off. This feature can
be programmed on, off, or to lock the doors only. Doors will not lock if they are open to prevent locking the keys in.
16
OPERATING INSTRUCTIONS
ACTIVE RE-ARMING (FAIL-SAFE PROTECTION)
Active Re-arming means that the system will re-arm itself 30 seconds after disarmed with the transmitter if a door has not yet
been opened. This is handy if the vehicle is accidentally disarmed (via the transmitter in your pocket) without you knowing it.
This feature can also be turned off in programming option (6). Active rearm feature is disabled if you also have dome light
illumination installed.
2nd AUX. OUTPUT (REMOTE AUX. OUTPUT 2)
To activate the Second auxiliary output press the Bank#2 Button on the side of the remote first, then Press Button #4 (Panic) to
activate AUX. channel #2.
ARM/DISARM WITH IGNITION ON (PROGRAM OPTION #15)
This feature allows the system to be armed or disarmed while the ignition is in the ON position or vehicle is running. The feature
is disabled by default and should not be used under normal operating conditions. On an installation with an add-on remote start
module, this option can be enabled to allow the system to be armed or disarmed when the vehicle has been remote started
(Ignition will be ON). Note that you cannot use this feature if you are also using the Full-time carjack protection. If you add a
remote start and the Ignition turns on, a Carjack trigger will be activated.
CARJACK PROTECTION FEATURES
ACTIVE CARJACK
This feature provides Active Carjack protection and must be enabled before use through Alarm programming option (14) See
page 10. When the Ignition is on (vehicle is running), press button #4 (Panic). Parking lights will flash TWICE to confirm the
Carjack countdown sequence. LED begins to flash slowly. 90 Seconds later, the unit will begin a Carjack Cycle consisting of 20
seconds of pre-warning chirps turning into a full system activation with siren/flashing light pulses for 5 min. To reset Active
Carjack, IGNITION MUST BE ON, then press Button #2. Siren/Horn chirp, LED goes OFF, carjack is reset.
PASSIVE CARJACK
This feature provides Passive Carjack protection and must be enabled before use through Alarm programming options (13) &
(14). See page 10. We recommend this mode should only be used in serious situations. When the Ignition is on (vehicle is
running), and a door is opened and closed, the Carjack countdown sequence will be initiated (lights flash twice & LED begins to
flash). 90 Seconds later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre-warning chirps turning into a full
system activation with siren/flashing light pulses for 5 min. To reset Passive Carjack, Ignition must be ON, doors must be
closed, then press the override/program button (3) times. Siren chirps once, LED goes out, carjack is reset. NOTE: Active
carjack can still be used when the Passive Type carjack is activated.
17
CARJACK PROTECTION FEATURES
FULL-TIME CARJACK
ONLY USE THIS MODE WHEN THERE IS AN EXTREME TREAT OF A CARJACK WITH YOUR VEHICLE. Full-time Carjack
protection must be enabled before use through Alarm programming options (13) & (14). See page 10. EVERY TIME the Ignition
is turned ON or a door is opened and closed with the Ignition ON, a Carjack countdown sequence will be initiated. 90 Seconds
later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre-warning chirps turning into a full system activation with
siren/flashing light pulses for 5 min. You must reset the unit every time the IGNITION is turned on or a door is opened and
closed when the ignition is on. To reset Ignition must be ON, doors must be closed, then press override/program button (3)
times.
NOTE: When FULL TIME CARJACK is in effect, it must be reset every time the key is turned on, Door is opened, before
entering VALET mode, and before Programming options or transmitters! It is always in effect each time the Ignition is
turned on and/or a door is opened with Ignition on! If power becomes disconnected, then re-connected the Carjack
Full-time carjack trigger will be active. Press the override button 3 times with the Key on the doors closed to reset.
LED / VALET POD OPERATION & MOUNTING
LED / VALET BUTTON POD:
LED / VALET BUTTON POD MOUNTING:
LED POD
SYSTEM
LED
UNDER
Use
"L" Bracket
IN DASH
DASH
OR
VALET/PROGRAM
BUTTON
18
STARTER
BLACK(GROUND)
WHITE(WARNING)
BLUE (TRIGGER)
RED (+)
BROWN: (STARTER DISABLE)
START WIRE
CUT WIRE IN HALF FIRST,
THEN CUT STARTER WIRE
IN VEHICLE AND CONNECT
TWO HALVES AS SHOWN.
CUT
SHOCK SENSOR
OVERRIDE/
PROGRAM
BUTTON
LED
CS-2002DPII
(-) LOCK OUTPUT
GREEN
RED
(-) NEG. DOOR
PIN SWITCH
+12 VOLT FOR RELAYS
BLUE
RED
+12V POWER
FUSE
15A
+
(-) UNLOCK OUTPUT
-
PARKING
LIGHTS
BATTERY
(+) POSITIVE DOOR
PIN SWITCH
GREEN
WHITE
(-) DOOR TRIGGER
+12V 10A MAX or (-)
VIOLET
+
BROWN
(+) DOOR TRIGGER
IGN.
SW
SIREN
3A MAX
BLACK
CHASSIS GROUND
BLUE/WHITE
(-) PASSENGER
UNLOCK OUTPUT
FUSE
BOX
ACTIVATES ON
SECOND PRESS
OF UNLOCK BUTTON
YELLOW
(+) SWITCHED IGN "ON"
WHITE/RED
OPT.
RELAY
86
30
85
87a
87
GRAY
(-) REMOTE OUTPUT 2
(-) REMOTE OUTPUT 1
BLUE
(-) NEG.
PIN SWITCH
30
85
87a
87
NEG. ARMED OUTPUT
BLACK/WHITE
(-) DOME LIGHT OUTPUT
BROWN/WHITE
+
OR
85
87a
30 87
ORANGE
(-) HOOD/TRUNK TRIGGER
86
86
OPT.
RELAY
(-) HORN HONK
OUTPUT
DOME LIGHT
19
CONNECT TO
OPTIONAL DEVICES
SUCH AS WINDOW
ROLL-UP MODULE
DATA PORT DIAGRAM
Data bus Systems: Data Controlled door locks, Factory Security and many accessories
This unit includes DP Technology it will allow you to plug our modules which operate Data control Door locks,
accessories, and Bypass Factory security systems directly into the unit by via Data Port. The module cable
plugs directly to the Data port on the side of the unit. Please refer to Databus module manual for detail
instructions.
Option #16 controls the Data Port Protocol for 1-Way (OFA modules) or 2-Way (SL modules). The default is
set for 2-Way Protocol. This option has no effect on conventional wiring of Bypass modules.
BCM
Data wire
OFA
Bypass
Module
1
9
2
3
4
5
6
7
8
10 11 12 13 14 15 16
OBD connector
iDATA LINK CABLE
Data Port
Module Not Included
CS-2002DPII
www.crimestopper.com
Phone (800) 998-6880
FAX (805) 581-9500
ONLINE TECHNICAL SUPPORT
www.crimestopper.com
© 2007 Crimestopper Security Products
20