Barco MDRC-1119 User manual

MDRC-1119
MDRC-1119 TS
MDRC-1119 HB
MDRC-2120
User manual
Copyright notice
This document is copyrighted. All rights are reserved. Nor this
document, nor any part of it, may be reproduced or copied in any form
or by any means - graphical, electronic, or mechanical including
photocopying, taping or information storage and retrieval systems without written permission of Barco
© 2014 Barco N.V. All rights reserved.
2
Table of Contents
Table of Contents ....................................................................................... 3
Preface........................................................................................................ 5
Important notice.................................................................................... 5
Environmental information ................................................................... 6
Recommendations for using your display system............................. 11
Unpacking and handling tips .............................................................. 12
Preventing fire and injury ................................................................... 13
Cleaning the display ............................................................................ 14
Shipping/storing the display .............................................................. 14
Explanation of symbols ....................................................................... 16
Introduction .............................................................................................. 17
About the product ............................................................................... 17
Package Overview ............................................................................... 19
Installation ................................................................................................ 20
Product Overview ................................................................................ 20
Front View ....................................................................................... 20
Back View ....................................................................................... 21
Tilt ........................................................................................................ 22
Kensington Security Slot................................................................. 22
Start Your Installation .......................................................................... 22
Connecting the Display................................................................... 23
Adjusting the screen position ............................................................. 25
User Controls ............................................................................................ 26
Jog Dial Controls .................................................................................. 26
How to Use the OSD Menus ................................................................ 27
On-Screen Display Menus ................................................................... 28
Appendix .................................................................................................. 46
Troubleshooting ................................................................................... 46
Warning Signal .................................................................................... 47
Product Dimensions MDRC-1119/MDRC-1119 TS/MDRC-1119 HB ... 48
Technical specifications MDRC-1119 .................................................. 49
Technical specifications MDRC-1119 TS .............................................. 51
Technical specifications MDRC-1119 HB............................................. 54
Compatibility Modes MDRC -1119/MDRC-1119 TS/MDRC-1119 HB. 56
Product Dimensions MDRC-2120 ........................................................ 57
3
Technical specifications MDRC-2120 .................................................. 58
Compatibility Modes MDRC-2120 ....................................................... 60
Regulatory Compliance ....................................................................... 61
4
Preface
Important notice
Notice
Although every attempt has been made to achieve technical accuracy
in this document, we assume no responsibility for errors that may be
found. Our goal is to provide you with the most accurate and usable
documentation possible; if you discover errors, please let us know.
Barco software products are the property of Barco. They are distributed
under copyright by Barco N.V., for use only under the specific terms of
a software license agreement between Barco N.V. and the licensee.
No other use, duplication, or disclosure of a Barco software product, in
any form, is authorized.
The specifications of Barco products are subject to change without
notice.
Trademarks
All trademarks and registered trademarks are property of their
respective owners.
5
Environmental information
Disposal Information
The lamps inside the display contain mercury. Do not throw the display
in the trash. Dispose of it as required by local ordinances or regulations.
This equipment has required the extraction and use of natural
resources for its production. It may contain hazardous substances for
health and environment.
In order to avoid the dissemination of those substances in the
environment and to diminish the pressure on natural resources, we
encourage you to use the appropriate take-back systems.
Those systems will reuse or recycle most of the materials of your
end-of-life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those
systems.
If you need more information on the collection, reuse and recycling
systems, please contact your local or regional waste administrator.
You can also contact us for more information on the environmental
performances of our products.
6
China Energy Label
If there is a China Energy Label on your packaging or product, the
product meets the following energy requirements corresponding with
the energy efficiency level on the label.
按照中国<<能源效率标识管理办法>>
本显示器符合以下要求
本显示器符合以下要求
In accordance with The Regulation of
the Implementation on China Energy
Label
This monitor is
compliant with the
following requirements
This monitor is
compliant with the
following requirements
能源效率等级
1
2
> 1.05
> 0.85
< 0.5
< 1.0
GB 21520
GB 21520
Energy Efficiency Level
能源效率
Energy Efficiency (cd/W)
关闭状态能耗
Energy Consumption in off mode (W)
执行的能源效率国家标准编号
Code of National Standard applied
Safety Instructions
General Recommendations
• Read the safety and operating instructions before operating the
display.
• Retain safety and operating instructions for future reference.
• Adhere to all warnings on the display and in the operating
instructions manual.
• Follow all instructions for operation and use.
7
Electrical shock
Warning-
To prevent the risk of fire or shock hazards, do not expose
this product to rain or moisture
Warning-
Please do not open or disassemble the product as this may
cause electric shock.
Warning-
Do not modify this equipment without authorization of the
manufacturer.
Warning-
To avoid risk of electric shock, this equipment must only be
connected to a supply mains with protective earth.
Warning-
Make sure the user not to contact SIP/SOPs and the patient at
the same time.
Classification:
Electrical Shock Protection: Class I.
Disconnect Device: Connect / Remove power cord plug directly.
Degree of Protection Against Electric Shock: No applied part.
Degree of Protection Against Harmful Ingress of Water: Ordinary
equipment (IPX0).
Degree of Safety in the Presence of Flammable Anesthetic Mixture with
Air or with Oxygen or Nitrous Oxide: Not suitable for use in the
presence of a flammable anesthetic mixture with air or with oxygen or
nitrous oxide.
Mode of Operation: Continuous.
Intended use
This display is an AMLCD display designed for viewing medical X-ray
images. This unit should not be used near patients and should be kept
outside of 1.83 m perimeter and 2.29 m vertical.
8
The unit is not intended to be used in any life support system and
diagnosis.
Power connection
Power requirements: The display must be powered using a medical
approved 12VDC SELV power supply (MDRC-1119, MDRC-1119TS,
MDRC-1119HB) or a 24VDC SELV power supply (MDRC-2120).
The medical approved DC power supply must be powered by the AC
mains voltage.
The equipment should be installed near an easily accessible outlet.
Power cords
Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent,
18 AWG min., rated 300 V min., provided with a hospital-grade type
plug 5-15P configuration for 120V application, or 6-15P for 240V
application.
Do not overload wall outlets and extension cords as this may result in
fire or electric shock.
Mains lead protection (U.S.: Power cord): Power cords should be routed
so that they are not likely to be walked upon or pinched by items
placed upon or against them, paying particular attention to cords at
plugs and receptacles.
Use a power cord that matches the voltage of the power outlet, which
has been approved and complies with the safety standard of your
particular country.
Grounding Reliability
Grounding reliability can only be achieved when the equipment is
connected to an equivalent receptacle marked ‘Hospital Only’ or
‘Hospital Grade’ (located on product or power supply cord).
9
External equipment
External equipment intended for connection to signal input/output or
other connectors, shall comply with relevant UL/ EN/ IEC standard (e.g.
UL/EN/IEC 60950 for IT equipment and ANSI/AAMI ES60601-1/EN
60601-1 / IEC 60601 series for medical electrical equipment). In
addition, all such combinations – systems – shall comply with the
standard IEC 60601-1-1, Safety requirements for medical electrical
systems. Equipment not complying with ANSI/AAMI ES60601-1/EN /
IEC 60601-1 shall be kept outside the patient environment, as defined
in the standard.
Equipment not complying with IEC 60601 must be kept outside the
patient environment, as defined in the standard as at least 1.5 meters
from the patient or the patient support.
Any person who connects external equipment to signal input, signal
output, or other connectors has formed a system and is therefore
responsible for the system to comply with the requirements of IEC
60601-1-1. If in doubt, speak with a qualified technician.
In locations where 240V outlets are used, connect this display only on a
center-tapped, 240V, single-phase supply.
Water and moisture
Never expose the display to rain or moisture.
Never use the display near water - e.g. near a bathtub, washbasin,
swimming pool, kitchen sink, laundry tub or in a wet basement.
Ventilation
Do not cover or block the ventilation openings in the cover of the set.
When installing the display in a cupboard or another closed location,
heed the necessary space between the set and the sides of the
cupboard.
10
Installation
Place the display on a flat, solid and stable surface that can support the
weight of at least 3 displays. If you use an unstable cart or stand, the
display may fall, causing serious injury to a child or adult, and serious
damage to the equipment.
Recommendations for using your display system
1. Optimize the lifetime of your display
Enabling the Display Power Management System (DPMS) of your
display (in the display’s Settings menu) will optimize its lifetime by
automatically switching off the backlight when the display is not used
for a specified period of time. By default, DPMS is enabled on your
display, but it also needs to be activated on your workstation. To do
this, go to “Power Options Properties” in the “Control Panel”.
Barco recommends setting DPMS activation after 20 minutes of
non-usage.
2. Use a screen saver to avoid image retention
Prolonged operation of an LCD with the same content on the same
screen area may result in a form of image retention.
You can avoid or significantly reduce the occurrence of this
phenomenon by using a screen saver. You can activate a screen saver
in the “Display properties” window of your workstation.
Barco recommends setting screen saver activation after 5 minutes of
non-usage. A good screen saver displays moving content.
In case you are working with the same image or an application with
static image elements for several hours continuously (so that the
11
screen saver is not activated), change the image content regularly to
avoid image retention of the static elements.
3. Understand pixel technology
LCD displays use technology based on pixels. As a normal tolerance in
the manufacturing of the LCD, a limited number of these pixels may
remain either dark or permanently lit, without affecting the
performance of the product. To ensure optimal product quality, Barco
applies strict selection criteria for its LCD panels.
To learn more about LCD technology and missing pixels, consult the
dedicated white paper available at www.barco.com/healthcare.
4. Enhance user comfort
Every Barco multi-head display system is color matched with the
highest specification in the market.
Barco recommends keeping color-matched displays together.
Furthermore, it is important to use all displays of a multi-head
configuration at the same rate to preserve color matching throughout
the economic lifetime of the system.
5. Maximize Quality Assurance
The ‘MediCal QAWeb’ system offers online service for high-grade
Quality Assurance, providing maximum confidence and uptime.
Learn more and sign up for the free MediCal QAWeb Essential level at
www.barco.com/healthcare/qa
Unpacking and handling tips
The MDRC display is a precision instrument that requires proper care to
maintain product operation and adherence to specification. Unpack the
12
display and components carefully, then set up and handle the unit
properly to avoid damage to the LCD panel.
• Use both hands to grasp the display case when lifting it from
the shipping carton, but avoid touching the screen.
• Do not apply pressure to the screen or touch the screen with
bare fingers or objects. Pressure can affect image quality.
Cosmetics and oils on the skin are both detrimental to the
screen and difficult to remove.
• Allow the display to warm up to room temperature before
turning it on. Avoid sudden temperature changes in the
environment, as this may cause condensation, which damages
the display.
• Do not set up the display near strong light or heat sources.
• Do not block the vents on the back of the display or install the
display in a built-in enclosure. Blocked vents cause excessive
heat to build up inside the display, increasing risk of fire.
• When installing components, turn off your computer, but leave
it plugged into a grounded outlet.
• Do not remove the back cover or disassemble the display.
There are no user-serviceable parts inside.
Preventing fire and injury
• Replace the power supply or cables if damaged.
• Use only the power source indicated in this guide or listed on
the display.
• Do not plug the power supply into an overloaded AC outlet or
extension cord. Overloaded AC outlets and cords can result in
electric shock or fire.
• Do not drop or push objects into the display case. Internal
components contain high voltage.
13
• Unplug the power cord from the wall outlet during
thunderstorms.
• Do not place magnetic devices, such as motors, near the
display.
Cleaning the display
Observe the following guidelines to maintain display and LCD screen.
• Use a clean, lint-free, absorbent cotton cloth to clear off any
residual glue from removal of the protective film or to remove
surface dust. Apply light pressure to remove the dust.
• Dampen a clean cloth with a small amount of isopropyl alcohol
to remove glue or dust if the screen is still not clean. Do not
saturate the cloth; otherwise, alcohol may seep into the display
case and collect in the enclosure. Use a clean, dry cloth to
completely remove the alcohol residue.
• It is advised to clean the display on weekly basis.
• Do not use chemically treated dust cloths, acetone, toluene, or
harsh solvents on the display case or the screen. They can
damage the polarizer and the display case.
• Do not expose the display to water or excessive moisture. Do
not allow water or other stains to stand on the unit. Wipe
liquids off immediately to prevent damage to the display case
and the screen.
Shipping/storing the display
Keep the display in its shipping container until installation. Return the
display to its original container whenever you need to store the unit,
move it to another location, or return it for repair. The packaging
supplied by the manufacturer protects the display while it is in transit.
See environment specifications for more information.
14
Before returning the display to the container, do the following:
1 Swivel the display panel in landscape mode.
2 Push the panel down to the lowest position.
3 Use the stand lock to anchor the panel.
15
Explanation of symbols
DISPOSAL. Do not use household or municipal waste
collection services for disposal of electrical and electronic
equipment. EU countries require the use of separate
recycling collection services.
CAUTION. Read the accompanying text carefully for proper
operation and maintenance of the display system.
DIRECT CURRENT
ALTERNATING CURRENT
RELATIVE HUMIDITY
Storage & transport: 5%~ 90% (No condensation)
Operating: 8% ~ 80%
TEMPERATURE
Storage & transport: -20C° to 60C°
Operating: +15°C to +35°C
ISO 7000-1641. Follow operating instructions or consult
instructions for use.
16
Introduction
About the product
Thank you for choosing Barco.
The MDRC series are LCD displays with an active matrix, thin-film
transistor (TFT) liquid crystal display (LCD). These products also
demonstrate the following outstanding features:
MDRC-1119 / MDRC-1119 TS / MDRC-1119 HB
• Dual Analog and Digital signal.
• 19” diagonal Screen.
• 1280x1024 high resolution.
• Wide Viewing Angle Technology.
• 31.5 ~ 80 kHz horizontal scan.
• 56 ~ 75 Hz refresh rate.
• Auto Adjustment and Re-scaling function.
• High quality full screen re-scaling capability.
• Multilingual OSD user controls.
• VESA DPM power saving.
• Kensington lock capability
17
MDRC-2120
• Dual Analog and Digital signal.
• 20.1” diagonal Screen.
• 1600x1200 high resolution.
• Wide Viewing Angle Technology.
• 31.5 ~ 93.75 kHz horizontal scan.
• 59 ~ 61 Hz refresh rate.
• Auto Adjustment and Re-scaling function.
• High quality full screen re-scaling capability.
• Multilingual OSD user controls.
• VESA DPM power saving.
• Kensington lock capability
18
Package Overview
Power Adapter
USA Power Cord
VGA Signal Cable
EUR Power Cord
China Power Cord
DVI-D Cable
User’s Manual
19
Installation
Product Overview
Front View
20
Back View
MDRC-1119 / MDRC-1119 TS / MDRC-1119 HB
USB Ports
DC Power-In
VGA Input
DVI-D Input
MDRC-2120
DC Power-In
USB Ports
VGA Input
DVI-D Input
21
Tilt
Grasp the LCD Display with both hands and adjust the tilt as desired.
Kensington Security Slot
The Monitor can be secured to your desk or any other fixed object with
Kensington lock security products. Kensington lock is not included.
Kensington Security Slot
22
Start Your Installation
Connecting the Display
Use only the power adapter which are the forming part of each
medical device, the power cord, and the video cable shipped with this
display.
CAUTION: For MDRC-1119 / MDRC-1119 TS: The universal external 12V
DC/ 5.0A power adapter (100-240V~, 1.5A, 50-60Hz for power adapter
rating) is the BridgePower (BPM060S12F09). For MDRC-2120: The
universal external 24V DC/ 2.7A power adapter (100-240V~, 1.5A,
50-60Hz for power adapter rating) is the BridgePower
(BPM060S24F09). For MDRC-1119 HB: The universal external 12 V DC /
7.0A power adapter (100-240V~, 2.0A, 50-60Hz for power adapter
rating) is the BridgePower (JMW190KB1200F09).
To setup this display, please refer to the following figure and
procedures.
1.
Be sure all equipment is turned off.
2.
Connect the DC power cord to the power connector; plug one
end of the AC power cord into the power adapter, and the
other end into an electrical outlet. (1).
3.
For a PC with Analog output: Connect the VGA signal cable
from display VGA input connector to the 15-pin connector of
your host computer and tighten the screws. (2).
4.
For a PC with DVI digital output: Connect the DVI signal cable
to the connector of the display card in your computer, connect
the other side to the DVI-D input port of your display. Tighten
the screws (3).
5.
Turn on your computer, display and video source.
Note: To ensure the LCD Display will work well with your computer,
please configure the display mode of your graphics card to make it less
23
than or equal to the native resolution, and make sure the timing of the
display mode is compatible with the LCD screen. We have listed the
“Compatibility Modes” of this LCD screen in appendices for your
reference.
24
Adjusting the screen position
Vertical Height
Portrait/Landscape
Left to Right Pan
Front to Back Tilt
Remove Monitor
Stand may forcefully extend and cause injury
Lift Monitor to "Full UP" position in advance
Picking up the base or removing the monitor
25
User Controls
Jog Dial Controls


26
No./ Icon
Control
Function

- Power Switch
- Menu
1. Press the jog dial button for 1 sec
to power off to the LCD Display.
2. Swivel jog dial button for OSD
menu
Jog Dial button

LED
Power LED
1. Green indicates the display is
turned on.
2. Orange indicates the display is
in stand-by mode.
How to Use the OSD Menus
1.
Swivel the Jog dial button to pop up the ”on-screen menu”
and to scroll among the six Main Menus.
2.
Choose the adjustment items by pressing the jog dial button.
3.
Adjust the value of the adjustment items by swiveling the jog
dial button.
4.
After a period of inactivity *(based on a user setting), the OSD
menus will automatically disappear.
27
On-Screen Display Menus
Main Menu
28
Function
Description
Input Selection
Go to the ‘Input Selection Menu’ while the
jog-dial button is pressed.
Adjustments
Go to the ‘Adjustment Menu’ while the
jog-dial button is pressed.
Color
Go to the ‘Color Menu’ while the jog-dial
button is pressed.
Geometry*
Go to the ‘Geometry Menu’ while the
jog-dial button is pressed.
Settings
Go to the ‘Settings Menu’ while the
jog-dial button is pressed.
Information
Go to the ‘Information Menu’ while the
jog-dial button is pressed.
Exit
Close this menu.
29
Input selection Menu
30
Function
Description
DVI
Select the DVI input while the jog-dial
button is pressed.
VGA
Select the VGA input while the jog-dial
button is pressed.
Back
Go back to the ‘Main Menu’.
Exit
Close this menu.
Adjustments Menu
Function
Description
Brightness
To adjust the backlight luminance..
Contrast**
To adjust the image contrast (only applicable
if VGA is selected).
Sharpness**
Manual adjustment of the image sharpness
(only applicable if VGA is selected)
Gamma
Go to the ‘Gamma Menu’ while the jog-dial
button pressed.
Exit
Close this menu.
31
Adjustments -> Gamma menu
Function
32
Description
Native
Select the panel original gamma.
Gamma 1.8
Select the Dynamic Gamma 1.8.
Gamma 2.2
Select the Dynamic Gamma 2.2.
Dicom
Select the Dicom.
User
Select the user defined gamma which built
by QAWeb Agent tool.
Back
Go back to the ‘Adjustments Menu’
Exit
Close this menu.
Color Menu
Function
Description
Native
Select the panel original color temperature.
Clearbase
Set the image color temperature to Clearbase
Bluebase
Set the image color temperature to Bluebase
User
Go to the ‘User Menu’ while the jog-dial button
pressed.
Back
Go back to the ‘Adjustments Menu’.
33
Exit
Close this menu.
Color Menu -> User Menu
Function
34
Description
Red
Turn red gain value manually.
Green
Turn green gain value manually.
Blue
Turn blue gain value manually.
Back
Go back to the ‘Color Menu’.
Exit
Close the menu.
Geometry Menu**
Function
Description
Auto set
Adjust the image parameters to obtain a correctly
aligned image automatically while the jog-dial
button pressed.
clock
Adjust the internal clock frequency manually.
Increase this value to make the image wider,
decrease this value to make the image smaller.
Phase
Adjust the internal clock phase manually. If this
setting is not correct, the vertical bands with
alternate intensity will be visible.
35
36
Horizontal position
Adjust the image horizontal position manually.
Vertical position
Adjust the image vertical position manually.
Exit
Close this menu.
Setting Menu
Function
Description
OSD Setting
Go to the ‘OSD Settings menu’ while the
jog-dial button is pressed.
Factory Reset
Go to the ‘Factory Reset Menu’ while the
jog-dial button is pressed.
Language
Go to the ‘Language Menu’ while the jog-dial
button is pressed.
37
38
Power Save
Go to the ‘Power Save Menu’ while the
jog-dial button is pressed.
LED
Go to the ‘LED Menu’ while the jog-dial button
is pressed.
Back
Go back to the ‘Main Menu’.
Exit
Close this menu.
Settings Menu -> OSD Settings Menu
Function
Description
OSD Timeout
Set the OSD timeout value.
OSD Horizontal
Set the OSD horizontal alignment
OSD Vertical
Set the OSD vertical alignment
OSD Direction
Go to the ‘OSD Direction Menu’ while the jog-dial
button pressed.
Back
Go back to the ‘Settings Menu’.
Exit
Close the menu.
39
Settings Menu -> OSD Settings Menu -> OSD Direction
Function
40
Description
Landscape
Select OSD Landscape.
Portrait
Select OSD Portrait.
Back
Go back to the ‘OSD Settings Menu’.
Exit
Close the menu.
Settings Menu -> Factory Reset Menu
Function
Description
Yes
Execute the ‘Factory Reset’.
No
Abort the ‘Factory Reset’.
Back
Go back to the ‘Settings Menu’.
Exit
Close the menu.
41
Settings Menu -> Factory Reset Menu
Function
Description
English
Execute the ‘Factory Reset’.
Français
Select 'Français' as the OSD words while the
jog-dial button pressed.
Deutsch
Select 'Deutsch' as the OSD words while the
jog-dial button pressed.
Español
Select 'Español' as the OSD words while
thejog-dial button pressed.
Italiano
Select 'Italiano' as the OSD words while the
jog-dial button pressed.
Nederlands
Select 'Nederlands' as the OSD words while
thejog-dial button pressed.
日本語
Select '日本語' as the OSD words while the
jog-dial button pressed.
简体中文
Select '简体中文' as the OSD words while the
jog-dial button pressed.
繁體中文
Select '繁體中文' as the OSD words while the
jog-dial button pressed.
한국
Select '한국' as the OSD words while the jog-dial
button pressed.
42
Back
Go back to the ‘Settings Menu’.
Exit
Close the menu.
Settings Menu -> Power Save Menu
Function
Description
On
Enable the ‘Power Save’ function.
Off
Disable the ‘Power Save’ function.
Back
Go back to the ‘Settings Menu’.
Exit
Close the menu.
43
Settings Menu -> LED Menu
Function
44
Description
On
Enable the LED.
Off
Disable the LED.
Back
Go back to the ‘Settings Menu’.
Exit
Close the menu.
Information Menu
Function
Description
FW version
Firmware version
System hours
System run time
Backlight run time
Backlight run time
Back
Go back to the ‘Main Menu’.
Exit
Close the menu.
Notes 1:Symbol (*) means only active while VGA is selected.
Otherwise, it will be un-selectable with gray color, and the
subordinate items are blocked.
Note 2: Symbol (**) means only active while VGA is selected. Otherwise, it will be not selectable with gray color.
45
Appendix
Troubleshooting
If you are experiencing trouble with the LCD display, refer to the
following troubleshooting. If the problem persists, please contact your
local dealer or our service center.
Problem: No image appears on screen.
• Check that all the I/O and power connectors are correctly and
well connected as described in the “Installation” section.
• Make sure the pins of the connectors are not crooked or
broken.
Problem: Partial image or incorrectly displayed image.
• Check to see if the resolution of your computer is higher than
that of the LCD Display.
• Reconfigure the resolution of your computer to make it less
than or equal to the native resolution MDRC-1119, MDRC-1119
TS and MDRC-1119 HB (1280 x 1024) MDRC-2120(1600 x1200)
Problem: Image has vertical flickering line bars.
• Use “Clock” to make an adjustment.
• Check and reconfigure the display mode of the vertical refresh
rate of your graphics card to make it compatible with the LCD
Display.
46
Problem: Image is unstable and flickering
• Use “Phase” to make an adjustment.
Problem: Image is scrolling
• Check and make sure the VGA signal cable (or adapter) is well
connected.
• Check and reconfigure the display mode of the vertical refresh
rate of your graphics card to make it compatible with the LCD
Display.
Problem: Vague image (characters and graphics)
• Use “Clock” to make an adjustment. If this problem still exists,
use “Phase” to make an adjustment.
Warning Signal
Sometimes you may see warning messages for this LCD Display. This
means that the LCD Display cannot correctly receive the signal from the
computer graphics card.
No Signal
This message means that the LCD Display has been powered on but it
cannot receive any signal from the computer graphics card. Check all
the power switches, power cables, and VGA signal cable.
Out Of Range
This message means that the signal of the computer graphics card is
not compatible with the LCD Display. When the signal is not included in
the compatibility mode we have listed in the Appendices of this
manual, the LCD display will show this message.
47
Product Dimensions MDRC-1119/MDRC-1119
TS/MDRC-1119 HB
48
Technical specifications MDRC-1119
Product
MDRC-1119
Technology
TFT Color LCD (VA)
Native resolution
1280 x1024
Active screen diagonal
19" (483 mm)
Active screen area
376 x 301 mm
Pixel Pitch
0.294 x 0.294
Visual Characteristic
Maximum luminance
300 cd/m2
DICOM calibrated luminance
180 cd/m2
Image stabilization
BLOS (Backlight sensor)
Contrast ratio
1300:1
Aspect ratio
5:4
Viewing angle (CR>10)
178°/178°
Display LUT
10 bit
Response time (G-G)
8 ms
Display Functions
Gamma, Dicom
Colors
16.7 million
Connectivity and control
Video Input
DVI
VGA (DB15)
USB (1 upstream, 2 downstream)
49
OSD languages
English, French, German, Spanish, Italian, Dutch,
Simplified Chinese, Traditional Chinese, Korean.
Options
Protective Cover
Yes
Touch Screen
No
Landscape/Portrait
Yes
Certifications
EMC
EN 60601-1-2; FCC-B; ICES-001, VCCI, KC, CCC,
BSMI
Safety
CE EN 60601-1:2006+A11:2011; ANSI/AAMI
ES60601-1 (2005/(R)2012 + C1:2009/(R)2012
+ A2:2010/(R)2012), CAN/CSA-C22.2 No.
60601-1(2008), DEMKO-EN 60601-1:2006, CCC,
KC, PSE, BSMI
Mechanical characteristics
Display dimensions (W x H x D)
Landscape, w/o pedestal
418 x 346 x 70 mm
Display weight
With Stand :
8.75 kg
Without Stand : 5.65 kg
Display stand
Tilt, height & swivel
Mounting
VESA 100x100
WARNING: use suitable mounting apparatus to
avoid risk of injury.
Power requirements
System rating
Input: 12Vdc/5A
External DC Power Supply
Input: 100-240Vac (50Hz-60Hz), 1.5A
Output: 12Vdc/5A
For only use power supply BridgePower:
BPM060S12F09
Standby Power
<1W
50
Power consumption
50 Watts
Environmental
Operational temperature range
within specs
+15°C to +35°C
Storage & transport temperature
-20°C to +60°C
Operating humidity
8% - 80% (non-condensing)
Storage & transport humidity
5% - 90% (non-condensing)
Operating altitude
3048 m
Storage & transport altitude
5000 m
Operating pressure
70 kPa – 106 kPa
Storage & transport pressure
50 kPA – 106 kPA
Technical specifications MDRC-1119 TS
Product
MDRC-1119 TS
Technology
TFT Color LCD (VA)
Native resolution
1280 x1024
Active screen diagonal
19" (483 mm)
Active screen area
376 x 301 mm
Pixel Pitch
0.294 x 0.294
Visual Characteristic
Maximum luminance
300 cd/m2
DICOM calibrated luminance
180 cd/m2
Image stabilization
BLOS (Backlight sensor)
Contrast ratio
1300:1
51
Aspect ratio
5:4
Viewing angle (CR>10)
178°/178°
Display LUT
10 bit
Response time (G-G)
8 ms
Display Functions
Gamma, Dicom
Colors
16.7 million
Connectivity and control
Video Input
DVI
VGA (DB15)
USB (1 upstream, 2 downstream)
OSD languages
English, French, German, Spanish, Italian, Dutch,
Simplified Chinese, Traditional Chinese, Korean.
Options
Protective Cover
No
Touch Screen
Yes
Landscape/Portrait
Yes
Certifications
EMC
EN 60601-1-2; FCC-B; ICES-001, VCCI, KC, CCC,
BSMI
Safety
CE EN 60601-1:2006+A11:2011; ANSI/AAMI
ES60601-1 (2005/(R)2012 + C1:2009/(R)2012
+ A2:2010/(R)2012), CAN/CSA-C22.2 No.
60601-1(2008), DEMKO-EN 60601-1:2006, CCC,
KC, PSE, BSMI
Mechanical characteristics
Display dimensions (W x H x D)
Landscape, w/o pedestal
52
418 x 346 x 70 mm
Display weight
With Stand :
9.39 kg
Without Stand : 6.29 kg
Display stand
Tilt, height & swivel
Mounting
VESA 100x100
WARNING: use suitable mounting apparatus to
avoid risk of injury.
Power requirements
System rating
Input: 12Vdc/5A
External DC Power Supply
Input: 100-240Vac (50Hz-60Hz), 1.5A
Output: 12Vdc/5A
For only use power supply BridgePower:
BPM060S12F09
Standby Power
<1W
Power consumption
50 Watts
Environmental
Operational temperature range
within specs
+15°C to +35°C
Storage & transport temperature
-20°C to +60°C
Operating humidity
8% - 80% (non-condensing)
Storage & transport humidity
5% - 90% (non-condensing)
Operating altitude
3048 m
Storage & transport altitude
5000 m
Operating pressure
70 kPa – 106 kPa
Storage & transport pressure
50 kPA – 106 kPA
53
Technical specifications MDRC-1119 HB
Product
MDRC-1119 HB
Technology
TFT Color LCD (VA)
Native resolution
1280 x1024
Active screen diagonal
19" (483 mm)
Active screen area
376 x 301 mm
Pixel Pitch
0.294 x 0.294
Visual Characteristic
Maximum luminance
600 cd/m2
DICOM calibrated luminance
300 cd/m2
Image stabilization
BLOS (Backlight sensor)
Contrast ratio
2000:1
Aspect ratio
5:4
Viewing angle (CR>10)
178°/178°
Display LUT
10 bit
Response time (G-G)
8 ms
Display Functions
Gamma, Dicom
Colors
16.7 million
Connectivity and control
Video Input
DVI
VGA (DB15)
USB (1 upstream, 2 downstream)
OSD languages
54
English, French, German, Spanish, Italian, Dutch,
Simplified Chinese, Traditional Chinese, Korean.
Options
Protective Cover
No
Touch Screen
No
Landscape/Portrait
Yes
Certifications
EMC
EN 60601-1-2; FCC-B; ICES-001, VCCI, KC, CCC,
BSMI
Safety
CE EN 60601-1:2006+A11:2011; ANSI/AAMI
ES60601-1 (2005/(R)2012 + C1:2009/(R)2012
+ A2:2010/(R)2012), CAN/CSA-C22.2 No.
60601-1(2008), DEMKO-EN 60601-1:2006, CCC,
KC, PSE, BSMI
Mechanical characteristics
Display dimensions (W x H x D)
Landscape, w/o pedestal
418 x 346 x 70 mm
Display weight
With Stand :
7.61 kg
Without Stand : 4.42 kg
Display stand
Tilt, height & swivel
Mounting
VESA 100x100
WARNING: use suitable mounting apparatus to
avoid risk of injury.
Power requirements
System rating
Input: 12Vdc/7A
External DC Power Supply
Input: 100-240Vac (50Hz-60Hz), 2.0A
Output: 12Vdc/7A
For only use power supply BridgePower:
JMW190KB1200F09
Standby Power
<1W
Power consumption
47 Watts
55
Environmental
Operational temperature range
within specs
+15°C to +35°C
Storage & transport temperature
-20°C to +60°C
Operating humidity
8% - 80% (non-condensing)
Storage & transport humidity
5% - 90% (non-condensing)
Operating altitude
3048 m
Storage & transport altitude
5000 m
Operating pressure
70 kPa – 106 kPa
Storage & transport pressure
50 kPA – 106 kPA
Compatibility Modes MDRC -1119/MDRC-1119
TS/MDRC-1119 HB
Standard
Resolution
Vertical
Refresh
(Hz)
Horizontal
Scan
(KHz)
IBM VGA
IBM VGA
IBM VGA
640x350
640x480
720x400
70
60
70
31.5
31.5
31.5
VESA VGA
VESA VGA
VESA SVGA
VESA SVGA
VESA SVGA
VESA SVGA
640x480
640x480
800x600
800x600
800x600
800x600
72
75
56
60
72
75
37.9
37.5
35.1
37.9
48.1
46.9
VESA XGA
VESA XGA
VESA XGA
1024x768
1024x768
1024x768
60
70
75
48.4
56.5
60.0
56
VESA XGA
VESA XGA
1152x870
1152x864
60
75
54.36
68.1
VESA SXGA
VESA SXGA
1280x1024
1280x1024
60
75
63.96
79.95
Apple Mac II
Apple Mac
Apple Mac
640x480
832x624
1024x768
67
75
75
35.0
49.7
60.2
Product Dimensions MDRC-2120
57
Technical specifications MDRC-2120
Product
MDRC-2120
Technology
TFT Color LCD (IPS)
Native resolution
1600 x1200
Active screen diagonal
20.1" (510.54 mm)
Active screen area
432 x 331.5 mm
Pixel Pitch
0.255 x 0.255
Visual Characteristic
Maximum luminance
300 cd/m2
DICOM calibrated luminance
180 cd/m2
Image stabilization
BLOS (Backlight sensor)
Contrast ratio
800:1
Aspect ratio
4:3
Viewing angle (CR>10)
178°/178°
Display LUT
10 bit
Response time (G-G)
6 ms
Display Functions
Gamma, Dicom
Colors
16.7 million
Connectivity and control
Video Input
DVI
VGA (DB15)
USB (1 upstream, 2 downstream)
58
OSD languages
English, French, German, Spanish, Italian, Dutch,
Simplified Chinese, Traditional Chinese, Korean.
Options
Protective Cover
Yes
Touch Screen
No
Landscape/Portrait
Yes
Certifications
EMC
EN 60601-1-2; FCC-B; ICES-001, VCCI, KC, CCC,
BSMI
Safety
CE EN 60601-1:2006+A11:2011; ANSI/AAMI
ES60601-1 (2005/(R)2012 + C1:2009/(R)2012
+ A2:2010/(R)2012), CAN/CSA-C22.2 No.
60601-1(2008), DEMKO-EN 60601-1:2006, CCC,
KC, PSE, BSMI
Mechanical characteristics
Display dimensions (W x H x D)
Landscape, w/o pedestal
455 x 354 x 70 mm
Display weight
With Stand : 9.8 kg
Without Stand : 6.0 kg
Display stand
Tilt, height & swivel
Mounting
VESA 100 x 100 mm
WARNING: use suitable mounting apparatus to
avoid risk of injury.
Power requirements
System rating
Input: 24Vdc/2.7A
External DC Power Supply
Input: 100-240Vac (50Hz-60Hz), 1.5A
Output: 24Vdc/2.7A
For only use power supply BridgePower:
BPM060S24F09
Standby Power
<1W
59
Power consumption
55 Watts
Environmental
Operational temperature range
within specs
+15°C to +35°C
Storage & transport temperature
-20°C to +60°C
Operating humidity
8% - 80% (non-condensing)
Storage & transport humidity
5% - 90% (non-condensing)
Operating altitude
3000 m
Storage & transport altitude
5000 m
Operating pressure
70 kPa – 106 kPa
Storage & transport pressure
50 kPA – 106 kPA
Compatibility Modes MDRC-2120
Standard
Resolution
VGA
640x480
60
31.50
SVGA
800x600
60
37.68
XGA
1024x768
60
48.36
1152*870
60
54.36
SXGA
1280*1024
60
63.96
1MP2FH
1280*1024
60
62.50
1024*1280
59
77.78
UXGA
1600*1200
60
75.00
2MP2FH
1600*1200
59
72.81
1200*1600
59
95.84
60
Vertical Refresh (Hz)
Horizontal
Scan (KHz)
Regulatory Compliance
Canada, European Union, United States
This display has been tested and
found to comply with IEC/EN 60601-1
and IEC 60601-1-2 standards, and is
certified to meet medical standard
ANSI/AAMI ES60601-1 and CAN/CSA
C22.2 No 60601.1(C US Mark) which
are related to electrical shock, fire and mechanical hazards only as
shown on right UL mark on this page.
The medical display, in addition to meeting medical requirements, has
been tested and found to comply with the limits for Federal
Communications Commission (FCC) Class B computing devices in a
typically configured system since many medical offices are located in
residential areas. It is the system integrator’s responsibility to test and
ensure that the entire system complies with applicable
electromagnetic compatibility (EMC) laws.
Barco NV has made great efforts to support the medical device industry,
in particular, medical device manufacturers and medical device system
integrators. We offer state-of-the-art color displays that are compliant
with worldwide accepted medical device safety standards, and for the
European market, CE-marked displays based on compliance with
counsel directive 93/42/EEC—commonly referred to as the Medical
Device Directive (MDD). The following summarizes our qualification of
these displays as it relates to compliance with the MDD.
The European Medical Device Directive requires that the intended use
of the device be defined. The intended use of these displays is “to
display alphanumeric, graphic, and image data as inputted from any
type of medical device.” These displays do not provide a measurement
function in any way, and it is the device and systems manufacturer’s
responsibility to verify its function in the integrated device or system.
61
The display was classified as required by the MDD according to Annex
IX of the directive and the medical device (MEDDEV) guidance available
at the time of classification. Because the display uses electrical energy
and has no direct patient connections and—by itself—no medical utility,
the display is classified according to Rule 12 as an MDD Class I device,
component, or accessory. The MDD states that manufacturers of Class I
medical devices or accessories shall satisfy the requirements in regard
to design and manufacturing controls, that is, the applicable
assessment route to be used for CE-marking under the MDD, and it
shall carry the CE mark according to Annex XII of the directive, with no
notified body annotation.
In the opinion of Barco NV registration required to put this device into
commerce is the responsibility of the medical device/system
manufacturer, and Barco supports this requirement by providing a
European Commission (EC) declaration of conformity. If Barco supplies a
display to an end user, rather than a device manufacturer, it is the end
user’s responsibility to ensure continued compliance with the MDD of
the system in which the display is integrated.
The supplier will make available on request, circuit diagrams,
component part lists, etc.
For vigilance reporting as required under Article 10 of the MDD, Barco
NV will provide any information requested by competent authority to
support any reported incident investigation by such an authority.
EU Declaration of Conformity for Medical Application
A Declaration of Conformity has been filed for this product. For
additional copies of the Declaration of Conformity document, contact
Barco NV
The MDRC series digital flat-panel display meets the essential health
and safety requirements, is in conformity with, and the CE marking has
been applied according to the relevant EU Directives listed below, using
the relevant section of the following EU standards and other normative
documents;
62
EU EMC Directive 2004/108/EC
EU Electromagnetic Compatibility Directive
EN 60601-1-2 (2007)
Collateral standard
electromagnetic
Medical Electrical Equipment
compatibility requirements
EN 55011 (Class B)
Limits and methods of
measurements for radio
interference characteristics of
industrial, scientific, and medical
equipment
IEC 61000-3-2
Harmonic emissions
IEC 61000-3-3
Voltage fluctuations/flicker
emissions
IEC 61000-4-2
Electrostatic discharge
requirements for industrial
process measurement and control
equipment
IEC 61000-4-3
Radiated electromagnetic field
requirements for industrial
process measurement and control
equipment
IEC 61000-4-4
Electrically fast transients for
industrial process measurement
and control equipment
IEC 61000-4-5
Surge requirements
IEC 61000-4-11
Voltage variations/dips/interrupts
63
IEC 61000-4-6
Conducted immunity
IEC 61000-4-8
Magnetic field immunity
Conformance to the Medical
Device Directive 93/42/EEC
EN 60601-1 Medical Part 1
General requirements for safety
Electrical Equipment.
U.S. FCC Compliance Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
64
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technical for
help.
CAUTION: Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Other countries
Japan
VCCI level B
Korea
KC
PRC
CCC level B
Taiwan BSMI level B
65
66
67
B4100531-07
October 2014
Barco nv
President Kennedypark 35
8500 Kortrijk
Belgium
www.barco.com