Roberts Digital Radio with Dual Alarms CRD-29 User manual

Stream 83i Trouble shooting Guide
Important Note: For any unusual problem Factory reset your radio as explained on page85.
For Mac users, to make life easier, to listen to itunes on your radio, download ‘Eyeconnect¶
Symptoms
Cause/cure (#)
1a. Unable to find my wireless
network.
•
•
•
•
•
1b Unable to connect to the wired
network.
•
•
•
•
2a. Finds the network but after putting
in WEP/WPA key it simply fail to
connect.
•
•
•
•
•
•
•
•
•
•
Make sure the Ethernet cable (RJ-45) is not connected
between the radio and the Router/computer.
Make sure the radio is not out of range of wireless
router.
Make sure your wireless router is switched on and
working.
Move the aerial on radio and router for best signal.
Upright position is most favourable.
May be your network is configured not to broadcast
ESSID (i.e. hidden). Follow the section ‘connecting
your radio to your computer network’ on page 12-13 of
user manual.
Check the indicator lights incorporated into the RJ-45
connector. See page 12 of User Manual
Check the Ethernet cable for connection and damage.
Check if the power is connected to the modem and the
router (splitter).
Reboot your modem and router (splitter) by
disconnecting the power for two minutes then try the
radio for wired network (see flowchart page6).
Make sure you have the right key (look for correct
SSID and WEP/WPA key, may be printed on your
router base/back (may be called wireless key) or you
may have to go in router settings to find out), it is very
easy to make mistakes (especially if it’s a long
key).Make sure you are typing correct numbers and
letters – (confusing letters and numbers - 1, I, S, 5, 0,
O, T, 7, b, 6 etc.)
No spaces when entering key.
Remember WPA key is case sensitive.
Only 802.11b and 802.11g are supported. If your wifi
Router is 802.11n or g+ configure it to 802.11g, auto or
mixed mode depending on your router.
Router firewall may be an issue.
May be MAC filtering applied on the router (turn it off
or disable it).
May be a router WiFi problem (transmitting
capability).
See section 11 to 18 on page 12 of Instruction book.
Make sure the router is set for DHCP, if not, enable
DHCP.
See symptom 14 & 30.
1
2b. My Internet Radio is not
There can be a number of reasons for this:
connecting to my wireless network.
See symptom 30 as well.
•
The router / access point could be using a frequency not
supported by the Internet Radio. Please ensure that
your router / access point is configured to use mode: b,
g or b/g.
•
The problem could be due to encryption issues. You
could try connecting your Internet Radio to your
network in clear (encryption disabled (turned off)). If
the radio can connect to your network in clear, then it's
likely that the problem is somehow related to the
encryption settings on either the network or radio.
•
If you are using WEP encryption and the router is set in
'shared key' mode, try changing the authentication type
to 'open system'
•
If you are using WPA1-PSK encryption, then you need
to have all the network's keys configured for TKIP.
•
Interference from neighbouring wireless networks
could harm your Internet Radio's connection to your
network. Try and ensure that your router's / access
point's channel number to be at least two channels
away from any interfering sources.
•
Make sure you are using the latest firmware for your
router / access point. Note if you are using a Netgear
router, then you might need to configure the router to
an automatic setting.
Check that other devices on the network are able to
access the Internet. Check that there is no Firewall
blocking attempts to connect to external servers;
especially outbound connections on Port 5000
Uncheck (disable or switch off) – ‘SPI and Anti-DoS
firewall protection on the router’. You may find it
under the Security – Firewall – intrusion detection.
Switch off your radio by disconnecting the power; also
disconnect the power from router and modem, after 30
secs. Reconnect the power to the modem & router then
connect the power to the radio and try.
Also see symptom 14 &30.
Vigin Superhub please see following
Note:-- After selecting your SSID –
choose the option ‘Push button’.
•
Press the button shown above for 3
seconds. Then immediately press the
•
select button on your radio (i.e press
and release tuning control applies to
•
models using tuning control as select
button)).
•
3. It displays network not supported.
•
•
4. Showing low signal.
•
•
Only 802.11b and 802.11g are supported. If your wifi
Router is 802.11n or g+ configure it to 802.11g see
page 92 of user manual.
If using dual band router select the SSID for 11G
(Netgear)
Make sure the radio is not very far away from the
router. Try to bring radio closer to the router.
Make sure you are not logged on to your neighbour’s
open network.
2
•
5. Plays preset stations – ok, but when
I chooses ‘Radio Stations’ from the
menu it displays no network.
6. Radio crashes whilst loading
stations or sound cuts out while
playing.
7. Displaying ‘stream ended’ and stop
playing.
8. How to find the Mac address for
radio.
9. Sound stops and showing buffering.
Or Sound cut out while playing and
resume again.
If you experience rebuffering
problems, you may wish to consider
opening up the following TCP and
UDP ports on your router to see if
there is any improvement: 53, 80, 123,
554, 1755, 5000 and 7070 Also see
20.
10. Radio frozen, buttons don’t work.
11. When I select Register option it
says
Key:
Status: 404
•
Factory reset the radio, and or reset the router (you
must confirm how to reset your router without
configuring it again – most of the time switching the
power off/on clears the problem. Take every care not to
cause any problem with your system – if not sure
consult the technical department of the router provider).
Briefly disconnect the power to the radio.
It could be that due to network congestion, the loading
process is taking too long and the software for some
reason assumes that a reconnection is needed. Such
'congestion' can be anything from poor local network
conditions, through to poor bandwidth from the Internet
Service Provider, and possibly a slower than normal
response from ‘Wifiradio-frontier’ servers.
• The radio has reached the end of the stream it was
playing. This is normal behaviour for 'On Demand'
streams which terminate. It is occasionally observed
with live streams when they are busy or the connection
to them is poor.
• Press 'BACK' to enter the menu and either reselect the
same stream or select a new stream.
Follow the Path: See Flow Diagram on page 6
Main menu ńSystem settings ńNetworkńView settings
ńMAC Address. See section 4 page 89.
•
Router Buffer Size may be too small (e.g. Old Zyxel router).
This behaviour can be due to two things. Either, the
media-streaming service provided by the radio station is
unreliable - in that it has gaps in the stream (note: this
should be expected to happen occasionally) - or, your
wireless network has a problem such as interference (try
changing the channel). QOS (quality of service) in WAN
setting?
For more in-depth analysis of this problem see the
following link
http://forum.internet-radio.org.uk/guides/535-how-use-mtrtool-analyse-network-problems.html
Disconnect the radio from mains supply for 5 minutes then
reconnect...
It seems to be a problem with the Frontier server. The 404
or Not Found error messages are http generated standard
response. Means that the client was able to communicate
with the server but either the server could not find what
was requested, or it was configured not to fulfil the request
and not reveal the reason why. 404 errors should not be
confused with "server not found" or similar errors, in
which a connection to the destination server cannot be
made at all.
Factory Reset your radio and try it some other time.
3
12. Having problems with media
If UPnP does not work as expected, possible reasons may
player facility (including NAS drives). include:
UPnP functions blocked in firewall software
UPnP functions turned off by security software
UPnP functions ‘hi-jacked’ by other software
UPnP functions blocked in the router
Multi-cast packets blocked in the router
IP address of system blocked in firewall software.
Streaming software can enhance the playability of media
file.
You can try this free software http://www.orb.com/
Or http://tversity.com/download/ or
http://www.twonky.com/support/downloads.aspx most
people like this..
13a. Unable to use ‘Shared Media’
• Check that there are PCs sharing Media on the local
under ‘Music Player’.
network.
Make sure the port 2170 is open.
• If the PCs have a firewall installed check that either
a) the firewall is allowing all connections from the
local network or b) the firewall is allowing Netbios
traffic. Or turn off the firewall temporarily.
• If there is more than one computer on your local
network, ensure that any settings changes
(including booting up or turning off a computer)
have had at least 5 minutes to take effect.
• Check that other Windows machines are able to see
the server from which you are trying to share your
files.
• Check that 'File and Printer Sharing for Microsoft
Networks' is installed and bound to the local
network interface. Ensure that the 'Server' service
that provides file and print sharing support is
enabled and currently running. (Control Panel,
Administrative Tools, Services).
• Try rebooting PC and radio
OR (See page 33 Music Player)
Easier way to play media file on the radio is to use UPNP
Server. See operating Instructions to configure Windows
media player 11 as UPNP server. Or you can try this free
software http://www.orb.com/
13b. When playlist is selected it
It means your Library in Win Player is empty.
shows “Empty”.
Left Click on the Library button and select ‘Add to the
OR
Library’ – Just add all media folders to the library.
Tracks are not showing in the correct
Make sure all your files are in one location – My music
order. (You may be accessing
folder.
Windows Media Playlist or Albums -- Make sure under the ‘properties’ of this folder ‘Share this folder’ is
ticked i.e sharing this folder is enabled.
tracks may not be in correct order).
Or
Media sharing setting may be causing this problem.
Do the following
Open windows media player (applies to WMP 11).
1. Click the arrow below the Library tab, and then click
Media Sharing.
4
2. Click Settings. The Media Sharing - Default Settings
dialog box appears.
(If the Settings button does not appear on the Media Sharing dialog box, media sharing is
not turned on.)
3. Select the options (tick the check box) Music, Pictures
and Video under Media types.
4. Select All ratings under Star ratings: Select All ratings
under Parental ratings.
Or
Create a playlist or folder under 'my playlist' on
PC ('Document and settings'--'All users'--'shared
documents'--'shared music'---'my playlist').
On the radio select the options in the following order
'Shared Media' -- your PC--'Music' -- 'Folders' --'Shared
Music' -- 'My playlist' -- and then select what you have
created above.
14. I cannot get the radio to work with
my Wanadoo/Orange Livebox.
Or
Thomson TG585 Router. (press the
button in the front, it will give you 2
minutes to connect your radio.
On the back of the Orange Livebox, there are 2 buttons.
When setting the Livebox up to connect another unit to it,
be it a PC or Radio etc. then when you are ready to make
the WI-FI connection for the first time, it is necessary to
press the button numbered 1 (labelled wifi) to enable
"Pairing Mode". This in effect opens the Livebox to
receive incoming initiating signals for about 10 minutes.
During this period if you turn on the radio and select
Internet radio mode it should scan and find the Livebox,
select the Livebox and it will ask for the Key code, enter
the Key code (found on the base of the Livebox) and the
Radio should link up.
Put your Livebox into WiFi pairing mode
The Livebox uses something called MAC filtering, which
means that only computers or devices that you approve can
connect to the Livebox. To approve a computer or device,
press button 1 briefly on the back of the Livebox:
Remember to do this for all wifi equipments in your home.
15. Unable to play files (from
computer) which are downloaded
from Napster or itunes in WMA or
m4a format.
Not playing WMA Voice codec or the
WMA 10 Professional codec, DRM
protected file.
Most probably these files are protected. Radio will only
play unprotected files
File ext m4a (mpeg4 audio format) is not supported. Files
with ext.m4a have to be converted into mp3 or other
supported format.
Try
http://www.smartaudioconverter.com/?gclid=CPP4sd21g5
YCFQocQgodVnKeFA
5
16. Unable to play files (from
computer).
17. Can I use pause and fast forward
when listening to podcasts.
The Stream 83i supports WMA (the most common
variants), AAC, FLAC, REAL AUDIO and MP3 files.
The 83i does not support WMA Lossless format. This is in
common with most devices on the market which support
ordinary WMA files (WMA-Lossless support is almost
exclusively available on Microsoft products).
It does not support WMA Voice codec, the WMA 10
Professional codec or DRM protected files.
• If you have third-party software for firewall or antivirus protection, you may need to disable 'On-Access
Protection' in order for your radio to be able to
successfully play your music
No. Pause/ fast-forward only available in Music Player
(shared media, shared folders) mode.
18. Time reset it self to 0:00 or shows
incorrect time by one hour.
See section Clock and Alarms on page 70 -78.
19. Showing WIRELESS ERROR 10001
It means that no connection could be established
Are you using NETGEAR router? Do you have the
ACCESS CONTROL "ON" in the Wireless Station Access
List? If you have, you need to tell the router to allow your
radio's MAC address to have access. See 9 above.
RealAudio streams use port 7070 so if you encounter
buffering or other problems with RealAudio streams only,
check that port 7070 is open on your firewall.
20. BBC stations or Real Audio
streams keep rebuff ring.
Not applicable any more BBC has
stopped broadcasting in Real audio.
21. Worked for few days and now
showing no internet connection or
error.
22. BT Home Hub???
Reboot your radio by disconnecting mains electricity for 2
minutes.
Also check the leasing time in the router setting.
http://www.frequencycast.co.uk/guide.html
23. Time and date incorrect showing
00:00:00.
24. Having problem connecting to
BTHome hub using McAfee fire wall.
25. Radio switches off and reboots
itself after few minutes (using
BTHome hub and McAfee security BT NetProtect Plus). This problem
has been resolved by one of our
customer Daniel Chisholm. See right
In the event of power failure (or switching the radio off
from the mains), your radio will connect to the internet and
then set the clock automatically provided your internet is
working and auto update is set to internet (see page 72 73).
• 1: Turn off the firewall setting on the Hub management
system
2: Turn off the firewall on McAfee
3: Only then, switch on the radio and allow it to locate
the sources for both internet radio and file sharing
4: Restore the firewall settings
• This will allow the BT and McAfee systems to
configure and the
problem should stop
• To summarise (and help other customers who will
inevitably be confronted by this problem):
1: The problem only occurred with BT Home Hub
version 2.0
2: Something within the latest BT software has
6
in his own words.
triggered this problem, and the only way to clear it is
to:
* uninstall McAfee and replace with the Windows
Firewall
* Reboot the computer leaving the Stream 83i switched
on
* Reinstall McAfee ... then reboot the computer again
* everything should now be fine.
Try using static IP address (disable DHCP).
26. Having difficulties playing files
with Win Media Player 12. Plays only
one file.
27. Showing timed out when using
preset stations.
•
28. When I try to select Internet Radio
then Station List. It displays ‘Please
wait loading’ - ‘Network error Select to retry’. (DNS problem).
Try manual network configuration as explained on
page 16 – 18.
• Use the following Google free DNS address: Primary
DNS: 8.8.8.8
Secondary DNS: 8.8.4.4
• It could be due to a software in your computer causes
this problem.
• Cyberlink Power DVD 12 and certain Blu-Ray Player
software are known to cause this problem, but other
programs may cause similar issues.
• Switch off all other Networked devices and then try
Radio. Turn devices on one-by-one until Radio shuts
down by itself.
• See if software Update is available.
• Ensure the router is broadcasting in Wireless G mode
or 54Mbps
• Virgin Superhub instructions
Login to the Superhub (default IP is 192.168.0.1)
29. Radio crashes and switches off.
30. Virgin Superhub - Can see
Wireless but will not connect.
(suggested by our customer Nick
Manning)
•
Search the station using Location, Genre etc. Play the
station then preset it again.
•
Click Advanced Settings button
•
Click on Wireless Radio (at top of the list)
Then ensure that the 54Mbps mode is enabled. See
picture below.
7
DAB, USB, SD card Problems
Symptoms
1.
Radio cuts out. Try this link
http://www.ukdigitalradio.com/advice/
toptips/
Please note: If you live in a basement
flat, or your building is steel-framed or
reinforced concrete, or if the
topography of where you live means
you get poor FM or mobile phone
service, your DAB coverage may be
affected
2.
Tracks are not playing in
alphabetical order
Remedies
Make sure the aerial is fully extended. Reposition the
radio/aerial to get maximum signal strength (ref. To page 57Signal Error/ strength display).
• Make sure batteries are not flat (if using batteries). Try radio
on mains (using mains adaptor).
• Check the digital radio (DAB) coverage in your area using the
link – www.ukdigitalradio.com/coverage/search/default.asp
and your postcode.
The type of building and surroundings can seriously affect the
DAB reception. Sizeable concrete and metal work in the building
(e.g. Block of flats, shopping centre, near or under a bridge,
thermal insulation with aluminium foil) can considerably reduce
the signal strength.
• Playback order will be same as record order. First track
recorded will play first irrespective of file name and title.
•
Note: If you have had an unusual problem not listed and found the solution, please let us know for the benefit of other
users (if possible include the make and model of your router). The email address is a.g@robertsts.com thanks.
Disclaimer: Whilst every effort has been made to ensure the accuracy of the information supplied herein, Roberts Radio or RRTS cannot be
held responsible for any errors or omissions. Unless otherwise indicated, opinions expressed herein are those of the author of the page and do not
necessarily represent the corporate views of the Roberts Radio / RRTS
8