Delta CL180BN Instruction manual

(Model CL180BN)
PART NO. 912237 - 09-10-04
Copyright © 2004 Delta Machinery
To learn more about DELTA MACHINERY
ESPAÑOL: PÁGINA 17
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
INSTRUCTION MANUAL
Cordless Brad Nailer
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .2
SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . .7
SAFETY INSTRUCTIONS FOR CHARGER AND BATTERIES . . . . . . . .9
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
BATTERY CHARGING AND INSTALLATION . . . . . . . . . . . . . . . . . . . .10
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
SERVICE CENTER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . .back cover
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all warnings and operating instructions
before using any tool or equipment. When using tools or equipment, basic
safety precautions should always be followed to reduce the risk of personal
injury. Improper operation, maintenance or modification of tools or equipment
could result in serious injury and property damage. There are certain
applications for which tools and equipment are designed. Delta Machinery
strongly recommends that this product NOT be modified and/or used for any
application other than for which it was designed.
If you have any questions relative to its application DO NOT use the product
until you have written Delta Machinery and we have advised you.
Online contact form at www.deltamachinery.com
Postal Mail: Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
Information regarding the safe and proper operation of this tool is available from
the following sources:
Power Tool Institute
1300 Sumner Avenue, Cleveland, OH 44115-2851
www.powertoolinstitute.org
National Safety Council
1121 Spring Lake Drive, Itasca, IL 60143-3201
American National Standards Institute, 25 West 43rd Street, 4 floor, New York,
NY 10036 www.ansi.org ANSI 01.1Safety Requirements for Woodworking
Machines, and the U.S. Department of Labor regulations www.osha.gov
SAVE THESE INSTRUCTIONS!
2
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it
contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS.
The symbols below are used to help you recognize this information.
indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
indicates a potentially hazardous situation which, if not
avoided,could result in death or serious injury.
indicates a potentially hazardous situation which, if not
avoided,may result in minor or moderate injury.
used without the safety alert symbol indicates potentially
hazardous situation which, if not avoided, may result in
property damage.
3
GENERAL SAFETY RULES*
Read all instructions Failure to follow all
instructions listed below may result in electric shock, fire and/or
serious injury. The term "power tool" in all of the warnings listed
below refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric
shock
b) Avoid body contact with earthed or grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use reduces
the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal
injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
4
*The text used in the General Safety Rule section of this manual is
verbatim, as required, from the applicable UL60745 3rd edition standard.
GENERAL SAFETY RULES* continued
c) Avoid accidental starting. Ensure the switch is in the off-position
before plugging in. Carrying power tools with your finger on the switch
or plugging in power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance
with these instructions and in the manner intended for the
particular type of power tool, taking into account the working
conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous
situation.
5
*The text used in the General Safety Rule section of this manual is
verbatim, as required, from the applicable UL60745 3rd edition standard.
GENERAL SAFETY RULES* FOR BATTERY OPERATED TOOLS
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A
charger that is suitable for one type of battery pack may create a risk of
fire when used with another battery pack.
b) Use battery tools only with specifically designated battery packs.
Use of any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal
objects like paper clips, coins, keys, nails, screws, or other small
metal objects that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a
fire.
d) Under abusive conditions, liquid may be ejected from the battery,
avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
e) Ensure the switch is in the off position before inserting battery pack.
Inserting the battery pack into power tools that have the switch on invites
accidents.
6) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the
power tool is maintained.
SAVE THESE INSTRUCTIONS!
6
*The text used in the General Safety Rule section of this manual is
verbatim, as required, from the applicable UL60745 3rd edition standard.
ADDITIONAL SPECIFIC SAFETY RULES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Keep fingers AWAY from trigger when not driving fasteners to
avoid accidental firing. Never carry tool with finger on trigger. In
"contact actuation mode", tool will fire a fastener if tool is bumped.
Never point tool at yourself or others in work area. Serious injury or
death may occur if the tool is activated.
Disconnect tool from battery before doing tool maintenance, clearing a
jammed fastener, leaving work area, moving tool to another location, or
handing the tool to another person.
Never use tool if safety, trigger or springs are inoperable, missing or
damaged. Do not alter or remove safety, trigger, or springs. Make daily
inspections for free movement of trigger and safety mechanism.
Do not use tool without safety warning label. If label is missing,
damaged or unreadable, contact your Delta Service Center for a
replacement.
Always assume the tool contains fasteners. No horseplay. Respect
the tool as a working implement.
Do not load fasteners with trigger or safety depressed, or battery
inserted into tool, to prevent unintentional firing of a fastener.
Remove finger from trigger when not driving fasteners. Never carry
tool with finger on trigger.
Fire fasteners into work surface only: never into materials too hard to
penetrate.
Grip tool firmly to maintain control while allowing tool to recoil away
from work surface as fastener is driven.
Do not drive fasteners on top of other fasteners, or with the tool at too
steep an angle: the fasteners can ricochet causing personal injury.
Do not drive fasteners close to the edge of the workpiece. The
workpiece is likely to split allowing the fastener to fly free or ricochet
causing personal injury.
Be aware that this tool is always in an operating condition, because it
does not have to be plugged into an electrical outlet. Always set the
trigger switch to the locked “OFF” position when installing or removing the
battery pack or nails.
Some wood contains preservatives which can be toxic. Take extra care
to prevent inhalation and skin contact when working with these materials.
Request and follow any safety information available from your material
supplier.
SAVE THESE INSTRUCTIONS!
7
SYMBOL
V
........................
A
........................
Hz
........................
W
........................
kW
........................
F
........................
µF
........................
l
........................
g
........................
kg
........................
bar
........................
Pa
........................
h
........................
min
........................
s
........................
n0
........................
…/min or …min-1 .........
DEFINITION
volts
amperes
hertz
watts
kilowatts
farads
microfarads
litres
grams
kilograms
bars
pascals
hours
minutes
seconds
no-load speed
Revolutions or reciprocations per minute
or d.c. ................ direct current
or a.c. ................ alternating current
2
2N
3
3N
........................ two-phase alternating current
........................ two-phase alternating current with neutral
........................ three-phase alternating current
........................ three-phase alternating current with neutral
........................ rated current of the appropriate fuse-link in amperes
........................ time-lag miniature fuse-link where X is the symbol
for the time/current characteristic, as given in IEC 60127
........................ protective earth
IPXX
........................ class II tool
........................ IP symbol
SAVE THESE INSTRUCTIONS!
8
SAFETY INSTRUCTIONS FOR CHARGER
AND BATTERIES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
SAVE THESE INSTRUCTIONS. This manual contains important safety
and operating instructions for Delta Battery Charger.
Before using a battery charger, read all instructions and cautionary
markings on (1) battery charger, (2) battery pack, and (3) product using
battery.
To reduce risk of injury, a Delta charger should only be
used to charge a Delta battery pack. Other types of batteries may burst
causing personal injury and damage. Do not charge a Delta battery pack
with any other charger.
Do not expose charger to rain, snow or frost.
Do not abuse cord. Never carry charger by cord or yank it to
disconnect from receptacle. Pull by plug rather than cord when
disconnecting charger. Have damaged or worn power cord and strain
reliever replaced immediately. DO NOT ATTEMPT TO REPAIR POWER
CORD.
Make sure cord is located so that it will not be stepped on, tripped
over, or otherwise subjected to damage or stress.
Do not use an extension cord unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock.
If an extension cord must be used, make sure:
A. That the pins on plug of extension cord are the same number, size
and shape as those of plug on charger.
B. That the extension cord is properly wired and in good electrical
condition.
C. Wire Size of cord is at least as specified in following chart:
LENGTH OF CORD IN FEET
25
50
100
150
AWG SIZE OF CORD
18
18
18
16
D. If an extension cord is to be used outdoors it must be marked with
the suffix W-A or W following the cord type designation. For example –
SJTW-A to indicate it is acceptable for outdoor use.
Do not operate charger with damaged cord or plug – have them replaced
immediately, to avoid a hazard. DO NOT ATTEMPT TO REPAIR POWER
CORD.
Do not operate charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way; take it to a qualified serviceman.
Do not disassemble charger or battery pack. Take it to a qualified
serviceman when service or repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
Unplug charger from outlet before attempting any maintenance or
cleaning – to reduce risk of electric shock.
Charge the battery pack in a well ventilated place, do not cover the
charger and battery pack with a cloth, etc., while charging.
Do not store the charger or battery pack in locations where the
temperature may reach or exceed 122°F (50°C) (such as a metal tool
shed, or a car in the summer), which can lead to deterioration of the
storage battery.
9
14. Do not charge battery pack when the temperature is BELOW 40°F
(4.4°C) or ABOVE 104°F(40°C). This is very important for proper
operation.
15. Do not incinerate battery pack. It can explode in a fire.
16. Do not charge battery in damp or wet locations.
17. Do not attempt to charge any other cordless tool or battery pack with
the Delta charger.
18. Do not short across the terminals of the battery pack: EXTREMELY
HIGH TEMPERATURES COULD CAUSE PERSONAL INJURY OR FIRE.
19. Double insulated tools are equipped with a polarized plug (one
blade is wider than the other). This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any way. Double
Insulation
eliminates the need for the three wire grounded power
cord and grounded power supply system.
20. Dispose of expended batteries properly. The
Delta Battery Packs contains rechargeable, nickelcadmium batteries. These batteries must be
recycled or disposed of properly. Drop off
expended battery packs at your local replacement
battery retailer, your local recycling center, or at a
Delta Service Center (see list on back page of this
manual). Applicable fees for the collection and
RBRC™ is a Trademark of
recycling of these batteries (in the United States),
the Rechargeable Battery
Recycling Corporation.
have been paid to the RBRC™. For further
information, call: 1-800-8-BATTERY.
SAVE THESE INSTRUCTIONS!
FUNCTIONAL DESCRIPTION
FOREWORD
Delta Model CL180BN Cordless Brad Nailer is a heavy duty pneumatic brad
nailer. It is designed to install 18 ga. brad nails of various lengths (from 5/8" to
11/4" long).
CARTON CONTENTS
SOLD ONLY IN COMBO KIT CL180WWK that includes;
1) CL180 - Drill
2) CL180C - Charger
3) CL180CS - Circular Saw
4) CL180JS - Jig Saw
5) CL180PS - Pad Sander
6) CL180BN - Brad Nailer
7) CL180FL - Flashlight
8) CL180B - Battery - 2
9) Case
BATTERY CHARGING AND INSTALLATION
CHARGING THE BATTERY
Before using your cordless tool for the first time, fully charge the battery
pack. If the battery pack is installed in the tool, remove it by following
instructions under INSTALLING OR REMOVING BATTERY PACK.
10
As a battery pack approaches the discharged state, you will notice a sharp
drop in tool performance. When the tool is unable to perform the task at
hand, it is time to recharge the battery pack. Recharging the battery pack
before this condition is reached will reduce the total work life of the pack.
Discharging the pack beyond this point can damage the pack.
NOTE: Battery temperature will increase during and shortly after
use. Batteries may not accept a full charge if they are charged
immediately after use. Allow the battery pack to cool to room
temperature before charging for best results.
The battery charger must rest on the four pads provided on the
bottom of the case. Vent slots in top and bottom of charger must not be
obstructed. Do not charge battery when temperature is BELOW 40°F (4.4°C) or
ABOVE 104°F (40°C).
NORMAL CHARGING AND DIAGNOSTICS
Make sure power circuit voltage is the same as that shown on the charger
specification plate. Connect charger to power source. The orange light (A) Fig.
2, should light up. This indicates the charger is ready to begin charging.
Position battery pack on charger, align rails (D) Fig. 2 and Fig. 3, on battery
charger with four tabs (C) Fig. 3 on battery pack. Slide battery forward onto
charger until it stops.
The red light (B) Fig. 2, should begin to glow continuously, indicating that the
battery pack is receiving a “Fast Charge” (if the red light does not glow
continuously, and the green light (C) Fig. 2, begins to glow: remove battery and
re-insert when battery temperature is between 40°F (4.4°C) and 104°F (40°C).
After approximately one hour, the “Fast Charge” indicator light (red) should go
out indicating that the battery pack is fully charged and that the charger is now
in a “Trickle Charge” mode (green light). The battery pack can be left on
“Trickle Charge” until you are ready to use it.
B
C
A
D
C
D
D
D
Fig. 3
Fig. 2
Depending on room temperature, line voltage, and existing charge level, initial
battery charging may take longer than one hour.
Disconnect charger from power source when not in use.
Special Charge Modes: If all lights go out after the battery is inserted, the
charger has entered pre-charge mode. In approximately 5-10 minutes, the
orange and red lights should turn on indicating that fast charge has been
initiated. If all lights remain off after 15 minutes, remove the battery. The
orange light should glow. Reinsert the battery. If the orange light goes out
when the battery is inserted and all lights remain off for 15 minutes, battery
should be replaced.
After inserting battery, if the orange light is on while the red and green lights
remain off, remove battery and re-insert. If the orange light is on while the red
and green lights remain off, battery should be replaced.
11
INSTALLING OR REMOVING BATTERY PACK
Always set the trigger
switch to the locked OFF position
when installing or removing the
battery pack.
TO INSTALL BATTERY PACK: Align
rails (A) Fig. 4, on battery pack with
slots on tool and push battery pack
onto tool until it locks in place.
TO REMOVE BATTERY PACK:
Depress the battery release button (B)
Fig. 4, and pull battery pack out of
tool.
A
A
B
Fig. 4
ASSEMBLY
NOTE: This tool is shipped completely assembled. No assembly
time or tools are required.
LOADING FASTENERS
REMOVE BATTERY
PACK. ONLY USE APPROVED DELTA
FASTENERS.
A
1. Pull down on the nail pusher (A)
Fig. 5, until it locks in the open
position as shown in Fig. 6.
Fig. 5
2. Insert a strip of approved
fasteners, (B) Fig. 7. Orient
fasteners with points down, and
in contact with the bottom of the
magazine.
A
3. Pull nail pusher (A) Fig. 8,
completely to the rear, rotate
lever to the right and allow nail
pusher to slowly slide forward to
contact nails.
Fig. 6
A
B
Fig. 7
Fig. 8
12
OPERATION
Complete all steps of “LOADING FASTENERS” before using the tool.
1.
Install the battery pack.
2.
To fire, grip tool firmly to maintain
control, position nose of tool onto
work surface, push tool firmly
against work surface to depress
safety, as shown at (A) Fig. 9, and
then squeeze trigger (B) to fire a
fastener.
B
A
Fig. 9
ADJUSTING DEPTH OF DRIVE
The depth to which a fastener is driven is controlled by the depth adjustment
knob (A) Fig. 10. The depth of drive is factory adjusted to a nominal setting.
Test fire a fastener and check depth. If a change is desired, rotate the
adjustment knob (A) Fig. 10. Rotate
the knob clockwise, to increase the
depth of drive, rotate the knob
counterclockwise to decrease the
depth of drive. Test fire another
fastener and check depth. Repeat as
A
necessary to achieve desired results.
The amount of pressure required will
vary depending on the size of the
fastener and the material being
fastened.
Fig. 10
CLEARING A JAMMED FASTENER
If you should experience a nail jam, use the following procedure to clear the
jam.
REMOVE THE BATTERY FROM THE TOOL.
1. Retract nail pusher (A) Fig. 6, and remove any remaining fasteners (B)
Fig. 7.
2. Remove as much spring tension as possible by turning the depth
adjustment knob (A) Fig. 10, counterclockwise.
4. Install battery pack.
5. Press the tool safety (A) Fig. 9, against a block of scrap wood. Be sure
to keep hands away from driver blade area.
13
5. Slowly depress the nailer trigger (B) Fig. 10, to retract the driver blade,
but do not let the tool fully cycle. The spotting window (C) Fig. 11, can
be used to determine the position of the driver blade. When the front
end of the driver blade passes out of view, release the trigger.
REMOVE BATTERY
PACK FROM TOOL. THIS WILL
PREVENT ACCIDENTAL ACTUATION
WHILE THE JAM IS BEING CLEARED.
C
F
D
6.
Remove the two hex screws (D) Fig.
11, and protector plate (F).
7.
Remove jammed nails with a small
screwdriver or needle nosed pliers.
8.
Replace the battery pack.
9.
Release tension on drive spring by “dry” firing nailer into scrap wood.
Fig. 11
10. The nailer is now ready for normal operation.
TROUBLESHOOTING
For assistance with your tool, visit our website at www.deltamachinery.com
for a list of service centers or call the Delta Machinery help line at 1-800-2237278.
14
MAINTENANCE
KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts
should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic
parts. They could possibly dissolve or otherwise damage the material.
Wear ANSI Z87.1 safety glasses while using compressed air.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug are
making good contact in the outlet. Also, check for blown fuses or open circuit
breakers in the line.
LUBRICATION
This tool has been lubricated with a sufficient amount of high grade lubricant for
the life of the unit under normal operating conditions. No further lubrication is
necessary.
BRUSH INSPECTION (If applicable)
For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE•DELTA FACTORY
SERVICE CENTER.
At approximately 100 hours of use, take or send your tool to your nearest
authorized PORTER-CABLE Service Station to be thoroughly cleaned and
inspected. Have worn parts replaced and lubricated with fresh lubricant. Have
new brushes installed, and test the tool for performance.
Any loss of power before the above maintenance check may indicate the need
for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL
UNDER THIS CONDITION. If proper operating voltage is present, return your tool
to the service station for immediate service.
SERVICE
REPLACEMENT PARTS
When servicing use only identical replacement parts.
For a service parts list or to learn more about Delta Machinery visit our website
at www.deltamachinery.com
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to
wear from normal use. For assistance with your tool, visit our website at
www.deltamachinery.com for a list of service centers or call the Customer
Care Department at 1-800-223-7278. All repairs made by our service centers are
fully guaranteed against defective material and workmanship. We cannot
guarantee repairs made or attempted by others.
Should you have any questions about your tool, feel free to write us at any time.
In any communications, please give all information shown on the nameplate of
your tool (model number, type, serial number, etc.).
15
ACCESSORIES
A complete line of accessories is available from your Porter-Cable•Delta
Supplier, Porter-Cable•Delta Factory Service Centers, and Porter-Cable
Authorized Service Stations. Please visit our Web Site
www.deltamachinery.com for a catalog or for the name of your nearest
supplier.
Since accessories other than those offered by PorterCable•Delta have not been tested with this product, use of
such accessories could be hazardous. For safest operation,
only Porter-Cable•Delta recommended accessories should
be used with this product.
WARRANTY
Two Year Limited New Product Warranty
Delta will repair or replace, at its expense and at its option, any new Delta
machine, machine part, or machine accessory which in normal use has proven
to be defective in workmanship or material, provided that the customer returns
the product prepaid to a Delta factory service center or authorized service
station with proof of purchase of the product within two years and provides
Delta with reasonable opportunity to verify the alleged defect by inspection. For
all refurbished Delta product, the warranty period is 180 days. Delta may require
that electric motors be returned prepaid to a motor manufacturer’s authorized
station for inspection and repair or replacement. Delta will not be responsible for
any asserted defect which has resulted from normal wear, misuse, abuse or
repair or alteration made or specifically authorized by anyone other than an
authorized Delta service facility or representative. Under no circumstances will
Delta be liable for incidental or consequential damages resulting from defective
products. This warranty is Delta’s sole warranty and sets forth the customer’s
exclusive remedy, with respect to defective products; all other warranties,
express or implied, whether of merchantability, fitness for purpose, or
otherwise, are expressly disclaimed by Delta.
16
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable • Delta Power Tools are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta)
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
ARIZONA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
CALIFORNIA
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
ILLINOIS
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
San Diego 92111
7638 Clairemont Blvd.
Phone: (858) 277-9595
Fax: (858) 277-9696
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
COLORADO
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
MINNESOTA
Minneapolis 55429
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
MISSOURI
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
St. Louis 63119
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
PENNSYLVANIA
Willow Grove 19090 (Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
NEW YORK
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
MASSACHUSETTS
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
OHIO
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Houston 77043
4321 Sam Houston Parkway, West
Suite 180
Phone: (713) 983-9910
Fax: (713) 983-6645
WASHINGTON
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable • Delta products should be obtained by contacting any Porter-Cable • Delta Distributor, Authorized Service
Center, or Porter-Cable • Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will be directed to
the nearest Porter-Cable • Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.
Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos PorterCable • Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable • Delta, Centro de Servicio Autorizado o Centro
de Servicio de Fábrica Porter-Cable • Delta. Si no tiene acceso a ninguna de estas opciones, llame al 800-223-7278 y le dirigirán al Centro de
Servicio de Fábrica Porter-Cable • Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au
800-438-2486 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits PorterCable • Delta, s’adresser à tout distributeur Porter-Cable • Delta, centre de service agréé ou centre de service d’usine Porter-Cable • Delta. Si
vous n’avez accès à aucun de ces centres, appeler le 800-223-7278 et on vous dirigera vers le centre de service d’usine Porter-Cable • Delta le
plus proche.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
MANITOBA
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
QUÉBEC
1515 Ave.
St-Jean Baptiste, Suite 160
Québec, P.Q.
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
1447, Begin
St-Laurent, (Mtl), P.Q.
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICROSET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTERCABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THINLINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,
WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
7.2-PTG-F-1