Automatic WTLD018 Instruction manual

INSTRUCTION MANUAL
WTLD018
20V
Drill/Driver
Contents
Warranty
Introduction
Environmental protection
Description of symbols
Specifications
Safety instructions
Additional safety instructions for drills
Additional safety instructions for the charger
Additional safety instructions related
to the battery pack and battery safety
When to charge the battery
Know your product
Unpacking
Important information – Product care
Fitting and removing the battery pack
Battery charging To obtain the best life for the battery Battery indicator
Battery indicator under no-load
2 Speed gearbox
Using the drill
Drilling
Chuck replacement
Maintenance
2
3
3
3
3
4
5
6
Warranty Power Tools
1 Year Repair Warranty.
Register your warranty at www.automatictools.com.au
All warranty conditions can be found on the
www.automatictools.com.au website or email
help@globalpowerbrands.com or call 1800 909 909
7
8
9
10
10
10
11
11
11
12
12
12
14
15
15
2
Description of symbols
Introduction
The rating plate on your tool may show symbols.
These represent important information about the
product or instructions on its use.
Wear hearing protection. Wear eye protection.
Wear breathing protection.
Your new AUTOMATIC power tool will more than satisfy
your expectations. It has been manufactured under
stringent AUTOMATIC Quality Standards to meet
superior performance criteria.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years
of dependable service.
CAUTION. Carefully read through this entire Instruction
Manual before using your new AUTOMATIC Power Tool.
Take special care to heed the Cautions and Warnings.
Your AUTOMATIC power tool has many features that
will make your job faster and easier. Safety, performance,
and dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
Double insulated for additional protection.
Conforms to relevant standards
for electromagnetic compatibility.
Read these operating instructions well before
you use the tool
Do not throw the electronic waste products into
the domestic waste refuse. Such products must be
delivered to a recycling centre.
Environmental protection
Specifications
Recycle unwanted materials instead
of disposing of them as waste. All tools,
hoses and packaging should be sorted,
taken to the local recycling centre and
disposed of in an environmentally safe way.
Model WTLD018
3
Nominal battery voltage:
20V
Charger 230-240Vac 50 Hz
17W
Output:
23Vdc 400mA
Charging time:
3-5 Hours
Drill no load speed:
0-400/0-1300 rpm
Torque settings:
24 plus drill
Drill chuck capacity:
10mm Keyless
Weight (Including battery):
Weight (excluding battery):
1.42 kg
1.04 kg
Drilling capacity:
Steel
Timber
10mm
20mm
General safety rules
f) If operating the charger in a damp location is
unavoidable, use a residual current device (RCD)
protected supply with a max 30mA cut off limit.
Use of an RCD reduces the risk of electric shock.
3)Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
WARNING. Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c)Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a)Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b)Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c)Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d)Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e)When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
i) Children should be supervised to ensure that they do
not play with the appliance.
5) Battery tool use and care
5
a) Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
b) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
c) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
d) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
e) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for drills
Wear ear protectors with drills. Exposure to noise
can cause hearing loss.
• If possible, always use clamps or a vice to hold your work.
• Always switch off before you put the drill down.
• Ensure that the lighting is adequate.
• Do not put pressure on the drill, such that it slows the
motor down. Allow the drill bit to cut without pressure.
You will get better results and you will be taking better
care of your tool.
• Keep the area free of tripping hazards.
• Do not let anyone under 18 years operate this tool.
• Only use accessory bits in good condition.
• Before drilling, check that there is sufficient clearance for
the drill bit under the workpiece.
• Do not touch the bit after operation. It will be very hot.
• Keep your hands away from under the workpiece.
• Never use your hands to remove sawdust, chips or waste
close by the bit.
• Rags, cloths, cord, string and the like should never be left
around the work area.
• Support the work properly.
• If you are interrupted when operating the drill, complete
the process and switch off before looking up.
• Periodically check that all nuts, bolts and other fixings are
properly tightened.
• When using the drill, use safety equipment including
safety glasses or shield, ear defenders, and protective
clothing including safety gloves. Wear a dust mask if the
drilling operation creates dust.
If in doubt, do not plug in the tool. Using a power source with a
voltage less than the nameplate rating is harmful to the motor.
The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual will
be considered a case of misuse. The user and not the
manufacturer shall be liable for any damage or injury
resulting from such cases of misuse.
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this manual. All persons who use
and service the machine have to be acquainted with this
Manual and must be informed about its potential hazards.
Children and frail people must not use this tool. Children
should be supervised at all times if they are in the area in
which the tool is being used. It is also imperative that you
observe the accident prevention regulations in force in your
area. The same applies for general rules of occupational
health and safety.
The manufacturer shall not be liable for any changes made
to the tool nor for any damage resulting from such changes.
Even when the tool is used as prescribed it is not possible to
eliminate all residual risk factors. The following hazards may
arise in connection with the tool’s construction and design:
• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearing if effective ear defenders are not worn.
Additional safety instructions for the charger
• Your AUTOMATIC tool with Lithium Ion batteries may
only be charged with the specific designed AUTOMATIC
Lithium Ion battery charger purchased with the tool.
IT IS DANGEROUS TO USE ANY OTHER BATTERY
CHARGER TO CHARGE YOUR TOOL. Do not attempt
to charge the battery pack with any other charger than
the one supplied.
• If there is a problem with the battery or the tool, take it
to your nearest Authorised Service centre or phone and
speak with an experienced AUTOMATIC Customer Service
Representative for assistance in rectifying your problem.
• Before using the charger, read all the instructions, labels
and cautionary markings on the charger and battery pack
as well as the instructions on using the battery pack.
• Do not use the charger if it has been subjected to a
heavy knock, dropped or otherwise damaged in anyway.
Take the charger to an authorised service centre for a
check or repair.
• Do not disassemble the charger. Opening or removing
covers may expose you to dangerous voltages or other
risks. Incorrect reassembly can cause electric shock
when you use the tool or charger again. Take the charger
to an authorised service centre when service or repair
is required. Incorrect re-assembly may result in the risk
of fire, electric shock or electrocution. To reduce the risk
of electric shock, do not disassemble any part of the
product.
• DANGER. If the battery pack is cracked or damaged in
any other way, do not insert it in the charger
• Do not plug anything other than your AUTOMATIC tool
6
it will not be stepped on, tripped over or otherwise
subjected to damage or stress. Keep the lead away
from operating machinery.
• Do not pull on the lead of the charger to disconnect it
from the mains power socket.
• Do not use an extension cord unless it is absolutely
necessary. The use of an improper extension cord could
cause the risk of fire, electric shock or electrocution.
• Never attempt to connect two chargers together.
• Do not charge batteries or use the tool and battery
pack in locations where the temperature may be below
0°C or exceed 40°C such as alongside sheds or metal
structures.
• The battery can be charged or operated at temperatures
between 0° C and 40° C.
NEVER CHARGE YOU LITHIUM ION BATTERY BELOW
OR ABOVE TEMPERATURES RECOMMENDED
OTHERWISE FIRE OR SERIOUS DAMAGE TO THE
BATTERY PACK MAY OCCUR.
The most suitable temperatures to charge the battery pack
are between 20 - 25° C.
• If you wish to charge a second battery pack, unplug the
charger from the mains supply and leave it for at least
15 minutes. After this time you can charge a second
battery pack.
into the charger, as other objects may touch dangerous
voltage points or short out parts, which could result in fire
or electric shock.
• Do not place the tool or charger on an uneven surface,
as a fall may cause serious damage.
• Never place the tool or charger near or over a heat
source such as a radiator or heater.
• Do not operate the charger in a cabinet or other
enclosure unless proper ventilation is provided.
• Use the battery charger indoors only.
WARNING. Do not allow any liquid to come into contact
with the charger. There is a danger of electric shock. Do not
position the tool or battery charger near water; for example,
near a sink, wash bowl or toilet. Do not spill liquid of any
kind on the tool or charger. Doing so may short out parts,
causing damage to the product and creating the risk of fire
or electric shock.
Take the tool or charger to your nearest authorised service
centre for assistance in these circumstances:
• If liquid has been spilled into the tool or charger, or if rain
or water has touched the tool, Battery Pack or charger.
• If the tool or charger does not operate normally after you
follow the operating instructions.
• If the tool or charger has been dropped or damaged.
• If the tool or charger exhibits a distinct degradation in
performance.
• If the tool or charger is damaged in any way.
• If the battery pack is not charged within the time frame as
specified in this manual, turn charger off.
• To reduce the risk of an electric shock, unplug the
charger from the power supply before attempting to clean
it. To clean tool or charger, wipe with a damp cloth. Use
of any other cleaners is not recommended.
• Do not place any object on to, or allow anything to rest
on the charger.
• Make sure that the charger cable is positioned where
Additional safety instructions related
to the battery pack and battery safety
• Use only the AUTOMATIC batteries supplied with the
AUTOMATIC Tool or AUTOMATIC-approved replacements.
• Do not use the battery to power any device other than
the AUTOMATIC tool it was sold with.
• Charge the battery only with the AUTOMATIC charger
supplied with the tool or AUTOMATIC-approved
replacements and according to the instructions in the
AUTOMATIC Instruction Manual.
• Do not charge the battery in a place where static
7
condition and will not allow the pack to fall free from the
tool. If the clip is damaged or for any reason is not locking
the pack in place Do Not continue to use.
• Stop using the battery if it exhibits abnormal heat, odour,
colour, deformation, or is in an abnormal condition.
• If you detect leakage or a foul odour, it is especially
important to keep the battery away from fire. If battery
liquid leaks onto your skin or clothes, wash well with
clean water immediately. If liquid leaking from the
battery gets into your eyes, do not rub your eyes.
Rinse your eyes well (for at least 10 minutes) with clean
water, and consult a doctor immediately. Do not use a
leaking battery.
• Handle batteries with care to avoid shorting the battery
with conducting materials, such as nails, screws, metal
watch bands, rings, bracelets, and keys. The battery may
overheat and could burn you.
• After the battery has reached the end of its useful life,
we recommend recycling the materials at your local
municipal council recycling centre. DO NOT attempt to
replace the battery cells in the battery pack, repair or
modify any part of the battery pack assembly
• When recycling, make it nonconductive by applying
insulating tape to the terminals located on the battery.
electricity is generated nor let the battery touch something
that is statically charged.
• The battery can be stored at temperatures between
0 - 40° C.
NEVER STORE OR LEAVE YOUR LITHIUM ION
BATTERY IN TEMPERATURES OVER THAT
RECOMMENDED OTHERWISE FIRE MAY OCCUR.
Do NOT store the Lithium Ion battery anywhere that
the temperature can easily reach higher temperatures
than recommended - this includes garden type sheds,
and Vehicles where the inside temperature can climb
to dangerous levels in the direct sunlight and on high
temperature days. THINK BEFORE LEAVING YOUR
LITHIUM ION BATTERY PACK IN STORAGE.
• The battery can be charged or operated at temperatures
between 0° C and 40° C.
NEVER CHARGE YOU LITHIUM ION BATTERY BELOW
OR ABOVE TEMPERATURES RECOMMENDED
OTHERWISE FIRE OR SERIOUS DAMAGE TO THE
BATTERY PACK MAY OCCUR.
The most suitable temperatures to charge the battery pack
are between 20 - 25° C.
• Always allow the battery pack to cool down after
charging, do not place it in a hot environment such as a
metal shed or open trailer left in the sun.
• Take care where the tool is stored. Do not store in areas
of corrosive fumes, or salt air or similar conditions. Try
and store the tool in the packaging supplied with the tool.
• Do not dispose of the battery in a fire or put the battery
into a microwave oven, conventional oven, dryer, or highpressure container.
Under these conditions, the battery may explode.
• Never attempt to open the battery pack, puncture the
battery or subject the battery to strong physical shock.
• If the plastic housing of the battery pack breaks open
or cracks, immediately discontinue its use and do not
recharge it. Ensure the battery pack clip is in good
When to charge the battery
New battery packs are shipped in a low charge
condition and must be fully charged before use. It takes
approximately 8 hours to fully charge a new battery and
3-5 hours once the battery has been used in the tool
a few times.
Charging of batteries should not be undertaken casually.
Through the charging cycle the condition of the battery pack
should be monitored and the charge cycle turned
off at completion or at the end of the recommended time.
8
Know your product
11
10
This drill is mainly used for drilling in wood or metal sheet
and screwdriving. Use the tool and accessories only for
intended applications. All other applications are expressly
ruled out.
1. Keyless Chuck
1
2. Handle
16
3. Variable speed trigger switch with electric brake
4. Forward, Lock, Reverse control
9
12
5. Rechargeable lithium ion battery pack
6. LED battery indicators
7. Battery pack release button
8. Torque adjustment collar
8
9. 2 Speed gear selector
11. LED Charging indicators
3
12. Spirit level
13. Drill light
14 Lanyard carry strap
4
13
10. Plug pack charger
6
2
15 Double ended
driver bit
16 Chuck collar
6
9
12
15
7
14
5
9
Unpacking
In this condition, DO NOT force cool the pack by placing in
a freezer or similar device. Refer to the “Overload” section
in this manual.
Another feature of the drill/battery pack is the low voltage
cut out feature. This feature operates when the voltage
drops below a pre set value. When this occurs the tool will
automatically stop operating. To correct the situation you
need to either insert another charged battery into the drill
or recharge the existing battery, and then proceed with the
drilling/driving application.
Note: Attempting to restart the tool in this condition without
either recharging the battery or installing a battery with
charge will lead to drill restarting and then stopping again
after only a few seconds of operation.
These safety devices have been fitted for the safety,
reliability and life of the tool.
Due to modern mass production techniques, it is unlikely that
your AUTOMATIC Power Tool is faulty or that a part is missing.
If you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
Important information – Product care
These drill/drivers use Lithium Ion Battery Cells. Care
MUST be taken to ensure both the safety and life of the
pack is maintained. Ensure you have read all of the safety
notes in the previous pages before using the drill/driver.
Safety devices and circuitry for this tool are located in
the battery pack of this tool. The battery pack is a vital
component, not just for the power source, but also for
the full safety control for both the charging and also the
tool operation. Treat the battery pack with care and within
the guidelines of this manual. If the pack does become
immersed in water or any fluids, or is subject to a sever
drop etc, or it does not operate within the guidelines of
this manual, immediately STOP using the battery pack
and have it checked.
During operation avoid overloading the drill/driver. If
the drill driver is overloaded it will automatically STOP.
Overloading may occur for a number of reasons including
when the drill driver is pushed too hard or when using a
drill bit or attachment greater than what is specified. If you
do overload the drill driver during operation refer to the
“Overload” section in this manual.
Note: When the battery of the drill is at the lower end of the
charge, the drill is more susceptible to the overload condition.
As mentioned above the battery pack is an integral
component of this tool and it is fitted with thermal safety
devices. Running the drill at close to maximum load, or
continual resetting of the overload will cause the battery
pack to over heat. When a preset cell temperature is
detected, the battery pack will automatically STOP
operating and will not restart until the battery pack has
cooled to a safe level.
Fitting and removing the battery pack
To remove the battery pack from
the drill firmly press the battery
release button (7) at the front of
the battery pack, and slide the
battery forwards out of the tool.
To install the battery pack with
the drill, align the battery pack
with the drill base and insert
firmly into place by sliding the
battery backwards into position. Ensure the battery pack
locks into position. You will hear a click.
10
Battery charging
To obtain the best life for the battery
IMPORTANT. Before attempting to charge the battery,
check the charger and the battery to ensure the charging
equipment matches the battery supplied. The components
are all labelled with component numbers.
IMPORTANT. The battery will be fully charged after 3-5
hours, remove it from the charger after this time. Do not
leave a battery charging for longer than 24 hours.
Note: It is suggested to remove the battery from the drill for
the charging process. Do not attempt to use the drill while
the charger is connected to the battery.
1. To commence charging, plug
in the adaptor from the plug
pack charger (10) into the
back of the battery and insert
firmly into place.
2. Plug in the plug pack charger
and switch on at the power
supply. The green LED
indicator located on the
back of the battery will indicate that the battery is being
charged. The red light on the back of the battery indicates
the battery is connected to the turned on charger.
During the charging process the Red and the Green
lights are on. When the battery is fully charged the red
light remains on while the green light turns off.
3. The battery charging time is approximately 3-5 hours.
4. When the battery is fully charged turn off the plug pack
charger power supply from the mains and remove the
charger plug from the battery.
Both the battery pack and the charger may become warm
to touch. This is also normal and not an issue of concern.
Both the battery pack and plug pack charger are fitted
with thermal safety devices and they will shut down if the
temperatures become too high.
Never allow the drill to come to a complete stand still
before recharging. The battery should be placed on charge
whenever the battery is noticeably running down or the drill
no longer performs a task it previously performed.
Avoid allowing lose items like screws or nails etc. to be
stored with battery packs as these or similar items can short
battery packs and cause a fire or explosion.
Always unplug the plug pack charger when not in use and
store in a dry secure place.
Avoid charging or storing your battery in temperatures
below 0ºC and above 40ºC.
Battery indicator
Press the trigger switch fully so the motor is running at
no load full speed, press the indicator button and refer to
the LED lights. The LED lights indicate the level of charge
remaining in the battery.
The table overleaf explains the levels of charge
(low, medium and high).
11
Battery Indicator Under No-load
Red
Orange
Green Battery status
LED
LED
LED
indicator/description
ON
ON
ON
High: Battery is fully charged
ON
ON
OFF
Medium: Battery Approx 50% charge capacity.
ON
OFF
OFF
Low: Battery has less than 30% charge capacity and should be charged.
WARNING: Never use a damaged battery pack.
2 Speed gearbox
Using the drill
Trigger switch
Use the forward/reverse switch
(4) to select the direction of
rotation, then pull the trigger
(3) This trigger switch is an
electronic variable speed control
which enables the user to vary
the speed continuously. The speed varies according to
how far the trigger switch is depressed. The further it is
depressed the faster the chuck will rotate and the lighter it is
depressed, the slower it will rotate.
To stop the drill, release the trigger switch.
Note. The variable Speed control fitted to this drill is NOT
intended to be used for long periods of time during the
operation of the task being performed. Use the variable
speed to start drilling and screwing tasks, and then fully
depress the trigger once the task has started.
CAUTION. Extended use of the variable speed under load will
overload and then permanently damage the speed control.
The 2 Speed Gearbox allows you
to select a gear with the optimum
speed and torque to suit the
application.
Note. When changing the drill
selector ensures the drill is not
operating.
To select the LOW gear (low
speed, high torque setting), push
the gear selector (9) backward,
towards the back of the drill. The
symbol “I” will be displayed.
To select the HIGH gear (high
speed, low torque setting), push
the gear selector (9) forward,
towards the chuck.
The symbol “II” will be displayed.
12
Temperature Cut Out
If the drill is constantly overloaded, or the drill is used
constantly at maximum rating in high ambient conditions,
the battery cells may over heat causing the battery pack
to shut down.
When this occurs you will need to immediately stop drilling
and allow the battery cells to reduce the temperature.
To reduce the temperature of the cells remove the battery
pack from the drill and place the battery pack in a free air
environment, out of direct sunlight or any other heat source.
DO NOT force cool the pack in any way. Do not place in
refrigerators or freezers.
When the battery pack has cooled down it can again
be used to operate the drill, as long as the load or the
conditions causing the original excessive temperature
has been corrected.
Low voltage cut out
The battery pack used on this tool is fitted with a low
voltage cut out feature within the circuitry.
The low voltage cut out feature operates when the voltage
drops below a pre set value. This feature automatically
stops the drill from operating (similar to that of the over
load condition). When this condition occurs you will need
to either insert another battery into the drill or recharge the
existing battery.
The low voltage cut out feature has been added to
maximise the tools life. When this occurs, recharge the
battery pack by following the battery charging section in
this manual.
Note: Attempting to restart the tool without either recharging
the battery or installing another battery (with charge) will
lead to drill restarting and then stopping again, after only a
few seconds of operation.
Forward/reverse switch
Note. You can only change
the direction of rotation of the
drill using the forward/reverse
switch when the trigger is NOT
depressed.
This switch (4) will allow you to
change the direction of the motor
while the trigger switch is not
depressed.
Drilling uses the forward mode.
The reverse mode is intended
for the removal of screws and
assisting to remove jammed
drill bits.
Drill Overload
This drill is fitted with an
overload protection. If the drill is excessively forced, or the
task being performed is too great for the drill, the drill will
automatically go into an overload mode. When the drill goes
into overload, the drill will automatically and suddenly STOP.
To reset the overload, simply release the trigger. When the
trigger is pressed again, the drill will restart. Resume work
after the overload has been reset, but reduce the load by
using a smaller drill bit or re-sharpen the existing drill bit and
reduce the amount of force placed on the drill.
CAUTION. Do not continue to overload the drill and
constantly reset the overload. Doing this will cause the
battery cells to over heat.
13
Adjustable torque
These drills are equipped with
24 torque settings plus one drill
setting which are controlled
by the torque collar (8). All of
the torque settings are clearly
identified on the torque collar.
To adjust the torque setting you
rotate the torque collar. Rotate
the torque collar clockwise to
increase the torque setting
and rotate it anti-clockwise to
decrease the torque setting.
Controlling the torque allows
for better control when using
the drill on specific tasks and
prevents over-fastening and
over-tightening.
For drilling, always use the use the Drill position by aligning
the Drill symbol with the triangular indicator on the front face
of the drill near the torque collar.
For setting the torque position, select a low setting on
the torque collar and align the selected symbol with the
triangular indicator on the top of the drill. Increase gradually
to set the correct torque. It is better to use a scrap piece of
material if possible to set the torque.
Inserting and removing bits
These drills have a keyless
chuck, which means that a chuck
key is not needed to secure a bit
in the drill.
Open the chuck by holding the
chuck collar and unscrewing
the chuck in an anti-clockwise
direction.
Do this sufficiently enough to
allow the drill bit to enter the jaws of the chuck.
Ensure the bit is fully inserted,
so that the chuck jaws grip the
straight section of the bit.
While holding the chuck collar
in place, rotate the chuck
clock-wise until the jaws tighten
on the bit. The chuck needs to be
tightened firmly to ensure the bit
is held securely.
To remove the bit, hold the chuck
collar while rotating the chuck
sharply in an anti-clockwise
direction, sufficiently enough to
allow the bit to be removed.
Drilling
Drilling metals
• Always clamp sheet metal.
• Support thin metal with a block of wood to avoid
distorting it.
• Use a punch to mark the centre of the hole.
• Use a suitable lubricant for the material you are
working on,
USE:
FOR:
Oil
Steel
Turpentine or paraffin
Aluminium
Do not lubricate
Brass, copper or cast iron
Drilling plastics and plastic coated chipboard
• Use high speed drill bits
• See drilling wood below
14
Maintenance
Drilling wood
• Clamp a piece of scrap wood to the back of your work to
prevent splintering.
All drilling operations
• Mark off the centre of the hole using a centre punch or nail.
• Don’t force the drill, let it work at its own pace
• Keep the drill bit sharp.
• Reduce pressure, as the drill is about to break through
the item being drilled.
• Store the tools, instruction manual and where necessary
the accessories in the original packaging. In this way
you will always have all the information and parts ready
to hand.
• Do not throw used batteries into fire or water. There
is a danger of explosion! Please hand in non-working
or used batteries, or tools with built-in batteries, to the
environmentally-safe disposal unit at a municipal wastedisposal centre, or to your dealer.
• If the cordset of the charger is damaged or worn, have it
repaired or replaced by an authorised service centre.
Chuck replacement
The chucks of reversible drills are always fixed by a screw
with a left-hand thread. The screw, which is located in the
centre of the chuck, must be removed before the chuck can
be removed. To remove the screw, turn it in a clockwise
direction. The chuck can now be removed by unscrewing it
anti-clockwise. If you have trouble removing the chuck take
the drill to your nearest authorised service centre for chuck
replacement.
CAUTION. Always ensure that the drill is switched off
and the battery pack is removed before making any
adjustments.
15
DISTRIBUTED BY;
Global Power Brands International Pty. Ltd.
PO Box 413 Mooroolbark VIC 3138
ABN. 39 131 999 914
Ph. 1800 909 909
help@globalpowerbrands.com