NXD/T-1500VG 15" Modero® VG Series Touch Panels - AV-iQ

Installation Guide
NXD/T-1500VG
The VG-Series of touch panels can be fitted for either Video (Composite) or RGB
(Component) via the use of two kit configurations: Video Kit and RGB Kit. Each kit comes
with its own group of standard components that are specific to its configuration.
The panel's sizeable screen size allows users to automate their environment seamlessly and
with minimal effort. It combines a sleek design with innovative multimedia functionality.
Sleep/Setup Access Button
1500VG Specifications (Cont.)
Supported Audio
Sample Rates:
48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz, 12000Hz,
11025Hz, and 8000Hz.
Certifications:
FCC Part 15 Class B, CE, and EN 60950
Supported Transport
Protocols:
• RTP (MPEG-2/MPEG-4 Transport Stream)
• UDP (MPEG-2 Transport Stream)
Supported Audio
Codecs:
• Advanced Audio Coding (AAC)
• MPEG Audio Level 2 (MP2)
• MPEG Audio Level 3 (MP3)
Supported Video
Codecs:
• MPEG-2
• MPEG-4
Front Panel
Components:
• Light Sensor: Photosensitive light detector for automatic adjustment of
the panel brightness
• Motion Sensor (PIR): Proximity Infrared Detector to wake the panel
when panel is approached
• Front Setup Access Button: Pushbutton (grey) used to either put the
panel into a "sleep" or "wake" state
• Microphone: Used for intercom applications
• Speakers: Stereo output with a frequency response of 450 Hz - 7 KHz
Rear Panel
Components:
• RGB Connector: Made available only by using an NXA-RGB interface
card installed within the touch panel. Used with Component/RGB
signals
• Audio/Video Connector: RJ-45 connector for communication of
differential audio/video signals
• Ethernet 10/100 Port: RJ-45 port for 10/100 Mbps communication
• PWR Connector: 2-pin 3.5 mm mini-Phoenix connector
• Stereo Output Connector: Stereo output through a 3.5mm mini-jack
• USB Connector: Two Type A USB ports
• Mini-USB Connector: 5-pin Mini-USB connector
Operating / Storage
Environments:
•
•
•
•
Included
Accessories:
• Installation Kit for 15" NXD panels (KA2251-02):
- 2-pin mini-Phoenix connector (41-5025)
- Four Drywall clips (62-5924-05) and #6 -metal strips (80-0192)
- Three Phillips-head screws (#4-20 x 0.250 Black) (80-0114-08)
- Two CAT5 Suppression Ferrites (04-0014)
• Installation Kit for 15" and 17" NXT panels (KA2251-04):
- 2-pin mini-Phoenix connector (41-5025)
- One CAT5 Suppression Ferrites (04-0014)
- Three Phillips-head screws (#4-20 x 0.250 Black) (80-0114-08)
• Included within the RGB Kit:
- Modero VG Touch Panel (NXD/NXT-1200/1500/1700VG)
- NXA-AVB/RGB Breakout Box (FG2254-11)
- NXA-RGB internal RGB/VGA Interface Card (FG2260)
- NXA-RGBCBL, 15-pin to 5X BNC RGB Breakout cable (FG2250-80)
- NXA-MTC/RGB Modero 10’ foot Table Top Cable with RGB
connector (CA2250-70)
• Included within the Video Kit:
- Modero VG Touch Panel (NXD/NXT-1200/1500/1700VG)
- Modero 10’ foot Table Top Cable (CA2250-50)
- NXA-AVB/ETHERNET Breakout Box (FG2254-10)
Other AMX
Equipment:
•
•
•
•
•
•
•
•
•
FIG. 1 1500VG Touch Panel
ATTENTION!
Verify you are using the latest NetLinx Master and Modero touch panel firmware
(available from www.amx.com). Verify the TPDesign4 program being used is Version
2.6 or higher, and download the latest G4 Support Files from www.amx.com.
Modero 1500VG Touch Panels
With Video Kit
NXD-1500VG (FG2253-61V)
15" Modero VG Series Wall/Flush Mount Touch Panel
(Supports Composite Video Input)
NXT-1500VG (FG2252-61V)
15" Modero VG Series Table Top Touch Panel
(Supports Composite Video Input)
With RGB Kit
NXD-1500VG (FG2253-61RGB)
15" Modero VG Series Wall/Flush Mount Touch Panel
(Supports RGB/Component Video Input)
NXT-1500VG (FG2252-61RGB)
15" Modero VG Series Table Top Touch Panel (Supports RGB/
Component Video Input)
Specifications
1500VG Specifications
Dimensions (HWD):
• NXD-1500VG (with faceplate): 14.37" x 15.20" x 3.31"
(36.50 cm x 38.61 cm x 8.40 cm)
• NXT-1500VG (Fully raised): 12.94" x 14.95" x 11.73"
(32.87 cm x 37.97 cm x 29.78 cm)
• NXT-1500VG (Fully lowered): 7.45" x 14.95" x 11.72"
(18.92 cm x 37.97 cm x 29.77 cm)
• CB-TP15 (conduit/wallbox): 13.48" x 14.18" x 3.49"
(34.24 cm x 36.00 cm x 8.85 cm)
• MB-TP15 (VESA mounting box): 14.37" x 15.19" x 3.59"
(36.50 cm x 38.59 cm x 9.12 cm)
Power:
• Constant current draw: 3.7 A @ 12 VDC (stand-alone)
• Startup current draw: 5.5 A @ 12 VDC (stand-alone)
Minimum power
supply required:
PSN6.5 Power Supply (FG423-41)
- using accessories can increase the power draw requirements
Memory:
256 MB on-board memory
Compactflash:
2GB or greater (upgradeable to 4GB - see Other AMX Equipment).
Note: AMX may increase Compactflash size at any time in response to
market availability.
Weight:
• NXD-1500VG: 13.45 lbs (6.10 kg)
• NXT-1500VG: 17.15 lbs (7.78 kg)
LCD Parameters:
•
•
•
•
•
•
•
•
•
Aspect Ratio: 4:3
Brightness (luminance): 400 cd/m2
Channel transparency: 8-bit Alpha channel transparency
Contrast ratio: 300:1
Display area (HW): 304.13 mm x 228.10 mm
Display colors: 16 million colors (24-bit color depth)
Dot/pixel pitch: 0.297 mm
Screen resolution (HW): 1024 x 768
Video formats: NTSC, PAL, and SECAM (shown within variable-size
video windows)
Active Screen Area:
11.97" x 8.98" (30.41cm x 22.81cm)
Viewing Angles:
Vertical: + 85° (up from center) and - 85° (down from center)
15" Modero® VG Series Touch Panels
Operating Temperature: 10° C (50° F) to 40° C (104° F)
Operating Humidity: 20% to 85% RH
Storage Temperature: -20° C (-4° F) to 60° C (140° F)
Storage Humidity: 5% to 85% RH
CB-TP15 Conduit/Wallbox (FG032-10)
CC-USB (Type A) to Mini-B 5-Wire programming cable (FG10-5965)
Kensington Lock Bracket (FG2259-10) (optional only with NXTs)
MAX-CSE MAX Video Encoder (FG2178-70)
MB-TP15 Universal VESA Mounting Box (FG032-50)
NXA-AVB/ETHERNET Breakout Box (FG2254-10)
NXA-AVB/RGB Breakout Box (FG2254-11)
NXA-BASE/B (FG2255)
NXA-MTC/RGB Modero 10’ foot Table Top Cable with RGB connector
(CA2250-70). This cable is not wall-rated for NXD models.
• NXA-PCI80211G Wireless Card (FG2255-04)
• NXA-RGBKIT RGB upgrade kit for Composite Video touch panels
(FG2255-11):
- NXA-AVB/RGB Breakout Box (FG2254-11)
- NXA-MTC/RGB Modero 10’ foot Table Top Cable with RGB
connector (CA2250-70)
- NXA-RGB internal RGB/VGA Interface Card (FG2260)
- NXA-RGBCBL, 15-pin to 5X BNC RGB Breakout cable (FG2250-80)
- NXT Table Top replacement I/O plate with RGB connector opening
(62-2250-59)
- NXD WallMount replacement adhesive overlay for existing I/O plate
(53-2250-03)
Note: The NXT replacement I/O plate is a single piece which is meant to
be swapped-out with the pre-existing plate shipped with Composite
Video panels. On NXD panels, the RGB connector opening is pre-drilled
into the I/O plate but can only be accessed by replacing the adhesive
cover and maintaining the existing overlay. When upgrading NXD panels
with this kit, don’t replace the NXD I/O plate, only the adhesive cover.
• NXA-RGBCBL, 15-pin to 5X BNC RGB Breakout cable (FG2250-80)
• NXA-RK15 Rackmount kit for 15" Wall Mount panels (FG2904-51)
• NXT-BP (FG2250-10)
• NXT-CHG (FG2250-50)
• PSN6.5 Power Supply (12 VDC) (FG423-41)
• Upgrade Compactflash (pre-programmed with firmware):
NXA-CFTP4G, 4GB Compactflash Upgrade (FG2116-08)
Panel Connectors
Wiring for Unbalanced Audio
FIG. 2 shows the connectors located on the 1500VG Modero Multimedia touch panels.
Composite/RGB and
ass-thru control (CAT 5)
Ethernet
(CAT5)
A
Use FIG. 5 to configure an unbalanced audio connection.
GND
PWR
Keyboard/Mouse
USB connectors
L
IN+
GND
RGB
AUDIO/VIDEO
ETHERNET
Unbalanced IN
(Jumper IN- to GND)
Left Channel
IN-
12VDC
Stereo
Output
Audio-Video from
AVB/RGB (CAT 5)
Right Channel
IN-
PROGRAM
PWR
Unbalanced IN
(Jumper IN- to GND)
IN+
Mini-USB
(Program Port)
AUDIO IN
MIC OUT
FIG. 2 Connector layout
GND
NXA-AVB/RGB Breakout Box
OUT-
FIG. 3 shows the front and rear connectors on the NXA-AVB/RGB breakout box. This
breakout box can be mounted on either a horizontal flat surface or into an equipment rack
(using an optional AC-RK Rack Kit).
Unbalanced OUT
Microphone
OUT+
FIG. 5 Wiring the rear AUDIO IN and MIC OUT for use with Unbalanced Audio
S-Video Chroma
Composite/S-Video Luma
Audio In
Mic Out
RGB/Component In
RGB (to internal NXA-RGB card)
Audio/Video (to panel)
Ethernet (to panel)
Wiring for Balanced Audio
Use FIG. 6 to configure a balanced audio connection.
Ground signal
GND
Return signal
OUT-
Balanced OUT
Line signal
OUT+
FIG. 6 Wiring the rear AUDIO IN and MIC OUT for use with Balanced Audio
(front)
(rear)
Power (to panel)
USB
Power
Ethernet In
Modero Setup and System Connection
1.
2.
FIG. 3 Connector layouts on the NXA-AVB/RGB Breakout Box
Wiring the NXA-AVB/RGB Connectors and Cables
The inputs and outputs on the breakout box are separated into front and rear connectors.
The rear connectors are used to input external signals.
The front connectors are used to communicate signals between the NXA-AVB/RGB and a
target Modero panel. FIG. 4 provides a layout of the wiring connections on both sides of the
breakout box.
3.
Note: Power should be applied to the NXA-AVB/RGB only after all connections have
been secured onto both the breakout box and the target panel.
6.
4.
5.
7.
F
RGB/Component In
(HD-15)
Carefully remove the panel from the shipping box, peel the protective plastic cover
from the LCD and apply power to the panel.
From below the LCD, press the grey Front Setup Access button for 6 seconds
(passing-over the Setup page) to access the Calibration setup page and follow the
on-screen instructions.
Press the grey Firmware Setup Access button for 3 seconds to open the Setup page
and touch the on-screen Protected Setup button.
Enter the panel password into the keypad. Factory default is 1988.
Press the Device Number field to open the on-screen Device Number keypad and
enter a value for the panel (default is 10001).
Press Done when finished and press the on-screen Reboot button to cycle power to
the panel.
Repeat step 3 to access the Protected Setup page and touch the System Settings
button to open the System Settings page (FIG. 7).
R
O
Microphone Out
GND
Out (-)
(4-pin captive wire)
Out (+)
N
T
In (+)
GND
Audio In - Right Channel
In (-)
(6-pin captive wire)
In (+)
RGB
(CAT5)
Audio/Video
(CAT5)
USB
(Type-B)
Power
supply
NXA-AVB/RGB
In (-)
(6-pin captive wire)
Breakout
Box
GND
Audio In - Left Channel
Ethernet
(RJ-45)
R
Comp/Y (BNC)
A
C (BNC)
R
Ethernet
Out (CAT5)
Panel’s connection information
E
Power to
touch
panel
FIG. 4 NXA-AVB/RGB Breakout Box connector wiring diagram
Use the NXA-MTC/RGB cable to provide both communication and 10/100 network
connectivity between the target panel, NXA-AVB/RGB, NetLinx Master, and the network.
The RJ-45 connector is used to route the signals connected to the RGB / Component input
port on the rear of the AVB/RGB Breakout Box to the VG-Series Modero panel.
Standard CAT5 cable can be used for this connection with short cable runs under 50 feet
(15.24 m).
For cable runs over 50 feet (15.24 m), AMX recommends using the Belden Brilliance
VideoTwist 7987. This Belden cable is not CAT5 compliant, but is designed to control skew
between the red, green, and blue video signals. Therefore, for longer cable runs, the video
quality will be much higher using the Belden VideoTwist 7987 cable versus standard CAT5
(or other Ethernet compliant cables).
Master’s connection information
FIG. 7 Sample System Settings page
8.
9.
10.
Toggle the Type field to Ethernet and enter both the System Number and IP Address
of the target Master.
Enter a valid Username and/or Password (if the target Master is secured).
Press the Back button and then press the on-screen Reboot button to save the
changes and cycle power.
Additional Documentation
For more detailed installation, configuration, programming, file transfer, and operating
instructions, refer to the VG-Series Modero Touch Panels Instruction Manual available online at www.amx.com.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
9/11
©2011 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2252-61
REV: K