Thunder Tiger 3D Sukhoi 31 组装手册

Add to my manuals
7 Pages

advertisement

Thunder Tiger 3D Sukhoi 31 组装手册 | Manualzz

Thunder Tiger 3D Sukhoi 31 assemble Manual

http://www.manuallib.com/file/2714099

From ManualLib.com

ManualLib.com collects and classifies the global product instrunction manuals to help users access anytime and anywhere, helping users make better use of products.

Home: http://www.manuallib.com/ Chinese: http://www.shuomingshuku.com/

This Manual: http://www.manuallib.com/file/2714099

MEMO

Assembly Manual

THUNDER TIGER CORP.

www.thundertiger.com

12

This Manual: http://www.manuallib.com/file/2714099

No. 4347

Specification:

Wing Span: 29.3” (830mm)

Length: 29.8” (845mm)

Weight: 14oz.~15oz. (420~430g)

Warranty

This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.

It does not cover any damage caused by use or modification. The warranty does not extend beyond the product itself and is limited only to the original cost of the kit. By the act of building this userassembled kit, the user accepts all resulting in liability for damage caused by the final product. If the buyer is not prepared to accept this liability, it can be returned new and unused to the place of purchase for a refund. Neither your dealer nor Thunder Tiger Distributors, can accept kits for return if construction has begun.

Notice: Adult Super Vision Required

This is not a toy. Assembly and flying of this product requires adult supervision.

Read through this book completely and become familiar with the assembly and flight of this airplane.

Inspect all parts for completeness and damage. Browse www. thundertiger. com for customer service if you encounter any problems.

JE6942

1

INTRODUCTION

Introduction

Thank you for your purchase of the Thunder Tiger 3D Sukhoi EP. You can make this proven 3D fun flyer easily do any aerobatics and 3D maneuvers, includes Knife Edge, Hovering, Torque Rolls, Cobra...etc.

Made of Anti-Impact EPP material that reduce the crash damage. Very good for those who are interested in learning 3D-aerobatics or experienced 3D pilots who are looking for a relaxed practicing plane that can be used both outdoor and indoor.

The 3D Sukhoi EP is designed for intermediate pilot minded. Before beginning the assembly read the instructions thoroughly to give an understanding of the sequence of steps and a general awareness of the recommended assembly procedures. Check the entire contents of your kit against the parts drawing and photos to make sure that no parts are missing or damaged. This will also help you to become familiar with each component of your plane. If you find that any of the parts are either missing or damaged, please contact Thunder Tiger Distributors for Customer Service.

TABLE OF CONTENTS

Introduction.........................................................................................................................2

Parts Drawings........................................................................................................................3

Wing…………………..........................................................................................…….…...……...4

Tail........................................................................................................................................5

Motor………...........................................................................................………….....……........6

Landing Gear………........................................................................................………….....……..7

Setup....................................................................................................................................8-10

.............................................................................................................................11

OTHER ITEMS REQUIRED FOR ASSEMBLY

A checklist is provided as below which will make shopping for these items easier.

Brushless Motor: Recommend

OBL29/09-07A motor ( No.2354) Radio: A 4-channel radio with

3 micro servos and mini receiver are required.

C o n t r o l l e r : A C E B L C 1 2 A

(No. 8026) is a perfect controller that controlling OBL motor efficiently.

Battery: Recommend the use of a ACE Power Lipo battery

3S1P 1100mAh(No.2804).

Adhesives: You will need the t h i c k i n s t a n t ( c y a n o a c r y l a t e ) adhesives.

Extension Wire: 2 pieces of extension wire in length of 12”.

Propeller: There is a 11x8 prop. in the kit, yet it is only for test flight.

Recommended APC 10x4.7 SF propeller for high performance 3D aerobatics.

2

TOOLS AND SUPPLIES NEEDED

Paper Towel

Hobby Knife

Ruler

Pen, Pencil or Marker

Phillips&Flat Head Screw Drivers

Scissors

Nose Plier

Drill Bit 5/64” (2mm)

This Manual: http://www.manuallib.com/file/2714099

PARTS DRAWINGS

Open the box and check that you have all the parts as shown below.

AS6647 Fuselage

Fuselage (1)

Velcro A (1)

Firewall (1)

AS6648 Main Wing

Velcro B (1) Glue (1) Tail Gear (1) 2.3x12mm Wood Screw (1)

Wing (1)

Hinge (8)

Aileron (L/1,R/1)

AS6649 Tail

1.5 CFK Rod 230 (2) 1.5 CFK Rod 98 (2) 1.5 CFK Rod 390 (2)

AS6653 11x8 SF Propeller

Horizontal Tail (1)

Vertical Fin (1)

5 11X8 Propeller (1)

AS6652 Control Horn

2 CFK Rod 340 (1)

FRP Control Horn (4)

1.5 CFK Rod 180 (2)

AS6650 Pushrod

Clevis (4)

Pushrod (4)

AS6651 Landing Gear

Mount (2)

Landing Gear (2)

Wheel Colar (2)

Hinge (4)

No.2354 OBL 29/09-07A

Reinforced Plate (1)

Cross Mount (1)

3x6mm Sink Screw (4) 2x6mm Screw (3) 3x10mm Wood Screw (4)

Prop Nut (1)

Adaptor (1) Outrunner Brushless Motor 29/27-07A (1)

AS6336 Wheel

Superlite Wheel (2)

3

WING

TAIL

Rudder

1.Carefully and slowly insert the main wing into the fuselage then center it in place.

4. Install four CA hinges on the aileron as shown, carefully use the sharp hobby knife to cut the slots on aileron and trailing edge of wing for the hinges.

7. Glue the FRP control horn and elevator reinforced plates together as shown. Make sure the two rein forced pieces are glued properly at each side of elevator so the control horn could be installed perpendicularly at left.

10. Cut a slot at the bottom rear fuselage, install tail skid in place with CA glue.

2. Glue the CFK rods on Aileron, Rudder and Elevator as indicated.

5. Attach the aileron to the trailing edge of main wing then apply CA glue to all hinges and make sure they are jointed well. Do the same procedure on the other aileron.

8. Do the same procedure as elevator control horn to install the rudder control horn as shown at right.

11. Drill 5/64”(2mm) pilot holes for mounting the elevator servo, next connect a 12” extension wire before you secure the servo in place. Do the same way on rudder servo.

3. Install and center the horizontal tail in place, make sure the horizontal tail is perpendicular to the vertical fin and parallel with the main wing. Next CA the main wing and horizontal tail firmly in place.

6. Install four CA hinges on the rudder, use the same way as you did on aileron. Next glue the rudder on the vertical fin.

4

This Manual: http://www.manuallib.com/file/2714099

9. Do the same procedure on both aileron control horns.

12. Locate the pushrod and clevis, thread the clevis at least 6mm then snap onto the FRP control horn, make sure servo is in neutral position then make

Z-bend and cut the excess pushrod. Insert the

Z-bend end to the servo horn and secure the servo horn on the servo as shown. Do the same way to the other pushrod.

5

MOTOR

LANDING GEAR

13. Secure the aileron servo and attach the aileron pushrods as shown.

16. Open the hatch and place the Lipo battery in the compartment. Secure the battery in place with the

2.3X12mm wood screw.

19. Apply the furnished glue on fuselage opening and Velcro, wait for 10 minutes before gluing them together. Hint: It is very important to wait for couple minutes before gluing together. You may blow the glue area and it will be cured faster. Do not separate the Velcro. Carefully attach the Velcro to the fuselage opening on one side first then apply the other side of fuselage to the Velcro.

22. Trial fit the landing gear wire and mount first,

CA the wire and landing gear mount in place when satisfied. Note two landing gear wires are angled properly.

14. Secure the cross mount on brushless motor with four 3x6mm sink screws. Install the adaptor to the brushless motor with three 2x6mm screws as shown.

17. Connect the receiver and controller properly, secure these electric devices with the furnished wide Velcro.

20. Locate the landing gear wires, mounts, wheels and stoppers. Bend the wire as shown and trim the excess wire.

23. Install the wheel and CA the wheel stopper. Make sure wheel rotates freely.

15. CA the firewall in place then install the brushless motor on the firewall with four 3x10mm wood screws.

Next install the furnished propeller and with prop nut.

If user would try extreme 3D then APC 10x4.7

SF is recommended.

6

18. Locate the narrow/long Velcro strip and trim as shown to accommodate the fuselage opening.

Note: do not cut it off and make sure it is connected.

This Manual: http://www.manuallib.com/file/2714099

21. Locate the landing gear mounting slot where near the leading edge of main wing as shown.

Congratulations! Now you are ready to fly. Make sure to adjust the plane as the suggestion in next

two pages.

7

CONTROL THROWS

Control Throws

The following control throw of 3D Sukhoi EP is merely a starting point for your radio setup and can be tailored to fit your flying style.

For all three models the aileron and elevator of the same throws but rudder are different as shown below.

Aileron-Low Rate

2” (50mm)

2” (50mm)

Aileron-High Rate

2-3/4” (70mm)

2-3/4” (70mm)

Elevator/Low Rate

1-3/4” (46mm)

1-3/4” (46mm)

Elevator/High Rate

Rudder /Low Rate

2-1/4” (58mm)

2-1/4” (58mm)

Rudder/High Rate

BALANCE

It is important to balance the plane to get correct C.G. before you fly.

Balance Point as indicated in each diagram.

2-1/2” (65mm)

2-1/2” (65mm)

3” (79mm)

3” (79mm)

3” (79mm)

2” (53mm)

LONGITUDE BALANCE

C.G. Must be set on thrust line

LONGITUDE BALANCE

C.G. is too low C.G. is correct

As 3D planes do a lot of hovering so it is very important to do longitude balance to make hovering much more stable. Try to create a small hole after the motor and on the thrust line. Get music wire or string then thread the wire through the hole. Make sure that model hangs perfectly vertical as illustration. If not then try to adjust the location of battery, receiver or ESC to get good longitude balance.

Congratulations

Your done, may you have many successful flights filled with fun and lots of 3D maneuvers.

Thank you for purchasing this plane from Thunder Tiger and we look forward to providing you with other great R/C products in the near future.

SETTING UP FOR 3D FLIGHT

Servo Output

High Rate

Low Rate

Stick Travel

Note: For the best flight performance of the Sukhoi, A high center of gravity is important.

8

This Manual: http://www.manuallib.com/file/2714099

1/3 1/3 1/3

9

SETUP

Exponetial

To make your 3D flight successful, the most important is to set up your radio properly and fine-tune the exponential. We would suggest that could show the exponential graph as the illustration.

Normally this computerized radio has dual rates or even triple rates. Once you fly it fine with low rate in normal flight. Next you will have to set up 3D rate.

We suggest the 3D-rate setting is same as low rate setting around 1/3 of the total stick travel in the beginning. If you look at the graph , the middle section of 1/3 travel are most likely the same at low rate and

3D high rate .Beyond this middle section the 3D rate setting is far higher than the low rate.

SIMULATOR

A good tool to practice 3D easier is to fly simulator.

One may say simulator is not realistic but this is not true. There are some simulators available in the market and its scenery and performance are just like a real thing .For example, Aerofly Pro Deluxe USB v e r s i o n f r o m i k a r u s o r R e a l F l i g h t G 3 f r o m

Greatplanes are all good simulators you can choose from .

Simulator is a must buy tool if you seriously want to fly

3D aerobatics. There is no genius or born 3D pilot, remember that practice makes perfect.30 minutes a day on a simulator can help you do hovering, torque roll easily as well as other aerobatics. If you would like to be a good 3D pilot, flying everyday is necessary.

The reaction to control the airplane will be more nature. As there is no time to think when you do 3D aerobatics.

Simulator practice might be perfect yet suggest to do some actual flying as the supplemental so it will not go too far from the real thing as there are many things that you can not learn in screen.

FLYING

Even though you set up the airplane , it needs to be setup and fine-tuned in the air. Always start on low rates when launch the airplane or take off of the ground. Once you fine trim the airplane in the air then tune the exponential setting, you will be able to fly it all the time on the 3D rates.

Once you got confidence to do hovering or do 3D aerobatics, we suggest you fly it near you. The closer the airplane, the better you fly it near you. The closer the airplane, the better you can control the plane as you can see it very clear even if it has a slight movement. The other advantage is the lower or closer to ground, the less potential energy. It is useful for a dead battery or ESC cut off suddenly.

10

This Manual: http://www.manuallib.com/file/2714099

30cm

3x10mm

2x6mm

11

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents