DAS NX-148E LCD Codepad Installation manual

Installation manual
HILLS RELIANCE
Hills Reliance Control Panel
Thank-you for choosing the Hills Reliance Control Panel!
The Hills Reliance security control panel from Hills Industries represents a new approach to security system design.
Drawing on experience from the world market, Hills has developed the most flexible, durable, and user-friendly control ever
seen in our industry. Featuring sophisticated software that allows up to 99 users to interface with 128 zones, 8 areas, and a
host of integrated fire, access, verification, and input/output modules, all reported with the Contact I.D. formats. The
modular design establishes a logical solution for ease of expansion. Up to 32 modules can be added to expand the
capabilities of the Hills Reliance.
NZ Telepermit Notice
Warnings
The equipment should be installed by
qualified SERVICE PERSONNEL only
The equipment should only be operated with
an approved power adapter with insulated live pins
CAUTION – RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF BATTERIES ACCORDING TO THE INSTRUCTIONS.
CONTACT YOUR INSTALLER FOR REPLACEMENT BATTERIES.
When installed as directed, this product conforms to the standards set by
Standards Australia on behalf of the Australian Communications Authority (ACA)
N4131
Disclaimer
The content of this document has been prepared to the best of our knowledge, provided “as is” and is subject to change
without notice. Hills Industries does not guarantee technical accuracy beyond the date of publishing. For the latest
information please enquire about attending one of our Hills Reliance training courses.
Copyright Notice
This work is copyright Hills Industries 2009. Apart from any use as permitted under the Copyright Act 1968, no part may be
reproduced by any process, including photocopying, scanning or other means, without prior written permission from Hills
Industries. Creation of derivative work unless agreed to in writing by the copyright owner is forbidden.
Hills Reliance Control Panel
Installation Manual
Page
Warnings ...............................................................................................................................................................................1
Compliance Notices .............................................................................................................................................................2
Updated Features .................................................................................................................................................................3
Ordering Information............................................................................................................................................................4
Installation & Programming Flowchart...............................................................................................................................5
Board Installation .................................................................................................................................................................6
Control Panel Comparison ..................................................................................................................................................6
Hills Reliance 128 Wiring Diagram......................................................................................................................................7
Hills Reliance 128 Terminal Descriptions...........................................................................................................................8
Hills Reliance 12 Wiring Diagram........................................................................................................................................9
Hills Reliance 12 Terminal Descriptions........................................................................................................................... 10
Hills Reliance 8 Wiring Diagram........................................................................................................................................ 11
Hills Reliance 8 Terminal Descriptions............................................................................................................................. 12
Main Options.......................................................................................................................................................................13
Programming The LED Code Pads ................................................................................................................................... 15
1. Setting The LED Code Pad Starting Zone - Function [9] [2]............................................................................... 15
2. Setting The LED Code Pad Options - Function [9] [3]........................................................................................ 15
3. Setting The LED Code Pad Number And Area Options - Function [9] [4] .......................................................... 16
4. Set Elapsed Hours Since Last Auto Test - Function [9] [5] ................................................................................ 16
5. Set System Date - Function [9] [6] ..................................................................................................................... 16
6. Setting The System Clock - Function [9] [7] ....................................................................................................... 16
7. Service Menu - Function [2] ............................................................................................................................... 17
8. Changing User Codes - Function [5] .................................................................................................................. 17
9. Assigning User Code Authority Levels - Function [6] ......................................................................................... 18
10. Walk Test Mode - Function [] [Chime] ...........................................................................................................19
11. Call Back Download [] [9] [8] and Answer Call [] [9] [9] ..............................................................................19
Programming The Hills Reliance Control Panel .............................................................................................................. 20
Features, Segments and Options........................................................................................................................... 20
Navigating Program Mode ..................................................................................................................................... 20
Programming Data ................................................................................................................................................. 21
Loading Factory Defaults ....................................................................................................................................... 21
Enrolling Modules & Code Pads............................................................................................................................. 21
Programming Example Figure 1 - Numerical Data (Binary) ................................................................................... 22
Programming Example Figure 2 - Option Selection Data....................................................................................... 22
Programming Feature Descriptions.................................................................................................................................. 23
System Codes........................................................................................................................................................ 23
Dialer Options (Features 4 – 11) ............................................................................................................................ 24
Download Options (Features 12 – 15) ................................................................................................................... 26
Area 1 – Option and Report Selections.................................................................................................................. 27
Zones 1 – 8 Configuration ...................................................................................................................................... 29
Default Zone Configurations .................................................................................................................................. 29
Zones 9 – 16 Configuration .................................................................................................................................... 31
System Options new .............................................................................................................................................. 32
Siren / Communicator Attempt Counter ................................................................................................................. 35
Code Pad Sounder Control .................................................................................................................................... 35
System Timer Configuration................................................................................................................................... 35
Auxiliary Output 1 – 4 Configuration....................................................................................................................... 36
Auxiliary Output 1 – 4 Logic new............................................................................................................................ 37
Auxiliary Output Logic Selection new ..................................................................................................................... 38
Auxiliary Output Event Selection ............................................................................................................................ 38
Areas 2 – 8 Programming Options ......................................................................................................................... 40
Zones 17 – 48 Configuration .................................................................................................................................. 44
Configuration Groups 1 – 20 .................................................................................................................................. 45
Zones 49 – 128 Configuration new ........................................................................................................................ 51
Appendix 1: Reporting Zone Codes in Contact I.D.......................................................................................................... 55
Appendix 2: Reporting Fixed Codes in Contact I.D......................................................................................................... 56
Appendix 3: Expander Numbers for Reporting Expander Trouble ................................................................................ 57
Appendix 4: Troubleshooting System Problems............................................................................................................. 59
Installation Floor Plan ........................................................................................................................................................62
Program Planning Sheets.................................................................................................................................................. 63
© Hills Industries 2009
Page 1
Compliance Notices
Information to the Installer - Changes and modifications not expressly approved by Hills can void the user’s authority to
operate the equipment.
Australia & New Zealand Compliances
This equipment has been tested and found to compliant with the ACA A-Tick and (NZ) Telepermit standards. These limits
are designed to provide reasonable protection against interference in a residential installation.
Hills Reliance systems fitted with the 433 MHz wireless receiver module receives radio frequency energy from wireless
transmitters and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the wireless transmitter units or receiver module to reduce interference.
• Increase the separation between the transmitting units and receiver.
• Connect the affected equipment and the panel receiver to separate power outlets, on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
A 230-240VAC mains power outlet (GPO) with protective earthing connection must be provided within reach of the
supplied plug pack power lead and be easily accessible. Only licensed electrical workers should install new GPOs. GPO
installation must comply with AS/NZS 3000:2000 and national or state electrical regulations. Connect this product to a
compliant 611, Mode3 or switched 8P4C socket. A RJ11phone lead is required to connect this product to a compliant 611,
Mode3 or switched 8P4C socket. A compliant RJ11 lead is supplied with this product.
Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be
able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone
line in use. To do so, alarm dialing equipment must be connected to a ACA (Aust.) or Telepermit (NZ) compliant Mode-3
socket that is electrically in series and ahead of all other telecommunication equipment attached to the same telephone
line. In Australia, only ACA certified technicians are permitted to install or modify telephone sockets.
Security Installation License
Australia installers – In New South Wales and the ACT the installer must hold a Security Installer License to install this
product.
New Zealand – All people involved in the selling, installation and servicing of security equipment must hold a Security
Guards Licence. Refer to the NZ Government Justice Department for further updates.
Note: Other national/state regulations may also apply. Enquire at the place of purchase if specific installation regulations
demand the Hills Reliance control panel installation requires a licensed installation technician.
Automatic Dialing Devices (Australia and New Zealand)
This equipment shall not be set to make automatic calls to the ‘000’ (Aust) or the Telecom ‘111’ (NZ) Emergency Service.
Series Connected Equipment (Australia & New Zealand)
The equipment may be set up to carry out test calls at pre-determined times. Such test calls will interrupt any other calls
that may be set up on the line at the same time. The timing set for such test calls should be discussed with the installer.
The timing set for such test calls from this equipment may be subject to “drift”. If this proves to be inconvenient and your
calls are interrupted, then the problem of timing should be discussed with the equipment installer. The matter should
NOT be reported as a fault to your telephone service provider faults service.
Automatic Re-attempts to the Same Number (New Zealand only)
Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the equipment
associated with this device. The associated equipment shall be set to operate within the following limits for compliance
with Telecom’s specification:
(a) There shall be no more than 10 call attempts to the same number within any 30 minute period for any single
manual call initiation.
(b) The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the
beginning of the next attempt.
Automatic Call to Different Numbers (New Zealand only)
Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the equipment
associated with this device. In order to operate within the limits for compliance with Telecom Specifications, the
associated equipment shall be set to ensure that automatic calls to different numbers are spaced such that there is no
less than 5 seconds between the end of one attempt and the beginning of another.
Fault Clearance (New Zealand only)
In the event of any problem with this device, the telephone lead should be disconnected from the LINE connection at
the rear of the unit. The user is then to arrange with the supplier of the device to make necessary repairs. Should the
matter be reported to Telecom as a wiring fault and the fault is proven to this device, a call-out charge will be incurred.
© Hills Industries 2009
Page 2
Updated Features
There are new features on the Hills Reliance product, and some which have been changed from the previous version.
These have the text “new” next to the relevant sections in this manual. A summary of key updates is presented below.
Feature
Location
F5, 37, 38,
41, 44, 47,
50, 53, 56
F16, 39,
42, 45, 48,
51, 54, 57
F17, 40,
43, 46, 49,
52, 55, 58
Feature
Location
Description
Description
Account Codes – expanded for future use
F33
Auto Disarm Time – added
Area Options – added Late To Close, AutoArm in Partial, Disable Bypass For Force
Arm Zones
F36
Days of the Week for Auto-Arm – added
Retry Timer
Entry / Exit Timers – expanded for future use
F68, 70,
72, 74, 76,
78, 80, 82,
84, 86, 88,
90, 92, 94,
96, 98,
100, 102,
104, 106
Configuration Groups – added Zone
Activity Monitor, EOL Defeat, REX
event, DOTL and Forced Door events
F119 - 138
Zones 49-128 – added
F18, 20,
59, 61, 63,
65, 119,
121, 123,
125, 127,
129, 131,
133, 135,
137
Zone Configuration Group – added Group 0
for Zone Disabled
F22
System Options – added Two Wire Smoke,
Zone Inactivity Monitor, Steady/Evac Siren
F22
Disable hardwire zones req power cycle
F155
Days of the Week for Auto Disarm –
added
F25
System Timers – added Chime Option, Zone
Inactivity Monitor
F162
EOL Resistor Value Select – added
F27
Auxiliary Output – changed on Reliance 8
F28 - 31
Auxiliary Output Logic – enhanced
Sales & Distribution
For Service / Technical Support call
(02) 9717 5222 or 1800 252 213
SA
Torrensville:(08) 8150 9400
NSW
Granville: (02) 9897 7722
Rosebery: (02) 9698 9698
Chatswood: (02) 8467 1467
VIC
Rowville: (03) 9755 6922
Coburg: (03) 9383 2066
WA
Balcatta: (08) 9241 3100
ACT
Fyshwick: (02) 6280 9630
QLD
Bowen Hills: (07) 3252 5512
Molendinar: (07) 5597 7203
TAS
Derwent Park: (03) 6272 0211
Auckland
Penrose: (09) 525 8007
Christchurch
Sydenham: (03) 374 6277
© Hills Industries 2009
Page 3
Wellington
Lower Hutt: (04) 939 9355
Ordering Information
Hills Reliance System Modules & Equipment
Part #
Description
DAS Code
NX-8-v2-HILLS
Hills Reliance 128 Control Panel
S4133
NX-6-v2-HILLS
Hills Reliance 12 Control Panel
S4142
NX-4-v2-HILLS
Hills Reliance 8 Control Panel
S4697
NX-1508-HILLS
Vertex 8 Zone LED Code Pad
S4158
NX-1516-HILLS
Vertex 16 Zone LED Code Pad
S4157
NX-108-HILLS
8 Zone LED Code Pad
S4127
NX-116-HILLS
16 Zone LED Code Pad
S4132
NX-124-HILLS
24 Zone LED Code Pad
S4131
NX-148-HILLS
Alphanumeric LCD Code Pad
S4145
NX-1448-HILLS
Icon LCD Code Pad
S2284
VN01
VoiceNav Code Pad
S1794A
NX-216E
16 Zone Expander Module
S4387
NX-507E
7 Relay Expander Module
S4164
NX-508E
8 Output Expander Module
S4128
NX-408EI
8 Zone Wireless Expansion Module
S4135
NX-416EI
16 Zone Wireless Expansion Module
S4134
NX-448EI
48 Zone Wireless Expansion Module
S4136
NX-1248
EchoStream 48 Zone Wireless Receiver
S1429AA
NX-320E
Smart Power Supply and Bus Extender
S4137
NX-536E
DTMF Communicator Module (only for Reliance)
-
DTMF Monitor Module (for commissioning & testing)
S3079
NX-583
STU Interface
S4143
NX-584E
RS232 Serial Interface Automation
S4703
NX-586E
Direct Connect Lead
S4714
NX-588E
USB Flash Programming Lead
S1221A
60-707-43-EUR
ITI 2 Button Keyfob Transmitter
S5735
60-659-43-EUR
ITI 4 Button Keyfob Transmitter
S5753
60-705-43-ENG
ITI Pendant Panic Transmitter
S5744
DL900
NX/Hills Reliance Downloader Software
NX-1701E
Proximity Card Reader
S1845
NX-002
Metal Box Small (for Hills Reliance 8)
S4146
NX-003
Metal Box Large (for Hills Reliance 12 and 128)
S4700
© Hills Industries 2009
Page 4
S1204A
-
Installation & Programming Flowchart
Note – This diagram is a guide for basic system programming only.
Configuration depends upon customer requirements
Customer
Requirements
Plan & quote
installation p 62
Order modules and
hardware p 4
Install cabling
p7
Mount equipment
Program system
p 20
Planning Sheet
see p 63
Change Installer Code (1#) &
Duress Code (3#)
p 23
DAS order form/s
Customer
User Details p 63
Program Phone 1 (4#)
Account code (5#)
Report Format (6#) p 24
Program Phone 2 (7#)
& Phone 3 (8#)
if required p 25
ACA Cabler
Electrical Contractor
Security License
(NSW)
or other local
requirements
Program Event Reports (9#)
& No. Dial Attempts (10#)
p 25
via code pad (or DL900 software)
Default System
Programming
p 21
Set Phone Line Cut
Delay (11#) p 25
Program Area 1 Options (16#)
& Entry/Exit Time (17#) p 27
Program User
Codes (5)
p 17
Test user codes
Program System
Time (97)
p 16
Walk test sensors
( Chime) p 19
Test timers
(siren, entry, exit, etc)
(44)
Program System
Date (96)
p 16
For Multiple Area Systems
see F37-58 p 40-44
Program Zones 1-8 (18#)
& Area allocation (19#) p 29
Program Zones 9-16
(20#, 21#) p 31
Zones 17-48
(59# - 66#) p 44 -45
Program System Options
(22#) p 32
Test phone numbers
(Cent Stn. & mobiles)
(44)
Test battery back up
(44)
Train customer to use
system
Program Code Pad
No. & Areas (94)
p 16
Program Code Pad
Options (93)
p 15
Exit Program Mode
p 20
System Handover
© Hills Industries 2009
Page 5
Program Siren/
Communication Attempts
(23#) & Code Pad Sound
Options (24#) p 35
Program System Timers (25#)
p 35
Program Autotest Time &
Freq. (32#) p 39
Board Installation
The metal enclosure should be installed with the door opening from the top to bottom. It
should be installed away from damp areas (e.g. bathrooms, kitchens), away from sources of
heat, dust or interference (e.g. air conditioners, washing machines, dryers, refrigerators) and
away from external walls.
Inside the enclosure there are four slots for board insertion, two on the top and two on the
bottom of the enclosure. These allow the PC board to be positioned vertically as shown in the
diagram. When you slide the board between the grooves of the slots, make sure the terminal
strip is toward the front opening (toward you) to allow for the wire connections.
Inside the enclosure several 2-holed insertion points have been constructed. This allows for
either vertical or horizontal placement of the modules. Notice that each insertion point has
two sizes of holes - a larger hole and a smaller hole.
Diagram 1: The black plastic PCB guides are grooved on one edge where the PC board will
be seated. The end with the half-moon protrusion fits into the larger hole. The smaller hole is
for the screw.
Diagram 2: Place the first black plastic PCB guide in the top insertion point, grooved edge
downward. The half-moon protrusion will be in the large hole. It does not require force to
insert. Insert one of the provided screw into the smaller hole (from inside the enclosure) to
secure it in place. A screwdriver should reach through the notch that runs the length of the
guide to tighten the screw. The second PBC guide should be positioned opposite the first
(grooved edge up) and placed in the lower insertion point, using the same procedures
described above. Once mounted, screw it in securely.
Diagram 3: The PC Board should slide freely in the grooves of both guides.
Control Panel Comparison
R8
R12
R128
Independent number of zones
8
12
16
Expandable to a maximum number of zones
(a combination of hardwired and/or wireless)
8
16
128
Anti-tamper supervision of all zones (hardwired and wireless)
Yes
Yes
Yes
Full supervision of all expansion module and code pads
Yes
Yes
Yes
Individual areas/partitions
1
2
8
Total number of user PIN codes (4 digit)
8
40
99
Maximum number of code pads
* Max 8 VoiceNav code pads if using intercom features
8
16
24
Code pad tampers
Yes
Yes
Yes
Uni Arming (single button arming for full or partial mode)
Yes
Yes
Yes
Home mode/Partial mode arming
Yes
Yes
Yes
Automatic arming (and auto partial mode arming)
Yes
Yes
Yes
Re-exit feature
Yes
Yes
Yes
Real-time event history (maximum events)
185
185
185
Phone line monitor
Yes
Yes
Yes
Fire alarm verification
Yes
Yes
Yes
1
2
4
NX-1701EAU Keyless Door Entry (maximum modules)
© Hills Industries 2009
Page 6
Hills Reliance 128 Wiring Diagram
© Hills Industries 2009
Page 7
Hills Reliance 128 Terminal Descriptions
Terminal
EARTH
AC
Description
Earth / Ground.
To comply with ACA S009 & AS/NZS3000:2000. Connect to the 16.5V AC plug pack earth wire.
AC input. Connect a 16.5V, 25 VA, 40 VA or 50 VA approved transformer.
Built in siren driver, if used as a siren output (default), the speaker rating should be
15 Watt at 8 or 16 Ohm, or 30/40 Watt at 4, 8, or 16 Ohm, 250mA maximum load.
BELL + &
BELL -
If voltage output is selected in Feature 22 - Segment 2 - Option 1, this output becomes voltage
output, 12 VDC, 1 Amp maximum load.
Note: A 3.3K resistor may be required across the bell terminals when a 12 VDC siren is used.
If no resistor is used, you may experience voltage leakage into the siren that will cause these devices
to output a small signal.
KP DATA
Connect the to the KP data terminal on the code pads and the expanders (usually blue or green
wire). Maximum total wire run is 800 metres using 14/020 cable. These numbers are for one code
pad at the end of the wire. When connecting more than one code pad to the system bus wire, a
higher gauge wire will be required, or there will be a reduction in maximum wire distance. Maximum
32 devices.
KP COM
Connect to the Common terminal on the code pads and the expanders (usually the black wire).
KP POS
Connect to the Positive terminal on the code pads and the expanders (usually the red wire).
The KP POS and AUX PWR + terminals are limited to 1 Amp total current when added together.
SMOKE+
Smoke detector power 12VDC, 500mA maximum.
COM
Connect negative wire of powered devices such as motion detectors and smoke detectors.
AUX PWR+
Connect positive wire of all powered devices except smoke detectors and code pads.
This terminal and KP POS are limited to 1 Amp total current when added together.
ZONE 8
Connect to one side of zone 8 loop. Connect the other side to a COM terminal. Open or short causes
alarm. Zone 8 may be used for a two-wire smoke detector using a 680 E.O.L. resistor. See Feature
22.
COM
Common (-) terminal for zones 7 & 8. (See the wiring diagram for examples)
ZONE 7 ZONE 1
Connect to one side of zone loop. Connect the other side to a COM terminal. Open or short causes
alarm. Only zone 8 can be a two-wire smoke zone. (See the wiring diagram for examples)
AUX
RELAY
OUT 1-2
Relays one and two switch a 12 volts output on their N/C and N/O terminals. This means that you
connect the positive lead of your device to these terminals, and connect the negative lead to a COM
terminal. Ensure your device does not exceed the ratings of these relays, max 400 mA per output,
max 800 mA total output.
AUX
OUT 3-4
Auxiliary outputs 3 and 4 (in addition to 1 & 2) are located on a pin header J7, see wiring diagram for
details.
Battery
Leads
Connect black (-) and red (+) leads to a 12VDC sealed lead acid rechargeable battery.
Do not connect to a dry cell battery.
Warning: Total standby current drawn from SMOKE +, KP POS and AUX PWR +, must not exceed
700 mA with 16 VAC 3 Amp Plug Pack or 400 mA with 16 VAC 1.5 Amp Plug Pack.
© Hills Industries 2009
Page 8
Hills Reliance 12 Wiring Diagram
© Hills Industries 2009
Page 9
Hills Reliance 12 Terminal Descriptions
Terminal
EARTH
AC
Description
Earth / Ground.
To comply with ACA S009 & AS/NZS3000:2000. Connect to the 16.5V AC plug pack earth wire.
AC input. Connect a 16.5V, 25 VA, 40 VA or 50 VA approved transformer.
Built in siren driver, if used as a siren output (default), the speaker rating should be
15 Watt at 8 or 16 Ohm, or 30/40 Watt at 4, 8, or 16 Ohm, 250mA maximum load.
BELL + &
BELL -
If voltage output is selected in Feature 22 - Segment 2 - Option 1, this output becomes voltage
output, 12 VDC, 1 Amp maximum load.
Note: A 3.3K resistor may be required across the bell terminals when a 12 VDC siren is used.
If no resistor is used, you may experience voltage leakage into the siren that will cause these devices
to output a small signal.
KP DATA
Connect the to the KP data terminal on the code pads and the expanders (usually blue or green
wire). Maximum total wire run is 800 metres using 14/020 cable. These numbers are for one code
pad at the end of the wire. When connecting more than one code pad to the system bus wire, a
higher gauge wire will be required, or there will be a reduction in maximum wire distance. Maximum
16 devices.
KP COM
Connect to the Common terminal on the code pads and the expanders (usually the black wire).
KP POS
Connect to the Positive terminal on the code pads and the expanders (usually the red wire).
The KP POS and AUX PWR + terminals are limited to 1 Amp total current when added together.
COM
Connect negative wire of powered devices such as motion detectors and smoke detectors.
AUX PWR+
Connect positive wire of all powered devices except smoke detectors and code pads.
This terminal and KP POS are limited to 1 Amp total current when added together.
ZONE 6
Connect to one side of zone 6 loop. Connect the other side to a COM terminal. Open or short causes
alarm.
COM
ZONE 5 ZONE 1
Common (-) terminal for zones 5 & 6. (See the wiring diagram for examples)
Connect to one side of zone loop. Connect the other side to a COM terminal. Open or short causes
alarm. Only zone 7 can be a two-wire smoke zone. (See the wiring diagram for examples)
Aux 4 defaults to 12VDC smoke power for a four-wire smoke detector.
AUX
OUT 4
(or Zone 7
/Smoke +)
Alternatively this output can be programmed in Feature 22 as Zone 7 two-wire smoke detector. Use a
680 E.O.L. resistor with the two-wire smoke detector. Current is limited to 250mA when output is
negative and 250 microamps maximum when output is positive.
Note: The 2-wire smoke loop cannot be enabled if Zone Doubling is used.
AUX
OUT 1-3
Connect negative lead of low current device (e.g. relay, LED [install 1K resistor in series with LED],
etc). Connect positive lead of device to AUX PWR +. Current is limited to 250mA when output is
negative and 250 microamps maximum when output is positive.
Battery
Leads
Connect black (-) and red (+) leads to a 12VDC sealed lead acid rechargeable battery.
Do not connect to a dry cell battery.
Warning:
Total
standby
current
drawn
from
SMOKE
+,
KP
POS
and
AUX
must not exceed 700 mA with 16 VAC 3 Amp Plug Pack or 400 mA with 16 VAC 1.5 Amp Plug Pack.
© Hills Industries 2009
Page 10
PWR
+,
Hills Reliance 8 Wiring Diagram
© Hills Industries 2009
Page 11
Hills Reliance 8 Terminal Descriptions
Terminal
AC
Description
AC input. Connect a 16.5V 1.5A approved plug pack.
EARTH
Earth / Ground.
To comply with ACA S009 & AS/NZS3000:2000. Connect to the 16.5V AC plug pack earth wire.
AUX
OUT 1
Auxiliary Output Terminal, normally used to connect the negative lead of the strobe. The positive lead
of the strobe can be connected to any of the positive terminals e.g. KP POS. Current is limited to
250mA when output is negative and 250 microamps maximum when output is positive.
Built in siren driver, if used as a siren output (default), the speaker rating should be
15 Watt at 8 or 16 Ohm, or 30/40 Watt at 4, 8, or 16 Ohm, 250mA maximum load.
SIREN
If voltage output is selected in Feature 22 - Segment 2 - Option 1, this output becomes voltage
output, 12 VDC, 500mA maximum load.
Note: A 3.3K resistor may be required across the bell terminals when a 12 VDC siren is used.
If no resistor is used, you may experience voltage leakage into the siren that will cause these devices
to output a small signal.
COM
Common (-) Terminal
SMOKE+
Smoke detector power 12VDC, 100mA maximum.
At default output is 0V, to enable 12V set F27 - Seg 3 - Op 6 (invert output) to off. See Feature 27.
AUX
OUT 2
Auxiliary Output Terminal, normally used to connect the negative lead of the screamer. The positive
lead of the screamer can be connected to any of the positive terminals e.g. KP POS. Current is
limited to 250mA when output is negative and 250 microamps maximum when output is positive.
KP DATA
Connect the to the KP data terminal on the code pads and the expanders (usually blue or green
wire). Maximum total wire run is 800 metres using 14/020 cable. These numbers are for one code
pad at the end of the wire. When connecting more than one code pad to the system bus wire, a
higher gauge wire will be required, or there will be a reduction in maximum wire distance. Maximum 8
devices.
KP COM
Connect to the Common terminal on the code pads and the expanders (usually the black wire).
KP POS
Connect to the Positive terminal on the code pads and the expanders (usually the red wire).
The KP POS and AUX PWR + terminals are limited to 1 Amp total current when added together.
COM
ZONE 4
COM
ZONE 3 ZONE 1
Battery
Leads
Connect negative wire of powered devices such as motion detectors and smoke detectors.
Connect to one side of zone 4 loop. Connect the other side to a COM terminal. Open or short causes
alarm.
Common (-) terminal for zones 5 & 6. (See the wiring diagram for examples)
Connect to one side of zone loop. Connect the other side to a COM terminal. Open or short causes
alarm.
Connect black (-) and red (+) leads to a 12VDC sealed lead acid rechargeable battery.
Do not connect to a dry cell battery.
Warning: Total standby current drawn from SMOKE +, KP POS and AUX PWR +, must not exceed 700 mA with
16 VAC 3 Amp Plug Pack or 400 mA with 16 VAC 1.5 Amp Plug Pack.
© Hills Industries 2009
Page 12
Main Options
Areas
The Hills Reliance 128 can have up to a maximum of eight separate systems (areas) with distinct reporting codes,
user codes, and operating options for each system (see Features 16-21 and 37-58). The Hills Reliance 12 has up to
two areas, and the Hills Reliance 8 has one area.
Arm / Disarm Codes
The Hills Reliance 128 can have 99 four-digit codes or 66 six-digit codes to arm/disarm the control. All codes must
have the same number of digits. User codes are programmed and viewed from the code pad functions [*] 5 and [*] 6.
The factory default for user 1 is [1]-[2]-[3]-[4] when using a 4-digit code, or [1]-[2]-[3]-[4]-[5]-[6] for a 6-digit code.
This code can then be used to enter the new arm/disarm codes (see Feature 0). The Hills Reliance 12 can have up to
40 users, the Hills Reliance 8 up to 8 users.
Auto-Arm in Partial
The Hills Reliance can be armed automatically in the partial mode. This option can only be used for area one. If AutoArm in Partial is enabled, area one cannot have full mode Auto-Arming selected. (See Feature 22)
Automatic Arming
If programmed, the Hills Reliance will Auto-Arm at a specified time. At this time, the code pad will beep for 50
seconds before the panel arms. The auto-arming process can be stopped by a valid code entry during Exit Time.
The Auto-Arming of an area can be programmed to be silent. If closing reports are sent, the user code will be 97.
(See Features 16, and 33-36)
Auxiliary Outputs
The Hills Reliance 128 has two (2) programmable relay outputs and two (2) programmable open collector outputs that
can be used to activate a strobe and two internal sirens. (See the terminal description Features 26-29). The Hills
Reliance 12 has 4 programmable open collector outputs, and the Hills Reliance 8 has two.
Auxiliary Power Over Current
The Hills Reliance will illuminate the ‘Service’ LED on the code pad whenever too much current is drawn from any
device powered by the system. This condition can be reported to the central station. (See Features 9 and 22)
Box Tamper
The Hills Reliance has an input for a normally closed tamper switch (see wiring diagrams on p7, p9, p11). The Box
Tamper can be programmed to report and/or sound the siren and/or the Code Pad. These terminals can be enabled
or disabled in programming. (See Features 22 and 23)
Code Pad Start Zone
The Hills Reliance LED Code Pads can be programmed with a starting zone from 1 to 64. The starting zone
programmed into the LED Code Pad via function [*][9][2] will tie the system zone to zone one (1) of the Code Pad.
I.e. If you wish to start displaying zone 25 as the zone one (1) on a LED Code Pad, program a 25 as the start zone
into the Code Pad that will function in this manner. When system zone 25 is faulted, zone LED one (1) will illuminate
on the programmed Code Pads. Zone bypasses will be tied to the Code Pad LED number; however reporting will
follow the system zone number.
Configuration Group
The Hills Reliance has 20 programmable and 10 fixed zone configuration groups (i.e. zone types) that determine how
each zone will function and report. The first 20 groups can be reprogrammed.
Dual End of Line
All Hills Reliance zones can be enabled for tamper monitoring if the Dual End of Line option is enabled. Zone
Doubling cannot be used if the option is enabled. (See Feature 22)
Dynamic Battery Test
The Hills Reliance can be programmed to perform a dynamic battery test to verify the condition of the battery for a
selected duration the first time the panel is armed or disarmed every day. The Hills Reliance can also be programmed
to perform a missing battery test every 12 seconds. (See Features 22 and 25)
© Hills Industries 2009
Page 13
Exit Error
If enabled, the Hills Reliance will send an ‘Exit Error Report’ if an entry/exit zone is faulted at the instant the exit delay
expires. This report will be sent along with the user number that armed the system, if the panel is not disarmed
before the entry delay expires. The alarm report will also be sent. Even if this option is not enabled, the siren will
sound if any entry/exit zone is faulted at the instant the exit delay expires. (See Feature 9 and 16)
Expander Trouble
The Hills Reliance will report expander trouble to the central station if enabled. This condition will illuminate the
‘Service’ LED on the code pad even if not reported. Note: The code pads are considered expanders. The number of
the expansion devices reported can be found in Appendix 3. (See also Feature 9 and 22)
Fire Alarm Verification
When enabled, the Hills Reliance will verify a fire alarm by waiting for a second trip on a smoke detector within a
specified time before creating an alarm (see Feature 25). To interrupt the smoke detector power (when in the
disarmed state) each time the [*] 7 keys are pressed, the corresponding LED(s) for zones designated as ‘Fire’ must
be on steady for alarm or blinking for trouble. When the ‘Fire Alarm Verification’ option is enabled, a smoke detector
will be powered down and reset automatically after the first trip, waiting for a second trip within a specified time before
creating an alarm. The communicator will delay for a specified time before reporting the alarm, if a valid code is
entered, the report will be aborted, and the smoke alarm verification option will be reset if enabled. If no valid code is
entered the alarm report will be reported to the base station. (See Zone Configuration Group Table and Feature 25)
Group Bypass
A designated group of zones can be programmed to bypass by pressing [Bypass]-[0]-[0]-[Bypass] prior to arming.
(See Zone Configuration Group Table)
Internal Event Log
Up to 185 events can be stored in memory along with the date and time of the event. These events can later be
viewed through downloading or the LCD code pad. All reportable events report to the log.
Number of Calls and Rings to Answer
The Hills Reliance can count the number of calls and rings that must be met for automatic download answering.
(See Feature 13)
On Board Zone Disable
The zones on the main Hills Reliance control panel can be disabled in order to have a completely wireless alarm
system. (See Feature 22)
Partial Mode
Partial mode allows system owners to arm only designated partial zones (e.g. downstairs, front doors, garage),
bypassing all non-partial zones (e.g. upstairs bedroom). Partial mode encourages system owners to use their alarm
system more frequently when the premise is occupied. When armed in the ‘Partial’ mode, the opening of any zones
designated as ‘Partial Mode zone’ will initiate the code pad sounder and start the Partial Mode entry delay before
creating an alarm. All other zones will function as normal. (See Zone configuration Group Table and Features 16
and 25)
Siren Supervision
The Hills Reliance has a siren supervision circuit (Bell + and Bell -) that will constantly monitor the siren on the Hills
Reliance and can be programmed to report if the wires are cut. (See Feature 22)
Telephone Line Monitor
The Hills Reliance 128 and Hills Reliance 12 have a telephone line monitor that monitors the voltage and current of
the telephone line to detect a cut phone line. This condition can also be reported to the central station after the line is
restored. Not available on the Hills Reliance 8.
Twin Trip
This option requires two or more trips on a zone or zones programmed as ‘Twin Trip’ within a specified time before
reporting an alarm. During the time between trips, the Hills Reliance can be programmed to sound the code pad
and/or the siren. The Hills Reliance will also see an alarm activation if any Twin Trip zone that is continuously faulted
for longer than 10 seconds. (See Zone configuration Group Table and Features 22, 24, and 25)
© Hills Industries 2009
Page 14
Programming The LED Code Pads
This section describes how to program the address and area of each code pad as well as the options that are available.
The code pad address allows the panel to monitor and supervise the connected code pads and report code pad
communication faults.
The factory default for the Master code is [1]-[2]-[3]-[4] when using a 4-digit code or [1]-[2]-[3]-[4]-[5]-[6] for a 6-digit code.
The factory default for the ‘Go To Program’ code is [9]-[7]-[1]-[3] for a 4-digit code or [9]-[7]-[1]-[3]-[0]-[0] for a 6-digit code.
1. Setting The LED Code Pad Starting Zone - Function [9] [2]
Step 1
Your system must be in the Disarmed state to program the code pad settings
Step 2
Press the []-[9]-[2] keys
Step 3
Enter the [Program Code]
Enter the Starting zone number from 1 to 128.
Step 4
Note that older code pads only support up to 48 zones (i.e. non “E” versions”). Keep this in mind when
expanding a site by replacing the panel – some code pads may also need replacing. On sites with >48
zones it is recommended to use an LCD code pad.
Step 5
Press [] to save changes and exit this function
2. Setting The LED Code Pad Options - Function [9] [3]
Step 1
Your system must be in the disarmed state to program the code pad settings
Step 2
Press the []-[9]-[3] keys
Enter the [Program Code]. The ‘Service’ LED will flash
LEDs 1-8 can now be toggled on/off to enable/disable the functions listed in the table below:
LED
1
Enable Code Pad tamper switch
2
Enable Silent Code Pad option
3
Enable Ding Dong sound for Chime – If off, chime will be a single tone.
4
Enable Key-press Silence option (silences the pulsing code pad sounder for 5
seconds when a key is pressed)
5
Enable Armed Status Suppression (faulted or bypassed zones will not display
on code pad when system armed)
6
Enable Panic, Fire, Medical Beep-tone (will sound a short beep to verify that the
key-press was accepted)
7
Suppresses the ‘Service’ LED (will not allow the ‘Service’ LED to illuminate for
any reason. If there is a system trouble, pressing []-[2] will still show the service
menu.)
8
Enable multi-area viewing (enables temporary viewing of all areas by pressing
[]-[1]-[Area Number])
Step 3
Step 4
Code Pad Option Enabled
After enabling/disabling the desired functions press [] to save changes and exit this function.
© Hills Industries 2009
Page 15
3. Setting The LED Code Pad Number And Area Options - Function [9] [4]
Step 1
Your system must be in the disarmed state to program the code pad settings
Step 2
Press the []-[9]-[4] key
Step 3
Enter the [Program Code] – The ‘Service’ LED will flash
Step 4
Enter the code pad number [1-8]
Step 5
Press [] - The ‘Instant’ LED will illuminate steady and the ‘Service’ LED will remain flashing
Step 6
Enter the [Area Number] for the code pad (the code pad will automatically exit this mode at this time)
4. Set Elapsed Hours Since Last Auto Test - Function [9] [5]
Step 1
Your system must be in the disarmed state to program the code pad settings
Step 2
Press the []-[9]-[5] keys
Step 3
Enter the [Program Code] – The ‘Service’ LED will flash
Enter [100's digit] - [10's digit] - [1's digit] for the elapsed hours
Step 4
Step 5
Example: if you have programmed the Auto-Test intervals to report every 72 hours, the value in this
function will determine the first time the auto test report is made, so to have the first test occur in 12
hours and then every 72 hours, simply subtract the 12 from 72 which gives you a value of 60 hours. The
value in this function would be [6][0].
Press the [#] key to exit this function
5. Set System Date - Function [9] [6]
Step 1
Press the []-[9]-[6] keys
Step 2
Enter the [Master Code]
Step 3
Enter the ‘Day of Week Code’:
1 = Sunday
3 = Tuesday
2 = Monday
4 = Wednesday
Step 4
Enter the ‘Month Code’ – this must be two (2) digits:
01 = January
05 = May
09 = September
02 = February
06 = June
10 = October
03 = March
07 = July
11 = November
04 = April
08 = August
12 = December
Step 5
Enter the ‘Day Code’ – this must always be two (2) digits.
Example: The 5th would be entered as [0][5]
Step 6
Enter the last two digits of the ‘Year Code’. Example: For 2006 enter [0][6].
5 = Thursday
6 = Friday
7 = Saturday
6. Setting The System Clock - Function [9] [7]
Step 1
Press the []-[9]-[7] keys.
Step 2
Enter the [Master Code]
Step 3
Enter the ‘Hour Code’, which must be two (2) digits. Note: The clock is a 24-hour clock.
Example: Enter 12:00 am as [0]-[0], 7.00 AM as [0]-[7], and 5:00 PM as [1]-[7].
Step 4
Enter the ‘Minutes Code’, which must be two (2) digits.
Example: 7 minutes after the hour would be entered [0] [7].
© Hills Industries 2009
Page 16
7. Service Menu - Function [2]
The service light will be “on” if the security system requires service. If the service LED is “on”, press the [] key followed by
the [2] key to determine the service condition. One or more zone LEDs will illuminate indicating what service(s) is required.
Call your service provider immediately for these problems. Below is a listing of what each LED means in a service
condition:
LED
Problem
SYSTEM FAULT – Press the [1] key. The zone LED(s) illuminated corresponds to the system fault(s)
below:
LED
1
System Fault
LED
System Fault
1
Over Current Fault
5
Expander Low Battery
2
Siren Trouble
6
Expander Box Tamper
3
Box Tamper
7
Expander Trouble
4
Expander Power
8
Reserved
Note: Faults 1 & 2 are global in nature and will affect all areas of a multi-area system.
Press the [#] key to return to the 1 of 8 service LEDs.
2
ZONE TAMPER – Press the [2] key and the zone LED(s) will illuminate showing the zone(s) that are
tampered. Press the [#] key to return to the 1 of 8 service LEDs.
3
ZONE LOW BATTERY – Press the [3] key. The zone LED(s) will illuminate showing which zone(s) has a
low battery. This only applies to wireless zones. Press the [#] key to return to the 1 of 8 service LEDs.
4
ZONE LOSS OF SUPERVISION – Press the [4] key and the zone LED(s) will illuminate showing which
zone(s) has loss of supervision. This only applies to wireless zones. Press [#] key to return to the 1 of 8
service LEDs.
5
ZONE TROUBLE – Press the [5] key and the zone LED(s) will illuminate showing which zone(s) has a
trouble condition. Press the [#] key to return to the 1 of 8 service LEDs.
6
TELEPHONE LINE TROUBLE/LINE CUT – This light will illuminate when the panel senses loss of phone
line.
7
FAILURE TO COMMUNICATE – This LED illuminates when there is a failure to communicate between
your system and the central station. Note: This fault is global in nature affecting all areas of a multi-area
system.
8
LOSS OF SYSTEM TIME – This LED illuminates when there has been a loss of power and your system
clock needs to be reset. See steps 5 and 6 above to program system date and time.
To exit the Service LED Mode - press the [#] key.
8. Changing User Codes - Function [5]
Step 1
Your system must be in the disarmed state to change user codes.
Step 2
Press the []-[5] keys
Step 3
Enter a [Master Arm/Disarm Code]
Note: Multi area systems: A user changing another user’s code must have access to all or more areas
than the user being changed.
Step 4
The ready light will flash
Step 5
Enter the 2 digit ‘user number’ (always enter 2 digit such as [0]-[3] for user 3)
Step 6
Enter the new four (4) or six (6) digit ‘user code’.
Note: To delete a user code, enter [Chime]-[Chime]-[Chime]-[Chime] for a 4-digit code,
or [Chime]-[Chime]-[Chime]-[Chime]-[Chime]-[Chime] for a 6-digit code.
Step 7
The ready light will flash indicating you are back at Step 5 above. If the code is rejected, the sounder
beeps 3 times.
Step 8
If another ‘user code’ needs to be programmed, return to Step 5
Step 9
Press the [#] key while the ready light is flashing to exit the user code programming mode.
© Hills Industries 2009
Page 17
9. Assigning User Code Authority Levels - Function [6]
Step 1
Assign user codes before assigning authority levels
Step 2
Press the []-[6] key
Step 3
Enter a [Master Arm/Disarm Code]
Note: a user changing the authority of another user can only add or remove area authorization for areas
to which they have access.
Step 4
The ready light will flash
Step 5
Enter the 2 digit ‘user number’ to be assigned authority.
(The ready light is constant and the partial light will flash).
Lights illuminated indicate the authority levels assigned to this code. You may toggle (turn on/off) the
authority level by pressing the number for that authority level. An explanation of the lights is listed below:
LED Attributes if LED 8 is off
Step 6
LED Attributes if LED 8 is on
1
Reserved
1
Activate output 1
2
Arm Only
2
Activate output 2
3
Arm Only After Close Window
3
Activate output 3
4
Master arm/disarm (can program
other codes)
4
Activate output 4
5
Arm/disarm code
5
Arm/disarm
6
Allowed to bypass zones (see F23)
6
Bypass zones
7
Code will send open / close reports
7
Open / Close reporting
If LED 8 is off, LEDs 1-7 will use the
If LED 8 is on, LEDs 1-7 will use the
8
details in this column
details in this column
Note you cannot set attributes on both sides of the table above (e.g. Arm Only and Activate output 3).
8
Step 7
Press the [] key. The ready light will flash. This moves you to the area enable.
(The user has access to areas that are illuminated by the LEDs.)
The illuminated numbers indicate each area where the user has access. To change any of the areas
where the user has access, press numbers corresponding to areas where you want to give the user
access or deny access. Refer to chart shown below:
Step 8
LED
Areas Assigned
LED
Areas Assigned
1
Area 1
5
Area 5
2
Area 2
6
Area 6
3
Area 3
7
Area 7
4
Area 4
8
Area 8
Example: If zone LED 2 is lit, then the user is assigned access to area 2. By pressing the [2] key, the
light will go off, denying access to area 2.
Step 9
When the areas are assigned, press the [] key, returning you to Step 4. You may then enter another
user number to assign authority level. Repeat Steps 4 - 8 until you have assigned authority levels to all
user numbers.
Step 10
Press the [#] key to exit the Assigning Authority Level Program.
Note: Any master arm/disarm code can add or change a user code if the master code has access to the same areas as the
code being added/changed. Consequently, when programming the user codes for such a system, leave at least one code
(can be ‘Go To Program Code’ if enabled in Feature 2) access to all areas or you will not be able to add new users. If you
desire the end user to be able to add new codes, you must remove the area authority from all blank codes.
© Hills Industries 2009
Page 18
10. Walk Test Mode - Function [] [Chime]
Step 1
Press the []-[Chime] keys
Enter a [Master Arm/Disarm Code]
Step 2
Now all zones become 24 hour, silent and local (non reporting zones). By faulting any zone, that zone will
latch its zone light on the LED code pad, and sound the Chime. The Chime will continue to sound each
time a zone is faulted. Once all zone are tested (zone lights lit on the LED code pad) go to step 3.
Step 3
Enter a [Master Arm/Disarm Code]
11. Call Back Download [] [9] [8] and Answer Call [] [9] [9]
Pressing []-[9]-[8] while the system is disarmed will cause the control panel to initiate a call back for a
download connection (remote access). Note: a valid user code may be required after []-[9]-[8] if
enabled in Feature 0.
Step 1
Pressing []-[9]-[9] while the system is disarmed will cause the control panel to seize the phone line for
a download connection (remote access). Note: a valid user code may be required after []-[9]-[9] if
enabled in Feature 0.
© Hills Industries 2009
Page 19
Programming The Hills Reliance Control Panel
Features, Segments and Options
The Hills Reliance programming structure consists of Features, Segments, and Options.
Features or Feature numbers are used to locate an option or group of options.
Example: Feature 6 contains the communicator format selection and Feature 16 contains area one options.
Segments are contained within each feature, there are two types of segments.
The first segment type is referred to as an option select segment. This segment type contains up to eight options that can
be toggled On or Off like dip switches.
The second segment type is referred to as a numeric segment. This segment type requires a value from ‘0’ to ‘255’ to be
entered.
Options are contained within segments. An option select segment can have up to eight options. A numeric segment can
have a value of ‘0’ to ‘255’.
Example: Feature 6 contains the communicator format that has one segment with one option; and Feature 16 contains area
one options that has 5 segments with 40 options in total.
Navigating Program Mode
Entering The Program Mode: To enter the program Mode, press []-[8]. At this time, the five function LEDs (On, Partial,
Exit, Bypass, & Chime) will begin to flash. Next, enter the ‘Go To Program Code’ (factory default is [9]-[7]-[1]-[3]). If the ‘Go
To Program Code’ is valid, the ‘Service’ LED will flash and the five function LEDs will illuminate steady. You are now in the
Program Mode and ready to select the module to program.
Selecting The Module To Program: Since all modules connected to the Hills Reliance are programmed through the code
pad, the module you are programming should be the first entry. To program the Hills Reliance control panel, enter [0]-[#].
[0] is the module number of the control and the [#] is the enter key. Other module entry numbers can be found in their
corresponding manuals.
Programming A Feature: Once the number of the module to be programmed has been entered, the ‘Armed’ LED will
illuminate, indicating it is waiting for a programming feature to be entered. Any feature can be accessed by directly entering
the desired programming feature followed by the hash [#] key. If the feature entered is a valid feature, the ‘Armed’ LED will
extinguish, the ‘Ready’ LED will illuminate and the binary data for the first segment of this feature will be shown by the zone
LED's. While entering new data, the ‘Ready’ LED will begin flashing to indicate a data change in process. The flashing will
continue until the new data is stored by pressing the [] key. Upon pressing the [] key, the code pad will advance to the
next segment and display its data. This procedure is repeated until the last segment is reached. Pressing the [#] key will
exit from this feature, and the ‘Armed’ LED will illuminate again waiting for a new programming feature to be entered. If the
desired feature is the next sequential feature, press the [POLICE] key. If the previous feature is desired press the [FIRE]
key. If the same feature is desired press the [MEDICAL] key. To review the data in a feature, repeat the above procedure,
pressing the [#] key without any numeric data entry. Each time the [] key is pressed, the programming data of the next
segment will be displayed for review.
Exiting A Feature: After the last segment of a feature is programmed, pressing the [] key will exit that feature, turn the
‘Ready’ LED off and the ‘Armed’ LED on. You are now ready to enter another programming feature as before. If an attempt
is made to program an invalid entry for a particular segment, the code pad sounder will emit a triple error beep (beep, beep,
beep), and remain in that segment awaiting a valid entry.
Exiting The Program Mode: When all the desired changes in programming have been made, it is time to exit the program
mode. Pressing the [Exit] key will exit this programming level, and go to the ‘Select a Module to Program’ level. If no
additional modules are to be programmed, pressing the [Exit] key again will exit the program mode. If there is a module to
be programmed, it may be selected by entering its address followed by the [#] key (see ‘Selecting the Module To Program’
above). The procedure for programming these devices is the same as for the control panel, except the features will be for
the module selected.
© Hills Industries 2009
Page 20
Programming Data
Programming Data: Programming data is always one of two types. One type of data is numerical and can take on values
from 0-15 or 0-255 depending on the feature's segment. The other type of data is a Option selection type. Option selection
data is used to turn options on or off. Use the following procedures when working with these two data types:
Numerical Data: Numerical data is programmed by entering a number from 0-255 on the numeric keys of the system code
pad. To view the data in a feature, a binary process is used. With this process, the LED’s for zones 1 through 8 are
utilized, and the numeric equivalents of their illuminated LED’s are added together to determine the data in a programming
feature. The numeric equivalents of these LED’s are as follows:
Zone 1 LED = 1
Zone 5 LED = 16
Zone 2 LED = 2
Zone 6 LED = 32
Zone 3 LED = 4
Zone 7 LED = 64
Zone 4 LED = 8
Zone 8 LED = 128
Example: If the numerical data to be programmed in a feature is ‘66’, press [6]-[6] on the code pad. The LED’s for zone 2
and Zone 7 will become illuminated indicating 66 is in that feature (2 + 64 = 66). See this example on page 22.
Once the data is programmed, press the [] key to enter the data and advance to the next segment of that feature. After
the last segment of a feature is programmed, pressing the [] key will exit that feature, turn the ‘Ready’ LED off and the
‘Armed’ LED on. As before, you are now ready to enter another programming feature. If an attempt is made to program a
number too large for a particular segment, the code pad sounder will emit a triple beep, indicating an error, and remain in
that segment awaiting a valid entry.
Option Selection Data: Option selection data will display the current condition (on or off) of eight options associated with
the programming feature and segment selected. Pressing a button on the touch-pad (1 thru 8) that corresponds to the
‘option number’ within a segment, will toggle (on/off) that option. Pressing any numeric key between [1] and [8] for selection
of a option, will make the corresponding LED illuminate (option ON). Press the number again and the LED will extinguish
(option OFF). You will see that numerous options can be selected from within one segment. For instance, if all eight
options of a segment are desired, pressing [1]-[2]-[3]-[4]-[5]-[6]-[7]-[8] will turn on LED's 1 thru 8 as you press the keys,
indicating that those options are enabled. After the desired setting of options is selected for this segment, press the [] key.
This will enter the data and automatically advance to the next segment of the feature. When you are in the last segment of a
feature and press the [] to enter the data, you will exit that feature. This will now turn the ‘Ready’ LED off and the ‘Armed’
LED on. As before, you are now ready to enter another programming feature.
Loading Factory Defaults
There are two methods of loading the factory defaults:
Method 1 - Enter the program mode using the procedure on page 9, then type [9]-[1]-[0]-[#]. The code pad will beep 3
times indicating that the loading is in progress. The loading takes about 6 seconds.
Method 2 - Enter [9]-[7]-[1]-[3]-[0]-[0] within 10 seconds of power up at any code pad which is not programmed for
master mode. The procedure will default the Hills Reliance control panel even if it is armed.
Enrolling Modules & Code Pads
For supervision purposes, the Hills Reliance has the ability to automatically find and store in its memory, the presence of all
code pads, zone expanders, wireless receivers, and any other module connected to the data terminal (KP DATA) whenever
exiting the program mode. The enrolling process takes about 12 seconds, during which time the ‘Service’ LED will
illuminate. Once a module is enrolled, if it is not detected by the control panel, the ‘Service’ LED will illuminate on that code
pad.
To force module and keypad enrolment, whilst in program mode enter [9]-[1]-[5]-[#]-[Exit]-[Exit], and wait 12 seconds.
© Hills Industries 2009
Page 21
Programming Example Figure 1 - Numerical Data (Binary)
1
2
4
7
Zone 1 LED = 1
Zone 4 LED = 8
}
Zone 2 LED = 2
Zone 7 LED = 64
Data = 9
}
Data = 66
Enters the previous
programming “feature”
To change data in a segment,
enter the data followed by []
Returns to the “feature”
just programmed.
Pressing [#] will exit a feature
without changing the data in
the current segment
Advances to the next
programming “feature”
Programming Example Figure 2 - Option Selection Data
Feature 16 - Segment 1
1
5
7
LEDs show Options enabled
1 = Quick Arm
2 = Re-Exit
3 = Force Arm
4 = Silent Code Pad Panic
5 = Audible Code Pad Panic
6 = Code Pad Fire
7 = Code Pad Medical
8 = Code Pad Multiple
9 = Code Attempt Tamper
Press the key on the numeric Code Pad that corresponds
to the option you wish to enable/disable. When an LED is
“on”, an option is enabled; when “off” the option is
disabled. For example: With the 1, 5, & 7 LEDs “on”,
Quick Arm, Audible Code Pad Panic and Code Pad
Medical are enabled.
© Hills Industries 2009
Page 22
Programming Feature Descriptions
System Codes
Feature 0
Code Requirements
Feature 0, segment 1 is used to enable the 6 digit user code option. If 6-digit option is enabled, all arm/disarm codes, the
‘Go To Program Code’ and duress code are 6 digits. If this option is enabled, the default user 1 code is [1]-[2]-[3]-[4]-[5][6]. The Hills Reliance 128 has 99 four (4) digit user codes or 66 six (6) digit user codes, the Hills Reliance 12 has 40
codes, the Hills Reliance 8 has 8 codes. Segment 2 is used to enable user code requirement for functions []-[9]-[8]
(perform call back download) and []-[9]-[9] (answer incoming call for download).
Segment 1
1
On enables the 6-digit code option. Its original off state is a 4-digit code.
2
On requires code entry for []-[9]-[8] and []-[9]-[9] functions
3 –8
Reserved
Feature 1
Go to Program Code
Segments 1-6
9
7
1
3
0
0
Feature 1 contains the ‘Go To Program Code’. This feature contains either a 4 or 6-digit code. If the 6-digit code option is
enabled in Feature 0, this code must contain six (6) digits. If this option is not enabled in Feature 0, the last 2 segments
(digits) will be ignored. With the panel disarmed, the ‘Go To Program Code’ can be used to enter the program mode.
Feature 2
Go To Program Code Area and Authorisation
The ‘Go To Program Code’ can be used as a standard arm/disarm code. When using the code to arm or disarm, the user
I.D. is 255. (This code may not be changed in the run mode.)
Segment 1
1
Reserved
2
On enables ‘Go To Program Code’ as an arm only code
3
On enables ‘Go To Program Code’ as an arm only after closing
(4)
On enables ‘Go To Program Code’ as a master code (can change user codes)
5
On enables ‘Go To Program Code’ as an arm/disarm code
6
On enables ‘Go To Program Code’ to bypass zones
7
On enables ‘Go To Program Code’ opening and closing reports
8
Reserved
Segment 2
(1)
On enables the ‘Go To Program Code’ for area #1
(2)
On enables the ‘Go To Program Code’ for area #2
(3)
On enables the ‘Go To Program Code’ for area #3
(4)
On enables the ‘Go To Program Code’ for area #4
(5)
On enables the ‘Go To Program Code’ for area #5
(6)
On enables the ‘Go To Program Code’ for area #6
(7)
On enables the ‘Go To Program Code’ for area #7
(8)
On enables the ‘Go To Program Code’ for area #8
Feature 3
Segments 1-6
Duress Code
15
15
15
15
15
15
Feature 3 contains the ‘Duress’ code. This feature contains either 4 or 6 digits. If the 6-digit code option is enabled in
Feature 0, This code must contain six (6) digits. If the 6-digit option is not enabled in Feature 0, the last 2 digits will be
ignored. If the duress code is programmed, it will work for all areas.
© Hills Industries 2009
Page 23
Dialer Options (Features 4 – 11)
Feature 4
Phone Number One (1)
Segments 1-20
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
The first telephone number is programmed in Feature 4.
’15’ = pulse dialling - in the segment where pulse dialling should begin
’14’ indicates the end of the phone number. Fill all empty segments after end of dialling with ‘14’
’13’ = four second delay - in the segment where a delay is required
’12’ = a ‘#’ - in the segment as required
‘11’ = for a ‘’ - in the segment as required
Feature 5 new
System Account Code
Segments 1-6
10
10
10
10
Reserved new
Reserved new
This is the account code sent for any area event (open/close and zone related alarms) that does not have its account code
programmed. System events (siren/box tampers, expander troubles, etc.) will use the system account unless area one
account is programmed.
Feature 6
Communicator Format
Segment 1
0
Feature 6 contains the communicator format used. Select a format from the format selection table. If this feature contains a
‘0’, the built-in communicator will be disabled, and the panel will function as a local only control.
Data
Communicator Format
0
Local
Communicator is disabled
1
Contact I.D.
DTMF format for control rooms
2
Pager
Reports in 4 + 2 DTMF format. Phone numbers can be programmed via code pad in normal
operation.
3
Domestic Siren
Domestic dialling via a siren tone format. Call can be kissed off via the star () key on a DTMF
phone. Phone numbers can be programmed via code pad in the run mode.
Feature 7
Segments 1-20
Phone Number Two (2)
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
The second telephone number is programmed in Feature 7.
’15’ = pulse dialling - in the segment where pulse dialling should begin
’14’ indicates the end of the phone number. Fill all empty segments after end of dialling with ‘14’
’13’ = four second delay - in the segment where a delay is required
’12’ = a ‘#’ - in the segment as required
‘11’ = for a ‘’ - in the segment as required
© Hills Industries 2009
Page 24
14
14
14
14
Feature 8
Segments 1-20
Phone Number Three (3)
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
The third telephone number is programmed in Feature 8.
’15’ = pulse dialling - in the segment where pulse dialling should begin
’14’ indicates the end of the phone number. Fill all empty segments after end of dialling with ‘14’
’13’ = four second delay - in the segment where a delay is required
’12’ = a ‘#’ - in the segment as required
‘11’ = for a ‘’ - in the segment as required
Feature 9
Event Report Summary
Feature 9 is a summary of event reporting codes found in the area and system features. Area report events are enabled in
area options, but will also need to be enabled in this feature. This approach is used to simplify event selection
programming.
Segment 1
(1)
Alarms
(2)
Alarm Restores
3
(4)
5
(6)
7
(8)
Opening / Closing (alarm system disarmed = open, alarm system armed = close)
Bypass and Bypass Restore
Zone Trouble and Restore
Power Trouble (AC Failure or Low Battery) and Restore
Tampers and Restore (Zone, Box, Code Pad and also for Zone Activity Monitor)
Test Reports
Segment 2
(1)
System Trouble (siren / phone / expander / short circuit) and Restore
(2)
Failure to Communicate
(3)
Sensor Lost / Sensor Low Battery
4
(5)
Program, Download, & Full Log (Full Log must also be enabled in system options)
Cancel Code (Cancel reporting must also be enabled in area options)
6
Recent Closing / Exit Error
7
Reserved
8
Reserved
Feature 10
Segments 1-2
Dial Attempts and Dialing Options
6
0
Feature 10, Segment 1 is used to enter the number of dial attempts (1 to 15 attempts) the communicator will make to phone
#1 before ending the notification process. Factory default is ‘6’ and the communicator will make 6 attempts to the first
number.
Feature 10, Segment 2 configures additional functionality. Factory default is “0” – no function.
A value of “1” enables Dual Reports – sends reports to both phone number 1 & 2.
A value of “4” enables extended phone number and joins Feature 4 & 7 together for a 40 digit phone number.
Feature 11
Phone Line Cut Delay
Segment 1
0
Feature 11 contains the number of second increments in the telephone line monitor delay before phone line fault is
activated. The telephone line monitor delay can be programmed in 1 second increments from 1 to 255 seconds.
Note: The Hills Reliance 128 and 12 internal phone line monitoring circuit requires approximately 5 seconds to discharge
before it senses a missing phone line, you must add this time to the value in this feature when testing this option. A value of
“0” = disabled.
© Hills Industries 2009
Page 25
Download Options (Features 12 – 15)
Feature 12
Download Access Code
Segments 1-8
1
6
0
0
0
0
0
0
Feature 12 contains the eight digit access code the panel must receive from the downloading software before the panel will
permit downloading to occur.
Feature 13
Number of Rings (Seg 1) / Number of Calls to Answer (Seg 2)
Segments 1-2
0
0
Feature 13, segment 1 contains the number of rings the panel must detect before answering the telephone line when
initiating a download session. A value of 1 to 15 can be entered in this segment. Segment 2 contains the number of calls
the panel must detect before accepting the number of rings in segment 1. A value of 1 to 15 can be entered in this segment.
A call is satisfied by one (1) or more rings, and then an eight (8) second period of no ringing. The next call must then be
made within 45 seconds. The total number of calls must be reached before the panel will count for the number of rings (in
segment 1) during the necessary subsequent call. A value of “0” = disabled.
Feature 14
Download Control
Feature 14 contains the option selections for the controlling of download sessions. The following options can be enabled or
disabled using this feature.
Segment 1
1
On enables two call Answering Machine Defeat (see page 28 for a full explanation of this option).
2
Reserved
3
On enables Call Back Before Download Session (see Feature 15).
On enables Control Panel Shutdown
(Can only be viewed from the code pad, must be changed through downloading).
On locks all local programming
(Can only be viewed from the code pad, must be changed through downloading).
On locks programming of all features associated with the communicator
(Can only be viewed from the code pad, must be changed through downloading).
On locks out download section. (If ‘On’, Features 12-15 cannot be viewed from the code pad)
Note: This segment can only be changed through the download software.
On enables Call Back at Auto Test Interval to perform download software automatic functions
(Refer to your download software help for a full explanation of this option).
4
5
6
7
8
Feature 15
Segments 1-20
Call Back Number
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
If a telephone number is programmed into this feature, and “Call Back Before Download Session” is enabled in Feature 14,
the control panel will hang up for approximately 10 seconds and then call back. If pulse dialling is desired, program a ‘15’ in
the segment where pulse dialling should begin. If the entire number should be pulse dialling, program a ‘15’ in the first
segment. Four-second delays can be obtained anywhere in the sequence by programming a ‘13’ in the appropriate delay
feature.
Warning: the call back phone number should always be reviewed for accuracy before disconnecting!
© Hills Industries 2009
Page 26
Feature 16 new
Area 1 – Option and Report Selections
Feature 16 is used to enable certain options for this area and code pads in this area. In addition, certain communicator
reports are enabled in Feature 16. Each of these options can be enabled by area. For additional area information see
Features 37-58 on pages 40-44. If the option selection feature for any area is left blank, that area will use this feature
for the option selection. This feature contains 5 segments of 8 options each.
Segment 1
(1)
On enables the Quick Arm option
(2)
On enables the Re-exit option
3
On enables the Force Arm option
4
On enables the Silent Code Pad Panic option
(5)
On enables the Audible Code Pad Panic option
(6)
On enables the Code Pad Fire option
(7)
On enables the Code Pad Medical option
8
On enables the Code Pad Multiple Code Attempt Tamper option
Segment 2
1
On enables the LED Extinguish option
2
On enables the Require Code for Bypassing option
3
On enables the Zone Bypassed Sounder Alert option
(4)
On enables the AC Power/Low Battery Sounder Alert option
(5)
On enables Bypass toggle
6
On enables Silent Auto-Arm
7
On enables the Universal Arming option
8
On enables the One Key Partial Mode Disarm
Segment 3
(1)
On enables Opening and Closing reports
(2)
On enables Zone Bypass reporting
(3)
On enables Zone Restore reporting
(4)
On enables Zone Trouble reporting
(5)
On enables Zone Tamper reporting
6
On enables the Cancel reporting
(7)
On enables Recent Closing reporting
(8)
On enables Exit Error reporting
Segment 4 new
1 new
On enables Late To Close reporting (requires Feature 6 to be set to Contact ID)
2 new
On enables Auto-Arm In Partial
3 new
Reserved
4 new
On enables Disable Bypass For Force Arm Zones
5 new
Reserved
6 new
Reserved
7 new
Reserved
8 new
Reserved
Segment 5 new
1 new
Reserved
2 new
Reserved
3 new
Reserved
4 new
Reserved
5 new
Reserved
6 new
Reserved
7 new
Reserved
8 new
Reserved
© Hills Industries 2009
Page 27
Area Option Descriptions
AC Power / Low Battery Sounder Alert
If enabled, the panel will beep the Code Pad sounder upon arming or disarming if the AC power is missing or a low battery
has been detected.
Answering Machine Defeat
If enabled, the DL900 software calling the panel will ring (briefly), hang up and ring (briefly) again. The sequence will be
repeated as many times as programmed in Feature 13. Answering machines usually answer calls after a long ring period.
The Answering Machine Defeat feature prevents the answering machine from answering the call from the DL900 software.
Bypass Code
If enabled, the panel will require a valid user code to be entered during the zone bypass function.
Cancel
If enabled, the panel will send a ‘Cancel’ report when the system is disarmed by a valid user after an alarm activation. The
cancel code followed by the user number.
Code Pad Activated Panics
The panel has three Code Pad activated panics that will send reports to the central station: Fire, Medical, and Code Pad
Panic. The Fire key will activate the steady (Fire) siren, the Medical key will sound the Code Pad (the Medical key can be
set for silent activation in system options), and the Code Pad Panic can be programmed to be silent or audible (sound
siren).
Code Pad Tamper
If enabled, the panel will disable the Code Pad for 60 seconds and communicate a tamper signal to the central station if 30
key-presses are entered without producing a valid code. The Code Pad sounder will remain functional.
Exit Error
If enabled, the panel will send an ‘Exit Error Report’ if an entry/exit zone is faulted at the instant the exit delay expires. This
report will be sent along with the user number that armed the system, if the panel is not disarmed before the entry delay
expires. The alarm report will also be sent. Even if this option is not enabled, the siren will sound if any entry/exit zone is
faulted at the instant the entry delay expires. This option is enabled by default, but needs to be set to report in Feature 9 for
proper operation.
Force Arming
When enabled, the panel can be Force Armed with zones faulted. Under this condition, if a force arm zone is not secure,
the ‘Ready’ LED will flash. At the end of the exit delay, these zones will become bypassed. If these zones become secured
any time during the arming cycle, they will be un-bypassed and remain active in the system. If ‘Bypass Report’ is enabled,
the force arming zones can be programmed to report bypass when they are Force Armed (default), or to not report bypass
even if ‘Bypass Report’ is enabled (refer to system options).
Group Bypass
A designated group of zones can be programmed to bypass by pressing [Bypass]-[0]-[0]-[Bypass] prior to arming.
Group Toggle
If enabled, the panel can toggle the Group Bypass zone in and out of bypass mode by pressing the [Bypass] key. This
option if active when ever the panel is in either Partial or Full Arm mode.
LED Extinguish
This option will extinguish all LEDs on the Code Pad, except the ‘Power’ LED, after 60 seconds without a key-press.
Pressing any numeric key will illuminate all LEDs.
One Key Partial Mode Disarm
If enabled, the panel can be disarmed from the Partial Mode by pressing the Partial key.
If disabled, the panel requires a full user code to be entered to disarm the system.
Partial Mode
Partial mode allows system owners to arm only designated partial zones (e.g. downstairs, front doors, garage), bypassing
all non-partial zones (e.g. upstairs bedroom). Partial mode encourages system owners to use their alarm system more
frequently when the premise is occupied. When armed in the ‘Partial’ mode, the opening of any zones designated as ‘Partial
Mode zone’ will initiate the code pad sounder and start the Partial Mode entry delay before creating an alarm. All other
zones will be bypassed during Partial mode. To arm this area in Partial Mode, press the [Partial] key on the code pad.
Quick Arm Option
The panel has a one button ‘Quick Arm’ option that can be used to arm the system by pressing the [ON] key on the Code
Pad. If closing reports are sent, the user code will be 98.
Recent Closing
If enabled, the panel will send a ‘Recent Closing Report’ to the central station if an alarm occurs within 5 minutes after the
panel is armed. The user number that armed the system will also be sent. This option is enabled by default, but needs to
be set to report in Feature 9 for proper operation.
© Hills Industries 2009
Page 28
Area Option Descriptions
Re-exit
The panel has the ability to restart the exit delay if required without disarming the system by pressing the [Exit] key while
the system is running the exit delay. This option can only be used once per arming cycle.
Silent Auto-Arming
If enabled, the panel will Auto-Arm this area and not activate the 50 second code pad sound. This option is used when you
don’t want to alert any other area of your Auto-Arm time.
Universal Arming
When enabled, using the quick arm function (ON button on code pad) or entering a valid user code will arm the panel in
Partial mode if an exit zone is not faulted during the exit delay time.
Zone Bypassed Sounder Alert
If this option is enabled, the panel will beep the Code Pad sounder upon arming if a zone is bypassed.
Late To Close Reports new
If this option is enabled, the panel will send a Late To Close report to the central monitoring station if Contact ID is enabled
in Feature 6 and the panel has not been armed by the Closing Time in Feature 34.
Auto-Arm In Partial new
If this option is enabled and Auto-Arming is enabled in Feature 36 then the panel will Auto-Arm that area in partial mode at
the Closing Time set in Feature 34.
Disable Bypass For Force Arm Zones new
If this option is enabled then at the end of the Exit Delay if any Force Arm type zones are unsealed they will not be
bypassed and the zone will activate the alarm as per its Zone Configuration Type characteristic.
Feature 17 new
Area 1 – Entry / Exit Timers
Entry Time 1
Exit Time 1
Entry Time 2
Exit Time 2
30
60
30
60
Segments 1-6
Reserved new
Reserved new
Feature 17 sets the primary and secondary entry / exit times for area 1. Valid entries are 10-255 seconds
Zones 1 – 8 Configuration
Feature 18
Zones 1-8 Configuration Group
Segments 1-8
3
7
16
16
16
16
16
16
Feature 18 contains the Configuration Group (zone type) for zones 1-8. Segment 1 is for zone 1, and Segment 8 is for zone
8. Refer to the ‘Default Zone Configuration’ table in this section for zone type selections.
Default Zone Configurations
Zones can be programmed to be one of 32 different zone configurations (zone types). Configurations 1 to 20 can be
modified in the configuration group section of this manual. Configuration groups 21 to 31 are factory set and cannot be
altered. Choose one of the 30 default zone configurations to program into each of the zone configuration segments (e.g.
features 18, 20, 59, 61, 63, 65, 119, 121, etc). Study this table for the appropriate zone configuration group for each zone.
Data
Default Zone Configuration
0 new
Zone Disabled
1
Entry / Exit Delay 1: Partial – Forced Arming – A trip will start entry delay 1. This zone will be
active in partial mode. This zone type may be faulted while arming if forced arming is enabled in the
area options.
2
Entry / Exit Delay 1: Chime – Forced Arming – A trip will start entry delay 1. This zone will be
bypassed in partial mode. This zone type will set the code pad chime if set via the code pad [Chime]
key.
3
Entry / Exit Delay 1: Partial – Chime – Forced Arming – A trip will start entry delay 1. This zone
will be active in partial mode. This zone type may be faulted while arming if forced arming is enabled
in the area options. This zone type will set the code pad chime if set via the code pad [Chime] key.
© Hills Industries 2009
Page 29
Data
Default Zone Configuration
4
Entry / Exit Delay 2: Partial – Forced Arming – A trip will start entry delay 2. This zone will be
active in partial mode. This zone type may be faulted while arming if forced arming is enabled in the
area options.
5
Entry / Exit Delay 2: Partial – Chime – Forced Arming - A trip will start entry delay 2. This zone
will be active in partial mode. This zone type may be faulted while arming if forced arming is enabled
in the area options. This zone type will set the code pad chime if set via the code pad [Chime] key.
6
Handover: Forced Arming – Interior zone that follows the entry delay zones. Instant alarm type
unless an entry zone if faulted first. This zone will be bypassed in partial mode. This zone type may
be faulted while arming if forced arming is enabled in the area options.
7
Handover: Partial – Forced Arming – Interior zone that follows the entry delay zones. Instant alarm
type unless an entry zone if faulted first. This zone will be active in partial mode. This zone type may
be faulted while arming if forced arming is enabled in the area options.
8
Handover: Twin Trip – Forced Arming – Interior zone that follows the entry delay zones. Instant
alarm type unless an entry zone if faulted first. This zone will be bypassed in partial mode. This zone
type may be faulted while arming if forced arming is enabled in the area options. This zone type will
require two triggers or another zone would have to have been trigged before it will activate an alarm.
9
Handover: Group Isolate – Forced Arming – Interior zone that follows the entry delay zones.
Instant alarm type unless an entry zone if faulted first. This zone will be bypassed in partial mode.
This zone type may be faulted while arming if forced arming is enabled in the area options. This zone
type will be part of the group bypass zones.
10
Handover: Twin Trip – Chime – Forced Arming – Interior zone that follows the entry delay zones.
Instant alarm type unless an entry zone if faulted first. This zone will be bypassed in partial mode.
This zone type may be faulted while arming if forced arming is enabled in the area options. This zone
type will require two triggers or another zone would have to have been trigged before it will activate
an alarm. This zone type will set the code pad chime if set via the code pad [Chime] key.
11
Handover: Partial – Twin Trip – Forced Arming – Interior zone that follows the entry delay zones.
Instant alarm type unless an entry zone if faulted first. This zone will be active in partial mode. This
zone type may be faulted while arming if forced arming is enabled in the area options. This zone type
will require two triggers or another zone would have to have been trigged before it will activate an
alarm.
12
Handover: Partial – Group Bypass – Forced Arming – Interior zone that follows entry delay
zones. Instant alarm type unless an entry zone if faulted first. This zone will be active in partial mode.
This zone type may be faulted while arming if forced arming is enabled in the area options. This zone
type will be part of the group bypass zones.
13
Handover: Twin Trip – Group Bypass – Forced Arming – Interior zone that follows the entry delay
zones. Instant alarm type unless an entry zone if faulted first. This zone will be bypassed in partial
mode. This zone type may be faulted while arming if forced arming is enabled in the area options.
This zone type will require two triggers or another zone would have to have been trigged before it will
activate an alarm. This zone type will be part of the group bypass zones.
14
Handover: Partial – Twin Trip – Group Isolate – Forced Arming – Interior zone that follows the
entry delay zones. Instant alarm type unless an entry zone if faulted first. This zone will be active in
partial mode. This zone type may be faulted while arming if forced arming is enabled in the area
options. This zone type will require two triggers or another zone would have to have been trigged
before it will activate an alarm. This zone type will be part of the group bypass zones.
15
Instant: – Produces an instant alarm if tripped when armed. Ignored when disarmed. This zone will
be bypassed in partial mode.
16
Instant: Partial – Produces an instant alarm if tripped when armed. Ignored when disarmed. This
zone will be active in partial mode.
17
Instant: Partial (no DEOL) – Produces an instant alarm if tripped when armed. Ignored when
disarmed. This zone will be active in partial mode. This zone type will not be enabled for dual end of
line monitoring if enabled in the system options.
18
Instant: Twin Trip – Forced Arming – Produces an instant alarm if tripped when armed. Ignored
when disarmed. This zone will be bypassed in partial mode. This zone type may be faulted while
arming if forced arming is enabled in the area options. This zone type will require two triggers or
another zone would have to have been trigged before it will activate an alarm.
19
Instant: Group Bypass – Produces an instant alarm if tripped when armed. Ignored when disarmed.
This zone will be bypassed in partial mode. This zone type will be part of the group bypass zones.
20
Instant: Partial – Chime – Produces an instant alarm if tripped when armed. Ignored when
disarmed. This zone will be active in partial mode. This zone type will set the code pad chime if set
via the code pad [Chime] key.
© Hills Industries 2009
Page 30
Data
Default Zone Configuration (Zones 21-31 are not reprogrammable)
21
Instant: Partial – Twin Trip – Produces an instant alarm if tripped when armed. Ignored when
disarmed. This zone will be active in partial mode. This zone type will require two triggers or another
zone would have to have been trigged before it will activate an alarm.
22
Instant: Partial – Group Bypass – Produces an instant alarm if tripped when armed. Ignored when
disarmed. This zone will be active in partial mode and will be part of the group bypass zones.
23
Instant: Twin Trip – Group Bypass – Produces an instant alarm if tripped when armed. Ignored
when disarmed. This zone will be bypassed in partial mode. This zone type will require two triggers
or another zone would have to have been trigged before it will activate an alarm. This zone type will
be part of the group bypass zones.
24
Instant: Partial – Twin Trip – Group Bypass – Produces an instant alarm if tripped when armed.
Ignored when disarmed. This zone will be active in partial mode. This zone type will require two
triggers or another zone would have to have been trigged before it will activate an alarm. This zone
type will be part of the group bypass zones.
25
Instant: Local – Produces an instant alarm if tripped when armed. Ignored when disarmed. This
zone will be bypassed in partial mode. This zone will not activate the communicator.
26
24 Hour: Audible – A trip on a 24 Hour zone produces an instant alarm when armed or disarmed.
This zone type will set sirens.
27
24 Hour: Silent – A trip on a 24 Hour zone produces an instant alarm when armed or disarmed.
This zone type will not set sirens.
28
Fire: – A short on a fire zone will create an alarm condition when the system is armed or disarmed.
An open will create a Trouble condition. Requires smoke detectors wired Normally Open. Code pad
zone LED is steady for fire condition and flashing for trouble condition. After a fire activation,
press [*] [7] on the code pad to clear & reset fire zone. Note: 120 seconds of chamber full = alarm.
29
Day Zone: – When armed, a trip produces an instant alarm. When disarmed, a trip activates the
code pad sounder.
30
Key-Switch: – A zone attached to a momentary key switch will arm/disarm the panel if the zone is
momentarily shorted from a sealed condition. A 3.3K resister must be used. Note: If DEOL
monitoring is enabled in system options, this zone type must have its EOL configuration as all other
DEOL zones, i.e. two 3.3K resistors must be used to allow full line monitoring for this zone type.
31
Chime: – This zone will sound a ding-dong on code pads when unsealed. Alarm activation will
occur if armed.
Feature 19
Zone Area Select - Zones 1-8
Feature 19 is used to select the area(s) that zones 1 - 8 reside in. A zone may reside in any combination of the eight areas.
If a burglary zone resides in more than one area, it will only be active when all areas it resides in are armed. A zone that
resides in more than one area will be reported to its lowest area number. Feature 19 has 8 segments. Segment 1
corresponds to zone 1, and Segment 8 corresponds to zone 8.
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
Segment 1 – Zone 1
(1)
2
3
4
5
6
7
8
Segment 2 – Zone 2
(1)
2
3
4
5
6
7
8
Segment 3 – Zone 3
(1)
2
3
4
5
6
7
8
Segment 4 – Zone 4
(1)
2
3
4
5
6
7
8
Segment 5 – Zone 5
(1)
2
3
4
5
6
7
8
Segment 6 – Zone 6
(1)
2
3
4
5
6
7
8
Segment 7 – Zone 7
(1)
2
3
4
5
6
7
8
Segment 8 – Zone 8
(1)
2
3
4
5
6
7
8
Zones 9 – 16 Configuration
Feature 20
Segments 1-8
Zones 9-16 Configuration Group
16
16
16
16
16
16
16
16
Feature 20 contains the Configuration Group (zone type) for zones 9-16. Segment 1 is for zone 9, and Segment 8 is for
zone 16. Refer to the ‘Default Zone Configuration’ table in this section for zone type selections.
© Hills Industries 2009
Page 31
Feature 21
Zone Area Select - Zones 9-16
Feature 21 is used to select the area(s) that zones 9-16 reside in. A zone may reside in any combination of the eight areas.
If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides in
more than one area will be reported to its lowest area. Feature 21 has 8 segments. Segment 1 corresponds to zone 9 and
Segment 8 corresponds to zone 16.
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
Segment 1 – Zone 9
(1)
2
3
4
5
6
7
8
Segment 2 – Zone 10
(1)
2
3
4
5
6
7
8
Segment 3 – Zone 11
(1)
2
3
4
5
6
7
8
Segment 4 – Zone 12
(1)
2
3
4
5
6
7
8
Segment 5 – Zone 13
(1)
2
3
4
5
6
7
8
Segment 6 – Zone 14
(1)
2
3
4
5
6
7
8
Segment 7 – Zone 15
(1)
2
3
4
5
6
7
8
Segment 8 – Zone 16
(1)
2
3
4
5
6
7
8
Feature 22 new
System Options new
Feature 22 is used to enable various system option and reporting options.
Segment 1
(1)
On if siren sounds for ‘Telephone Line Cut’ when armed
2
On if siren sounds for ‘Telephone Line Cut’ when disarmed
3
On if siren blast at arming – (A siren chirp when any area is armed)
4
On if siren blast at exit expiration – (A siren chirp when any area exit delay expires)
5
On if siren blast at closing kiss-off – (A siren chirp when any area sends a closing report)
(6)
On if siren limited to once per zone
7
On if siren sounds for any Tamper
(8)
On if siren blasts 1 time for key-switch and wireless arming; 2 times for disarming
(when using NX-148E in master mode on a multi-area system, siren blasts on all area disarm)
Segment 2
1
On if siren driver should be a voltage output. Off = speaker output.
2
On if sirens should sound on expander trouble
3
On if Communicator limited to once per zone
4
On if First to Open Last to Close Reports
5
On if Battery Missing Test is performed every 12 seconds
(6)
7
(8)
On if Strobe flashes for 3 seconds for key-switch and wireless arming, 6 seconds for disarming
On if Manual Communicator Test performed during []-[44] test function
On if Box Tamper Pins on the control panel are enabled
Segment 3
(1)
On if Box Tamper reporting enabled
(2)
On if AC Fail reporting enabled
(3)
On if Low Battery reporting enabled
(4)
On if Aux Power Over-current reporting enabled
(5)
On if Siren Supervision reporting enabled
(6)
7
(8)
On if Telephone Line Cut reporting enabled
Reserved
On if Expander Trouble reporting enabled
© Hills Industries 2009
Page 32
Segment 4
(1)
On if Fail To Communicate report enabled
2
On if Log Full report enabled
(3)
On if Auto-test report enabled
(4)
On if Start/End programming report enabled
(5)
On if End Download report enabled
(6)
On if Sensor Low Battery report enabled
(7)
8
On if Sensor Missing report enabled
On if Expander Module (number) to be reported via the Contact I.D. report
Segment 5 new
(1)
2
3 new
On enable Lost Clock service light
On enables Zone Doubling
On disables all hardwired zones on the main board.
Must cycle power on/off to disable or re-enable hardwire zones.
4
On will enable all Dual End of Line (DEOL) resistors on all zones
5
On will prevent force armed zones to report bypass
6
On enables Silent Exit option
7 new
8
Reserved
On will Auto Partial Arm Area 1
Segment 6 new
1 new
Enable Two Wire Smoke
2 new
Reserved
3 new
Enable Zone Inactivity Time In Hours. Default is off = days.
4 new
Reserved
5 new
Enable DC Operation
6 new
Reserved
7 new
Enable Steady (Temporal) Siren. Default is off = Evacuation Siren for fire events.
8 new
Reserved
Segment 7 new
1 new
Reserved
2 new
Reserved
3 new
Reserved
4 new
Reserved
5 new
Reserved
6 new
Reserved
7 new
Reserved
8 new
Reserved
System Option Descriptions
Auto Partial Arm Area One
If enabled, area one will auto partial arm at the auto-arm time. If this option is enabled, area one cannot be auto-armed in
the full mode (see F 22 – Seg 5 – Op 8).
Battery Testing
The Hills Reliance can test for the presence of the battery every 12 seconds (see F 22 – Seg 2 – Op 5).
The Hills Reliance will also test the battery condition at disarm, once per 24 hour cycle.
Box Tamper
If enabled, the Hills Reliance will use the N/C Box Tamper pins provided on the main board (see F 22 – Seg 2 – Op 8).
Dual End Of Line (Zone Tamper)
If enabled, the Hills Reliance will monitor all zones except types 17 and 28 for Dual End Of Line. A short or open circuit on a
DEOL will set zone tamper alarms. Refer to the terminal wiring diagram for more detail (see F 22 – Seg 5 – Op 4).
To reset tamper condition press []-[7] on code pad.
© Hills Industries 2009
Page 33
System Option Descriptions
Enable Steady (Temporal) Siren new
If enabled this option will enable the Steady (Temporal) Siren tone and disable the Evacuation Siren tone for all fire events
and any zone that has this option set in its configuration group type.
Expanded Contact I.D.
The Hills Reliance can report all system device alarms with their individual point number if the expanded Contact I.D.
reporting is enabled (see F 22 – Seg 4 – Op 8).
First To Open / Last To Close
If enabled, the Hills Reliance will only send a closing report when the last area is armed. Note: the last area to arm must
have open/close reports enabled. The Hills Reliance will only send an opening report when the first area is disarmed. Note:
the first area to disarm must have open/close reports enabled (see F 22 – Seg 2 – Op 4).
Force Arm Bypass Reports
If enabled, the Hills Reliance restricts bypass reports when zones are forced armed. Otherwise, when a zone is forced
armed (and bypass reports are enabled), bypass reports are sent at the end of exit time. If forced armed zones re-seal
during the armed period, bypass restores are sent (see F 22 – Seg 5 – Op 5).
Limited Sirens / Communicator
If enabled, the Hills Reliance will only set one siren activation per zone and/or one alarm report per zone. This option must
be disabled if the siren and communicator attempt counter option is used. If limited communicator is enabled, restore
reports (if enabled) will be sent at disarm, otherwise restore reports will be sent as they occur (see F 22 – Seg 2 – Op 3).
Lost Clock
If enabled, the Hills Reliance will illuminate the service LED whenever the internal clock is interrupted (see F 22 – Seg 5 –
Op 1). E.g. Loss of power.
On-Board Zone Disable
If enabled, the Hills Reliance can disable the on-board hardwire zones. This is used when the Hills Reliance is used as a
totally wireless system (see F 22 – Seg 5 – Op 3).
Radio Remote Arm
If enabled, the Hills Reliance will activate the sirens every time the system is armed or disarmed with a key-switch zone or
integrated wireless keyfob. The sirens will chirp once for arming and twice for disarming. The strobe will flash for 3 seconds
for arming and 6 seconds for disarming (see F 22 – Seg 1 – Op 8).
Silent Exit Option
The exit delay can be silenced by pressing []-[Exit] before arming the control panel, or when using the re-exit option. The
exit delay can also be silenced permanently in all areas (see F 22 – Seg 5 – Op 6).
Tamper Siren
If enabled, all zone tampers and module tampers will set the system sirens (see F 22 – Seg 1 – Op 7).
Telephone Line Cut Siren
If enabled, it will set the siren for the siren time whenever the phone line monitor is activated. Reset the phone line siren by
entering a valid PIN code. This option sets phone line cut sirens in either armed and or disarmed mode. In a multi-area
system, ‘a system armed state’ would be represented by any area that is armed (see F 22 – Seg 1 – Op 1 & 2).
Two Wire Smoke new
On the Hills Reliance 128, if enabled Zone 8 and Com terminals are set for two-wire smoke detector compatibility when
Zone 8 is configured with zone type 28. Must use a 680 Ohm EOL resistor.
Voltage Output
If enabled, the on-board siren output will become a 1 Amp 12VDC output to drive 12VDC sirens (see F 22 – Seg 2 – Op 1).
Zone Doubling
If enabled, the 4/6/8 on-board zones will be doubled to 8/12/16 zones by using different resistors. E.g. on the Hills Reliance
12, zone 1 terminal will wire to zones 1 and 7, and zone 6 terminal will wire to zone 6 and 12. This option cannot be
selected for zones other than the 4/6/8 hardwired zones on the main panel. This option cannot be used in conjunction with
the Dual EOL option. (See F 22 – Seg 5 – Op 2). If zone doubling is enabled the Aux 4 two-wire smoke cannot be enabled.
Zone Inactivity Time In Hours new
If enabled the Zone Inactivity Timer in Feature 25 – Segment 11 will be set in hours not days. This feature is used when the
Zone Activity Monitor is enabled in the Zone Configuration Group type (e.g. F 68 – Seg 4 – Op 1). Zone activity is checked
hourly, so depending on the time of last activity there may be up to 1 hour delay before the zone activity is checked again
and Zone Inactivity event reported. For Zone Inactivity to report Zone Tamper Reporting must be set in Feature 9 –
Segment 1 – Option 7.
© Hills Industries 2009
Page 34
Feature 23
Siren / Communicator Attempt Counter
Segment 1
0
Feature 23 is used to set the burglary zone siren / communicator attempt counter. The number programmed in segment 1
will determine the number of alarm activations the Hills Reliance will allow before bypassing all burglary zones (1-128) that
have tripped during the arming cycle. The bypassed zones will not report trips to a base station, and the local siren or bell
will not sound for these zones. A zone trip will not be added to the number count until the zone has tripped more than once.
For this option to be valid, sirens and or the communicator must be set to unlimited in system options.
Feature 24
Code Pad Sounder Control
The panel can set the code pad sounder for most alarm conditions. Feature 24 provides 8 system alarms that can be
enabled to set the code pad sounder. A code pad sounder activation can be silenced by entering a valid user code. Note.
The AC power fail and low battery code pad sounder activations will occur the instant these conditions are present. All
options in this feature are global to all code pads.
Segment 1
(1)
(2)
On if code pad sounds for ‘Telephone Line Cut‘ when the system is armed
On if code pad sounds for ‘Telephone Line Cut‘ when disarmed
3
On if code pad sounds upon AC Power Failure
4
On if code pad sounds when a Low Battery is detected
5
On if code pad sounds during Twin Trip time
(6)
On if code pad sounds for Zone and Box Tampers
7
On if code pad sounds for Medical Alarm
8
On if code pad sounds for Expander Trouble
System Timer Configuration
Feature 25 new
System Timers
Feature 25 contains the duration of various system timing functions. Example: If you desire the duration of the Strobe time
to be 48 hours, you should program [4]-[8]-[] in segment 2 of this feature. The [4]-[8] is the number of hours, and the []
stores the data and moves to the next segment of this feature.
Segments 1-14
Seg 1
Seg 2
Seg 3
Seg 4
Seg 5
Seg 6
Seg 7
Seg 8
Seg 9
Seg 10
Seg 11
Seg 12
Seg 13
Seg 14
20
0
2
30
5
5
5
0
120
0
0
0
0
0
Segment 1
Partial Arm Entry Time (10 – 255 sec)
Segment 2
Strobe Time (0 – 255 hours)
Segment 3
Dynamic Battery Test Duration (0 – 255 min)
Segment 4
AC Failure Report Delay (0 – 255 min)
Segment 5
Siren Time (1 – 255 min)
Segment 6
Twin Trip Time (0 – 255 min)
Segment 7 new
Chime Option (‘0’ = Follow, ‘5’ = Chime once, ‘255’ = Latch)
Segment 8
Dialer Delay Time (0 – 255 sec)
Segment 9
Fire Alarm Verification Time (120 – 255 sec)
Segment 10 new
Reserved
Segment 11 new
Zone Inactivity Time (default is in days, see Feature 22 – Segment 6 – Option 3)
Segment 12 new
Reserved
Segment 13 new
Reserved
Segment 14 new
Reserved
© Hills Industries 2009
Page 35
System Timer Descriptions
Partial Arm Entry Time
The Partial Arm Entry time is the delay time that will be allocated to all active zones in Partial Arm Mode. Fire and 24 Hour
Zones will not be affected in Partial Arm Mode. The valid time selection in this segment is 10 to 255 seconds.
Strobe Time
The strobe time is the duration that output programmed to follow the strobe time will activate. The valid time selection in this
segment is 0 to 255 hours, where ‘0’ = Latching.
Dynamic Battery Test
The panel can perform a Dynamic Battery Test for the duration in this segment at the disarming of the first area after
00:00 hours once each 24-hour cycle. This option is enabled by programming a test duration in this segment. The valid time
selection in this segment is 1 to 255 minutes.
AC Fail Report
The number programmed in this segment represents the number of 1 minute increments the AC power is lost before a
communication is initiated, from 1 to 255 minutes. The AC power restore will also delay reporting until after the number of
minutes programmed in this feature has elapsed.
Siren Time
The Siren Time is the duration that the siren output and auxiliary outputs programmed to follow the siren time will activate.
The valid time selection in this segment is 1 to 255 minutes.
Twin Trip Time
This segment contains the number of one (1) minute increments in the Twin Trip Zone Time Period. The Twin Trip Zone
Time Period can be programmed in one (1) minute increments from 1 to 255. The time programmed in this feature will set
the time period whereby two or more zones must trip before an alarm condition will be registered or the one zone must
trigger twice within this time period, or a continuous trip longer than 10 seconds.
Chime Option
The code pad chime is a true chime sound, which can be set to follow the input status, chime once, or latch until a valid
code is entered. The options programmable in this segment are: ‘0’ = Follow, ‘5’ = Chime once or ‘255’ = Latch.
Dialer Delay Time
The panel can delay the dialling of all non 24-hour zones by the duration programmed in this feature. The valid time
selection in this segment is 0 to 255 seconds.
Fire Alarm Verification Time
When enabled, the panel will verify a fire alarm by requiring more than one trip on a smoke detector within the time
programmed in this segment before creating an alarm. The valid time selection in this segment is 120 to 255 seconds.
Zone Inactivity Time
This option is used to set the Zone Inactivity Time in days from 1 to 255. This option is used in conjunction with the Zone
Activity Monitor that is set in the Characteristics of the Zone Configuration Group Type.
If Feature 22 – Segment 6 – Option 3 is enabled then this time is in hours not in days, from 2 to 255 hours.
Auxiliary Output 1 – 4 Configuration
Feature 26
Auxiliary Output 1-4 Area Selection
Feature 26 is used to select which area(s) the events must occur in before the output will activate. Feature 26 has 4
segments. Segment 1 corresponds to output 1, and Segment 4 corresponds to output 4.
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
Segment 1 – Output 1
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Segment 2 – Output 2
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Segment 3 – Output 3
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Segment 4 – Output 4
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
© Hills Industries 2009
Page 36
Feature 27 new
Auxiliary Output 1-4 Special Timing
Feature 27 contains special timing option activation for the four auxiliary outputs. Segment 1 corresponds to output 1;
Segment 4 corresponds to output 4.
Hills Reliance 8 (Only) Note new : The Hills Reliance 8 has no Aux 3 terminal, instead Feature 27 – Segment 3 relates to
the SMOKE terminal. By default on the Hills Reliance 8, F 27 – Seg 3 – Opt 3 is off (i.e. “follow timer”) and Opt 6 is on (i.e.
0V output). Turn F 27 – Seg 3 – Opt 6 off if you wish to connect a smoke detector. When Option 6 is on = 0V output, off =
12V output on SMOKE terminal. This allows the SMOKE terminal to function as a voltage output relay. You may need to
program Feature 30 to use this feature (e.g. to open a garage door using a 4 button keyfob, add a relay to the terminals).
Hills Reliance 12 (Only) Note: On the Hills Reliance 12, the AUX 4 terminal is used as SMOKE + for two-wire smoke
detectors (see Feature 22). Or as Zone 7 for a four-wire smoke detector by default. The function cannot be changed.
Segments 1 – 4
Outputs 1 – 4
1
On if output should be timed in minutes; Off if timed in seconds
2
On if output should latch; Off if output should be timed
(3)
On if output should stop timing upon code entry; Off if output should follow timer
4
On if output should only activate between the closing and opening time in Features 33 and 34
5
On if output should only activate between the opening and closing time in Features 33 and 34
6
On if output should be inverted
7
Reserved
8
Reserved
Auxiliary Output 1 – 4 Logic new
The Hills Reliance 8 has 3 auxiliary outputs (Features 28, 29, 30), Reliance 12 and Reliance 128 have 4 auxiliary outputs
(Features 28, 29, 30, 31).
Features 28, 29, 30 and 31 each set an auxiliary output (1, 2, 3, and 4 respectively) for the period of time in segment 4,
based on the two events in segments 1 and 2, and the logic value set in segment 3.
The logic value is a set of rules that apply to both Event A and Event B that must be reached before the output will trigger.
There are two rules to the logic and two states that the event can be in. The two rules are ‘AND’ or ‘OR’. The ‘AND’ rule is
used when both events have to be active for the output to trigger the “OR” rule is used when either event is active for the
output to trigger. The two states for the events are ‘true’ or ‘false’ (whether the event is currently active or whether the event
is not currently active. Use the chart on the following page to select the logic value that will apply to the relevant Auxiliary
Output.
Use the chart on the following page to select the events in segment 1 and 2 that will activate the relevant Auxiliary Output.
Program the timing in segment 4, from 0-255 (minutes or seconds, depending on data programmed in Feature 27 – Seg 1).
Programming a ‘0’ makes the output follow the event.
Feature 28 new
Segments 1-4
Auxiliary Output 1 - Event and Time
Event A – 51 (strobe)
Feature 29 new
Segments 1-4
Logic – 0 (OR) new
Time – 0 new
Logic – 0 (OR) new
Time – 0 new
Logic – 0 (OR) new
Time – 0 new
Auxiliary Output 2 - Event and Time
Event A – 7 (siren)
Feature 30 new
Segments 1-4
Event B – 53 (false) new
Event B – 53 (false) new
Auxiliary Output 3 - Event and Time
Event A – 23 (ready)
Event B – 53 (false) new
Event A is 39 (smoke reset) on Reliance 8 that occurs when *7 is pressed on a code pad.
Feature 31 new
Segments 1-4
Auxiliary Output 4 - Event and Time
Event A – 21 (armed)
© Hills Industries 2009
Event B – 53 (false) new
Page 37
Logic – 0 (OR) new
Time – 0 new
Auxiliary Output Logic Selection new
Data
Logic
0
Event A or Event B
1
Event A and Event B
2
Not Event A or Event B
3
Not Event A and Event B
4
Event A or Not Event B
5
Event A and Not Event B
6
Not Event A or Not Event B
7
Not Event A and Not Event B
Auxiliary Output Event Selection
Data
Event
Data
Event
0
Burglary Alarm
28
Expander Trouble
1
Fire Alarm
29
Dynamic Battery Test Time
2
24 Hour Alarm
30
Open Period
3
Trouble Alarm
31
Closed Period
4
Tamper Alarm
32
Listen-In
5
Yelping Siren
33
Line Seizure
6
Steady Siren
34
Reserved
7
Any Siren
35
Fail To Communicate
8
Any Bypass
36
Telephone Line Fault
9
AC Fail
37
Program Mode
10
Low Battery
38
Download In Process
11
Duress
39
Smoke Reset (only for Reliance 8)
12
Aux 1 Code Pad Zone
40
Short Circuit
13
Aux 2 Code Pad Zone
41
Box Tamper
14
Panic Code Pad Zone
42
Siren Tamper
15
Code Pad Tamper
43
Any Open
16
Auto-test
44
Any Short
17
Alarm Memory
45
Any Fault (open/short on non-fire zone)
18
Entry
46
Any Alarm
19
Exit
47
Beeping Code Pad
20
Entry or Exit
48
Code Entry (see note below)
21
Armed State
49
ITI Keyfob Light Key (function 1)
22
Disarmed State
50
ITI Keyfob * Key (function 2)
23
Ready
51
Strobe
24
Not Ready
52 new
True (always on)
25
Fire
53 new
False (always off)
26
Fire Trouble
54 new
Door Unlocked
27
Chime
55 new
Access Alarm (e.g. see F68-Seg4-Op4)
© Hills Industries 2009
Page 38
Note: When event 48 is programmed, it is possible to program a user code's authorization to select which output(s) a
particular code will activate. When LED 8 is on for an authorization, then LEDs 1- 4 correspond to that code activating
outputs 1 - 4 respectively. Refer to the code pad programming section in this manual.
Feature 32
Auto-Test Control
Segments 1-4
1
168
03
00
Segment 1
Program a ’0’ if the intervals are in hours. ‘1 - 8’ if in days.
1 = SUN, 2=MON, 3=TUE, 4=WED, 5=THU, 6=FRI, 7 = SAT and 8 = DAILY
Segment 2
Program the Auto-test hourly interval from 1-255 hours, if Segment 1 is set to 0
Segment 3
Program the Auto-test report hour in 24 hour format, ignored if Segment 1 is set to 0
Segment 4
Program the Auto-test report time, number of minutes after the hour
Feature 33 new
Opening Time / Auto Disarm Time
Segments 1-2
Hours – 08
Minutes – 00
Feature 33 determines the start of the Open Window (in 24 hour format) and the end of the Close Window. This is the time
when the panel would normally be disarmed. If Auto Disarm is programmed then this is the time the panel will disarm the
selected areas on those days programmed in Feature 35.
At this time it also enables codes with ‘Arm Only After Close Window’ authority to arm and disarm the panel.
Note: Opening time must be earlier than closing time for Aux. outputs, or Code Authorization to function properly.
Feature 34
Closing Time / Auto-Arm Time
Segments 1-2
Hours – 20
Minutes – 00
Feature 34 determines the end of the Open Window (in 24 hour format) and the start of the Close Window. This is the time
when the panel would normally be armed. If Auto-Arm is programmed then this is the time the panel will arm the selected
areas. At this time, the Code Pad will beep for 50s before the panel arms. Stop/Delay the auto-arm for 45 minutes by
entering a valid code on the Code Pad. See Feature 36.
At this time it also prevents codes with ‘Arm Only After Close Window’ authority from disarming the panel.
Note: Closing time must be later than opening time for Aux. outputs, or Code Authorization to function properly.
Feature 35
Days Open / ‘Arm Only After Close Window’ Authority
Feature 35 selects which days of the week each area is open. Segment 1 is for area 1, and Segment 8 is for area 8.
Together with F33 and F34, this determines the normal operating hours of the site also known as the Open Window, when
each area would normally be disarmed. The period outside of this time and selected days is known as the Close Window
when each area would normally be armed. If a day is not selected then that entire day will be in the Close Window. If AutoArm is programmed, the panel will attempt to arm specified areas during the Close Window. Also see F33, 34 and 36.
Also on these selected days, user codes with ‘Arm Only After Close Window’ authority will be able to arm and disarm during
the Close Window. On days not selected here, codes with ‘Arm Only After Close Window’ authority will not disarm. Note
that Feature 36 can re-arm an area even after a user disarms that area if it is during the Close Window.
Segments 1-8
Areas 1 – 8
(1)
‘Arm only after close window’ will arm/disarm on Sunday, and Area is open on Sunday
(2)
‘Arm only after close window’ will arm/disarm on Monday, and Area is open on Monday
(3)
‘Arm only after close window’ will arm/disarm on Tuesday, and Area is open on Tuesday
(4)
‘Arm only after close window’ will arm/disarm on Wednesday, and Area is open on Wednesday
(5)
‘Arm only after close window’ will arm/disarm on Thursday, and Area is open on Thursday
(6)
‘Arm only after close window’ will arm/disarm on Friday, and Area is open on Friday
(7)
‘Arm only after close window’ will arm/disarm on Saturday, and Area is open on Saturday
(8)
Reserved
© Hills Industries 2009
Page 39
Feature 36 new
Days of the Week for Auto-Arming in Areas 1 - 8
Feature 36 selects which days of the week each area will auto-arm. Segment 1 is for area 1, and Segment 8 is for area 8.
Requires Features 33, 34 and 35 to be programmed to determine the Open Window.
If auto-arm is enabled, the panel will auto-arm the selected area at the Closing Time on the selected day. Note that there
may be a few minutes of delay depending on the site and programming. If a zone is faulted when the panel tries to autoarm, the zone will be bypassed. If disarmed during the Close Window, the panel will check every 45 min and try to re-arm
and keep the area secure
Option 8 relates to a retry timer. If there are zones faulted after disarming during the Close Window, the panel will wait until
there is 45 continuous minutes of no activity (i.e. Ready status) then auto-arm. The retry timer is not adjustable. Enable
option 8 to disable the retry timer, this will result in the panel arming after 45 min after disarming without waiting.
Users can stop/delay the auto-arm by entering their code during the exit time, no event log is recorded for the user code
entered.
User 97 is reported for auto-arm.
The process is:
Closing Time  Auto-Arm and unsealed zones bypassed  Disarm  Check if within Close Window  If Retry Timer
enabled, wait for 45 min continuous ready status  Else wait 45 min  Warning Time  Exit Time  Re-arm Area
Segments 1-8
Areas 1 – 8
1
Auto-Arming on Sunday
2
Auto-Arming on Monday
3
Auto-Arming on Tuesday
4
Auto-Arming on Wednesday
5
Auto-Arming on Thursday
6
Auto-Arming on Friday
7
Auto-Arming on Saturday
8 new
Disable Retry Timer (i.e. arm after 45 min regardless of activity)
Feature 37 new
Segments 1-6
Area 1 – Account Code
10
10
10
10
Reserved new
Reserved new
Feature 37 contains the account code sent when area 1 is reported. If Feature 37 is left as default (all ‘10’s), then the
system account code (Feature 5) will be used.
Only available on Reliance 12 and Reliance 128.
Areas 2 – 8 Programming Options
Feature 38 new
Segments 1-6
Area 2 – Account Code
10
10
10
10
Reserved new
Reserved new
Feature 38 contains the account code sent when area 2 is reported. If Feature 38 is left as default (all ‘10’s), then the
system account code (Feature 5) will be used.
© Hills Industries 2009
Page 40
Feature 39 new
Area 2 – Option and Report Selections
Feature 39 is used to enable certain options that can be accessed or are visible to the user from the code pad of the
system. In addition, certain communicator reports are enabled. Each of these options can be enabled by area 2.
If the option selection feature for any area is left blank, that area will use Feature 16 for the option selection.
Segment 1
1
On enables the Quick Arm option
2
On enables the Re-exit option
3
On enables the Force Arm option
4
On enables the Silent Code Pad Panic option
5
On enables the Audible Code Pad Panic option
6
On enables the Code Pad Fire option
7
On enables the Code Pad Medical option
8
On enables the Code Pad Multiple Code Attempt Tamper option
Segment 2
1
On enables the LED Extinguish option.
2
On enables the Require Code for Bypassing option
3
On enables the Zone Bypassed Sounder Alert option
4
On enables the AC Power/Low Battery Sounder Alert option
5
On enables Bypass toggle
6
On enables Silent Auto-Arm
7
On enables the Universal Arming option
8
On enables the One Key Partial Mode Disarm
Segment 3
1
On enables Opening and Closing reports
2
On enables Zone Bypass reporting
3
On enables Zone Restore reporting
4
On enables Zone Trouble reporting
5
On enables Zone Tamper reporting
6
On enables the Cancel option
7
On enables Recent Closing option
8
On enables Exit Error option
Segment 4 new
1
On enables Late To Close (requires Feature 6 to be set to Contact ID)
2
On enables Auto-Arm In Partial
3
Reserved
4
On enables Disable Bypass For Force Arm Zones
5
Reserved
6
Reserved
7
Reserved
8
Reserved
Segment 5 new
1
Reserved
2
Reserved
3
Reserved
4
Reserved
5
Reserved
6
Reserved
7
Reserved
8
Reserved
© Hills Industries 2009
Page 41
Feature 40 new
Area 2 – Entry / Exit Timers
Entry Time 1
Exit Time 1
Entry Time 2
Exit Time 2
30
60
30
60
Segments 1-6
Reserved new
Reserved new
Feature 40 sets the primary and secondary entry / exit times for area 2. If all segments in this feature are set to ‘0’, the
entry / exit time for this area will follow area 1 (Feature 17). Valid entries are 10-255 seconds.
Feature 41 new
Area 3 – Account Code
Segments 1-6
10
10
10
10
Reserved new
Reserved new
Feature 41 contains the account code sent when area 3 is reported. If Feature 41 is left un-programmed (all ‘10’s), then the
system account code (Feature 5) will be used.
Feature 42
Area 3 – Option and Report Selections
Feature 42 is used to enable certain options that can be accessed or are visible to the user from the code pad of the
system. In addition, certain communicator reports are enabled. Each of these options can be enabled by area 3.
If the option selection feature for any area is left blank, that area will use feature 16 for the option selection. Refer
to Feature 39 in this section for options table.
Feature 43 new
Area 3 – Entry / Exit Timers
Entry Time 1
Exit Time 1
Entry Time 2
Exit Time 2
30
60
30
60
Segments 1-6
Reserved new
Reserved new
Feature 43 sets the primary and secondary entry / exit times for area 3. If all segments in this feature are set to ‘0’, the
entry / exit time for this area will follow area 1 (Feature 17). Valid entries are 10-255 seconds.
Feature 44 new
Area 4 – Account Code
Segments 1-6
10
10
10
10
Reserved new
Reserved new
Feature 44 contains the account code sent when area 4 is reported. If Feature 44 is left as default (all ‘10’s), then the
system account code (Feature 5) will be used.
Feature 45
Area 4 – Option and Report Selections
Feature 45 is used to enable certain options that can be accessed or are visible to the user from the code pad of the
system. In addition, certain communicator reports are enabled. Each of these options can be enabled by area 4.
If the option selection feature for any area is left blank, that area will use Feature 16 for the option selection. Refer
to Feature 39 in this section for options table.
Feature 46 new
Area 4 – Entry / Exit Timers
Entry Time 1
Exit Time 1
Entry Time 2
Exit Time 2
30
60
30
60
Segments 1-6
Reserved new
Reserved new
Feature 46 sets the primary and secondary entry / exit times for area 4. If all segments in this feature are set to ‘0’, the
entry / exit time for this area will follow area 1 (Feature 17). Valid entries are 10-255 seconds
Feature 47 new
Segments 1-6
Area 5 – Account Code
10
10
10
10
Reserved new
Reserved new
Feature 47 contains the account code sent when area 5 is reported. If Feature 47 is left as default (all ‘10’s), then the
system account code (Feature 5) will be used.
© Hills Industries 2009
Page 42
Feature 48
Area 5 – Option and Report Selections
Feature 48 is used to enable certain options that can be accessed or are visible to the user from the code pad of the
system. In addition, certain communicator reports are enabled. Each of these options can be enabled by area 5.
If the option selection feature for any area is left blank, that area will use Feature 16 for the option selection. Refer
to Feature 39 in this section for options table.
Feature 49 new
Area 5 – Entry / Exit Timers
Entry Time 1
Exit Time 1
Entry Time 2
Exit Time 2
30
60
30
60
Segments 1-6
Reserved new
Reserved new
Feature 49 sets the primary and secondary entry / exit times for area 5. If all segments in this feature are set to ‘0’, the
entry / exit time for this area will follow area 1 (Feature 17). Valid entries are 10-255 seconds
Feature 50 new
Area 6 – Account Code
Segments 1-6
10
10
10
10
Reserved new
Reserved new
Feature 50 contains the account code sent when area 6 is reported. If Feature 50 is left as default (all ‘10’s), then the
system account code (Feature 5) will be used.
Feature 51
Area 6 – Option and Report Selections
Feature 51 is used to enable certain options that can be accessed or are visible to the user from the code pad of the
system. In addition, certain communicator reports are enabled. Each of these options can be enabled by area 6.
If the option selection feature for any area is left blank, that area will use Feature 16 for the option selection. Refer
to Feature 39 in this section for options table.
Feature 52 new
Area 6 – Entry / Exit Timers
Entry Time 1
Exit Time 1
Entry Time 2
Exit Time 2
30
60
30
60
Segments 1-6
Reserved new
Reserved new
Feature 52 sets the primary and secondary entry / exit times for area 6. If all segments in this feature are set to ‘0’, the
entry / exit time for this area will follow area 1 (Feature 17). Valid entries are 10-255 seconds
Feature 53 new
Area 7 – Account Code
Segments 1-6
10
10
10
10
Reserved new
Reserved new
Feature 53 contains the account code sent when area 7 is reported. If Feature 53 is left as default (all ‘10’s), then the
system account code (Feature 5) will be used.
Feature 54
Area 7 – Option and Report Selections
Feature 54 is used to enable certain options that can be accessed or are visible to the user from the code pad of the
system. In addition, certain communicator reports are enabled. Each of these options can be enabled by area 7.
If the option selection feature for any area is left blank, that area will use Feature 16 for the option selection. Refer
to Feature 39 in this section for options table.
Feature 55 new
Area 7 – Entry / Exit Timers
Entry Time 1
Exit Time 1
Entry Time 2
Exit Time 2
30
60
30
60
Segments 1-6
Reserved new
Reserved new
Feature 55 sets the primary and secondary entry / exit times for area 7. If all segments in this Feature are set to ‘0’, the
entry / exit time for this area will follow area 1 (Feature 17). Valid entries are 10-255 seconds.
© Hills Industries 2009
Page 43
Feature 56 new
Area 8 – Account Code
Segments 1-6
10
10
10
10
Reserved new
Reserved new
Feature 56 contains the account code sent when area 8 is reported. If Feature 56 is left as default (all ‘10’s), then the
account code corresponding to the phone number dialled will be used.
Feature 57
Area 8 – Option and Report Selections
Feature 57 is used to enable certain options that can be accessed or are visible to the user from the code pad of the
system. In addition, certain communicator reports are enabled. Each of these options can be enabled by area 8.
If the option selection feature for any area is left blank, that area will use Feature 16 for the option selection. Refer
to Feature 39 in this section for options table.
Feature 58 new
Area 8 – Entry / Exit Timers
Entry Time 1
Exit Time 1
Entry Time 2
Exit Time 2
30
60
30
60
Segments 1-6
Reserved new
Reserved new
Feature 58 sets the primary and secondary entry / exit times for area 8. If all segments in this Feature are set to ‘0’, the
entry / exit time for this area will follow area 1 (Feature 17). Valid entries are 10-255 seconds.
Zones 17 – 48 Configuration
Feature 59
Segments 1-8
Zones 17-24 Configuration Group
16
16
16
16
16
16
16
16
Feature 59 contains the Configuration Group (zone type) for zones 17-24. Segment 1 is for zone 17, and Segment 8 is for
zone 24.
Feature 60
Zone Area Select - Zones 17-24
Feature 60 is used to select the area(s) that zones 17-24 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area. Feature 60 has 8 segments. Segment 1 corresponds to zone 17
and Segment 8 corresponds to zone 24.
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
Segment 1 – Zone 17
(1)
2
3
4
5
6
7
8
Segment 2 – Zone 18
(1)
2
3
4
5
6
7
8
Segment 3 – Zone 19
(1)
2
3
4
5
6
7
8
Segment 4 – Zone 20
(1)
2
3
4
5
6
7
8
Segment 5 – Zone 21
(1)
2
3
4
5
6
7
8
Segment 6 – Zone 22
(1)
2
3
4
5
6
7
8
Segment 7 – Zone 23
(1)
2
3
4
5
6
7
8
Segment 8 – Zone 24
(1)
2
3
4
5
6
7
8
Feature 61
Segments 1-8
Zones 25-32 Configuration Group
16
16
16
16
16
16
16
16
Feature 61 contains the Configuration Group (zone type) for zones 25-32. Segment 1 is for zone 25, and Segment 8 is for
zone 32.
© Hills Industries 2009
Page 44
Feature 62
Zone Area Select - Zones 25-32
Feature 62 is used to select the area(s) that zones 25-32 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area. Feature 62 has 8 segments. Segment 1 corresponds to zone 25
and Segment 8 corresponds to zone 32.
Refer to Feature 60 in this section for the zone area select table.
Feature 63
Segments 1-8
Zones 33-40 Configuration Group
16
16
16
16
16
16
16
16
Feature 63 contains the Configuration Group (zone type) for zones 33-40. Segment 1 is for zone 33, and Segment 8 is for
zone 40.
Feature 64
Zone Area Select - Zones 33-40
Feature 64 is used to select the area(s) that zones 33-40 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area. Feature 64 has 8 segments. Segment 1 corresponds to zone 33
and Segment 8 corresponds to zone 40.
Refer to Feature 60 in this section for the zone area select table.
Feature 65
Segments 1-8
Zones 41-48 Configuration Group
16
16
16
16
16
16
16
16
Feature 65 contains the Configuration Group (zone type) for zones 41-48. Segment 1 is zone 41, and Segment 8 is zone
48.
Feature 66
Zone Area Select - Zones 41-48
Feature 66 is used to select the area(s) that zones 41-48 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area. Feature 66 has 8 segments. Segment 1 corresponds to zone 41
and Segment 8 corresponds to zone 48.
Refer to Feature 60 in this section for the zone area select table.
Configuration Groups 1 – 20
Features 67-106 are used to change the zone configurations as listed in the Default Zone Configuration Table in zones 1 to
128 configuration section. These features are considered advanced programming and should only be changed with a
thorough understanding of the operation of each bit.
Feature 67
Configuration Group 1 Alarm Event Code
Segment 1
3
Feature 67 contains the Contact I.D. event code sent for zone configuration group 1 alarm reports. The desired event code
should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
© Hills Industries 2009
Page 45
Feature 68 new
Configuration Group 1 Characteristic Select
Segment 1
1
Fire (turn on if this is a fire zone)
2
24 hour (turn on for non-fire 24 hour zones)
3
Key-switch zone (normally open switch)
4
Follower (turn on for burglary zones that are Instant during non-entry times)
(5)
Delay 1 zone (follows timer 1 entry and exit times)
6
Delay 2 zone (follows timer 2 entry and exit times)
7
Reserved
8
Local only (turn on if this zone should not be reported)
Segment 2
1
(2)
On if configuration group will beep the code pad for alarm
On if configuration group will sound the yelping siren for alarm
3
On if configuration group will sound the steady (temporal) siren for alarm
4
On if configuration group will chime
(5)
6
On if configuration group can be bypassed
On if configuration group is included in the Group Bypass
(7)
On if configuration group is Force Arm
(8)
On if configuration group is Active in Partial Mode
Segment 3
1
(2)
Reserved
On enables Double End Of Line (DEOL) Tamper Zone
3
On enables Trouble Reporting zone (Day Zones and Fire Zones)
4
On if configuration group is a Twin Trip Zone
(5)
On enables Dialer Delay Zone
(6)
On if configuration group will siren / communicator attempt count
(7)
On enables Restore reporting
(8) new
Reserved
Segment 4 new
2 new
Zone Activity Monitor (also see F25 – Seg 11 – Opt 11 and F22 – Seg 6 – Opt 3 to the set timer, and
Zone Tamper Reporting must also be enabled in F9 – Seg 1 – Opt 7)
EOL Resistor Defeat (if enabled, a short = seal, open circuit = unseal)
3 new
Request To Exit (REX button) (triggers Request To Exit event for NX508E Output Expander board)
4 new
Access Control (applies to NX1701EAU reader, triggers DOTL and Forced Door access violations for
NX508E Output Expander board)
5 new
Reserved
6 new
Reserved
7 new
Reserved
8 new
Reserved
1 new
Segment 5 new
1 new
Reserved
2 new
Reserved
3 new
Reserved
4 new
Reserved
5 new
Reserved
6 new
Reserved
7 new
Reserved
8 new
Reserved
© Hills Industries 2009
Page 46
Feature 69
Configuration Group 2 Alarm Event Code
Segment 1
3
Feature 69 contains the Contact I.D. event code sent for zone configuration group 2 alarm reports. The desired event code
should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 70 new
Seg 1
Configuration Group 2 Characteristic Select
5
Seg 2
2457
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Configuration Group 3 Alarm Event Code
Feature 71
Segment 1
3
Feature 71 contains the Contact I.D. event code sent for zone configuration group 3 alarm reports. The desired event code
should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 72 new
Seg 1
Configuration Group 3 Characteristic Select
5
Seg 2
24578
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 73
Configuration Group 4 Alarm Event Code
Segment 1
3
Feature 73 contains the Contact I.D. event code sent for zone configuration group 4 alarm reports. The desired event code
should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 74 new
Seg 1
Configuration Group 4 Characteristic Select
6
Seg 2
2578
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 75
Configuration Group 5 Alarm Event Code
Segment 1
3
Feature 75 contains the Contact I.D. event code sent for zone configuration group 5 alarm reports. The desired event code
should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 76 new
Seg 1
Configuration Group 5 Characteristic Select
6
Seg 2
24578
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 77
Configuration Group 6 Alarm Event Code
Segment 1
3
Feature 77 contains the Contact I.D. event code sent for zone configuration group 6 alarm reports. The desired event code
should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
© Hills Industries 2009
Page 47
Feature 78 new
Seg 1
Configuration Group 6 Characteristic Select
4
Seg 2
257
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 79
Configuration Group 7 Alarm Event Code
Segment 1
3
Feature 79 contains the Contact I.D. event code sent for zone configuration group 7 alarm reports. The desired event code
should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 80 new
Seg 1
Configuration Group 7 Characteristic Select
4
Seg 2
2578
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 81
Configuration Group 8 Alarm Event Code
Segment 1
3
Feature 81 contains the Contact I.D. event code sent for zone configuration group 8 alarm reports. The desired event code
should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 82 new
Seg 1
Configuration Group 8 Characteristic Select
4
Seg 2
257
Seg 3
245678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 83
Configuration Group 9 Alarm Event Code
Segment 1
3
Feature 83 contains the Contact I.D. event code sent for zone configuration group 9 alarm reports. The desired event code
should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 84 new
Seg 1
Configuration Group 9 Characteristic Select
4
Seg 2
2567
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 85
Configuration Group 10 Alarm Event Code
Segment 1
3
Feature 85 contains the Contact I.D. event code sent for zone configuration group 10 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 86 new
Seg 1
Configuration Group 10 Characteristic Select
4
Seg 2
2457
Seg 3
245678
Seg 4 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
© Hills Industries 2009
Page 48
Seg 5 new
Feature 87
Configuration Group 11 Alarm Event Code
Segment 1
3
Feature 87 contains the Contact I.D. event code sent for zone configuration group 11 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 88 new
Seg 1
Configuration Group 11 Characteristic Select
4
Seg 2
2578
Seg 3
245678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 89
Configuration Group 12 Alarm Event Code
Segment 1
3
Feature 89 contains the Contact I.D. event code sent for zone configuration group 12 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 90 new
Seg 1
Configuration Group 12 Characteristic Select
4
Seg 2
25678
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 91
Configuration Group 13 Alarm Event Code
Segment 1
3
Feature 91 contains the Contact I.D. event code sent for zone configuration group 13 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Configuration Group 13 Characteristic Select
Feature 92 new
Seg 1
4
Seg 2
2567
Seg 3
245678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 93
Configuration Group 14 Alarm Event Code
Segment 1
3
Feature 93 contains the Contact I.D. event code sent for zone configuration group 14 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 94 new
Seg 1
Configuration Group 14 Characteristic Select
4
Seg 2
25678
Seg 3
245678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 95
Configuration Group 15 Alarm Event Code
Segment 1
3
Feature 95 contains the Contact I.D. event code sent for zone configuration group 15 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
© Hills Industries 2009
Page 49
Feature 96 new
Seg 1
Configuration Group 15 Characteristic Select
Seg 2
25
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 97
Configuration Group 16 Alarm Event Code
Segment 1
3
Feature 97 contains the Contact I.D. event code sent for zone configuration group 16 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 98 new
Seg 1
Configuration Group 16 Characteristic Select
Seg 2
258
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 99
Configuration Group 17 Alarm Event Code
Segment 1
3
Feature 99 contains the Contact I.D. event code sent for zone configuration group 17 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 100 new
Seg 1
Configuration Group 17 Characteristic Select
Seg 2
258
Seg 3
5678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 101
Configuration Group 18 Alarm Event Code
Segment 1
3
Feature 101 contains the Contact I.D. event code sent for zone configuration group 18 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 102 new
Seg 1
Configuration Group 18 Characteristic Select
Seg 2
257
Seg 3
245678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Feature 103
Configuration Group 19 Alarm Event Code
Segment 1
3
Feature 103 contains the Contact I.D. event code sent for zone configuration group 19 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 104 new
Seg 1
Configuration Group 19 Characteristic Select
Seg 2
256
Seg 3
25678
Seg 4 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
© Hills Industries 2009
Page 50
Seg 5 new
Feature 105
Configuration Group 20 Alarm Event Code
Segment 1
3
Feature 105 contains the Contact I.D. event code sent for zone configuration group 20 alarm reports. The desired event
code should be chosen from the Contact I.D. Configuration Group Event Table in the Appendix section.
Feature 106 new
Configuration Group 20 Characteristic Select
Seg 1
Seg 2
2458
Seg 3
25678
Seg 4 new
Seg 5 new
Use ‘Configuration Group Characteristic table’ described in Feature 68, of this section.
Zones 49 – 128 Configuration new
Feature 119 new
Segments 1-8
Zones 49-56 Configuration Group
16
16
16
16
16
16
16
16
Feature 119 contains the Configuration Group (zone type) for zones 49-56. Segment 1 is for zone 49, and Segment 8 is for
zone 56.
Feature 120 new
Zone Area Select - Zones 49-56
Feature 120 is used to select the area(s) that zones 49-56 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area. Feature 120 has 8 segments. Segment 1 corresponds to zone 49
and Segment 8 corresponds to zone 56.
Refer to Feature 60 for the zone area select table.
Feature 121 new
Segments 1-8
Zones 57-64 Configuration Group
16
16
16
16
16
16
16
16
Feature 121 contains the Configuration Group (zone type) for zones 57-64. Segment 1 is for zone 57, and Segment 8 is for
zone 64.
Feature 122 new
Zone Area Select - Zones 57-64
Feature 122 is used to select the area(s) that zones 57-64 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area. Feature 122 has 8 segments. Segment 1 corresponds to zone 57
and Segment 8 corresponds to zone 64.
Refer to Feature 60 for the zone area select table.
Feature 123 new
Segments 1-8
Zones 65-72 Configuration Group
16
16
16
16
16
16
16
16
Feature 123 contains the Configuration Group (zone type) for zones 65-72. Segment 1 is for zone 65, and Segment 8 is for
zone 72.
Feature 124 new
Zone Area Select - Zones 65-72
Feature 124 is used to select the area(s) that zones 65-72 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area.
Refer to Feature 60 for the zone area select table.
© Hills Industries 2009
Page 51
Feature 125 new
Segments 1-8
Zones 73-80 Configuration Group
16
16
16
16
16
16
16
16
Feature 125 contains the Configuration Group (zone type) for zones 73-80. Segment 1 is for zone 73, and Segment 8 is for
zone 80.
Feature 126 new
Zone Area Select - Zones 73-80
Feature 126 is used to select the area(s) that zones 73-80 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area.
Refer to Feature 60 for the zone area select table.
Feature 127 new
Segments 1-8
Zones 81-88 Configuration Group
16
16
16
16
16
16
16
16
Feature 127 contains the Configuration Group (zone type) for zones 81-88. Segment 1 is for zone 81, and Segment 8 is for
zone 88.
Feature 128 new
Zone Area Select - Zones 81-88
Feature 128 is used to select the area(s) that zones 81-88 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area.
Refer to Feature 60 for the zone area select table.
Feature 129 new
Segments 1-8
Zones 89-96 Configuration Group
16
16
16
16
16
16
16
16
Feature 129 contains the Configuration Group (zone type) for zones 89-96. Segment 1 is for zone 89, and Segment 8 is for
zone 96.
Feature 130 new
Zone Area Select - Zones 89-96
Feature 130 is used to select the area(s) that zones 89-96 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area.
Refer to Feature 60 for the zone area select table.
Feature 131 new
Segments 1-8
Zones 97-104 Configuration Group
16
16
16
16
16
16
16
16
Feature 131 contains the Configuration Group (zone type) for zones 97-104. Segment 1 is for zone 97, and Segment 8 is
for zone 104.
Feature 132 new
Zone Area Select - Zones 97-104
Feature 132 is used to select the area(s) that zones 97-104 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area.
Refer to Feature 60 for the zone area select table.
© Hills Industries 2009
Page 52
Feature 133 new
Segments 1-8
Zones 105-112 Configuration Group
16
16
16
16
16
16
16
16
Feature 133 contains the Configuration Group (zone type) for zones 105-112. Segment 1 is for zone 105, and Segment 8 is
for zone 112.
Feature 134 new
Zone Area Select - Zones 105-112
Feature 134 is used to select the area(s) that zones 105-112 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area.
Refer to Feature 60 for the zone area select table.
Feature 135 new
Segments 1-8
Zones 113-120 Configuration Group
16
16
16
16
16
16
16
16
Feature 135 contains the Configuration Group (zone type) for zones 113-120. Segment 1 is for zone 113, and Segment 8 is
for zone 120.
Feature 136 new
Zone Area Select - Zones 113-120
Feature 136 is used to select the area(s) that zones 113-120 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area.
Refer to Feature 60 for the zone area select table.
Feature 137 new
Segments 1-8
Zones 121-128 Configuration Group
16
16
16
16
16
16
16
16
Feature 137 contains the Configuration Group (zone type) for zones 121-128. Segment 1 is for zone 121, and Segment 8 is
for zone 128.
Feature 138 new
Zone Area Select - Zones 121-128
Feature 138 is used to select the area(s) that zones 121-128 reside in. A zone may reside in any combination of the eight
areas. If a burglary zone resides in more than one area, it will only be active when all areas are armed. A zone that resides
in more than one area will be reported to its lowest area.
Refer to Feature 60 for the zone area select table.
© Hills Industries 2009
Page 53
Feature 155 new
Days of the Week for Auto Disarm Areas 1 - 8
Feature 36 selects which days of the week each area will auto disarm at the Opening Time. Segment 1 is for area 1, and
Segment 8 is for area 8.
Use this feature with caution, ensure you have programmed the Open Window correctly (Feature 33, 34, 35).
Segments 1-8
Areas 1 – 8
1
Auto Disarming on Sunday
2
Auto Disarming on Monday
3
Auto Disarming on Tuesday
4
Auto Disarming on Wednesday
5
Auto Disarming on Thursday
6
Auto Disarming on Friday
7
Auto Disarming on Saturday
8
Reserved
Feature 162 new
EOL Resistor Value Select
0
Segment 1
Feature 162 is used to select the value of resistor that is used as the End Of Line monitoring for the zones. Only applies to
hardwire zones on main panel (address 0). Note that this feature does not work when the panel has zone doubling
enabled and does not apply to zone expanders.
© Hills Industries 2009
Data
EOL Resistor Value
0
3K3
1
1K5
2
2K2
3
3K9
4
4K7
5
5K6
6
6K8
Page 54
Appendix 1: Reporting Zone Codes in Contact I.D.
The Hills Reliance control panel has the ability to report Ademco Contact I.D. transmissions. Each report in Contact I.D.
consists of an event code and the zone I.D. generating the alarm. The event code will come from the chart below and be
programmed in the configuration group event code.
© Hills Industries 2009
Programmed
Event Code
Contact I.D.
Code
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
122
110
120
130
131
132
133
134
135
150
121
100
123
137
602
151
158
154
140
140
159
Description
Silent Panic
Fire Alarm
Panic Alarm
Burglary Alarm
Perimeter Alarm
Interior Alarm
24 Hour Burglary
Entry Alarm
Day/Night Alarm
Non Burglary 24 Hour
Duress Alarm
Medical Alarm
Audible Panic Alarm
Tamper Alarm
Periodic Test
Gas Detected
High Temp
Water Leakage
General Alarm
General Alarm
Low Temp
Page 55
Appendix 2: Reporting Fixed Codes in Contact I.D.
The table below lists the CID event codes sent for the following reports (if enabled). The number in brackets following the
event is the number that will be reported as the zone number if extended Contact I.D. is enabled in the system options.
Otherwise zone ‘0’ will always be reported. If there are no parentheses, the zone will be reported as ‘0’.
Contact I.D.
Event
Report
Manual Test
Auto test Open (user number)
Close (user number)
Cancel (user number)
Download Complete
Start Program
End Program
Ground Fault
Ground Fault Restore
Recent Close (user number)
Exit Error (user number)
Event Log Full
Fail To Communicate
Expander Trouble
Expander Restore
Telephone Fault
Telephone Restore
Siren Tamper
Siren Restore
Aux Power Over Current
Aux Power Restore
Low Battery
Low Battery Restore
AC Fail
AC Restore
Box Tamper
Box Tamper Restore
Code Pad Tamper
Code Pad Panic
Duress
Code Pad Fire
Code Pad Medical
RF Sensor Lost (zone number)
RF Sensor Restore (zone number)
Sensor Low Battery (zone number)
Sensor Battery Restore (zone number)
Zone Trouble (zone number)
Zone Trouble Restore (zone number)
Zone Tamper (zone number)
Zone Tamper Restore (zone number)
Zone Bypass (zone number)
Bypass Restore (zone number)
Zone Inactivity
Late To Close
Forced Door
© Hills Industries 2009
Page 56
601
602
401
406
412
627
628
310
310
401
457
605
354
333
333
351
351
321
321
312
312
309
309
301
301
137
137
137
120
121
110
100
381
381
384
384
380
380
137
137
570
570
391 new
454 new
423 new
Appendix 3: Expander Numbers for Reporting Expander Trouble
The tables below list the device numbers that will be reported for each expander/code pad that has a trouble condition if
expanded Contact I.D. is enabled system options.
Code Pads Module Number Table
Code Pad
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
1
192
193
194
195
196
197
198
199
2
200
201
202
203
204
205
206
207
3
208
209
210
211
212
213
214
215
4
216
217
218
219
220
221
222
223
5
224
225
226
227
228
229
230
231
6
232
233
234
235
236
237
238
239
7
240
241
242
243
244
245
246
247
8
248
249
250
251
252
253
254
255
Switch 6
NX-216 Zone Expanders
Note: Must power down before changing address/starting zone number
Module
Number
Reported
Starting
Zone
Number
Switch 1
Switch 2
Switch 3
Switch 4
1st
23
9
ON
OFF
OFF
nd
16
17
OFF
ON
OFF
3rd
17
25
ON
ON
OFF
th
18
33
OFF
OFF
ON
th
19
41
ON
OFF
ON
When
set ON,
disables
upper
8 zones
on
NX-216
module
2
4
5
NX-216E Zone Expanders new
Note: Must power down before changing address/starting zone number
Module
Number
Reported
Starting
Zone
Number
Switch 1
Switch 2
Switch 3
Switch 4
Switch 5
1st
22
1
OFF
OFF
OFF
OFF
OFF
nd
23
9
ON
OFF
OFF
OFF
OFF
3rd
16
17
OFF
ON
OFF
OFF
OFF
th
17
25
ON
ON
OFF
OFF
OFF
th
18
33
OFF
OFF
ON
OFF
OFF
th
19
41
ON
OFF
ON
OFF
OFF
th
7
20
49
OFF
ON
ON
OFF
OFF
8th
21
57
ON
ON
ON
OFF
OFF
th
2
4
5
6
9
96
65
OFF
OFF
OFF
ON
OFF
th
10
97
73
ON
OFF
OFF
ON
OFF
11th
98
81
OFF
ON
OFF
ON
OFF
th
99
89
ON
ON
OFF
ON
OFF
th
100
97
OFF
OFF
ON
ON
OFF
th
101
105
ON
OFF
ON
ON
OFF
th
15
102
113
OFF
ON
ON
ON
OFF
16th
103
121
ON
ON
ON
ON
OFF
12
13
14
© Hills Industries 2009
Page 57
When
set ON,
disables
upper
8 zones
on
NX-216E
module
NX-408E / NX-416E / NX-448E Wireless Receiver Address Settings
Module
Number
Reported
Switch 1
Switch 2
Switch 3
Switch 4
1st
32
ON
OFF
ON
OFF
nd
33
OFF
ON
ON
OFF
rd
34
ON
ON
ON
OFF
th
4
35
OFF
OFF
OFF
OFF
5th
36
ON
OFF
OFF
OFF
th
37
OFF
ON
OFF
OFF
th
7
38
ON
ON
OFF
OFF
8th
39
OFF
OFF
ON
OFF
2
3
6
NX-507E / NX-508E Relay / Output Expanders
Module
Number
Reported
Switch 1
Switch 2
Switch 3
1st
24
ON
ON
OFF
nd
25
OFF
OFF
ON
rd
3
26
ON
OFF
ON
4th
27
OFF
ON
ON
5th
28
ON
ON
ON
6th
29
OFF
OFF
OFF
th
7
30
ON
OFF
OFF
8th
31
OFF
ON
OFF
2
Switch 4
When
set to
OFF
disables
tamper
feature
Max no. of
NX-507E / NX-508E
modules supported
Reliance 8 = 3
Reliance 12\128 = 8
NX-320 Remote Power Supply
Module
Number
Reported
Switch 1
Switch 2
Switch 3
1st
84
OFF
OFF
OFF
2nd
85
ON
OFF
OFF
rd
86
OFF
ON
OFF
th
4
87
ON
ON
OFF
5th
88
OFF
OFF
ON
th
89
ON
OFF
ON
th
90
OFF
ON
ON
th
91
ON
ON
ON
3
6
7
8
Recommendation
It is highly advised to disconnect all power (incl backup battery) from the panel before connecting new expander modules,
on power up the control panel will enrol modules. Next enter program mode and default the new module:
[] 8 [Program Code] [Module Number] # 9 1 0 # [Exit] [Exit] [Wait 10 seconds] the module is now ready to be
used/programmed.
© Hills Industries 2009
Page 58
Appendix 4: Troubleshooting System Problems
Device
Code Pad
Problem
Remedy
Code pad appears dead - no lights or sounds when keys are pressed.
1.
Measure the output voltage at the Aux Pwr (+) terminals. Voltage should be above
12.8 volt dc.
2.
Disconnect all devices connected to Aux Pwr (+) terminal leaving only the code pad
connected.
3.
Check for short circuits on devices connected to Aux Pwr (+) terminals.
4.
Check that AC power and battery are correctly connected to panel.
5. Check wiring and connections at code pad & panel.
Code pad lights appear OK, but no functions when the keys are pressed.
1.
Check the user code you are entering is programmed on the system and is an
Arm/Disarm code.
2. Check the code pad No and Area No are set correctly. That is feature  94 in
section “Programming the code pad”.
Code pad jumps to area 2, chime turns off, or case tamper comes on by itself.
1. Check the code pad and expanders are new “E” versions (e.g. NX-216E, NX-148E).
Fire LED flashes rapidly.
1.
Measure Aux Pwr (+) terminal. Voltage should be above 12.8 Volt DC.
2.
Check Data wire is connected correctly at both ends.
3.
Smoke detector circuit may have gone into alarm. Press  7 to reset.
4. Try connecting code pads one at a time and see if problem is related to a particular
code pad.
After exiting from program mode code pad will not accept key presses.
1.
Wait 12 seconds after leaving program mode before entering key presses at the
code pad. The panel is enrolling all devices.
Unable to write custom messages to multiple LCD code pads on system.
1.
Ensure you have individually set the code pad No(s) and Area No(s) for each code
pad. That is feature  94 in section Programming the Code Pad.
2.
Enter and then exit program mode to enrol code pads.
3. Program custom messages on code pad 1.
4. Or enter Custom Messages menu, view any message and then exit.
See feature  92 in the NX-148E LCD Code Pad installation manual.
Zones LED(s) flash rapidly, Arming and Disarming will not clear condition.
1.
A zone tamper condition has occurred.
2.
Press  7 to reset condition and clear rapid flashing LED’s.
3. If the zone is still in tamper the  7 will only clear the condition temporarily.
Starts beeping and you must enter a code to stop the beeps.
1.
© Hills Industries 2009
There is a system fault present. Press  2 to see why the system started beeping.
Page 59
System
Service Light “ON” - Pressing  2 displays LED 1.
Press the (1) key and observe which LED comes on to indicate one of the
following:
1. Over Current Fault
A partial short-circuit on the Aux Pwr, Smoke power, Horn Speaker, Strobe
Screamer will cause over current faults. Removing the short from the Aux Pwr
Smoke Pwr will fix the over current condition. If the short is on the horn, Strobe
Screamer you must put the panel into alarm once the fault has been removed
clear the over current condition.
or
or
or
to
On the Reliance 8 and 12 power will be restored on fixing the condition. On the
Reliance 128 power will be restored when the thermistor resets (fuseless design).
Note if a severe short circuit is present it may exceed the protection available and
output power will not be restored.
2. Siren Trouble
The Horn Speaker is open / short circuit or not connected.
The Hills Reliance control panel monitors the siren output for faults and tampering. If
a horn speaker is not connected to the panel place a 3K3 resistor across the Bell
output to disable Siren Trouble Monitoring.
3. Box Tamper
The box tamper pins are open circuit or activated. Ensure the box tamper pins are
sealed (closed circuit). Arm and Disarm system to clear box tamper condition.
4. Expander Power
An expander connected to the system has a short circuit on the Aux output.
Expander that can report this condition are power supply (NX320).
5. Expander Low Battery
An expansion device connected to the Hills Reliance system has a Low Battery
condition. Expander that can indicate low battery conditions: NX320 power supply.
Replace Battery.
6. Expander Box Tamper
An expansion device connected to the Hills Reliance system has a tamper activated.
Check the tamper contacts on the expansion devices connected.
Expanders that can indicate box tamper: Code pads, Hardwire zone expanders and
Wireless zone expanders.
7. Expander Trouble
Code pads are not number correctly (see  94 code pad program).
Expander connected is not seen by system. Enter and Exit program mode.
You are trying to zone double a NX4 panel (not supported).
Only the Hills Reliance 8, Reliance 12, and Reliance 128 can be zone doubled.
Any device connected to the data terminal on the Hills Reliance system can cause an
expander trouble condition.
8. Reserved
System
Service Light “ON” - Pressing  2 displays LED 2.
Zone Tamper has been activated. Press the (2) key and the zone(s) that activated
the tamper will be displayed. Press the (#) key twice to exit. Press  7 is reset
tamper condition.
Service Light “ON” - Pressing  2 displays LED 3.
Low Battery (wireless zones only). Press the (3) key and the wireless zone(s) with
low battery will be displayed. Press the (#) key twice to exit.
© Hills Industries 2009
Page 60
System
Service Light “ON” - Pressing  2 displays LED 4.
Loss of Supervision (wireless zone only). Press the (4) key and the wireless zone(s)
with Loss of Supervision will be displayed. Press the (#) key twice to exit.
Service Light “ON” - Pressing  2 displays LED 5.
Zone Trouble. Press the (5) key and the zone that has trouble will be displayed. Zone
trouble only applies to Fire type zones. Press the (#) key twice to exit. Press  7 to
reset zone trouble condition.
Service Light “ON” - Pressing  2 displays LED 6.
Telephone line trouble/Line cut, when telephone line is cut from panel.
Service Light “ON” - Pressing  2 displays LED 7.
When light number 7 is lit this indicates that the panel has failed to communicate to
the base station. This led can only be extinguished by communicating to the base.
Check Phone No, Account Code and Format programming.
Press the (#) key twice to exit.
Service Light “ON” - Pressing  2 displays LED 8.
When light 8 is lit this indicates that the panel has lost time. Press the (#) key twice
to exit.
To set system time:
 97 (go to program code), enter time (4 digits) Eg 10:30am = 1030
© Hills Industries 2009
Page 61
Installation Floor Plan
Instructions
1.
2.
3.
4.
Sketch the layout of the building using the grid to scale dimensions
Identify the position of the control panel, sirens and code pads
Identify the location of all detectors and verify device coverage with device specifications
Plan models and quantities of hardware on the table below
Installation Parts List
Device
Control Panel
Siren (Internal)
Siren (External)
Strobe
PIRs
Reed switches
Detector cable
Data cable
Battery
Power Supply
Smart Power Supply
© Hills Industries 2009
Model / Quantity
Device
Code Pads (VN)
Code Pads (LED)
Code Pads (LCD)
Code Pads (Icon)
7 Relay Module
8 Output Module
16 Zone Expander
Smoke Alarms
Wireless Receiver
Key Fobs
Page 62
Model / Quantity
3
0
0
Go To Program Code Area and Authorisation
1
Go To Program Code
Reserved
On enables ‘Go To Program Code’ as an Arm Only after closing
On enables ‘Go To Program Code’ as a Master code (can change user codes)
On enables ‘Go To Program Code’ as an Arm/Disarm code
On enables ‘Go To Program Code’ to bypass zones
On enables ‘Go To Program Code’ opening and closing reports
Reserved
3
4
5
6
7
8
On enables the ‘Go To Program Code’ for area #5
On enables the ‘Go To Program Code’ for area #6
On enables the ‘Go To Program Code’ for area #7
On enables the ‘Go To Program Code’ for area #8
5
6
7
8
15
3
15
15
15
On enables the ‘Go To Program Code’ for area #4
4
15
On enables the ‘Go To Program Code’ for area #3
3
Duress Code
On enables the ‘Go To Program Code’ for area #2
2
Feat.
On enables the ‘Go To Program Code’ for area #1
1
15
On enables ‘Go To Program Code’ as an Arm Only code
2
Segment 2
Reserved
Segment 1
7
8
1
2
Feat.
9
1
Feat.
to
Requires valid user code entry for [*][9][8] and [*][9][9] functions to work
3
Enables 6 digit code. All Arm/Disarm/Go to Program codes require 6 digits
2
Segment 1
User Code Requirements
1
0
Feat.
Program Planning Sheets
23
Pg
23
Pg
23
Pg
23
Pg
14
14
8
Feat.
14
14
7
Feat.
0
6
Feat.
10
5
14
14
14
14
10
14
14
Feat.
14
14
4
Feat.
14
14
14
14
14
14
10
10
10
14
14
14
14
14
14
Phone # 3
14
14
Phone # 2
14
14
14
14
14
14
14
14
Communicator Format
10
System Account Code
14
14
Phone # 1
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
25
Pg
24
Pg
24
Pg
24
Pg
24
Pg
Opening / Closing (alarm system off = Open, alarm system on = Close)
Bypass and Bypass Restore
Zone Trouble and Restore
Power Trouble (AC Failure or Low Battery) and Restore
Zone and Box Tampers and Restore
Test Reports
3
4
5
6
7
8
6
0
6
Reserved
Reserved
Recent Closing / Exit Error
0
0
0
0
Segment 2
0
0
Number of calls to answer download
Number of rings
15
16
25
26
Pg
26
Pg
Download Control
14
14
14
14
14
14
On enables the Code Pad Medical option
Multiple Code Attempt Tamper option
7
8
Reserved
Reserved
Reserved
Reserved
5
6
7
8
On disables Bypass for Force Arm Zones
Reserved
3
4
On enables the Autoarm In Partial option
2
On enables the Late To Close option
Segment 4
On enables the Code Pad Fire option
On enables the Audible Code Pad Panic
6
5
On enables the Force Arm option
3
On enables the Silent Code Pad Panic
On enables the Re-exit option
2
4
On enables the Quick Arm option
1
1
14
14
14
14
14
14
14
14
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Enables One Key Partial Mode Disarming
On enables the Universal Arming option
On enables Silent Auto Arm
On enables Bypass toggle
AC Power/Low Battery Sounder Alert
Zone Bypassed Sounder Alert option
Require User Code for bypassing zones
On enables the LED Extinguish option
Segment 2
Area 1 - Options and Report Selections
14
14
Callback Phone Number
On enables Call Back at Auto Test Interval
On locks out download section (can only be changed through download software)
On locks out communicator programming (can only be changed through download software)
On locks all local programming (can only be changed through download software)
On enables Control Panel Shutdown (can only be changed through download software)
On requires Call Back before Download Session
Reserved
On enables two call Answering Machine Defeat
Segment 1
Feat.
Pg
14
14
Feat.
25
8
7
6
5
4
3
2
Pg
Cancel Code (also set for each area, Feat 16 - Seg 3 - Op 6)
Program, Download, & Full Log (also set Feat 22 - Seg 4 - Op 2)
Sensor Lost / Sensor Low Battery
Failure to Communicate
1
14
25
Segment 1
Feat.
Pg
System Trouble (siren, phone, expander, short circuit, earth fault)
No. of Rings / Calls to Answer Download
0
Download Access Code
0
8
7
6
5
4
3
2
1
Segment 2
Dialing Options (0 = No function, 1 = Dual Report, 4 = Extended Phone Number)
Dial Attempts
Phone Line Cut Delay
Segment 1
13
Feat.
1
12
Feat.
0
11
Feat.
Segment 2
Segment 1
10
Dial Attempts \ Dialing Options
Alarm Restores
Feat.
Alarms
2
Segment 1
Event Report Summary
1
9
Feat.
14
14
8
7
6
5
4
3
2
1
On enables Exit Error option
On enables Recent Closing option
On enables the Cancel option
On enables Zone Tamper reporting
On enables Zone Trouble reporting
On enables Zone Restore reporting
On enables Zone Bypass reporting
On enables Opening and Closing reports
Segment 3
27
Pg
26
Pg
26
Pg
16
16
16
3
4
5
6
7
8
3
4
5
6
7
8
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
16
16
16
16
Segment 2
(Zone 10)
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
8
7
6
5
4
3
2
1
Segment 3
(Zone 11)
Zone 9-16 Area Selection
16
Segment 1
(Zone 9)
21
Feat.
16
20
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Segment 4
(Zone 4)
16
8
7
6
5
4
3
2
1
Segment 4
(Zone 12)
16
Zone 9-16 Configuration Groups
2
2
Area 2
Feat.
1
1
Area 1
16
Segment 3
(Zone 3)
Zone 1-8 Area Selection
16
Segment 2
(Zone 2)
16
7
Segment 1
(Zone 1)
19
Feat.
3
18
8
7
6
5
4
3
2
1
Segment 5
(Zone 13)
8
7
6
5
4
3
2
1
Segment 5
(Zone 5)
Segment 6
Segment 4
Segment 2
Zone 1-8 Configuration Groups
Segment 5
Feat.
Reserved
Segment 3
Entry Timer #1
Entry Timer #2
30
30
Area 1 - Entry / Exit Timers
Segment 1
17
Feat.
8
7
6
5
4
3
2
1
Segment 6
(Zone 14)
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Segment 7
(Zone 15)
8
7
6
5
4
3
2
1
Segment 7
(Zone 7)
Reserved
Exit Timer #2
Exit Timer #1
Segment 6
(Zone 6)
60
60
8
7
6
5
4
3
2
1
Segment 8
(Zone 16)
8
7
6
5
4
3
2
1
Segment 8
(Zone 8)
32
Pg
31
Pg
31
Pg
29
Pg
On if siren sounds for a Zone or Box Tamper
7
Reserved
7
Reserved
7
Reserved
Reserved
7
23
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
32
Pg
Reserved
35
Pg
Disable Steady (Temporal) Siren (On enables Evacuation Siren for fire
Disable Clean-Me Reports (not used in Australia)
Reserved
Reserved
Enable Zone Inactivity Time In Hours
Reserved
Enable Two Wire Smoke
Segment 6
On if Expander Module (number) to be reported via the Contact I.D
On if Sensor Missing report enabled
On if Sensor Low Battery report enabled
On if End Download report enabled
On if Start/End programming report enabled
On if Auto-test report enabled
On if Log Full report enabled
On if Fail To Communicate report enabled
Segment 4
On if Box Tamper Pins on the control panel are enabled
On if Manual Communicator Test performed during [*]-[44] function
On if Strobe flashes for 3s for Key-switch Arm and 6s for Disarm
On if Battery Missing Test is performed every 12 seconds
On if First to Open Last to Close Reports
On if Communicator limited to once per zone
On if sirens should sound on expander trouble
On to enable Voltage Output; Off to enable On-board Siren Driver
Segment 2
Siren / Communicator Attempt Count
Reserved
Reserved
6
8
Reserved
Reserved
3
5
Reserved
2
4
Reserved
1
Segment 7
On will Auto Partial Arm Area 1
On enables Silent Exit option
6
8
On will prevent force armed zones to report bypass
On will enable all Dual End of Line (DEOL) resistors on all zones
On disables all hardwired zones on the NX board
On enables Zone Doubling
On enable Lost Clock service light
5
4
3
2
1
Segment 5
On if Expander Trouble reporting enabled
On if Telephone Line Cut report enabled
6
8
On if Siren Supervision report enabled
5
On if Low Battery reporting enabled
3
On if Auxilary Power Over-current report enabled
On if AC Fail reporting enabled
2
4
On if Box Tamper report enabled
1
Segment 3
Siren blasts 1x for key-switch / wireless arming; 2x for disarming
On if siren limited to once per zone
8
On if siren blast at closing kiss-off
6
On if siren blast at exit delay expiration
4
5
On if siren blast at arming
3
On if siren sounds for ‘Telephone Line Cut’ when armed
On if siren sounds for ‘Telephone Line Cut’ when disarmed
Feat.
0
System Options
2
1
22
29
Segment 1
Feat.
Pg
Code Pad Sounder Control
On if code pad sounds upon AC Power Failure
On if code pad sounds when a Low Battery is detected
On if code pad sounds during Twin Trip time
On if code pad sounds for Zone and Box Tampers
On if code pad sounds for Medical Alarm
On if code pad sounds for Expander Trouble
3
4
5
6
7
8
Segment 14
Segment 13
Segment 12
Segment 11
Segment 10
Segment 9
Segment 8
Segment 7
Segment 6
Segment 5
Segment 4
Segment 3
Segment 2
Segment 1
25
0
0
0
0
0
120
0
5
5
5
30
2
0
20
Reserved
Reserved
Reserved
Zone Inactivity Time (days) (see Feature 22, Segment 6, Option 3 to change to hours)
Reserved
Fire Alarm Verification Time (120 – 255 sec)
Dialer Delay Time (0 - 255 sec)
Chime Option (‘0’ = Follow, ‘5’ = Chime once, ‘255’ = Latch)
Twin Trip Time (0 - 255 min)
Siren Time (1 - 255 min)
AC Failure Report Delay (0 -255 min)
Dynamic Battery Test Duration (0 – 255 min)
Strobe Time (0 - 255 hours)
Partial Arm Entry Time (10 - 255 sec)
System Timers
On if code pad sounds for ‘Telephone Line Cut‘ when disarmed
2
Feat.
On if code pad sounds for ‘Telephone Line Cut ‘ when the system is armed
1
Segment 1
24
Feat.
35
Pg
26
35
0
Logic for Aux Out 1
(Default Logic 0 = OR)
Event A for Aux Out 1
(Default Event 51 = Strobe)
Segment 4
Segment 2
Segment 3
0
7
Logic for Aux Out 2
(Default Logic 0 = OR)
Event A for Aux Out 2
(Default Event 7 = Any Siren)
Segment 4
Segment 2
Auxiliary Output 2 - Event & Time
Segment 1
29
Feat.
Segment 3
51
Auxiliary Output 1 - Event & Time
Segment 1
28
Feat.
8
53
0
53
0
8
7
7
Reserved
Reserved
6
6
5
5
On if output to only activate between the opening and closing time (F33, F44)
On if output inverted (0 volts going to 12 volts when activated)
4
3
3
4
2
1
2
1
On if output to only activate between the closing and opening time (F33, F34)
On if output should stop timing upon code entry; Off if output to follow timer
On if output should latch; Off if output should be timed
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Timing for Aux Out 2
(Default Timing 0 = Follow)
Event B for Aux Out 2
(Default Event 53 = False)
Timing for Aux Out 1
(Default Timing 0 = Follow)
Event B for Aux Out 1
(Default Event 53 = False)
8
7
6
5
4
3
2
1
Segment 1 Segment 2 Segment 3 Segment 4
(Aux Out 1) (Aux Out 2) (Aux Out 3) (Aux Out 4)
Auxiliary Outputs 1-4 Special Timing
8
7
6
5
4
3
2
1
Segment 1 Segment 2 Segment 3 Segment 4
(Aux Out 1) (Aux Out 2) (Aux Out 3) (Aux Out 4)
Auxiliary Output 1-4 Area Selection
On if output should be timed in minutes; Off if timed in seconds
27
Feat.
Area 8
Area 7
Area 6
Area 5
Area 4
Area 3
Area 2
Area 1
Feat.
Pg
37
Pg
37
Pg
37
Pg
36
Pg
Segment 2
Segment 1
34
Logic for Aux Out 4
(Default Logic 0 = OR)
Event A for Aux Out 4
(Default Event 21 = Armed)
0
3
168
1
0
8
0
20
0
53
0
53
Timing for Aux Out 4
(Default Timing 0 = Follow)
Event B for Aux Out 4
(Default Event 53 = False)
Timing for Aux Out 3
(Default Timing 0 = Follow)
Event B for Aux Out 3
(Default Event 53 = False)
Auto-test minute
Auto-test hour (ignored if Feature 32 - Segment 1 set to 0)
Auto-test hourly test interval (1-255 hours) (Feature 32 - Segment 1 must be set to 0)
Auto-test day (0=hourly, 1=Sun, 2=Mon, 3=Tue, 4=Wed, 5=Thur, 6=Fri, 7=Sat, 8=Daily test)
Segment 4
Segment 2
Minutes
Hours
Minutes
Hours
Closing Time / Auto Arm Time
Segment 2
Feat.
Segment 4
Segment 2
Opening Time / Auto Disarm Time
Segment 1
33
Feat.
Segment 4
Segment 3
Segment 2
Segment 1
32
0
21
Auto-Test Control
Segment 3
Feat.
Logic for Aux Out 3
(Default Logic 0 = OR)
Event A for Aux Out 3
(Default Event 23 = Ready)
Auxiliary Output 4 - Event & Time
Segment 1
31
Feat.
Segment 3
0
23
Auxiliary Output 3 - Event & Time
Segment 1
30
Feat.
39
Pg
39
Pg
39
Pg
37
Pg
10
37
10
Sun
8
7
6
5
4
3
2
1
Sun
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 4
(Area 4)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 5
(Area 5)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 6
(Area 6)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 2
(Area 2)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 3
(Area 3)
8
7
6
5
4
3
2
1
10
10
10
10
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 4
(Area 4)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 5
(Area 5)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 6
(Area 6)
Days of the Week for Auto Arm Areas 1-8
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Segment 3
(Area 3)
Area 1 Account Code
Reserved
8
Feat.
Sat
Fri
6
7
Thur
Wed
5
Tue
4
Mon
2
3
Sun
1
Segment 1
(Area 1)
36
Feat.
8
7
6
5
4
3
2
1
Segment 2
(Area 2)
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 7
(Area 7)
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 7
(Area 7)
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Days Open / ‘Arm Only After Close’ Window Authority
Reserved
Sat
8
7
Thur
5
Fri
Wed
4
6
Tue
3
Sun
Mon
2
1
35
37
Segment 1
(Area 1)
Feat.
Pg
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 8
(Area 8)
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 8
(Area 8)
40
Pg
40
Pg
39
Pg
10
10
10
On enables the Re-exit option
On enables the Force Arm option
On enables the Silent Code Pad Panic
On enables the Audible Code Pad Panic
On enables the Code Pad Fire option
On enables the Code Pad Medical option
Multiple Code Attempt Tamper option
2
3
4
5
6
7
8
On enables the Autoarm In Partial option
Reserved
On disables Bypass for Force Arm Zones
Reserved
Reserved
Reserved
Reserved
2
3
4
5
6
7
8
Segment 5
Segment 3
Segment 1
40
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
0
30
30
Reserved
Entry Timer #2
Entry Timer #1
Segment 6
Segment 4
Segment 2
0
60
60
Enables One Key Partial Mode Disarming
On enables the Universal Arming option
On enables Silent Auto Arm
On enables Bypass toggle
AC Power/Low Battery Sounder Alert
Zone Bypassed Sounder Alert option
Require User Code for bypassing zones
On enables the LED Extinguish option
Segment 2
Area 2 - Entry / Exit Timers
On enables the Late To Close option
1
Segment 4
On enables the Quick Arm option
1
Feat.
10
Area 2 - Options and Report Selections
10
Area 2 - Account Code
Segment 1
39
Feat.
10
38
Feat.
8
7
6
5
4
3
2
1
Reserved
Exit Timer #2
Exit Timer #1
On enables Exit Error option
43
10
10
Multiple Code Attempt Tamper option
On enables the Code Pad Medical option
On enables the Code Pad Fire option
On enables the Audible Code Pad Panic
On enables the Silent Code Pad Panic
On enables the Force Arm option
On enables the Re-exit option
On enables the Quick Arm option
10
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Segment 5
Segment 3
0
30
30
Reserved
Entry Timer #2
Entry Timer #1
Segment 6
Segment 4
Segment 2
0
60
60
Enables One Key Partial Mode Disarming
On enables the Universal Arming option
On enables Silent Auto Arm
On enables Bypass toggle
AC Power/Low Battery Sounder Alert
Zone Bypassed Sounder Alert option
Require User Code for bypassing zones
On enables the LED Extinguish option
Segment 2
Area 3 - Entry / Exit Timers
Reserved
Reserved
Reserved
Reserved
On disables Bypass for Force Arm Zones
Reserved
On enables the Autoarm In Partial option
On enables the Late To Close option
Segment 1
Feat.
10
Area 3 - Options and Report Selections
Segment 4
42
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
Pg
On enables Recent Closing option
On enables the Cancel option
On enables Zone Tamper reporting
On enables Zone Trouble reporting
On enables Zone Restore reporting
On enables Zone Bypass reporting
1
42
41
10
Area 3 - Account Code
Segment 1
Feat.
Pg
On enables Opening and Closing reports
Segment 3
41
40
10
Feat.
Pg
8
7
6
5
4
3
2
1
Reserved
Exit Timer #2
Exit Timer #1
On enables Exit Error option
42
Pg
On enables Recent Closing option
On enables the Cancel option
On enables Zone Tamper reporting
On enables Zone Trouble reporting
On enables Zone Restore reporting
On enables Zone Bypass reporting
On enables Opening and Closing reports
Segment 3
42
Pg
42
Pg
10
10
10
On enables the Re-exit option
On enables the Force Arm option
On enables the Silent Code Pad Panic
On enables the Audible Code Pad Panic
On enables the Code Pad Fire option
On enables the Code Pad Medical option
Multiple Code Attempt Tamper option
2
3
4
5
6
7
8
On enables the Autoarm In Partial option
Reserved
On disables Bypass for Force Arm Zones
Reserved
Reserved
Reserved
Reserved
2
3
4
5
6
7
8
Segment 5
Segment 3
Segment 1
46
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
0
30
30
Reserved
Entry Timer #2
Entry Timer #1
Segment 6
Segment 4
Segment 2
0
60
60
Enables One Key Partial Mode Disarming
On enables the Universal Arming option
On enables Silent Auto Arm
On enables Bypass toggle
AC Power/Low Battery Sounder Alert
Zone Bypassed Sounder Alert option
Require User Code for bypassing zones
On enables the LED Extinguish option
Segment 2
Area 4 - Entry / Exit Timers
On enables the Late To Close option
1
Segment 4
On enables the Quick Arm option
1
Feat.
10
Area 4 - Options and Report Selections
10
Area 4 - Account Code
Segment 1
45
Feat.
10
44
Feat.
8
7
6
5
4
3
2
1
Reserved
Exit Timer #2
Exit Timer #1
On enables Exit Error option
49
10
10
Multiple Code Attempt Tamper option
On enables the Code Pad Medical option
On enables the Code Pad Fire option
On enables the Audible Code Pad Panic
On enables the Silent Code Pad Panic
On enables the Force Arm option
On enables the Re-exit option
On enables the Quick Arm option
10
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Segment 5
Segment 3
0
30
30
Reserved
Entry Timer #2
Entry Timer #1
Segment 6
Segment 4
Segment 2
0
60
60
Enables One Key Partial Mode Disarming
On enables the Universal Arming option
On enables Silent Auto Arm
On enables Bypass toggle
AC Power/Low Battery Sounder Alert
Zone Bypassed Sounder Alert option
Require User Code for bypassing zones
On enables the LED Extinguish option
Segment 2
Area 5 - Entry / Exit Timers
Reserved
Reserved
Reserved
Reserved
On disables Bypass for Force Arm Zones
Reserved
On enables the Autoarm In Partial option
On enables the Late To Close option
Segment 1
Feat.
10
Area 5 - Options and Report Selections
Segment 4
42
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
Pg
On enables Recent Closing option
On enables the Cancel option
On enables Zone Tamper reporting
On enables Zone Trouble reporting
On enables Zone Restore reporting
On enables Zone Bypass reporting
1
48
42
10
Area 5 - Account Code
Segment 1
Feat.
Pg
On enables Opening and Closing reports
Segment 3
47
42
10
Feat.
Pg
8
7
6
5
4
3
2
1
Reserved
Exit Timer #2
Exit Timer #1
On enables Exit Error option
43
Pg
On enables Recent Closing option
On enables the Cancel option
On enables Zone Tamper reporting
On enables Zone Trouble reporting
On enables Zone Restore reporting
On enables Zone Bypass reporting
On enables Opening and Closing reports
Segment 3
43
Pg
42
Pg
10
10
10
On enables the Re-exit option
On enables the Force Arm option
On enables the Silent Code Pad Panic
On enables the Audible Code Pad Panic
On enables the Code Pad Fire option
On enables the Code Pad Medical option
Multiple Code Attempt Tamper option
2
3
4
5
6
7
8
On enables the Autoarm In Partial option
Reserved
On disables Bypass for Force Arm Zones
Reserved
Reserved
Reserved
Reserved
2
3
4
5
6
7
8
Segment 5
Segment 3
Segment 1
52
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
0
30
30
Reserved
Entry Timer #2
Entry Timer #1
Segment 6
Segment 4
Segment 2
0
60
60
Enables One Key Partial Mode Disarming
On enables the Universal Arming option
On enables Silent Auto Arm
On enables Bypass toggle
AC Power/Low Battery Sounder Alert
Zone Bypassed Sounder Alert option
Require User Code for bypassing zones
On enables the LED Extinguish option
Segment 2
Area 6 - Entry / Exit Timers
On enables the Late To Close option
1
Segment 4
On enables the Quick Arm option
1
Feat.
10
Area 6 - Options and Report Selections
10
Area 6 - Account Code
Segment 1
51
Feat.
10
50
Feat.
8
7
6
5
4
3
2
1
Reserved
Exit Timer #2
Exit Timer #1
On enables Exit Error option
55
10
10
Multiple Code Attempt Tamper option
On enables the Code Pad Medical option
On enables the Code Pad Fire option
On enables the Audible Code Pad Panic
On enables the Silent Code Pad Panic
On enables the Force Arm option
On enables the Re-exit option
On enables the Quick Arm option
10
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Segment 5
Segment 3
0
30
30
Reserved
Entry Timer #2
Entry Timer #1
Segment 6
Segment 4
Segment 2
0
60
60
Enables One Key Partial Mode Disarming
On enables the Universal Arming option
On enables Silent Auto Arm
On enables Bypass toggle
AC Power/Low Battery Sounder Alert
Zone Bypassed Sounder Alert option
Require User Code for bypassing zones
On enables the LED Extinguish option
Segment 2
Area 7 - Entry / Exit Timers
Reserved
Reserved
Reserved
Reserved
On disables Bypass for Force Arm Zones
Reserved
On enables the Autoarm In Partial option
On enables the Late To Close option
Segment 1
Feat.
10
Area 7 - Options and Report Selections
Segment 4
43
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
Pg
On enables Recent Closing option
On enables the Cancel option
On enables Zone Tamper reporting
On enables Zone Trouble reporting
On enables Zone Restore reporting
On enables Zone Bypass reporting
1
54
43
10
Area 7 - Account Code
Segment 1
Feat.
Pg
On enables Opening and Closing reports
Segment 3
53
43
10
Feat.
Pg
8
7
6
5
4
3
2
1
Reserved
Exit Timer #2
Exit Timer #1
On enables Exit Error option
43
Pg
On enables Recent Closing option
On enables the Cancel option
On enables Zone Tamper reporting
On enables Zone Trouble reporting
On enables Zone Restore reporting
On enables Zone Bypass reporting
On enables Opening and Closing reports
Segment 3
43
Pg
43
Pg
10
10
10
10
On enables the Re-exit option
On enables the Force Arm option
On enables the Silent Code Pad Panic
On enables the Audible Code Pad Panic
On enables the Code Pad Fire option
On enables the Code Pad Medical option
Multiple Code Attempt Tamper option
2
3
4
5
6
7
8
Reserved
Reserved
Reserved
Reserved
4
5
6
7
8
8
7
6
5
Reserved
Reserved
Reserved
Reserved
Segment 5
Segment 3
0
30
30
Reserved
Entry Timer #2
Entry Timer #1
Area 8 - Entry / Exit Timers
Segment 1
58
Feat.
3
On disables Bypass for Force Arm Zones
3
Reserved
Reserved
Reserved
4
Reserved
On enables the Autoarm In Partial option
Reserved
2
On enables the Late To Close option
Segment 5
Segment 6
Segment 4
Segment 2
0
60
60
Enables One Key Partial Mode Disarming
On enables the Universal Arming option
On enables Silent Auto Arm
On enables Bypass toggle
AC Power/Low Battery Sounder Alert
Zone Bypassed Sounder Alert option
Require User Code for bypassing zones
On enables the LED Extinguish option
2
1
8
7
6
5
4
3
2
1
1
Segment 4
On enables the Quick Arm option
1
Segment 2
Area 8 - Options and Report Selections
10
Area 8 - Account Code
Segment 1
57
Feat.
10
56
Feat.
8
7
6
5
4
3
2
1
60
44
Reserved
Exit Timer #2
Exit Timer #1
On enables Exit Error option
44
Pg
On enables Recent Closing option
On enables the Cancel option
On enables Zone Tamper reporting
On enables Zone Trouble reporting
On enables Zone Restore reporting
On enables Zone Bypass reporting
16
16
8
7
6
5
4
3
2
1
Segment 2
(Zone 18)
8
7
6
5
4
3
2
1
Segment 3
(Zone 19)
16
16
16
16
8
8
7
6
6
Area 6
7
5
5
4
4
Area 4
Area 5
3
3
Area 3
2
Segment 2
(Zone 26)
1
Segment 1
(Zone 25)
8
7
6
5
4
3
2
1
Segment 3
(Zone 27)
Zone 25-32 Area Selection
16
2
Area 8
16
8
7
6
5
4
3
2
1
Segment 4
(Zone 20)
16
8
7
6
5
4
3
2
1
Segment 4
(Zone 28)
16
Zone 25-32 Configuration Groups
8
7
6
5
4
3
2
1
Segment 1
(Zone 17)
1
Area 7
16
Zone 17-24 Area Selection
16
Area 2
16
16
Zone 17-24 Configuration Groups
Area 1
62
Feat.
16
61
Feat.
Area 8
Area 7
Area 6
Area 5
Area 4
Area 3
Area 2
Area 1
Feat.
Pg
On enables Opening and Closing reports
Segment 3
59
44
16
Feat.
Pg
8
7
6
5
4
3
2
1
Segment 5
(Zone 29)
8
7
6
5
4
3
2
1
Segment 5
(Zone 21)
8
7
6
5
4
3
2
1
Segment 6
(Zone 30)
8
7
6
5
4
3
2
1
Segment 6
(Zone 22)
8
7
6
5
4
3
2
1
Segment 7
(Zone 31)
8
7
6
5
4
3
2
1
Segment 7
(Zone 23)
8
7
6
5
4
3
2
1
Segment 8
(Zone 32)
8
7
6
5
4
3
2
1
Segment 8
(Zone 24)
45
Pg
44
Pg
44
Pg
44
Pg
16
16
16
2
3
4
5
6
7
8
2
3
4
5
6
7
8
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
16
16
16
16
Segment 2
(Zone 42)
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
8
7
6
5
4
3
2
1
Segment 3
(Zone 43)
Zone 41-48 Area Selection
16
Segment 1
(Zone 41)
66
Feat.
16
65
8
7
6
5
4
3
2
1
Segment 3
(Zone 35)
8
7
6
5
4
3
2
1
Segment 4
(Zone 36)
16
8
7
6
5
4
3
2
1
Segment 4
(Zone 44)
16
Zone 41-48 Configuration Groups
1
1
Area 1
Feat.
16
Zone 33-40 Area Selection
16
Segment 2
(Zone 34)
16
16
Zone 33-40 Configuration Groups
Segment 1
(Zone 33)
64
Feat.
16
63
Feat.
8
7
6
5
4
3
2
1
Segment 5
(Zone 45)
8
7
6
5
4
3
2
1
Segment 5
(Zone 37)
8
7
6
5
4
3
2
1
Segment 6
(Zone 46)
8
7
6
5
4
3
2
1
Segment 6
(Zone 38)
8
7
6
5
4
3
2
1
Segment 7
(Zone 47)
8
7
6
5
4
3
2
1
Segment 7
(Zone 39)
8
7
6
5
4
3
2
1
Segment 8
(Zone 48)
8
7
6
5
4
3
2
1
Segment 8
(Zone 40)
45
Pg
45
Pg
On if configuration group will siren / communicator attempt count
On enables Restore reporting
6
7
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
On enables Dialer Delay zone
5
8
On if configuration group is a Twin Trip Zone
On enables Trouble Reporting zone (Day zone & Fire zones)
3
4
On enables Double End of Line Tamper zone
Reserved
Segment 3
Local only (turn on if this zone should not be reported)
Reserved
Delay 2 zone (follows timer 2 entry and exit times)
Delay 1 zone (follows timer 1 entry and exit times)
Follower (turn on for burglary zones that are instant during non-entry
Key-switch zone (normally open switch)
24 hour (turn on for non-fire 24 hour zones)
Fire (turn on if this is a fire zone)
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
46
Pg
45
Pg
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit (REX button)
EOL Resistor Defeat (if enables, a short = seal, open circuit = unseal)
Zone Activity Monitor
Segment 4
On if configuration group is Active in Partial Mode
On if configuration group is Force Arm
On if configuration group is included in the Group Bypass
On if configuration group can be bypassed
On if configuration group will chime
On if configuration group will sound the steady (temporal) siren for
On if configuration group will sound the yelping siren for alarm
On if configuration group will beep the code pad for alarm
Segment 2
Configuration Group 1 - Characteristic Select
2
1
8
7
6
5
4
3
2
1
68
Configuration Group 1 - Alarm Event Code
Segment 1
Feat.
45
3
67
Feat.
Pg
45
Pg
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
3
4
5
6
7
8
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Fire
24 hour
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
Segment 2
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Configuration Group 3 - Characteristic Select
Segment 1
72
Feat.
3
71
8
7
6
5
4
3
2
1
Segment 3
Configuration Group 3 - Alarm Event Code
24 hour
2
Feat.
Fire
1
Segment 2
Configuration Group 2 - Characteristic Select
Configuration Group 2 - Alarm Event Code
Segment 1
70
Feat.
3
69
Feat.
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
73
47
75
47
8
7
6
5
4
3
2
1
76
47
Local only
Reserved
Delay 2
Delay 1
Follower
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
Segment 2
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Configuration Group 5 - Characteristic Select
Key-switch
24 hour
Fire
8
7
6
5
4
3
2
1
Segment 3
Configuration Group 5 - Alarm Event Code
Local only
Reserved
Delay 2
Delay 1
Follower
Key-switch
24 hour
Fire
Segment 2
Configuration Group 4 - Characteristic Select
Segment 1
Feat.
Pg
3
Feat.
Pg
8
7
6
5
4
3
2
1
74
47
Configuration Group 4 - Alarm Event Code
Segment 1
Feat.
Pg
3
Feat.
Pg
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
47
Pg
47
Pg
47
Pg
47
Pg
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
3
4
5
6
7
8
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Fire
24 hour
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
Segment 2
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Configuration Group 7 - Characteristic Select
Segment 1
80
Feat.
3
79
8
7
6
5
4
3
2
1
Segment 3
Configuration Group 7 - Alarm Event Code
24 hour
2
Feat.
Fire
1
Segment 2
Configuration Group 6 - Characteristic Select
Configuration Group 6 - Alarm Event Code
Segment 1
78
Feat.
3
77
Feat.
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
81
47
83
48
8
7
6
5
4
3
2
1
84
48
Local only
Reserved
Delay 2
Delay 1
Follower
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
Segment 2
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Configuration Group 9 - Characteristic Select
Key-switch
24 hour
Fire
8
7
6
5
4
3
2
1
Segment 3
Configuration Group 9 - Alarm Event Code
Local only
Reserved
Delay 2
Delay 1
Follower
Key-switch
24 hour
Fire
Segment 2
Configuration Group 8 - Characteristic Select
Segment 1
Feat.
Pg
3
Feat.
Pg
8
7
6
5
4
3
2
1
82
48
Configuration Group 8 - Alarm Event Code
Segment 1
Feat.
Pg
3
Feat.
Pg
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
48
Pg
48
Pg
48
Pg
48
Pg
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
3
4
5
6
7
8
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Fire
24 hour
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
Segment 2
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Configuration Group 11 - Characteristic Select
Segment 1
88
Feat.
3
87
8
7
6
5
4
3
2
1
Segment 3
Configuration Group 11 - Alarm Event Code
24 hour
2
Feat.
Fire
1
Segment 2
Configuration Group 10 - Characteristic Select
Configuration Group 10 - Alarm Event Code
Segment 1
86
Feat.
3
85
Feat.
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
89
48
91
49
8
7
6
5
4
3
2
1
92
49
Local only
Reserved
Delay 2
Delay 1
Follower
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
Segment 2
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Configuration Group 13 - Characteristic Select
Key-switch
24 hour
Fire
8
7
6
5
4
3
2
1
Segment 3
Configuration Group 13 - Alarm Event Code
Local only
Reserved
Delay 2
Delay 1
Follower
Key-switch
24 hour
Fire
Segment 2
Configuration Group 12 - Characteristic Select
Segment 1
Feat.
Pg
3
Feat.
Pg
8
7
6
5
4
3
2
1
90
48
Configuration Group 12 - Alarm Event Code
Segment 1
Feat.
Pg
3
Feat.
Pg
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
49
Pg
49
Pg
49
Pg
49
Pg
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
3
4
5
6
7
8
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Fire
24 hour
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
Segment 2
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Configuration Group 15 - Characteristic Select
Segment 1
96
Feat.
3
95
8
7
6
5
4
3
2
1
Segment 3
Configuration Group 15 - Alarm Event Code
24 hour
2
Feat.
Fire
1
Segment 2
Configuration Group 14 - Characteristic Select
Configuration Group 14 - Alarm Event Code
Segment 1
94
Feat.
3
93
Feat.
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
97
49
50
Pg
99
49
8
7
6
5
4
3
2
1
Local only
Reserved
Delay 2
Delay 1
Follower
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
Segment 2
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Configuration Group 17 - Characteristic Select
Key-switch
24 hour
Fire
8
7
6
5
4
3
2
1
Segment 3
Configuration Group 17 - Alarm Event Code
Local only
Reserved
Delay 2
Delay 1
Follower
Key-switch
24 hour
Fire
Segment 2
Configuration Group 16 - Characteristic Select
Segment 1
100
Feat.
3
Feat.
Pg
8
7
6
5
4
3
2
1
98
49
Configuration Group 16 - Alarm Event Code
Segment 1
Feat.
Pg
3
Feat.
Pg
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
50
Pg
50
Pg
50
Pg
50
Pg
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
3
4
5
6
7
8
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Fire
24 hour
Key-switch
Follower
Delay 1
Delay 2
Reserved
Local only
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
Segment 2
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 4
Configuration Group 19 - Characteristic Select
Segment 1
104
Feat.
3
103
8
7
6
5
4
3
2
1
Segment 3
Configuration Group 19 - Alarm Event Code
24 hour
2
Feat.
Fire
1
Segment 2
Configuration Group 18 - Characteristic Select
Configuration Group 18 - Alarm Event Code
Segment 1
102
Feat.
3
101
Feat.
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 5
50
Pg
50
Pg
50
Pg
50
Pg
Area 8
Area 7
Area 6
Area 5
Area 4
Area 3
Area 2
16
8
7
6
5
4
3
2
1
Partial Mode
Force Arm
Group Bypass
Bypass
Chime
Steady siren
Yelping siren
Code pad beep
8
7
6
5
4
3
2
1
Reserved
Restore
Siren / Comm
Dialer Delay
Twin Trip
Trouble
DEOL Tamper
Reserved
Segment 3
16
16
16
16
8
7
6
5
4
3
2
1
Segment 1
(Zone 49)
8
7
6
5
4
3
2
1
Segment 2
(Zone 50)
8
7
6
5
4
3
2
1
Segment 3
(Zone 51)
Zone 49-56 Area Selection
16
8
7
6
5
4
3
2
1
Segment 4
(Zone 52)
16
Zone 49-56 Configuration Groups
Local only
Reserved
Delay 2
Delay 1
Follower
Key-switch
24 hour
Fire
Area 1
120
Feat.
16
119
Feat.
8
7
6
5
4
3
2
1
Segment 2
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Segment 6
(Zone 54)
Reserved
Reserved
Reserved
Reserved
Access Control
Request to Exit
Resistor Defeat
Zone Activity
Segment 5
(Zone 53)
8
7
6
5
4
3
2
1
Segment 4
Configuration Group 20 - Characteristic Select
Configuration Group 20 - Alarm Event Code
Segment 1
106
Feat.
3
105
Feat.
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Segment 8
(Zone 56)
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Segment 7
(Zone 55)
8
7
6
5
4
3
2
1
Segment 5
51
Pg
51
Pg
51
Pg
51
Pg
16
16
16
2
3
4
5
6
7
8
2
3
4
5
6
7
8
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
16
16
16
16
Segment 2
(Zone 66)
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
8
7
6
5
4
3
2
1
Segment 3
(Zone 67)
Zone 65-72 Area Selection
16
Segment 1
(Zone 65)
124
Feat.
16
123
8
7
6
5
4
3
2
1
Segment 3
(Zone 59)
8
7
6
5
4
3
2
1
Segment 4
(Zone 60)
16
8
7
6
5
4
3
2
1
Segment 4
(Zone 68)
16
Zone 65-72 Configuration Groups
1
1
Area 1
Feat.
16
Zone 57-64 Area Selection
16
Segment 2
(Zone 58)
16
16
Zone 57-64 Configuration Groups
Segment 1
(Zone 57)
122
Feat.
16
121
Feat.
8
7
6
5
4
3
2
1
Segment 5
(Zone 69)
8
7
6
5
4
3
2
1
Segment 5
(Zone 61)
8
7
6
5
4
3
2
1
Segment 6
(Zone 70)
8
7
6
5
4
3
2
1
Segment 6
(Zone 62)
8
7
6
5
4
3
2
1
Segment 7
(Zone 71)
8
7
6
5
4
3
2
1
Segment 7
(Zone 63)
8
7
6
5
4
3
2
1
Segment 8
(Zone 72)
8
7
6
5
4
3
2
1
Segment 8
(Zone 64)
51
Pg
51
Pg
51
Pg
51
Pg
Area 8
Area 7
Area 6
Area 5
Area 4
Area 3
Area 2
Area 1
128
Feat.
16
127
Feat.
Area 8
Area 7
Area 6
Area 5
Area 4
Area 3
Area 2
Area 1
126
Feat.
16
125
Feat.
16
16
16
16
16
16
8
7
6
5
4
3
2
1
Segment 2
(Zone 74)
8
7
6
5
4
3
2
1
Segment 3
(Zone 75)
8
7
6
5
4
3
2
1
Segment 4
(Zone 76)
16
16
16
16
16
8
7
6
5
4
3
2
1
Segment 1
(Zone 81)
8
7
6
5
4
3
2
1
Segment 2
(Zone 82)
8
7
6
5
4
3
2
1
Segment 3
(Zone 83)
Zone 81-88 Area Selection
16
8
7
6
5
4
3
2
1
Segment 4
(Zone 84)
16
Zone 81-88 Configuration Groups
8
7
6
5
4
3
2
1
Segment 1
(Zone 73)
Zone 73-80 Area Selection
16
Zone 73-80 Configuration Groups
8
7
6
5
4
3
2
1
Segment 5
(Zone 85)
8
7
6
5
4
3
2
1
Segment 5
(Zone 77)
8
7
6
5
4
3
2
1
Segment 6
(Zone 86)
8
7
6
5
4
3
2
1
Segment 6
(Zone 78)
8
7
6
5
4
3
2
1
Segment 7
(Zone 87)
8
7
6
5
4
3
2
1
Segment 7
(Zone 79)
8
7
6
5
4
3
2
1
Segment 8
(Zone 88)
8
7
6
5
4
3
2
1
Segment 8
(Zone 80)
52
Pg
52
Pg
52
Pg
52
Pg
16
16
16
2
3
4
5
6
7
8
2
3
4
5
6
7
8
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
16
16
16
16
Segment 2
(Zone 98)
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
8
7
6
5
4
3
2
1
Segment 3
(Zone 99)
Zone 97-104 Area Selection
16
Segment 1
(Zone 97)
132
Feat.
16
131
8
7
6
5
4
3
2
1
Segment 3
(Zone 91)
8
7
6
5
4
3
2
1
Segment 4
(Zone 92)
16
8
7
6
5
4
3
2
1
Segment 4
(Zone 100)
16
8
7
6
5
4
3
2
1
Segment 5
(Zone 101)
8
7
6
5
4
3
2
1
Segment 5
(Zone 93)
Zone 97-104 Configuration Groups
1
1
Area 1
Feat.
16
Zone 89-96 Area Selection
16
Segment 2
(Zone 90)
16
16
Zone 89-96 Configuration Groups
Segment 1
(Zone 89)
130
Feat.
16
129
Feat.
8
7
6
5
4
3
2
1
Segment 6
(Zone 102)
8
7
6
5
4
3
2
1
Segment 6
(Zone 94)
8
7
6
5
4
3
2
1
Segment 7
(Zone 103)
8
7
6
5
4
3
2
1
Segment 7
(Zone 95)
8
7
6
5
4
3
2
1
Segment 8
(Zone 104)
8
7
6
5
4
3
2
1
Segment 8
(Zone 96)
52
Pg
52
Pg
52
Pg
52
Pg
Area 8
Area 7
Area 6
Area 5
Area 4
Area 3
Area 2
Area 1
136
Feat.
16
135
Feat.
Area 8
Area 7
Area 6
Area 5
Area 4
Area 3
Area 2
Area 1
134
Feat.
16
133
Feat.
16
16
16
16
16
16
8
7
6
5
4
3
2
1
Segment 2
(Zone 106)
8
7
6
5
4
3
2
1
Segment 3
(Zone 107)
8
7
6
5
4
3
2
1
Segment 4
(Zone 108)
16
16
16
16
16
8
7
6
5
4
3
2
1
Segment 1
(Zone 113)
8
7
6
5
4
3
2
1
Segment 2
(Zone 114)
8
7
6
5
4
3
2
1
Segment 3
(Zone 115)
16
8
7
6
5
4
3
2
1
Segment 4
(Zone 116)
Zone 113-120 Area Selection
16
8
7
6
5
4
3
2
1
Segment 5
(Zone 117)
8
7
6
5
4
3
2
1
Segment 5
(Zone 109)
Zone 113-120 Configuration Groups
8
7
6
5
4
3
2
1
Segment 1
(Zone 105)
Zone 105-112 Area Selection
16
Zone 105-112 Configuration Groups
8
7
6
5
4
3
2
1
Segment 6
(Zone 118)
8
7
6
5
4
3
2
1
Segment 6
(Zone 110)
8
7
6
5
4
3
2
1
Segment 7
(Zone 119)
8
7
6
5
4
3
2
1
Segment 7
(Zone 111)
8
7
6
5
4
3
2
1
Segment 8
(Zone 120)
8
7
6
5
4
3
2
1
Segment 8
(Zone 112)
53
Pg
53
Pg
53
Pg
53
Pg
16
16
16
2
3
4
5
6
7
8
2
3
4
5
6
7
8
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8
Tue
Wed
Thur
Fri
Sat
Reserved
3
4
5
6
7
8
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
0
Programming Sheets v1.0.11
Segment 1
162
8
7
6
5
4
3
2
1
Segment 2
(Area 2)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 3
(Area 3)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 4
(Area 4)
8
7
6
5
4
3
2
1
Segment 4
(Zone 124)
8
7
6
5
4
3
2
1
Segment 5
(Zone 125)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 5
(Area 5)
0=3k3, 1=1k5, 2=2k2, 3=3k9, 4=4k7, 5=5k6, 6=6k8
EOL Resistor Value Select
Mon
2
Feat.
Sun
1
Segment 1
(Area 1)
155
8
7
6
5
4
3
2
1
Segment 3
(Zone 123)
16
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 6
(Area 6)
8
7
6
5
4
3
2
1
Segment 6
(Zone 126)
Days of the Week for Auto Disarm Areas 1-8
1
1
Area 1
Feat.
16
Zone 121-128 Area Selection
16
Segment 2
(Zone 122)
16
Zone 121-128 Configuration Groups
Segment 1
(Zone 121)
138
Feat.
16
137
Feat.
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 7
(Area 7)
8
7
6
5
4
3
2
1
Segment 7
(Zone 127)
8
7
6
5
4
3
2
1
Reserved
Sat
Fri
Thur
Wed
Tue
Mon
Sun
Segment 8
(Area 8)
8
7
6
5
4
3
2
1
Segment 8
(Zone 128)
54
Pg
54
Pg
53
Pg
53
Pg
Notes
Notes
Notes
Notes
Hills Reliance Specifications
Operating Power
16.5 VAC 25, 40, or 50 VA Transformer
Auxiliary Power
W/ 25 VA Transformer
W/ 40 or 50 VA
Transformer
W/ NX-320 Power Supply
12 VDC Regulated 500 mA
12 VDC Regulated 1 Amp
12 VDC Regulated 3.5 Amps
Loop Resistance
Standard Loop
300 Ohms Maximum
2-Wire Smokes
30 Ohms Maximum
4-Wire Smokes
300 Ohms Maximum
Loop Response
500mS
Built-in Siren Driver
3-tone (Steady, Yelp, Evacuation)
Operating Temperature
0 to 48 degrees C
LED Code Pad Dimensions
16.25cm Wide
10.15cm High
2.8cm Deep
LCD Code Pad Dimensions
16.25cm Wide
13.45cm High
2.50cm Deep
Metal Enclosure Dimension
28.60cm Wide
28.60cm High
8.90cm Deep
Shipping Weight
4 kg
N4131
© 2009 Hills Industries
Warranty Statement
Hills Industries guarantees this product against defective parts and workmanship for twenty-four (24)
months from date of purchase. If any defect appears during the warranty period return it to place of
purchase. Hills Industries assumes no liability for consequential or indirect damage and accepts no
responsibility for repairing damage to the product caused by misuse, careless handling, or where
repairs have been made by others.
No other guarantee, written or verbal, is authorized by or on behalf of Hills Industries.
Hills Industries
12 Wiggs Rd Riverwood
NSW 2210 Australia
Phone (02) 9717 5222
Quick Start Guide
Short form programming sheet for a monitored system
This is not a substitute for reading the manual
1. Hard Default Panel
2. Go To Program Mode
3. Soft Default Panel
Unplug battery & remove power, turn on power,
Enter 971300 within 10 seconds,
Wait 12 seconds
Repeat
*8 9713 0#
910#, Exit, Exit, [Chime], wait 12 seconds
4. Go To Program Mode
5. Change Program Code
6. Duress Code
*8 9713 0#
1# n*n*n*n* #
3# n*n*n*n* #
7.
8.
9.
10.
11.
12.
13.
14.
4# n*n*n*n*n*n*n*n* #
5# n*n*n*n* #
6# 1* (1 for CID, or 3 for Domestic Dial)
7# n*n*n*n*n*n*n*n* #
9# 3 7 *# (for open/close, tamper/restore)
11# n*
12# n*n*n*n*n*n*n*n*
14# 1* (to enable two call AMD)
Receiver Phone #1
System Account Code
Communication Format
Receiver Phone #2
Report Event Summary
Phone Cut Delay
Download Access Code
Download Control (Remote Access)
15. Force Arm Globally
16# 3*#
16. Entry/Exit Time #1 & #2
17# nn*nn*nn*nn* #
17. Configuration Groups (Zone Types)
18# (zones 1-8), 20# (zones 9-16),
59# (zones 17-24), 61# (zones 25-32),
63# (zones 33-40), 65# (zones 41-48),
119# (zones 49-56), 121# (zones 57-64)
18. System Options
19. Medical Alarm Sounder “ON”
20. Auto Test Control
22# 7*7* # (for siren on tamper and
[*][44] manual communicator test enable)
24# 7* (enable code pad beeping)
32# (see Feature 32 for details)
21. Exit Program Mode
Press Exit, Exit, [Chime] wait 12 seconds
22. Change Master Code (default 1234)
23. Program User Codes
[*5] [Master Code] [01] [New Code] #
[*5] [Master Code] [User] [User Code] #
24. Set Date & Time (at User Level)
Set System Calendar
Set System Clock
25. Walk Test
End Walk Test
[*][9][6] [Master Code] [Day of Week]
[Month] [Day of Month] [Year]
[*][9][7] [Master Code] [Hour] [Minutes]
* [Chime] [Master Code]
[Master Code]
26. Train Client/End User
Note if testing reporting, master code does not send open/closing reports by default (see Feature 2)
Reliance 128 Installation Manual v1-1.doc