GP1UM26RK0VF/GP1UM27RK0VF Series GP1UM28RK0VF

GP1UM26RK0VF/GP1UM27RK0VF Series
GP1UM28RK0VF/GP1UM28QK0VF Series
GP1UM26RK0VF/GP1UM27RK0VF Series
GP1UM28RK0VF/GP1UM28QK0VF Series
Anti Electromagnetic Induction
Noise Type,Compact IR Detecting Unit
for Remote Control
■ Features
■ Applications
1. AV equipments
2. Home appliances
1. Anti electomagnetic induction noise type.
2. Compact (case volume).
3. Various B.P.F. (Band-Pass Filter) frequency to meetdifferent user needs.
■ Outline Dimens ions
(Unit : mm)
GP1UM26RK0VF Series
GP1UM27RK0VF Series
1.25
9.6
0.4
*1
3.6
0.5
*3
2.9
*2
1.4
13.8
9.6
*1
7.6
3.6
0.4
5.8
2.9
2.54
3.6
0.5
0.5
1.4
3
2.54
2
1
2.54
3-
Example of mounting drawing
from solder side (Reference)
φ
0.
8
0.8
*3
0.8
*3
0.5
1.*1 : Indicates root dimensions of connector.
2.Unspecified tolerance : ±0.3
3.Case thickness : 0.3TYP
4.*2 : Exclude sagged solder
5.*3 : If there are difficulties to insert the GP1UM26RK0VF series on PCB,
we recommend to expand 0.1mm from original 2.9mm.
*1
1
2
2.54
*1
2.54
3
1 V OUT
2 VCC
3 G ND
5.8
*3
2.9
1.4
3
2.54
2
2.9
1.4
1.7
C enter
of P D
C enter
of P D
5.85
7.55
6.7
*1
*3
*3
1.7
2.54
1 V OUT
2 VCC
3 G ND
7.55
6.7
*1
3
4.3 2.9
4.7
2
1.7
1
0.5
Example of mounting drawing
from solder side (Reference)
5.85
0.7
1.7
0.7
10.2
2.2
5.6
0.5
1.4
2.2
0.5
1.4
8.6
1.25
*1
1.4
7.6
4.3 2.9
4.7
3.6
0.5
1.4
2.2
5
2.2
5.6
1
3φ
2.54
0.
8
1.*1 : Indicates root dimensions of connector.
2.Unspecified tolerance : ±0.3
3.Case thickness : 0.3TYP
4.*2 : Exclude sagged solder
5.*3 : If there are difficulties to insert the GP1UM27RK0VF series on PCB,
we recommend to expand 0.1mm from original 2.9mm.
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: OP06010
1
GP1UM26RK0VF/GP1UM27RK0VF Series
GP1UM28RK0VF/GP1UM28QK0VF Series
■ Outline Dimensions
(Unit : mm)
GP1UM28RK0VF Series
2.75
2.2
9.6
*2
4.3
2.9
5.6
1.25
9.6
1.25
GP1UM28QK0VF Series
0.8
3.6
*2
17.8
9.6
*1
0.4
1.4
7.6
4.3 2.9
4.7
14.2
2.54
2.54
0.5
1.4
2.2
2.2
3.6
1.25
1.25
0.5
0.8
*1
*1
5.6
3
1 VOUT
2 VCC
3 GND
2.54
0.5
2.54
1
2.54
2
3
*1
2.54
1 VOUT
2 VCC
3 GND
*3
2.54
3.55
*3
*3
2.9
5.8
Center
of PD
1
1.4
*3
1.4
2
1.4
2.9
2.9
1.4
3
Top of lenz
3
1.7
2
5.8
2.9
3-
5.85
1
7.55
6.7
0.5
*1
1.7
*3
1.7
Example of mounting drawing
from solder side (Reference)
*3
1.4
Example of mounting drawing
from solder side (Reference)
0.8
0.8
1.4
5.4
6.8
3-φ
0.8
3.6
1.7
3.7
3.9
2
1.85
1
1.7
0.5
0.4
*1
φ
0.
8
1.*1 : Indicates root dimensions of connector.
2.Unspecified tolerance : ±0.3
3.Case thickness : 0.3TYP
4.*2 : Exclude sagged solder
5.*3 : If there are difficulties to insert the GP1UM28QK0VF series on PCB,
we recommend to expand 0.1mm from original 2.9mm.
2.54
1.*1 : Indicates root dimensions of connector.
2.Unspecified tolerance : ±0.3
3.Case thickness : 0.3TYP
4.*2 : Exclude sagged solder
5.*3 : If there are difficulties to insert the GP1UM28RK0VF series on PCB,
we recommend to expand 0.1mm from original 2.9mm.
■ Model Line-up
Diversified models with a different B.P.F. frequency are also available.
Model No.
B.P.F. center frequency
40
GP1UM28RK0VF
GP1UM26RK0VF
GP1UM27RK0VF
36
GP1UM260RKVF
GP1UM270RKVF
GP1UM280RKVF
38
GP1UM281RKVF
GP1UM261RKVF
GP1UM271RKVF
36.7
GP1UM262RKVF
GP1UM272RKVF
GP1UM282RKVF
32.75
GP1UM263RKVF
GP1UM273RKVF
GP1UM283RKVF
56.8
GP1UM267RKVF
GP1UM277RKVF
GP1UM287RKVF
Unit
GP1UM28QK0VF
GP1UM280QKVF
GP1UM281QKVF
GP1UM282QKVF
GP1UM283QKVF
GP1UM287QKVF
kHz
Sheet No.: OP06010
2
GP1UM26RK0VF/GP1UM27RK0VF Series
GP1UM28RK0VF/GP1UM28QK0VF Series
■ Internal Block Diagram
RL
VOUT
B.P.F. Demodulator Integrator Comparator
Limiter
VCC
GND
■ Absolute Maximum Ratings
Parameter
Symbol
Supply voltage
V CC
*1
Operating temperature
Topr
Storage temperature
Tstg
*2
Soldering temperature
Tsol
■ Recommended Operating Conditions
(Ta=25℃)
Rating
Unit
V
0 to +6.0
℃
-10 to +70
-20 to +70
℃
260
℃
Parameter
Supply voltage
Symbol
V CC
Operating conditions
4.5 to 5.5
Unit
V
*1 No dew condensation is allowed
*2 For 5s (At mounting on PCB with thickness of 1.6mm)
■Electro-optical Characteristics
Parameter
Dissipation current
High level output voltage
Low level output voltage
High level pulse width
Low level pulse width
B.P.F. center frequency
Output pull-up resistance
(Ta=25℃, VCC=5V)
MIN.
Symbol
Conditions
I CC
V OH
V OL
T1
T2
f0
RL
No input light
-
*3
VCC-0.5
*3
IOL=1.6mA
*3
600
400
*3
-
TYP.
0.5
-
MAX.
Unit
0.6(0.65)*4 mA
0.45
1200
1000
-
*5
-
70
100
130
V
V
μs
μs
kHz
kΩ
*3 The burst wave as shown in the following figure shall be transmitted by the transmitter shown in Fig. 1
The carrier frequency of the transmitter, however, shall be same as *5, and measurement shall be from just after starting the transmission until 50 pulse
*4 In case of B.P.F. center frequency f0 :56.8kHz model
*5 The B.P.F. center frequency f0 varies with model, as shown in ■Model Line-up
B urs t wave
600μs
1000μs
f0=(*5)
Duty 50%
Sheet No.: OP06010
3
GP1UM26RK0VF/GP1UM27RK0VF Series
GP1UM28RK0VF/GP1UM28QK0VF Series
■ Performance
Using the transmitter shown in Fig. 1, the output signal of the light detecting unit is good enough to meet the following items in the
standard optical system in Fig. 2.
1. Linear reception distance characteristics
When L=0.2 to 8.5(7.0)*6m, *7EV<10 lx and φ=0°in Fig.2, the output signal shall meet the electrical characteristics in the attached list.
2.Sensitivity angle reception distance characteristics
When L=0.2 to 6.0(4.5)*6m, *7EV<10 lx and φ≦30°in Fig.2, the output signal shall meet the electrical characteristics in the attached list.
3.Anti outer peripheral light reception distance characteristics
When L=0.2 to 4.0(3.0)*6m, *7*8EV≦300 lx and φ=0°in Fig.2, the output signal shall meet the electrical characteristics in the attached list.
*6 In case of B.P.F. center frequency f0 :56.8kHz model
*7 It refers to detector face illuminance
*8 Outer peripheral light source: CIE standard light source A shall be used and placed at 45°from perpendicular axis at the detector face center
Fig.1 Transmitter
20cm
10kΩ
Transmitter (GL521 used)
f0 (* 5)
Duty 50%
5V
10μF
PD49PI
10kΩ
VOUT
Oscilloscope
In the above figure, the transmitter should be set so that the output VOUT (P-P) can be 40mV.
However, the PD49PI to be used here should be of the short-circuit current ISC=2.6μA at EV =100 lx.
(EV is an illuminance by CIE standard light source A (tungsten lamp).)
Fig.2 Standard Optical System
Light detector face illuminance:EV
VOUT
Reception distance:L
Transmitter
( φindicates horizontal and vertical directions.)
Sheet No.: OP06010
4
GP1UM26RK0VF/GP1UM27RK0VF Series
GP1UM28RK0VF/GP1UM28QK0VF Series
■ Precautions for Operation
1. When this infrared remote control detecting unit shall be adopted for wireless remote control, please use the following signal format .
(NEC code,RC-6code etc.)
n
・Total duty ratio Dt (Emitting time t
Σ N / Transmitting time for 1 block T) : 40% or less.
N=1
・ON signal time TON:200μs or more.
Transmitting time for 1 block:T
TON
t1
t2
t3
tn
n
Dt =(Σ tN /T)×100 (%)
N=1
In case the signal format of total duty and/or ON/OFF signal time dosen`t meet the conditions noted above, there is a
case that reception distance much reduces or output dose not appear.
2. Use the light emitting unit (remote control transmitter), in consideration of performance, characteristics, operating conditions of
light emitting device and the characteristics of the light detecting unit.
3. Pay attention to a malfunction of the light detecting unit when the surface is stained with dust and refuse.
Care must be taken not to touch the light detector surface.
If it should be dirty, wipe off such dust and refuse with soft cloth so as to prevent scratch. In case some solvents are required, use
methyl alcohol, ethyl alcohol or isopropyl alcohol only.
Also, protect the light detecting unit against flux and others, since their deposition on the unit inside causes reduction of the
function, fading of markings such as the part number.
4. The shield case should be grounded on PCB pattern.
(The area across the shield case and the GND terminal is internally non-conductive.)
5. Do not apply unnecessary force to the terminal and the case.
6. Do not push the light detector surface (photodiode) from outside.
7. To avoid the electrostatic breakdown of IC, handle the unit under the condition of grounding with human body, soldering iron, etc.
8. Do not use hole and groove set in the case of the light detecting unit for other purposes, since they are required to maintain the
specified performance.
9. External Circuit Examples (Mount the outer parts as near the unit as possible).
GND
VCC
CO
+
GND
R1
Ve
VOUT
VO
(Circuit parameters)
R1=47Ω±5%
C1=47μF
In setting R1 and C1, use suitable values after considering under the real condition
The circuit constant is a example. It is difference from mounting equipment. Please select it by your mounting equipment.
This device has a transistor as protection element between VCC and GND to improve anti-static electricity proof.
Please be carefully not to apply exceeding the absolute maximum ratings of applying voltage and continuous high voltage spike
noise because there is cases that transistor will be short by secondary breakdown generally. In order to do difficultly, Please add CR
filter(47Ω(1/10W), 10μF or more)such as external circuit example above near VCC.
Sheet No.: OP06010
5
GP1UM26RK0VF/GP1UM27RK0VF Series
GP1UM28RK0VF/GP1UM28QK0VF Series
10. There is a possibility that noise on output may be caused by environmental condition (Disturbing light noise, Electromagnetic
noise, Power supply line noise, etc.) even if there is no input transmission signal.
11. Please shall confirm operation or your actual machine. Because the output pulse width of this product is fluctuated by
environmental conditions such as signal format, temperature, distance from transmitter, and so on.
12. In case that this product is kept in high humidity condition, it may be hard to solder, please be careful enough about storage
method.
Depend on the flux you select, there are different solderabilities, so please select a suitable flux and use it.
13. This product dose`t correspond to soldering by reflow.
14. Please use this device away from the dew drop.
Be aware that the dew drop rusts shield case and others, may affect the electric characteristics.
Sheet No.: OP06010
6