Bayliner Capri 19' Specifications

Hull Identification Number: _____________________________________________
Engine Serial Number: _________________________________________________
The Hull Identification Number (HIN) is located on the starboard side of the transom. Be sure to
record the HIN in the space provided above and always refer to the HIN for all correspondence or
orders.
TYPICAL HIN LOCATION
STARBOARD TRANSOM
BOARDING LADDER
© 2001 Bayliner Technical Publications. All rights reserved.
No part of this publication may be reproduced, stored in any retrieval system, or transmitted in
any form by any means, electronic, mechanical, photocopying, recording or otherwise, without
prior written permission of Bayliner. Printed in the United States of America.
Proprietary Rights
This document discloses subject matter in which Bayliner has proprietary rights. The information
and design disclosed herein were originated by and are the property of Bayliner. Neither receipt
nor possession thereof confers or transfers any right to reproduce, copy, alter or disclose the document or any part thereof, any information contained therein, or to construct boats or any item from
it, except by written permission from or written agreement with Bayliner. This document is to be
returned upon request to Bayliner.
General Notes
The material in this document is for information only and is subject to change without notice.
While reasonable efforts have been made in the preparation of this document to assure its accuracy, Bayliner assumes no liability resulting from errors or omissions in this document, or from
the use of information contained herein.
Due to our commitment to product improvement, Bayliner reserves the right to make changes in
the product design, specifications, and equipment at any time without notice or obligation. Illustrations and/or photos may show optional equipment.
All Bayliner products meet or exceed USCG (Unites States Coast Guard) and/or NMMA
(National Marine Manufacturer’s Association) construction standards. Manufactured with 1,1,1
Trichloroethane, a substance which harms public health and environment during the manufacturing process by destroying ozone in the upper atmosphere.
CONTENTS
CHAPTER 1: ABOUT THIS MANUAL
1
1
2
2
3
3
4
5
Dealer Service
Boating Experience
Engine & Accessories Guidelines
Qualified Maintenance
Special Care For Moored Boats
Safety Standards
Hazard Warning Symbols
Carbon Monoxide (CO)
5
6
6
Sources of CO
Carbon Monoxide Alarm System
What To Do If Carbon Monoxide Is Detected
CHAPTER 2: PRODUCT SPECIFICATIONS
7
7
8
8
9
9
10
10
11
11
12
12
13
1600 (CF)
1750 (BE)
1800 (CJ)
1804 (PC)
1850 (BH)
1850 (CB)
1950 (BT)
1950 (BU)
1952 (BV)
1952 (BW)
1950 (CL)
1952 (CN)
1954 (CW)
CHAPTER 3: COMPONENTS/SYSTEMS
14
15
16
18
18
18
19
Electrical System (12Volt DC)
Fuses and/or Circuit Breakers
Dash Programming (1952BV only)
Controls
Navigation and Interior Lights
Compass
Depth Finder
19
20
20
20
21
22
23
Bow Mount For Trolling Motor-1804PC and 1954CW
Anchoring
Ski Tow Ring
Ski Pylon (outboard models)
Hull Exterior Drains & Hardware
Quick Oil Drain System
Fuel System
23
23
24
25
26
28
Bilge Blower
Live Well System
Bilge Pump
Jump Seat to Sunlounge Conversion
28
29
31
Models, 1950CL,1952CN, and 1954CW
Models, 1750BE, 1850BH, 1950BT and 1952BV
Sleeper Seat Adjustment
31
31
32
33
34
Fuel Fills and Vents
Fuel Filters
Operating Positions:
Lounge positions:
Removable Fishing Seats (1804PC and 1954CW)
Canvas Top (Option) Installation
Canvas Stowage
CHAPTER 4: WIRING DIAGRAMS
35
36
37
38
1600CF and 1800CJ
1804PC
1750BE, 1850BH/CB, 1950BT/BU and 1952BV/BW
1950CL, 1952CN and 1954CW
APPENDIX A: BAYLINER CAPRI LIMITED WARRANTY
39
39
39
39
39
39
39
Limited Lifetime Structural Hull Warranty
One Year Parts and Components Limited Warranty
Six Month Cosmetic Gelcoat Defect Limited Warranty
What Is Not Covered
Other Limitations
Your Obligations
Transferability
1
CHAPTER 1: ABOUT THIS MANUAL
This Owner’s Manual Supplement provides specific information about your boat
that is not covered in the Sport Boat Owner’s Manual. Study the Sport Boat
Owner’s Manual and this supplement carefully. Pay particular attention to
APPENDIX A: BAYLINER CAPRI LIMITED WARRANTY in this supplement.
Keep the Sport Boat Owner’s Manual and this supplement on your boat in a secure,
yet readily available place.
Dealer Service
Make sure you receive a full explanation of all systems from the selling dealer
before taking delivery of your boat. Your selling dealer is your key to service. If
you experience any problems with your new boat, immediately contact the selling
dealer. If for any reason your selling dealer is unable to help, you can call us direct
on our customer service hotline: 360-435-8957 or send us a FAX: 360-403-4235.
Boating Experience
If this is your first boat or if you are changing to a type of boat you are not familiar
with, for your own comfort and safety, you must obtain handling and operating
experience before assuming command of the boat.
Take one of the boating safety classes offered by the U.S. Power Squadrons or the
U.S. Coast Guard Auxiliary. For more course information, including dates and
locations of upcoming classes, contact the organizations directly:
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet
at: http://www.usps.org
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at:
http://www.cgaux.org
Outside the United States, your selling dealer, national sailing federation or local
yacht club can advise you of local sea schools or competent instructors.
!
WARNING!
CONTROL HAZARD! A qualified operator must be in control of the boat at all
times. DO NOT use your boat while under the influence of alcohol or drugs.
Capri 16’ - 19’ • Owner’s Manual Supplement
2
CHAPTER 1: ABOUT THIS MANUAL
Engine & Accessories Guidelines
Your boat’s engine and accessories were selected to provide optimum performance
and service. Installing different engines or other accessories may cause unwanted
handling traits. Should you choose to install a different engine or to add accessories
that will affect the boat’s running trim, have an experienced marine technician perform a safety inspection and handling test before using your boat again.
Be advised that certain modifications to your boat can result in cancellation of your
warranty protection. Check with your dealer before making any modifications to
your boat.
The engine and accessories installed on your boat come with their own operation
and maintenance manuals. Read and understand these manuals before operating the
engines and accessories.
NOTICE
When storing your boat please refer to your engine’s operation and maintenance manuals.
Qualified Maintenance
!
WARNING!
To maintain the integrity and safety of your boat, only qualified people should
perform maintenance on, or in any way modify: The steering system, propulsion system, engine control system, fuel system, environmental control system,
or electrical system.
Failure to maintain your boat’s systems as designed could violate the laws in your
jurisdiction and could expose you and other people to the danger of bodily injury or
accidental death. Follow the instructions provided in the Sport Boat Owner’s Manual, this Owner’s Manual Supplement, the engine owner’s manual and all accessory
instruction sheets/manuals included in your boat’s owner’s packet.
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 1: ABOUT THIS MANUAL
3
Special Care For Moored Boats
If moored in saltwater or fresh water, your boat will collect marine growth on its
hull bottom. This will detract from the boat’s beauty, greatly affect its performance
and may damage the gelcoat.
Periodically haul the boat out of the water and scrub the hull bottom with a bristle
brush and a solution of soap and water.
NOTICE
To help seal the hull bottom and reduce the possibility of gelcoat blistering on
moored boats, apply an epoxy barrier coating, such as INTERLUX, Interprotect
2000E/2001E. Cover the barrier coating with several coats of anti-fouling paint.
Many states regulate the chemical content of bottom paints. Ask your local
dealer about the laws in effect in your area.
Safety Standards
Your boat’s mechanical and electrical systems were designed to meet safety standards in effect at the time it was constructed. Some of these standards were mandated by law. All of them were designed to insure your safety, and the safety of
other people, vessels and property.
In addition to this supplement, read the Sport Boat Owner’s Manual, warning labels,
and all literature in your owner’s packet for important safety standards and hazard
information.
!
DANGER!
DANGER
PERSONAL SAFETY HAZARD! DO NOT allow anyone to ride on
parts of the boat not designated for such use.
Sitting on seat backs, lounging on the forward deck, bow riding, gunwale riding
or occupying the transom platform or the aft sunlounge cushions while underway is especially hazardous and WILL cause personal injury or death.
!
DANGER!
DANGER
PERSONAL SAFETY HAZARD! Always secure the anchor and other loose
objects before getting underway. The anchor and other items that are not
properly secured can come loose when the boat is moving and cause personal
injury or death.
Capri 16’ - 19’ • Owner’s Manual Supplement
4
CHAPTER 1: ABOUT THIS MANUAL
Hazard Warning Symbols
The hazard warning symbols shown below are used throughout this supplement to
call attention to potentially dangerous situations that could lead to either personal
injury or product damage. Read these warnings and follow all safety instructions
.
HOT
HAZARD!
FIRE
HAZARD!
PERSONAL INJURY
& FALLING HAZARD!
ROTATING
PROPELLER HAZARD!
EXPLOSION
HAZARD!
OPEN FLAME
HAZARD!
ELECTRICAL
HAZARD!
CO POISONING
HAZARD!
!
DANGER!
This message box alerts you to immediate hazards which WILL cause severe
personal injury or death if the warning is ignored.
! WARNING!
This message box alerts you to hazards or unsafe practices which COULD
result in severe personal injury or death if the warning is ignored.
! CAUTION!
This message box alerts you to hazards or unsafe practices which COULD
result in minor personal injury or cause product or property damage if the
warning is ignored.
NOTICE
This message box calls attention to installation, operation or maintenance
information, which is important to proper operation but is not hazard related.
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 1: ABOUT THIS MANUAL
5
Carbon Monoxide (CO)
!
DANGER!
CARBON MONOXIDE POISONING HAZARD! Carbon monoxide
gas (CO) is colorless, odorless, and extremely dangerous. All
engines, generators, and fuel burning appliances produce CO as
exhaust. Direct and prolonged exposure to CO will cause BRAIN
DAMAGE or DEATH. Signs of CO poisoning include headache,
nausea, dizziness, and drowsiness.
CO poisoning causes a significant number of boating deaths each year. Called the
"silent killer", CO is an extremely toxic, colorless, odorless and tasteless gas.
Breathing CO blocks the ability of your blood to carry oxygen. The effects are
cumulative, even low levels of exposure can result in injury or death.
Sources of CO
Sources of CO include:
a. Using the engine or generator
when the boat is moored in a
confined space.
b. Mooring close to another boat that
is running its engine, generator, or
any other CO source.
c. Running the boat with the trim
angle of the bow too high.
d. Running the boat without through
ventilation (station wagon effect).
To correct stationary situations a and/or b:
• Close all windows, portlights and hatches.
• If possible, move your boat away from the source of the CO.
To correct running situations c and/or d:
• Trim the bow down.
• Open windows and canvas.
• When possible, run the boat so that the prevailing winds will help dissipate the
exhaust.
IMMEDIATELY take corrective action when CO is detected (see, Carbon
Monoxide Alarm System, on the next page).
Capri 16’ - 19’ • Owner’s Manual Supplement
6
CHAPTER 1: ABOUT THIS MANUAL
Factors increasing the effects of CO include:
• Age.
• Smokers or people exposed to high concentrations of cigarette smoke.
• Consumption of alcohol.
• Lung disorders, heart problems, and pregnancy.
Carbon Monoxide Alarm System
Your boat may feature a carbon
monoxide (CO) alarm system. DO
NOT DISCONNECT THE
ALARM SYSTEM. Read and
understand the manufacturer’s
instructions for your CO alarm
system. If you did not receive an
instruction manual, call (800) 3830269 and one will be mailed to
you. If your boat is not equipped
with a carbon monoxide alarm,
consider purchasing one from your
dealer or marine supply store.
MARINE TECHNOLOGIES INC.
CARBON MONOXIDE ALARM MODEL 60-541
(REPLACE AFTER TEN YEARS OF USE)
What To Do If Carbon Monoxide Is Detected
• Immediately ventilate any enclosed spaces that are occupied by people and reset
your CO alarm.
• Immediately move anyone showing any symptoms of CO poisoning into fresh
air. See a doctor if any symptoms persist. If the person is unconscious, immediately administer oxygen or CPR and call for emergency help.
Capri 16’ - 19’ • Owner’s Manual Supplement
7
CHAPTER 2: PRODUCT SPECIFICATIONS
1600 (CF)
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
16' 2''
3' 5''
7' 2''
2' 7''
18
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
17' 7''
3' 10''
6' 11''
2' 8''
23
1750 (BE)
Capri 16’ - 19’ • Owner’s Manual Supplement
8
CHAPTER 2: PRODUCT SPECIFICATIONS
1800 (CJ)
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
18' 0''
3' 10''
7' 6''
2' 8''
23
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
17' 7''
3' 10''
7' 6''
2' 7''
23
1804 (PC)
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 2: PRODUCT SPECIFICATIONS
9
1850 (BH)
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal.
18' 0''
3' 10''
7' 6''
2' 10''
23
1850 (CB)
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
18' 0''
3' 10''
7' 6''
2' 10''
23
Capri 16’ - 19’ • Owner’s Manual Supplement
10
CHAPTER 2: PRODUCT SPECIFICATIONS
1950 (BT)
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
18' 10''
3' 10''
7' 10''
2' 10''
35
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
18' 10''
3' 10''
7' 10''
3' 10''
35
1950 (BU)
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 2: PRODUCT SPECIFICATIONS
11
1952 (BV)
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
19' 3''
4' 4''
7' 10''
2' 11''
35
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
19' 3''
4' 4''
7' 10''
2' 11''
35
1952 (BW)
Capri 16’ - 19’ • Owner’s Manual Supplement
12
CHAPTER 2: PRODUCT SPECIFICATIONS
1950 (CL)
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
18' 9''
3' 1''
7' 7''
2' 10''
23
1952 (CN)
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
18' 8''
3' 8''
7' 6''
2' 10''
23
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 2: PRODUCT SPECIFICATIONS
13
1954 (CW)
Overall
Length
Bridge
Clearance
Beam
Maximum
Draft
Fuel Tank
Capacity (gal)
18' 9''
3' 1''
7' 7''
2' 10''
23
Capri 16’ - 19’ • Owner’s Manual Supplement
14
CHAPTER 3: COMPONENTS/SYSTEMS
Electrical System (12Volt DC)
Thoroughly read and understand this section, the electrical sections of the Sport
Boat Owner’s Manual and all accessory manuals included in your boat’s owner’s
packet. Wiring diagrams are provided in Chapter 4 of this supplement.
!
•
•
•
•
•
DANGER!
EXTREME FIRE, ELECTRIC SHOCK
and EXPLOSION HAZARD!
To minimize the risks of fire, electric shock and explosion:
NEVER install knife switches or other arcing devices in the fuel
compartments.
NEVER substitute automotive parts for marine parts. Electrical, ignition
and fuel system parts were designed and manufactured to comply with
rules and regulations that minimize risks of fire and explosion.
Ensure all of the battery switches are in the OFF position before performing any work in the engine spaces.
DO NOT modify the electrical systems or relevant drawings.
Only qualified personnel should install batteries and/or perform maintenance on the electrical system.
!
WARNING!
FIRE & EXPLOSION HAZARD!
• Fuel fumes are heavier than air and will collect in the bilge areas where
they can be accidently ignited. Visually and by smell (sniff test), check the
engine and fuel compartments for fumes or accumulation of fuel. Always
operate the bilge blowers for at least four minutes prior to engine starting,
electrical system maintenance or activation of electrical devices.
• Minimize the danger of fire and explosion by not exposing batteries to
open flame or sparks. It is also important that no one smoke anywhere
near the batteries.
! CAUTION!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
•NEVER disconnect the battery cables while the engine is running
since damage may occur to your boat’s electrical system components.
• The battery charging systems (alternators and battery charger) are
designed to charge conventional lead-acid batteries. Before installing gelcell (or other new technology) batteries, read and follow the battery
charger’s operating instructions.
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 3: COMPONENTS/SYSTEMS
15
NOTICE
Electrical connections are prone to corrosion. To reduce corrosion caused electrical problems, keep all electrical connections clean and apply a spray-on protectant that is designed to protect connections from corrosion.
NOTICE
VOLTAGES - All boats use either 110-volt AC/60 Hertz, 240-volt AC/60
Hertz or 220-volt AC/50 Hertz single phase systems, and 12-volt DC or 24volt DC. Electrical distribution panels are labeled with voltage and frequency
of AC and DC.
Fuses and/or Circuit Breakers
Please read the electrical section of the Sport Boat Owner’s Manual for important
safeguards concerning your boat’s fuse block.
FUSE BLOCK (TYPICAL)
12v POWER
SUPPLY, RED WIRE
DEPTH FINDER
(OPTION), RED WIRE
10 amp
10 amp
BLANK (SPARE 10 amp)
10 amp
15 amp
BLOWER (I.O. BOATS
ONLY), YELLOW WIRE
5 amp
10 amp
HORN, BROWN/
GREEN WIRE
INSTRUMENTS,
BLUE WIRE
10 amp
10 amp
NAVIGATION/ANCHOR
LIGHTS, BLUE WIRE
BILGE PUMP,
BROWN WIRE
5 amp
10 amp
STEREO, RED WIRE
IGNITION SWITCH
(I.O. BOATS ONLY),
RED/PURPLE WIRE
Capri 16’ - 19’ • Owner’s Manual Supplement
16
CHAPTER 3: COMPONENTS/SYSTEMS
Dash Programming (1952BV only)
M
S
Use the M “LCD Mode” switch to
toggle through the 7 basic settings.
Press both M “LCD Mode” and
S “LCD Set” at the same time to
enter or change values.
Arrow(s) show current function.
Clock
M and S
Depth, Ft/M
M and S
Distance Log
Trip Log
M and S
To Reset to 0.0
Total Hours
Trip Hours
Seawater Temp
(option)
Capri 16’ - 19’ • Owner’s Manual Supplement
M and S
To Reset to 0.0
CHAPTER 3: COMPONENTS/SYSTEMS
S to set Hours
M to go to Minutes
S to set Minutes
S decreases
Depth Alarm
Value-M to next
17
M to go to 24:12
S to Select
M to exit
S increases
Depth Alarm
Value-M to next
S to Select
Feet or Meters
M to next
S to
Select Depth
ON or OFF
Note
Setting Depth to METERS
will change Distance and
Trip logs to km (kilometers)
and Seawater Temp (option)
to C (centigrade)
Note
If you see ProG on the
display you have entered the
programing mode. Turn the
key off to exit. Do not
change programmed values.
Capri 16’ - 19’ • Owner’s Manual Supplement
18
CHAPTER 3: COMPONENTS/SYSTEMS
Controls
Read and understand the Controls section of both the Sport Boat Owner’s Manual
and engine manual, provided in the owner’s packet, for instructions and warranty
information.
Navigation and Interior Lights
Read the navigation light section of the Sport Boat Owner’s Manual. The navigation and interior lights supplied with your boat are of top quality, but you should
be aware that failure may periodically occur for a variety of reasons:
•
•
•
•
There may be a blown fuse - replace the fuse in the switch panel.
The bulb may be burned out - carry spare bulbs for replacement.
A wire may be damaged or may have come loose - repair as required.
The bulb base may be corroded - clean the base and coat it with non-conductive
electrical lubricant.
! CAUTION!
• Conserve battery power. Prolonged operation of cabin interior lights
(overnight) will result in a drained battery.
• Avoid the storage of gear where it would block navigation lights from
view.
Compass
Your boat may come equipped with a compass. Carefully read and follow the manufacturer’s calibration and operating instructions provided in the owner’s packet.
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 3: COMPONENTS/SYSTEMS
19
Depth Finder
Your boat may come equipped with a depth finder. It will provide you with measurements of water depth beneath the boat and in many cases it may help you locate
schools of fish. The depth finder comes with its own manual. We suggest that you
read it carefully before using the unit.
!
WARNING!
DO NOT use the depth finder as a navigational aid to prevent collision, grounding, boat damage or personal injury. When the boat is moving, submerged
objects will not be seen until they are already under the boat. Bottom depths
may change too quickly to allow time for the boat operator to react. If you suspect shallow water or submerged objects, operate the boat at very slow speeds.
Bow Mount For Trolling Motor-1804PC and 1954CW
Some models are equipped a with trolling motor connection and a reenforced deck
area designed to support a trolling motor mounting bracket. Contact your selling
dealer for a list of compatible equipment and installation instructions.
1804PC TROLLING MOTOR CONTROL PANEL
VOLT METER
12 VOLT
POWER POINT
REENFORCED
DECK AREA
ACCESSORY LIVE
WELL
MOTOR
MOTOR
POWER
TILT
CONNECTION
The trolling motor system can be used safely with both a 12V or a 24V motor.
However, the voltage gauge will only register with a 24V motor.
Capri 16’ - 19’ • Owner’s Manual Supplement
20
CHAPTER 3: COMPONENTS/SYSTEMS
Anchoring
Read and understand the Anchoring section of the Sport Boat Owner’s Manual.
WARNING!
!
FLOODING AND SWAMPING HAZARD - Never anchor by the stern alone-there is less freeboard and flooding or swamping is more likely to occur. When
using only one anchor, secure the anchor line to the bow cleat or bow eye.
Ski Tow Ring
Your boat may be equipped with a ski
tow ring. Attach tow rope as shown in
the photo (right.)
SKI TOW RING
SKI TOW ROPE
Ski Pylon (outboard models)
Your boat may feature a ski
pylon. Read the manufacturer’s
operating instructions included
in your owner’s packet before
using the ski pylon. Carefully
observe the following warnings:
! WARNING!
It is critical that all pins are fully inserted through the pressure plates, base
plates and tow bar tubes. Improper insertion may cause injury or death.
!
WARNING!
When the tow bar is in use, all passengers must sit forward of the ski pylon and
keep their hands well clear of the pylon and rope. Failure to do so may result in
injury or death.
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 3: COMPONENTS/SYSTEMS
21
Hull Exterior Drains & Hardware
BOW
HATCH
DRAIN
TYPICAL BILGE
PUMP DRAIN
LOCATIONS
COOLER DRAIN
(ON PORT SIDE)
TYPICAL
TRANSOM
SINK DRAIN
ON SOME MODELS
(OPTION)
LIVE WELL DRAIN
ON SOME MODELS
(PORT SIDE)
BOW
EYE
BOARDING
LADDER
STERN EYE
(TYPICAL)
GARBOARD
DRAIN
Capri 16’ - 19’ • Owner’s Manual Supplement
22
CHAPTER 3: COMPONENTS/SYSTEMS
Quick Oil Drain System
All stern drive models are equipped with a quick oil drain system.
To drain the engine oil:
1. Remove the boat from the water.
2. Unscrew the garboard drain plug.
3.
Pull the draw cord until the oil drain plug and the oil drain hose slide out of the
garboard drain.
4.
Place the end of the oil drain hose into a suitable container.
5.
Unscrew the oil drain plug and drain the engine oil.
6.
Replace the oil drain plug.
7.
Push the drain hose back into the bilge.
8.
Replace the garboard drain plug.
Always dispose of waste oil in accordance with local regulations.
QUICK OIL DRAIN SYSTEM
TRANSOM
OIL DRAIN HOSE
OIL DRAIN PLUG
GARBOARD
DRAIN PLUG
DRAW
CORD
BILGE
GARBOARD
DRAIN
Capri 16’ - 19’ • Owner’s Manual Supplement
ENGINE OIL PAN
CHAPTER 3: COMPONENTS/SYSTEMS
23
Fuel System
Fuel Fills and Vents
Fuel fills are located either on the aft deck or on the side decks adjacent to the aft
cockpit. Fuel receptacle caps are marked “GAS”. Fuel vents are normally located in
the hull or transom below and in the same general area as the fill. If you experience
difficulty filling the fuel tank, check to see that the fuel fill and vent lines are free of
obstructions and kinks.
Fuel Filters
Fuel filters should be replaced periodically to ensure that they remain clean and free
of debris. A fine mesh screen filter is located on the fuel pickup tube. An additional
filter, when supplied by the engine manufacturer, is installed on the engine.
Consult your selling dealer or local marina concerning fuel additives that help to
prevent fungus or buildup in your fuel tanks.
TYPICAL FUEL SYSTEM
FUEL TANK
DECK FITTING
FUEL FILL
FWD
FUEL TANK
VENT
FUEL FEED
HOSE
! WARNING!
FIRE/EXPLOSION HAZARD
It is very important that the fuel system be inspected thoroughly the first
time it is filled and then at each subsequent filling. For your safety and the
safety of your passengers, the fueling instructions in the Sport Boat Owner’s
Manual must be followed.
! CAUTION!
Avoid the storage or handling of gear near the fuel lines, fittings and tank.
Capri 16’ - 19’ • Owner’s Manual Supplement
24
CHAPTER 3: COMPONENTS/SYSTEMS
Bilge Blower
The bilge blower removes fumes from the engine compartment and draws fresh air
into the compartment through the deck vents.
To ensure fresh air circulation, operate the bilge blower for at least four minutes
before starting the engine, during starting, and while operating the boat below
cruising speed.
TYPICAL BLOWER SYSTEM
! WARNING!
FIRE/EXPLOSION HAZARD
Operation of the blower system is NOT A GUARANTEE that explosive fumes
have been removed. If you smell any fuel, DO NOT start the engine.
If the engine is already running, immediately shut off the engine and all electrical accessories. Investigate immediately. DO NOT obstruct or modify the ventilation system.
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 3: COMPONENTS/SYSTEMS
25
Live Well System
Your boat may feature a live
well. The live well aerator
pump(s) are located aft, adjacent to the bilge pump. The
live well intakes are throughtransom.
TO AFT
LIVE WELL
TRANSOM
LIVE WELL
AERATOR PUMP
(TYPICAL)
PLASTIC
SCREEN
FILTER
Switches for the live well are
located on the forward electrical panel and on the main
dash panel. These switches
activate the aerator that
pumps a continuous supply of
fresh water into the live well.
The overflow is automatically
drained overboard.
TO FWD
LIVE WELL
Occasionally check the live
well when it is operating to
see that the aerator is pumping adequate amounts of water. If there appears to be a problem, check the system,
including the plastic screens over the transom intakes for weeds or other debris.
The livewell is drained by removing the stand pipe (see photos below) and allowing
water to drain completely.
LIVE WELL
AERATOR
VALVE
DRAIN TO
THRU-HULL
STAND PIPE
REMOVED
STAND PIPE
ATTACHED
NOTICE
The live well pump should be shut off while underway at planing speeds.
Capri 16’ - 19’ • Owner’s Manual Supplement
26
CHAPTER 3: COMPONENTS/SYSTEMS
Bilge Pump
TYPICAL BILGE PUMP SYSTEM
This boat is equipped with one
bilge pump, located at the lowest point of the bilge.
Check the bilge pump often to
make sure it is working properly. To check the bilge pump:
TYPICAL PUMP
LOCATION IS
UNDER ENGINE
BILGE
PUMP
TRANSOM
The electric bilge pump supplied with your boat is an impeller-type pump. It is controlled
by a switch on the dash panel,
which should be turned on
whenever water begins to accumulate in the bilge.
• Turn on the dash-mounted
switch and make sure that
water in the bilge is pumped
overboard.
THRU
HULL
If bilge water is present and the
pump motor is running but not
pumping:
• Inspect the bilge pump hose
for a kink or collapsed area.
If the bilge pump hose is not the problem, check the bilge pump housing for clogging debris:
To remove the power cartridge:
1.
2.
TAB
FIN
Lift the tab while rotating the fins
counter clockwise and lift out the
power cartridge (Fig. 1).
Clear the housing of debris.
FIG. 1
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 3: COMPONENTS/SYSTEMS
To reinstall the power cartridge:
1.
2.
Make sure the “O” ring is properly
located and coat the “O” ring with
a light film of vegetable oil or mineral oil (Fig. 2).
Align the two cams on either side
of the power cartridge with the two
slots on the outer housing. Press the
power cartridge into the housing
and twist clockwise. Ensure proper
reinstallation by attempting to twist
the fins counter clockwise without
lifting the tab. The cartridge should
stay in place.
LIGHT FILM “O” RING
OF OIL
27
POWER
CARTRIDGE
FIG. 2
NOTICE
Discharge of oil, oil waste or fuel into navigable waters is prohibited by law.
Violators are subject to legal action by the local authorities.
Capri 16’ - 19’ • Owner’s Manual Supplement
28
CHAPTER 3: COMPONENTS/SYSTEMS
Jump Seat to Sunlounge Conversion
Models, 1950CL,1952CN, and 1954CW
!
DANGER!
DANGER
PERSONAL SAFETY HAZARD!
DO NOT allow anyone to ride on the aft sunlounge cushions while
underway or anytime the engine is running.
C A
A C
Step - 1: Remove the
jump seats (A) by sliding them forward.
MOTOR BOX
A
B
Step - 2: Slide the lounge support inserts
(B) into the lounge support slots (C).
C
Step - 3: Press down
firmly on the inboard
side of each jump seat
until they rest firmly on
the motorbox ledges.
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 3: COMPONENTS/SYSTEMS
29
Models, 1750BE, 1850BH, 1950BT and 1952BV
!
DANGER!
DANGER
PERSONAL SAFETY HAZARD!
DO NOT allow anyone to ride on the aft sunlounge cushions while
underway or anytime the engine is running.
Step - 1: Remove the jump seats
(A) by unsnapping the safety
straps (B) and lifting the seats
up and pulling them forward.
B
A
C
E
E
A
C
MOTOR BOX
D
E
B
B
Step - 2: Set the outboard edge of
the jump seats on the cockpit ledges
(C). Align the lounge support inserts
(D) into the lounge support slots (E).
D
E
C
A
Step - 3: Press down firmly on
each jump seat until they rest
firmly on the cockpit and motor
box ledges.
1950BT owner’s: Skip step 4 and
go to Step 4B on the next page.
Step - 4: Snap the safety straps
to the snaps on the motor box.
! WARNING!
PERSONAL SAFETY HAZARD! Attach safety strap underneath the seat
prior to using the seat in the sun lounge position.
Capri 16’ - 19’ • Owner’s Manual Supplement
30
CHAPTER 3: COMPONENTS/SYSTEMS
VIEW UNDER PORT JUMP SEAT IN SUNLOUNGE POSITION (MODEL 1954BT)
MOTOR BOX
SAFETY
STRAP
AFT COCKPIT WALL
SLIDE EYELET
OVER TURNBUCKLE
TURN TURNBUCKLE 90°
CORRECTLY
FASTENED
TURNBUCKLE
TURNBUCKLE
EYELET
Step - 4b for 1950BT: As shown above, attach the safety straps to the turnbuckles on the on the aft wall of the cockpit.
! WARNING!
PERSONAL SAFETY HAZARD! Attach safety strap underneath the seat
prior to using the seat in the sun lounge position.
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 3: COMPONENTS/SYSTEMS
31
Sleeper Seat Adjustment
Your boat may be equipped with adjustable sleeper seats. These seats can be
adjusted fore and aft in the upright position. The seat bottoms of these models also
adjust into backrests while the seat is in the lounge position.
Operating Positions:
To slide the seat forward:
OPERATING POSITIONS
1.
2.
Lift the forward seat at point (A).
Push down on the forward seat at point (B)
and pull the seat forward.
SEAT BOTTOM
3.
Lock the forward seat into the desired
position by pushing down at point (A).
C
4.
Lift the aft seat at point (C).
5.
Push down on the aft seat at point (D) and
push the seat forward until the aft seat
back is flush against the forward seat back.
6.
Lock the aft seat into position by pushing down at point (C).
SEAT BACK
D
B
A
SEAT BASE
FORWARD
To slide the seat aft, repeat the steps above, but start with the aft seat.
Lounge positions:
1.
2.
LOUNGE POSITIONS
Lift the forward seat at
point (A).
Push down on the forward
seat at point (B) and pull the
seat forward until the seat
back and bottom are flat.
3.
Lift the aft seat at point (C).
4.
Push down on the aft seat at
point (D) and pull the seat
aft until the seat back and
bottom are flat.
SEAT BOTTOM
D
2.
B
C
A
SEAT BASE
FORWARD
SEAT BACK
SEAT BOTTOM
C
A
To adjust into the chaise
lounge position:
1.
SEAT BACK
SEAT BASE
E
F
Lift up on the forward or aft
seat bottom at point (A or
C) and push the seat bottom down into the locked position.
To lower the seat bottom, lift the seat at point (A or C). Drop the seat bottom
flat while holding the seat down at point (E).
To return the seats to the operating position:
1.
2.
Lift the seat backs at point (F) and push down on the back edge of the seat bottom (B) and then seat bottom (D).
Push the seat bottoms towards the center of the seat until the seat backs are
flush against each other and locked into place.
Capri 16’ - 19’ • Owner’s Manual Supplement
32
CHAPTER 3: COMPONENTS/SYSTEMS
Removable Fishing Seats (1804PC and 1954CW)
Your boat may feature one or two removable fishing seats. All fishing seats
should be removed and stowed in a safe and secure area while underway or
when trailering your boat.
TYPICAL REMOVABLE FISHING SEAT
REMOVABLE
FISHING
SEATS
SUPPORT
POST
PARTS
!
WARNING!
Avoid serious or fatal falls and injuries by never occupying fishing seats when
boat speed exceeds 5 mph. Always remove seat when not being occupied.
!
DANGER!
PERSONAL SAFETY HAZARD! DO NOT allow anyone to ride on
parts of the boat not designated for such use.
Sitting on seat backs, lounging on the forward deck, bow riding, gunwale riding
or occupying the transom platform or the aft sunlounge cushions while underway is especially hazardous and WILL cause personal injury or death.
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 3: COMPONENTS/SYSTEMS
33
Canvas Top (Option) Installation
CANVAS INSTALLATION (TYPICAL VIEW)
G
L
F
H
E
I
K
J
M
B
D
A
C
1.
Insert eye ends (A) of main bow (B) into deck hinges (C) and secure with
pins (D).
2.
Unfold canvas top and snap front edge of top (E) to windshield frame.
3.
Close front zipper (F).
4.
Pull aft on aft edge of top (G), making sure canvas lies evenly from side to
side, and hook hold down straps (H) to deck loops (I).
5.
If canvas top does not have a smooth, taut look, tighten hold down straps by
pulling on strap buckle (J).
6.
Align secondary bow (K) with center seam of canvas by loosening or tightening top straps (L).
7.
No adjustments to jaw slides (M) should be needed as they are preset during
manufacturing. Before attempting to adjust jawslides, obtain correct measurements from your selling dealer.
8.
If additional canvas (i.e. side curtains, slant back cover, or camper cover) is
installed, canvas top may need readjustment to align snaps on canvas with
snaps on boat. Like top, additional canvas pieces should be smooth and taut.
Capri 16’ - 19’ • Owner’s Manual Supplement
34
CHAPTER 3: COMPONENTS/SYSTEMS
! CAUTION!
Take down and securely stow the convertible top, side curtains and back cover
before transporting your boat by road.
Canvas Stowage
Your boat may feature ventilated stowage space for the canvas top under either the
canvas stowage cover or the aft sunlounge pad.
CANVAS STOWAGE (TYPICAL VIEWS)
STANDARD SEATING
CANVAS
STOWAGE
COVER
MOTOR BOX
CANVAS TOP
SPORT SEATING
SUNLOUNGE/
MOTOR COVER
CANVAS TOP
Capri 16’ - 19’ • Owner’s Manual Supplement
35
CHAPTER 4: WIRING DIAGRAMS
1600CF and 1800CJ
Capri 16’ - 19’ • Owner’s Manual Supplement
36
CHAPTER 4: WIRING DIAGRAMS
1804PC
Capri 16’ - 19’ • Owner’s Manual Supplement
CHAPTER 4: WIRING DIAGRAMS
37
1750BE, 1850BH/CB, 1950BT/BU and 1952BV/BW
Capri 16’ - 19’ • Owner’s Manual Supplement
38
CHAPTER 4: WIRING DIAGRAMS
1950CL, 1952CN and 1954CW
Capri 16’ - 19’ • Owner’s Manual Supplement
39
APPENDIX A: BAYLINER CAPRI LIMITED WARRANTY
Bayliner provides the following BAYLINER CAPRI LIMITED WARRANTY to the original retail purchasers of its 2002/2003
Capri model boats, purchased from an authorized dealer, operated under normal, noncommercial use:
Limited Lifetime Structural Hull Warranty
The selling dealer will repair or replace, at Bayliner’s option, any Structural Hull Failure, as defined below, which is caused by a
defect in factory materials or workmanship, for as long as the original purchaser owns the boat. For purposes of this BAYLINER
CAPRI LIMITED WARRANTY: 1) The “Hull” shall mean the single fiberglass molded shell and integral structure within that
shell, including stringers, floorboards and related structural reinforcements, all of which are below the hull flange; and 2) a “Structural Hull Failure” shall mean a substantial failure or defect in the boat’s Hull which causes the boat to be unfit or unsafe for general
use as a pleasure craft under normal operating conditions. IN NO EVENT SHALL BAYLINER’S LIABILITY TO CUSTOMER
EXCEED THE FAIR MARKET VALUE OF CUSTOMER’S BOAT AS OF THE DATE OF CUSTOMER’S CLAIM.
One Year Parts and Components Limited Warranty
The selling dealer will repair or replace, at Bayliner’s option, any part or component found to be defective in factory materials or
workmanship which does not constitute a Structural Hull Failure or a Cosmetic Gelcoat Defect, as defined below, within one (1)
year of the date of delivery of your boat.
Six Month Cosmetic Gelcoat Defect Limited Warranty
The selling dealer will repair or replace, at Bayliner’s option, any Cosmetic Gelcoat Defect within six (6) months of the date of
delivery of your boat. For purposes of this BAYLINER CAPRI LIMITED WARRANTY, a Cosmetic Gelcoat Defect shall mean
any discoloration, crack, crazing or air void in the boat’s Gelcoat which is caused by a defect in factory materials or workmanship and which does not constitute a Structural Hull Failure.
THE REMEDIES PROVIDED IN THIS BAYLINER CAPRI LIMITED WARRANTY SHALL CONSTITUTE OWNER’S
SOLE AND EXCLUSIVE REMEDY.
What Is Not Covered
This BAYLINER CAPRI LIMITED WARRANTY does not apply to:
1. Engines, drive trains, controls, props, batteries, or other equipment or accessories that carry their own individual warranties,
all of which warranties are hereby assigned to owner to the extent permitted by the manufacturer of such components, equipment or accessories, as owner’s sole and exclusive remedy with respect to such items;
2. Engines, parts or accessories not installed by Bayliner;
3. Rainwater leakage, including rainwater leakage through convertible tops;
4. Cosmetic gelcoat discoloration, cracks, crazing or air voids occurring more than six months from the date of delivery;
5. Hull blisters that form below the waterline;
6. Normal deterioration, including but not limited to wear and tear or corrosion of hardware, vinyl, tops, upholstery, trim tape,
plastic, metal or wood;
7. Any Bayliner boat which has been overpowered according to Bayliner factory specifications for such boat;
8. Any Bayliner boat used for commercial purposes;
9. Any defect caused by product abuse or misuse, alteration of the product, or failure of the customer to provide reasonable care
and maintenance.
Other Limitations
1. EXCEPT AS PROVIDED HEREIN, THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, ON THIS
BOAT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, ARE EXPRESSLY EXCLUDED. BAYLINER FURTHER DISCLAIMS ANY LIABILITY FOR PRODUCT FAILURE OR OTHER ECONOMIC LOSS ARISING FROM CLAIMS OF NEGLIGENCE,
DEFECTIVE DESIGN, MANUFACTURING DEFECT, FAILURE TO WARN AND/OR INSTRUCT, LACK OF SEAWORTHINESS, AND ANY OTHER THEORY OF LIABILITY NOT EXPRESSLY COVERED UNDER THE TERMS OF
THIS LIMITED WARRANTY.
2. TO THE EXTENT ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS IMPLIED BY LAW AND CAN NOT BE DISCLAIMED UNDER APPLICABLE LAW DESPITE THE DISCLAIMER HEREIN, SUCH WARRANTIES SHALL BE LIMITED TO THE DURATION OF ONE YEAR.
3. NEITHER BAYLINER NOR THE SELLING DEALER SHALL HAVE ANY RESPONSIBILITY FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGE; LOSS OF USE OF THE BOAT; LOSS OF TIME, PROFITS OR INCOME; INCONVENIENCE; COMMERCIAL OR ECONOMIC LOSS; OR ANY OTHER CONSEQUENTIAL OR INCIDENTAL DAMAGES.
4. IN NO EVENT SHALL BAYLINER’S LIABILITY TO CUSTOMER EXCEED THE FAIR MARKET VALUE OF CUSTOMER’S BOAT AS OF THE DATE OF CUSTOMER’S CLAIM.
5. Some jurisdictions do not allow limitations on how long any implied warranty lasts, so the above limitation may not apply to
you. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
Your Obligations
In order to comply with Federal regulations, and as a condition precedent to limited warranty coverage hereunder, you must submit your limited warranty registration card within 30 days of delivery of your boat. Bayliner’s receipt of the limited warranty
registration card is a condition precedent to limited warranty coverage. All warranty work or repairs must be referred to your
selling dealer for authorization as a condition precedent to limited warranty coverage.
YOU MUST GIVE US WRITTEN NOTICE OF YOURWARRANTY CLAIM PRIOR TO THE EXPIRATION OF YOUR
BAYLINER CAPRI LIMITED WARRANTY AND ALLOW US AN OPPORTUNITY TO RESOLVE THE MATTER.
We require that you return your boat, at your expense, to your selling dealer or, if necessary, to the Bayliner factory. You will be
responsible for all transportation, haul-outs and other expenses incurred in returning the boat for warranty service.
Transferability
This BAYLINER CAPRI LIMITED WARRANTY extends only to the first retail purchaser. Remaining coverage under this
BAYLINER CAPRI LIMITED WARRANTY may be transferred by the first retail purchaser once to a second owner upon written request to Bayliner within thirty (30) days of the purchase of the boat, accompanied by payment of a transfer fee to Bayliner
Marine Corporation in the amount of $250. In the event of such transfer, the Limited Lifetime Structural Hull Warranty will
expire ten (10) years from the date of original purchase by the first retail purchaser as reflected in Bayliner’s records. Bayliner
reserves the right to reject a warranty transfer request for a Capri that has been damaged, neglected, or otherwise previously
excluded from warranty.
Bayliner Marine Corporation
•
PO Box 9029
•
Everett, WA 98206
•
Phone: 360-435-8957
•
FAX: 360-403-4235
Owner’s Notes
B a y lin e r M a r in e
• P. O. B o x 9 0 2 9 • E v e r ett, W A 9 8 2 06 •
P art N u m b er 14 9 31 8
3 6 0 - 43 5 - 5 5 71