FTXG25-35EVMAW(S) operation manual - 3P166462-1_1

00_CV_3P166462-1.fm Page 1 Monday, October 3, 2005 7:50 PM
DAIKIN ROOM AIR CONDITIONER
Operation Manual
MODELS
FTXG25EVMAW FTXG25EVMAS
FTXG35EVMAW FTXG35EVMAS
01_EN_3P166462-1.fm Page 1 Tuesday, September 20, 2005 5:08 PM
CONTENTS
READ BEFORE OPERATION
Safety precautions ......................................... 2
Names of parts............................................... 4
Preparation Before Operation ........................ 7
OPERATION
AUTO · DRY · COOL · HEAT · FAN
Operation ..................................................... 10
Adjusting the Air Flow Direction ................... 12
POWERFUL Operation ................................ 14
OUTDOOR UNIT SILENT Operation .......... 15
INTELLIGENT EYE Operation ..................... 16
TIMER Operation ......................................... 18
CARE
Care and Cleaning ....................................... 20
TROUBLE SHOOTING
Trouble Shooting.......................................... 23
1
01_EN_3P166462-1.fm Page 2 Tuesday, September 20, 2005 5:08 PM
READ BEFORE OPERATION
Safety precautions
•
•
•
•
Keep this manual where the operator can easily find them.
Read this manual attentively before starting up the unit.
For safety reason the operator must read the following cautions carefully.
This manual classifies precautions into WARNING and CAUTION. Be sure to follow all precautions below: they are all
important for ensuring safety.
WARNING
CAUTION
If you do not follow these instructions exactly, the unit may If you do not follow these instructions exactly, the unit may
cause property damage, personal injury or loss of life.
cause minor or moderate property damage or personal injury.
Never do.
Be sure to follow the instructions.
Be sure to earth the air conditioner.
Never cause the air conditioner (including the remote
controller) to get wet.
Never touch the air conditioner (including the remote
controller) with a wet hand.
WARNING
• In order to avoid fire, explosion or injury, do not operate the unit when harmful, among which flammable or
corrosive gases, are detected near the unit.
• It is not good for health to expose your body to the air flow for a long time.
• Do not put a finger, a rod or other objects into the air outlet or inlet. As the fan is rotating at a high speed, it will
cause injury.
• Do not attempt to repair, relocate, modify or reinstall the air conditioner by yourself. Incorrect work will cause electric
shocks, fire etc.
For repairs and reinstallation, consult your Daikin dealer for advice and information.
• Do not insert fingers, poles, or other objects into the moving parts of the front panel or the outlet vent panel.
• The refrigerant used in the air conditioner is safe. Although leaks should not occur, if for
some reason any refrigerant happens to leak into the room, make sure it does not come in
contact with any flame as of gas heaters, kerosene heaters or gas range.
• If the air conditioner is not cooling (heating) properly, the refrigerant may be leaking, so call your dealer.
When carrying out repairs accompanying adding refrigerant, check the content of the repairs with our service staff.
• Do not attempt to install the air conditioner by your self. Incorrect work will result in water leakage, electric shocks or
fire. For installation, consult the dealer or a qualified technician.
• In order to avoid electric shock, fire or injury, if you detect any abnormally such as smell of fire, stop the operation and
turn off the breaker. And call your dealer for instructions.
CAUTION
• The air conditioner must be earthed. Incomplete earthing may result in electric shocks. Do not connect the
earth line to a gas pipe, water pipe, lightning rod, or a telephone earth line.
• In order to avoid any quality deterioration, do not use the unit for cooling precision instruments, food, plants, animals or works of art.
• Never expose little children, plants or animals directly to the air flow.
• Do not place appliances which produce open fire in places exposed to the air flow from the unit or under the
indoor unit. It may cause incomplete combustion or deformation of the unit due to the heat.
2
01_EN_3P166462-1.fm Page 3 Tuesday, September 20, 2005 5:08 PM
• Do not block air inlets nor outlets. Impaired air flow may result in insufficient performance or trouble.
• Do not stand or sit on the outdoor unit. Do not place any object on the unit to avoid injury, do not remove the fan guard.
• Do not place anything under the indoor or outdoor unit that must be kept away from moisture. In certain conditions,
moisture in the air may condense and drip.
• After a long use, check the unit stand and fittings for damage.
• Do not touch the air inlet and aluminum fins of outdoor unit. It may cause injury.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.
• To avoid oxygen deficiency, ventilate the room sufficiently if equipment with burner is used
together with the air conditioner.
• Before cleaning, be sure to stop the operation, turn the breaker off or pull out the supply cord.
• Do not connect the air conditioner to a power supply different from the one as specified. It may cause trouble or fire.
• Depending on the environment, an earth leakage breaker must be installed. Lack of an earth leakage breaker may
result in electric shocks.
• Arrange the drain hose to ensure smooth drainage. Incomplete draining may cause wetting of the building, furniture
etc.
• Do not place objects in direct proximity of the outdoor unit and do not let leaves and other debris accumulate around
the unit.
Leaves are a hotbed for small animals which can enter the unit. Once in the unit, such animals can cause malfunctions, smoke or fire when making contact with electrical parts.
• Do not operate the air conditioner with wet hands.
• Do not wash the indoor unit with excessive water, only use a slightly wet cloth.
• Do not place things such as vessels containing water or anything else on top of the unit. Water may penetrate into the unit and degrade electrical insulations, resulting in an electric shock.
Installation site.
■ To install the air conditioner in the following types of environments, consult the dealer.
• Places with an oily ambient or where steam or soot occurs.
• Salty environment such as coastal areas.
• Places where sulfide gas occurs such as hot springs.
• Places where snow may block the outdoor unit.
The drain from the outdoor unit must be discharged to a place of good drainage.
Consider nuisance to your neighbours from noises.
■ For installation, choose a place as described below.
• A place solid enough to bear the weight of the unit which does not amplify the operation noise or vibration.
• A place from where the air discharged from the outdoor unit or the operation noise will not annoy
your neighbours.
Electrical work.
• For power supply, be sure to use a separate power circuit dedicated to the air conditioner.
System relocation.
• Relocating the air conditioner requires specialized knowledge and skills. Please consult the dealer if relocation is necessary for moving or remodeling.
3
01_EN_3P166462-1.fm Page 4 Tuesday, September 20, 2005 5:08 PM
Names of parts
■ Indoor Unit
1
2
3
4
5
6
7
8
9
(With the panel closed)
11
10
18
17
14
15
16
13
12
4
01_EN_3P166462-1.fm Page 5 Tuesday, September 20, 2005 5:08 PM
■ Outdoor Unit
19
21
22
20
23
■ Indoor Unit
• The operation mode refers to the following
table.
TemperaAir flow
Mode
ture setting
rate
AUTO
25°C
AUTO
FTXG
1. Air filter
2. Titanium Apatite Photocatalytic
Air-Purifying Filter:
• These filters are attached to the inside of
the air filters.
• This switch is useful when the remote controller
is missing.
3. Air inlet
4. Front panel
6. Panel tab
13. Room temperature sensor:
• It senses the air temperature around the unit.
14. Operation lamp (green)
15. TIMER lamp (yellow): (page 18.)
7. Flap (horizontal blade): (page 12.)
16. INTELLIGENT EYE lamp (green): (page 16.)
8. Air outlet
17. INTELLIGENT EYE sensor:
• It detects the movements of people and automatically switches between normal operation
and energy saving operation. (page 16.)
5. Supporting plate:
• The supporting plate is used to support the
front panel during maintenance.
9. Louvers (vertical blades):
• The louvers are inside of the air outlet.
(page 12.)
10. Outlet vent panel
11. Display
12. Indoor Unit ON/OFF switch: (page 10.)
• Push this switch once to start operation.
Push once again to stop it.
18. Signal receiver:
• It receives signals from the remote controller.
• When the unit receives a signal, you will hear a
short beep.
• Operation start .............beep-beep
• Settings changed..........beep
• Operation stop ..............beeeeep
■ Outdoor Unit
19. Air inlet: (Back and side)
22. Drain hose
20. Air outlet
23. Earth terminal:
• It is inside of this cover.
21. Refrigerant piping and inter-unit cable
Appearance of the outdoor unit may differ from some models.
5
01_EN_3P166462-1.fm Page 6 Tuesday, September 20, 2005 5:08 PM
■ Remote Controller
1
2
5
3
7
6
9
10
8
11
13
12
14
16
4
17
15
< ARC433A41 >
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown with all
its displays ON for the purpose of explanation.)
3. SENSOR button: INTELLIGENT EYE
operation (page 16.)
4. POWERFUL button:
POWERFUL operation (page 14.)
5. TEMPERATURE adjustment buttons:
• It changes the temperature setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN) (page 10.)
6
8. SILENT button: OUTDOOR UNIT SILENT
operation (page 15.)
9. FAN setting button:
• It selects the air flow rate setting.
10. SWING button: (page 12.)
• Flap (Horizontal blade)
11. SWING button: (page 12.)
• Louvers (Vertical blades)
12. COMFORT AIRFLOW mode button:
(page 13.)
13. ON TIMER button: (page 19.)
14. OFF TIMER button: (page 18.)
15. TIMER Setting button:
• It changes the time setting.
16. TIMER CANCEL button:
• It cancels the timer setting.
17. CLOCK button: (page 9.)
01_EN_3P166462-1.fm Page 7 Tuesday, September 20, 2005 5:08 PM
Preparation Before Operation
■ To set the batteries
Position
1. Slide the front cover to take it off.
–
+
and
correctly!
2
2. Set two dry batteries (AAA).
3. Set the front cover as before.
3
1
ATTENTION
■ About batteries
• When replacing the batteries, use batteries of the same type, and replace the two old batteries
together.
• When the system is not used for a long time, take the batteries out.
• We recommend replacing once a year, although if the remote controller display begins to fade or if
reception deteriorates, please replace with new alkali batteries. Do not use manganese batteries.
• The attached batteries are provided for the initial use of the system.
The usable period of the batteries may be short depending on the manufactured date of the air
conditioner.
■ Replacing the Batteries
• When replacing the battery, remove the old battery, wait one minute, and then insert the new battery.
7
01_EN_3P166462-1.fm Page 8 Tuesday, September 20, 2005 5:08 PM
Preparation Before Operation
■ To operate the remote controller
• To use the remote controller, aim the transmitter at the
indoor unit. If there is anything to block signals
between the unit and the remote controller, such as a
curtain, the unit will not operate.
• Do not drop the remote controller. Do not get it wet.
• The maximum distance for communication is about 7m.
Receiver
■ To fix the remote controller holder on the wall
1. Choose a place from where the signals
reach the unit.
Remote controller
2. Fix the holder to a wall, a pillar, or similar
location with the screws procured locally.
holder
Set.
3. Place the remote controller in the
remote controller holder.
■ Turn on the power breaker
●
To remove, pull it upwards.
• Turning on the power breaker will cause the panel and
flap to open once and then close again.
(This is a normal procedure.)
Panel
CAUTION
Flap
• During operation (i.e. when the panel is open or being opened or closed), do not touch the
panel with your hands.
ATTENTION
■ About remote controller
• Never expose the remote controller to direct sunlight.
• Dust on the signal transmitter or receiver will reduce the sensitivity. Wipe off dust with soft cloth.
• Signal communication may be disabled if an electronic-starter-type fluorescent lamp (such
as inverter-type lamps) is in the room. Consult the shop if that is the case.
• If the remote controller signals happen to operate another appliance, move that appliance
to somewhere else, or consult the shop.
8
01_EN_3P166462-1.fm Page 9 Tuesday, September 20, 2005 5:08 PM
■ To set the clock
1. Press “CLOCK button”.
is displayed.
blinks.
2. Press “TIMER setting button” to
set the clock to the present time.
Holding down “
” or “
” button rapidly increases or decreases the time display.
3. Press “CLOCK button”.
blinks.
2
1, 3
NOTE
■ Tips for saving energy
• Be careful not to cool (heat) the room too much.
Keeping the temperature setting at a moderate level helps save energy.
• Cover windows with a blind or a curtain.
Blocking sunlight and air from outdoors increases the cooling (heating) effect.
• Clogged air filters cause inefficient operation and waste energy. Clean them
once in about every two weeks.
Recommended temperature setting
For cooling:26°C – 28°°C
For heating:20°C – 24°C
■ Please note
• The air conditioner always consumes 15-35 watts of electricity even while it is not operating.
• If you are not going to use the air conditioner for a long period, for example in spring or autumn, turn the breaker OFF.
• Use the air conditioner in the following conditions.
Mode
COOL
HEAT
DRY
Operating conditions
Outdoor temperature: 10 to 46°C
Indoor temperature: 18 to 32°C
Indoor humidity: 80% max.
Outdoor temperature: –15 to 20°C
Indoor temperature: 10 to 30°C
Outdoor temperature: 10 to 46°C
Indoor temperature: 18 to 32°C
Indoor humidity: 80% max.
If operation is continued out of this range
• A safety device may work to stop the operation.
• Condensation may occur on the indoor unit and drip.
• A safety device may work to stop the operation.
• A safety device may work to stop the operation.
• Condensation may occur on the indoor unit and drip.
• Operation outside this humidity or temperature range may cause a safety device to disable the system.
9
01_EN_3P166462-1.fm Page 10 Tuesday, September 20, 2005 5:08 PM
OPERATION
AUTO · DRY · COOL · HEAT · FAN Operation
The air conditioner operates with the operation mode of
your choice.
From the next time on, the air conditioner will operate
with the same operation mode.
■ To start operation
1. Press “MODE selector button”
and select a operation mode.
• Each pressing of the button advances the
mode setting in sequence.
4
: AUTO
2, 3
: DRY
1
: COOL
5
: HEAT
: FAN
2. Press “ON/OFF button”.
• The operation lamp will light up and the panel will open.
■ To stop operation
3. Press “ON/OFF button” again.
• The operation lamp will go off and the panel will close.
■ To change the temperature setting
4. Press “TEMPERATURE adjustment button”.
DRY or FAN mode
AUTO or COOL or HEAT mode
Press “
“
The temperature setting is not variable.
10
” to raise the temperature and press
” to lower the temperature.
Set to the temperature you like.
01_EN_3P166462-1.fm Page 11 Tuesday, September 20, 2005 5:08 PM
■ To change the air flow rate setting
5. Press “FAN setting button”.
DRY mode
AUTO or COOL or HEAT or FAN mode
Five levels of air flow rate setting from “
The air flow rate setting is not variable.
plus “
”“
” to “
”
” are available.
• Indoor unit quiet operation
When the air flow is set to “ ”, the noise from the indoor unit will become quieter.
Use this when making the noise quieter.
The unit might lose capacity when the air flow rate is set to a weak level.
NOTE
■ Note on HEAT operation
• Since this air conditioner heats the room by taking heat from outdoor air to indoors, the heating
capacity becomes smaller in lower outdoor temperatures. If the heating effect is insufficient, it is recommended to use another heating appliance in combination with the air conditioner.
• The heat pump system heats the room by circulating hot air around all parts of the room. After the
start of heating operation, it takes some time before the room gets warmer.
• In heating operation, frost may occur on the outdoor unit and lower the heating capacity. In that case,
the system switches into defrosting operation to take away the frost.
• During defrosting operation, hot air does not flow out of indoor unit.
■ Note on COOL operation
• This air conditioner cools the room by blowing the hot air in the room outside, so if the
outside temperature is high, performance drops.
■ Note on DRY operation
• The computer chip works to rid the room of humidity while maintaining the temperature as
much as possible. It automatically controls temperature and air flow rate, so manual
adjustment of these functions is unavailable.
■ Note on AUTO operation
• In AUTO operation, the system selects an appropriate operation mode (COOL or HEAT) based on
the room temperature at the start of the operation.
• The system automatically reselects setting at a regular interval to bring the room temperature to usersetting level.
• If you do not like AUTO operation, you can manually select the operation mode and setting
you like.
■ Note on air flow rate setting
• At smaller air flow rates, the cooling (heating) effect is also smaller.
11
01_EN_3P166462-1.fm Page 12 Tuesday, September 20, 2005 5:08 PM
Adjusting the Air Flow Direction
You can adjust the air flow direction to increase your
comfort.
■ To adjust the horizontal
blade (flap)
1. Press “SWING button
• “
”.
” is displayed on the LCD.
2. When the flap has reached the
desired position,
press “SWING button
” once
more.
• The flap will stop moving.
1, 2
3, 4
5, 6
■ To adjust the vertical
blades (louvers)
3. Press “SWING button
• “
”.
” is displayed on the LCD.
4. When the louvers have reached the desired position, press the
“SWING button
” once more.
• The louvers will stop moving.
■ To 3-D Airflow
1. 3. Press the “SWING button
” and the “SWING button
”:
the “ ” and “
” display will light up and the flap and louvers will
move in turn.
■ To cancel 3-D Airflow
2. 4. Press either the “SWING button
12
” or the “SWING button
”.
01_EN_3P166462-1.fm Page 13 Tuesday, September 20, 2005 5:08 PM
■ To start COMFORT AIRFLOW operation
5. Press “COMFORT AIRFLOW button”.
The flap orientation will change, preventing air from blowing directly on the
occupants of the room.
• “
” is displayed on the LCD.
〈COOL/DRY〉 The flap will go up.
〈HEAT〉 The flap will go down.
■ To cancel COMFORT AIRFLOW operation
6. Press “COMFORT AIRFLOW button” again.
NOTE
• When “SWING button ” is selected, the flap swinging
range depends on the operation mode. (See the figure.)
In COOL or DRY mode
Three-Dimensional (3-D) Airflow
• Using three-dimensional airflow circulates cold air, which
tends to collected at the bottom of the room, and hot air,
which tends to collect near the ceiling, throughout the
room, preventing areas of cold and hot developing.
10°
COOL/DRY
40°
STOP
approx. 10°~40°
Comfort Airflow
• The air flow is set automatically.
• The air direction is as shown in the figure at right.
■ ATTENTION
• Always use a remote controller to adjust the flap angle.
If you attempt to move it forcibly with hand when it is
swinging, the mechanism may be broken.
• Always use a remote controller to adjust the louvers
angles.
In HEAT or FAN mode
5°
30°
75°
HEAT
STOP
approx. 30°~75°
FAN
80°
approx. 5°~80°
In COMFORT AIRFLOW mode
COOL
5°
STOP
HEAT
80°
13
01_EN_3P166462-1.fm Page 14 Tuesday, September 20, 2005 5:08 PM
POWERFUL Operation
POWERFUL operation quickly maximizes the
cooling (heating) effect in any operation mode.
You can get the maximum capacity.
■ To start POWERFUL
operation
1. Press “POWERFUL button”.
• POWERFUL operation ends in 20 minutes.
Then the system automatically operates
again with the settings which were used
before POWERFUL operation.
• When using POWERFUL operation,
there are some functions which are not
available.
• “
1, 2
” is displayed on the LCD.
■ To cancel POWERFUL
operation
2. Press “POWERFUL button”
again.
NOTE
■ Notes on POWERFUL operation
• POWERFUL Operation cannot be used together with SILENT, or COMFORT Operation.
Priority is given to the function of whichever button is pressed last. (This does not include
SILENT operation.)
• POWERFUL Operation can only be set when the unit is running. Pressing the operation
stop button causes the settings to be canceled, and the “ ” disappears from the LCD.
• In COOL and HEAT mode
To maximize the cooling (heating) effect, the capacity of outdoor unit must be increased
and the air flow rate be fixed to the maximum setting.
The temperature and air flow settings are not variable.
• In DRY mode
The temperature setting is lowered by 2.5°C and the air flow rate is slightly increased.
• In FAN mode
The air flow rate is fixed to the maximum setting.
14
01_EN_3P166462-1.fm Page 15 Tuesday, September 20, 2005 5:08 PM
OUTDOOR UNIT SILENT Operation
OUTDOOR UNIT SILENT operation lowers the noise
level of the outdoor unit by changing the frequency and
fan speed on the outdoor unit. This function is
convenient during night.
■ To start OUTDOOR UNIT
SILENT operation
1. Press “SILENT button”.
• “
” is displayed on the LCD.
■ To cancel OUTDOOR UNIT
SILENT operation
2. Press “SILENT button” again.
1, 2
NOTE
■ Note on OUTDOOR UNIT SILENT operation
• This function is available in COOL, HEAT, and AUTO modes.
(This is not available in FAN and DRY mode.)
• POWERFUL operation and OUTDOOR UNIT SILENT operation cannot be used at the
same time.
Priority is given to POWERFUL operation.
• If operation is stopped using the remote controller or the main unit ON/OFF switch when
using OUTDOOR UNIT SILENT operation, “
” will remain on the remote controller
display.
15
01_EN_3P166462-1.fm Page 16 Tuesday, September 20, 2005 5:08 PM
INTELLIGENT EYE Operation
“INTELLIGENT EYE” is the infrared sensor which
detects the human movement.
■ To start INTELLIGENT
EYE operation
1. Press “SENSOR button”.
• “
” is displayed on the LCD.
■ To cancel the
INTELLIGENT EYE
operation
2. Press “SENSOR button” again.
[EX.]
When somebody in the room
• Normal operation.
• The INTELLIGENT EYE lamp lights up.
When nobody in the room
• 20 min. after, start energy
saving
operation.
• The INTELLIGENT EYE lamp goes off.
Somebody back in the room
• Back to normal operation.
• The INTELLIGENT EYE lamp lights up.
16
1, 2
01_EN_3P166462-1.fm Page 17 Tuesday, September 20, 2005 5:08 PM
“INTELLIGENT EYE” is useful for Energy Saving
■ Energy saving operation
• Change the temperature –2°C in heating / +2°C in cooling / +2°C in dry mode from set temperature.
• Decrease the air flow rate slightly in fan operation. (In FAN mode only)
Notes on “INTELLIGENT EYE”
• Application range is as follows.
Vertical angle 90°
Horizontal angle 110°
(Side View)
(Top View)
90°
7m
55° 55°
7m
• Sensor may not detect moving objects further than 7m away. (Check the application range)
• Sensor detection sensitivity changes according to indoor unit location, the speed of
passersby, temperature range, etc.
• The sensor also mistakenly detects pets, sunlight, fluttering curtains and light reflected off of
mirrors as passersby.
• INTELLIGENT EYE operation will not go on during powerful operation.
• Night set mode (page 18.) will not go on during you use INTELLIGENT EYE operation.
CAUTION
• Do not place large objects near the sensor.
Also keep heating units or humidifiers outside the sensor’s detection area. This sensor can
detect objects it shouldn’t as well as not detect objects it should.
• Do not hit or violently push the INTELLIGENT EYE sensor. This can lead to damage and
malfunction.
17
01_EN_3P166462-1.fm Page 18 Tuesday, September 20, 2005 5:08 PM
TIMER Operation
Timer functions are useful for automatically switching
the air conditioner on or off at night or in the morning.
You can also use OFF TIMER and ON TIMER in
combination.
■ To use OFF TIMER
operation
• Check that the clock is correct.
If not, set the clock to the present time.
(page 9.)
1. Press “OFF TIMER button”.
is displayed.
blinks.
2. Press “TIMER Setting button” until
the time setting reaches the point
you like.
• Every pressing of either button increases or
decreases the time setting by 10 minutes.
Holding down either button changes the
setting rapidly.
4
2
1, 3
3. Press “OFF TIMER button” again.
• The TIMER lamp lights up.
■ To cancel the OFF TIMER operation
4. Press “CANCEL button”.
• The TIMER lamp goes off.
NOTE
• When TIMER is set, the present time is not displayed.
• Once you set ON, OFF TIMER, the time setting is kept in the memory. (The memory is canceled when
remote controller batteries are replaced.)
• When operating the unit via the ON/OFF Timer, the actual length of operation may vary from the time
entered by the user.
■ NIGHT SET MODE
When the OFF TIMER is set, the air conditioner automatically adjusts the temperature setting (0.5°C
up in COOL, 2.0°C down in HEAT) to prevent excessive cooling (heating) for your pleasant sleep.
18
01_EN_3P166462-1.fm Page 19 Tuesday, September 20, 2005 5:08 PM
■ To use ON TIMER operation
• Check that the clock is correct. If not, set the
clock to the present time.
(page 9.)
1. Press “ON TIMER button”.
is displayed.
blinks.
2. Press “TIMER Setting button” until
the time setting reaches the point
you like.
• Every pressing of either button increases or
decreases the time setting by 10 minutes.
Holding down either button changes the
setting rapidly.
3. Press “ON TIMER button” again.
• The TIMER lamp lights up.
1, 3
4
2
■ To cancel ON TIMER
operation
4. Press “CANCEL button”.
• The TIMER lamp goes off.
■ To combine ON TIMER and OFF TIMER
• A sample setting for combining the two timers is shown below.
(Example)
Present time: 11:00 p.m.
OFF TIMER at 0:00 a.m.
ON TIMER at 7:00 a.m.
Display
(The unit operating)
Combined
ATTENTION
■ In the following cases, set the timer again.
• After a breaker has turned OFF.
• After a power failure.
• After replacing batteries in the remote controller.
19
01_EN_3P166462-1.fm Page 20 Tuesday, September 20, 2005 5:08 PM
CARE
Care and Cleaning
CAUTION
• Before cleaning, be sure to stop the operation and turn the breaker OFF.
• Always shut down the unit (and close the panel) before doing any work.
Opening the panel during operation may cause the panel to fall off.
Units
■ Indoor unit, Outdoor unit and Remote controller
1. Wipe them with dry soft cloth.
■ Front panel
1. Open the front panel.
• Open the front panel by placing a finger on the
panel tab on either side of the front panel.
2. Remove the front panel.
• With the front panel open so that it is almost horizontal, slide it to the right.
The revolving axis on the left will come off.
The revolving axis on the right can be removed by
sliding the front panel to the left.
3. Clean the front panel.
• Wipe it with a soft cloth soaked in water.
• Only neutral detergent may be used.
• In case of washing the front panel with water, dry
it with cloth, dry it up in the shade after washing.
4. Attach the front panel.
• Place the revolving axes on either side of the front
panel into the holes and slowly close.
(Press either side of the front panel.)
CAUTION
•
•
•
•
Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an injury.
When removing or attaching the front panel, use a robust and stable stool and watch your steps carefully.
When removing or attaching the front panel, support the front panel securely with hand to prevent it from falling.
For cleaning, do not use hot water above 40°C, benzine, gasoline, thinner, nor other volatile oils, polishing compound, scrubbing brushes, nor other hand stuff.
• After cleaning, make sure that the front panel is securely fixed.
20
01_EN_3P166462-1.fm Page 21 Tuesday, September 20, 2005 5:08 PM
Filters
1. Open the front panel.
• Open the front panel by placing a finger on the
panel tab on either side of the front panel and then
secure it using the supporting plate on the right.
2. Pull out the air filters.
• Push a little upwards the tab at the center of
each air filter, then pull it down.
Supporting plate
3. Take off the Titanium Apatite
Photocatalytic Air-Purifying Filter.
Titanium Apatite
Photocatalytic
• Hold the recessed parts of the frame and
unhook the four claws.
Air-Purifying Filter
Air filter
Filter frame
4. Clean or replace each filter.
See figure.
Tab
5. Set the air filter and the Titanium Apatite
Photocatalytic Air-Purifying Filter as they
were and close the front panel.
Push
• Be sure to insert the two tabs below.
• Return the supporting plate to its previous position.
• Press either side of the front panel.
■ Air Filter
1. Wash the air filters with water or clean them with
vacuum cleaner.
• If the dust does not come off easily, wash them with neutral detergent
thinned with lukewarm water, then dry them up in the shade.
• It is recommended to clean the air filters every two weeks.
■ Titanium Apatite Photocatalytic
Air-Purifying Filter (gray)
Tab
The Titanium Apatite Photocatalytic Air-Purifying Filter can be renewed
by washing it with water once every 6 months. We recommend replacing it once every 3 years.
[ Maintenance ]
1.
2.
3.
4.
5.
Remove dust with a vacuum cleaner and wash lightly with water.
If it is very dirty, soak it for 10 to 15 minutes in water mixed with a neutral cleaning agent.
Do not remove filter from frame when washing with water.
After washing, shake off remaining water and dry in the shade.
Since the material is made out of paper, do not wring out the filter when removing water from it.
[ Replacement]
1. Remove the tabs on the filter frame and replace with a new filter.
• Dispose of the old filter as flammable waste.
21
01_EN_3P166462-1.fm Page 22 Tuesday, September 20, 2005 5:08 PM
NOTE
• Operation with dirty filters:
(1) cannot deodorize the air.
(2) cannot clean the air.
(3) results in poor heating or cooling.
(4) may cause odour.
• To order Titanium Apatite Photocatalytic Air-Purifying Filter contact to the service shop
there you bought the air conditioner.
• Dispose of old filters as burnable waste.
Item
Part No.
Titanium Apatite Photocatalytic Air-Purifying Filter.
(with frame) 1 set
KAF952B41
Titanium Apatite Photocatalytic Air-Purifying Filter.
(without frame) 1 set
KAF952B42
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit.
Stop operation and consult the service shop if this is the case.
■ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the
inside.
• Press “MODE” button and select “FAN” operation.
• Press “ON/OFF” button and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote controller.
22
01_EN_3P166462-1.fm Page 23 Tuesday, September 20, 2005 5:08 PM
TROUBLE SHOOTING
Trouble Shooting
These cases are not troubles.
The following cases are not air conditioner troubles but have some reasons. You may just continue using it.
Case
Explanation
Operation does not start soon.
• When ON/OFF button was
pressed soon after
operation was stopped.
• When the mode was
reselected.
• This is to protect the air conditioner.
You should wait for about 3 minutes.
Hot air does not flow out soon
after the start of heating
operation.
• The air conditioner is warming up. You should wait for 1 to 4
minutes.
(The system is designed to start discharging air only after it
has reached a certain temperature.)
The heating operation stops
suddenly and a flowing sound
is heard.
• The system is taking away the frost on the outdoor unit.
You should wait for about 3 to 8 minutes.
The outdoor unit emits water or
steam.
■ In HEAT mode
• The frost on the outdoor unit melts into water or steam
when the air conditioner is in defrost operation.
■ In COOL or DRY mode
• Moisture in the air condenses into water on the cool
surface of outdoor unit piping and drips.
Mists come out of the indoor
unit.
■ This happens when the air in the room is cooled into mist by
the cold air flow during cooling operation.
The indoor unit gives out odour. ■ This happens when smells of the room, furniture, or
cigarettes are absorbed into the unit and discharged with the
air flow.
(If this happens, we recommend you to have the indoor unit
washed by a technician. Consult the service shop where you
bought the air conditioner.)
The outdoor fan rotates while
the air conditioner is not in
operation.
■ After operation is stopped:
• The outdoor fan continues rotating for another 60
seconds for system protection.
■ While the air conditioner is not in operation:
• When the outdoor temperature is very high, the outdoor
fan starts rotating for system protection.
The operation stopped
suddenly.
(OPERATION lamp is on.)
■ For system protection, the air conditioner may stop
operating on a sudden large voltage fluctuation.
It automatically resumes operation in about 3 minutes.
23
01_EN_3P166462-1.fm Page 24 Tuesday, September 20, 2005 5:08 PM
Check again.
Please check again before calling a repair person.
Case
The air conditioner does not
operate.
(OPERATION lamp is off.)
Check
• Hasn’t a breaker turned OFF or a fuse blown?
• Isn’t it a power failure?
• Are batteries set in the remote controller?
• Is the timer setting correct?
Cooling (Heating) effect is poor. • Are the air filters clean?
• Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
• Is the temperature setting appropriate?
• Are the windows and doors closed?
• Are the air flow rate and the air direction set appropriately?
• Is the unit set to the INTELLIGENT EYE mode?
(page 16.)
Operation stops suddenly.
(OPERATION lamp flashes.)
• Are the air filters clean?
An abnormal functioning
happens during operation.
• The air conditioner may malfunction with lightning or radio
waves. Turn the breaker OFF, turn it ON again and try
operating the air conditioner with the remote controller.
The front panel and outlet vent
panel will not open.
(OPERATION lamp flashes.)
• Is there something caught in the panel?
24
• Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
Clean the air filters or take all obstacles away and turn the
breaker OFF. Then turn it ON again and try operating the air
conditioner with the remote controller. If the lamp still flashes,
call the service shop where you bought the air conditioner.
• Remove the object and attempt operation again using the
remote control.
If the panel still does not open, contact your dealer if the
operation lamp is still flashing.
01_EN_3P166462-1.fm Page 25 Tuesday, September 20, 2005 5:08 PM
Call the service shop immediately.
WARNING
■ When an abnormality (such as a burning smell) occurs, stop operation and turn the breaker OFF.
Continued operation in an abnormal condition may result in troubles, electric shocks or fire.
Consult the service shop where you bought the air conditioner.
■ Do not attempt to repair or modify the air conditioner by yourself.
Incorrect work may result in electric shocks or fire.
Consult the service shop where you bought the air conditioner.
If one of the following symptoms takes place, call the service shop immediately.
■The power cord is abnormally hot or damaged.
■An abnormal sound is heard during operation.
■The safety breaker, a fuse, or the earth leakage breaker
cuts off the operation frequently.
■A switch or a button often fails to work properly.
■There is a burning smell.
■Water leaks from the indoor unit.
■ After a power failure
The air conditioner automatically resumes
operation in about 3 minutes. You should just
wait for a while.
Turn the breaker
OFF and call the
service shop.
■ Lightning
If lightning may strike the neighbouring area,
stop operation and turn the breaker OFF for
system protection.
Disposal requirements
Dismantling of the unit, treatment of the refrigerant, oil and eventual other parts, should be done in
accordance with the relevant local and national regulations.
We recommend periodical maintenance.
In certain operating conditions, the inside of the air conditioner may get foul after several seasons of
use, resulting in poor performance. It is recommended to have periodical maintenance by a specialist
aside from regular cleaning by the user. For specialist maintenance, contact the service shop where
you bought the air conditioner.
The maintenance cost must be born by the user.
25
01_EN_3P166462-1.fm Page 26 Tuesday, September 20, 2005 5:08 PM
MEMO
26
01_EN_3P166462-1.fm Page 27 Tuesday, September 20, 2005 5:08 PM
MEMO
27
01_EN_3P166462-1.fm Page 28 Tuesday, September 20, 2005 5:08 PM
MEMO
28
00_CV_3P166462-1.fm Page 2 Monday, October 3, 2005 7:50 PM
3P166462-1
M05B042
(0509) HT