QM-RMCRX-BA - Hills Industries Ltd

QM-RMCRX-BA
Room Media Controller and QuickMedia® Receiver
Crestron's MediaManager is a comprehensive family of affordable
products fusing high-performance AV signal distribution, device
control, and facility-wide system management. MediaManager simplifies
the art of ProAV system design and installation with complete
hardware, software, and low-cost wiring solutions.
The QM-RMCRX-BA combines a 2-Series Ethernet control system with a
QuickMedia® receiver, digital audio processor, and stereo amplifier to
provide a
cost-effective solution for AV signal routing and control as part of a
complete MediaManager AV presentation system.
QuickMedia® Transport
Crestron's ingenious QuickMedia transport routes all audio, video, and
RGB computer signals over a single inexpensive CAT5e type cable*.
Computer resolutions up to 1920 X 1200 pixels at 60Hz are supported
over cable runs up to 450 feet. Stereo audio and microphone signals
are transmitted digitally with high-performance 24-bit resolution.
QuickMedia Receiver
Mounted at the projector or plasma display location, the QM-RMCRX-BA
receives the QuickMedia (QM) signal from any QM Transmitter or
Distribution Center, breaking out each media signal to its respective
format to feed the AV inputs on the display device.
High-Res Computer and Video
Separate composite, S-Video, and RGBHV outputs deliver high-quality
video and high-resolution computer graphics to the display device.
Signal routing occurs automatically under the command of the control
system based upon the input source selected at the QM transmitter.
Software-controllable compensation maximizes image quality over long
cable runs.
High-Performance Audio
In addition to video and RGB, the QuickMedia transport carries four
channels of 24-bit digital audio comprising a stereo program signal
and two discrete microphone signals. Within the QM-RMCRX-BA, each of
the two incoming microphone signals is processed by its own 4-band
speech-optimized graphic equalizer. Versatile 4X3 mixing allows the
mic signals and stereo program signal to be precisely adjusted and
routed to any of three audio output channels. The three channels are
ordinarily configured to support discrete stereo program and mono
speech outputs, although any mix of signals is possible.
The three balanced line-level outputs can be connected directly to
inputs on the display device or used to feed a separate amplifier or
external powered speakers. A built-in 20 watt stereo amplifier is also
provided to drive a pair of speakers directly.
Professional Digital Audio Processing
Each output channel includes software-adjustable volume, bass, treble,
and mute, plus ten-band graphic equalization and 2-band parametric
equalization. In addition, the speech output includes up to 40mS of
delay adjustment for proper ceiling speaker alignment. All audio
processing and mixing is performed in the digital domain, adjustable
at setup using Crestron's QM Tools software (part of Crestron
Toolbox).
With such extensive audio features, the QM-RMCRX-BA effectively
eliminates the need for expensive outboard processors to tailor the
system's audio performance to the acoustical environment. Many
www.crestron.com
800.237.2041
parameters are controllable in real-time from a keypad or touchpanel,
and numerous presets can be saved for instant recall to reconfigure
settings for changing room conditions or varying source material.
Display Control Interface
The QM-RMCRX-BA includes two bidirectional RS-232 ports and one
IR/Serial port to provide full control of the display device and other
equipment. Two relay ports are also included for control of a
projection screen or lift. In addition, the four digital input ports
can accept the direct connection of room occupancy sensors and power
sensors for enhanced automation and monitoring.
2-Series Ethernet Control System
At the heart of the QM-RMCRX-BA is the
powerful 2-Series control engine, which can be configured to serve as
the master control system for an entire MediaManager system or as a
slave device communicating with other Crestron components via Cresnet
or Ethernet. The built-in high-speed Ethernet port and Web server
provide full connectivity for remote programming and diagnostics, and
seamless integration into control
networks of any size. Native support for Crestron e-Control®2
and RoomView®
applications delivers the industry's best IP-based control and help
desk solution. Best of all, complete MediaManager systems are easy to
design, program and adjust from start to finish using Crestron
SystemBuilder™ software.
> 2-Series Ethernet Control System and QuickMedia Receiver
> Built-in Web server supports e-Control 2 and RoomView
> RS-232, IR, digital in and relay control ports
> Composite, S-Video and RGBHV outputs
> Onboard audio mixing, equalization, and delay processing
> 3 Balanced audio line outputs and built-in 20W stereo
amplifier
QM-RMCRX-BA
> 22 nS delay skew compensation and self-peaking audio
SDRAM: 32 MB
NVRAM: 256 KB
Flash: 4 MB
NET: (2) 4-pin 3.5mm detachable terminal blocks;
Cresnet ports (paralleled), Master/Slave selectable;
Connect to Cresnet control network via CresCAT-QM or Cresnet cable
24VDC: (1) 2.1mm barrel DC power jack;
24 Volt DC power input (power supply included);
Passes through to NET ports to power additional Cresnet devices
LAN: (1) 8-wire RJ45 with 2 LED indicators;
10/100BaseT Ethernet port;
Green LED indicates link status;
Yellow LED indicates Ethernet activity
SPEAKER L - R: (2) 2-pin 5mm detachable terminal blocks;
Left & Right Speaker-level audio outputs;
Output Power: 10 Watts per channel at 4 or 8 ohms
Operating System
Connectors - Rear Panel
> Easy configuration and setup using SystemBuilder software
SPECIFICATIONS
Processor
CPU: 32-bit Freescale ColdFire® Microprocessor
Memory
Real-time, preemptive, multitasking kernel, multi-threaded; FAT32 file
system with long names; supports SIMPL™ Windows® and SIMPL+®
Ethernet
10/100BaseT, static IP or DHCP/DNS, SSL, auto-negotiating, full duplex TCP/
IP, UDP/IP, CIP, SMTP, SNMP, built-in Web server and e-mail client; supports
Crestron e-Control®2 XPanel and RoomView® applications
Video
Signal Types: RGB and composite, S-Video, or component† video
Video/HDTV Formats: NTSC or PAL, HDTV up to 1080i/1080p†
RGB Formats: RGBHV, RGBS, or RGsB
Gain: 0dB (75 ohms terminated)
Maximum Resolution: 1920 x 1200 @ 60Hz (at unity gain) with maximum
cable length of 450 feet and maximum compensation
QM Cable Compensation: 10-bit digitally controlled PEAK (bandwidth) and
BOOST (frequency); 4-bit digitally controlled SKEW delay, 0 to 22 ns
(independent for R/Pr, G/Y, and B/Pb)
Audio
Features: 4x3 mic/program matrix mixer, 2-channels mic EQ, stereo volume/
tone control and EQ on PROGRAM output, mono volume/tone control and EQ/
delay on SPEECH output, integrated power amplifier, QM auto-compensation
with self-peaking
D-A Conversion: 24-bit, 48 kHz
Output Volume Range: -80dB to +20dB, 0.1dB steps
Mixer Volume Range: -80dB to 0dB, 0.1dB steps
Input Compensation: ±10dB, 0.1dB steps
Mic EQ Filter Gain: ±12dB, 0.1dB steps
Mic EQ Filter Center Frequencies: 160, 500, 1.2k, 3k Hz
Bass Gain Range: ±12dB @ 100Hz, 0.5dB steps
Treble Gain Range: ±12dB @ 10kHz, 0.5dB steps
Output Equalization: 10-band graphic + 2-band parametric
PEQ Filter Gain: ±12dB, 0.1 dB steps
PEQ Filter Bandwidth: 0.1 to 3.0 octaves, 0.1 octave steps
PEQ Filter Center Frequency: 25Hz to 20kHz, 0.5Hz steps
PEQ Filter Types: Low Pass, High Pass, Peaking Eq, Notch, Treble Shelf,
Bass Shelf
GEQ Filter Gain: ±12dB, 0.1dB steps
GEQ Filter Center Frequencies: 31, 63, 125, 250, 500, 1k, 2k, 4k, 8k, 16k Hz
Speech Output Delay: 0 to 40 mS, 1mS steps
Frequency Response: 20Hz to 20kHz ±0.5dB
S/N Ratio: 94dB (line), 90dB (speaker) 20Hz to 20kHz A-weighted
THD+N: 0.05% (line), 0.7% (speaker) 20Hz to 20kHz
Connectors - Front Panel
QM: (1) 8-wire RJ45 female, QuickMedia input port;
Connects to QM output port of any QuickMedia device via CresCAT-QM or
CRESCAT-IM cable*
S-VIDEO: (1) 4-pin mini DIN female, S-Video (Y/C) output;
Output Level: 1.0 Vp-p (luma), 0.7 Vp-p (chroma);
Output Impedance: 75 ohms
VIDEO: (1) BNC female, composite video output;
Output Level: 1.0 Vp-p
Output Impedance: 75 ohms
RGBHV: (1) DB15HD female, RGB(VGA)/component video† output;
Formats: RGBHV, RGBS, RGsB, YPbPr;
Output Level: 1 Vp-p nominal;
Sync Level: 5 Vp-p nominal;
Output Impedance: 75 ohms;
H/V Sync Impedance: 100 ohms
G: 6-32 screw, chassis ground lug
AUDIO: (1) 9-pin 3.5mm detachable terminal block;
Comprises (3) balanced line-level audio outputs;
Output Impedance: 200 ohms balanced, 100 ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
INPUT 1 - 4: (1) 5-pin 3.5mm detachable terminal block;
Comprises (4) digital/contact closure inputs;
Rated for 0-24 Volts DC, referenced to GND;
Input Impedance: 2.2k ohms pulled up to 5 Volts DC;
Logic Threshold: 2.5 Volts DC nominal with 1 Volt hysteresis band
IR: (1) 2-pin 3.5mm detachable terminal block;
IR/Serial port;
IR output up to 1.2 MHz;
1-way serial TTL/RS-232 (0-5 Volts) up to 9600 baud
COM A - B: (2) DB9 male, bidirectional RS-232 ports;
Up to 115.2k baud, hardware and software handshaking support;
Com port B also serves as the computer console port
RELAY OUTPUT 1 - 2: (2) 2-pin 3.5mm detachable terminal blocks
comprising (2) normally open, isolated relays;
Rated 2 Amp, 50 Volts AC/DC;
MOV arc suppression across contacts
LED Indicators
QM LINK: (red) Indicates presence of a digital audio signal to signify a valid
QM connection
NET: (yellow) Indicates communication with Cresnet system
PWR: (green) Indicates DC power supplied to unit
ACT: (red) Indicates activity on the LAN port
COM A - B: (red x2) Indicate activity on each respective COM port
IR: (red) Indicates activity on the IR port
INPUT: (red) Indicate activity on any digital input port
Buttons
HW-R: Hardware reset (reboots the control system)
SW-R: Software reset (restarts the SIMPL program)
Power Requirements
38 Watts (1.6 Amps) @ 24 Volts DC(PW-2420RU power supply included)
Available Cresnet Power: 12 Watts using PW-2420RU (included)
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1905
www.crestron.com
QM-RMCRX-BA
Cresnet Power Usage: 38 Watts (1.6 Amps @ 24 Volts DC) with no power
supply connected to the 24VDC connector
Environmental
Temperature: 41° to 104°F (5° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Chassis: Steel, black matte powder coat finish, fan-cooled, vented top and
sides
Mounting: Free-standing, surface-mount, or pole-mount (adhesive feet and
[4] “L” brackets included, MK-QM-RMCRX pole mount kit sold separately)
Dimensions
Height: 2.53 in (6.43 cm)
Width: 7.67 in (19.48 cm)
Depth: 6.04 in (15.34 cm)
Weight
1.7 lbs (0.77 kg)
* For QuickMedia wiring use CresCAT-QM, CresCAT-IM, or quality CAT5e/
CAT6 cable with a delay skew of ≤15nS per 100m; the maximum
aggregate cable length and delay skew between any QM transmitter
(origination point) and QM receiver (endpoint) is 450 ft (137 m) and 22 nS; a
maximum of two QM midpoint devices may be inserted in a given QM signal
path; exceptions apply, refer to each respective product manual for full
detail.
† Component video or HDTV may require a suitable VGA-to-component
adapter or breakout cable, not provided.
Available Models
QM-RMCRX-BA: Room Media Controller and QuickMedia Receiver
Included Accessories
PW-2420RU Power Pack, Desktop, 24VDC, 2A (50 Watts), Regulated, US/
International [Included Quantity: 1]
Available Accessories
CBL-VGA-1.5: Crestron® Certified Computer VGA Interface Cable, 1.5 ft
CBL-VGA-12: Crestron® Certified Computer VGA Interface Cable, 12 ft
CBL-VGA-25: Crestron® Certified Computer VGA Interface Cable, 25 ft
CBL-VGA-3: Crestron® Certified Computer VGA Interface Cable, 3 ft
CBL-VGA-6: Crestron® Certified Computer VGA Interface Cable, 6 ft
CNSP-XX: Custom Serial Interface Cable
CNXRMCS: TV Current Sensor
CRESCAT-QM-NP-SP500: QuickMedia® Cable, Low-skew CAT5e & Cresnet,
non-plenum, 500 ft spool
CRESCAT-QM-P-SP500: QuickMedia® Cable, Low-skew CAT5e & Cresnet,
plenum, 500 ft spool
IRP2: IR Emitter Probe
MK-QM-RMCRX: Pole Mount Bracket for QM-RX and QM-RMCRX-BA
SW-ROOMVW-ENT: RoomView® Express - Remote Help Desk and Resource
Management Software
SW-ROOMVW-SERVER: RoomView® Server Edition - Enterprise Management
and Scheduling Software [Discontinued]
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1905
www.crestron.com
Typical QM-RMCX-BA Application
QM-RMCRX-BA
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1905
www.crestron.com
All brand names, product names and trademarks are the property of their respective owners.
©2013 Crestron Electronics, Inc.
Specifications subject to change without notice. 7/18/2013