CAN52.4ME
CAN75.3SS
Canopy hood
User Manual for your Baumatic
CAN52.4ME 52 cm
CAN75.3SS 75 cm
Canopy Hood
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
GS 02/01/13
2
Contents Page
Environmental note
4
IMPORTANT SAFETY INFORMATION
5–7
Specifications of your cooker hood
CAN52.4ME
CAN75.3SS
8 – 10
8
9 - 10
Using your Baumatic cooker hood
Before first use
To use your cooker hood
10 - 11
10
10 - 11
Cleaning your Baumatic cooker hood
General cleaning
The grease filter
11 – 12
11
12
Maintenance
Removing and cleaning the grease filter
Changing a light bulb
Fitting the carbon filters
12
12
13
14
– 16
- 13
- 14
- 16
Installation
Electrical connection
Before beginning installation
Installing your cooker hood
Connecting to external ducting
Completing the installation
16
17
17
18
20
21
- 21
Extraction mode or recirculation mode?
21 - 22
Troubleshooting
22 – 24
Baumatic consumables
25
Contact details
26
- 18
- 20
- 21
3
ENVIRONMENTAL NOTE
Note:
Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
4
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Customer
Care Department.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
o The hood must be installed in accordance with the installation
instructions and all measurements followed.
o If the cooker hood is installed for use above a gas appliance then
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scottish
Development Department.
o It is dangerous to alter the specifications or to modify this
product.
Do not tamper with it or attempt to modify the
appliance in any way.
o When installing the hood, ensure that the following
recommended distances are observed between the highest point
on the hob top (including the burners) and the bottom of the
cooker hood:
 Electric cookers:
 Gas cookers:
 Coal/ oil cookers:
700 mm
700 mm
800 mm
IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS
THAN 700mm ABOVE YOUR COOKER.
o When installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
5
o The edges of the cooker hood are sharp – be mindful of this as
you handle your appliance, especially during installation and
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS!
o If the room where the cooker hood is to be used contains a fuel
burning appliance such as a central heating boiler then its flue
must be of the sealed or balanced flue type.
o If other types of flue or appliances are fitted, ensure that there is
an adequate supply of air in the room.
o When the hood is being used in its extractor function, ensure
that the ducting is fire retardant and that there are no bends
sharper than 90 degrees as this will reduce the efficiency of the
hood.
o Ensure the ducting for the extractor function has the same
diameter as the outlet hole all the way through.
o Keep young children from using, playing with
or tampering with the cooker hood. Older
children and infirm persons should be
supervised if they are using the cooker hood.
o Your cooker hood is for domestic use only.
o Please dispose of the packing material carefully – children are
especially vulnerable to it.
o Dirty oil is an even greater fire risk.
o Always put lids on pots and pans when cooking
on a gas cooker.
o The manufacturer refuses to accept any responsibility for
damages arising to the hood or it catching on fire, from a failure
to observe the fire safety advice contained in this instruction
booklet.
6
o Remember that when in extraction mode, your cooker hood is
removing air from your room. Ensure that proper ventilation
measures are being observed.
o Note that it removes odours from your room, not steam.
o Warning - Always ensure that the cooker
hood has been disconnected from the
power supply before carrying out any work
on the hood, including replacing light bulbs.
o Do not connect the ducting system of this appliance to any
existing ventilation system which is being used for any other
purpose.
o Do not install above a cooker with a high level grill.
o Never leave frying pans unattended during use
as overheated fats and oils might catch fire.
o The cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. naked flame from a
gas burner or heat from electric hob zones without a pan on
them.
o Do not attempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filters fitted or
if the filters are excessively greasy!
o Never flambé cook under this cooker hood.
o The lights on this appliance should only be used during operation
of the cooker hood. They should not be left on permanently and
used as a lighting source.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY IN THE EVENT OF FAILURE TO
OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR
INSTALLATION, MAINTENANCE AND SUITABLE
USE OF THE HOOD.
7
Specifications of your cooker hood
CAN52.4ME
Product dimensions
Height:
Width:
Depth:
162 mm
520 mm
296 mm
Your canopy hood is fitted with:
o
o
o
o
o
o
o
Slider control operation
Integrated axial motor
3 speeds
1 washable aluminium grease filter
Non-return airflow flap
2 halogen lights
Noise level: 45 / 50 / 55 dB
Extraction capacity:
250 m³ / hr
Optional extras:
1 pair ST1 carbon filters for air recirculation
mode
DK5 1 metre length ducting kit 125 mm Ø
DK10 3 metre length ducting kit 125 mm Ø
with flat channelling included.
8
CAN75.3SS
Product dimensions
Height:
Width:
Depth:
245 mm
740 mm
295 mm
Your stainless steel canopy hood is fitted with:
o
o
o
o
o
o
o
Slider control operation
Integrated axial motor
3 speeds
1 washable aluminium grease filter
Non-return airflow flap
2 halogen lights
Noise level: 61 / 65 / 68 dB
Extraction capacity:
750 m³/hr
Optional extras:
1 pair S1 Carbon filters for air recirculation
mode
DK5 1 metre length ducting kit 125 mm Ø
DK10 3 metre length ducting kit 125 mm Ø
with flat channelling included.
All of the optional extras are available from the Baumatic
Spares Department.
9
Using your Baumatic cooker hood
Before first use
IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE
THE COOKER HOOD IS USED FOR THE FIRST TIME.
o You should use a good quality stainless steel cleaner on ALL of the
stainless steel areas of your cooker hood, before it is used for the
first time.
o This will help to leave a silicone water-resistant film to protect the
stainless steel surfaces.
To use your cooker hood
o Make sure that it has been installed by a suitably qualified person,
as per the information contained in Baumatic’s installation
instructions.
o Find the control panel, which is located at the front right of the
canopy.
o There are two sliders on the control panel, which perform separate
functions.
1) Light control. The light can be used even when the motor is OFF.
0 = Light OFF
1 = Light ON
2) Motor speed control.
= Low speed
= Medium speed
= High speed
10
IMPORTANT: IDEALLY YOU SHOULD SWITCH ON
YOUR HOOD TEN MINUTES BEFORE YOU START TO
COOK, OR AT THE VERY LEAST WHEN YOU BEGIN
COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR
TEN MINUTES AFTER YOU HAVE FINISHED COOKING.
Cleaning your cooker hood
IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE
THAT YOU HAVE SWITCHED YOUR COOKER HOOD
OFF AT THE OMNI-POLAR SWITCH, SET AT THE
WALL FROM THE CABLE.
Cleaning
o Clean the external parts of your cooker hood with mild liquid
detergent and a new damp cloth.
o Never use abrasive powder, corrosive solvents or brushes.
o Never insert pointed objects into the motor’s protective grid.
o Only clean the control panel and grease filter grill with mild liquid
detergents and a new damp cloth.
o If you are using the appliance in recirculation mode, then be
sure to replace the carbon filters at the recommended interval
(see section on “Fitting the carbon filter”). A build up of grease
could cause a fire hazard.
o Never attempt to clean the area above the grease filter.
o IMPORTANT: You should regularly use a good quality
stainless steel cleaner to maintain the shine and finish on
the stainless steel areas of your cooker hood.
o This will help to leave a silicone water-resistant film to protect
the stainless steel surfaces and keep them in good condition for
the life of the product.
11
The grease filter
o Your cooker hood includes a grease filter which helps to absorb
grease particles to protect your kitchen and furniture from
greasy residues.
o The metallic filter may become flammable if it becomes
saturated with greasy residue.
o To prevent this fire hazard, the filter should be cleaned regularly.
Depending on use, this should be done every 10-15 days or at
least once a month, using hot water and normal washing-up
detergent.
o DO NOT WASH THE GREASE FILTER IN A DISHWASHER.
Maintenance
Removing and cleaning the grease filter
o First remove the grease
filters by pulling down on the
handle and pulling them away
from the cooker hood.
o Soak the grease filter in hot water and washing up liquid for
about an hour.
o Rinse it off thoroughly with hot water.
o Repeat the process if required.
12
o Refit the grease filter once it
has dried.
o IMPORTANT: Let the
grease filter dry
thoroughly before
refitting it in the cooker
hood.
Changing a light bulb
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
A LIGHT BULB, YOU MUST ENSURE THAT YOU
HAVE DISCONNECTED THE COOKER HOOD FROM
YOUR MAINS SUPPLY.
o Remove the grease filter (as
described on page 12).
o Prior to touching the light bulbs
ensure that they have cooled
down.
o Find the bulb that requires
replacement, you will find it
located in the light fixture which
is inside the exposed section of
the canopy.
o Press gently on the underside of the bulb that needs to be
replaced and twist anticlockwise to release.
13
o Insert a new identical 40W (max) bulb.
o IMPORTANT: Defective bulbs should be replaced immediately.
o If the lights still do not work, make sure that the bulbs are fitted
properly into their housings before you call for technical
assistance.
o Refit the grease filter.
Fitting the carbon filter
If the appliance is going to be used in recirculation mode then it is
necessary to a fit a carbon filter. This will help to absorb unpleasant
odours caused by cooking.
IMPORTANT: BEFORE ATTEMPTING TO FIT OR
REMOVE THE CARBON FILTERS, YOU MUST
ENSURE THAT YOU HAVE DISCONNECTED THE
COOKER HOOD FROM YOUR MAINS SUPPLY.
o You will find that one filter will attach over the front of the fan
motor. The active carbon filter must be replaced at least every
four months depending on usage to allow normal operation when
in recirculation mode.
CAN52.4ME (1 x pair ST1 carbon filters)
o Remove the grease filters.
14
2) Hook the carbon filter over the
pins that are located at the end of
the motor.
3) Turn the carbon filter clockwise until you feel it latch
onto the motor’s sides.
4) Replace the grease filters.
o When replacing the carbon filter, follow the steps outlined above
and turn the carbon filter anti-clockwise to unlatch it from the
motor.
CAN75.3SS (1 x pair S1 carbon filters)
1) Remove the grease filters (as described
previously).
2) Hook the carbon filter over
the pins that are located at the
end of the motor.
15
3) Turn the carbon filter anticlockwise,
until you feel it click into place.
o Repeat this process for the second carbon filter. You need to
place a carbon filter at either end of the motor.
o Refit the grease filters.
o The carbon filters should be replaced every 3 - 6 months or if
they show signs of damage.
Installation
IMPORTANT: Before installation read all the
instructions and make sure that the voltage (V)
and the frequency (Hz) indicated on the rating
plate are exactly the same as the voltage and
frequency in your home. The rating plate can be
found behind the grease filters.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.
16
Electrical connection
YOUR COOKER HOOD IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
o The cooker hood’s power cable must be fitted upstream from the
electrical connection, using an omni-polar switch with a contact
distance of at least 3 mm. THE FUSE MUST BE RATED AT 3
AMPS.
WARNING: THIS APPLIANCE MUST BE EARTHED. It
should only be connected by a competent person, using
fixed wiring via a double pole switched fused spur outlet.
(UK ONLY).
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.E. and local regulations. The wires in the mains lead are
coloured in accordance with the following UK code:
Blue = Neutral, Brown = Live, Green/Yellow = Ground
If you only find two wires in the main’s lead (blue and brown),
then neither must be connected to the earth terminal.
o As the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals
in your spur box, please proceed as follows:
o The blue wire must be connected to the
terminal marked “N” (neutral), or coloured
black.
o The brown wire must be connected to the
terminal marked “L” (live), or coloured red.
Before beginning installation
o Check that the product purchased is of a suitable size for the
chosen installation area. In addition check whether there is an
electrical socket available that will be accessible once the hood is
mounted. If the product is going to be used in extraction mode,
then there should also be space to connect a ducting hose to the
outside.
o Carry out all necessary masonry work prior to the fitting of the
cooker hood.
17
o Ensure that all electrical connections are carried out by a suitably
qualified person.
o Before commencing installation of the cooker hood the grease
filter should be removed.
o Check inside the product and ensure that there is no transit
packaging or any other materials, such as packets of screws,
guarantees etc. These should be removed and kept for future
use.
o If possible, disconnect and move freestanding or slot-in cookers
from their position, to provide easier access to the rear wall and
ceiling. If this is not possible, then a thick, protective covering
should be placed over the worktop, hob top or cooker. This will
help to protect these surfaces from damage and debris.
o Select a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cooker hood
parts and fittings on it.
o Do not tile, grout or silicone this appliance to the wall or
cabinetry. This appliance is designed to be surface mounted
only.
Installing your cooker hood
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE. PLEASE TURN TO PAGE 21-22 NOW TO
UNDERSTAND THE DIFFERENCES BETWEEN THESE
TWO MODES.
o We recommend that two people install this hood.
o Your cooker hood should only be fitted into the underside of a
kitchen unit.
o It must be positioned at least 700 mm above the hob
underneath it. You cannot fit this product by securing it between
two cupboards.
IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED
TO YOUR MAINS SUPPLY AFTER THE REST OF THE
INSTALLATION PROCESS HAS BEEN COMPLETED.
1) Remove the metal grease filter (A).
18
2) Create an opening in the underneath of the kitchen unit; the cutout must be of the dimensions shown in the drawing below.
CAN52.4ME
CAN75.3SS
o IMPORTANT: If you are going to connect your cooker hood to
external ducting, then you must complete the steps listed in the
“Connecting to external ducting” section before carrying on with
the rest of the installation (this information can be found on
page 20).
3) Make a hole in the inside of the kitchen unit for the electrical cable
to feed through. Remove the 2 screws (4 screws for CAN52.4ME)
securing the extractor frame (B) to the hood and unscrew the 2 lights.
Ensure that the two support clips on either side of the hood are set to
accommodate the thickness of the mounting surface, by adjusting the
clip via the screw.
4) Lift the cooker hood towards the cut-out that you made in step 2.
Feed the electrical cable through the hole that you made in step 3.
19
IMPORTANT: Do not connect the electrical cable to the mains supply
at this stage.
5) Lift the cooker hood fully into the cut out that you made in step 2.
If you are connecting the cooker hood to external ducting, then secure
the ducting hose to the coupling on the appliance.
o One person should support the hood. The other person should
fully tighten the support screws through the pre-drilled holes in
the outer frame of the hood, into the kitchen unit. Then replace
the extractor frame using the 2 screws (4 screws for
CAN52.4ME) (B) and reattach the 2 lights.
o Refit the grease filter.
Connecting to external ducting
o Connect the coupling to the top of the cooker hood, using two of
the smaller screws provided.
o Connect a Ø125 mm ducting hose to a discharge outlet that is
suitable for cooking vapours.
o The discharge outlet should have a cross section of at least 150
cm² (please note that the ducting hose is not supplied with the
appliance but one can be obtained from the Baumatic Spares
Department).
o The maximum distance between the coupling and your discharge
outlet should be 3 metres, with one 90 degree bend. For each
additional 90 degree bend, the maximum distance is reduced by
a further metre.
o Before fixing the cooker hood into the kitchen unit, you should
connect the other end of the ducting hose to the coupling in the
top of the cooker hood.
20
Completing the installation
o If you are setting the appliance to recirculation mode, then you
should now fit the two carbon filters. See the “Fitting the carbon
filters” section on pages 14-16.
o The electrical connection must correspond to the electrical
requirement noted on the rating plate, which is placed inside the
cooker hood. The appliance should now be connected to the
electrical supply. See page 17 for detailed information on the
electrical connection.
o Refit the grease filter and then switch on the mains
supply to the appliance. Check that the appliance is
operating correctly by selecting each speed and
switching the light bulbs on and off.
Extraction mode or recirculation mode?
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE.
What is the difference between extraction and recirculation
modes?
In extraction mode, the stale air will be taken via the grease filter and
out of the room via external ducting.
In recirculation mode stale air is taken via the grease filter, and passed
through a charcoal filter for purification. The air then re-enters the
kitchen via an opening in the hood.
For optimum performance, we recommend that the cooker hood is
used in extraction mode and connected to external ducting.
Unfortunately if you live in a flat or the hood is too far from an outside
wall, this may not be possible. The only alternative is to recirculate the
air.
21
Recirculation:
Extraction:
Do I need a charcoal filter?
All cooker hoods have a grease filter but if you are using your cooker
hood in recirculation mode, then charcoal filters must be fitted in
addition to the grease filter.
Troubleshooting
IMPORTANT: If your cooker hood appears not to be operating
properly, before contacting the Customer Care Department,
please refer to the table below.
My cooker hood will not start.
o Check that the hood is connected to the power supply and
whether you have selected any of the fan speeds.
My cooker hood is not working effectively.
o Check that fan speed is set to an appropriate setting.
o Check that the grease filter is not dirty and if it requires
cleaning.
22
o If the hood is set up for recirculation mode, check that the
carbon filters do not need to be replaced.
o If the hood is set up for extraction mode, check that the ducting
hose and discharge outlet are not blocked.
My cooker hood is noisy and/or vibrating.
o Check whether the installation has been completed as per the
instruction booklet.
o It is normal to get a certain amount of noise and vibration, due
to the extraction capacity of the cooker hood.
DO NOT MAKE ANY ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF. IF THE APPLIANCE IS STILL NOT OPERATING
CORRECTLY,
PLEASE
CONTACT
THE
CUSTOMER
CARE
DEPARTMENT ON TELEPHONE NUMBER (0118) 933 6911.
23
My appliance isn’t working correctly
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact
Baumatic Customer Care on telephone number
(0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then they will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
IMPORTANT: Baumatic Ltd. operates a policy of continuous
improvement and reserves the right to adjust and modify its
products without prior notification.
24
Baumatic consumables
o BC001 Degreaser for Dishwashers (200g)
o BC002 Descaler for Washing Machines and Dishwashers (200g)
o BC003 Ceramic Hob Cleaner (250ml)
o BC004 Oven Cleaner (250ml)
o BC005 Stainless Steel Cleaner and Protector (250ml)
o BC007 E-Cloth – General Purpose Cloth
o BC008 Microwave Cover
To order a Baumatic consumable product please call 0123 5437 244
and quote the product code. You can also order online from
eshop.baumatic.co.uk
25
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
s,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Czech Republic
Baumatic CR s.r.o.
Lípovà 665
460 01 Liberec 4
Czech Republic
+420 483 577 200
www.baumatic.cz
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
Slovakia
Baumatic Slovakia, s.r.o.
Panenská 34
811 03 Bratislava - Staré Mesto
Slovakia
+421 255 640 618
www.baumatic.sk
Germany
Baumatic Gmbh
Bachstr.10-12
D-32 257 Bünde
Deutschland
E-mail:
sales@baumatic.co.uk
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
+49 (0) 5223 99408 0
www.baumatic.de
Website:
www.baumatic.co.uk
Italy
Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)
Facebook:
www.facebook.com/baumatic.uk
Republic of Ireland
+3904 9920 2297
www.baumatic.it
Service Telephone
1-890 812 724
Holland
Baumatic Benelux B.V.
Dukdalfweg 15d
1332 BH ALMERE
Nederland
Spares Telephone
091 756 771
+31(0)36 549 1555
www.baumatic.nl
26
27
28