Installation Guide: MMK-V15 & WMKM-V15

Crestron MMK-V15 & WMKM-V15
Mud Mount Kits
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
Industry Compliance
As of the date of manufacture, the MMK-V15 & WMKM-V15 have been tested and found to comply with
specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling.
All brand names, product names and trademarks are the property of their respective owners.
©2009 Crestron Electronics, Inc.
Crestron MMK-V15 & WMKM-V15
Mud Mount Kits
Contents
Mud Mount Kits: MMK-V15 & WMKM-V15
1
Description................................................................................................................................. 1
Setup .......................................................................................................................................... 5
Supplied Hardware ...................................................................................................... 5
Installation ................................................................................................................... 5
Resources................................................................................................................................. 14
Reference Documents................................................................................................ 14
Further Inquiries ........................................................................................................ 14
Future Updates .......................................................................................................... 14
Return and Warranty Policies .................................................................................................. 15
Merchandise Returns / Repair Service ...................................................................... 15
CRESTRON Limited Warranty................................................................................. 15
Installation Guide – DOC. 6885A
Contents • i
Crestron MMK-V15 & WMKM-V15
Mud Mount Kits
Mud Mount Kits: MMK-V15 &
WMKM-V15
Description
Mud Mount Kits are the preferred mounting options for the Crestron V15-WALL
V-Panel 15” Wall Mount Touchpanel display when the cutout made in the drywall
for touchpanel installation is too large. It is also compatible with the WMKC-V15
V-Panel Wall Mount Conversion Kit. These kits provide support for additional
plastering that can be applied to hide large irregularities in the touchpanel cutout.
NOTE: If mounting into a material other than drywall (e.g., wood lectern, concrete
or rock) use the cutout template, available in the post-construction kit WMKM-V15.
For concrete and rock mounting material, allow for proper ventilation before
mounting the touchpanel.
There are two Mud Mount Kits. The MMK-V15 mud ring is an optional accessory
for the BB-V15 back box and PMK-V15 pre-construction mounting kit.
Pre-construction refers to framed walls prior to hanging drywall. It is designed to
compensate for drywall cutout imperfections, providing a grated surface suitable for
the application of drywall compound for a finished appearance.
The WMKM-V15 mounting kit provides a quick solution for installing a
V15-WALL V-Panel 15” Wall Mount Touchpanel display in an existing wall or
similar flat surface (e.g., lectern or podium). The WMKM-V15 is designed with a
mounting plate so that it can be mounted without the support of a stud. It is also
compatible with the WMKC-V15 Wall Mount Conversion Kit. Designed for
post-construction applications, the WMKM-V15 includes a MMK-V15 mud ring to
compensate for drywall cutout imperfections.
NOTE: The WMMK-V15 mounting kit requires at least a 17 inch (432 mm) wide
space behind the mounting surface.
NOTE: If necessary, consult the latest revision of the V15-WALL and WMKC-V15
Installation Guide (Doc. 6884) for a complete list of mounting options. This
document is available from the Crestron website (www.crestron.com/manuals).
Installation Guide – DOC. 6885A
Mud Mount Kits: MMK-V15 & WMKM-V15 • 1
Mud Mount Kits
Crestron MMK-V15 & WMKM-V15
The dimensions of the MMK-V15 and WMKM-V15 are shown below.
Overall Dimensions (Mud Ring Plate)
17.22 in
(438 mm)
12.94 in
(329 mm)
0.05 in
(2 mm)
0.50 in
(13 mm)
2.26 in
(58 mm)
Overall Dimensions (Adjustment Plate)
5.90 in
(150 mm)
0.38 in
(10 mm)
2 • Mud Mount Kits: MMK-V15 & WMKM-V15
Installation Guide – DOC. 6885A
Crestron MMK-V15 & WMKM-V15
Mud Mount Kits
Overall Dimensions (Mounting Plate)
17.00 in
(432 mm)
7.50 in
(191 mm)
11.74 in
(299 mm)
Installation Guide – DOC. 6885A
15.00 in
(381 mm)
13.00 in
(331 mm)
Mud Mount Kits: MMK-V15 & WMKM-V15 • 3
Mud Mount Kits
Crestron MMK-V15 & WMKM-V15
Overall Dimensions (Cutout Template)
12 in max
(306 mm max)
11 9/16 in
(294 mm)
Ø 1/4 in
(6.5 mm) TYP.
1/4 in
(6 mm)
7 3/8 in
(188 mm)
15 7/8 in max
(404 mm max)
4 • Mud Mount Kits: MMK-V15 & WMKM-V15
14 13/16 in
(376 mm)
1/4 in
(6 mm)
9/16 in
(14 mm)
Installation Guide – DOC. 6885A
Crestron MMK-V15 & WMKM-V15
Mud Mount Kits
Setup
Supplied Hardware
The MMK-V15 consists of three parts. These parts produce an assembly that
attaches to the BB-V15 or PMK-V15. The WMKM-V15 consists of six parts, three
of which make up the MMK-V15, as well as a mounting plate, cutout template and
mounting screws.
The mounting plate provides the necessary support for a touchpanel in an existing
wall or similar flat surface (e.g., lectern or podium) which can have joint compound
applied to it. An overlay cutout template (4508473) is supplied and is in the shape of
the required opening (refer to the illustration on page 4).
The hardware supplied with the MMK-V15 and WMKM-V15 is listed in the
following table.
Supplied Hardware for the MMK-V15 and WMKM-V15
DESCRIPTION
Metal, Bracket, Mud Ring
PART NUMBER
QUANTITY
2025107
1
Metal Plate, Adjustment
2004825
2
Hardware, Metal, Push-On Fasteners
2004121
4
Metal, Plate, Mounting
(WMKM-V15 only)
2024038
1
Overlay, Template, Wall Cutout
(WMKM-V15 only)
4508473
1
Screw, #06-32 x 1 1/2”, Pan, Phil:
(WMKM-V15 only)
2007254
6
Installation
This section provides an installation procedure for each Mud Mount Kit. The
“MMK-V15 Procedure” starts below and the “WMKM-V15 Procedure” starts on
page 9. Be sure to review each procedure before starting.
MMK-V15 Procedure
This section provides the necessary steps for the assembly of the MMK-V15 with
either the BB-V15 or PMK-V15. It is assumed that the BB-V15 or PMK-V15 has
been secured to the stud according to the instructions in the latest revisions of their
Installation Guides (Doc. 6801 and Doc. 6802 respectively). It is also assumed that
drywall is in place and a cutout is made in the drywall along the inside of the
mounting plate for touchpanel installation.
Complete the steps in the order provided. The only tools or materials required and
not supplied are four standard drywall screws, #2 Phillips screwdriver, a level and
tools/material to apply drywall joint compound.
CAUTION: Allow an air gap of at least 12 inches (305 mm) in the wall cavity
above and below the touchpanel for heat dissipation.
Installation Guide – DOC. 6885A
Mud Mount Kits: MMK-V15 & WMKM-V15 • 5
Mud Mount Kits
Crestron MMK-V15 & WMKM-V15
NOTE: The MMK-V15 has been optimized for mounting in 5/8” (15 mm) drywall.
You may use 1/2” – 1” (12.5 – 25 mm) without issue. Thinner or thicker drywall will
cause issues with the installation.
NOTE: The illustrations in this procedure show the installation of the MMK-V15
with the PMK-V15. Even though the illustrations only show the PMK-V15, the
procedure is identical for the BB-V15.
1.
Pass an adjustment plate through the opening and align its two center holes
with the top two pins on the PMK-V15 (or BB-V15). Verify that the pins on
the adjustment plate are not between (facing) the adjustment plate and the
PMK-V15 (or BB-V15). Refer to the illustration below for visual guidance.
Secure Adjustment Plates to PMK-V15 (or BB-V15)
PMK-V15
(2024092)
PUSH-ON FASTENER (4)
(2004121)
ADJUSTMENT PLATE (2)
(2004825)
2.
Slide a push-on fastener over each pin of the PMK-V15 (or BB-V15) to
loosely secure the adjustment plate and the mounting plate. Do not push the
push-on fasteners all the way down onto the pins. Slide them on enough to
keep the adjustment plate and mounting plate as one adjustment/mounting
plate assembly.
6 • Mud Mount Kits: MMK-V15 & WMKM-V15
Installation Guide – DOC. 6885A
Crestron MMK-V15 & WMKM-V15
3.
Mud Mount Kits
Use the second adjustment plate and repeat steps 1 and 2 using the lower
two PMK-V15 (or BB-V15) pins.
NOTE: When installing into the PMK-V15, verify that the 18 AWG bus
wire securing the cables for the touchpanel remains attached.
4.
Insert the symmetrical mud ring plate into the opening, as shown in the
illustration below.
Insert and Secure Mud Ring Plate into PMK-V15 (or BB-V15)
STUD
PMK-V15
DRYWALL
FLANGE
MUD RING
DRYWALL SCREWS
(NOT INCLUDED)
SCREW LENGTH SHOULD NOT
EXCEED DRYWALL
THICKNESS BY MORE
THAN 1/2" (13 MM)
5.
Installation Guide – DOC. 6885A
When the mud ring plate is in position, bend the top two flanges of the plate
upward and the bottom two flanges downward.
•
If mounting into the PMK-V15, bend the flanges approximately
90 degrees.
•
If mounting into the BB-V15, bend the flanges back as far as they can
go.
Mud Mount Kits: MMK-V15 & WMKM-V15 • 7
Mud Mount Kits
Crestron MMK-V15 & WMKM-V15
6.
Use four standard drywall screws (length should not exceed drywall
thickness by more than 1/2” (13 mm)) to secure the mud ring plate to the
rest of the assembly. The screws pass through the clearance holes in the
PMK-V15 (or BB-V15) and are secured in the extruded holes of the
adjustment plates.
7.
Verify that the mud ring plate is level.
NOTE: Do not overtighten screws. Doing so can rip the mud ring plate.
8.
Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that
they slightly dimple into the holes in the mud ring plate.
9.
Apply drywall joint compound as needed to finish the cutout. Avoid
covering the six tapped mounting holes.
10. Run the necessary cables for the touchpanel and secure them behind the
drywall.
11. When dry, the touchpanel can be installed using the six tapped holes in the
PMK-V15 (or BB-V15). Refer to the latest revision of the V15-WALL and
WMKC-V15 Installation Guide (Doc. 6884) for installation instructions.
Refer also to the comprehensive illustration shown on the following page.
8 • Mud Mount Kits: MMK-V15 & WMKM-V15
Installation Guide – DOC. 6885A
Crestron MMK-V15 & WMKM-V15
Mud Mount Kits
V15-WALL Mounting Using MMK-V15 (Exploded View)
PMK-V15
(2024092)
DRYWALL
V15-WALL
(not supplied)
BEZEL
MUD RING
(2025107)
SCREW (6), #06-32 x 1 1/2"
(2007254)
WMKM-V15 Procedure
This section provides the necessary steps for the assembly and installation of the
WMKM-V15 into a lectern, podium or furniture like cabinet. Review the procedure
and complete the steps in the order provided. The only tools or materials required
and not supplied are a saw or equivalent, a level, four application appropriate screws,
#2 Phillips screwdriver and tools/material to apply drywall joint compound.
CAUTION: Allow an air gap of at least 12 inches (305 mm) in the mounting
location above and below the touchpanel for heat dissipation.
NOTE: The WMKM-V15 has been optimized for mounting in 5/8” (15 mm)
drywall. You may use 1/2” – 1” (12.5 – 25 mm) without issue. Thinner or thicker
drywall will cause issues with the installation.
Installation Guide – DOC. 6885A
Mud Mount Kits: MMK-V15 & WMKM-V15 • 9
Mud Mount Kits
Crestron MMK-V15 & WMKM-V15
NOTE: Before installation, be sure to consider the needs of your particular
situation. For example, screw type may vary depending on the mounting surface, etc.
1.
Insert the two pins on one adjustment plate into the top two outer holes on
the mounting plate, as shown in the illustration below.
Create the Adjustment/Mounting Plate Assembly
MOUNTING PLATE
(2024038)
PUSH-ON FASTENER (4)
(2004121)
ADJUSTMENT PLATE (2)
(2004825)
2.
Slide a push-on fastener over each pin on the adjustment plate to loosely
secure the adjustment plate and the mounting plate. Do not push the
push-on fasteners all the way down onto the pins. Slide them on enough to
keep the adjustment plate and mounting plate as one adjustment/mounting
plate assembly.
3.
Use the second adjustment plate and repeat steps 1 and 2 using the lower
two holes of the mounting plate.
4.
Locate an area on the mounting surface that is free of miscellaneous wiring
and studs.
5.
Make a small hole near the middle of the designated site; verify that the
location is suitable.
10 • Mud Mount Kits: MMK-V15 & WMKM-V15
Installation Guide – DOC. 6885A
Crestron MMK-V15 & WMKM-V15
Mud Mount Kits
NOTE: Make the cutout as clean and level as possible. The mounting plate
allows for only minor leveling adjustments.
6.
Use the saw or equivalent and the provided cutout template to produce an
accurate and level cutout in the mounting surface.
7.
Insert the symmetrical mud ring plate into the opening, as shown in the
illustration below.
Insert Mud Ring Plate into Opening
MOUNTING
SURFACE
MUD RING
(2025107)
HOLES FOR
SCREWS (4)
(NOT INCLUDED)
NOTE: SCREW LENGTH SHOULD NOT
EXCEED MOUNTING SURFACE THICKNESS
BY MORE THAN 1/2” (13 MM).
Installation Guide – DOC. 6885A
8.
Carefully pass the adjustment/mounting plate assembly through the opening
and rest the assembly against the interior surface of the mounting surface.
Verify that the adjustment plates are between the mounting plate and the
mounting surface.
9.
When the adjustment/mounting plate assembly is in position, bend the top
two flanges of the mud ring upward (approximately 90 degrees) and the
bottom two flanges downward (approximately 90 degrees). Refer to the
illustration on the following page.
Mud Mount Kits: MMK-V15 & WMKM-V15 • 11
Mud Mount Kits
Crestron MMK-V15 & WMKM-V15
NOTE: Adjustment/mounting plate assembly will have slight play; this is normal. It
allows for minor adjustments to the entire assembly during installation.
Bend Flanges
10. Use four application specific screws (length should not exceed mounting
surface thickness by more than 1/2” (13 mm)) to secure the plate to the
adjustment/mounting plate assembly. The screws pass through the clearance
holes in the mud ring plate and are secured in the extruded holes of the
adjustment plates.
11. Verify that the plate is level before tightening.
NOTE: Do not overtighten screws. Doing so may damage the plate.
12. Use a #2 Phillips screwdriver and tighten the screws by hand so that they
slightly dimple into the holes in the mud ring plate.
13. Run the necessary cables for the touchpanel and secure them behind the
mounting surface.
12 • Mud Mount Kits: MMK-V15 & WMKM-V15
Installation Guide – DOC. 6885A
Crestron MMK-V15 & WMKM-V15
Mud Mount Kits
14. Apply joint compound as needed to finish the cutout. Avoid covering the
six tapped mounting holes.
15. When the joint compound is dry, the touchpanel can be installed using the
six tapped holes in the mounting plate. Refer to the latest revision of the
V15-WALL and WMKC-V15 Installation Guide (Doc. 6884) for
installation instructions. Refer also to the comprehensive illustration below.
V15-Wall Mounting Using WMKM-V15 (Exploded View)
PUSH-ON FASTENER (4)
(2024121)
ADJUSTMENT PLATE (2)
(2024825)
MOUNTING PLATE (2)
(2024038)
MOUNTING
SURFACE
V15-WALL
(not supplied)
BEZEL
Installation Guide – DOC. 6885A
MUD RING
(2025107)
SCREW (6), #06-32 x 1 1/2"
(2007254)
Mud Mount Kits: MMK-V15 & WMKM-V15 • 13
Mud Mount Kits
Crestron MMK-V15 & WMKM-V15
Resources
Reference Documents
The latest version of all documents mentioned within the guide can be obtained from
the Crestron website (www.crestron.com/manuals). This link will provide a list of
product manuals arranged in alphabetical order by model number.
List of Related Reference Documents
DOCUMENT TITLE
BB-V15 Wall Mount Back Box
PMK-V15 Pre-Construction Mounting Kit
V15-WALL and WMKC-V15 Wall Mount & Chassis Wall Mount Kit for V15
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling Crestron at 1-888-CRESTRON [1-888-273-7876].
You can also log onto the online help section of the Crestron website
(www.crestron.com/onlinehelp) to ask questions about Crestron products. First-time
users will need to establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features and extends the capabilities of
the MMK-V15 & WMKM-V15, additional information may be made available as
manual updates. These updates are solely electronic and serve as intermediary
supplements prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
14 • Mud Mount Kits: MMK-V15 & WMKM-V15
Installation Guide – DOC. 6885A
Crestron MMK-V15 & WMKM-V15
Mud Mount Kits
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number and
return address.
2.
Products may be returned for credit, exchange or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its
sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any
products returned with an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials
and workmanship under normal use for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and
overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if
any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a
third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are
limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names and trademarks are the sole property of their respective owners. Windows is a registered trademark
of Microsoft Corporation. Windows95/98/Me/XP/Vista and WindowsNT/2000 are trademarks of Microsoft Corporation.
Installation Guide – DOC. 6885A
Mud Mount Kits: MMK-V15 & WMKM-V15 • 15
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Installation Guide – DOC. 6885A
(2025226)
10.09
Specifications subject to
change without notice.