Bosch DIP-6082-8HD Installation guide

DIVAR IP 6000 2U
DIP-6080-00N, DIP-6082-8HD
en
Quick Installation Guide
DIVAR IP 6000 2U
Table of Contents | en
3
Table of contents
1
Safety precautions
4
1.1
General safety precautions
4
1.2
Electrical safety precautions
5
1.3
ESD precautions
6
1.4
Operating precautions
6
1.5
Important notices
7
1.6
FCC and ICES compliance
7
2
System overview
8
2.1
System interface
3
System setup - hardware
10
3.1
Introduction
10
3.2
Unpacking the system
10
3.3
Preparing for setup
10
3.3.1
Choosing a setup location
10
3.3.2
Rack precautions
10
3.3.3
General system precautions
11
3.3.4
Rack mounting considerations
11
3.4
Rack mounting instructions
12
3.4.1
Separating the sections of the rack rails
12
3.4.2
Installing the inner rails
13
3.4.3
Installing the outer rails to the rack
13
3.4.4
Installing the chassis into the rack
14
3.4.5
Installing the chassis into a Telco rack
15
3.5
Turning on the system
15
4
System Setup – first Steps
16
4.1
Introduction
16
4.2
Setup instruction
16
4.3
Setting the IP address
16
4.3.1
Remote desktop connection
16
4.3.2
Physical connection
19
4.4
VRM Appliance
21
4.4.1
Default installation
21
4.4.2
Disabling the VRM service
21
4.5
Standard system configuration
21
5
Additional software and documentation
22
6
Service and repair
23
Bosch Sicherheitssysteme GmbH
8
Quick Installation Guide
2013.05 | V3 | DOC
4
en | Safety precautions
DIVAR IP 6000 2U
Safety precautions
1
Observe the safety precautions in this chapter.
1.1
General safety precautions
Follow these rules to ensure general safety:
–
Keep the area around the system clean and free of clutter.
–
Place the chassis top cover and any system components that have been removed away
from the system or on a table so that they won't accidentally be stepped on.
–
While working on the system, do not wear loose clothing such as neckties and
unbuttoned shirt sleeves, which can come into contact with electrical circuits or be
pulled into a cooling fan.
–
Remove any jewelry or metal objects from your body, which are excellent metal
conductors that can create short circuits and harm you if they come into contact with
printed circuit boards or areas where power is present.
–
After accessing the inside of the system, close the system back up and secure it to the
rack unit after ensuring that all connections have been made.
–
The system weighs approximately 57 lbs. (25.9 kg) when fully loaded. When lifting the
system, two people at either end should lift slowly with their feet spread out to distribute
the weight. Always keep your back straight and lift with your legs.
Warning!
Interruption of mains supply:
!
Voltage is applied as soon as the mains plug is inserted into the mains socket.
However, for devices with a mains switch, the device is only ready for operation when the
mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the
socket, the supply of power to the device is completely interrupted.
Warning!
Removing the housing:
!
To avoid electric shock, the housing must only be removed by qualified service personnel.
Before removing the housing, the plug must always be removed from the mains socket and
remain disconnected while the housing is removed. Servicing must only be carried out by
qualified service personnel. The user must not carry out any repairs.
Warning!
Power cable and AC adapter:
!
When installing the product, use the provided or designated connection cables, power cables
and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire.
Electrical Appliance and Material Safety Law prohibits the use of UL or CSA-certified cables
(that have UL/CSA shown on the code) for any other electrical devices.
2013.05 | V3 | DOC
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
DIVAR IP 6000 2U
Safety precautions | en
5
Warning!
Lithium battery:
Batteries that have been inserted wrongly can cause an explosion. Always replace empty
!
batteries with batteries of the same type or a similar type recommended by the manufacturer.
Handle used batteries carefully. Do not damage the battery in any way. A damaged battery
may release hazardous materials into the environment.
Dispose of empty batteries according to the manufacturer's instructions.
Warning!
!
Handling of lead solder materials used in this product may expose you to lead, a chemical
known to the State of California to cause birth defects and other reproductive harm.
Notice!
Electrostatically sensitive device:
To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried
out correctly.
When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands
must be worn and the ESD safety precautions observed.
Notice!
Installation should only be carried out by qualified customer service personnel in accordance
with the applicable electrical regulations.
Disposal
Your Bosch product has been developed and manufactured using highquality materials and components that can be reused.
This symbol means that electronic and electrical devices that have reached
the end of their working life must be disposed of separately from
household waste.
In the EU, separate collecting systems are already in place for used
electrical and electronic products. Please dispose of these devices at your
local communal waste collection point or at a recycling center.
1.2
Electrical safety precautions
Basic electrical safety precautions should be followed to protect you from harm and the
system from damage:
–
Be aware of the locations of the power on/off switch on the chassis as well as the room's
emergency power-off switch, disconnection switch or electrical outlet. If an electrical
accident occurs, you can then quickly remove power from the system.
–
Do not work alone when working with high voltage components.
–
Power should always be disconnected from the system when removing or installing main
system components, such as the motherboard or memory modules. When disconnecting
power, you should first turn off the system and then unplug the power cords from all the
power supply modules in the system.
–
When working around exposed electrical circuits, another person who is familiar with the
power-off controls should be nearby to switch off the power if necessary.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
6
en | Safety precautions
–
DIVAR IP 6000 2U
Use only one hand when working with powered-on electrical equipment. This is to avoid
making a complete circuit, which will cause electrical shock. Use extreme caution when
using metal tools, which can easily damage any electrical components or circuit boards
they come into contact with.
–
The power supply power cords must include a grounding plug and must be plugged into
grounded electrical outlets. The unit has more than one power supply cord. Disconnect
both power supply cords before servicing to avoid electrical shock.
–
Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature
Coefficient) fuses on the mainboard must be replaced by trained service technicians only.
The new fuse must be the same or equivalent as the one replaced. Contact technical
support for details and support.
Caution!
Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside
!
down, which will reverse its polarities. This battery must be replaced only with the same or
an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries
according to the manufacturer's instructions.
Caution!
!
DVD-ROM Laser: This system comes without a DVD-ROM drive but if added: To prevent direct
exposure to the laser beam and hazardous radiation exposure, do not open the enclosure or
use the unit in any unconventional way.
1.3
ESD precautions
Electrostatic Discharge (ESD) is generated by two objects with different electrical charges
coming into contact with each other. An electrical discharge is created to neutralize this
difference, which can damage electronic components and printed circuit boards. The
following measures are generally sufficient to neutralize this difference before contact is made
to protect your equipment from ESD:
–
Do not use mats designed to decrease electrostatic discharge as protection from
electrical shock. Instead, use rubber mats that have been specifically designed as
electrical insulators.
–
Use a grounded wrist strap designed to prevent static discharge.
–
Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready
for use.
–
–
Touch a grounded metal object before removing the board from the antistatic bag.
Do not let components or printed circuit boards come into contact with your clothing,
which may retain a charge even if you are wearing a wrist strap.
–
Handle a board by its edges only. Do not touch its components, peripheral chips, memory
modules or contacts.
–
When handling chips or modules, avoid touching their pins.
–
Put the mainboard and peripherals back into their antistatic bags when not in use.
–
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and the
mainboard.
1.4
Operating precautions
The chassis cover must be in place when the system is operating to assure proper cooling. Out
of warranty damage to the system can occur if this practice is not strictly followed.
2013.05 | V3 | DOC
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
DIVAR IP 6000 2U
Safety precautions | en
7
Note:
Please handle used batteries carefully. Do not damage the battery in any way. A damaged
battery may release hazardous materials into the environment. Do not discard a used battery
in the garbage or a public landfill. Please comply with the regulations set up by your local
hazardous waste management agency to dispose of your used battery properly.
1.5
Important notices
Accessories - Do not place this unit on an unstable stand, tripod, bracket,
or mount. The unit may fall, causing serious injury and/or serious damage to
the unit. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer. When a cart is used, use caution and care when moving
the cart/apparatus combination to avoid injury from tip-over. Quick stops,
excessive force, or uneven surfaces may cause the cart/unit combination to
overturn. Mount the unit per the manufacturer's instructions.
1.6
FCC and ICES compliance
(only for U.S.A. and Canada)
This equipment has been tested and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the manufacturer’s instruction manual, may cause
harmful interference with radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case you will be required to correct the
interference at your own expense.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
8
en | System overview
2
DIVAR IP 6000 2U
System overview
DIVAR IP 6000 is an affordable, simple and reliable all-in-one recording management solution
for network surveillance systems of up to 64 cameras. Powered by VRM (Video Recording
Manager) software, the system is an intelligent IP storage device that eliminates the need for
separate NVR (Network Video Recorder) server and storage hardware.
The system is a 2U rack mount unit that combines advanced recording management and stateof-the-art iSCSI storage into a single cost-effective, plug and play IP recording appliance for ITminded customers seeking for a state-of-the-art “second generation” NVR recording solution.
DIVAR IP 6000 features:
–
Instant real time access to video
View high quality HD video despite low or limited bandwidth connections. Dynamic
Transcoding technology ensures that you can view your video immediately — anytime,
anywhere.
–
Remote viewing
DIVAR IP 6000 comes with our advanced Video Client for remote viewing. Video Client is a
Windows PC application for live viewing and playback including Configuration Manager.
Configuration Manager allows the settings of the DIVAR IP 6000 be configured. A standalone archive player will allow archive playback and authentication without any other
workstation software.
2.1
System interface
There are several LEDs on the front and rear of the chassis. The LEDs show the over-all status
of the system and the activity and health of specific components.
Front view:
2013.05 | V3 | DOC
1
Power Failure
5
Power
2
Overheat/Fan Fail
6
Reset
3
NIC1/NIC2
7
Power on/off
4
HDD
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
DIVAR IP 6000 2U
System overview | en
9
Rear view:
2
1
1
3
4
5
2x mains connection 100 – 240 VAC,
6
4
Serial interface COM1
50 - 60 Hz
2
2x PS/2
5
Monitor (VGA)
3
2x USB
6
2x Ethernet (RJ45)
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
10
en | System setup - hardware
DIVAR IP 6000 2U
3
System setup - hardware
3.1
Introduction
Scope of delivery:
–
DIVAR IP 6000 – 8-bay system, fully equipped with 8 hard drives (DIP‑6082‑8HD)
–
In addition to the system itself, the following items should have been shipped along with
each system
3.2
–
One rackmount kit
–
One AC power cable for each power supply in the system
–
This quick install guide
Unpacking the system
You should inspect the box the chassis was shipped in and note if it was damaged in any way.
If the chassis itself shows damage, file a damage claim with the carrier who delivered it and
notify the respective Bosch RMA desk.
You will also need it placed near at least one grounded power outlet.
Due to the weight of the system: After opening the top of the shipping box, one person should
stand at either end and lift the disk array out together.
Be sure to read the safety precautions.
3.3
Preparing for setup
The box the system is shipped in includes a rack mount kit, which you will need to install the
system into the rack.
Follow the steps in the order given to complete the installation process in a minimum amount
of time. Read this section before you begin the installation procedure outlined in the sections
that follow.
3.3.1
Choosing a setup location
–
Situate the system in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fields are generated. Place the system near a
grounded power outlet.
–
Leave approximately 25 inches clearance in front of the rack to be able to open the front
door completely.
–
Leave approximately 30 inches of clearance in the back of the rack to allow for sufficient
airflow and ease in servicing.
–
Install the system only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
Notice!
This product is not suitable for use with visual display work place devices acccording to §2 of
the the German Ordinance for Work with Visual Display Units.
3.3.2
Rack precautions
Warning!
!
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided
to ensure your safety:
2013.05 | V3 | DOC
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
DIVAR IP 6000 2U
System setup - hardware | en
–
11
Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor
with the full weight of the rack resting on them.
–
In single rack installations, attach stabilizers to the rack.
–
If the rack is provided with stabilizing devices, install the stabilizers before mounting or
servicing the unit in the rack.
–
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
–
When mounting this unit in a partially filled rack, load the rack from the bottom to the top
with the heaviest component at the bottom of the rack.
–
In multiple rack installations, couple the racks together.
–
Always make sure the rack is stable before extending a component from the rack.
–
Extend only one component at a time - extending two or more simultaneously may cause
the rack to become unstable.
3.3.3
General system precautions
–
Review the electrical and general safety precautions that came with the components you
are adding to your chassis.
–
Determine the placement of each component in the rack before installing the rails.
–
Install the heaviest components on the bottom of the rack first, and then work up.
–
Use a regulating uninterruptible power supply (UPS) to protect the system from power
surges, voltage spikes if you want to keep your system operating in case of a power
failure.
–
Allow the SATA hard drives and power supply modules to cool before touching them.
–
Always keep the rack’s front door and all panels and components on the system closed
when not servicing to maintain proper cooling.
See also
–
3.3.4
Safety precautions, page 4
Rack mounting considerations
Ambient operating temperature
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the
rack environment may be greater than the ambient temperature of the room. Therefore,
consideration should be given to installing the equipment in an environment compatible with
the manufacturer’s maximum rated ambient temperature (Tmra).
Reduced airflow
Equipment should be mounted into a rack so that the amount of airflow required for safe
operation is not compromised.
Mechanical loading
Equipment should be mounted into a rack so that a hazardous condition does not arise due to
uneven mechanical loading.
Circuit overloading
Consideration should be given to the connection of the equipment to the power supply
circuitry and the effect that any possible overloading of circuits might have on overcurrent
protection and power supply wiring. Appropriate consideration of equipment nameplate
ratings should be used when addressing this concern.
Reliable ground
A reliable ground must be maintained at all times. To ensure this, the rack itself should be
grounded. Particular attention should be given to power supply connections other than the
direct connections to the branch circuit (i.e. the use of power strips, etc.).
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
12
en | System setup - hardware
3.4
DIVAR IP 6000 2U
Rack mounting instructions
This section provides information on installing the chassis into a rack unit. There are a variety
of rack units on the market, which may mean the assembly procedure will differ slightly. You
should also refer to the installation instructions that came with the rack unit you are using.
Notice!
This rail will fit a rack between 26" and 33.5" deep.
3.4.1
Separating the sections of the rack rails
The chassis package includes two rail assemblies in the rack mounting kit. Each assembly
consists of two sections:
–
an inner fixed chassis rail that secures directly to the chassis
–
an outer fixed rack rail that secures directly to the rack itself.
To separate the inner and outer rails:
1. Locate the rail assembly in the chassis packaging.
2013.05 | V3 | DOC
2.
Extend the rail assembly by pulling it outward.
3.
Press the quick-release tab.
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
DIVAR IP 6000 2U
System setup - hardware | en
4.
3.4.2
13
Separate the inner rail extension from the outer rail assembly.
Installing the inner rails
The chassis includes a set of inner rails in two sections: inner rails and inner rail extensions.
The inner rails are pre-attached to the chassis, and do not interfere with normal use of the
chassis if you decide not to use a server rack. The inner rail extension is attached to the inner
rail to mount the chassis in the rack.
3
1
2
To install the inner rails:
1. Place the inner rail extensions on the side of the chassis aligning the hooks of the chassis
with the rail extension holes. Make sure the extension faces "outward" just like the preattached inner rail.
3.4.3
2.
Slide the extension toward the front of the chassis.
3.
Secure the chassis with 2 screws as illustrated.
4.
Repeat steps for the other inner rail extension.
Installing the outer rails to the rack
Outer rails attach to the rack and hold the chassis in place. The outer rails extend between 30
inches and 33 inches.
3
1
2
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
14
en | System setup - hardware
DIVAR IP 6000 2U
To install the outer rails to the rack:
1. Secure the back end of the outer rail to the rack, using the screws provided.
2.
Press the button where the two outer rails are joined to retract the smaller outer rail.
3.
Hang the hooks of the rails onto the rack holes and if desired, use screws to secure the
front of the outer rail onto the rack.
4.
Repeat steps 1-3 for the remaining outer rail.
Locking Tabs
Both chassis rails have a locking tab, which serves two functions. The first is to lock the
system into place when installed and pushed fully into the rack, which is its normal position.
Secondly, these tabs also lock the system in place when fully extended from the rack. This
prevents the system from coming completely out of the rack when you pull it out for servicing.
3.4.4
Installing the chassis into the rack
To install the chassis into a rack:
1. Extend the outer rails as illustrated above.
2.
Align the inner rails of the chassis with the outer rails on the rack.
3.
Slide the inner rails into the outer rails, keeping the pressure even on both sides. When
the chassis has been pushed completely into the rack, it should click into the locked
position.
4.
Optional screws may be used to secure the to hold the front of the chassis to the rack.
Warning!
!
Do not pick up the unit with the front handles. The handles are designed to pull the system
from a rack only.
Warning!
Stability hazard
!
Before sliding the unit out for servicing make sure that the rack stabilizing mechanism is in
place, or the rack is bolted to the floor. Failure to stabilize the rack can cause the rack to tip
over.
See also:
Rack precautions, page 10
2013.05 | V3 | DOC
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
DIVAR IP 6000 2U
3.4.5
System setup - hardware | en
15
Installing the chassis into a Telco rack
To install the chassis into a Telco type rack, use two L-shaped brackets on either side of the
chassis (four in total). First, determine how far the chassis will extend out the front of the
rack. Larger chassis should be positioned to balance the weight between front and back. If a
bezel is included on the chassis, remove it. Then attach the two front brackets to each side of
the chassis, then the two rear brackets positioned with just enough space to accommodate
the width of the Telco rack. Finish by sliding the chassis into the rack and tightening the
brackets to the rack.
3.5
Turning on the system
The last thing to be done is to provide input power to the system.
To turn on the system:
1. Plug the power cord from the power supply unit into a high-quality power strip that offers
protection from electrical noise and power surges. We recommended using an
uninterruptible power supply (UPS).
2.
Press the power button on the control panel to turn on the system.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
16
en | System Setup – first Steps
DIVAR IP 6000 2U
4
System Setup – first Steps
4.1
Introduction
The following installation directive provides information on Installation and Configuration.
The DIVAR IP 6000 systems are based on Windows Storage Server 2008 R2 operating system.
Windows Storage Server 2008 R2 systems provide a user interface for initial server
configuration, unified storage appliance management, simplified setup and management of
storage and shared folders, and support for Microsoft iSCSI Software Target.
It is specially tuned to provide optimal performance for network-attached storage. Windows
Storage Server 2008 R2 operating system provides significant enhancements in share and
storage management scenarios, as well as integration of storage appliance management
components and functionality.
4.2
Setup instruction
All systems are pre-configured with a default IP address and with default
iSCSI settings.
–
IP Address: 10.10.10.10 (1st port) and 10.10.10.11 (2nd port)
–
Subnet mask: 255.255.255.0
–
User: Administrator
–
Password: WSS4Bosch
The default iSCSI settings are optimized for use with VRM. Only an experienced storage
administrator should make changes to these settings.
Changing the default configuration is only required if:
4.3
–
VRM is not used (DIVAR IP 6000 as standard iSCSI disk array)
–
The default settings are not appropriate for another Bosch iSCSI application.
Setting the IP address
The default IP address can be changed as follows:
4.3.1
–
Remote desktop connection
–
Physical connection
Remote desktop connection
To start the system:
1. Connect the system to your network through port 1 or port 2 and start the system. The
system comes with the Remote Desktop Connection enabled. Log on to an appropriate
Client system either with Windows XP, Windows Vista or Windows 7 installed (Client
hardware and software is not part of the shipment) with an IP Address in the same
network, for example 10.10.10.12 (net mask: 255.255.255.0).
2013.05 | V3 | DOC
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
System Setup – first Steps | en
DIVAR IP 6000 2U
2.
17
Open the Remote Desktop Connection on your client system. In the Computer box, enter
the IP Address of the disk array you want to connect to.
Default IP Address: 10.10.10.10 (port 1)
3.
Click Connect, press Ctrl+Alt+Del (if shown), then type the default password WSS4Bosch
once the disk array login window is displayed.
To configure the IP address:
1. After starting the system, on first login the desktop default settings are applied. This will
take a few seconds and the system will reboot. After system reboot, log on again and the
Bosch VRM Appliance initial configuration window will be shown. Use this program to
configure the disk array’s IP Address.
2.
The top level view of Bosch VRM Appliance initial configuration displays an overview of
the system’s configuration and settings. Select the link Configure networking to get
access to the network configuration.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
18
en | System Setup – first Steps
DIVAR IP 6000 2U
For each network port a separate icon is shown. Select the Local Area Connection icon
that shows the status network, then double-click the icon.
3.
Click Properties, select Internet Protocol Version 4 (TCP/IPv4), then click Properties.
4.
This dialog box allows you to set the IP address configuration according to the
requirements of your network.
5.
2013.05 | V3 | DOC
Reboot the system.
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
DIVAR IP 6000 2U
4.3.2
System Setup – first Steps | en
19
Physical connection
To start the system:
The system comes with a VGA graphic connector and with PS2 connectors for mouse and
keyboard.
1.
Connect a monitor, mouse and keyboard (not part of the shipment) to the disk array and
start up the system.
Note:
When connecting a PS2 mouse or keyboard device after the system has been booted it
will most likely not operate properly.
2.
When the system has started up, press Ctrl+Alt+Del, then type the default password
WSS4Bosch once the disk array login window is displayed.
To configure the IP address:
1. After starting the system, on first login the desktop default settings are applied. This will
take a few seconds and the system will reboot. After system reboot, log on again and the
Bosch VRM Appliance initial configuration window will be shown. Use this program to
configure the disk array’s IP Address.
2.
The top level view of Bosch VRM Appliance initial configuration displays an overview of
the system’s configuration and settings. Select the link Configure networking to get
access to the network configuration.
For each network port a separate icon is shown. Select the Local Area Connection icon
that shows the status network, then double-click the icon.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
20
en | System Setup – first Steps
DIVAR IP 6000 2U
3.
Click Properties, select Internet Protocol Version 4 (TCP/IPv4), then click Properties.
4.
This dialog box allows you to set the IP address configuration according to the
requirements of your network.
5.
2013.05 | V3 | DOC
Reboot the system.
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
DIVAR IP 6000 2U
System Setup – first Steps | en
4.4
VRM Appliance
4.4.1
Default installation
21
The system is pre-installed with the Bosch Video Recording Manager (VRM) and fully licensed
with a 64 channel license. This license might be expanded by a maximum of another 64
channels.
VRM provides a powerful recording engine to be used with the Video Client or Bosch VMS for
live viewing and replay of recorded data. Video Client and Bosch VMS must be purchased
through the respective Bosch sales channels.
VRM Appliance offers a fully functional VRM recording solution only restricted in the number of
configurable channels. Applications that do not need the VRM software should disable the
VRM service.
4.4.2
Disabling the VRM service
If the system should be used as a standard iSCSI disk array, disable the VRM service.
To disable the VRM service:
1. Log on to the storage system, then start the Bosch VRM Appliance initial configuration
window. The top level view of the Bosch VRM Appliance initial configuration window
displays an overview of the system’s configuration and settings.
If the Bosch VRM Appliance initial configuration window is not displayed, click Start >
Run > oobe.
2.
Select the link Disable/Enable Bosch VRM Appliance to stop/start the VRM recording
service.
To restart the service again:
4 On the Bosch VRM Appliance initial configuration window, click the enable Bosch VRM
Appliance link.
See also:
Setting the IP address, page 16
4.5
Standard system configuration
The system is delivered with the fully configured iSCSI target and 8 preconfigured LUNs.
The default target name is TG0 and holds all of the iSCSILUNs.
The naming convention for the LUNs is VHDxx.vhd where <xx> ranges from 01 up to 08
depending on the system used. The default setup allows every iSCSI Initiator to connect to the
system.
The system comes with iSCSI Target Service enabled which is used by the pre-installed VRM
application.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
22
en | Additional software and documentation
5
DIVAR IP 6000 2U
Additional software and documentation
Software for configuration of hardware and software (VRM) is available on the VRM Appliance
in folder C:\Bosch\resources.
VRM Configurator: Software for easy configuration of VRM including disk array, cameras,
recording scheduler and other components. Should be installed on a separate Client system,
for example Bosch workstation hardware.
Notice!
For all viewing related configuration tasks (IVA, for example), the VRM configurator along with
the Bosch Video SDK (available from the Bosch web site) must be installed on a separate
client system.
Documentation for Bosch Security System products can be found as follows:
www.boschsecurity.com > select your region and your country > select Product Catalog >
start a search for your product > select the product in the search results to show the existing
documents.
2013.05 | V3 | DOC
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
DIVAR IP 6000 2U
6
Service and repair | en
23
Service and repair
The storage system is backed by a 3-year warranty. Issues will be handled according to Bosch
Support and Service guidelines. The standard Bosch support way of working applies.
The following modules may be replaced on-site in case of a failure without returning the unit:
–
Hard drives: As replacement hard drives only original Bosch hard drives are supported.
Otherwise the warranty is void. The replacement drives will come with the carrier
included.
–
Power supply: Only original Bosch replacement is supported.
–
Fan: Only original Bosch replacement is supported.
–
DOM: Disk on Module with the operating system image.
–
Chassis w/o hard drives: Fully equipped unit without the hard drives.
Request for RMA
Please request an RMA for failed parts from one of the following Bosch RMA contacts.
–
RMA Contact AMEC
Bosch ST, RMA Swapstock, 8601 East Cornhusker Hwy, Lincoln, NE 68507 -USA
Phone: +1(402)467-6610
Fax: n.a.
E-mail: repair@us.bosch.com
Opening Hours: Monday to Friday, 06:00 – 16:30
–
RMA Desk APR
Robert Bosch (SEA) Pte Ltd, 11 Bishan Street 21, (level 5, from service lift), Singapore
573943
Phone: +65 6571 2872
Fax: n.a.
Email: rmahelpdesk@sg.bosch.com
Opening Hours: Monday to Friday, 08:30 – 17:45
–
RMA contact China
Bosch (Zhuhai) Security Systems Co. Ltd. Ji Chang Bei Road 20#, Qingwan Industrial
Estate; Sanzao Town, Jinwan District, Zhuhai; P.R. China; Postal Code: 519040
Phone: +86 756 7633117 / 121
Fax: n.a.
Email: customer.service@cn.bosch.com
Opening Hours: Monday to Friday, 08:30 – 17:30
–
RMA Contact EMEA
Bosch Security Systems, C/o EVI Audio GmbH, Ernst-Heinkel Str. 4, 94315 Straubing,
GERMANY
Contact person: RA Desk Supervisor
Phone: +49(9421)706-366
Fax: n.a.
E-mail: rmadesk.stservice@de.bosch.com
Opening Hours: Monday to Friday, 07:00 – 18:00
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
2013.05 | V3 | DOC
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2013