Crestron IM-FTCC-B Installation guide

Crestron IM-FTCC-M
iMedia Fliptop Computer Center
Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2007 Crestron Electronics, Inc.
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
Contents
iMedia FlipTop Computer Center: IM-FTCC-M
1
Introduction ..........................................................................................................1
Features and Functions...........................................................................1
Applications ...........................................................................................3
Internal Block Diagram..........................................................................4
Specifications .........................................................................................4
Physical Description...............................................................................5
Industry Compliance ............................................................................10
Setup...................................................................................................................11
Network Wiring ...................................................................................11
IM Wiring ............................................................................................11
Installation............................................................................................12
Hardware Hookup ................................................................................17
Operation ............................................................................................................19
Problem Solving .................................................................................................20
Troubleshooting ...................................................................................20
Reference Documents ..........................................................................20
Further Inquiries...................................................................................21
Future Updates .....................................................................................21
Appendix: International Receptacles..................................................................22
Return and Warranty Policies.............................................................................23
Merchandise Returns / Repair Service .................................................23
CRESTRON Limited Warranty ...........................................................23
Operations & Installation Guide – DOC. 6610A
Contents • i
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
iMedia FlipTop Computer Center:
IM-FTCC-M
Introduction
Crestron's iMedia provides an extremely simple and affordable multimedia
presentation solution for small conference rooms and training rooms. No
comparable solution comes close to matching iMedia's speed and ease of
installation, intuitive operation, and incredibly low cost.
The IM-FTCC-M (120 VAC version) and the IMI-FTCC-M (220 VAC version)
are functionally identical, except for the power requirements. References
throughout the manual to the IM-FTCC-M apply equally to both units unless
specified otherwise.
Features and Functions
•
•
•
•
•
•
•
•
•
•
•
Flush-mount tabletop computer interface
Streamlined user controls for foolproof operation
iMedia Transport for fast and easy single cable installation
Supports XGA resolution up to 84 feet (25.6 m), UXGA
maximum up to 34 feet (10.4 m)
Easy pull-out cables and AC power outlet
One iMedia RJ-45 output connector (on the bottom side)
Power on/off SELECT button and indicator
Rotary volume control adjusts local level as well as level for
wireless microphone (wireless microphone input is located on the
IM-RXV1-M or IM-RXV3-M)
Lid flips open 180 degrees for easy access
Includes cable management kit with VGA and audio cables
Complete system setup in minutes using iMedia Wizard Software
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 1
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
The iMedia Transport
The iMedia (IM) transport utilizes a single CAT5e* type cable to transmit
computer RGB, video, and stereo audio signals to a single projector or plasma
display. A typical XGA signal (1024 X 768 pixels at 60 Hz) can be transmitted
up to 84 feet (25.6 m) using iMedia, while higher resolutions up to 1600 x 1200
can be handled over shorter distances. Audio is transmitted digitally at 20-bit, 48
kHz resolution. Control and power signals are also contained on the same wire,
eliminating the need for separate control or power cables.
* For optimum performance, Crestron strongly recommends using CRESCAT-IM cable,
available from Crestron. Other high-quality/low skew (15 ns per 100 m maximum)
CAT5e/CAT6 wiring may also be used with varying performance.
FlipTop Computer Interface
The IM-FTCC-M is an iMedia transmitter designed to install flush in a tabletop
surface to provide a convenient and low profile interface solution. Beneath the
"FlipTop" lid, a recessed compartment contains easy pull out RGB and audio
cables to facilitate the connection of a single computer source. The cables stow
neatly within the compartment when not in use. Excess cable simply drops out
of sight below the box through grommeted holes provided in the bottom plate.
An additional hole is available to accommodate a third party LAN cable if
needed.
For complete connectivity, the IM-FTCC-M also includes an AC power
receptacle. Installing wiring for the IM-FTCC-M is extremely simple requiring
just a single CresCAT-IM cable for audio and video. Up to three IM-FTCC-Ms,
or other IM transmitters, may be installed as part of a complete system to
provide multiple input locations within the room.
Foolproof Operation
Every iMedia system is easy and intuitive to use. A single press of the large
SELECT button inside the compartment lowers the screen or lift, turns on the
projector (or plasma, etc.) and routes the connected computer signal to the
appropriate input. The front panel volume control affords easy adjustment of the
audio level, or wireless microphone level, and the entire system can be turned
off at any time by simply holding the SELECT button for five seconds.
For systems having more than one IM transmitter, selecting an input at a given
input location overrides the previously selected input at any other location. The
audio level for each input location is controlled individually by its respective
volume control.
2 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
Applications
The IM-FTCC-B is an IM transmitter. As shown in the following diagram, IM
transmitters provide input points for video and PC sources on an IM receiver.
Typical Installation for Media Presentation (IM-FTCC-M is shown at Bottom)
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 3
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
Internal Block Diagram
The following diagram represents the signal routing and functions of the
IM-FTCC-M.
Internal Block Diagram of the IM-FTCC-M
VGA
BUTTON
SELECT
Microprocessor
Power
Power
Supply
IM
Output
LED
VOLUME
COMPUTER
AUDIO
A/D
Specifications
Specifications for the IM-FTCC-M are given in the following table.
IM-FTCC-M Specifications
SPECIFICATION
DETAILS
RGB
Gain
Formats
Resolution
0 dB (75 Ω termination)
RGBHV, RGBS, or RGsB
1024 x 768 @ 60 Hz with maximum cable
length of 84 feet, 1600 x 1200 @ 60 Hz with
maximum cable length of 34 feet; refer to “IM
Wiring” on page 11 for other resolutions
Audio
A-D Conversion
Frequency Response
20-bit, 48 kHz
20 Hz to 20 kHz ±1 dB
Power is provided by the IM receiver via the
IM transport
Power Requirements
Environmental
Temperature
Humidty
41º to 104º F (5º to 40º C)
10 to 90% RH (non-condensing)
Enclosure
Black metal; flush tabletop mountable
(Continued on following page)
4 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
IM-FTCC-M Specifications (Continued)
SPECIFICATION
DETAILS
Dimensions
IM-FTCC-M
Height
Width
Depth
4.63 in (11.76 cm) with lid closed
6.84 in (17.38 cm)
5.62 in (14.28 cm) without mounting brackets
IMI-FTCC-M
Height
Width
Depth
5.43 in (13.79 cm) with lid closed
8.34 in (21.19 cm)
6.20 in (15.74 cm) without mounting brackets
Weight
IM-FTCC-M
IMI-FTCC-M
3.65 lbs (1.66 kg) with cables
4.42 lbs (2.01 kg) with cables
International Adaptors for
IMI-FTCC-M Models
Refer to “Appendix: International
Receptacles” on page 22
Physical Description
This section provides information on the connections, controls and indicators
available on your IM-FTCC-M.
IM-FTCC-M Physical View
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 5
iMedia FlipTop Computer Center
IM-FTCC-M Open Top View
Crestron IM-FTCC-M
IMI-FTCC-M Open Top View
SELECT
IM-FTCC-M Physical Dimensions – Top View
IMI-FTCC-M Physical Dimensions – Top View
5.62 in
(14. 28 cm)
6. 20 in
(15.74 cm )
6.84 in
(17. 38 cm)
8. 34 in
( 21.19 cm)
IM-FTCC-M Physical Dimensions – Front View
IMI-FTCC-M Physical Dimensions – Front View
0.14 in
(0.36 cm)
4.49 in
(11.41 cm)
0.14 in
(0.36 cm)
Rests on
Table
Surface
5.38 in
(13.67 cm )
5.29 in
(13.44 cm)
6.88 in
(17.48 cm)
Power Cord
6 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
IM-FTCC-M Physical Dimensions – Side View
IMI-FTCC-M Physical Dimensions – Side View
4.19 in
(10.65 cm)
4.77 in
(12.11 cm)
Power Cord
IM-FTCC-M Front Face View
IMI-FTCC-M Front Face View
SELECT
1
2
1
3
IM-FTCC-M Bottom View
4
5
2
3
IMI-FTCC-M Bottom View
6
7
8
Operations & Installation Guide – DOC. 6610A
4
5
6
7
8
iMedia FlipTop Computer Center: IM-FTCC-M • 7
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
Connectors, Controls & Indicators
#
CONNECTORS,
CONTROLS &
INDICATORS
1
125VAC 10A
(1) 3-prong grounded AC socket, AC
power pass-thru outlet;
Maximum Load: 10 Amps @ 125 Volts
AC, 50/60 Hz.
250V 10A
(1) 3-prong grounded AC socket, AC
power pass-thru outlet;
Specify socket type (refer to “Appendix:
International Receptacles” on page 22);
Maximum Load: 10 Amps @ 250 Volts
AC, 50/60 Hz.
SELECT
(1) Pushbutton with green LED;
Momentary press initiates “system power
on” command and selects local
COMPUTER input; press and hold for 5
seconds or more initiates “system power
off”.
2
SELECT
DESCRIPTION
3
VOLUME
(1) Rotary knob, adjusts audio levels for
local input. Microphone level is adjusted
by holding the SELECT button and
turning the VOLUME knob.
4
125V
(1) 6 ft grounded AC line cord;
Passes through to front panel AC power
outlet.
MAX 250V
(1) IEC socket;
Passes through to front panel AC power
outlet.
5
AUDIO
(1) 3.5mm TRS mini phone jack;
Unbalanced stereo line-level audio input;
Maximum input level: 2 Vrms;
Input impedance: 10 kΩ;
Connects to 6 ft mini-TRS audio patch
cable (included).
6
IM1, 2, 3
(1) 8-wire RJ-45 female, iMedia output
port;
Connects to IM input port of an iMedia
receiver via CresCAT-IM cable.
(Continued on following page)
8 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
Connectors, Controls & Indicators (Continued)
#
CONNECTORS,
CONTROLS &
INDICATORS
7
COMPUTER
DESCRIPTION
PIN1
PIN6
PIN 15
8
GROUND
(1) DB15HD female, RGB(VGA) input;
Formats: RGBHV, RGBS, RGsB;
Input impedance: 75 Ω;
Sync impedance: 1 kΩ;
Maximum input level: 1 Vp-p;
Maximum sync level: 5 Vp-p;
Connects to 6 ft VGA patch cable (included).
PIN
FUNCTION
PIN
FUNCTION
1
Red Video
9
No Connect
2
Green Video
10
Ground
3
Blue Video
11
No Connect
4
Reserved
12
Monitor Sense 1
5
Ground
13
Horizontal Sync
6
Red Ground
14
Vertical Sync
7
Green Ground
15
Monitor Sense 2
8
Blue Ground
(1) 6-32 screw, chassis ground lug4.
1. The eight-pin RJ-45 iMedia port accepts CresCAT-IM or CAT5E/CAT6 carrying video, audio,
power and control signals. Refer to the following table for connector pinouts. Power is supplied to
pins 4 and 5 from the IM receivers.
PIN
WIRE COLORS (EIA 568B)
iMEDIA ASSIGNMENT:
RGB AND AUDIO
1
WHITE/ORANGE
- RGB RED
2
ORANGE
+ RGB RED
3
WHITE/GREEN
- RGB GREEN
4
BLUE
+ AUDIO / POWER
5
WHITE/BLUE
- AUDIO / POWER
6
GREEN
+ RGB GREEN
7
WHITE/BROWN
- RGB BLUE
8
BROWN
+ RGB BLUE
2. For optimum performance, Crestron strongly recommends using CRESCAT-IM cable, available
from Crestron. Other high-quality/low skew (15 ns per 100 m maximum) CAT5e/CAT6 wiring may
also be used with varying performance.
3. To determine which is pin 1 on the cable, hold the cable so that the end of the eight pin modular jack
is facing away from you, with the clip down and copper side up. Pin 1 is on the far left.
4. Ensure that the unit is properly grounded.
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 9
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
Industry Compliance
As of the date of manufacture, the IM-FTCC-M has been tested and found to
comply with specifications for CE marking and standards per EMC and
Radiocommunications Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
10 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
Setup
Network Wiring
When wiring the network, consider the following:
•
Use Crestron Certified Wire.
•
Use Crestron power supplies for Crestron equipment.
•
Provide sufficient power to the system.
CAUTION: Insufficient power can lead to unpredictable results or
damage to the equipment.
IM Wiring
Using a proprietary signal routing solution, RGBHV, audio, power and control
signals are all transported using a single cable solution called iMedia.
The iMedia transport system port is capable of managing computer RGB and
audio signals simultaneously through one CresCAT-IM cable, simplifying
installations.
Routing CresCAT-IM cable (low-skew CAT5e) is less expensive and a much
simpler solution for wiring iMedia systems than routing multi-colored,
multi-conductor coax cable. All Crestron products using the iMedia transport
system are capable of sending and receiving iMedia signals via CresCAT-IM
cable. Installation of any iMedia device is as simple as installing one iMedia
cable from output to input. Installations are affordable and fast.
The receiver can accomplish frequency compensation on each input to achieve
correct operation. This compensation scheme is effective for CresCAT-IM
cables as long as the maximum skew of 15 ns per 100 meters is not exceeded.
NOTE: For optimum performance, Crestron strongly recommends using
CRESCAT-IM cable, available from Crestron. Other high-quality/low skew
(15 ns per 100 m maximum) CAT5e/CAT6 wiring may also be used with
varying performance.
Maximum Resolution and Cable Length
RESOLUTION
VGA
(640 X 480)
SVGA
(800 X 600)
XGA
(1024 X 768)
REFRESH
RATE
(HZ)
PIXEL
RATE
(MHZ)
PIXEL
TIME (NS)
MAX
LENGTH
(FEET)
60
72
85
56
72
85
60
70
85
25.18
31.50
36.00
36.00
50.00
56.25
65.00
75.00
94.50
39.7
31.7
27.8
27.8
20.0
17.8
15.4
13.3
10.6
218.5
174.6
152.8
152.8
110.0
97.8
84.6
73.3
58.2
(Continued on following page)
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 11
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
Maximum Resolution and Cable Length (Continued)
RESOLUTION
REFRESH
RATE
(HZ)
PIXEL
RATE
(MHZ)
PIXEL
TIME (NS)
MAX
LENGTH
(FEET)
60
75
85
60
70
85
108.00
135.00
157.50
162.00
189.00
229.50
9.3
7.4
6.3
6.2
5.3
4.4
50.9
40.7
34.9
34.0
29.1
24.0
218.5
SXGA
(1280 X 1024)
UXGA
(1600 X 1200)
COMPOSITE
VIDEO
For more information on CresCAT and other wire products, visit the Crestron
website (www.crestron.com/downloads/pdf/product_line_overviews/overviewwire_and_cable.pdf).
Installation
NOTE: To prevent overheating, do not operate this product in an area that
exceeds the environmental temperature range listed in the table of specifications.
Consideration must be given if installed in a closed or multi-unit rack assembly,
inside a closed desk or in a closed podium since the operating ambient
temperature of these rack environments may be greater than the room ambient
temperature. Contact with thermal insulating materials should be avoided on all
sides of the unit.
Cable Management Kit
The IM-FTCC-M is shipped with a cable management kit that includes a cable
management plate, a 6-foot VGA cable, a 6-foot audio cable, and associated
hardware as listed in the following table.
Parts Supplied with Cable Management Kit
PART DESCRIPTION
QUANTITY
Small Cable Bushing, 5/16” ID, 0.5” OD
2
Large Cable Bushing, 0.55” ID, 0.80” OD
1
Cable Support Plate
1
4-40 x ¼ inch Phillips Head Screws
4
Computer RGB Cable, VGA to VGA, 6 ft long
1
Computer Audio Cable, 3.5 mm Stereo, 6 ft long
1
Tie Wraps
3
Complete the following instructions for installation.
Tools Required
•
Phillips screwdriver
•
Small flat blade screwdriver (for connecting the VGA cable)
The cable support plate must be installed before mounting the IM-FTCC-M to a
surface. The cables are looped through the cable support plate.
1.
Place the bushings on the cables (three bushings supplied). Use the
large bushing for the VGA cable.
12 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
2.
Thread the cables through the appropriate slots on the plate.
3.
Snap the bushings into the plate slots.
4.
Feed all the excess cable through the opening.
5.
Attach the plate using the four #4-40 x ¼” black screws.
6.
Connect the cables to the appropriate connectors on the bottom of the
IM-FTCC-M.
7.
The cables may be secured to the bottom bar using tie wraps.
Cable Plate Installation (IM-FTCC-M Shown)
Screws (4)
#4-40 x ¼”
Large Bushing
Small Bushing
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 13
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
Cable Loops Through the Cable Plate (IM-FTCC-M Shown)
Allow approximately
40 inches for cable clearence
RGB Cable
Audio Cable
Power Cord
NOTE: Ensure that the cables have sufficient clearance to enable smooth
movement. Allow approximately 40 inches (102 cm) from the top surface of the
FlipTop box mounting to surface.
Mounting to Surface
The IM-FTCC-M is designed to mount in a horizontal surface, such as a desk
top, lectern, or podium. The following diagram illustrates the required opening
size to accommodate the IM-FTCC-M. Use the supplied template to make the
cutout.
Cutout Dimensions for IM-FTCC-M (4007291)
6 5/16 in
(161 mm)
4 11/16 in
(118 mm)
Radius
1/8 in
(4 mm) Max
14 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
Cutout Dimensions for IMI-FTCC-M (4007909)
7 13/16 in
(198 mm )
5 1/8 in
(131 mm)
Radius
1/8 in
(4 mm )
NOTE: Before inserting the IM-FTCC-M in the mounting hole, ensure that all
required cables have been installed.
Mounting Parts Supplied with the IM-FTCC-M
PART DESCRIPTION
Screw #6-32, Pan Head, Phillips
QUANTITY
4
Screw #10-32, Pan Head, Phillips
4
Mounting Bracket
2
1.
Install the four supplied #6-32 screws, but do not tighten (four screws
on the rear are installed). All eight screws are used to secure the front
and rear mounting brackets.
2.
Position the IM-FTCC-M in the mounting hole.
Mounting Bracket Screw Locations
Screws
(4)
#6-32
Screws
#6-32 x 3/16“
Screws
(4)
#6-32
Screws
#6-32 x 3/16“
Surface
Surface
Cutout
Cutout
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 15
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
3.
Install the four #10-32 screws in the mounting brackets (two screws per
bracket). Refer to the following diagram.
4.
Slide the mounting brackets over the #6-32 screws and tighten the
#6-32 screws.
5.
Turn the four #10 screws equally until they contact the underside of the
mounting surface.
NOTE: Do not over-tighten the #10 screws as this may damage the surface
and/or the unit.
Mounting Bracket Installation
Mounting
Surface
Mounting
Bracket
Screws (2)
#10-32 x 2"
Mounting Bracket
Screws (2) #10-32 x 2"
Mounting Brackets Installed - IM-FTCC-M
6. 77 in
(17. 20 cm)
SCREWS (4) #10- 32 x 2"
SCREWS (8)
#6-32 x 3/16"
MOUNTING BRACKETS (2)
Mounting Brackets Installed - IMI-FTCC-M
SCREWS (4) #10- 32 x 2"
SCREWS (8) #6-32 x 3/16"
7. 34 in
(18. 64 cm)
MOUNTING BRACKETS (2)
16 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
Hardware Hookup
Make the necessary connections as called out in the illustration that follows this
paragraph. Apply power after all connections have been made.
When making connections to the IM-FTCC-M, consider the following:
•
Use Crestron power supplies for Crestron equipment.
•
The included cable cannot be extended.
Underside Connections (IM-FTCC-M Shown)
120 VAC LINE
CORD
(DOMESTIC MODELS
ONLY)
GROUND
(INTERNATIONAL
MODELS ONLY)
IEC-320
ELECTRICAL
APPLIANCE
COUPLER
AUDIO:
AUDIO INPUT
FROM
COMPUTER
IM:
iMEDIA OUTPUT
PORT CARRIES
RGB AND AUDIO
SIGNALS TO AN IM
RECEIVER
COMPUTER:
RGB INPUT
FROM
COMPUTER
Computer Connections (IM-FTCC-M Shown)
125 VAC POWER PASS-THRU
OUTLET
(DOMESTIC MODELS ONLY)
SELECT
(INTERNATIONAL MODELS
ONLY)
250 VAC POWER PASS-THRU
OUTLET
AUDIO:
CONNECT TO
COMPUTER
AUDIO OUPUT
COMPUTER:
CONNECT
TO COMPUTER
RGB OUTPUT
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 17
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
NOTE: For optimum performance, Crestron strongly recommends using
CresCAT-IM cables, available from Crestron. Other high-quality/low skew
CAT5e/CAT6 wiring may also be used with varying performance.
NOTE: Ensure that the unit is properly grounded.
NOTE: The maximum continuous current from equipment under any external
load conditions shall not exceed a current limit that is suitable for the minimum
wire gauge used in interconnecting cables. The ratings on the connecting unit's
supply input should be considered to prevent overloading the wiring.
System Configuration
Refer to the latest version of the IM-RXV1 & IM-RXV3 guide (Doc. 6478), or
the IM-RXV1-M & IM-RXV3-M guide (Doc. 6593), available from the
Crestron website (www.crestron.com/manuals) for iMedia system configuration
instructions.
18 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
Operation
The IM-FTCC-M can be used to turn a system on or off, adjust volume, or
adjust the microphone level.
Turn on the System
Press the SELECT button to turn on the system with the signals routed to the IM
receiver. The associated LED will light.
Adjust Volume
Turn the volume knob clockwise to raise the volume of the input; turn
counterclockwise to lower the volume of the input.
Adjust Microphone Level
The microphone level is adjusted by holding the SELECT button and turning the
rotary VOLUME knob.
When the SELECT button is released after adjusting the microphone volume
level, the source will remain at the same volume level it had prior to the
adjustment of the microphone volume.
Control over the computer audio volume level is regained by adjusting the rotary
VOLUME knob without holding down the SELECT button. The source volume
level will gradually ramp up or down to the level set by the rotary VOLUME
knob.
Turn off the System
Press and hold the SELECT button for five seconds. The source button LED will
flash and then turn off.
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 19
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble situations. If
further assistance is required, please contact a Crestron customer service
representative.
IM-FTCC-M Troubleshooting
TROUBLE
POSSIBLE
CAUSE(S)
CORRECTIVE
ACTION
SELECT LED
does not illuminate
when SELECT
button is pressed.
Not receiving power.
Verify that the iMedia
cable is properly attached.
No video output
displayed.
Incorrect cable
connection.
Verify computer cable
connection.
Verify iMedia output cable
connection is secure.
No audio output.
Incorrect cable
connection.
Verify computer audio
cable connection.
No Microphone
output.
Microphone level is
incorrectly set.
Set microphone level as
described on page 19.
Video from RGB
Incorrect cable
source is garbled or connections.
no output.
Verify 15-pin computer
cable connection. Verify
iMedia output cable
connections.
Verify maximum iMedia
cable length. Adjust delay
on IM receiver.
Button does not
function when
pressed.
Incorrect cable connection.
Verify that the iMedia
output cable connection is
secure.
Loss of functionality Improper grounding.
due to electrostatic
discharge.
Verify that all ground
connections have been
made properly.
Other functions
operate, but does
not control the
projector.
Verify cable wiring and
connections between
receiver and projector.
Incorrect connections to
projector.
Reference Documents
The latest version of all documents mentioned within the guide can be obtained
from the Crestron website (www.crestron.com/manuals). This link will provide
a list of product manuals arranged in alphabetical order by model number.
List of Related Reference Documents
DOCUMENT TITLE
IM-RXV1 & IM-RXV3 iMedia Receiver/Processor with Video
IM-RXV1-M & IM-RXV3-M iMedia Receiver/Processor with Video and Mic
Input
20 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team
by calling the Crestron corporate headquarters at 1-888-CRESTRON
[1-888-273-7876]. For assistance in your local time zone, refer to the Crestron
website (www.crestron.com/offices) for a listing of Crestron worldwide offices.
You can also log onto the online help section of the Crestron website
(www.crestron.com/onlinehelp) to ask questions about Crestron products. Firsttime users will need to establish a user account to fully benefit from all available
features.
Future Updates
As Crestron improves functions, adds new features and extends the capabilities
of the IM-FTCC-M, additional information may be made available as manual
updates. These updates are solely electronic and serve as intermediary
supplements prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 21
iMedia FlipTop Computer Center
Crestron IM-FTCC-M
Appendix: International Receptacles
PART
NUMBER
DESCRIPTION
COUNTRIES
6003287
6501271
PWR-AU-B POWER
RECEPTACLE,
AUSTRALIA, 250V,
10A, BLK
Australia, Fiji, New Zealand, Papua New Guinea
6003288
6501272
PWR-EU-B
POWER
RECEPTACLE,
EUROPE "SCHUKO",
250V, 16A, BLK
Austria, Azerbaijan, Belarus, Bosnia and Herzegovina, Brunei,
Bulgaria, Burundi, Cape Verde, Chad, Croatia, Czech Republic,
Egypt, Eritrea, Finland, Georgia, Germany, Greece, Greenland,
Guinea-Bissau, Hungary, Iceland, Jordan, Kazakhstan, Korea
(South), Kyrgyzstan, Liechtenstein, Luxemburg, Macedonia,
Monaco, Montserrat, Morocco, Mozambique, Netherlands,
Netherlands Antilles, New Caledonia, Norway, Poland, Portugal,
Reunion, Romania, Russia, San Marino, Senegal, Serbia and
Montenegro, Slovenia, Spain, Suriname, Sweden, Syria, Tunisia,
Turkey, Ukraine, Vietnam
6003289
6500643
PWR-IT-B
POWER
RECEPTACLE,
ITALY, 250V, 16A,
BLK
Chile, Ethiopia, Italy, Libya
6003290
6501273
PWR-UK-B
POWER
RECEPTACLE, UK,
250V, 13A, BLK
Anguilla, Bahrain, Botswana, Burma (Myanmar), Cyprus,
Dominica, Falkland Islands (Malvinas), Gambia, Ghana, Gibraltar,
Hong Kong, Iraq, Ireland, Kenya, Kuwait, Liberia, Malawi,
Malaysia, Malta, Mauritius, Nigeria, Northern Ireland, Oman,
Qatar, St. Kits-Nevis, St. Lucia, St. Vincent, Seychelles, Sierra
Leone, Singapore, Sudan, Tanzania, Uganda, United Arab
Emirates, United Kingdom, Yemen, Zambia, Zimbabwe
6003291
6501274
PWR-FR-B
POWER
RECEPTACLE,
FRANCE, 250V, 16A,
BLK
Algeria, Belgium, Cameroon, Central African Republic, Comoros,
Congo Democratic Republic, Djibouti, France, French Guiana,
Gabon, Guadeloupe, Guinea, Indonesia, Madagascar, Mali,
Martinique, Togo
NOTE: Installation instructions are included with all receptacles listed above.
22 • iMedia FlipTop Computer Center: IM-FTCC-M
Operations & Installation Guide - DOC. 6610A
Crestron IM-FTCC-M
iMedia FlipTop Computer Center
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the
factory and request an RMA (Return Merchandise Authorization) number. Enclose a note
specifying the nature of the problem, name and phone number of contact person, RMA
number and return address.
2.
Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight
collect or without an RMA number shall be subject to refusal. CRESTRON reserves the
right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs,
on any products returned with an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by
CRESTRON, shipping by standard ground carrier. In the event repairs are found to be nonwarranty, return freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in
materials and workmanship under normal use for a period of three (3) years from the date of purchase
from CRESTRON, with the following exceptions: disk drives and any other moving or rotating
mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen
display and overlay components are covered for 90 days; batteries and incandescent lamps are not
covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if
any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended, or if it has been subjected to misuse, accidental
damage, modification, or improper installation procedures. Furthermore, this warranty does not cover
any product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic
damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim
made by a third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by
the unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law
are limited to the terms of this limited warranty. This warranty statement supersedes all previous
warranties.
Trademark Information
All brand names, product names and trademarks are the sole property of their respective owners. Windows is a registered
trademark of Microsoft Corporation. Windows95/98/Me/XP/Vista and WindowsNT/2000 are trademarks of Microsoft Corporation.
Operations & Installation Guide – DOC. 6610A
iMedia FlipTop Computer Center: IM-FTCC-M • 23
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Operations & Installation Guide DOC. 6610A
(2018825)
09.07
Specifications subject to
change without notice.