DEUTSCHER TH910 Series II Owner`s Manual

DEUTSCHER
TH910
Series II
Ride-on mower
Owner’s Manual
Part No. T961
Edition: 1
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23
24.
25.
26.
27.
28.
29.
30.
31.
32.
SAFETY INSTRUCTIONS:
Know your controls. Read the operator manual carefully. Learn how to stop the engine quickly in any
emergency.
Do not allow children or people unfamiliar with these instructions to use the mower. Do not carry
passengers.
Make sure the area to be cut is clear of sticks, stones, bones, wire and debris. The blades could throw
them.
Do not mow whilst people, especially children or pets are in the area.
Never mow across a slope unless the mower is designed for this purpose.
Exercise extreme caution when on slopes. Reduce speed on slopes and in sharp turns to prevent
overturning or loss of control. Do not start suddenly when going uphill or down hill.
Stay alert for holes in the terrain and other hidden hazards.
Use care when pulling heavy loads or use heavy equipment.
a. Use only approved drawbar hitch point.
b. Limit loads to those you can safely control.
c. Do not turn sharply.
d. Use care when backing up.
Watch out for traffic when crossing or operating near roadways.
Stop blades rotating before crossing surfaces other than grass.
When blades are engaged never direct discharge of materials towards by bystanders or allow anyone near
the machine while it is in operation.
Before leaving the operator's position:
a. Disengage cutter clutch.
b. Ensure the parking brake is engaged.
c. Stop the engine and remove the ignition key.
Stop the engine and disengage the cutter clutch:
a. Before refuelling.
b. Before clearing blockages.
c. After hitting a foreign object (inspect the mower for damage and make
repairs before restarting and operating the equipment).
d. Before checking, cleaning or working on the mower.
e. if the machine starts to vibrate abnormally (check immediately).
The mower operator should be in good physical and mental condition and not under the influence of any
drug or alcohol, which might impair vision, co-ordination or judgement.
Never mow while barefoot or wearing open sandals or thongs, wear long trousers and heavy shoes.
It is advisable to wear suitable eye protection when operating the mower.
Mow only in good daylight.
Before using the mower always visually inspect to see that the blades, bolts and cutter assembly are not
worn or damaged. Replace worn or damaged blades in sets to preserve balance.
Check all nuts, and bolts often, always be sure the mower is in a safe working condition.
Keep safety devices (guards and switches) in place and in working order.
Never use the mower unless all guards provided by the manufacturer are in position.
Ensure any spare parts used comply with the original manufacturer's recommendations and specifications.
Replace worn and faulty silencers.
Keep engine free of grass, leaves or excessive grease. These can be a fire hazard.
Refuel outdoors only. Do not smoke while refuelling engine. Never remove the cap of the fuel tank or add
fuel while the engine is running or the engine hot. Remove the fuel cap slowly to relieve any tank pressure.
If petrol is spilled, do not attempt to start the engine but move machine away from the area of the spill and
avoid creating any source of ignition until petrol vapours have dissipated.
Check for fuel leaks while refuelling or using the mower. If a fuel leak is found, do not start or run the
engine until the fuel leak is fixed and spilled fuel wiped away.
Do not operate the mower in a confined space where exhaust fumes (carbon monoxide) can collect.
Always mount the mower on the opposite side to the discharge chute.
Start the engine carefully with the cutting clutch disengaged.
Store the mower in a well ventilated area away from naked flames.
Stop the engine when ever you leave the mower, even for a moment.
Do not lend or sell the mower without the Owner's Manual.
2
SPECIFICATIONS:
ENGINE:
Fitted with either: Briggs & Stratton model 28N707 Diamond Plus series, 15.5 hp.
Honda model GXV390K1, 13 hp.
TRANSMISSION:
Hydro-Gear hydrostatic transaxle model 310-0800 IHT commercial qualified.
Speed range, variable 0 to 10 kph.
CUTTING HEAD:
Fabricated 2.5mm steel cutting deck with twin blade plates and blades,
Cutting width 910mm
Height of cut: 30mm to 90mm with 8 variations.
TYRES:
Front 13-500-6
Rear 18-850-8
140 kpa pressure
70 kpa pressure
CONTROLS:
Throttle – mounted on left hand side of control panel marked with SLOW, FAST and CHOKE positions.
Key Ignition – mounted on right hand side of control panel, marked with ON, OFF and START positions.
Transmission Lever – mounted on the left hand side of the control panel with ON, OFF positions.
Parking Brake – mounted on the left hand side of the mower near the seat.
Cutter Drive Engagement Lever – located centre of mower in front of seat
Height control lever – mounted on the right hand side of cutter deck, 8 positions.
Drive Pedal – located on the right hand side of the control panel, variable speed in both forward and
reverse direction and returns to neutral position when your foot is not on the pedal.
GENERAL:
Length: 1820mm, width: 990mm, height: 1080mm, weight: 230kg.
PRE-START CHECK:
Your Deutscher Ride-on Mower comes to you tested and ready to operate with engine and transaxle filled
with oil.
1:
Read all safety instructions and know how to stop engine quickly in any emergency.
2:
Know your controls – where they are and there function.
3:
Use fresh clean unleaded petrol. Do not mix oil with petrol.
4:
Adjust the seat to best suit the operator.
SAFETY INTERLOCK SYSTEM:
The safety interlock system has been designed for the operator’s safety and should never be tampered
with.
3
OPERATION:
STARTING THE ENGINE:
1:
2:
3:
4:
5:
6:
Operator must be seated, as to activate safety switch.
Move transmission lever to OFF position.
Move cutter engagement lever to the DISENGAGED position.
For cold start move throttle lever to CHOKE position, (warm start to FAST position).
Turn key to start.
When engine starts, move throttle lever to desired engine speed.
TO DRIVE MOWER:
1:
2:
3:
1:
2:
3:
Move transmission lever to ON position.
Release parking brake.
Place foot on drive pedal and apply pressure with ball of foot to go forward or heel of foot on the
back part of pedal for reverse.
The following tips will assist control of the mower and reduce the risk of damage or accidents:
Always operate the pedal smoothly when moving off and when coming to a stop.
Always keep your foot on the pedal when stopping. Lifting your foot will cause the machine to stop
suddenly and throw you forward or backwards (depending on the direction you are travelling).
Always pause in neutral when changing from forward to reverse or reverse to forward.
CUTTER ENGAGEMENT:
1:
2:
Move throttle lever to approximately two thirds engine speed.
Slowly move cutter drive lever forward to engage cutter clutch.
IMPORTNANT: When engaging or releasing cutter drive lever, always operate slowly. Do not use
fast or jerking motion as this will overload the engine causing it to stall.
MAINTENANCE:
ENGINE:
1:
2:
3:
4:
Refer engine manual.
To change oil, start and run engine until operating temperature to warm oil.
Fit a drain tube to engine drain fitting.
Open the drain fitting two turns only and allow oil to drain completely.
Re-tighten the drain fitting and refill engine with oil to correct level as per engine manual.
TRANSAXLE: The transaxle fitted to the mower normally will not require servicing during the life of the mower.
Should the transaxle require attention, it should only be carried out by technically qualified person.
It is important that you keep the unit clean from grass clippings, oil, and dirt etc. Avoid high
pressure cleaning. If cooling fan is broken or damaged, it should be replaced immediately.
BLADES:
It is important that you visually inspect the blades, blade bolts and nuts to ensure that they are in a
safe operating condition. Replace all components in sets to retain balance of blade plate.
OFF SET NUT
TO CHANGE BLADES:
CURVED WASHER
ROTATION
1:
2:
3:
4:
5:
Ensure ignition switch is in the OFF position.
Un-screw off set nut and remove curved washer.
Blade and bolt are removed from underneath
blade plate.
Inspect parts for wear or damage and replace.
Replace by reversing the above procedure, make sure
the blade is fitted underneath the blade plate. Screw on off set nut
until nut is level with the top of the bolt, and ensure that the offset of the
nut is facing out.
4
Fig.1
BLADE
BLADE PLATE
BOLT
BELT ADJUSTMENTS:
CENTRE SPINDLE BELT: Fig.2
1:
2:
Place height lever in mid position.
Loosen nut “A” and tighten nut “B” (Fig.2)
20mm
TRANSAXLE BELT:
1:
2:
3:
4:
Loosen the four engine mount bolts.
Slide engine forward along slots.
Re-tighten the engine mount bolts.
Adjust centre spindle belt as above.
WARNING! DO NOT OVER TIGHTEN BELTS.
CUTTER SPINDLE BELTS: (Fig.3)
1:
2:
3:
CD
Fig.2
Loosen nut “C”.
Push jockey pulley ”D” against belt until tight.
Tighten nut “C”.
Fig.3
E
C
D
A
B
E
D
C
REPLACING BELTS:
CENTRE SPINDLE BELT: Fig.2
1:
Uncouple seat switch wire (Bullet connector at rear of seat).
2:
Remove seat panel.
3:
Set cutting deck in mid cutting height position.
4:
Remove belt guide at rear of pulley.
5:
Loosen Nut "B" so that main belt is loose.
6:
Loosen all engine mounting bolts.
7:
Push engine to rear of mower and remove transmission belt.
8:
Remove belt from pulleys and replace.
9:
Fit transmission belt.
10:
Loosen nut "A" till main drive belt is tensioned and tighten nut "B".
11:
Tighten engine bolts and replace belt guide.
TRANSMISSION BELT: Fig.2
1:
Uncouple seat switch wire (bullet connector at rear of seat)
2:
Remove seat panel
3:
Remove fan cover from rear of engine
4:
Loosen nut "B" so that main belt is lose
5:
Loosen all engine mounting bolts and pushing engine back on slots
6:
Remove belt off engine pulley first then transmission pulley.
7:
Fit new belt over transmission pulley then onto engine pulley.
8:
Loosen nut "A" till centre belt is tensioned (it will also tension transmission belt) and tighten nut "B".
9:
Tighten all engine mounting bolts and refit panels.
5
CUTTER SPINDLE BELTS: Fig.3
1:
Uncouple seat switch wire (bullet connector at rear of seat)
2:
Remove seat panel
3:
Remove belt guide from rear of pulley
4:
Loosen nut "B" and remove main drive belt
5:
Remove covers over cutter spindles
6:
Position clutch laver in engaged position
7:
Remove four "R" clips
8:
Remove clutch bars
9:
Loosen nuts on brake and turn plate sideway ⅛ turn to allow clearance for belts to slip through.
(Do not loosen ⅝ nuts)
10:
Replace belts and reassemble.
CLUTCH ADJUSTMENT: Fig.3
1:
2:
3:
Loosen nut ”E”.
Tighten nut underneath square block (1/2 turn should be sufficient).
DO NOT OVER ADJUST, clutch should have .75mm gap between clutch lining and pulley surface
when in brake position.
Ensure nut “E” tight when adjusted.
Fig.5
Fig.4
OIL
GREASE
LUBRICATION CHART:
GREASE
Engine
As per engine manual
Grease king pins
20 hours
Grease front axle pivot, fig.4
20 hours
Grease vertical gear steering gear shaft, fig.4
20 hours
Grease cutter spindles & clutch spindle, fig.5
20 hours
Oil steering wheel shaft (top & bottom), fig. 4
20 hours (oil)
Grease steering gears, fig.4
20 hours (smear with grease)
Oil all moving parts
20 hours
6
REPLACING BEARINGS IN CUTTER SPINDLES:
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
Remove pulley guard.
Remove lock nuts from on top of pulleys
Remove pulley and washer
Spindle and flange will push out under cutter deck.
Remove bearings and spacer sleeve and clean all parts.
Press bottom bearing into housing
Fit spindle and flange to bottom bearing in housing.
Insert spacer sleeve
Wipe clean top bearing and area which locates bearing with an oil solvent.
Apply "Loctite" to top bearing and housing and press firmly into housing.
Fit top spacer washer and pulley and tighten assembly together with lock nuts.
Do not grease until "Loctite" is cured. (12 Hours)
REPLACING BEARINGS FOR CENTRE SPINDLE BEARINGS:
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
15:
16:
17:
18:
Remove seat panel and cutting deck from mower,
Undo top nut on top of spindle and remove stepped bushes and top pulley,
Remove clutch bars by removing R-clips,
Undo nuts on brake plate and turn 90 degrees and push down clutch assembly down to expose
clutch gear,
Remove clutch gear and key in shaft and remove brake assembly,
Remove dust cap from bottom of housing and undo nut on spindle,
Remove spindle from housing and press out bearing outer rings,
Clean all parts in replace any defective parts,
Press bearing outer rings into each end of spindle housing.
Fit bearing, seal washer, double pulley, and 2 nuts to spindle and tighten,
Place spindle into housing,
Place bottom bearing over spindle and screw on special nut using ”Loctite”.
Adjust bearing, and lock by forcing nut rim into keyway with centre punch,
Press dust cap on to base of spindle housing securing with "Loctite", and grease bearings.
Fit brake assembly over spindle, then fit key, clutch gear and clutch bars,
Move brake into brake position,
Place stepped bushes each side of pulley, fit pulley to spindle and tighten nut,
Fit cutter belt and guide.
REMOVE CUTTER DECK: Fig.2
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
Turn ignition key off and remove.
Place transmission lever In “OFF” position.
Uncouple seat switch (blade connector at rear of seat) and remove seat panel.
Raise cutter deck to highest position.
Uncouple the two wires from safety switch.
Remove rod “C”.
Remove rod “D”
Remove rear locating nut “E” and washer.
Remove belt from pulley.
Lift chassis clear of deck and wheel mower backwards.
NOTE: Blades can be changed with out removing cutting deck. R.H. blades are accessible through the
side chute. L.H. blades can be replaced by elevating the front of the mower 300mm.
7
WHEN ORDERING PARTS
SPECIFY THE MODEL AND SERIAL NUMBER
ON THE NAME PLATE OF THE MOWER
AND THE PART NUMBER IN THIS MANUAL
PART No
DESCRIPTION
T914
T920
T201
T202
Decal set
Paint, 150g pressure can, Hawthorn Green
Oil drain valve, B&S
Oil drain valve, Honda
THE MANUFACTURERS RESERVE THE RIGHT TO ALTER, CHANGE OR VARY THE
SPECIFICATIONS OF THE MACHINE OR ANY OF THE COMPONENT PARTS
AT ANY TIME WITH OUT NOTICE
8
5
2
1
1
2
3
14
12
32
7
8
1
10 11
9 8
30
18
15
19
16
20 21 22
18
23
4
28
17
2
29
31
25
27
24
26
ILLUS.
PART No
DESCRIPTION
ILLUS.
PART No
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
T720
T567
T721
T722
T723
T724
T581
T725
T726
H08
H07
R282
R281
R280
T727
T728
T200
Chassis
Ball joint, 3/8”
Pivot arm
Speed rod & ball ends
Battery strap
Bolt, battery strap x 2
Pedal
Bush x 2
Washer
Pin x 2
Roller, nylon x 2
Tank strap x 2
Cap, fuel tank
Fuel tank, 6lt
Tank bracket
Fan cover
Engine pulley
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
T510
HD124
T527
T435
T508
T729
T511
T730
Y03
T731
R87
T732
T733
T734
T735
Nut, adjustment 5/8”w x 2
Spring washer
Washer
Swivel link
Pivot bush
A-frame
Flanged bush x 2
Spring x 2
Spring
Pivot assembly
Spring
Pivot bolt & nut
Lever, park brake
Rod, park brake
Roll pin
9
1
11
22
8
44
3
15
5
6
5
15
6
9 10
14
15
16
13
14
15
7
25
26 27 12
15
17 21
18
17
19
28
20
15
2
23 26
22 14
24
ILLUS.
PART No
DESCRIPTION
ILLUS.
PART No
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
T550
T552
T554
T551
T557
T574
T558
T560
T561
T553
T513
R100
T528
R92
R91
T566
Steering wheel
Top bearing
Roll pin
Steering column & gear
T-knob x 2
Lever assembly x 2
Cable, universal x 2
Panel
Hinge pin x 2
Bottom bearing
Steering spindle & gear
Cap x 2
Drag link & set screw
Collar x 3
Bush x 8
Axle beam
17
18
19
20
21
22
23
24
25
--26
27
28
R93
MR90
MR95
T568
T567
T524
R87
T570
T562
T563
T564
T588
RD174
H514
Thrust washer x 2
King pin & stub axle L.H.
King pin & stub axle R.H.
Front tie rod & ends
Ball ends 3/8”unf x 2
Grease nipple 45o
Spring x 2
Rear tie rod assembly
Wheel assembly
Tyre 13-500-6
Tube 13-500-6
Bearing, 6203 x 2
Nut 5/8”unf x 2
Spacer, bearing
10
13
11
12
4
9
10
2
3
1
7
8
5
6
ILLUS.
PART No
DESCRIPTION
ILLUS.
PART No
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
T150
T161
70110
70109
Y03
T164
T154
T558
T152
T153
Hydro-gear IHT310-0800
Hose, breather
Fitting, hose #
Cap, vent assembly #
Spring
Neutral bracket assembly
Key 3/16”
Cable, universal
Hub & set screw
Cirlip x 2
11
12
13
------
T108
T155
T112
T113
T114
T115
T136
T137
Wheel nut x 8
V-belt, A32
Wheel assy. turf
Rim
Tyre, turf, 18-850-8
Tube, 18-850-8
Wheel assy. Knobby
Tyre, Knobby, 18-950-8
NOTE: Parts marked # are to be sourced from an Authorised Briggs & Stratton Dealer
11
1
2
3
5
4
8
9
11
7
6
10
ILLUS.
PART No
DESCRIPTION
ILLUS.
PART No
DESCRIPTION
1
2
3
4
5
6
7
T530
T541
T534
T533
T711
T712
D134
T713
Seat
Back rest, optional
Hinge bracket R.H.
Hinge bracket L..H.
Seat base
Seat panel
Spring
Strap, earth
8
9
10
11
DD111
T535
T536
T714
Washer
Spring
Spring cap
Bush x 2
12
4
9
10
8
2
4
3
1
5
11
12
6
7
ILLUS.
PART No
DESCRIPTION
ILLUS.
PART No
DESCRIPTION
1
2
3
4
5
6
7
T433
T442
T741
T633
T440
T439
D50
Pin 5/8”
Link bracket
Washer
R-clip
Crank arm
Rod, connecting
Spring
8
9
10
11
12
T434
T435
T441
T742
T431
Link pin
Swivel link
Collar 5/8”
Sub frame & deflector
Deflector
13
17
3
18
1
4
6
2
16
5
7
8
11
13
12
9
10
14
15
14
ILLUS.
PART No
DESCRIPTION
ILLUS.
PART No
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
T700
T401
Y13
T701
T402
T403
T415
T702
T411
T703
T704
Cutter deck
Side chute
Knob
Lever, raise & lower
Pulley guard L..H.
Pulley Guard R.H.
Height rack
Spring
Rear mount assembly
Cross bar
Pivot bush, threaded
12
13
--14
15
16
17
18
T705
Y555
Y557
Y556
T588
Y558
T640
T641
T618
Pivot bolt
Wheel assembly
Tyre
Rim assembly
Bearing 6202 x 2
Bolt & washer
Bracket L.H. pulley, high
Bracket R.H. pulley, low
Pulley x 2
14
1
7
2
8
3
4
14
5
13
15
6
4
9
10
12
11
ILLUS.
PART No
DESCRIPTION
ILLUS.
PART No
DESCRIPTION
1
2
3
4
5
6
7
8
9
G30
T454
T452
R28
T451
T453
R13
T450
R32
Lock nut x 2
Pulley x 2
Washer x 2
Bearing, 6205 x 4
Sleave x 2
Housing x 2
Grease nipple x 2
Spindle & flange x 2
Blade plate x 2
10
11
12
13
14
15
G36
D02
R01
D04
D03
T432
Bolt & spring washer x 6
Bolt, blade x 4
Blade x 4
Washer, blade x 4
Nut, blade x 4
V-belt, B32 Dayco super 2 x 2
15
20
1
21
22
5
6
23
22
7
2
24
25
8
9
26
10
12
1
1
3
12
12
1
4
28
27
29
30
16
14
17
9
31
11a
15
16
18
19
15
ILLUS.
1
2
3
4
5
6
7
8
9
10
11
11a
12
13
14
15
16
17
PART No
Y13
T654
T623
T624
T610
G30
T600
T636
G33
T655
T638
T639
T628
T627
T626
T633
T630
T656
DESCRIPTION
Knob
Lever, engagement
Eye bolt adjuster
Pivot Bolt
Clutch drive gear
Lock nut x 2
Double pulley
Seal washer
Bearing x 2
Woodruff key
Spindle & bottom lock nut
Lock nut
Stud, adjustment x 2
Side strap R.H.
Side strap L.H.
R-clip x 4
Spring x 2
Main housing
ILLUS.
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
---16
PART No
T622
T629
T608
T604
T602
T603
T651
T652
RD105
T653
T612
T614
T613
T634
T657
T309
Y41
R13
DESCRIPTION
Cap, bottom housing
Pin
Nut
Circlip, 52mm int
Stepped bush x 2
Bearing,6205
Clutch pulley & lining
Clutch plate
Circlip 30mm ext
Brake plate & lining
Circlip, 62mm int
Bearing 6206
Bearing holder
Belt guide
Complete assembly
Safety switch
V-belt, engine-spindle B59
Grease nipple
1
2
3
4
5
6
9
7
8
ILLUS.
PART No
DESCRIPTION
ILLUS.
PART No
DESCRIPTION
1
2
3
4
5
6
T303
T304
R323
R313
T302
T316
Starter cable 560mm (B&S)
Battery cable 460mm
Battery cable 330mm (Honda)
Battery Cable 230mm (B&S)
Solenoid (B&S)
Key switch
7
8
-9
T309
T305
T306
T311
Safety switch
Wire loom (B&S)
Wire loom (Honda)
Connecter, insulator
17
For use on DEUTSCHER TH910 Series II Ride-on mower with Honda GXV90K1 DAEU engines.
WARNING: Incorrect wiring may result in damage to the engines electrical system.
Only qualified and or competent electrical technicians should attempt
any repairs or alterations.
16
13
11
1
14
12
14
13
14
9
ILLUS.
PART No
DESCRIPTION
ILLUS.
DESCRIPTION
1
2
3
4
5
6
7
8
T309
T316
T309
T311
T306
T315
T304
R323
Safety switch, trans.
Key switch
Safety switch, cutters
Insulator, seat
Wiring loom
Battery 12 volt, 606
Cable, 460mm
Cable, 330mm
9
10
11
12
13
14
Starter motor
Stop switch
Engine
Earth, engine mount
Regulator / rectifier
Earth, reg/rectifier
18
For use on DEUTSCHER TH910 Series II Ride-on mower with Briggs & Stratton engine 28N707 series.
WARNING: Incorrect wiring may result in damage to the engines electrical system.
Only qualified and or competent electrical technicians should attempt
any repairs or alterations.
16
13
11
1
14
ILLUS.
PART No
DESCRIPTION
ILLUS.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
T309
T316
T309
T311
T305
T315
T304
R313
T303
T302
Safety switch, trans.
Key switch
Safety switch, cutters
Insulator, seat
Wiring loom
Battery 12 volt, 606
Cable, 460mm
Cable, 230mm
Cable, 560mm
Solenoid
11
12
13
14
15
16
Starter motor
Carby. solenoid
Stop switch
Engine
Charge wire
Engine mount, earth
19
WARRANTY POLICY:
MOWER
H. F. DEUTSCHER PTY. LTD. Will warrant the repair or replacement, free of charge, any parts of the mower that
are defective in materials or workmanship or both for a period of:
12 MONTHS FROM DATE OF PURCHASE.
• This does not cover normal wear abuse or incorrect service procedures as set out in the owner’s manual.
Parts such as blades, blade bolts, tyres and v-belts, which can be subjected, to use beyond their normal
intended working capacity are also excluded.
• This warranty is void if parts other than genuine have been used or if repairs or modifications have been
made without the manufacturer’s written authority.
• This warranty does not obligate the manufacturer’s agent or dealers to cover transport costs incurred in the
repair or replacement of any defective part.
The engine and transaxle on this mower are covered by separate manufacturer’s warranty
For your nearest Briggs & Stratton and Hydro-Gear dealer, Phone: 03 9796 4900
For your nearest Honda Power Equipment dealer, Phone: 03 9270 1111
All claims to be referred to ROVER MOWERS LIMITED
as warranty agents for the manufacturer.
NATIONAL CUSTOMER SERVICE
ROVER MOWERS LIMITED
155 FISON AVENUE WEST
EAGLE FARM, QLD. 4009
Phone: 07 3213 0233
Fax: 1800 806 659
www.rovermowers.com.au
FOR YOUR RECORD:
Model of Mower:………………………TH910………………………………………………………
Serial Number:………………………………………………………………………………………….
Date of Purchase………………………………………………………………………………………
Mower Purchased From ………………………………………………………………………………
……………………………………………………………………………………………………………
Remember: Proof of purchase is the responsibility of the owner and is necessary prior to warranty work
being under taken. An authorised dealer using genuine spare parts must carry out repairs or your warranty
will be void.
Manufactured in Australia by:
H.F. DEUTSCHER PTY LTD
711 Creswick Road, Ballarat 3350
Part No. T961
Edition: 2
24/09/06
TH910 Series II
Production start:
1640
January 2002
Serial number:1640
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
MODEL
TRANSAXLE SPEEDS
FLUID
QTY
SELF-PROPELLED
Z22
DEUTSCHER
1F
85W/140 .600ml
Y22
DEUTSCHER
2F
85W/140 .750ml
Y560
DEUTSCHER
2F
85W/140 .750ml
H26
DEUTSCHER
2F-1R
85W/140 .750ml
R280
DEUTSCHER
1F-1R
85W/140 .750ml
R360
DEUTSCHER
1F-1R
85W/140 .750ml
RIDER-MOWERS
TE910
EATON Variable
AWH68
1.8lt
TH910
HYDROGEAR Variable
20W/50
2.4lt
NOTE #
24/09/06
Quantity measurements are approximate and
should be checked by using the level indicators
provided on the individual transaxles.