Elation OPTI QA PAR User manual

user manual E L A TI ON | OPTI QA PAR™ | user manual
OPTI QA PAR™
www.elationlighting.com
©2014 ELATION PROFESSIONAL all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without notice.
ELATION PROFESSIONAL logo and identifying product names and numbers herein
are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes
all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this
document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-ELATION brands and product
names are trademarks or registered trademarks of their respective companies.
ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages, injuries to any
persons, and direct or indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a result of the improper,
unsafe, insufficient and negligent assembly, installation, rigging, and operation of
this product.
Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-3322 | 323-832-9142 fax | www.elationlighting.com | info@elationlighting.com
Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, Netherlands
+31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | info@elationlighting.eu
DOCUMENT
VERSION
Please check www.elationlighting.com for the latest revision/update of this manual.
Date
Document
Version
Software
Version
8/2014
2
≥1.5
DMX
Channel Modes
Notes
Added dimming curve modes and additional
1/3/5/6/8/9
Color Macros.
2
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
CONTENTS
General Information
4
Warranty
6
Safety Instructions
7
General Guidelines
8
Fixture Overview
9
Fixture Installation
10
Understanding DMX
12
Fixture Menu
16
Dimming Curves
18
DMX Channel Functions And Values
19
Cleaning and Maintenance
22
Technical Specifications
23
Optional Accessories
25
3
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
GENERAL INFORMATION
INTRODUCTION
Congratulations, you have just purchased one of the most innovative and
reliable lighting fixtures on the market today! The OPTI QA PAR™ has been
designed to perform reliably for years when the guidelines in this booklet are
followed. Please read and understand the instructions in this manual carefully
and thoroughly before attempting to operate this unit. These instructions contain
important information regarding safety during use and maintenance.
UNPACKING
Thank you for purchasing the OPTI QA PAR™ by Elation Professional®. Every OPTI
QA PAR™ has been thoroughly tested and has been shipped in perfect operating
condition. Carefully check the shipping carton for damage that may have
occurred during shipping. If the carton appears to be damaged, carefully
inspect your unit for
damage and be sure all accessories necessary to
operate the unit have arrived intact. In the event damage has been found or
parts are missing, please contact our customer support team for further
instructions. Please do not return this unit to your dealer without first contacting
customer support at the number listed below. Please do not discard the shipping
carton in the trash. Please recycle whenever possible.
BOX CONTENTS
•
(1) Gel Frame
•
(1) powerCON Cable
•
Manual & Warranty Card
4
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
CUSTOMER SUPPORT
Elation Professional® provides a customer support line, to provide set up help and
to answer any question should you encounter problems during your set up or
initial operation. You may also visit us on the web at www.elationlighting.com for
any comments or suggestions. For service related issue please contact Elation
Professional®.
ELATION SERVICE USA - Monday - Friday 8:00am to 5:00pm PST
Voice: 323-582-3322
Fax: 323-832-9142
E-mail: support@elationlighting.com
ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: +31 45 546 85 30
Fax: +31 45 546 85 96
E-mail: support@elationlighting.eu
WARRANTY REGISTRATION
The OPTI QA PAR™ carries a two-year (730 days) limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned service items
whether under warranty or not, must be freight pre-paid and accompany a
return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as
the R.A. number must also be written down on a piece of paper and included in
the shipping container. If the unit is under warranty, you must provide a copy of
your proof of purchase invoice. Items returned without a R.A. number clearly
marked on the outside of the package will be refused and returned at
customer’s expense. You may obtain a R.A. number by contacting customer
support at 323-582-3322.
IMPORTANT
NOTICE!
There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself; doing so will void your manufactures warranty. Damages resulting from
modifications to this fixture and/or the disregard of safety and general user
instructions found in this user manual void the manufactures warranty and are
not subject to any warranty claims and/or repairs.
5
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
2-YEAR LIMITED WARRANTY
A.
Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to
be free of manufacturing defects in material and workmanship for a period of two years, (730 days)
from the date of purchase. This warranty shall be valid only if the product is purchased within the
United States of America, including possessions and territories. It is the owner’s responsibility to
establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service, send the product only to the Elation Professional® factory. All shipping
charges must be pre-paid. If the requested repairs or service (including parts replacement) are within
the terms of this warranty, Elation Professional® will pay return shipping charges only to a designated
point within the United States. If the entire instrument is sent, it must be shipped in its original package.
No accessories should be shipped with the product. If any accessories are shipped with the product,
Elation Professional® shall have no liability what so ever for loss of or damage to any such accessories,
nor for the safe return thereof.
C.
This warranty is void if the serial number has been altered or removed; if the product is modified
in any manner which Elation Professional® concludes, after inspection, affects the reliability of the
product; if the product has been repaired or serviced by anyone other than the Elation Professional®
factory unless prior written authorization was issued to purchaser by Elation Professional®; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning or
periodic check-up. During the period specified above, Elation Professional® will replace defective
parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of
defects in material or workmanship.
The sole responsibility of Elation Professional® under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the
sole discretion of Elation Professional®. All products covered by this warranty were manufactured
after January 1, 1990, and bare identifying marks to that effect.
E.
Elation Professional® reserves the right to make changes in design and/or improvements upon its
products without any obligation to include these changes in any products theretofore
manufactured.
F.
No warranty, whether expressed or implied, is given or made with respect to any accessory
supplied with products described above. Except to the extent prohibited by applicable law, all
implied warranties made by Elation Professional® in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth above.
And no warranties, whether expressed or implied, including warranties of merchantability or fitness,
shall apply to this product after said period has expired. The consumer’s and or Dealer’s sole remedy
shall be such repair or replacement as is expressly provided above; and under no circumstances shall
Elation Professional® be liable for any loss or damage, direct or consequential, arising out of the use
of, or inability to use, this product.
G.
This warranty is the only written warranty applicable to Elation Professional® Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
6
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
SAFETY INSTRUCTIONS
The OPTI QA PAR™ is an extremely sophisticated piece of electronic
equipment. To guarantee a smooth operation, it is important to follow the
guidelines in this manual. The manufacturer of this device will not accept
responsibility for damages resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.
This device falls under PROTECTION CLASS 1. It’s essential this device be
grounded properly. Only qualified personnel should perform all electrical
connections.
•
For proper operation, follow the Installation guidelines described in this manual. Only qualified
and certified personnel should perform installation of this fixture and only the original rigging parts
(brackets) included with this fixture should be used for installation. Any modifications will void the
original manufactures warranty and increase the risk of damage and/or personal injury.
•
Never look directly into the light source of this fixture to prevent risk of injury to your retina, which
may induce blindness. Those suffering from EPILEPSY should avoid looking directly into the light
source of this unit at all times.
•
Always disconnect from main power source before performing any type of service and/or
cleaning procedure. Only handle the power cord by the plug end, never pull out the plug by
tugging the wire portion of the cord.
•
Do not operate this fixture if the power cord has become frayed, crimped and/or damaged. If
the power cord is damaged, replace it immediately with a new one of similar power rating.
7
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
GENERAL GUIDELINES
•
N E V E R
O P E N
T H I S
F I X T U R E
W H I L E
I N
U S E !
•
During the initial operation of this fixture, a light smoke or smell may emit from the
interior of the fixture. This is a normal process and is caused by excess paint in the
interior of the casing burning off from the heat associated with the lamp and will
decrease gradually over time.
•
This fixture is a professional lighting effect designed for INDOOR / DRY LOCATIONS
ONLY on stage, in nightclubs, theatres, etc.
•
Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while
operating, to prevent any fire hazard.
•
Minimum distance of inflammable materials from the surface 1.6 feet (0.5m).
•
DO NOT attempt installation and/or operation without knowledge how to do so.
•
DO NOT allow operation by persons who are not qualified to operate this type of
fixture. Most damages are the result of operations by nonprofessionals.
•
Consistent operational breaks may ensure the fixture will function properly for
many years to come.
•
DO NOT shake fixture, avoid brute force when installing and/or operating fixture.
•
Always install the fixture with an appropriate safety cable. When installing the
fixture in a suspended environment, always use mounting hardware that is no less
than M10 x 25 mm, also be sure the hardware is insert in the pre-arranged screw
holes in the bracket of the fixture.
•
Use the original packaging and materials to transport the fixture in for service.
•
DO NOT TOUCH the housing bare-hand during its operation. Turn OFF the power
and allow approximately 15 minutes for the fixture to cool down before replacing
or serving.
8
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
FIXTURE OVERVIEW
3
4
2
5
1
6
14
13
7
12
8
11
10
9
9
1.
FUSE
2.
3pin DMX OUT
3.
powerCON OUT
4.
powerCON IN
5.
3pin DMX IN
6.
Safety Cable Attachment Point
7.
Dual Yoke/Stand
8.
5pin DMX IN
9.
DOWN Button
10.
UP Button
11.
MODE Button
12.
LCD Menu Display
13.
Microphone
14.
5pin DMX OUT
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
FIXTURE INSTALLATION
T he el ec tri c c onnec ti on m ust onl y b e c arri ed out b y a qu al if i ed el ec tri c i an. CAUTIONS
•
For added protection, mount the fixture in areas outside walking paths, seating
areas, or in areas were unauthorized personnel might reach the fixture.
•
Max ambient operating temperature for this fixture is 113°F. (45°C)
Do not use the fixture under or above this temperature.
•
Before mounting the fixture to any surface, make sure the installation area can
hold a minimum point load of 10 times the weight of the fixture. 105 lbs / 48 kg)
•
Fixture installation must always be secured with a secondary safety attachment,
such as an appropriate safety cable.
•
Never stand directly below the device when mounting, removing or servicing.
POWER LINKING
Max number of units that can be power linked is 10 units @120V.
CLAMP MOUNTING
The OPTI QA PAR™ provides a unique integrated Dual Yoke / Floor Stand. When
mounting this fixture to truss be sure to secure an appropriately rated clamp using
an M10 screw fitted through the center hole of the Dual Yoke / Floor Stand.
SECURING
Regardless of the rigging option you choose for your OPTI QA PAR™ always be sure
to secure your fixture with a safety cable. The fixture provides a built-in rigging point
for a safety cable on the hanging bracket as illustrated above. Be sure to only use
the designated rigging point for the safety cable and never secure a safety cable to
a carrying handle.
10
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
MOUNTING POINTS
•
Overhead mounting requires extensive experience, including amongst others
calculating working load limits, installation material being used, and periodic
safety inspection of all installation material and the device. If you lack these
qualifications, do not attempt the installation yourself. Improper installation can
result in bodily injury.
•
Fixture is fully operational in the specific mounting positions as illustrated below.
SAFETY
CABLE
Always use a Safety Cable whenever installing this fixture in a suspended
environment to ensure the fixture will not drop if the clamp fails.
11
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
UNDERSTANDING DMX
DMX-512
DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and
controller manufactures as a form of communication between intelligent fixtures
and controllers. DMX allows all makes and models of different manufactures to be
linked together and operate from a single controller. This is possible as long as all the
fixtures and the controller are DMX compliant. A DMX controller sends the DMX data
instructions to the fixture allowing the user to control the different aspects of an
intelligent light. DMX data is sent out as serial data that travels from fixture to fixture
via data “IN” and data “OUT” XLR terminals located on the fixtures (most controllers
will only have output jacks).
DMX LINKING
To ensure proper DMX data transmission, always use proper DMX cables and a
terminator. When using several DMX fixtures try to use the shortest cable path
possible. Never split a DMX line with a “Y” style connector. The order in which the
fixtures are connected in a DMX line does not influence the DMX addressing. For
example; a fixture assigned a starting DMX address of 1 may be placed anywhere in
the DMX chain, at the beginning, at the end, or anywhere in the middle. The DMX
controller knows to send data assigned to address 1 to that fixture no matter where
it is located in the DMX chain. The OPTI QA PAR™ can be controlled via DMX-512
protocol and the DMX address is set via the control menu.
DATA CABLE (DMX Cable) REQUIREMENTS (For DMX and Master/Slave Operation)
Your fixture and your DMX controller require a standard 3pin or 5pin XLR connector
for data input and data output (see figure below). If you are making your own
cables, be sure to use two conductor, shielded digital DMX cable rated at 120 ohms;
this cable is designed for DMX transmission and may be purchased from your Elation
dealer or at most professional lighting retailers. Your cables should be made with a
male and female XLR connector on either end of the cable. Also, remember that a
DMX line must be daisy chained and cannot be split, unless using an approved DMX
splitter such as Elation’s Opto Branch 4™, Opto Branch 8™, or DMX-Branch/4™.
12
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
Be sure to follow the above figure when making your own cables. Do
not use the ground lug on the XLR connector. Do not connect the
cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX-512 CONTROLLER CONNECTION
Connect the provided XLR cable to the female XLR output of your controller and the
other side to the male XLR input of the OPTI QA PAR™ The diagram below illustrates
a typical DMX-512 connection when the fixture is in the 9 Channel Mode. You can
chain multiple panels together through serial linking. The cable that should be used
is two conductor, shielded DMX cable with XLR input and output connectors. Always
be sure daisy chain your in and out data connections, never split or “Y” your DMX
connections unless you are using an approved DMX splitter such as Elation’s Opto
Branch 4™, Opto Branch 8™, or DMX-Branch/4™.
Address 1
Address 10
Address 19
DMX
CONTROLLER
13
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
DMX-512 CONNECTION WITH DMX TERMINATOR
A DMX terminator should be used in all DMX lines especially in longer runs. The use of
a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm
1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector
(DATA + and DATA -). This fixture is inserted in the female XLR connector of the last
fixture in your daisy chain to terminate the line. Using a line terminator will decrease
the possibilities of erratic behavior.
5pin XLR DMX CONNECTORS
Some manufactures use 5pin XLR connectors for DATA transmission in place of 3pin.
5pin XLR fixtures may be implemented in a 3pin XLR DMX line. When inserting
standard 5pin XLR connectors in to a 3pin line a cable adaptor must be used, these
adaptors are readily available at most electric stores. The following chart details a
proper cable conversion.
14
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
DMX ADDRESSING
All fixtures should be given a DMX starting address when using a DMX controller, so
the correct fixture responds to the correct control signal. This digital starting address
is the channel number from which the fixture starts to “listen” to the digital control
information sent out from the DMX controller. The allocation of this starting DMX
address is achieved by setting the correct DMX address on the digital display
located on the back of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set
different address for each individual fixture. Be advised that setting all fixtures to the
same DMX address will subsequently control all fixtures in the same fashion, in other
words, changing the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the
channel number you have set, based on the quantity of control channels (DMX
channels) of each fixture. That means changing the settings of one channel will only
affect the selected fixture.
In the case of the OPTI QA PAR™, when in the 9 Channel you should set the starting
DMX address of the first unit to 1, the second unit to 10 (1 + 9), the third unit to 19 (10
+ 9), and so on.
Note: During start-up the OPTI QA PAR™ will automatically detect whether a DMX
data signal is being received or not. If DMX data signal is being received, the display
will show "Addr=XXX" (XXX representing the actual DMX address). If the fixture is not
receiving a DMX signal the display will flash. If your fixture is connected to a DMX
controller and the display is flashing (not receiving a DMX signal), please check the
following:
-
The 3pin or 5pin XLR input plug (cable with DMX signal from controller) is not
connected or is not inserted completely into the DMX input jack of the fixture.
-
The DMX controller is switched off or defective.
-
The DMX cable or connector is defective.
-
A DMX terminator has been inserted into the last fixture in your DMX chain.
15
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
FIXTURE MENU
ON-BOARD SYSTEM MENU
The OPTI QA PAR™ comes with an easy to navigate system menu.
sections will cover how to access each menu function.
The next
LCD CONTROL PANEL DISPLAY
The (3) button control panel (see image below) located on back of the fixture
allows you to access the main menu and make all necessary adjustments to the
OPTI QA PAR™.
During normal operation, pressing the MODE button will navigate through the
different function menus. Once you reach a desired menu, the variable field can be
adjusted within the selected menu by using the UP or DOWN buttons, until the
desired value is displayed. For example, the RampMode menu variable field can be
set to 0, 1, 2, 3, or 4. Press the UP or DOWN buttons to select the desired value and
confirm your selection by pressing the MODE button. Exit at any time without making
any adjustments by pressing the MODE button.
INFORMATION DISPLAYED DURING INITIAL POWER ON
When the fixture is initially powered ON, the display shows the following information:
Elation
V1.5
Fixture Software Version
16
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
ELATION© OPTI QA PAR™
S Y S T E M M E N U - VERSION 2
MENU
Specifications are subject to change without any prior written notice.
OPTIONS / VALUES
DESCRIPTION
ON
LCD Display Backlight Always ON
OFF
LCD Display Backlight OFF/LOCKED after 30 seconds.
To UNLOCK Display, press any button for 10 seconds.
Curve = (0) Standard, (1) Stage, (2) TV,
(3) Architectural, (4) Theatre
Set Dimming Curve
1-CH, 3-CH, 5-CH, 6-CH, 8-CH, 9-CH
DMX Channel Mode
001 ~ 512
DMX Address Setting
ColMacro
Macro = 0 ~ 64
Set Color Macro
ColMacro
Sound
Sound Active Mode to change Color Macros
Progr = All, 1 ~9
Set Internal Program
Speed = 1 ~ 16, Sound
Set Internal Program Chase Speed
ColSet
Red = 0 ~ 255
Set Red LED value manually
ColSet
Blue = 0 ~ 255
Set Blue LED value manually
ColSet
Green = 0 ~ 255
Set Green LED value manually
ColSet
Amber = 0 ~ 255
Set Amber LED value manually
DispPerm
RampMode
DMX
ColProgr
ColSpeed
17
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
DIMMING CURVES
The RampMode menu allows you to select one of the following preset dimming
curves: (0) Standard, (1) Stage, (2) TV, (3) Architectural, or (4) Theatre.
(See diagram below for more details)
18
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
DMX CHANNEL FUNCTIONS AND VALUES
ELATION© OPTI QA PAR™
DMX Channel Values / Functions VERSION 2 (9 DMX Channels)
Specifications are subject to change without any prior written notice.
MODE / CHANNEL
1 CH
3 CH
5 CH
6 CH
VALUE
8 CH
FUNCTION
9CH
RED*
1
1
1
*RED Control Disabled when fixture is in 8 or 9 CH Mode
and CH 5 Color Macros are being used.
1
0-255
2
2
2
RED (0-100%)
GREEN*
*GREEN Control Disabled when fixture is in 8 or 9 CH Mode
and CH 5 Color Macros are being used.
2
0-255
3
3
3
GREEN (0-100%)
BLUE*
*BLUE Control Disabled when fixture is in 8 or 9 CH Mode
and CH 5 Color Macros are being used.
3
0-256
4
4
4
BLUE (0-100%)
AMBER*
*AMBER Control Disabled when fixture is in 8 or 9 CH Mode
and CH 5 Color Macros are being used.
4
0-255
AMBER (0-100%)
COLOR MACROS
0
1
1
5
5
OFF
1-4
COLOR MACRO 1
5-8
COLOR MACRO 2
9-12
COLOR MACRO 3
13-16
COLOR MACRO 4
17-20
COLOR MACRO 5
21-24
COLOR MACRO 6
25-28
COLOR MACRO 7
29-32
COLOR MACRO 8
33-36
COLOR MACRO 9
37-40
COLOR MACRO 10
41-44
COLOR MACRO 11
45-48
COLOR MACRO 12
49-52
COLOR MACRO 13
53-56
COLOR MACRO 14
57-60
COLOR MACRO 15
61-64
COLOR MACRO 16
65-68
COLOR MACRO 17
69-72
COLOR MACRO 18
73-76
COLOR MACRO 19
77-80
COLOR MACRO 20
81-84
COLOR MACRO 21
85-88
COLOR MACRO 22
89-92
COLOR MACRO 23
93-96
COLOR MACRO 24
97-100
COLOR MACRO 25
19
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
ELATION© OPTI QA PAR™
DMX Channel Values / Functions VERSION 2 (9 DMX Channels)
Specifications are subject to change without any prior written notice.
MODE / CHANNEL
1 CH
3 CH
5 CH
6 CH
VALUE
8 CH
FUNCTION
9CH
20
101-104
COLOR MACRO 26
105-108
COLOR MACRO 27
109-112
COLOR MACRO 28
113-116
COLOR MACRO 29
117-120
COLOR MACRO 30
121-124
COLOR MACRO 31
125-128
COLOR MACRO 32
129-132
COLOR MACRO 33
133-136
COLOR MACRO 34
137-140
COLOR MACRO 35
141-144
COLOR MACRO 36
145-148
COLOR MACRO 37
149-152
COLOR MACRO 38
153-156
COLOR MACRO 39
157-160
COLOR MACRO 40
161-164
COLOR MACRO 41
165-168
COLOR MACRO 42
169-172
COLOR MACRO 43
173-176
COLOR MACRO 44
177-180
COLOR MACRO 45
181-184
COLOR MACRO 46
185-188
COLOR MACRO 47
189-192
COLOR MACRO 48
193-196
COLOR MACRO 49
197-200
COLOR MACRO 50
201-204
COLOR MACRO 51
205-208
COLOR MACRO 52
209-212
COLOR MACRO 53
213-216
COLOR MACRO 54
217-220
COLOR MACRO 55
221-224
COLOR MACRO 56
225-228
COLOR MACRO 57
229-232
COLOR MACRO 58
233-236
COLOR MACRO 59
237-240
COLOR MACRO 60
241-244
COLOR MACRO 61
245-248
COLOR MACRO 62
249-252
COLOR MACRO 63
253-255
COLOR MACRO 64
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
ELATION© OPTI QA PAR™
DMX Channel Values / Functions VERSION 2 (9 DMX Channels)
Specifications are subject to change without any prior written notice.
MODE / CHANNEL
1 CH
3 CH
5 CH
6 CH
VALUE
8 CH
FUNCTION
9CH
STROBE / SPEED*
6
6
*SPEED Control ONLY available when fixture is in 9 CH Mode
and CH 7 DMX Value is (128-223)
0-15
NO STROBE / OFF
16-255
STROBE Effect SLOW to FAST
0-255
*SPEED Control SLOW to FAST
MODE
0-127
7
2
5
7
8
NO Function
128-159
Automatic COLOR Mixing
160-191
3 COLOR Change
192-223
7 COLOR Change
224-255
64 COLOR MACRO SOUND Active
DIMMER INTENSITY
0-255
Intensity 0 to 100%
DIMMING CURVE MODES
3
5
6
8
9
0-20
STANDARD
21-40
STAGE
41-60
TV
61-80
ARCHITECTURAL
81-100
THEATER
101-255
Default to Unit Setting
21
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
CLEANING AND MAINTENANCE
CLEANING
Frequent cleaning is recommended to insure proper function, optimized light output,
and an extended life. The frequency of cleaning depends on the environment in
which the fixture operates: damp, smoky or particularly dirty environments can
cause greater accumulation of dirt on the fixture’s optics.
•
Clean the external lens surface at least every 20 days with a soft cloth to avoid
dirt/debris accumulation. Never use alcohol, solvents, or ammonia based
cleaners.
MAINTENANCE
Regular inspections are recommended to insure proper function and extended life.
There are no user serviceable parts inside this fixture, please refer all other service
issues to an authorized Elation service technician. Should you need any spare parts,
please order genuine parts from your local Elation dealer.
Please refer to the following points during routine inspections:
•
A detailed electric check by an approved electrical engineer every 3 months, to
make sure the circuit contacts are in good condition and prevent overheating.
•
Be sure all screws and fasteners are securely tightened at all times. Lose screws
may fall out during normal operation resulting in damage or injury.
•
Check for any deformations on the housing, color lenses, rigging hardware and
rigging points (ceiling, suspension, trussing). Deformations in the housing could
allow for dust to enter into the fixture. Damaged rigging points or unsecured
rigging could cause the fixture to fall and seriously injure a person(s).
•
Inspect all moving parts and make sure there are no signs of wear and
rotate/move without imbalances.
•
Electric power supply cables must not show any damage, material fatigue or
sediments. Never remove the ground prong from the power cable.
22
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
TECHNICAL SPECIFICATIONS
FEATURES
10° Beam Angle
Smooth and Variable Curve Dimming Control
Gel Frame Included
Flicker Free Operation for TV and FILM
SOURCE
18 x 5W QUAD Color (RGBA) LEDs
50,000 Hour Average Life
PHOTOMETRIC DATA
2065 LUX (192 FC) @9.8 ft. (3m) 10° Full ON
EFFECTS
Multiple Color Macros
Variable Color and Strobe Macros
Variable Electronic Dimming Curves
COLOR
RGBA (Red, Green, Blue, Amber)
CONTROL / CONNECTIONS
6 DMX Channel Modes (1 / 3 / 5 / 6 / 8 / 9)
3pin & 5pin DMX In/Out
3 Button Control Panel
LCD Menu Display
powerCON Power In/Out
Power Link Up To (10) Units at 120V
SIZE / WEIGHT
Length: 10.9” (278mm)
Width: 8.7” (221mm)
Vertical Height: 14.1” (358mm)
Weight: 10.6 lbs. (4.8kg)
ELECTRICAL
AC 100-240V - 47/63Hz
135W Max Power Consumption
APPROVALS / RATINGS
CE Approved
cETLus Approved
IP20 Rated
INSTALLATION
Rigging: Dual Yoke / Floor Stand
Working Position: Any (360°)
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
23
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
PHOTOMETRIC DATA
DIMENSIONAL DRAWINGS
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
24
OPTI QA PAR™ User Manual ver 2
www.elationlighting.com
OPTIONAL ACCESSORIES
ORDER CODE
ITEM
TRIGGER CLAMP
Heavy Duty Wrap Around Hook Style Clamp
BD-03
Barn Door
LSF536
Light Shaping Filter 30° 20” x 24” Sheet
LSF537
Light Shaping Filter 20° 20” x 22” Sheet
LSF538
Light Shaping Filter 60° x 1° 20” x 24” Sheet
LSF559
Light Shaping Filter 10° 20” x 24” Sheet
EWDMXSYSTEM
Wireless DMX System (1 Transmitter, 1 Receiver)
EWDMXT
Wireless DMX Transmitter
EWDMXR
Wireless DMX Receiver
PLC3
3’ (1m) PowerCON PRO Link Cable
PLC6
6’ (1.8m) PowerCON PRO Link Cable
AC3PDMX5PRO
5 ft. (1.5m) 3pin PRO DMX Cable
AC5PDMX5PRO
5 ft. (1.5m) 5pin PRO DMX Cable
Additional Cable Lengths Available
25
OPTI QA PAR™ User Manual ver 2