BMW R1100/1150 General Turbo Instructions rbracing

BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Electrical Data for the R1100RT
1
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
R1100RT
Relay #6 is the fuel pump relay. For safety reasons it is tied into the engine kill switch
which makes it a good place to pick up +12VDc. Lifting the fuse allows you access to to
the Green/Yellow stripe wire. This is where we pick up +12VDc for the following parts of
the RB Racing Turbo System:
1. RSR 400i Injector Controller: Red wire.
2. Oil scavenge pump: Red wire.
3. On/Off RSR Water Injection Arm/Disarm Switch: Red wire
4. To Inverter 30A relay to turn on Inverter. Red wire.
Fuse #1 is the Instrument Cluster Fuse. This is where we pick up +12VDc for the
following parts of your RB Racing Turbo System:
1. RSR Air Fuel Ratio Gauge: Red Wire and Orange Wire joined here.
2. RSR Orca Turbo Dash: Red Wire.
Water Injection Power Supply (Inverter): Battery + to 20A fuse to relay. OEM Relay
#6 triggers direct 12V to Inverter.
R1100S (See diagram on page 3)
Relay #4 is the fuel pump relay. For safety reasons it is tied into the engine kill switch
which makes it a good place to pick up +12VDc. Lifting the fuse allows you access to to
the Green/Yellow stripe wire. This is where we pick up +12VDc for the following parts of
the RB Racing Turbo System:
1. RSR 400i Injector Controller: Red wire.
2. Oil scavenge pump: Red wire.
3. On/Off RSR Water Injection Arm/Disarm Switch: Red wire
4. To Inverter 30A relay to turn on Inverter. Red wire.
Fuse #3 is the Instrument Cluster Fuse. This is where we pick up +12VDc for the
following parts of your RB Racing Turbo System:
1. RSR Air Fuel Ratio Gauge: Red Wire and Orange Wire joined here.
2. RSR Orca Turbo Dash: Red Wire.
Water Injection Power Supply (Inverter): Battery + to 20A fuse to relay. OEM Relay
#4 triggers direct 12V to Inverter.
2
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Electrical data for R1100S
3
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Pneumatic Diagram All R1100/1150 Models
Note: No clamps are used on the pneumatic lines save to the two used on the right and
left throttle body vacuum ports located on the bottom of each throttle body.
4
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Water Injection Schematic
5
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Assembly Sequence and Photos
Stripped down and ready to install. The air box air temperature sensor will just be tied
off to sense ambient temperatures.
We provide a 3/8” hose that sockets into the original air box breather aluminum fitting.
Run this hose to the rear of the bike by the license plate and water injection reservoir.
Use plastic tie wraps to secure the hose to the frame.
The aluminum bracket that is bolted to the top center of the frame will have to have the
vertical tabs cut off (See pages 18 and 19). The connector tube from the turbo to the
intercooler will pass this area.
The Bosch Billet Fuel Regulator mounts as shown with a supplied stainless steel
bracket.
6
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
The turbo exhaust header is a four piece design with three slip joints. Two exhaust port
bends, one Y pipe / collector and a slip connector to the turbo. You may coat the inside
of each slip joint with Permatex 598B (Black) non-hardening gasket compound.
Use the stock oem stainless metal gaskets.
Two Bolt Exhaust: Use the four stock oem 8mm x 1.25 hex nuts
Three Bolt Exhaust (Early R1100): Use the six 8mm x 1.25 nuts provided.
Note: In that the front header is a “Y” shape with two slip joints and since the two bolt
flanges do not rotate, once on the studs, the whole assembly has to go on in one shot.
The slip joints must be fully seated. Using Permatex 598B will allow the joints to be
rotated a bit during the assembly and not bind. Use a rubber hammer and gently tap
things together. The merge collector, in its final position, should be less than 1/16” away
from the lower engine casting.
7
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Billet RB Racing BoostMaster Wastegate. Note that the top and side fitting point to the
left side of the bike (as you sit on it).
An annealed copper gasket is provided. You may place a light coating of Permatex
598B on the gasket faces.
Four stainless steel 5/16” x 18 x 1 1/4” socket heat stainless cap screws, lock washers
and nuts are provided. On the left side the bolts install from the top and on the right side
they install from the bottom.
8
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Chrome wastegate exhaust exits to the left. Two 5/16 x 18 x 3/4” Stainless Button Head
Cap screws hold the tube to the wastegate. Tighten with 3/16” Allen and 1/2” wrench.
The chrome tube vents the exhaust gases when the wastegate opens.
The wastegate is shipped with a basic spring pressure of around 8-9 psi. The pneumatic
boost controller allows you to turn up the boost to 25 psi. The two stage water injection
is set to activate at 4 and 8 psi. On pump gas and without lower compression forged
pistons we recommend the boost be held to 9 psi.
12-15 psi more than doubles the horsepower. Higher octane or heavy doses of Toluene.
9
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Left side turbo connector pipe with slip joint. Coat inside of slip with Permatex 598B. It is
a slip joint and no form of clamp should be used.
10
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Here the connector pipe snakes under the bike. Make sure the connector pipe does not
touch or interfere with anything on the side of the bike as it goes along the side of the
engine casting.
11
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
The O2 sensor sockets back into the new location on the left side. Twist the wires 3
turns CCW, then screw the sensor into the new location.
12
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Double ceramic ball bearing turbocharger. The exhaust housing has been coated in
silver ceramic. The AN4 oil feed line must be tightened down securely otherwise and
CCW twisting motion on the stainless feed line will loosen the fitting. Use 9/16” wrench
to tighten.
Four 5/16” x 18 x 1.5” Hex bolts with washers, lock washers and hex nuts hold turbo to
connector tube. Sequence is bolt, washer and then lock washer and nut on reverse
side. Bottom bolts inserted front to rear. Top left rear to front. Top right front to rear.
Five 8mm x 1.25 x 1 25mm stainless steel socket head cap screws and lock washers.
You must install the turbo exit pipe (page 14) before you install the turbo.
13
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Turbo Exit Pipe
The ceramic coated turbo exit pipe bolts to the inside of the rear pivot stay arm.
Remove the 10mm x 1.5 nut on the inside of the stay arm and use a 10mm Allen
wrench to tighten the bolt to the turbo exit tube.
The turbo end up being supported by this bolt, the connector tube and the tail section. It
is a rock solid mount system.
Use the five 8mm x 1.25 x 25mm stainless socket head cap screws and lock washers
on the exit flange. No gasket is used on the exit. Coat the exit turbo housing with 598B
Permatex. The four 5/16” x 18 x 1.5” bolts are used for the turbo connector pipe. See
page 13 for bolt insertion directions. 6mm Allen wrench and 1/2” wrenches.
An annealed four bolt copper gasket provided is used between the turbo connector pipe
and the turbo. You may place a light coating of 598B Permatex on the gasket faces.
14
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Turbo Exit Pipe
The Black Hole muffler section will slip onto the turbo exit pipe. You may place a coating
of Permatex 598B inside the slip joint of the muffler.
A spring is provided to pull the slip jointed section together.
15
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
With the turbo bolted in place the oil feed line will snake in a loop back to the right side
of the bike and will pass over the 10mm mounting bolt location on the turbo exit flange.
16
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Here the stainless steel AN4 oil feed line passes over the 10mm mounting bolt location
This is the turbo to intercooler ceramic coated connector pipe. Note the O-Ring in the
three bolt mounting flange and the two rubber bumpers on the tube. The two rubber
bumpers will press against the base of the intercooler.
17
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
The connector tube will snake down from the top, rotating into position where the three
bolt flange will mate up with the turbo.
Before you insert the connector tube you must trim the two vertical tabs mentioned on
page 3 of the instructions. A clear photo of the modified bracket can be seen on page
19.
18
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Three 6mm x 1.0 x 25 mm stainless socket head cap screws with lock washers secures
the three bolt flange to the turbo. Be sure the O-Ring is in place.
Twirl the three bolts in with your fingers and use a ball head 5mm Allen to tighten.
19
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
An silicone hose coupler attached the connector tube to the intercooler. Two #36
stainless hose clamps are provided. Do not install any intercooler hose clamps until all
silicone connector hoses are in place and everything is properly aligned.
It is general, it is good practice to get everything into place and they slowing tighten up
the entire system.
20
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Slipping the Black Hole Muffler into place and installing the retention spring provided.
The Muffler sockets into the left rear dowel under the tail section. An integral rubber
sleeve is in the muffler bracket.
21
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
The license plate bracket sockets into the right underside dowel and rests on top of the
ceramic coated Black Hole muffler bracket.
A 5/16” x 18 x 1” bolt, washer, lock washer and nut are provided. Tighten with 1/2”
wrenches. Be sure the two parts i.e. the muffler and the license plate bracket are seated
equally depth-wise on their respective dowels.
Note the breather tube hose to the right.
The Bracket incorporates a L.E.D. light.
The water injection reservoir will actually bolt to this bracket and the license plate will
bolt to the face of the reservoir.
22
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
The intercooler is inserted from the top.
23
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
The air cleaner assembly sockets to the turbo compressor housing. Note that these is
an internal O-Ring seal. We suggest you coat the inside of the slip area and the O-Ring
with a light grease as it is a tight seal.
A 6mm stainless steel and lock washer secures the assembly to the turbo. Note the
spacer which goes between the air cleaner and the turbo..
24
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Here the K&N air cleaner assembly is mounted and secured with the 6mm mounting
bolt and spacer.
You must push the air cleaner fully seated as show. The mount is designed to fully
secure the air cleaner from falling off or becoming dislodged.
Note the air cleaner rubber mount is canted. Rotate the air clear so it cants inward and
straight “back” but not so as to touch the tail pipe.
25
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Three silicone hoses are provide with appropriate hose clamps, two hoses to the right
side and one on the left side.
26
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
Right side silicone hose couplers.
Note the orange Adel clamp on the frame. This will be used to secure the 1/4” return line
from the Bosch Billet fuel regulator
27
BMW R1100/1150 General Turbo Instructions rbracing-rsr.com
This is the vacuum line from the right to left throttle bodies and the tee that branches to
the Bosch Billet fuel regulator.
In the pneumatic diagram on page 4 two additional tees will be placed within this
system. No clamps are used on the brass tees but two clamps are used, one for each of
the throttle bodies. Use 7mm nut driver to tighten the clamps.
Oil System
A separate PDF is provided with each RB Racing R series turbo kit.
Fuel Lines
A separate PDF is provided with each RB Racing R series turbo kit.
Orca Turbo Dash
A separate PDF is provided with each RB Racing R series turbo kit.
RB Racing Air Fuel Ratio Gauge and RSR AIC400
A separate PDF is provided with each RB Racing R series turbo kit.
Water Injection System
A separate PDF is provided with each RB Racing R series turbo kit.
28