INTERACT3.
User manual
Wireless adaptor plug switch IP 20/IP 44, wireless adaptor plug dimmer
German/English
53916.00.001.01 Wireless adaptor plug switch IP 20 (Model ZW ZS 3500)
53917.00.001.01 Wireless adaptor plug switch IP 44 (Model ZW ZSA 3500)
53918.00.001.01 Wireless adaptor plug dimmer (Model Z-DAN 300)
1
INTERACT3.
INTERACT3.
Dear INTERACT3 user:
Index of contents/overview of chapters
You can download this user manual in an appropriately larger
format from our internet website www.popp.eu.
1.
2.
2.1
3.
4.
5.
5.1
5.2
5.3
5.4
5.5
5.6
Our service hotline is available for further product-relevant
questions at the service line: +49 (0) 92 73/73-150.
6.
7.
2
General information on “Z-Wave” .........................................6
General information ..................................................................9
LED indication .............................................................................9
Before installation/startup .......................................................9
General Information on wireless plug adaptors ............10
Functions/operation ............................................................... 13
Network inclusion ................................................................... 13
Operation ................................................................................. 14
Special function wireless plug adaptor dimmer .............. 15
Special function Child Protection ....................................... 15
Reset............................................................................................. 16
Including a wireless plug adaptor
into third-party networks ....................................................... 18
Technical Data ......................................................................... 19
Guarantee ................................................................................20
3
INTERACT3.
1. GENERAL INFORMATION ON “Z-WAVE”:
INTERACT³ is a radio system that is based on Z-WAVE
technology. INTERACT³ off ers a varied range of advantages in comparison to other radio systems:
Safe:
Generally, radio systems build a direct link between the transmitter and the receiver. The radio signal is attenuated by every
obstacle along its path (in the household e.g. wall, furniture
etc.), in the worst case the radio system ceases to function. The
advantage of the intelligent INTERACT³ system is the so-called
routing function: All devices of INTERACT³ not only act as the
transmitter or the receiver but also simultaneously as the “repeater”. Should a direct radio link between the transmitter and
the receiver not be possible, communication will be established
with the assistance of other devices.
4
INTERACT3.
Communicative:
INTERACT³ is a bidirectional radio system. This means that a
signal is not just sent but also a feedback confirming the reception of the signal occurs automatically. The safety of transmission
of the INTERACT³ radio bus technology is comparable with that
of a wire-linked bus system. It is likewise possible to determine
the switching status by pushing a button: Has the cellar light been
definitely switched off?
Trouble-free:
INTERACT³ transmits at a regulated frequency band with a frequency of 868 MHz. Every INTERACT³ network has its own
unique network identification. Therefore, it is possible to operate
two or more independently-operating networks in a room or home
without any interferences. Troubles that can be caused by other
devices, as is the case in open, non-regulated frequencies
(e.g. 433 MHz) are excluded.
5
INTERACT3.
6
INTERACT3.
Established:
Although the Z-Wave technology is new, it has already developed to form a technical standard. Renowned manufacturers from
various fields offer solutions and applications that are based on
Z-Wave technology and compatible among one another. This
makes the system fit for the future and promises further upgrade
phases. Further information can be found on www.z-wave.
com.
2. GENERAL INORMATION:
Dynamic:
INTERACT³ is equipped with a dynamic network structure. Right
from the start, the position of the individual INTERACT³ devices
who are supplied with 230 Volts is monitored and automatically
updated in the case of changes. As a means of which it is possible to continuously adapt the network to its individual requirements, wholly automatically without the necessity of any programming tasks.
2.1 LED indication:
Yellow:
device is switched on.
Blue:
device is switched off.
Red:
device defective/
Configuration not successful.
Blinking yellow:
device is dimming up.
Blinking blue:
device is dimming down.
Green:
Configuration successful.
Red/Green blinking:
device is not programmed.
Red/yellow/green:
Reset is accomplished.
Short green light:
Child protection is deactivated.
Blinking red:
Child protection is activated.
Thermoswitch is activated
7
INTERACT3.
3. BEFORE INSTALLATION/STARTUP:
Please carefully read the enclosed user manual before installation in order to ensure an error-free functioning.
ATTENTION: Works with 230 voltage networks may be
done only by authorized technicians under consideration
of the country-specific installation guidelines/ norms. Prior
to the assembly of the product, the voltage network has to
be switched on and ensured against re-switching.
INTERACT3.
If a danger-free operation of the equipment cannot be assured,
the voltage supply has to be immediately interrupted and the
equipment has to be protected from unintended operation.
NOTE: The product is dispatched in the delivery state “not programmed”. While installation or actuating the pushbutton, this
status is showed by a blinking red/ green LED.
The product is permitted only for proper use as specified in the
user manual. Any kind of guarantee claim has to be forfeited if
changes, modifications or painting are undertaken. The product
must be checked for damages immediately after unpacking. In
the case of a damage, the product should not be operated in
any case.
8
9
INTERACT3.
INTERACT3.
4. GENERAL INFORMATION ON WIRELESS PLUG ADAPTORS:
•
Wireless adaptor plug switch IP 20 (761 293) (Model ZW ZS 3500)
Wireless adaptor plug switch IP 44 (761 309) (Model ZW ZSA 3500)
Wireless adaptor plug dimmer (761 316) (Model ZW ZDAN 300)
•
Flip-open cover
•
Serves the purpose of switching or dimming of fi tted lights
either via radio communication or directly over the
“FUNCTION” button of the wireless plug adaptor.
Wireless plug adaptors IP 20 (761 293) and IP 44 (761
309) are suitable for the wireless switching of incandescent
bulbs, HV and NV-halogen bulbs (all transformer types).
Wireless dimmer adaptor (761 316) is suitable for the
wireless dimming of HV and NV-halogen bulbs (all transformer types).
Attention: Applies only for iron-core transformers, see label!
Function
button
Function
button
Status
LED
Status
LED
10
NOTE: Do not interconnect more than one plug
adaptor!!
11
INTERACT3.
NOTE:
• Insert wireless adaptor plugs only in sockets with safety
contact/ ground wire.
• Use of the wireless adaptor plug with devices that cannot
comply with the technical standards can cause malfunctioning or damage connected equipments or wireless
adaptor plugs.
• Since the wireless adaptor plug deals with electronic equipment, one has to take special care in contact with moisture
or cleaning agents. We recommend cleaning only with a
dry cloth.
12
INTERACT3.
5. FUNCTIONS/ OPERATION:
5.1 NETWORK INCLUSION:
For the adaptation of the wireless adaptor plug switch/dimmer,
you need a controller (remote control or wireless wall-switch).
...then...
...press 3 times
in each case
Press the “UP” or “DOWN” button on the desired group/scene
of the remote control or the wireless wall-switch three times (blinks
green) and then three times on the device to be included: The
device is automatically associated with the selected group/
scene or wall-mounted switch.
13
INTERACT3.
NOTE: If a radio link should not be possible while network
inclusion, please bring the controller close to the wireless
adaptor plug.
NOTE: For the purpose of adaptation, both the controller
as well the wireless adaptor plug have to be supplied with
power.
INTERACT3.
5.3 SPECIAL FUNCTIONS OF THE WIRELESS ADAPTOR
PLUG DIMMER:
The wireless adaptor plug dimmer saves the most recently-set
light intensity and automatically switches back to the same level
of brightness at which it was switched off.
5.4 SPECIAL FUNCTIONS – CHILD PROTECTION:
5.2 OPERATION
The wireless adaptor plug can be operated either over a controller (remote control or wireless wall-switch) or directly by actuating
the “FUNCTION” button on the device. By a brief pushing, it is
switched ON/ OFF. In the case of the dimmer, there is also the
possibility of dimming (UP/ DOWN) by prolonged pressing of
the “FUNCTION” button.
14
If the radio adaptor plug is present in the “child protection mode”
(also see the user manual wireless wall-switch or remote control),
this can be disabled by pressing the “FUNCTION” button thrice
within a span of 1.5 seconds. After 5 seconds of inactivity, the
tamper-proof “child protection mode” is automatically reactivated.
15
INTERACT3.
INTERACT3.
KINDLY NOTE: The description for activation or deactivation of
the child protection function is described in the user manual of
the remote control/wireless wall-switch!
5.5 RESET:
Sometimes it might be necessary to reset the wireless adaptor
plug to the factory settings and delete all the programming steps
or associations. For resetting, a controller (remote control or
wireless wall-switch) is needed.
...then...
... press “UP” or
“DOWN” thrice
“EXCL.”
Press the “EXCL.” button on the remote control for 2 seconds
(the LED blinks green) and then press the “FUNCTION” button
thrice within a span of 1.5 seconds.
The successful reset operation is signaled by a green light
(3 seconds), whereas a failure by red light (3 seconds).
NOTE: A successful reset of the wireless adaptor plug means
that it has once again assumed the factory settings.
16
17
INTERACT3.
INTERACT3.
5.6 INCLUDING A WIRELESS ADAPTOR PLUG INTO A
THIRD-PARTY NETWORK:
6. TECHNICAL DATA:
Wireless adaptor plug switch IP 20 (Model ZW ZS 3500)
controller
third party
manufacturer
...then...
press 3 times
Wireless adaptor plug switch IP 44 (Model ZW ZSA 3500)
...or...
press “UP” or
“DOWN” thrice
Start the inclusion step on the concerned controller of its network and
press the “FUNCTION” button of the equipment to be included thrice
within a span of 1.5 seconds.
Receiving frequency:
868.42 MHz
Switching capacity:
resitive 3,500 W
HV-Halogen, incandescent 1000 W
LV-Halogen, luminescent 690 VA
Operating voltage:
230 V, 50 Hz
NOTE: For information on handling or starting the inclusion step
of products of other manufacturers, please read the documents
of the respective manufacturer.
18
19
INTERACT3.
Wireless adaptor plug dimmer (model ZW ZDAN 300)
Receiving frequency:
Switching capacity:
868.42 MHz
HV, incandescent bulbs: 25 – 300 W
LV-Halogen with iron core transformer
40 – 300 VA
Operating voltage:
230 V, 50 Hz
Operating temperature: 0°C to +40°C
Microfuse:
T 1.25 A H
All the above-mentioned products (exception: ZW ZSA 3500)
comply with the norms only in indoor use: RTTE 1999/05/EG,
VDE 0620-1, EN 61058.
20
INTERACT3.
7. GUARANTEE:
The products of the INTERACT³ series are fabricated by means
of modern technology and are subjected to strict quality controls.
Should defects still occur in your equipments, the POPP GmbH
offers guarantee to the following extent.
1. Our guarantee offer comprises the repair or new delivery of
an equipment, if it exhibits a defect in the function or material
composition that can be proven.
2. The guarantee offer is not based upon the natural wear and
tear or transport damages or damages as a consequence of not
paying attention to the installation instructions as well as improper installation. One automatically loses the claim to the guarantee offer, if the equipment has been disassembled after diagnosis of errors.
21
INTERACT3.
INTERACT3.
3. The guarantee term amounts to 24 months from the date of
purchase by the end-user.
Remark: Note for well-versed users.
All-manufacturer Z-Wave-compatible programming functions:
The compliance of the claim period has to be proved by a statement of the purchase date by means of enclosed invoice, delivery note or similar documents.
To effect Include mode Press “INCL.” button of the controller
thrice
Batteries, LEDs and rechargeable batteries that are sent along
with the delivery are not covered by the guarantee offer.
To effect Include mode Press “EXCL.” button of the controller
for 2 seconds.
The POPP GmbH does not accept claims due to indirect, consequential and property damages.
Associate
Press “ASSOC.” button of the controller for 2 seconds, subsequently press
the “UP” button on the controller followed by the “send Node Info Frame”
of the target equipment.
Re-include/Replicate
Press the “INCL.” button of the controller thrice followed by the “send Node
Info Frame” of the target equipment.
If defects are observed in the equipment, please send the equipment
with enclosed description of the defect to the following address:
POPP GmbH
Kulmbacher Str. 27
D-95460 Bad Berneck
53916.14.02
22
July 2008
23
INTERACT3.
Disassociate
Press the “ASSOC.” button of the controller
for 2 seconds, subsequently the “DOWN”
button, followed by the “send Node Info
Frame” of the target equipment.
Learn Mode:
Press “UP” or “DOWN” button thrice.
Send Node Info Frame - press “UP” or “DOWN” button thrice
- (Controller) press “INCL.” for two
seconds
Add node
Press “UP” or “DOWN” button thrice
(inclusion or primary controller).
Please visit our website www.popp.eu in the internet and get
to know about further innovative products of the POPP GmbH,
such as e.g. the professional power outlet strip adaptus ®
INTERACT³ with integrated Z-Wave radio technology.
POPP GmbH
Kulmbacher Straße 27
D-95460 Bad Berneck
www.popp.eu
24
25