AG Neovo F-17C Specifications

Table of Content
PRECAUTIONS ................................................................................................. 2
INSTALLATION .................................................................................................... 2
POWER CONNECTION ......................................................................................... 2
USING THE TILT ................................................................................................. 2
MAINTENANCE ................................................................................................... 3
TRANSPORTING THE MONITOR ............................................................................. 3
GETTING STARTED ......................................................................................... 4
PACKAGE CONTENTS .......................................................................................... 4
INSTALLING AND REMOVING THE BASE ................................................................. 5
IDENTIFYING PARTS AND CONTROLS ..................................................................... 6
SETUP .............................................................................................................. 7
CUSTOMIZING YOUR MONITOR ..................................................................... 9
WORKING WITH OSD GROUPS ........................................................................... 9
TROUBLESHOOTING..................................................................................... 12
ATTENTION...................................................................................................... 12
LCD PANEL DISPLAY TECHNICAL FEATURES AND SPECIFICATIONS... 13
INTERFACE FREQUENCY ................................................................................... 14
REGULATIONS ............................................................................................... 15
FCC COMPLIANCE ........................................................................................... 15
INFORMATION FOR USERS APPLICABLE IN EUROPEAN UNION COUNTRIES ................ 16
INFORMATION FOR USERS APPLICABLE IN UNITED STATES OF AMERICA .................. 16
TCO'99.......................................................................................................... 17
1
Precautions
Installation
•
Do not cover or block the ventilation ports on the rear of the monitor.
•
Do not install the monitor close to heat sources such as radiators or air ducts, or
in a location exposed to direct sunlight, excessive dust, mechanical vibration, or
shock.
Power connection
•
Use the correct power cord for your local voltage.
•
Use an accessible outlet close to the monitor.
•
Do not allow anything to rest on the power cable.
•
Disconnect the power cable from the power supply if:
You will not use the monitor for an extended period.
The cable is damaged or frayed.
The monitor has been dropped or the cabinet damaged.
A distinct change in performance indicates a need for servicing.
Using the Tilt
•
Use the monitor’s tilt capability to adjust its vertical orientation to an appropriate
position. Grasp the top corners of the monitor with both hands and tilt to the
desired angle.
+30
-5
2
Maintenance
•
Clean the cabinet and controls with a soft cloth lightly moistened with a mild
detergent solution. Do not use any abrasive materials or solvents such as alcohol
or benzene.
•
Do not rub, touch, or tap the surface of the screen with sharp or abrasive items
such as pens or screwdrivers, as the screen may scratch.
•
Do not insert objects or spill liquids into the ventilation ports on the monitor’s rear,
as fire, electric shock, and/or unit failure may result.
Transporting the monitor
When transporting the monitor for repair or shipment, use the original carton and
packing materials.
3
Getting Started
Package contents
Before beginning, ensure that the carton contains the following items:
•
Monitor
•
Base
•
Power cord
•
CD-ROM containing Windows® information file
•
Quick Guide
4
Installing and Removing the Base
To attach the base to the monitor, do the following:
When you open the packing carton, remove the LCD monitor base, and place it on a
desk or table. Then attach the LCD monitor to the base.
Note:
Make sure that the monitor’s base pegs and the base stand are firmly
locked together.
To remove the base, turn the monitor on its side or up-side down, push the pegs to lift
base off monitor.
5
Identifying parts and controls
The center front panel of the monitor carries the control array.
FRONT VIEW
The controls are, from left to right:
AUTO button
Automatically adjusts the picture and performance. The AUTO function
should be used the first time you use the monitor and after changing the
resolution and/or refresh rate of the input signal.
Note:
1) It must be pressing the AUTO button over 1 second to execute auto
adjustment.
2) If the OSD is acting, this key function will same as down button.
LEFT button
Navigates within the display
RIGHT button
Navigates within the display
DOWN button
Activates the OSD and navigates within the display
UP button
Activates the OSD and navigates within the display
LED indicator
Indicates the monitor’s operational mode; green for regular operation, and
amber for power saving mode.
Power switch
Turns the monitor on and off
6
Setup
Follow these directions to correctly set up your monitor.
1.
Remove all packing materials and wrapping from the monitor
2.
Place the monitor in its desired location. Ensure that there is space around the
monitor, especially the rear area.
3.
With the computer turned off, connect the signal cable to the VGA port on your
PC. Make sure connection is secure.
4.
With the monitor switched off, connect the power cord to the Monitor AC socket.
5.
Connect the plug Pin of power cord to an AC power source.
AC Power Jack
Power Cord
6.
Turn on the computer.
7.
Press the power switch on the monitor. The display should appear. If no display
appears, check Troubleshooting in this manual.
8.
Ensure that your computer display is set at 1024X768 pixels and 60Hz. Press the
AUTO button
automatically.
exceed 1 second. The monitor optimizes the display
7
Note:
The monitor is compliant with VESA FPMPMI standards and can be wall- or
arm-mounted. Before wall-mounting or arm-mounting, please disassemble
the monitor stand first.
1.
Unscrew screws of the hinge bracket
2.
Remove the stand from LCD monitor
1
2
3.
The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded
nuts, as well as four 5 mm access holes in the plastic covering as illustrated
below. These specifications meet the VESA Flat Panel Monitor Physical
Mounting Interface Standard (paragraphs 2.1 and 2.1.3, version 1, dated 13
November 1997).
75mm x 75mm
Screw Mounting Options
75mm
75mm
4mm ,0.7pitch threaded holes x4
8
Customizing your Monitor
The On Screen Display (OSD) system provides a full range of customizable tools to
optimize your display.
Important:
While full customization is available, we strongly recommend using
the AUTO settings, which are preset to fully optimize your monitor’s
performance. Simply presses the AUTO button
exceed 1 second
to engage the AUTO settings. It is also recommended that you
execute the AUTO function following any change made to your
display from your computer.
Working with OSD Groups
Press any of the LEFT
, or RIGHT
buttons to open the OSD window.
OSD Function Menu
To access OSD Main menu, simply press
one of the Function Select control buttons,
and the menu diagram will pop up on the
screen as shown on Fig. 1-1:
Continue pressing the Function Select
buttons (left/right) to scroll through the
entire menu items , then press Adjustment
Control buttons (up/down) to adjust content
of selected item.
Attention Firmware revision may have been updated into a latest version while
the version number shown on all OSD menus in this manual will stay as
Ver. 1.00.
Brightness & Contrast
/
•
To fine-tune the monitor’s brightness and contrast, select the pertinent item from
the menu.
•
Use the UP
and DOWN
buttons to set the display as desired on the 0-100
scales that appears at the bottom of the window.
Horizontal & Vertical Position
/
•
To fine-tune the display’s position on the monitor screen, select the pertinent item
from the menu.
•
Use the UP
and DOWN
buttons to set the display as desired on the 0-100
scales that appears at the bottom of the window.
Sharpness
•
This function let's you select the images sharpness. Five selections are available.
A smoother setting is more suitable for pictures, while a sharper setting is more
suitable for text.
•
Use the UP
desired.
and DOWN
buttons to set the display image sharpness as
9
OSD Transparency
•
This function let's you set the transparency of the OSD menu. The transparency is
adjustable from 0 to 3. 4 scales are available.
•
Use the UP
desired.
and DOWN
Phase & Clock
/
buttons to set the transparency of OSD manu as
•
To fine tune picture performance to compensate for drifts in the computer signal,
select the pertinent item from the menu.
•
Use the UP
and DOWN
at the bottom of the window.
buttons to set the display as desired that appears
Auto Adjust
•
To enable the monitor’s Auto Adjust capability, select Auto Adjust from the menu.
•
and DOWN
Use the UP
at the bottom of the window.
buttons to toggle between YES and NO as desired
Horizontal & Vertical OSD Position
/
•
To position the OSD window to your preference, select OSD Position from the
menu.
•
Use the UP
positions.
and DOWN
buttons to move the display through its available
Mode Text/Graphics
•
To choose between the monitor’s automatic Sharpness optimization for Text or
Graphic use, select Mode Text/Graphic from the menu.
•
and DOWN
buttons to toggle between TEXT and GRAPHIC as
Use the UP
desired at the bottom of the window.
Note:
For better performance, please change to “Text” mode when display
resolution is set at 720 x 400 and change to “Graphics” mode when
display resolution is set to 640 x 400.
•
Recall
•
To return the monitor’s settings to the factory default, select Recall from the menu.
•
Use the UP
and DOWN
at the bottom of the window.
buttons to toggle between YES and NO as desired
Selecting a Language
•
To select the language in which you wish the OSD to appear, select Language
from the menu.
•
Use the UP
and DOWN
buttons to toggle through the available languages
shown at the bottom of the window.
10
Selecting a Color Temperature setting
The following conditions are recommended for the available settings:
Setting
Use
9300K
6500K
USER
Auto Color
General Use
Color Management
User color setting
Auto adjust to best ADC gain value.
Select the desired setting from the menu.
Selecting a User-Defined Color Balance Setting.
You can fine-tune the red/green/blue picture settings according to your
preference or specific application.
Select the pertinent color category from the menu.
Use the UP
and DOWN
buttons to set the display as desired on the
0-100 scale or run auto color adjust function when select to auto color
function.
Exit
Select EXIT from the menu to exit the OSD menu.
11
Troubleshooting
This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the
output timing differences among various VGA cards in the market, users may initially
experience an unstable or unclear display whenever a new display mode or new VGA
card is selected.
Attention
This LCD Monitor Supports Multiple VGA Modes.
Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor.
PROBLEM
Check Items
•
Picture is unclear
and unstable
The picture is unclear and unstable, please perform the
following steps:
♦ Enter PC to “Shut Down Windows” status while you’re
in MS-Windows environment.
♦ Check the screen to see if there’s any black vertical
stripes appear. If there are, take advantage of the
“Clock” function in OSD menu and adjust (by increment
or decrement numbers) until those bars disappear.
♦ Move to “Phase” function in OSD menu again and
adjust the monitor screen to its most clear display.
♦ Click “No” on “Shut Down Windows” and back to the
normal PC operating environment.
•
There is no picture
on LCD Monitor
•
There is no picture
on LCD Monitor
If there’s no picture on the LCD Monitor, please perform the
following steps:
♦ Make sure the power indicator on the LCD Monitor is
ON, all connections are secured, and the system is
running on the correct timing. Refer to “Supported
Timing List” for information on timing.
♦ Turn off the LCD Monitor and then turn it back on
again. If there is still no picture, press the Adjustment
Control button several times.
♦ If step 2 doesn’t work, connect your PC system to
another external CRT. If your PC system Functions
properly with a CRT Monitor but it does not function
with the LCD Monitor, the output timing of the VGA
card may be out of the LCD’s synchronous range.
Please change to an alternative mode listed in the
Supported Timing List or replace the VGA card, and
then repeat steps 1 and 2.
If you have chosen an output timing that is outside of the
LCD Monitor’s synchronous range (Horizontal: 24 ~ 80 KHz
and Vertical: 49 ~ 75 Hz), the OSD will display a “Out of
Range” message. Choose a mode that is supported by your
LCD Monitor.
Also, if the signal cable is not connected to LCD monitor at
all or properly, the monitor screen will display a message “No
Input Signal”.
12
LCD Panel Display Technical Features and
Specifications
Panel
Monitor
Input Signal
Screen Size
17" (43cm) diagonal
Pixel Format
1280 x 1024 vertical strip
Display Colors
16.7M with FRC or Dithering
Horizontal: 24kHz - 80kHz,
Frequency
Vertical: 49Hz - 75Hz
Max. Pixel Clock
135MHz
PC
Max to 1280 x 1024 @ 75Hz
Analog
15-Pin Mini D-Sub
Power
3-Pin AC Inlet
Tilt
Tilt Angle
-5º - +30º
Dimensions
(W x H x D)
Net
Weight
Net
5Kg (11 lb)
Safety
UL/CUL, EPA, CB, TUV/GS, Nordic,
NUTEK, TCO99, ISO 13406-2
EMI
FCC, CE, BSMI, VCCI
VESA
DDC1/2B, DPMS
Compatibility
Connector
Regulations
377 x 373 x 200mm
(14.8" x 14.7" x7.9")
100 ~ 240V,
AC
50 /60Hz
Power
< 35 Watts (On),
Consumption
< 3 Watts (Stand-by),
< 2 Watts (Off)
13
Interface Frequency
The following frequency range is the working period. If the entered mode between below
period but not match the frequency of supported timing, display optimization not be
assured. If the entered mode is out of the working period, the display will be blanking
(just show “out of range”) then go to power saving.
Basically, mode judgment is regardless the sync polarity except both or more modes
that are all belong to the supported timing list and could be judged by sync polarity only.
At the meantime, real entered frequency of the supported timing is not requested
exactly. Normalization of VGA card’s deviation will be acceptable.
•
Horizontal Frequency 24KHz ---80KHz
•
Vertical Frequency
49Hz -------75Hz
14
Regulations
FCC compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Any unauthorized modification to this equipment could result in the
revocation of the authorization to operate the equipment and void the
product warranty.
15
Information for users applicable in European Union
countries
The symbol on the product or its packaging signifies that this product has to be
disposed separately from ordinary household wastes at its end of life. Please
kindly be aware that this is your responsibility to dispose electronic equipment
at recycling centers so as to help conserve natural resources. Each country in
the European Union should have its collection centers for electrical and
electronic equipment recycling. For information about your recycling drop off
area, please contact your local related electrical and electronic equipment
waste management authority or the retailer where you bought the product.
Information for users applicable in United States of
America
LAMP(S) inside this product contain mercury and must be recycled or disposed
of according to local, state or federal laws. For more information, contact the
electronic industries alliance at www.eiae.org. for lamp specific disposal
information check www.lamprecycle.org.
16
TCO'99
Congratulations!
You have just purchased a TCO'99 approved and labeled product! Your choice has provided you with
a product developed for professional use. Your purchase has also contributed to reducing the burden
on the environment and also to the further development of environmentally adapted electronics
products.
Why do we have environmentally labeled computers?
In many countries, environmental labeling has become an established method for encouraging the
adaptation of goods and services to the environment. The main problem, as far as computers and
other electronics equipment are concerned, is that environmentally harmful substances are used both
in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the
majority of electronics equipment, most of these potentially damaging substances sooner or later enter
nature.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (internal) and natural (external) environments. Since all
methods of electricity generation have a negative effect on the environment (e.g. acidic and climateinfluencing emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is
often left running continuously and thereby consumes a lot of energy.
What does labeling involve?
This product meets the requirements for the TCO'99 scheme which provides for international and
environmental labeling of personal computers. The labeling scheme was developed as a joint effort by
the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen
(The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National
Energy Administration).
Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of
electric and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands impose restrictions on the presence and use of heavy metals, brominated
and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The
product must be prepared for recycling and the manufacturer is obliged to have an environmental
policy which must be adhered to in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time
to reactivate the computer shall be reasonable for the user.
Labeled products must meet strict environmental demands, for example, in respect of the reduction of
electric and magnetic fields, physical and visual ergonomics and good usability.
Below you will find a brief summary of the environmental requirements met by this product. The
complete environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO'99 approved and labeled products may also be obtained via the
Internet, using the address: http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their
purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer
casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride,
and those flame retardants are chemically related to another group of environmental toxins, PCBs.
Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to
severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio17
accumulative* processes. Flame retardants have been found in human blood and researchers fear that
disturbances in foetus development may occur.
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not
contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in
the printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99
requirement states that batteries, the colour-generating layers of display screens and the electrical or
electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is
toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any
mercury. It also demands that mercury is not present in any of the electrical or electronics components
associated with the labeled unit.
CFCs
(freons)
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed
circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere,
causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer
(malignant melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning. The relevant TCO´99 requirement
permits the inclusion of lead since no replacement has yet been developed.
*
**
Bio-accumulative is defined as substances which accumulate within living organisms
Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
18