R
Model CD5000 User Guide
CD PLAYER
Downloaded From Disc-Player.com Marantz Manuals
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
LASER SAFETY
This unit employs a laser, Only a qualified service person should remove the cover or attempt to service this
device, due to possible eye injury.
CAUTION
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Downloaded From Disc-Player.com Marantz Manuals
2
English
Français
English ....................................................4
Français.................................................14
NOTE :
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
This Class B digital apparatus meets all
requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la Classe B
respecte toutes les exigences du Règlement
sur le matérier brouilleur du Canada.
NOTE : Changes or modifications may cause
this unit to fail to comply with Part 15 of the FCC
Rules and may void the user’s authority to
operate the equipment.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
Downloaded From Disc-Player.com Marantz Manuals
3
SAFETY INSTRUCTIONS –
Read before operating equipment
English
This product was designed and manufactured to meet strict quality and
safety standards. There are, however, some installation and operation
precautions which you should be particularly aware of.
1. Read Instructions - All the safety and operating instructions should be
read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be
retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating
instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be
followed.
5. Water and Moisture - The appliance should not be used near water for example, near a bathtub, washbowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement.
6. Carts and Stands - The appliance should be used only with a cart or
stand that is recommended by the manufacturer.
6A.
An appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.
7. Wall or Ceiling Mounting - The appliance should be mounted to a
wall or ceiling only as recommended by the manufacturer.
8. Ventilation - The appliance should be situated so that its location or
position does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug, or similar surface
that may block the ventilation openings; or, placed in a built-in
installation, such as a bookcase or cabinet that may impede the flow of
air through the ventilation openings.
9. Heat - The appliance should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
10. Power Sources - The appliance should be connected to a power
supply only of the type described in the operating instructions or as
marked on the appliance.
11. Grounding or Polarization - Precautions should be taken so that the
grounding or polarization means of an appliance is not defeated.
12. Power Cord Protection - Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords and plugs,
convenience receptacles, and the point where they exit from the
appliance.
13. Cleaning - The appliance should be cleaned only as recommended by
the manufacturer.
14. Power Lines - An outdoor antenna should be located away from power
lines.
15. Outdoor Antenna Grounding - If an outside antenna is connected to
the receiver, be sure the antenna system is grounded so as to provide
some protection against voltage surges and built up static charges.
Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984,
provides information with respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding connectors, location of antennadischarge unit, connection to grounding electrodes, and requirements for
the grounding electrode. See figure below.
16. Non-use Periods - The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of time.
17. Object and Liquid Entry - Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through openings.
18. Damage Requiring Service - The appliance should be serviced by
qualified service personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a
marked change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
19. Servicing - The user should not attempt to service the appliance
beyond that described in the operating instructions. All other servicing
should be referred to qualified service personnel.
Caution: To prevent electric
shock, match the wide blade of this
plug to the wide slot and fully insert.
AC
Do not use this (polarized) plug with an
Polarized Plug
extension cord, receptacle or other
outlet unless the blades can be fully inserted to prevent blade exposure.
Note to the Cable TV system installer
This reminder is provided to call the Cable TV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as
practical.
Example of Antenna Grounding as
per NEC - National Electrical Code
Ground Clamp
Antenna Lead-in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductors
(NEC Section 810-21)
Ground Clamps
Electric Service Equipment
Downloaded From Disc-Player.com Marantz Manuals
4
Power Service Grounding Electrode System
(NEC Art. 250, Part H)
GENERAL INFORMATION
GENERAL INFORMATION
Maintenance ................................................................5
Technical data ..............................................................5
CONTROLS AND CONNECTIONS
Controls on the front....................................................6
Connections at the back ..............................................6
INSTALLATION AND REMOTE CONTROL
Accessoires ..................................................................7
Connections
Usual connection, LINE OUT ....................................7
Digital connection, DIGITAL OUT.............................7
Mains ...........................................................................7
Remote control.............................................................7
Batteries ...................................................................7
PLAYBACK
CD Text .........................................................................8
Discs for playback........................................................8
Playing a CD.................................................................8
ADDITIONAL FUNCTIONS
Selecting a track and searching
Selecting a track during CD play .............................9
Selecting a track when CD play is stopped.............9
Searching for a passage during CD play .................9
Random order playing (SHUFFLE) ................................9
Repeating a CD, a track or a program.........................9
Repeating a part of the CD..........................................9
Programming track numbers......................................10
Clearing the program .................................................10
Loudest passage searching .......................................10
Time display ...............................................................10
Fading out and in .......................................................11
Volume adjustment ....................................................11
Locking the volume ....................................................11
Headphone listening ..................................................11
Scanning the CD ........................................................11
Recording setup .........................................................12
Environmental information.........................................12
TROUBLESHOOTING
Warning......................................................................13
Troubleshooting..........................................................13
Maintenance
English
Table of contents
Clean the CD player with a soft,
slightly dampened lint-free cloth. Do
not use any cleaning agents as they
may have a corrosive effect.
Do not expose the CD player,
batteries or CDs to humidity, rain,
sand or excessive heat (caused by
heating equipment or direct sunlight).
This CD player can play all kinds of Audio Discs such as
CD-Recordables, CD-Rewriteables and CD-Text CDs. Do not
try to play a CD-ROM, CD-I, CDV or computer CD.
If the CD player cannot read CDs correctly use a commonly
available cleaning CD to clean the lens before taking the CD
player to repair. Other cleaning methods may destroy the lens.
Always keep the tray closed to avoid dust on the lens.
The lens may cloud over when the CD player is suddenly
moved from cold to warm surroundings. Playing a CD is not
possible then. Leave the CD player in a warm environment
until the moisture evaporates.
To clean a CD, wipe it in a straight
line from the center toward the edge
using a soft, lint-free cloth. A
cleaning agent may damage the disc!
Never write on a CD or attach a
sticker to it.
Technical data
Subject to modification without notice.
Standby power consumption .............................................< 5W
Frequency range ....................................................20–20,000Hz
Amplitude linearity ..................................< 0.5dB (1kHz, -90dB)
Dynamic range.........................................................98dB (1kHz)
Signal-to-noise ratio.........................108dB (1kHz, A-weighted)
Channel separation..................................................98dB (1kHz)
Total harmonic distortion.........................0.004%, -88dB (1kHz)
Audio output ...............................................2V RMS ±3dB, 1kΩ
Digital coaxial output.....................................75Ω acc. IEC 958
Digital optical output .....................................................-19dBm
Impedance headphones .......30–600Ω (5V e. m. f. from 120Ω)
Dimensions ..................................................435 × 86 × 265mm
Weight................................................................................2.9kg
Downloaded From Disc-Player.com Marantz Manuals
5
CONTROLS AND CONNECTIONS
English
2
4
7 8 9
0
! @
CD PLAYER CD5000
PLAY
OPEN/CLOSE
HIGHLIGHT
SHUFFLE
FADE
PROG
EDIT
PEAK
$ %
#
STOP
CD TEXT
SCROLL
PREV
PAUSE
NEXT
TIME
POWER ON/STANDBY
PHONES
LEVEL
CD REWRITABLE PLAYBACK
1
3
Controls on the front
1 POWER ON / STANDBY...switches the CD player on and
to standby
2 OPEN·CLOSE......................opens and closes the CD tray
3 Sensor for the infrared remote control
4 Display
5 TIME ....................................switches through the different
time information
6 SCROLL ...............................scrolls CD-Text information
7 CD TEXT..............................switches through the different
CD-Text information
8 HIGHLIGHT.........................plays the beginning of each
track or – if a CD-Text disc
contains highlights – the
highlights of a CD
9 SHUFFLE .............................plays a CD or a program in
random order
0 FADE....................................fades CD play out and in
5
6 ) (
*
&
^
! PREV. ∞ .............................selects the beginning of the
current or a previous track,
and searches backward
@ PLAY 2................................starts CD play
# PAUSE ;..............................interrupts CD play
$ STOP 9 ...............................stops CD play and clears a
program
% NEXT §..............................selects the beginning of a
subsequent track, and
searches forward
^ VOLUME .............................decreases or increases the
volume level of the
headphones
& PHONES..............................6.3mm headphone socket
* PEAK ...................................searches the loudest passage
of a CD
( EDIT .....................................changes the settings for
recording on tape or
CD-Recordable
) PROGRAM..........................programs track numbers
21
23
Connections at the back
¡ COAXIAL / OPTICAL
DIGITAL OUT......................to connect the digital input of
a digital audio device
™ LINE OUT L R .....................to connect the audio input of
an amplifier
£ MAINS LEAD .....................After all other connections
have been made, connect this
mains lead to the wall socket.
Downloaded From Disc-Player.com Marantz Manuals
6
22
INSTALLATION AND REMOTE CONTROL
PRO
TIM
E
GRA
M
1
FAD
ER
4
3
SCAN
8
9
RE
T
A
PE
SC
+
NEX
T
PA
USE
XT
0
VO
LU
ME
PL
AY
EV
.
ST
OP
CD
TE
6
–
PR
y
LE
UFF
SH
2
7
5
This CD player is supplied including:
– a remote control
– 2 batteries for the remote control
– a connection cable
– this instruction booklet
Remote control
English
Accessories
RO
LL
RE
PE
AT
A/B
Connections
Usual connection, LINE OUT
1 Insert the red plug of the supplied connection cable into R
and the other plug into L.
2 Insert the other side of the cable into the corresponding
sockets of the CD or AUX input of your amplifier.
Important!
You may also use the TUNER or TAPE, but never the PHONO
input of your amplifier!
Digital connection, DIGITAL OUT
Never connect this socket to a non-digital input – such as
AUX, CD, PHONO, TAPE – of an amplifier. This output supplies
a digital signal and can therefore only be connected to a
digital input.
1 Insert an optional coaxial cable into DIGITAL OUT.
2 Insert the other side of the cable into the digital input of
your digital device (e. g. CD Recorder).
Mains
The type plate is located on the bottom of the CD player.
1 Check whether the mains voltage as shown on the type
plate corresponds to your local mains voltage. If it does not,
consult your dealer or service organisation.
2 Connect the mains cable to the wall socket. This switches
on the mains supply.
Note: To disconnect the CD player from the mains completely,
remove the mains plug from the wall socket.
Batteries
• Open the battery compartment of the remote control and
insert 2 alkaline batteries, type AAA (R03, UM-4).
Remove batteries if they are flat or the remote control is not
going to be used for a long time.
Batteries contain chemical substances, so they should
be disposed of properly.
TIME......................switches through the different time
informations
y ............................switches the CD player to standby
PROG.....................programs track numbers
FADE......................fades CD play out and in
SHUFFLE ...............plays a CD or a program in random order
DIGITS 0–9 ...........selects a track by number
HIGHLIGHT...........plays the beginning of each track or – if a
CD-Text disc contains highlights – the
highlights of a CD
REPEAT .................repeats a track, a program or the entire
CD
VOLUME – ............decreases the volume level
VOLUME + ............increases the volume level
PLAY 2..................starts CD play
PREV. ∞ ...............selects the beginning of the current or a
previous track
NEXT §................selects the beginning of a subsequent
track
STOP 9 .................stops CD play and clears a program
5...........................searches backward
PAUSE ;................interrupts CD play
6...........................searches forward
CD TEXT................switches through the different CD-Text
information
SCROLL .................scrolls CD-Text information
REPEAT A/B .........repeats a selected part of the CD
Downloaded From Disc-Player.com Marantz Manuals
7
PLAYBACK
English
CD PLAYER CD5000
PLAY
OPEN/CLOSE
HIGHLIGHT
SHUFFLE
FADE
PROG
EDIT
PEAK
STOP
CD TEXT
SCROLL
PREV
PAUSE
NEXT
TIME
POWER ON/STANDBY
PHONES
LEVEL
CD REWRITABLE PLAYBACK
CD-Text
Playing a CD
This CD player can show information which is stored on CDText discs. It will only reproduce the text which is recorded on
the disc.
1 Use POWER ON / STANDBY to switch on the CD player.
1 When inserting a disc with CD-Text the display shows
CD TEXT and performing artist or group. In case there are
various artists the album title is shown.
2 Press CD TEXT before playing a CD to switch between
album title and performing artist(s) if available.
3 Press CD TEXT during CD play to switch between album
title, performing artist(s) and track title if available.
4 At the beginning of a new track the track title is scrolled
once. Then the first 12 digits of the track title are
displayed.
2 Press OPEN·CLOSE to open the CD tray.
y OPEN appears on the display.
3 Insert an audio CD (printed side up) and press OPEN·CLOSE
to close the CD compartment.
y READING appears on the display. Then the number
of tracks and the playing time is shown. If the disc
contains CD-Text the display shows CD TEXT and
CD-Text information (see “CD-Text”).
4 Press PLAY 2 to start CD play.
y The display shows
, TRACK, TIME, and the number and
time of the actual track. If the disc contains CD-Text the
display shows CD-Text information.
5 CD-Text information is scrolled every 30 seconds. Press
SCROLL to scroll the text through the display any time.
• You can interrupt CD play by pressing PAUSE ;.
y The display shows
and the track number and time
where playback was stopped.
• Continue CD play by pressing PAUSE ; again.
Discs for playback
5 Press STOP 9 to stop CD play.
This system can play all audio CD, finalized audio CDRecordable and finalized audio CD-Rewritable format discs.
Downloaded From Disc-Player.com Marantz Manuals
8
Note: Playback will also stop if the end of the CD is reached.
T
SHUFFLE
FADE
EDIT
PEAK
Random order playing (SHUFFLE)
PREV
PAUSE
PHONES
NEXT
LEVEL
1 Press SHUFFLE before or during CD play to start shuffle
play.
y SHUFFLE is shown in the display. All the tracks of the CD
(or program if available) will now be played in random
order.
2 Press SHUFFLE again to return to normal CD play.
Selecting a track and searching
Selecting a track during CD play
• Briefly press PREV. ∞ or NEXT § once or several times to
skip to the beginning of the current, previous or subsequent
track(s).
or
• Use the digits 0–9 on the remote control to key in the
number of a track.
y CD play continues with the selected track.
Repeating the CD, a track or a program
1 Press repeatedly REPEAT on the remote control during CD
play.
y The display shows the different repeating modes.
REPEAT 1: the current track is played repeatedly.
REPEAT: the entire CD or program (if available) is played
repeatedly.
2 Press REPEAT until the display indication disappears to
return to normal CD play.
Selecting a track when CD play is stopped
1 Briefly press PREV. ∞ or NEXT § once or several times.
or
• Use the digits 0–9 on the remote control to key in the
number of a track.
Note: It is possible to activate the different playing modes at
the same time, e. g. you can repeatedly play the entire
CD or program in random order (PROGRAM REPEAT SHUFFLE).
2 Press PLAY 2 to start CD play.
y Playback starts with the selected track.
1 Press PLAY 2 to start CD play.
Searching for a passage during CD play
1 Hold down PREV. ∞ or NEXT § to find a particular
passage in a backward or forward direction.
y CD play continues at a low volume.
2 Release the button when you have reached the desired
passage.
Note: In the shuffle and repeat mode and when playing a
program, searching is only possible within the
particular track.
Repeating a part of the CD
2 Press REPEAT A/B on the remote control to mark the
beginning of the passage to be repeated.
y REPEAT is shown and A- is flashing in the display.
3 Press REPEAT A/B on the remote control to mark the end of
the passage to be repeated.
y REPEAT A-B is shown in the display. The part of the CD
between the marked points is played repeatedly.
4 Press PLAY 2 to return to normal CD play.
Downloaded From Disc-Player.com Marantz Manuals
9
English
ADDITIONAL FUNCTIONS
ADDITIONAL FUNCTIONS
English
HIGHLIGHT
SHUFFLE
FADE
CD TEXT
SCROLL
Clearing the program
1 If necessary press STOP 9 to stop program playing.
PROG
EDIT
PEAK
TIME
2 Press STOP 9 to clear the program.
y PROGRAM CLEARED scrolls through the display,
PROGRAM disappears and your program is cleared.
Note: The program will also be cleared if you open the tray.
Programming track numbers
Loudest passage searching
You can select a number of tracks and store these in the
memory in the desired sequence. You can store any track
more than once. At most, 30 tracks can be stored in the
memory.
You can search for the loudest passage of a CD or program.
This will help you in adjusting your recording device if
required.
1 Press PROG to start programming.
y PROGRAM flashes.
Note: If you press PROG while playing a CD, the actual track
will be added to the program.
2 Press PREV. ∞ or NEXT § to select the desired track.
or
• Key in the number of a track with the digits 0–9 on the
remote control.
3 Press PROG to store the track number.
y TRACK, TOTAL TIME, and the number of the programmed
track is displayed. The number of programmed tracks is
increased and the time of the track is added to the total
time of the program.
4 Repeat steps 2 and 3 for all tracks to be programmed.
5 Press STOP 9 to end programming.
y PROGRAM lights permamently.
• It is possible to review the program using the PREV. ∞ or
NEXT §. You can add more tracks by pressing PROGRAM
like you have done before.
6 Press PLAY 2 to start program play.
Note: If you try to store more than 30 tracks
PROGRAM FULL scrolls through the display.
1 If necessary press STOP 9 to stop CD play.
2 Press PEAK to start searching.
y PEAK starts flashing. Searching may need a few
minutes. Then 4 seconds of the loudest passage are
played repeatedly.
• You can interrupt peak play by pressing PAUSE ;. Continue
peak play by pressing PAUSE ; again.
3 Press STOP 9 to stop playing.
or
• Press PLAY 2 to start CD play.
Time display
You can display time information which is stored on the CD.
While playing a CD or a program the number and elapsed
time of the actual track, and TIME are displayed. If the disc
contains CD-Text the display shows CD-Text information (see
“CD-Text”).
• Press TIME several times to display:
y If the disc contains CD-Text, the number and elapsed
time of the actual track, and TIME are displayed first.
y The number and remaining time of the actual track, and
REM TIME.
y The number of the actual track, the total elapsed time
of the CD, and TOTAL TIME.
y The number of the actual track, the total remaining time
of the CD, and TOTAL REM TIME.
Note: If you press TIME when the CD is not playing you may
only display the total time of the CD.
Downloaded From Disc-Player.com Marantz Manuals
10
ADDITIONAL FUNCTIONS
SHUFFLE
STOP
FADE
Headphone listening
English
PLAY
HIGHLIGHT
1 Connect your headphones to the 6.3mm PHONES socket.
PROG
EDIT
PEAK
PREV
PHONES
PAUSE
NEXT
LEVEL
2 Use LEVEL to adjust the volume of the headphones.
Note: The maximum volume on the headphones is set through
VOLUME –/+ on the remote control.
Important!
Fading out and in
The volume of the headphones is in line with the volume of the
output. Therefore do not use VOLUME –/+ during recording.
You can fade out and in CD play, e. g. to stop and start a
recording softly.
Scanning the CD
1 Press FADE during CD play to fade out.
y The display shows
in steps. The volume is lowered
continuously until CD play is paused.
2 Press FADE again to fade in.
y The display shows
in steps. CD play starts and the
volume is raised continuously to its previous level.
Note: You may use FADE anytime when CD play is paused to
fade in.
It is possible to listen to the beginning of each track of a CD
or program. You can choose whether to play 10, 20 or 30
seconds of each track. If a disc contains CD-Text highlights
this part of the tracks is scanned and HIGHLIGHT is
displayed.
1 Press HIGHLIGHT repeatedly to switch through the different
scan modes.
y SCAN 10, SCAN 20, SCAN 30, SCAN
OFF… (SCAN OFF aborts the scan function).
The volume of the CD player can be adjusted. This affects the
DIGITAL OUT output as well.
2 As soon as the desired scan mode is displayed do not press
the button again.
y After 1 second scanning starts. The number and
remaining time of the actual track, and REM TIME are
displayed.
• Press VOLUME – or VOLUME + on the remote control.
y The volume of the CD player is lowered or raised. The
display shows the actual value between
VOLUME MIN and VOLUME MAX.
• You can interrupt scan by pressing PAUSE ;. Continue scan
by pressing PAUSE ; again.
Important!
3 Press STOP 9 to stop scanning.
or
• Press PLAY 2 to start CD play with the actual track.
Volume adjustment
VOLUME –/+ is altering the signal of the output. Before
recording set the volume to VOLUME MAX and do not
change during recording.
Note: If you press HIGHLIGHT while SHUFFLE is active,
shuffle will be stopped before scanning.
Locking the volume
It is possible to lock the output volume to its maximum. This
affects the DIGITAL OUT output as well. Locking the volume
can be usefull when recording from the CD-player.
• Keep EDIT pressed for more than 2 seconds.
If the voulme was unlocked:
y The display shows VOLUME FIXED and the
volume is locked.
If the voulme was locked:
y The display shows VOLUME MAX and the volume is
unlocked.
Note: If you press VOLUME –/+ and the volume is locked the
display shows VOLUME FIXED.
Downloaded From Disc-Player.com Marantz Manuals
11
ADDITIONAL FUNCTIONS
PLAY
English
HIGHLIGHT
SHUFFLE
FADE
PROG
EDIT
PEAK
PREV
STOP
PAUSE
PHONES
5 Press PREV. ∞ or NEXT § to switch through the different
recording times and media.
y C 100, C 120, CDR 21, CDR 60,
CDR 74, C 30, C 45, C 60, C 90…
NEXT
LEVEL
Recording setup
It is possible to set up the CD player in a way that it will
calculate which tracks will fit on your recording media. It is
only possible to use the edit function if a disc has not more
than 29 tracks.
If you use NORMAL the recording stops after the last track
that fits on one side of your recording media. Notice that CDRecordables are single-sided only! If you use OPTIMAL
some tracks will be skipped to minimise the unused space on
your recording media. The sequence of the tracks stays as the
original.
Note: C is for cassette, CDR is for CD-Recordable and
CD-Rewriteable and therefore for single-sided
recording only.
6 As soon as the desired recording time and media is
displayed press EDIT.
y A, the number of tracks and the playing time are
displayed.
7 Start your recording and press PLAY 2 to start CD play.
y If cassette (C) was selected the CD player pauses after
playing the calculated tracks for side A. If CDRecordable (CDR) was selected the CD player stops.
8 If required switch tape sides.
9 Press PLAY 2 to start CD play again.
y B, the number of tracks and the playing time are
displayed. The remaining tracks for side B are played.
1 Insert a CD and, if desired, program track numbers.
2 Press EDIT to start the setup.
y The display shows NORMAL.
Note: It is possible to switch between A and B by using
PREV. ∞ or NEXT § .
3 Press PREV. ∞ or NEXT § to switch through the different
scan modes.
y NORMAL, OPTIMAL, STOP… (STOP aborts the
edit function).
4 As soon as the desired edit mode is displayed press EDIT.
y The display shows C 90.
Environmental information
All redundant packing material has been omitted. We have
done our utmost to make the packaging easily separable
into three mono materials: cardboard (box), polystyrene foam
(buffer) and polyethylene (bags, protective foam sheet).
Downloaded From Disc-Player.com Marantz Manuals
12
Your set consists of materials which can be recycled if
disassembled by a specialized company. Please observe the
local regulations regarding the disposal of packing
materials, exhausted batteries and old equipment.
WARNING
If a fault occurs, first check the points listed below before
taking the set for repair.
Under no circumstances should you try to repair the
CD player yourself as this will invalidate the
guarantee.
If you are unable to solve a problem by following this
checklist, consult your dealer or service center.
Problem
Possible cause
Solution
No power
Mains cable is not securely connected.
Connect mains cable properly.
No or bad sound
Volume is too low.
Interference caused by electric equipment
like TVs, computers, engines, etc.
Adjust volume.
Keep the CD player away from electrical
equipment.
Loose or wrong connections.
Volume is too low.
Headphone plug is dirty.
Volume is too low.
Connect the CD player correctly.
Adjust VOLUME –/+.
Clean headphone plug.
Adjust VOLUME –/+.
Loose or wrong connections.
Electrostatic discharge.
Connect the CD player correctly.
Disconnect the CD player from mains,
reconnect after a few seconds.
Insert a CD.
No or bad headphone
No or low quality
recording
No reaction to
operation of any keys
INSERT DISC
is displayed
DISC NOT
FINALIZED
is displayed
WRONG TRACK
is displayed
0 0:00 is displayed
VOLUME FIXED is
displayed
Some CD-Text track
information is not
displayed
CD skips tracks
Remote control does
not function properly
No CD is inserted.
The CD is badly scratched or dirty.
The CD is inserted upside down.
The CD-RW (or CD-R) is not properly recorded
for the use on a standard CD player.
English
TROUBLESHOOTING
Too much information on the CD-Text disc.
Replace or clean the CD.
Insert CD with label upwards.
Read the instruction booklet of your
CD-Rewriteable (or CD-Recordable) recorder
on how to finalize a recording.
Replace or clean the CD.
Key in a track number within the range of the
track numbers on the CD.
Choose a recording media with a recording time
longer than the first track of the CD.
Press EDIT for more than 2 seconds to
unlock the volume.
Use a CD-Text disc with less information.
SHUFFLE
or PROGRAM is active.
The CD is badly scratched or dirty.
Switch off SHUFFLE or PROGRAM play.
Replace or clean the CD.
Laser lens is dirty.
The laser lens is steamed up.
Batteries are inserted incorrectly.
Clean with a commonly available cleaning CD.
Wait until the lens has cleared.
Insert batteries correctly.
Batteries are flat.
Distance to the CD player is too large.
Insert fresh batteries.
Reduce distance.
The CD is badly scratched or dirty.
Chosen track number is higher than the
highest track number on the CD.
First track of the CD is longer than the first
side of the chosen recording media.
Volume is locked.
Downloaded From Disc-Player.com Marantz Manuals
13
Marantz America, Inc.
440 Medinah Road
Roselle, IL 60172-2330
Phone : (708) 307-3100
Fax : (708) 307-2687
is a registered trademark.
3139 116 19111
Downloaded From Disc-Player.com Marantz Manuals
Printed In Singapore
SL-9909/U1B-02