advertisement
ED910 & ED930
720p Analog High Definition
True Day/Night Indoor Dome Camera
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: Nov., 2014
Precautions
1. Do not install the camera near electric or magnetic fields. Install the camera away from
TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image or otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal circuits, as well as creating unbalanced illumination beyond the capability of the camera to compensate.
4. Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures within -10°C~50°C (14°F~122°F) and humidity between 20%~ 80%; this device is not rated as submersible. The input power source is 12VDC or 24VAC. Be sure to connect the proper + / - polarity and voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail, and such damage is not covered by the warranty.
8. Mounting. Use care in selecting a solid mounting surface which will support the weight of the camera plus any wind, snow, ice or other loading, and securely attach the camera to the mounting surface using screws and anchors which will properly support the camera. If necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional support for the camera.
2
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
3
Contents
4
ED910/930 eZ.HD Indoor Dome Camera
1. Introduction
Get incredible performance in bright light environments or low light, and the resolution listed in the specification from the actual camera you install. To take full advantage of the amazing resolution available from this advanced imaging technology, the Everfocus eZ.HD Series ED910/930 uses a vari-focal lens together with 1/2.8" SONY 1.37M pixels CMOS to deliver 720p high resolution.
Combined with a useable native low light sensitivity of 0.08 lux without using digital slow shutter.
The camera truly provides HD images without compromising its 720p video quality, Digital Wide
Dynamic Range for clear color images in the most challenging of bright or unbalanced scene lighting conditions. Moreover, the ED930 features 18 LEDs with range of 30m / 100 feet; it also provides true day/night enhanced images in low light environments with guaranteed ZERO ghosting. The cameras are equipped with 3-axis rotation design, allowing wall or ceiling mounting. Your choice of vari-focal 2.8~12mm DC iris lens for easily adjustable field of view; dual voltage operation and a full suite of OSD Menu and DSP functions controllable at the camera (3DNR to save DVR HDD space, privacy masking, mirroring, and much more) This is the camera that you have been waiting for to create analog CCTV systems that produce astounding image clarity in a wide range of indoor applications at the widest range of light levels. The ED910/930 supports both NTSC and PAL scanning systems, which can be switched via OSD.
Model
ED910
Image Sensor
1/2.8" SONY 1.37M pixels
CMOS
ED930
1.1 Packing List
Resolution IR LEDs
No
720p
Yes (18 LEDs)
Day / Night
True Day/Night
Dome Camera x 1
User Manual x 1
Test Lead x 1
DC Power Pigtail Cable x 1
Quick Installation Guide x 1
Screw x 3
Screw Driver x 1
Plastic Anchor x 3
Template Plate x 1
5
ED910/930 eZ.HD Indoor Dome Camera
1.2 Features
720p with high flexibility and performance for astounding image
1/2.8" SONY 1.37M pixels CMOS, delivers amazing high sensitivity
Vari-focal 2.8~12mm DC iris lens to capture the desired field of view
18 IR LEDs for 30m/100ft. range -depending on scene IR reflectivity (for ED930)
D-WDR to improve the visibility under high contrast scene
Provides 3D Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio
images even under low light environments
Support 720p & 960H analog signal output, which can be easily switched by OSD
Easy lock installation by screwing the base plate to the surface and then locking the camera to the base plate without mounting screws
2. Cable Description
No. Name
1 Power Cable
2
3
Dual Video Output
Test Lead
4 DC Power Pigtail Cable
Descriptions
Connect to a 12VDC or 24VAC power source.
720p and 960H output, using a 75 Ohm BNC-type coaxial cable.
Connect to a monitor for setting image aim and focus.
Optional power pigtail cable. The red wire is positive (+); while the black wire is negative (-).
6
ED910/930 eZ.HD Indoor Dome Camera
3. Installation
3.1 Installation and Adjustment
ED910 without LED ED930 with LED
Camera Breakdown
7
ED910/930 eZ.HD Indoor Dome Camera
Important Notice
Please be noted the camera Base Plate may loosen when you take out the camera from the pack. It is because the Base Plate is attached to the Camera Body without locking tightly in order to simplify the installation procedure.
Camera Body Base Plate
The Base Plate is unlocked to the Camera Body.
1. Stick the Template Plate on the position where you want to attach the camera, drill the three holes on the Template Plate for screwing the camera with the supplied Screws and
Anchors, and the circle in the middle only if you want to wire the cables through the wall
/ ceiling (the “Line out” mark represents the factory wiring position).
2. Insert the supplied three Anchors into the holes.
8
ED910/930 eZ.HD Indoor Dome Camera
3. Rotate counter-clockwise to remove the camera cap, press and pull to remove the line r.
Remark: Hold the liner with one hand, press and pull to remove the liner (refer to the “arrow”
label which marked to the liner)
4. Push the inner click outward and rotate the base plate counter-clockwise, then remove the camera body from the base plate. (See the yellow arrow label on the camera)
9
ED910/930 eZ.HD Indoor Dome Camera
5. Screw the base plate to the wall / ceiling using the supplied three screws. Note that if you want to wire the cables through the wall / ceiling, break the middle part of the base plate.
6. Lock the camera body back to the base plate, align the arrow marks and rotate the camera body clockwise. A “click” sound should be heard when the camera body and the base plate are firmly locked. (See the direction arrow labels on the camera)
10
ED910/930 eZ.HD Indoor Dome Camera
7. Connect the camera to the 12 VDC or 24 VAC power source and an AHD DVR or a monitor.
8. Optionally connect the camera to a monitor using the supplied Test Lead for adjusting camera angles, focus, zoom and configuring OSD menu a. Connect one end of the Test Lead to the camera and the other end to a monitor. b. To adjust camera angles, simply tilt, pan or rotate the camera.
11
ED910/930 eZ.HD Indoor Dome Camera c. To configure the OSD Menu, using the function button.
Note: The function button is not only for direction control, also for switching Video format and Video output. Please follow the detailed instruction as below:
Press the "DOWN" button key over 5s to switch video format from PAL to NTSC.
Press the "LEFT" button key over 5s to switch video output from 720p to 960H
(720p is the default).
Press the "RIGHT" button key over 5s to switch video output from 960H to 720p. d. To adjust the Zoom / Focus, using the Zoom / Focus screws. Tighten the zoom /Focus
screws using the supplied Screw Driver.
9. Put the liner back and secure the camera cover cap back to the camera.
12
ED910/930 eZ.HD Indoor Dome Camera
4. Configuration in the OSD Menu
You can use the function buttons on the rear panel of the camera body to configure camera settings in the OSD menu:
No. Main Sub Menu Sub Menu / Function
1 Lens
2 Exposure
3 Backlight
Indoor*
DC*
Mode
Outdoor
Min Shu.
Max. Shu.
NTSC: 1/30*
PAL: 1/25*
NTSC: 1/60,FLK,1/240,
1/480,1/1000,
1/2000,1/5000*,
1/10000, 1/50000
PAL: 1/50,FLK,1/200,
1/400,1/1000,
1/2000,1/5000*,
1/10000, 1/50000
BLC
Iris Speed 0 – 15(0*)
Manual
Shutter
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
AGC 0 – 15(15*)
Off*
Sens-up
Auto
Brightness 1-100(40*)
Sens-up X2, X4*, X6, X8, X10, X15, X20, X25, X30
D-WDR
Off*
On Level 0-8(8*)
Auto
Off*
Defog
Auto
Pos/Size Position, Size,↑,↓,→,←
Gradation 0-2(0*)
Default
Off*
Level
Area
Middle*, High, Low
Position, Size,↑,↓,→,←
13
ED910/930 eZ.HD Indoor Dome Camera
4
5
6
7
White
Balance
Day &
Night
NR
Special
Default
Select
Display
Area1*, Area2, Area3, Area4
Off
On* Position, Size,↑,↓,→,←
On*/Off
HSBLC
Black
Mask
Level
Model
0-100(20*)
All Day*
Night AGC Level 0-255(48*)
Default
ATW*
AWC→SET
Indoor
Outdoor
Manual
Blue
Red
AWB
Ext
(Ext* for ED930)
1-500(50*)
0-100(50*)
Auto
(Auto* for ED910)
D→N(Delay)
N→D(Delay)
D→N(AGC)
D→N(Delay)
N→D(AGC)
N→D(Delay)
0-60(1*)
0-60(1*)
1-255(240*)
0-60(1*)
1-255(50*)
0-60(5*)
Color
B/W
2DNR
3DNR
Cam Title
D-effect
Burst
IR Smart
IR PWM
Off
0-100(100*)
Middle*/Low/Off/High
Middle*/Low/Off/High
Off*
On
Freeze
Mirror
Off*/On
Off( Off* for ED910)
On
(On* for
ED930)
Level
Area
0-15(4*)
Position, Size,↑,↓,
→,←
0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶→←
↑↓()ˉ-_▊/=&:~,.
Off*/On
Off*, Mirror, V-flip, Rotate
14
ED910/930 eZ.HD Indoor Dome Camera
Neg.
Image
Off*
Off*/On
Motion
On
Select
Display
Area1*,Area2,Area3,Area4
On* Position, Size,↑,↓,→,←
Off
Sensitivity 0-100(64*)
Color Green*, Blue, White, Red
Trans
1.00*,0.75,0.50,
0.25
View Type Off, Block, Outline, All*
Alarm
OSD View On*/Off
Alarm Out On*/Off
Alarm Sig High*, Low
Time 1-15(3*)
Default
Off
Privacy
On
Select
Display
Color
Trans
Area1*,Area2,Area3,Area4
Off
Color*
Mosaic
Position, Size,↑,↓,→,←
Position, Size,↑,↓,→,←
Inv Position, Size,↑,↓,→,←
White*, Black, Red, Blue, CYAN, Yellow,
Green
1.00*,0.75,0.50,
0.25
Default
Language ENG*/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR
Off
Live DPC
On*
AGC level 0-255(65*)
Level 0-100(100*)
Off
Defect
White DPC
On*
Pos/Size
Start
Position, Size,↑,↓,→,←
Close the iris then press
DPC View Off*/On
Level 0-60(5*)
AGC 0-14(14*)
15
9 Exit
ED910/930 eZ.HD Indoor Dome Camera
8 Adjust
RS485
Sharpness
CRT/LCD
Off*
Black DPC
On
Pos/Siz
Start
Position, Size,↑,↓,→,←
Press Enter
DPC View Off*/On
Level 0-255(255*)
CAM ID 0-255(1*)
ID Display Off*/On
Baud Rate 2400,4800,9600,19200 ,38400
Off
Level 0-10(6*)
Auto* Start AGC
End AGC
0-255(50*)
0-255(200*)
CRT
LCD*
Black Level
Blue Gain
Red Gain
Gamma
Blue Gain
Red Gain
Sens-up x2*, x4, x6, x8,x10, x15, x20, x25, x30
0-60(0*)
0-100(50*)
0-255(50*)
User*,0.45,0.50,0.55,0.60,
0.65,0.70,0.75,0.80,0.85,0.
90,
0.95,1.00
0-100(50*)
0-100(50*)
LSC Off*/On
Video. Out PAL/NTSC
Save& END /Reset/Not Saved
16
ED910/930 eZ.HD Indoor Dome Camera
5. Specifications
P/N
Pickup Device
Video Format
Effective Pixels
Scanning System
Sensitivity
S/N Ratio
Electronic Shutter
Video Output
Gamma Correction
Lens Type
BLC
ED910
1/2.8" SONY 1.37M pixels CMOS
NTSC and PAL( can be switched via OSD)
1280 (H)*720 (V)
Progressive Scan
0.08 Lux
ED930
0 Lux with IR on
Over 50 dB (AGC OFF)
AUTO, Manual (X30~1/ 50000), FLK
BNC 1.0Vp-p 75Ω
0.45
2.8-12mm DC Iris
OFF/BLC/HS BLC Selectable
AGC
White Balance
Sync Mode
Day/Night
IR LED
IR Distance
0~15 Levels
ATW/AWC-SET/INDOOR/OUTDOOR/MANUAL/AWB
Internal
Ext, Auto, Color, B/W, True D/N with ICR，Auto
N/A
N/A
18 Units
Up to 30m/100ft. range(depending on scene IR reflectivity)
12-Language OSD Languages
Digital Noise Reduction 2DNR/3DNR, Off
Defog Off/Auto(under B/W mode)
D-WDR On/Off
Sens-up
Mirror
Motion Detection
Privacy Mask
Environmental
Off/On for 4 selectable zones
Indoor
Power Source
Power Consumption
12VDC/24VAC
12VDC:1.6w max./ 24VAC:
1.7w max.
Operating Temperature -10°C~50°C / 14°F~122°F
Humidity
Dimensions(in/mm)
20%~80%
133 x 96mm / 5.24 " x 3.78"
Weight(lbs/g)
Certifications
Off/On(x30~x2)
Horizontal/Vertical/HV
Off/On for 4 selectable zones (On screen indication on alarm)
0.65lbs /295g
CE/FCC/RoHS
12VDC:3.7w max./ 24VAC: 3.5w max.
0.79lbs /360g
Specifications and designs are subject to change for improving the functionality of this product without notice.
17
ED910/930 eZ.HD Indoor Dome Camera
EverFocus Electronics Corp.
EverFocus Taiwan:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 3943 www.everfocus.com.tw [email protected]
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495 www.everfocus.de [email protected]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423 www.everfocus.com.cn [email protected]
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337 www.everfocus.com.cn [email protected]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838 www.everfocus.com [email protected]
EverFocus Japan:
3F Kuramochi, Buildingll 2-2-3 Koto-Bashi,
Sumida-Ku Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189 www.everfocus.co.jp [email protected]
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 631 436 5070
FAX: +1 631 436 5027 www.everfocus.com [email protected]
EverFocus China - Shanghai:
Room 403, Ruijin Business Center, No.96, Zhaojiabang
Road, Luwan district, Shanghai 200020, China
TEL: +86 21 6471 2229 / 6471 2291
FAX: +86 21 6471 0566 www.everfocus.com.cn [email protected]
EverFocus India:
UBS, 629/1243, 1st Floor, G Block, Behind
Teacher’s Colony, Bandra Kurla Complex,
Bandra (E), Mumbai 400 051, India
TEL: +91 22 6726 4500
FAX: +91 22 6726 4518 www.everfocus.in [email protected]
Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed ofseparately from your household waste.
Please, dispose of this equipment at your local community waste collection/recycling centre.
In the European Union there are separate collection systems for used electrical and electronic product.
Please, help us to conserve the environment we live in!
Ihr EverFocus Produkt wurde entwickelt und hergestellt mit qualitativ hochwertigen Materialien und Komponenten, die recycelt und wieder verwendet werden können.
Dieses Symbol bedeutet, dass elektrische und elektronische Geräte am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu erhalten, in der wir leben!
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement