Westinghouse EU24H1G1 Installation guide

Contents
Safety and warnings.......................................................................................2-3
Introduction.....................................................................................................4
Stand installation guide.....................................................................................5
Installation................................................................................................... 6-9
Remote Control..............................................................................................10
Power Connection......................................................................................11-14
Setup Menus..............................................................................................15-39
-1-
SAFETY AND WARNINGS
The symbol indicates that dangerous
voltages constituting a risk of electric shock
are present within this unit.
The symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this Television near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, install in
accordance with the instructions.
8) Do not install near any heat sources such as
radiations, heat registers, stoves, or other Television
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
plug. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protected the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
Television.
11) Only use attachments/accessories specified by
the manufacturer.
12) Unplug this Television during lighting storms or
when unused for long periods of time.
13) Refer all servicing to qualified service personnel.
Servicing is required when the Television has been
damaged in any way, such as; power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the Television, the Television has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
14) Mains plug is used as the disconnect device, the
disconnect device shall remain readily operable.
15) The ventilation should not be impeded by
covering the ventilation openings with items, such as
newspapers, table-cloth, curtains, etc.
16) No naked flame sources, such as lighted candles,
should be placed on the Television.
17) Attention should be drawn to the environmental
aspects of battery disposal.
18) The use of Television in moderate climate.
19) The Television shall not be exposed to dripping
or splashing and that no objects filled with liquids,
such as vases, shall be placed on the Television.
WARNING:
To reduce the risk of fire or electric shock, do
not expose this Television to rain or moisture.
WARNING:
The batteries shall not be exposed to
excessive heat such as sunshine, fire or the
like.
WARNING:
The excessive sound pressure from earphones
and headphones can cause hearing loss.
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user
accessible parts. When servicing use
only identical replacement parts.
This marking indicates that this product
should not be disposed with other
household wastes throughout the EU.
To prevent possible harm to the
environment or human health from
uncontrolled waste disposal, recycle it
responsibly to promote the sustainable
reuse of material resources. To return
your used device, please use the return
and collection systems or contact the
retailer where the product was
purchased. They can take this product
for environmental safe recycling.
This Westinghouse product has earned the
ENERGY STAR® for meeting U.S. Federal
energy efficiency guidelines as set by the
Department of Energy and Environmental
Protection agency. The ENERGY STAR®
program exists to provide energy saving
guidelines and help promote energy efficient
products and practices. Changes to certain
features, settings and functions of this TV can
change and/or increase its power consumption.
Depending on how settings are changed, power
consumption may exceed the limits required
for ENERGY STAR® qualification.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN!
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
-2-
SAFETY AND WARNINGS
High voltages are used in the operation of this television
receiver. Do not open the cabinet.
Refer servicing to qualified service personnel.
Never stand on, lean on, or suddenly push the television or
its stand. You should pay special attention to children.
Serious injury may result if it falls.
To prevent fire or electrical shock hazard, do not expose
the television receiver to rain or moisture.
Do not place your television on an unstable cart, stand,
shelf or table. Serious injury to an individual and/or damage
to the television may result if it falls.
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
When the television receiver is not used for an
extended period of time, it is advisable to disconnect
the AC power cord from the AC outlet.
Do not block the ventilation holes on the back cover of the TV.
Adequate ventilation is essential to prevent failure of
electrical components.
Avoid exposing the television receiver to direct sunlight
and other sources of heat. Do not stand the television
receiver directly on other products which give off heat,
e.g. video cassette players and audio amplifiers. Do not
place naked flame sources, such as lighted candles on
or near the television.
Dim:515*320mm(不包括底座)
Do not trap the power supply cord under the television
receiver's stand.
If the television is to be built into a compartment or similar
enclosure, the minimum distances must be maintained. Heat
build-up can reduce the life of your television, and can also
be dangerous.
-3-
INTRODUCTION
Main features
Accessories
Integrated ATSC TV tuner for HDTV broadcast reception
High brightness provides a vivid and brilliant picture
Deeper blacks and brighter whites with high contrast
■ Wide Screen aspect ratio (16:9) for a complete home
theater experience
■ HDMI input for true digital connection
■ VGA port for connection to PC
■ Built-in stereo speaker system
■ Full-function Remote Control
Power cable...................................
1
Infrared Remote Control....................
1
■
■
■
User’
s M anual .................................
1
Battery(AAA)...................................
2
Main parameter
Viewing Picture Size (diagonal)
24 inches
Resolution:
1366 x 768
Power supply
AC 100-240V 50/60Hz
Power consumption
40W
Audio Output Power (THD
7%):
2x3W
Aspect Ratio:
16:9
TV System:
ATSC Digital system and NTSC Analog system
Video Signal System:
NTSC
Receiving Channel:
Cable :1-135/ Air: 2-69 (ATV&DTV)
High-Definition Multimedia Interface (HDMI) Input
x2
YCb(Pb)Cr(Pr) Input
x1
Composite Video Input
x1
Analog RGB (VGA) Input
x1
Audio Input
x2
Headphone Output
x1
SPDIF Output
x1
Horizontal definition (TV line)
Composite Video Input >=350
Video Input
>=400
YCb(Pb)Cr(Pr)
>=400
-4-
Base Stand Assembly Instruction
1. Place the TV with the display side down on a flat surface. Use a cloth to protect the display.
Position the stand base plate onto the bottom of the stand pole.
2. Attach the stand base plate to the stand pole by firmly tightening the supplied screw.
-5-
INSTALLATION
Side panel
Front panel
3
SOURCE
1
MENU
2
CH+
3
CH-
1
VOL+
STANDBY
30
1:
Remote control sensor.
2:
Indicator LED: BLUE
5
30
1. SOURCE: Display the input source menu.
2. MENU: Display main MENU.
3. CH+/CH-: In TV mode, press "CH+" or "CH-" to
change the channel up and down. In MENU mode, press
"CH+" or "CH-" to select items in standby mode, press
"CH+" or "CH-" to turn on the TV.
4. VOL+/VOL-: Adjust sound level. In MENU mode,
press "VOL+ " or "VOL- " to adjust the item that you
selected.
5. STANDBY: Press this button to turn the unit ON
from STANDBY mode. Press it again to turn the set
back to STANDBY.
POWER ON.
RED
4
VOL-
2
STANDBY.
3: Side panel keys
REAR Connections
Y
Pb
Pr
VIDEO
L
R
SPDIF
All the terminals are (from left to right):
YPbPr INPUT,VIDEO, AUDIO INPUT, SPDIF OUTPUT.
Note: AV and YPbPr share one audio channel.
SIDE Connections
All the terminals are (from left to right):
USB, HDMI2, HDMI1, HEADPHONE, PC AUDIO, VGA, RF.
Note: 1. When HDMI has an input signal coming from a DVI source then the audio input signal must be
connected to the PC audio input.
2. The USB port can be used for JPEG Images, Motion-JPEG videos, or upgrading software.
-6-
INSTALLATION
ANTENNA
Note:
Aerial connections: IEC (female).
Input impendance:75 unbalanced.
PC
STEPS:
Be sure both the TV and computer are set to
Power off.
1.Connect VGA and audio cable.
2.Connect the power cord.
3.Power on the TV, switch to PC mode.
4.Power on the PC.
This sequence is very important.
-7-
INSTALLATION
PC
PRESET MODE
RESOLUTION
V.Freq.(Hz)
H.Freq.(KHz)
1
720*400
70
31.47
2
640*480
60
31.47
3
640*480
75
37.50
4
800*600
60
37.88
5
800*600
75
46.88
6
1024*768
60
48.36
7
1024*768
70
56.48
8
1024*768
75
60.02
9
1280*1024
60
63.98
10
1280*1024
75
80.00
11
1366*768
60
75.50
-8-
INSTALLATION
AV EQUIPMENT
You can use the input terminals on TV set rear as follows.
HDMI
Y Yellow (video)
W White(audio L)
R Red(audio R or Pr)
B Blue(Pb)
VIDEO EQUIPMENT with YPbPr
G
B
R
G Green(Y)
W
R
G
B
R
Y
Pb
Pr
VIDEO
L
R
W
W
R
SPDIF
R
VIDEO EQUIPMENT
W
R
TO VIDEO
OUTPUTS
TO AUDIO OUTPUTS
The television's inputs can be connected to the following types of equipment: VCR, multi disc player,
DVD, camcorder, video game or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i.
-9-
REMOTE CONTROL
1: POWER
To turn the TV on.
2: NUMBER KEY
For direct access to channels .
3:
Displays the main on-screen menu.
4: CURSOR
To move within the menu.
5: EXIT
To exit the menu.
6: VOL+/To adjust sound level.
7: P.M
To switch picture mode.
8:
Press to display and select the available video sources.
9: MUTE
To disable or enable the sound.
10: RECALL
To access the previously viewed channel.
11: ENTER
Confirms selection.
12: TV DISPLAY
Displays/removes the program information
13: S.M
To switch sound mode.
14: CH+/CHTo access the next or previous channel.
15: ASPECT
To change picture aspect .
16: CH LIST
To display the channel list.
17: EPG
To display all the information of DTV programs.
18: FAV
To circle access your favorite channels in digital TV mode.
19: HDMI
Hot key to go directly to HDMI source.
20: AV
Hot key to go directly to AV source.
21: DTV STRENGTH
To display the DTV signal strength menu.
22: TV
Hot key to go directly to TV source.
23: YPbPr
Hot key to go directly to YPbPr source.
24: CC
To enable or disable the CC function.
25: VGA
Hot key to go directly to VGA source.
26: MTS
To switch the sound stereo.
27: COLOR KEYS
To access or save a favorite channel.
-10-
POWER CONNECTION
Select Language
Welcome to the Westinghouse HDTV
Setup Wizard.
Follow this guide to help setup your HDTV
for scanning channels or accessing your
external devices for cable, satellite, Bulray, DVD,and gamming.
English
French
Spanish
Use the ▼▲ arrows on your remote
control to select the language to use for
menus and message screens.
▼▲ :Select
ENTER : Confirm
Power On Mode
Use the ▼▲ arrows on your remote
control to select power on mode.
Home optimizes the video settings for Energy
Star qualification.
Retail optimizes the video setting for use on a
retail showroom floor or demo environment.
Home
Retail
Go Back
▼▲◀▶ :Select
ENTER : Confirm
Let’s Get Connected...
Click here to connect a Cable Box or Satellite Box
Click here to connect a Game, Blu-Ray,DVD,or other player
Click here to scan channels from the Antenna or coaxial cable input
Go Back
▼▲ :Select
ENTER : Confirm
-11-
POWER CONNECTION
Scan Channels from the Antenna or coaxial cable input
Use the ▼▲ arrows on your remote control to
select the channel scan type.
Antenna(ATSC)
Cable
Go Back
▼▲◀▶ :Select
ENTER : Confirm
Antenna[ATSC] Channel Access
Antenna users need a Channel Access Code in order to
perform a channel scan and receive broadcast signals.
Contact Westinghouse’s Channel Access Service by:
Web:www.westinghousedigital.com/support;
select Channel Access and enter Access Info
Text Message: Text Tuner to 95495
Phone: 1-800-701-0680 follow instructions
Select Next to obtain the Access code.
Go Back
◀▶ :Select
Next
ENTER : Confirm
Antenna[ATSC] Channel Access Information
To access channel scan you will need the following Access
Information:
Model: LD-3237
Serial NO.: xxxxxxxxxxxxx
Channel Scan Type: ATSC
Provide these items to Westinghouse’s Channel Access Service
by web,text,or phone to obtain an Access Code,then select Next
to input access code.
Go Back
◀▶ :Select
Next
ENTER : Confirm
Enter Channel Access Code
Using your remote control to enter the 5 digit access code
provided by the channel access service.
Go Back
0-9: Key in password
ENTER : Confirm
Scanning Channels
Progress Bar
Channels Found
Analog:
0
Digital:
0
Signal
Menu: Exit Scan
-12-
POWER CONNECTION
Select Language
Welcome to the Westinghouse HDTV
Setup Wizard.
Follow this guide to help setup your HDTV
for scanning channels or accessing your
external devices for cable, satellite, Bulray, DVD,and gamming.
English
French
Spanish
Use the ▼▲ arrows on your remote
control to select the language to use for
menus and message screens.
▼▲ :Select
ENTER : Confirm
Power On Mode
Use the ▼▲ arrows on your remote
control to select power on mode.
Home optimizes the video settings for Energy
Star qualification.
Home
Retail
Retail optimizes the video setting for use on a
retail showroom floor or demo environment.
Go Back
▼▲◀▶ :Select
ENTER : Confirm
Let’s Get Connected...
Click here to connect a Cable Box or Satellite Box
Click here to connect a Game, Blu-Ray,DVD,or other player
Click here to scan channels from the Antenna or coaxial cable input
Go Back
▼▲ :Select
ENTER : Confirm
Cable or Satellite Source Input
Use the ▼▲ arrows on your remote control to select the
input connected to the set top box?
For optimal video quality,we recommend HDMI or Component
(refer to Quick Connect Guide or User Manual to help you
determine what connection you are using).
HDMI 1
HDMI 2
Component
Composite
Antenna
Go Back
▼▲◀▶ :Select
ENTER : Confirm
-13-
POWER CONNECTION
Select Language
Welcome to the Westinghouse HDTV
Setup Wizard.
Follow this guide to help setup your HDTV
for scanning channels or accessing your
external devices for cable, satellite, Bulray, DVD,and gamming.
English
French
Spanish
Use the ▼▲ arrows on your remote
control to select the language to use for
menus and message screens.
▼▲ :Select
ENTER : Confirm
Power On Mode
Use the ▼▲ arrows on your remote
control to select power on mode.
Home optimizes the video settings for Energy
Star qualification.
Retail optimizes the video setting for use on a
retail showroom floor or demo environment.
Home
Retail
Go Back
▼▲◀▶ :Select
ENTER : Confirm
Let’s Get Connected...
Click here to connect a Cable Box or Satellite Box
Click here to connect a Game, Blu-Ray,DVD,or other player
Click here to scan channels from the Antenna or coaxial cable input
Go Back
▼▲ :Select
ENTER : Confirm
Source List
Composite
HDMI 1
HDMI 2
VGA
Component
Go Back
▼▲◀▶ :Select
USB
ENTER : Confirm
-14-
SETUP MENUS
SOURCE
MENU
CH+
CHVOL+
VOLSTANDBY
then ENTER
ENTER
-15-
SETUP MENUS
ENTER.
ENTER.
-16-
SETUP MENUS
ENTER.
Energy Saving
Retail
Movie
User
Energy Saving: Uses low brightness display only for energy
saving mode.
Retail: Uses high contrast display for clear-cut images ideal for viewing
demo events.
Movie: Images are displayed as accurately near it’s original recording
condition.
User: Uses the customized settings.
-17-
SETUP MENUS
ENTER.
ENTER.
-18-
SETUP MENUS
ENTER.
ENTER.
-19-
SETUP MENUS
ENTER.
ENTER.
-20-
SETUP MENUS
ENTER.
ENTER.
-21-
SETUP MENUS
ENTER.
-22-
SETUP MENUS
ENTER.
-23-
SETUP MENUS
ENTER
-24-
SETUP MENUS
-25-
SETUP MENUS
ENTER
ENTER
-26-
SETUP MENUS
ENTER
ENTER
ENTER
-27-
SETUP MENUS
ENTER.
-28-
SETUP MENUS
ENTER
ENTER
-29-
SETUP MENUS
Size
-30-
SETUP MENUS
ENTER.
Parental Control
-31-
SETUP MENUS
ENTER.
-32-
SETUP MENUS
ENTER.
ENTER
-33-
SETUP MENUS
ENTER.
ENTER
ENTER.
-34-
SETUP MENUS
ENTER
Régie du
Cinéma du Québec
ENTER.
ENTER
-35-
SETUP MENUS
ENTER.
ENTER
ENTER.
ENTER.
ENTER.
ENTER.
-36-
SETUP MENUS
ENTER.
ENTER.
-37-
SETUP MENUS
ENTER.
-38-
SETUP MENUS
Multimedia MENU
If you select the USB source, you can use the Multimedia Menu to display
JPEG pictures and play motion-JPEG files.
1.Photo
If you select the Photo Icon and enter the JPEG folder,then play a JPEG
file, the screen display the Menu as below:
Use ◀/▶to select the function Icon and use the ENTER key to active the related
function. Press EXIT key to goto previous menu.
2 . Movie
If you select the Movie Icon and enter the Motion-JPEG folder,then play a
Motion-JPEG file, the screen display the Menu as below:
00:02:04/00:02:07
Use ◀/▶to select the function Icon and use the ENTER key to active the related
function. Press EXIT key to goto previous menu.
-39-