Utopia/Paradise Series
Pre-Delivery Instructions
Please take the time to read this booklet carefully, as it will provide you with the information you will need to ensure
the safe, secure, and timely installation of your new spa. The following sections are guidelines on how to prepare for
delivery and set-up of your new spa. Specifically covered are site selection, delivery access, ground preparation, and
electrical requirements.
Remember to carefully read the Owner’s Manual that accompanies your spa and to complete the warranty card
within ten days of delivery. These items, along with other valuable information, are included in the Owner’s Packet
which can be located in the equipment compartment of your spa. You will also find your serial number in the
equipment compartment.
Watkins Manufacturing Corporation reserves the right to change features, specifications, and design without
notification and without incurring any obligation.
DATE PURCHASED: __________________________________________________________________
DATE INSTALLED:____________________________________________________________________
DEALER:____________________________________________________________________________
ADDRESS:___________________________________________________________________________
TELEPHONE:________________________________________________________________________
In most cities and counties, permits will be required for the installation of electrical circuits or the construction of
exterior surfaces (decks and spa enclosures). In addition, some communities have adopted residential barrier codes
which may require fencing and/or self-closing gates on the property to prevent unsupervised access to a pool (or
spa) by children under 5 years of age. Your Caldera® spa is equipped with a locking cover that meets the ASTM
F1346-91 Standard for Safety Covers, and as a result, is usually exempt from most barrier requirements. As a
general practice, your local Building Department will inform you of any applicable barrier requirements at the time
a permit is obtained for the installation of an electrical circuit. Your Caldera dealer can provide information on which
permits may be required.
Pre-Delivery Instructions
SITE SELECTION AND PREPARATION
IMPORTANT: Site selection and preparation are your responsibility. Carefully read these instructions and consult
your authorized Caldera® dealer if you have any questions.
You probably have a spot picked out for your new spa, whether it’s indoors or outdoors, on a patio or on a deck. Just
make sure you check the following:
•
Always put your spa on a structurally sound, level surface. A filled spa can weigh a great deal. Make
certain that the location you choose can support the weight of your filled spa.
•
Don’t forget to level your spa. (See the Ground and Spa Leveling Preparation section on the next page.)
•
Locate your equipment compartment, which houses all of the electrical components, in a place where
water will drain away from it. Allowing water into the equipment compartment can damage the electronics,
or may result in tripping your house’s circuit breaker.
•
Leave yourself easy access to the circuit breakers in the subpanel.
•
Never let water get into the subpanel. Your 230 volt spa’s subpanel is raintight when installed correctly
with the door closed.
•
Leave access to the entire front of the spa (the removable panel provides access to the spa’s equipment)
for periodic spa care and maintenance.
Note that on the Utopia spas, the SpaGlo® exterior lighting fixtures are located on only three sides. The side
opposite the main control panel has no lighting.
INDOOR/BASEMENT INSTALLATION
Be aware of some special requirements if you place your spa indoors. Water will accumulate around the spa, so
flooring materials must provide a good grip when wet. Proper drainage is essential to prevent a build-up of water
around the spa. When building a new room for the spa, it is recommended that a floor drain be installed. The
humidity will naturally increase with the spa installed. Water may get into woodwork and produce dry rot, mildew, or
other problems. Check for airborne moisture’s effects on exposed wood, paper, etc. in the room. To minimize these
effects, it is best to provide plenty of ventilation to the spa area. An architect can help to determine if more ventilation
must be installed.
Caldera spas are equipped with a jet pump shroud to remove excessive heat from the equipment compartment.
Find this vent, and be sure it is not blocked by anything, including carpeting.
Your Caldera dealer can help you with local information such as zoning regulations and building codes.
DECK INSTALLATION
To be certain your deck can support your spa, you must know the deck’s maximum load capacity. Consult a
qualified building contractor or structural engineer before you place the spa on an elevated deck or indoors. To find
the weight of your spa, its contents and occupants, refer to the Spa Specification chart (on back cover). This weight
per square foot must not exceed the structure’s rated capacity, or serious structural damage could result.
OUTDOOR AND PATIO INSTALLATION
No matter where you install your new spa, it’s important that you have a solid foundation to support it. Structural
damage to the spa resulting from incorrect installation or placement on an inadequate foundation is not covered
under the spa’s limited warranty. (See next page for specifics)
GROUND AND SPA LEVELING PREPARATION
Your Caldera spa has been engineered to perform on several types of common yard surfaces. While a concrete
slab is best for long-term use*, other foundations are acceptable as long as a level base is prepared prior to delivery.
Three foundation base pictures, shown at right, represent examples of alternatives to a concrete slab for spas
installed without gazebos or other accessories.
Page 2
*NOTE: A reinforced concrete pad at least four inches thick or structurally sound deck able to support the “dead
weight” found in the spa specification chart is required for the Cantabria®,
Geneva®, Niagara® spas, and recommended for the Tahitian®, Makena™
FOUNDATIONS FOR SPAS ONLY
(No gazebo)
Salina®, Martinique® and Kauai® spas. The reinforcing rod or mesh in
the pad should be attached to a bond wire.
•
Concrete sloped at 1/2 inch per 10 feet is preferred so that
rain water and water spillover will run off and not puddle
underneath the spa (water under the spa for long periods of
time may cause the wood to deteriorate).
•
If stepping stones or railroad ties are selected for the spa
foundation, they should be placed and leveled below the
entire spa to maintain even distribution of the spa weight.
•
It is important to note that soft surfaces, even when stepping
stones are used to distribute the weight of the spa as evenly
as possible, will still have a tendency to settle unevenly,
resulting in an unlevel spa.
•
Remember, placing the spa on grass or dirt may increase the
amount of debris which is inadvertently brought into the spa
water on the user’s feet.
If you are purchasing a deck package or a spa enclosure with your spa,
a solid foundation becomes mandatory. Placing them on any surface
other than a single level pad could create problems with their installation.
Pictured at right are a few of the recommended surfaces.
As a homeowner, it is your responsibility to provide a suitable, level
foundation for your spa. Keep in mind that most delivery crews are not
equipped to level and prepare spa sites.
PEA GRAVEL
OR CRUSHED ROCK
RAILROAD TIES
PRE-CAST
STEPPING STONES
FOUNDATIONS FOR SPAS
WITH GAZEBOS
CONCRETE PADS
If you are interested in having a concrete slab, brick surface, or wood
deck installed, your Caldera dealer should be able to suggest a qualified,
licensed contractor.
DELIVERY ACCESS
BRICK SURFACES
First, locate the dimensions of your spa on the chart that is found on the
next page. The dimensions shown are the measurements of the spa in
the vertical position, laid on its side.
WOOD DECKING
Next, contact your dealer to find the height and width added by the
delivery cart which the dealer will use to deliver your new spa. Use
the height of the cart plus the dimension shown as H to determine the
vertical clearance required to pass the spa and cart. Use the width of the
cart, or dimension W, whichever is greater, to determine the maximum width of clearance necessary.
NOTE: It may be necessary to allow for additional over-head clearance if the spa will be rolled up or down an incline
or moved up or down a short flight of stairs.
Use the information in the picture below to determine the requirements for access to your desired location. It may be
necessary to remove a gate, part of a fence, or other movable obstructions in order to roll the spa to its installation
site. About ten percent of the time, a crane is the only way to install the spa by lifting it to its final destination.
If the spa has to be taken off of the cart to go over a wall (either because the entry area is too narrow, the eaves are
too low, the corner is too tight, or the stairway is too steep), a crane will be required. Don’t be alarmed!
Page 3
Pre-Delivery Instructions
The crane has a truck-mounted boom which can fit right in your
driveway. It is run by a licensed and insured operator. For a charge,
the crane operator will lift your spa over walls, buildings, or any other
obstruction and place it as close to the installation site as possible. The
Caldera® spa delivery personnel will supervise the crane delivery and
complete the spa installation. Crane delivery typically takes an average
of 30 minutes to complete.
If your spa delivery requires the use of a crane, you may be required to
pay for its services at the completion of the delivery.
SPA DIMENSIONS
Model
Width
Length
Height
Cantabria
38"
9' 0"
7' 7"
Geneva®
38"
7' 5"
7' 5"
®
Niagara
38"
7' 5"
7' 5"
®
Tahitian
36"
7' 0"
7' 0"
Makena™
36"
7' 5"
7' 5"
36"
7' 5"
7' 5"
Martinique
34"
7' 5"
6' 4"
Kauai
29"
7' 0"
5' 5"
®
Salina
®
®
®
How is your width and height clearance?
BACK YARD
Check all gates
Protruding electric meters
Gas meters
A/C units
Do you have sufficient
overhead clearance?
Check low roof eaves,
overhanging branches,
rain gutters
HOUSE
Is the path clear?
Move away branches, dog
houses, firewood, etc.
If there is a 90 turn, can we
clear it? (The spa will not bend)
No more than 6 consecutive
stairs without a landing
STREET
Page 4
Utopia Cantabria®
NOTE: All dimensions are approximate; measure your spa before making
critical design or pathway decisions.
EXTERNAL SCONCE LIGHT
38”
96.5cm
FRONT VIEW
35.3”
89.5cm
ELECTRICAL
CUTOUT
ELECTRICAL
CUTOUT
6.5”
16.5cm
6.5”
16.5cm
65.6”
166.7cm
SPA DRAIN
AIR VENT
DO NOT BLOCK
AIR VENTS
DO NOT BLOCK
OVERALL
108” (274cm)
PEDESTAL
94” (239cm)
PEDESTAL
77”
(196cm)
OVERALL
BOTTOM VIEW
91”
(231cm)
AIR VENT
AIR VENT
AIR VENT
AIR VENT
DOOR SIDE
NOTE: Watkins Manufacturing Corporation requires that the Cantabria be installed on a minimum 4" thick reinforced
concrete pad or structurally sound deck able to support the “dead weight” found in the spa specification chart.
WARNING: The Cantabria must not be shimmed in any manner.
Page 5
Pre-Delivery Instructions
Utopia Geneva® and Utopia Niagara®
NOTE: All dimensions are approximate; measure your spa before making
critical design or pathway decisions.
EXTERNAL SCONCE LIGHT
38”
(97cm)
35”
(89cm)
FRONT VIEW
6.5”
16.5cm
ELECTRICAL
CUTOUT
(BOTH SIDES)
56.75”
(144cm)
10.5”
(27cm)
SPA DRAIN
AIR VENTS
DO NOT BLOCK
10.5”
(27cm)
2.5” (6.4cm)
5” (13cm)
OVERALL
89” (226cm)
84” (213cm)
PEDESTAL
BOTTOM VIEW
OVERALL
89” (226cm)
84” (213cm)
PEDESTAL
ELECTRICAL
OUTLET
AIR VENTS
AIR VENTS
AIR VENTS
ELECTRICAL
OUTLET
DOOR SIDE
NOTE: Watkins Manufacturing Corporation requires that the Geneva and Niagara be installed on a minimum 4” thick
reinforced concrete pad or structurally sound deck able to support the “dead weight” found in the spa specification chart.
WARNING: The Geneva and Niagara must not be shimmed in any manner.
Page 6
Utopia Tahitian®
NOTE: All dimensions are approximate; measure your spa before making
critical design or pathway decisions.
EXTERNAL SCONCE LIGHT
FRONT VIEW
36”
(91cm)
33”
(84cm)
6.5”
16.5cm
ELECTRICAL
CUTOUT
(BOTH SIDES)
10.5”
(27cm)
SPA DRAIN
50”
(127cm)
AIR VENTS
DO NOT BLOCK
10.5”
(27cm)
2.5” (6.4cm)
OVERALL
84” (213cm)
PEDESTAL
80” (203cm)
OVERALL
BOTTOM VIEW
84”
(213cm)
80”
(203cm)
PEDESTAL
ELECTRICAL
OUTLET
AIR VENT
ELECTRICAL
OUTLET
AIR VENT
DOOR SIDE
NOTE: Watkins Manufacturing Corporation recommends that the Tahitian be installed on a minimum 4” thick reinforced
concrete pad or structurally sound deck able to support the “dead weight” found in the spa specification chart.
WARNING: The Tahitian must not be shimmed in any manner.
Page 7
Pre-Delivery Instructions
Paradise Makena ™ and Salina ™
NOTE: All dimensions are approximate; measure your spa before making
critical design or pathway decisions.
36”
33” (91cm)
(84cm)
FRONT VIEW
6.5”
16.5cm
ELECTRICAL
OUTLET
(BOTH SIDES)
DOOR
DOOR
10.5”
(27cm)
56.75”
(144cm)
SPA DRAIN
DOOR
10.5”
(27cm)
2.5” (6.4cm)
5” (13cm)
AIR VENTS
DO NOT BLOCK
OVERALL
89” (226cm)
PEDESTAL
84” (213cm)
BOTTOM VIEW
OVERALL
89” (226cm)
84” (213cm)
PEDESTAL
ELECTRICAL
OUTLET
AIR VENT
AIR VENT
ELECTRICAL
OUTLET
AIR VENT
DOOR SIDE
NOTE: Watkins Manufacturing Corporation requires that the Makena and Salina be installed on a minimum 4” thick
reinforced concrete pad or structurally sound deck able to support the “dead weight” found in the spa specification
chart.
WARNING: The Makena and Salina must not be shimmed in any manner.
Page 8
Paradise Martinique®
NOTE: All dimensions are approximate; measure your spa before making
critical design or pathway decisions.
34”
(86cm)
31”
(79cm)
FRONT VIEW
6.5”
16.5cm
ELECTRICAL
CUTOUT
64.9” (165cm)
SPA DRAIN
DOOR
AIR VENTS
DO NOT BLOCK
5”
(13cm)
2.5”
(6.4cm)
ELECTRICAL
CUTOUT
OVERALL
76” (193cm)
PEDESTAL
72” (183cm)
OVERALL
89”
(226cm)
BOTTOM VIEW
87”
(221cm)
PEDESTAL
ELECTRICAL
OUTLET
AIR VENT
AIR VENT
ELECTRICAL
OUTLET
DOOR SIDE
NOTE: Watkins Manufacturing Corporation recommends that the Martinique be installed on a minimum 4” thick
reinforced concrete pad or structurally sound deck able to support the “dead weight” found in the spa specification
chart.
WARNING: The Martinique must not be shimmed in any manner.
Page 9
Pre-Delivery Instructions
Paradise Kauai ®
NOTE: All dimensions are approximate; measure your spa before making
critical design or pathway decisions.
29”
(74 cm)
FRONT VIEW
26”
(66 cm)
6.5”
6.5” (16.5cm)
Electrical
Cutout
Spa Drain
DOOR
51.25”
(130cm)
Air Vents
Do Not Block
Electrical
Cutout
OVERALL
84” (213cm)
PEDESTAL
80.375” (204cm)
65”
(165cm)
BOTTOM VIEW
61.25”
(156cm)
DOOR SIDE
NOTE: Watkins Manufacturing Corporation recommends that the Kauai be installed on a minimum 4” thick reinforced
concrete pad or structurally sound deck able to support the “dead weight” found in the spa specification chart.
WARNING: The Kauai must not be shimmed in any manner.
Page 10
ELECTRICAL REQUIREMENTS
To ensure you will have an opportunity to use your spa soon after delivery, it is very important that the required
electrical service has been installed. Unless otherwise stipulated by your dealer, THIS IS YOUR RESPONSIBILITY.
IMPORTANT: All electrical circuits must be installed by a qualified, licensed electrician.
230 VOLT INSTALLATION
Your spa contains a control box designed to operate at 230V, 60Hz. Installation of a 50 amp. dedicated circuit is
recommended. The control box must be hard wired directly to a subpanel protected by a Ground Fault Circuit
Interrupter (GFCI). The subpanel containing GFCI breakers is included with the spa.
IMPORTANT NOTE: All electrical connections to the control box must be accomplished by a qualified electrician in
accordance with the National Electrical Code and in accordance with any local electrical codes in effect at the time
and place of installation.
All electrical connections must be made in accordance with the wiring information contained in this manual and on
the back of the field wiring access panel of the control box. A licensed electrician should install a four-wire electrical
service (two line voltages, one neutral, one ground) from the main electrical service panel to the subpanel. The
equipment pack requires a MINIMUM of 112 volts per line under load.
The grounding conductor must be at least #10 AWG. Your electrician should mount the subpanel in the vicinity of the
spa but it should not be closer than five (5) feet from the spa water edge (NEC 680-38 to 41-A-3).
INSTALLATION NOTE: After the spa has been installed, your electrician can connect the conduit from the subpanel
to the spa’s control box and then complete the wiring connections in the control box.
NOTE: Complete step-by-step Installation and wiring instructions for all models are included in the Owner’s Manual
and with each sub-panel, which can be obtained from your dealer.
WARNING: Removing or bypassing the GFCI breakers in the subpanel at any time will result in an unsafe spa and
will void the warranty.
230 VOLT CONVERTED CANTABRIA (OPTIONAL)
The Utopia Cantabria® requires an additional 20 amp breaker in order to operate the heater at the same time as the
lounge pump #3.
This subpanel requires a 70 amp, single phase, 230 volt, four wire service (two line, one neutral, one ground). The
ground wire must never be less than #10 AWG. Use NEC 250-122 (table) and local codes for more information. A
minimum #6 AWG solid copper bond wire is also required.
NOTE: Complete step-by-step Installation and wiring instructions for the Cantabria are included in the Owner’s
Manual and with each sub-panel, which can be obtained from your dealer.
SEE ABOVE FOR IMPORTANT ELECTRICAL INSTALLATION NOTES.
POWER CONNECTION
To connect power to the spa, refer to “230
VOLT WIRING SCHEMATIC DIAGRAM” and
“POWER CONNECTION ACCESS” illustrations. Then proceed
with the following steps:
When supplying power, remove the screws securing the
equipment door (for Utopia spas, always remove the SpaGlo®
exterior light fixtures and lift the fiber optic cable out of the fixture
base before removing the doors). Lower the panel one inch and
remove the panel to allow access to the input power wiring.
NOTE: The 230V wiring diagram is located on the inside of the
Control Box Cover.
POWER CONNECTION ACCESS
CONTROL BOX
DOOR
230V WIRING ACCESS
OPENINGS ON RIGHT& LEFT HAND SIDE
Page 11
Pre-Delivery Instructions
IMPORTANT: The following must be followed to properly install the equipment compartment door.
•
Place top of door or panel directly below bartop against the frame of the spa. For Utopia spas, first lift the
fiber optic cable out of the way.
•
Push bottom of door or panel against the spa frame.
•
Slide door or panel upward (pushing in on center of door to ensure door clips catch) until screw holes line
up, making sure that the exterior fiber optic light cable will fit into the fixture.
•
Slightly pull on door or panel. If door remains against the spa, then replace the screws.
•
If the door does not lock into position, repeat the previous steps.
WIRING DIAGRAMS
UTOPIA GENEVA®, TAHITIAN ® & NIAGARA®
** Refer to NEC 250-122 (table)
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure the white neutral wire is connected to the load neutral of the 30 amp breaker.
*PROVIDED WITH SPA.
NOTE: ALL WIRING SHOULD BE COPPER.
UTOPIA CANTABRIA®
Power
jumpers
** Refer to NEC 250-122 (table)
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure the white neutral wire is connected to the load neutral of the 30 amp breaker.
*PROVIDED WITH SPA.
Page 12
NOTE: ALL WIRING SHOULD BE COPPER.
OPTIONAL UTOPIA CANTABRIA® (CONVERTED)
Remove jumpers A
from TB-1
** Refer to NEC 250-122 (table)
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure the white neutral wire is connected to the load neutral of the 30 amp breaker.
*PROVIDED WITH SPA.
NOTE: ALL WIRING SHOULD BE COPPER.
PARADISE SERIES
230 Volt Permanently Connected
WARNING!
THE EXACT PHYSICAL LOCATION OF THE TERMINALS ON THE GFCI BREAKER
WILL VARY BETWEEN MANUFACTURERS. CONNECTING THE HOT WIRE TO THE
NEUTRAL TERMINAL WILL CAUSE IRREVERSIBLE DAMAGE TO THE CONTROL BOX.
** Refer to NEC 250-122 (table)
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure the white neutral wire is connected to the load neutral of the 30 amp breaker.
*PROVIDED WITH SPA.
NOTE: ALL WIRING SHOULD BE COPPER.
Page 13
Pre-Delivery Instructions
SERVICES AVAILABLE FROM YOUR CALDERA® SPA DEALER
SERVICE COST
Pre-Delivery site inspection
Deliver spa to installation site
______________
Unwrap spa and haul away packaging material
______________
Set up spa
______________
Fill the spa with water and add FROG® bromine and mineral cartridges
______________
Explain and test the spa’s operation:
•
Lighting
•
•
Set temperature control •
Optional Caldera® Entertainment System
GFCI
•
Heater high limit
Control panel functions
Auxiliary panel functions (Utopia spas only)
Explain the safety features
•
•
______________
General spa operation & maintenance orientation
______________
Water quality and maintenance orientation
______________
Adjust the water’s pH, Total Alkalinity and Calcium Hardness ______________
Sanitize the water
______________
Inspect the spa cover, place on spa, and install cover locks
______________
Review winterizing instructions
______________
Review Owner’s Manual & complete Warranty Card
______________
Follow-up call
______________
In-store spa water analysis
______________
TOTAL COST
______________
ADDITIONAL PRODUCTS AVAILABLE FROM YOUR
CALDERA SPA DEALER
•
Monarch® water and spa care products
•
FROG watercare
• Vanishing Act® Calcium Remover
• Clean Screen® Pre-Filter
•
Replacement Filter Cartridges
•
Ozone Systems
•
Cover Lifters
•
Lighting Systems
•
Upgrade Jet Kits
•
Caldera Entertainment Systems
Page 14
Page 15
Pre-Delivery Instructions
ts
ht
Ele
we
ig
De
ad
Re ctrica
qu
ire l
me
n
ht*
we
ig
ht
Fil
l ed
yw
eig
Dr
Eff
filt ectiv
er
are e
a
He
a
(W ter
a tt
s)
Wa
ca ter
pa
cit
y
Fo
o
dim tprin
t
en
sio
ns
He
igh
t
UTOPIA AND PARADISE SPA SPECIFICATIONS
Utopia
Cantabria®
7'7"
x
9'0"
38"
100
square
feet
4,300
550
gallons
1461
lbs.
7,448
lbs.
130
230 volt, 50 or 70 amp
lbs. per
Single phase GFCI
square
protected circuit
foot
Utopia
Geneva®
7'5"
x
7'5"
38"
100
square
feet
4,300
475
gallons
1,080
lbs.
6,092
lbs.
130
230 volt, 30 or 50 amp
lbs. per
Single phase GFCI
square
protected circuit
foot
Utopia
Niagara®
7'5"
x
7'5"
38"
100
square
feet
4,300
500
gallons
1,084
lbs.
6,479
lbs.
140
230 volt, 30 or 50 amp
lbs. per
Single phase GFCI
square
protected circuit
foot
Utopia
Tahitian®
7'0"
x
7'0"
36"
100
square
feet
4,300
360
gallons
1,002
lbs.
5,054
lbs.
120
230 volt, 30 or 50 amp
lbs. per
Single phase GFCI
square
protected circuit
foot
Paradise
Makena™
7'5"
x
7'5"
36"
75
square
feet
4,300
395
gallons
1,020
lbs.
5,364
lbs.
120
230 volt, 30 or 50 amp
lbs. per
Single phase GFCI
square
protected circuit
foot
Paradise
Salina®
7'5"
x
7'5"
36"
75
square
feet
4,300
420
gallons
1,006
lbs.
5,734
lbs.
125
230 volt, 30 or 50 amp
lbs. per
Single phase GFCI
square
protected circuit
foot
Paradise
Martinique®
7'5"
x
6'4"
34"
50
square
feet
4,300
320
gallons
928
lbs.
4,472
lbs.
115
230 volt, 30 or 50 amp
lbs. per
Single phase GFCI
square
protected circuit
foot
Paradise
Kauai®
7'0"
x
5'5"
29"
50
square
feet
4,300
220
gallons
738
lbs.
3,098
lbs.
100
230 volt, 30 or 50 amp
lbs. per
Single phase GFCI
square
protected circuit
foot
CAUTION: Watkins Manufacturing Corporation suggests a structural engineer or contractor be consulted
before the spa is placed on an elevated deck.
* NOTE: The “Filled weight” and “Dead weight” of the spa includes the weight of the occupants
(assuming an average occupant weight of 175 lbs).
NOTE: For 30 amp conversion contact your local dealer.
WATKINS MANUFACTURING CORPORATION
1280 Park Center Drive
Vista, California 92081
(800) 669-1881 extension 8432
©2013 Watkins Manufacturing Corporation. Caldera, Cantabria, Geneva, Niagara, Tahitian, Aquatic Melodies, Makena, Salina,
Martinique, Kauai, SpaGlo, Monarch, ProLift and The Home Relaxation Specialists are trademarks of Watkins Manufacturing
Corporation. FROG is a registered trademark of King Technology, Inc.
Part #62907 Rev. A (3/13)