Bosch Rotak 32 Instruction manual

OBJ_DOKU-24112-003.fm Page 1 Friday, November 16, 2012 10:14 AM
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
www.bosch-garden.com
Rotak
32
F 016 L70 768 (2012.11) O / 10 XXX
en Original instructions
OBJ_BUCH-1349-003.book Page 2 Friday, November 16, 2012 10:13 AM
2 | English
English
Safety Notes
Warning! Read these instructions carefully, be familiar
with the controls and the proper use of the machine.
Please keep the instructions safe for later use!
Explanation of symbols
General hazard safety alert.
Read instruction manual.
Pay attention that bystanders are not injured
through foreign objects thrown from the machine.
Warning: Keep a safe distance from the machine
when operating.
Caution: Do not touch rotating blades. Sharp
blade(s). Beware of severing toes or fingers.
Switch off and remove plug from mains before adjusting, cleaning or if the cable is entangled and
before leaving the garden product unattended for
any period. Keep the supply flexible cord away
from the cutting blades.
Wait until all machine components have completely stopped before touching them. The blades
continue to rotate after the machine is switched
off, a rotating blade can cause injury.
Do not use the machine in the rain or leave it outdoors when it is raining.
Beware electric shock hazard.
Keep supply flexible cord away from cutting
means.
Operation
 Never allow children or people unfamiliar with these instructions to use the machine. Local regulations may restrict the age of the operator. When not in use store the
machine out of reach of children.
 This machine is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the machine by a person responsible for their safety.
F 016 L70 768 | (16.11.12)
Children should be supervised to ensure that they do not
play with the machine.
 Never mow while people, especially children or pets, are
nearby.
 The operator or user is responsible for accidents or hazards occurring to other people or their property.
 Do not operate the machine when barefoot or wearing
open sandals, always wear substantial footwear and long
trousers.
 Thoroughly inspect the area where the machine is to be
used and remove all stones, sticks, wires, bones and other
foreign objects.
 Before using, always visually inspect to see that the
blades, blade bolts and cutter assembly are not worn or
damaged. Replace worn or damaged blades and bolts in
sets to preserve balance.
 Mow only in daylight or in good artificial light.
 Avoid operating the machine in wet grass, where feasible.
 Walk, never run.
 Never operate the appliance with defective guards or
shields, or without safety devices, for example deflectors
and/or grass catchers in place.
 Working on banks can be dangerous.
– Do not mow excessively steep slopes.
– Always be sure of your footing on slopes or wet grass.
– Mow across the face of slopes – never up and down.
– Exercise extreme caution when changing direction on
slopes.
– Use extreme caution when stepping back or pulling the machine towards you.
– Never mow by pulling the mower towards you.
 Stop the blades if the machine has to be tilted for transportation when crossing surfaces other than grass and when
transporting the machine to and from the area to be
mowed.
 Do not tilt the machine when starting or switching on the
motor, except if the machine has to be tilted for starting in
long grass. In this case, do not tilt it more than absolutely
necessary and tilt only the part which is away from the operator. Always ensure that both hands are in the operating
position before returning the machine to the ground.
 Switch on the motor according to the instructions with feet
well away from rotating parts.
 Do not put hands or feet near or under rotating parts.
 Always stand clear of the discharge zone when operating
the machine.
 Never pick up or carry the machine while the motor is running.
 Keep supply cables and extension cables away from
the blade. The blade can cause damage to the cables and
lead to contact with live parts. Beware electric shock hazard.
Remove the plug from the socket:
– whenever you leave the machine,
Bosch Power Tools
OBJ_BUCH-1349-003.book Page 3 Friday, November 16, 2012 10:13 AM
English | 3
– before clearing a blockage,
– before checking, cleaning or working on the machine,
– after striking a foreign object. Inspect the machine for
damage and make repairs as necessary,
– if the machine starts to vibrate abnormally (check immediately).
Power supply
 The voltage indicated on the rating plate must correspond
to the voltage of the power source.
 We recommend that this equipment is only connected into
a socket which is protected by a circuit-breaker that would
be actuated by a 30 mA residual current.
 Only use or replace power supply cables for this unit which
correspond to the types indicated by the manufacturer.
See the operating instructions for the order no. and types.
 Never touch the mains plug with wet hands.
 Do not run over, crush or pull the power supply cable or extension lead, otherwise it may be damaged. Protect the cable from heat, oil and sharp edges.
 The extension lead must have a cross section in accordance with the operating instructions and be protected
against splashed water. The connection must not be in water.
Always wear gardening gloves when handling or working near
the sharp blades.
Electrical Safety
 Warning! Switch off, remove plug from mains before
adjusting, cleaning or if cable is cut, damaged or entangled.
 The blades continue to rotate for a few seconds after
the machine is switched off.
 Caution – do not touch the rotating blade.
Your machine is double insulated for safety and requires no
earth connection. The operating voltage is 230 V AC, 50 Hz
(for non-EU countries 220 V, 240 V as applicable). Only use
approved extension cables. Contact your Bosch Service Centre for details.
Extension cords/leads should only be used if they comply
with H05VV-F, H05RN-F types or IEC type design (60227
IEC 53, 60245 IEC 57).
If you want to use an extension cable when operating your
product, only the following cable dimensions should be used:
– 1.0 mm2: max. length 40 m
– 1.5 mm2: max. length 60 m
– 2.5 mm2: max. length 100 m
Note: If an extension cable is used it must be earthed and connected through the plug to the earth cable of your supply network in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
 WARNING! Inadequate extension cables can be dangerous. Extension cable, plug and socket must be of
watertight construction and intended for outdoor use.
Cable connections should be kept dry and off the ground.
Bosch Power Tools
It is recommended for increased electrical safety to use a Residual Current Device (RCD) with a tripping current of not
more than 30 mA. Always check your RCD every time you use
it.
For products not sold in GB:
WARNING: For your safety, it is required that the plug attached to the machine is connected with the extension cord.
The coupling of the extension cord must be protected against
splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.
The connection lead must be inspected for signs of damage at
regular intervals and may only be used if in perfect condition.
If the supply cord is damaged, it must be replaced by a Bosch
Service Centre.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an authorised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains socket elsewhere.
Products sold in AUS and NZ only: Use a residual current device (RCD) with a rated residual current of 30 mA or less.
Maintenance
 Always wear gardening gloves when handling or working near the sharp blades.
 Keep all nuts, bolts and screws tight to be sure that the machine is in safe working condition.
 Check the grass catcher frequently for wear or deterioration.
 Examine the machine and replace worn or damaged parts
for safety.
 Ensure replacement cutting means of the right type are
used.
 Ensure replacement parts fitted are Bosch approved.
Symbols
The following symbols are important for reading and understanding the operating instructions. Please take note of the
symbols and their meaning. The correct interpretation of the
symbols will help you to use the garden product in a better
and safer manner.
Symbol
Meaning
Movement direction
Reaction direction
F 016 L70 768 | (16.11.12)
OBJ_BUCH-1349-003.book Page 4 Friday, November 16, 2012 10:13 AM
4 | English
Symbol
Declaration of Conformity
Meaning
Wear protective gloves
We declare under our sole responsibility that the product described under “Technical data” is in conformity with the following standards or standardization documents: EN 60335
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level 94 dB(A). Conformity assessment procedure according to Annex VI.
Equipment category: 32
Notified body:
SRL, Sudbury, England, Nr. 1088
Technical file (2006/42/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS4,
Stowmarket, Suffolk IP14 1EY, England
Dr. Egbert Schneider
Helmut Heinzelmann
Senior Vice President
Head of Product
Engineering
Certification
Weight
Switching On
Switching Off
Permitted action
Prohibited action
Accessories/Spare Parts
Intended Use
The garden product is intended for domestic lawn mowing.
Technical Data
Lawnmower
Article number
Rated power input
Blade width
Height of cut
Grassbox, capacity
Weight according to
EPTA-Procedure 01/2003
Protection class
Serial number
W
cm
mm
l
Rotak 32
3 600 H85 B..
1200
32
20 – 60
31
kg
6.6
/II
see type plate on the garden product
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your garden product. The trade names of the individual garden products may vary.
Noise/Vibration Information
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
04.06.2012
Mounting and Operation
Action
Delivery Scope
Handle Assembly
Snap together the Grassbox
Grassbox fitting/removing
Adjusting the Cutting Height
Connecting the Extension Lead
Starting
Stopping
Working Advice
Blade Maintenance
Selecting Accessories
Figure
1
2
3
3
4
5
5
5
5 –6
7
7
Measured sound values determined according to
2000/14/EC (1.60 m height, 1 m distance away).
Typically the A-weighted noise levels of the product are:
Sound pressure level 79 dB(A); sound power level 93 dB(A).
Uncertainty K =1 dB.
Vibration total values ah (triax vector sum) and uncertainty K
determined according to EN 60335:
ah <2.5 m/s2, K =1.5 m/s2.
F 016 L70 768 | (16.11.12)
Bosch Power Tools
OBJ_BUCH-1349-003.book Page 5 Friday, November 16, 2012 10:13 AM
English | 5
Troubleshooting
STOP
Problem
Motor refuses to start
Possible Cause
Power turned off
Mains socket faulty
Extension cable damaged
Fuse faulty/blown
Possible clogging
Motor protector has activated
Mowing too low for the conditions
Machine functions
Extension cable damaged
intermittently
Internal wiring of garden product damaged
Motor protector has activated
Garden product leaves ragged Height of cut too low
finish
Cutting blade blunt
and/or
Possible clogging
Motor labours
Blade fitted upside down
Blade not rotating while garden Cutting blade obstructed
product switched on
Blade nut/bolt loose
Excessive vibrations/noise
Blade nut/bolt loose
Cutting blade damaged
Corrective Action
Turn power on
Use another socket
Inspect cable, replace if damaged
Replace fuse
Check underneath the garden product and
clear out as necessary (always wear gardening
gloves)
Allow motor to cool and increase height of cut
Increase height of cut
Inspect cable, replace if damaged
Contact Service Agent
Allow motor to cool and increase height of cut
Increase height of cut
Replace the blade
Check underneath the garden product and
clear out as necessary (always wear gardening
gloves)
Refit blade correctly
Switch off garden product
Clear obstruction (always wear gardening
gloves)
Tighten blade nut/bolt
(17
Nm
)
Tighten blade nut/bolt
(17
Nm
)
Replace the blade
After-sales Service and Application
Service
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
E-Mail: boschservicecentre@bosch.com
www.bosch-garden.com
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the garden product.
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Bosch Power Tools
F 016 L70 768 | (16.11.12)
OBJ_BUCH-1349-003.book Page 6 Friday, November 16, 2012 10:13 AM
6 | English
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
E-Mail: rbsa-hq.pts@za.bosch.com
Disposal
Do not dispose of garden products into household waste!
Only for EC countries:
According to the European directive
2002/96/EC for Waste Electrical and Electronic
Equipment and its implementation into national
law, electrical and electronic equipment that are
no longer usable must be collected separately
and disposed of in an environmentally correct manner.
Subject to change without notice.
F 016 L70 768 | (16.11.12)
Bosch Power Tools
OBJ_BUCH-1349-003.book Page 7 Friday, November 16, 2012 10:13 AM
|7
1
1x
1x
6,6 kg
2x
2x
1x
2x
2
3
STOP
!
ICK
CL
Bosch Power Tools
F 016 L70 768 | (16.11.12)
OBJ_BUCH-1349-003.book Page 8 Friday, November 16, 2012 10:13 AM
8|
4
20 mm
60 mm
40 mm
STOP
5
2
1
F 016 L70 768 | (16.11.12)
Bosch Power Tools
OBJ_BUCH-1349-003.book Page 9 Friday, November 16, 2012 10:13 AM
|9
6
STOP
Auto-Stop
60 sec
Start
2
1
7
STOP
F 016 800 299
Bosch Power Tools
F 016 L70 768 | (16.11.12)