ClearPix FB22DN-H2 Installation guide

Installation Guide
ClearPix High Definition H.264 IP Cameras:
CFB12DN-H2, FB12DN-H2, MFB12DN-H2, CFB22DN-H2,
FB22DN-H2, MFB22DN-H2, CFB32DN-H2-WDR,
MFB32DN-H2-WDR, CFB52DN-H2 and MFB52DN-H2
920-0062B-Rev1
Important Safety Information
This manual provides installation and operation information and
precautions for the use of this camera. Incorrect installation could
cause an unexpected fault. Before installing this equipment read this
manual carefully. Please provide this manual to the owner of the
equipment for future use.
The Warning symbol indicates the presence of dangerous
voltage within and outside the product enclosure that may
constitute a risk of electric shock, serious injury or death to
persons if proper precautions are not followed.
The Caution symbol alerts the user to the presence of hazards
that may cause minor or moderate injury to persons, damage to
property or damage to the product itself if proper precautions
are not followed.
Warning — Failure to observe the following instructions
may result in severe injury or death.
•
•
•
•
•
•
Do not use near water or expose to dripping or splashing.
Do not place objects filled with liquids above the device.
Do not expose to rain or moisture.
For indoor use only.
If used outdoors, an approved outdoor mounting adapter
or enclosure is required. Consult with ClearPix for more
information.
Installation must be performed by qualified personnel only,
and must conform to all local codes.
This product is intended to be supplied by a UL Listed
Power Unit marked “Class 2” or “LPS” or “Limited Power
Source” with output rated 12 VDC or 24 VAC, 6 W min. or
Power over Ethernet (PoE), rated 48 VDC, 6 W min.
Any external power supply connected to this product may
only be connected to another ClearPix product of the
i
•
same model series. External power connections must be
properly insulated.
Do not connect directly to mains power for any reason.
Caution — Failure to observe the following instructions
may result in injury or damage to the camera.
•
•
•
•
•
•
•
•
ii
Do not install near any heat sources such as radiators,
heat registers, stoves, or other sources of heat.
Do not subject the cables to excessive stress, heavy loads
or pinching.
Do not open or disassemble the device. There are no user
serviceable parts.
Refer all servicing to qualified personnel.
Servicing may be required when the device has been
damaged (such as from a liquid spill or fallen objects), has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Do not use strong or abrasive detergents when cleaning
the device body.
Use only accessories recommended by ClearPix.
Use only UL-listed mounting bracket suitable for the
mounting surface and minimum 0.7 kg (1.5 lb) weight.
Use of controls or adjustments or performance of
procedures other than those specified in this document
may result in hazardous radiation exposure.
Regulatory Notices
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Notice
This equipment has been tested and found to comply with the limits for
a Class B computing device pursuant to Subpart B of Part 15 of FCC
rules, which are designed to provide reasonable protection against
such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause
interference, in which case the user at his/her own expense will be
required to take whatever measures may be required to correct the
interference.
Changes or modifications made to this equipment not expressly
approved by ClearPix Corporation or parties authorized by ClearPix
Corporation could void the user’s authority to operate this equipment.
Disposal and Recycling Information
When this product has reached the end of its useful life, please
dispose of it according to your local environmental laws and
guidelines.
European Union:
This symbol means that according to local laws and regulations your
product should be disposed of separately from household waste. When
this product reaches its end of life, take it to a collection point
designated by local authorities. Some collection points accept products
for free. The separate collection and recycling of your product at the
time of disposal will help conserve natural resources and ensure that it
is recycled in a manner that protects human health and the
environment.
iii
Other Notices
Compilation and Publication Notice
This manual has been compiled and published covering the latest
product descriptions and specifications. The contents of this manual
and the specifications of this product are subject to change without
notice. ClearPix reserves the right to make changes without notice in
the specifications and materials contained herein and shall not be
responsible for any damages (including consequential) caused by
reliance on the materials presented, including but not limited to
typographical and other errors relating to the publication.
Intellectual Property Notice
No license is granted by implication or otherwise under any industrial
design, industrial design rights, patent, patent rights, or copyrights of
ClearPix Corporation or its licensors. Trademarks and registered
trademarks are the property of their respective owners.
iv
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Required Tools and Materials . . . . . . . . . . . . . . . . . 3
Camera Package Contents . . . . . . . . . . . . . . . . . . . 3
Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Mounting the Camera . . . . . . . . . . . . . . . . . . 3
Connecting Cables . . . . . . . . . . . . . . . . . . . . 4
Assigning an IP Address . . . . . . . . . . . . . . . . 5
Accessing the Live Video Stream . . . . . . . . . 5
Aiming and Focusing the Camera . . . . . . . . . 6
Cable Connections . . . . . . . . . . . . . . . . . . . . . . 7
Connecting External Power . . . . . . . . . . . . . . . . . . . 7
Connecting to External Devices . . . . . . . . . . . . . . . . 8
Connecting to Microphones, Speakers
and Video Monitors . . . . . . . . . . . . . . . . . . . . . . . . . 9
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . 10
Reset to Factory Default Settings . . . . . . . . . 11
Setting the IP Address Through the ARP/Ping
Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 13
Limited Warranty & Technical Support . . . . 14
Overview
Front View
Camera Mount
(Top and Bottom)
Camera Mount
(Top and Bottom)
Serial
Number Tag
Serial
Number Tag
Feature
Description
Camera Mounts
Mounting points for the camera.
Mounts accept 1/4” - 20 UNC bolts commonly
found on mounting brackets.
Serial Number Tag Product serial number and part number label.
1
Rear View
Link LED
Connection Status LED
Power Connector Block
Ethernet Port
Audio/Video Connector
I/O Terminals
Feature
Description
Ethernet Port
Accepts an Ethernet connection to a network. Server
communication and image data transmission occurs
over this connection. Also receives power when it is
connected to a network that provides Power over
Ethernet.
Power
Connector
Block
Accepts a terminal block with either AC or DC power
connection. DC input can be either polarity. Only
required when Power over Ethernet is not available.
Audio/Video
Connector
Accepts a mini-jack connector (3.5 mm). See the
section about connecting microphones and monitors
for more information.
I/O Terminals Provides connections to external input/output
devices. See the section about connecting external
devices for more information.
Connection
Status LED
Provides information about device operation. See
LED indicators for more information.
Link LED
Indicates if there is an active connection in the
Ethernet port.
2
Installation
Required Tools and Materials
•
•
Small slotted screwdriver with 5/64” or 2 mm blade width
— for connecting power when not using Power over
Ethernet.
Mounting bracket, enclosure or tripod.
Camera Package Contents
Ensure the package contains the following:
•
•
ClearPix High Definition IP Camera
Terminal block
Installation Steps
Complete the following procedures to install the camera.
1.
2.
3.
4.
5.
Mounting the Camera on page 3
Connecting Cables on page 4
Assigning an IP Address on page 5
Accessing the Live Video Stream on page 5
Aiming and Focusing the Camera on page 6
Mounting the Camera
Camera mounting points are provided on both the top and bottom of
the camera body. Use these mounting points to mount the camera on
a bracket, in an enclosure, or on a tripod. The mounting points have
¼”-20 UNC threaded holes which allow them to accept standard
photographic mounting bolts.
Consult the installation instructions provided with the bracket,
enclosure or tripod for detailed mounting instructions.
3
Caution — This camera is designed for indoor use only.
Warning — Use only UL-listed mounting bracket suitable for
the mounting surface and minimum 0.7 kg (1.5 lb) weight.
Connecting Cables
Refer to the diagrams in the Overview section for the location of the
different connectors.
To connect the cables required for proper operation, complete the
following:
1.
2.
3.
4.
If there are external input or output devices that need to be
connected to the camera (for example: door contacts,
relays, etc), connect the devices to the camera I/O
Terminals.
For more information, see Connecting to External Devices.
If an external microphone or external video monitor needs
to be connected to the camera, connect the devices to the
camera Audio/Video Connector.
For more information, see Connecting to Microphones and
Video Monitors.
Connect the Ethernet Port (RJ45 connector) to a network
using an Ethernet network cable. The Link LED will turn on
once a network link has been established.
Connect power using one of the following methods:
•
Power over Ethernet (PoE) Class 3 — If PoE is
available, the camera is automatically detected
when the network cable is connected.
•
4
External Power — Connect an external 12 VDC or
24 VAC power source to the power connector block.
For more information, see Connecting Power.
5.
Check that the Connection Status LED indicates the
correct state.
For more information, see LED Indicators.
Assigning an IP Address
The camera automatically obtains an IP address by default. Once
connected to a network, it attempts to locate and obtain an IP address
from a DHCP server. If this fails, Zero Configuration Networking
(Zeroconf) is used to choose an IP address. When the IP address is
set using Zeroconf, the IP address is in the 169.254.0.0/16 subnet.
The IP address settings can be changed using one of the following
methods:
•
(Recommended) ClearPix Camera Installation Tool
software application.
•
Camera's web browser interface:
http://<camera IP address>/
•
ARP/Ping method. For more information, see Setting the
IP Address through the ARP/Ping Method.
•
Network Video Management software application (for
example, ClearPix Video Management).
NOTE: The default camera username is admin and the default
password is admin.
Accessing the Live Video Stream
Live video stream can be viewed using one of the following methods:
•
(Recommended) ClearPix Camera Installation Tool
software application.
•
Camera's web browser interface:
http://<camera IP address>/.
•
Network Video Management software application (for
example, ClearPix Video Management).
NOTE: The default camera username is admin and the default
password is admin.
5
Aiming and Focusing the Camera
Use the ClearPix Camera Installation Tool to aim and focus the
camera. Consult the software user guide for more information.
1.
2.
In the Image and Display settings dialog box, use the
Zoom controls to achieve the desired zoom position for the
camera.
In the Image and Display settings dialog box, use the Auto
Focus button to focus the lens.
If the desired focus position was not achieved, use the
focus near and far buttons to adjust the focus.
Caution — Do not attempt to adjust the focus and zoom on
the camera itself or the camera lens may become damaged.
6
Cable Connections
Connecting External Power
NOTE: Do not perform this procedure if Power over Ethernet (POE) is
used.
If PoE is not available, the camera needs to be powered through the
removable power connector block. Refer to the diagrams in this guide
for the location of the power connector block.
The device can be powered from 12 VDC or 24 VAC. The power
consumption information is listed in the product specifications.
To connect power to the power connector block, complete the
following steps:
1.
2.
Remove the power connector block from the device.
Remove the insulation from ¼” (6 mm) of the power wires.
Do not nick or damage the wires.
3.
Insert the two power wires into the two terminals on the
power connector block. The connection can be made with
either polarity.
Use a small slotted (5/64” or 2 mm blade width)
screwdriver to loosen and tighten the terminals.
4.
Attach the power connector block back into the receptacle
on the device.
Warning — This product is intended to be supplied by a UL
Listed Power Unit marked “Class 2” or “LPS” or “Limited
Power Source” with output rated 12 VDC or 24 VAC, 6 W
min. or PoE rated 48 VDC, 6 W min.
7
Connecting to External Devices
External devices are connected to the camera through the I/O
terminal. The pinout for the I/O terminal is shown in the following table
and diagram.
Table:External I/O Terminals
Pin
Function
Description
1
Ground
Ground
2
Input
To activate, connect the Input to the Ground
pin. To deactivate, leave disconnected or apply
between 3-15 V.
3
Output
When active, Output is internally connected
with the Ground pin. Circuit is open when
inactive. Maximum load is 25 VDC, 120 mA.
Relay
Switch
Figure: External I/O terminal schematics and example application.
8
Connecting to Microphones, Speakers
and Video Monitors
The camera can be connected to an external microphone, speaker
and video monitor through the audio/video connector. The connector
is a mini-jack (3.5 mm), and the pinout for it is shown in the following
diagram.
NOTE: The camera only supports line level mono audio input and an
NTSC or PAL video output.
The video output signal is determined by the camera flicker control
setting. When the camera flicker control is set to 60 Hz, the video
output signal is NTSC. When the flicker control is set to 50 Hz, the
video output signal is PAL. Use the ClearPix Camera Installation Tool
to configure the camera’s flicker control in the Image and Display
setup.
Audio IN
Composite
Video OUT
GND
Audio
OUT
Figure: Mini-jack audio video connector.
9
LED Indicators
Once the camera is connected to the network, the Connection Status
LED will display the camera’s progress in connecting to the Network
Video Management software.
The following table describes what the LEDs indicate:
Table:LED Indicators
Connection
State
Connection
Status LED
Description
Obtaining IP One short
Address
flash every
second
Attempting to obtain an IP address.
Discoverable Two short
flashes every
second
Obtained an IP address but is not
connected to the Network Video
Management software.
Upgrading
Firmware
Two short
Updating the firmware.
flashes and
one long flash
every second
Connected
On
10
Connected to the Network Video
Management software.
Reset to Factory Default
Settings
If the camera no longer functions as expected, you can choose to
restore the camera to its factory default settings.
Use the firmware revert button to reset the camera.
Firmware Revert Button
Figure: The firmware revert microswitch on the rear of the camera.
1.
Disconnect power from the camera.
2.
Using a straightened paperclip or similar tool, gently press
and hold the firmware revert microswitch.
While continuing to hold the microswitch, power the
device. Release the microswitch after three seconds.
3.
Caution — Do not apply excessive force. Inserting the tool
too far will damage the device.
11
Setting the IP Address
Through the ARP/Ping Method
Complete the following steps to configure the camera to use a specific
IP address:
1.
2.
Locate and copy down the MAC Address (MAC) listed on
the Serial Number Tag for reference.
Open a Command Prompt window and enter the following
commands:
a.
arp -s <New Camera IP Address> <Camera
MAC Address>
For example: arp -s 192.168.1.10 00-1885-12-45-78
b.
3.
4.
12
ping -l 123 -t <New Camera IP Address>
For example: ping -l 123 -t 192.168.1.10
Reboot the camera.
Close the Command Prompt window when you see the
following message:
Reply from <New Camera IP Address>: ...
Specifications
FBxxDN-H2
CFBxxDN-H2
MFBxxDN-H2
Camera
Audio Input
Line input, A/V mini-jack (3.5 mm)
Video Output
NTSC/PAL, A/V mini-jack (3.5 mm)
Lens
4.7-84.6mm, F1.6, auto iris 3-9mm, F1.2, P-Iris 9-22mm, F1.6, P-Iris
Network
Network
100Base-TX
Cabling Type
CAT5
Connector
RJ-45
API
ONVIF compliant (www.onvif.org)
Security
Password protection, HTTPS encryption, digest authentication, WS
authentication, user access log
Protocols
IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, TCP, UDP,
IGMP, ICMP, DHCP, Zeroconf, ARP
Streaming Protocols
RTP/UDP, RTP/UDP multicast, RTP/RTSP/TCP, RTP/RTSP/HTTP/
TCP,RTP/RTSP/HTTPS/TCP, HTTP
Mechanical
Dimensions ØxH
156 mm x 69 mm x 64 mm 115 mm x 67 mm x 53 mm
6.1” x 2.7” x 2.5”
4.5” x 2.6” x 2.5”
Weight
0.56 kg (1.2 lbs)
Camera Mount
1/4” UNC-20 (top and bottom)
0.47 kg (1.0 lbs)
Electrical
Power Source
VDC: 12 V
VAC: 24 V
PoE: IEEE802.3af Class 3 compliant
Power Consumption
6W
Power Connector
2-pin terminal block
Environmental
Operating Temperature
-10 °C to +50 °C (14 °F to 122 °F)
Storage Temperature
-10 °C to +70 °C (14 °F to 158 °F)
Humidity
20 - 80% Relative humidity (non-condensing)
Certifications
Safety
UL 60950
CE
Electromagnetic
Emissions
FCC Part 15 Subpart B Class B
EN 55022 Class B
CSA 60950
ROHS
IC ICES-003 Class B
Electromagnetic
Immunity
EN 55024
EN 61000-4-4
EN 61000-4-11
EN 61000-4-3
EN 61000-4-6
EN 61000-4-2
EN 61000-4-5
EN 60950-1
WEEE
13
Limited Warranty & Technical Support
ClearPix warrants to the original consumer purchaser, that this
product will be free of defects in material and workmanship for a
period of 3 years from date of purchase.
The manufacturer’s liability hereunder is limited to replacement of the
product, repair of the product or replacement of the product with
repaired product at the discretion of the manufacturer. This warranty is
void if the product has been damaged by accident, unreasonable use,
neglect, tampering or other causes not arising from defects in material
or workmanship. This warranty extends to the original consumer
purchaser of the product only.
CLEARPIX DISCLAIMS ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED INCLUDING, WITHOUT LIMITATION, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, EXCEPT TO THE EXTENT THAT ANY
WARRANTIES IMPLIED BY LAW CANNOT BE VALIDLY WAIVED.
No oral or written information, advice or representation provided by
ClearPix, its distributors, dealers, agents or employees shall create
another warranty or modify this warranty. This warranty states
ClearPix’s entire liability and your exclusive remedy against ClearPix
for any failure of this product to operate properly.
In no event shall ClearPix be liable for any indirect, incidental, special,
consequential, exemplary, or punitive damages whatsoever (including
but not limited to, damages for loss of profits or confidential or other
information, for business interruption, for personal injury, for loss of
privacy, for failure to meet any duty including of good faith or of
reasonable care, for negligence, and for any other pecuniary or other
loss whatsoever) arising from the use of or inability to use the product,
even if advised of the possibility of such damages. Since some
jurisdictions do not allow the above limitation of liability, such limitation
may not apply to you.
This Limited Warranty gives you specific legal rights and you may also
have other rights which vary from jurisdiction to jurisdiction.
Warranty service and technical support can be obtained by contacting
ClearPix Technical Support by phone at 1.866.883.0203 or via email at
support@ClearPix.com.
14